HG2424G Installation Instructions

HG2424G Installation Instructions
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the equipment
you are installing.
IMPORTANT: Look over the site before beginning any installation, and anticipate possible hazards, especially these:
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are
anywhere where possible contact can be made. Antennas, masts, towers, guy wires or cables
may lean or fall and contact these lines. People may be injured or killed if they are touching or
holding any part of equipment when it contacts electric lines. Make sure there is NO possibility
that equipment or personnel can come in contact directly or indirectly with power lines.
Assume all overhead lines are power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of the
mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
•
•
•
•
•
•
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting ladders and other safety equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES
CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury
in case of lightning, static build-up, or short circuit within equipment connected to the antenna.
•
•
•
The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
Lightning arrestors for antenna feed coaxial cables are available from HyperLink Technologies, Inc.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
•
•
•
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency
medical aid has been requested.
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
HyperGain™ HG2424G
2.4 GHz dBi Reflector Grid Antenna
Installation Instructions
Antenna Components Included:
(1) Antenna Feedhorn Assembly
(1) Feed Reflector
(1) Small Self-tapping Screw
(2) Grid Section Halves
(2) #M6 Stainless Steel U-Bolts w/nuts, flat and lock washers
(2) Mast Clamps
(1) Aluminum “L” Bracket
(4) #M5 x 15mm Machine Screws w/nuts, flat and lock washers
(4) #M6 x 30mm Machine Screws w/nuts, flat and lock washers
Antenna Assembly Instructions:
Lock Washer & Nut
Feed Reflector
Reflector Grid
Feedhorn
Small Self-Tapping Screw
#M5 Machine Screw
Assemble the halves of the Reflector Grid using
(4) #M5 machine screws with lock washers, flat
washers and nuts as shown.
IP-00002 Rev. C – 04/05 Page 1/3
Install the Feed Reflector to the front of the
Feedhorn using the small self-tapping screw.
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
HyperGain™ HG2424G Installation Instructions
Determine the polarity which will be chosen
for the antenna installation. The antenna can
be installed either vertically or horizontally
polarized.
Position the “L” Bracket to the back of the Grid Assembly,
noting the orientation required for the desired polarity.
Position the Feedhorn to the front of the Grid Assembly,
again noting the orientation required for the desired polarity.
The two polarities are illustrated below:
Secure the Feedhorn & “L” Bracket to the Grid Assembly
using (4) #M6 machine screws with lock washers, flat
washers and nuts.
Feed Reflector
“L” Bracket
Horizontal
Polarity
Feedhorn
Vertical
Polarity
Important Note: Feed Reflector must be orientated to
grid as shown for optimal antenna performance.
Grid Assembly
Install the (2) Mast Clamps on the U-Bolts as shown
and fasten to the “L” Bracket using (4) lock washers
and (4) Nuts.
“L” Bracket
OPTIONAL TILTED MOUNTING
Fixed Tilt Positions
Tilt Slot
Mast
Mast Clamps
U-Bolts
IP-00002 Rev. C – 04/05 Page 2/3
To mount antenna assembly in a tilted position,
attach (1) U-Bolt assembly to either the fixed tilt
positions or to the tilt slot (as shown) on the
“L” Bracket.
Copyright © This drawing is property of L-com Global Connectivity. All rights reserved.
L-com Global Connectivity | 50 High St., West Mill, 3rd floor, Suite #30 | North Andover, MA 01845 | USA
© L-com, Inc. All Rights Reserved. L-com Global Connectivity and the L-com Logo are registered marks.
Toll Free Ordering and Technical Support: 1-800-343-1455
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement