YAESU FT-817ND HF/VHF/UHF Transceiver Operating Manual

Below you will find brief information for HF/VHF/UHF Transceiver FT-817ND. The FT-817ND is a compact, innovative multiband, multimode portable transceiver for the amateur radio MF/HF/VHF/UHF bands covering the 160-10 meter bands, plus the 6 m, 2 m, and 70 cm bands. It includes SSB, CW, AM, FM, and Digital modes operation. The FT-817ND is designed for use from an external DC power source or internal batteries and provides five watts of power output from a 13.8-Volt external power supply.

PDF Download

Document

HF/VHF/UHF
ALL MODE TRANSCEIVER
FT-817ND
OPERATING MANUAL
Downloaded by
RadioAmateur.EU
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
Contents
Introduction .................................................... 1
Specifications .................................................. 2
Accessories &amp; Options ................................... 4
Plug Pinout ...................................................... 5
Installation ...................................................... 6
Connecting the Supplied YHA-63 Antenna ......... 6
Connecting the Microphone ................................. 7
Shoulder Strap Installation ................................... 7
Rubber Foot Installation ....................................... 7
Alkaline Battery Installation and Use .................. 8
External Power Connections ................................ 9
FNB-85 Ni-Cd Battery Pack Installation and Use .. 10
Front Panel Control &amp; Switches ................. 12
Side Panel Switch &amp; Connectors ................ 16
Rear Panel Connectors ................................ 17
Operation ...................................................... 18
Turning the Transceiver On and Off .................. 18
Supply Voltage Display ...................................... 18
Operating Band Selection .................................. 19
Mode Selection ................................................... 19
Adjusting the Audio Volume Level .................... 19
Menu Quick Start ............................................... 20
Adjusting the RF Gain and Squelch ................... 20
Setting the Operating Frequency ........................ 21
Stacked VFO System ......................................... 21
Operation on 5 MHz Band
(U.S. Version Only) ............................................ 22
Receiver Accessories ..................................... 23
Clarifier (Receiver incremental Tuning) ............ 23
IF SHIFT ............................................................ 24
AGC (Automatic Gain Control) ......................... 25
Noise Blanker ..................................................... 25
IPO (Intercept Point Optimization) .................... 25
ATT (Front End Attenuator) ............................... 26
AM/FM DIAL .................................................... 26
Automatic Power-Off Feature ............................ 27
Transmitter Operation ................................. 28
SSB Transmission .............................................. 28
Basic Setup/Operation ................................... 28
Adjusting the transmitter Power Output ... 28
VOX Operation ............................................. 29
CW Transmission ............................................... 30
Operation using Straight Key/
External Keying Device ................................ 30
Operation using
the Built-in Electronic Keyer ........................ 32
FM Transmission ................................................ 33
Basic Setup/Operation ................................... 33
Repeater Operation ........................................ 33
Tone Search Scanning ............................... 35
DCS Operation .............................................. 36
DCS Search Scanning ............................... 36
ARTSTM (Auto Range Transpond System)
Operation ....................................................... 37
CW Identifier Setup ....................................... 37
Digital Mode Operation (SSB-Based AFSK) .... 38
RTTY (Radio TeleType) Operation ............... 38
PSK31 Operation ........................................... 39
“USER” Defined Digital Modes ................... 40
Packet (1200/9600 bps FM) Operation .............. 41
AM Transmission ............................................... 42
Split Frequency Operation ................................. 42
Time-Out Timer .................................................. 43
WeatherFax Monitoring ..................................... 43
Memory Operation ...................................... 44
QMB Channel ..................................................... 44
Memory Operation on
“Regular” Memory Channels ............................. 45
Normal Memory Storage .............................. 45
Split-Frequency Memory Storage ................. 45
Memory Channel Recall ................................ 46
Masking Memory .......................................... 47
Memory Operation on
“HOME” Channel Memories ............................. 48
Labeling Memories ............................................ 49
Spectrum Scope Monitor Operation .......... 50
Smart SearchTM Operation .......................... 51
Scanning Operation ..................................... 52
Scanning Operation ............................................ 52
Scan Skip Programming (Memory Mode Only) .... 52
Scan-Resume Choices .............................. 52
Programmable Memory Scan (PMS) Operation . 54
Dual Watch Operation ................................. 56
Operation on Alaska Emergency Frequency:
5167.5 kHz (U.S. Version Only) ........................ 57
Menu Operation ........................................... 58
Clonning ........................................................ 69
CAT System Programming ....................... 70
Installation of Optional Accessories ........... 74
Option Filters YF-122S/YF-122C ................... 74
High-Stability Reference Oscillator TCXO-9 ... 75
Power-on Microprocessor Reset Procedure ..... 76
Appendix ....................................................... 77
Setup of Memories for Low Earth Orbit (LEO)
FM Satellite Operation ....................................... 77
BAND DATA Format ......................................... 80
INTRODUCTION
The FT-817ND is a compact, innovative multiband, multimode portable transceiver for the
amateur radio MF/HF/VHF/UHF bands. Providing coverage of the 160-10 meter bands
(include the 60 m band: USA version) plus the 6 m, 2 m, and 70 cm bands, the FT-817ND
includes operation on the SSB, CW, AM, FM, and Digital modes, yielding the most comprehensive performance package available for portable operation.
Designed for use either from an external DC power source or internal batteries, the FT817ND provides five watts of power output from a 13.8-Volt external power supply. When
using the FNB-85 Ni-MH Battery Pack or 8 “AA” Alkaline Cells (not supplied), the FT817ND automatically switches to 2.5 Watts of output power. Via the Menu system, “High”
power may be selected during battery operation, providing as much as 5 Watts of output,
depending on the operating frequency.
The multi-function Liquid-Crystal Display includes Blue, Amber, and Violet backlighting,
which may be disabled for battery conservation. The display includes bar-graph indication
of power output, ALC voltage, SWR, and modulation level. Also include are a number of
operating status icons, as well as the function displays for the three operating function keys
(
,
, and
).
Among the advanced features of the FT-817ND are many incorporated only in large basestation transceivers. These include Dual VFOs; Split-Frequency operation; IF Shift; Clarifier (“R.I.T.”); IF Noise Blanker; AGC Fast/Slow/Auto/Off selection; RF Gain and Squelch
control; IPO (Intercept Point Optimization) and a receiver front-end Attenuator; AM Aircraft reception; AM and FM Broadcast reception; VOX; Built-in Electronic Keyer; Adjustable CW Pitch; Automatic FM Repeater Shift (ARS); Built-in CTCSS Encoder/Decoders;
ARTS™ (Auto-Range Transponder System); Smart Search™ Automatic Memory Loading
System; Spectrum Scope; 200 Memories plus Home Channels and Band-limiting Memories; Alpha-Numeric Labeling of Memories; Automatic Power-Off (APO) and Time-Out
Timer (TOT) functions; Computer Interface capability; and Cloning capability.
We urge you to read this manual in its entirety, so as to gain a full understanding of the
amazing capability of the exciting FT-817ND Portable Transceiver.
FT-817ND Operating Manual
1
SPECIFICATIONS
GENERAL
Receive: 100 kHz-30 MHz
50 MHz-54 MHz
76 MHz-108 MHz (WFM only)
Downloaded by
87.5 MHz-108 MHz (EU)
RadioAmateur.EU
108 MHz-154 MHz (USA)
144 MHz-148 (146) MHz (Other markets)
430 (420) MHz-450 (440) MHz
Transmit: 160-6 Meters (USA: includes 60 meters)
2 Meters
70 Centimeters (Amateur bands only)
5.1675 MHz Alaska Emergency Frequency (USA only)
Emission Modes:
A1 (CW), A3 (AM), A3J (LSB/USB), F3 (FM),
F1 (9600 bps packet), F2 (1200 bps packet)
Synthesizer Steps (Min.): 10 Hz (CW/SSB), 100 Hz (AM/FM)
Antenna Impedance:
50 Ohms, Unbalanced (Front: Type BNC, Rear: Type M)
Operating Temp. Range: –10 &deg;C to +60 &deg;C (+14 &deg;F to +140 &deg;F)
Frequency Stability:
&plusmn;4 ppm from 1 min. to 60 min after power on.
@25 &deg;C: 1 ppm/hour
&plusmn;0.5 ppm/1 hour @25 &deg;C, after warmup (with optional TCXO-9)
Supply Voltage:
Normal: 13.8 VDC &plusmn; 15 %, Negative Ground
Operating: 8.0-16.0 V, Negative Ground
FBA-28 (w/8 “AA” Alkaline Cells): 12.0 V
FNB-85 (Ni-MH Battery Pack): 9.6 V
Current Consumption:
Squelched: 250 mA (Approx.)
Receive: 450 mA
Transmit: 2.0 A
Case Size (W x H x D):
135 x 38 x 165 mm (5.31” x 1.5” x 6.50”)
Weight (Approx.):
1.17 kg (2.58 lb) w/Alkaline battery, antenna, w/o Microphone
Frequency Range:
TRANSMITTER
5 W (SSB/CW/FM), 1.5 W (AM Carrier) @13.8 V
SSB: Balanced Modulator
AM: Early Stage (Low Level)
FM: Variable Reactance
FM Maximum Deviation: &plusmn;5 kHz (FM-N: &plusmn;2.5 kHz)
Spurious Radiation:
–50 dB (1.8-29.7 MHz)
–60 dB (50/144/430 MHz)
Carrier Suppression:
&gt;40 dB
Opp. Sideband Supp.:
&gt;50 dB
SSB Frequency Response: 400 Hz-2600 Hz (–6 dB)
Microphone Impedance: 200-10k Ohms (Nominal: 600 Ohms)
RF Power Output:
Modulation Types:
2
FT-817ND Operating Manual
SPECIFICATIONS
RECEIVER
Circuit Type:
Double-Conversion Superheterodyne
Intermediate Frequencies: 1st: 68.33 MHz (SSB/CW/AM/FM); 10.7 MHz (WFM)
2nd: 455 kHz
SSB/CW
AM
FM
Sensitivity:
100 kHz-500 kHz –
–
–
500 kHz-1.8 MHz –
32 &micro;V
–
1.8 MHz-28 MHz 0.25 &micro;V
2 &micro;V
–
28 MHz-30 MHz
0.25 &micro;V
2 &micro;V
0.5 &micro;V
50 MHz-54 MHz
0.2 &micro;V
2 &micro;V
0.32 &micro;V
144/430 MHz
0.125 &micro;V
–
0.2 &micro;V
(IPO, ATT off, SSB/CW/AM = 10 dB S/N, FM = 12 dB SINAD)
Squelch Sensitivity:
SSB/CW/AM
FM
1.8 MHz-28 MHz 2.5 &micro;V
–
28 MHz-30 MHz
2.5 &micro;V
0.32 &micro;V
50 MHz-54 MHz
1 &micro;V
0.2 &micro;V
144/430 MHz
0.5 &micro;V
0.16 &micro;V
(IPO, ATT off)
Image Rejection:
HF/50 MHz: 70 dB
Downloaded by
144/430 MHz: 60 dB
RadioAmateur.EU
IF Rejection:
60 dB
Selectivity (–6/–60 dB):
SSB/CW: 2.2 kHz/4.5 kHz
AM: 6 kHz/20 kHz
FM: 15 kHz/30 kHz
FM-N: 9 kHz/25 kHz
SSB (optional YF-122S installed): 2.3 kHz/4.7 kHz (–66 dB)
CW (optional YF-122C installed): 500 Hz/2.0 kHz
CW (optional YF-122CN installed): 300 Hz/1.0 kHz
AF Output:
1.0 W (8 Ohms, 10% THD or less)
AF Output Impedance: 4-16 Ohms
Specifications are subject to change without notice, and are guaranteed within amateur
bands only.
Frequency ranges vary according to transceiver version; check with your dealer.
FT-817ND Operating Manual
3
ACCESSORIES &amp; OPTIONS
SUPPLIED ACCESSORIES
MH-31A8J
FNB-85
NC-72B/C/U
FBA-28
YHA-63
E-DC-6
Shoulder Strap
Ferrite Core
Rubber Foot
Hand Microphone
Ni-MH Battery Pack (9.6 V, 1400 mAh)
Battery Charger
Battery Case (holds 8 “AA” size Alkaline cells [not supplied])
Whip Antenna for (50/144/430 MHz)
DC Cable
FNB-85
FNB-72
NC-72B/C/U YF-122S
YF-122C
YF-122CN
TCXO-9
MH-36E8J
CT-62
CT-39A
Ni-MH Battery Pack (9.6 V, 1400 mAh)
Ni-Cd Battery Pack (9.6 V, 1000 mAh)
Battery Charger
Collins SSB Filter (2.3 kHz/4.7 kHz: –6 dB/–66 dB)
Collins CW Filter (500 Hz/2 kHz: –6 dB/–60 dB)
Collins CW Filter (300 Hz/1 kHz: –6 dB/–60 dB)
TCXO Unit (&plusmn;0.5 ppm)
DTMF Microphone
CAT Interface Cable
Packet Cable
Available Options
: “B” suffix is for use with 120 VAC, “C” suffix is for use with 230-240 VAC, and “U”
suffix is for use with 230 VAC.
4
FT-817ND Operating Manual
Downloaded by
RadioAmateur.EU
FT-817ND Operating Manual
PLUG PINOUT
5
INSTALLATION
CONNECTING THE SUPPLIED YHA-63 ANTENNA
Your FT-817ND is supplied with a three-section antenna, model YHA-63 which is designed
for optimum performance on the 50 MHz, 144 MHz, and 430 MHz. It also works well on
the FM broadcast and other VHF bands. This antenna is intended for connection to the front
panel’s BNC-type antenna connector.
For HF and/or 50 MHz operation, most hikers carry their own dipole or collapsible vertical
antenna, fed by a small-diameter coaxial cable terminated in a type “M” (PL-259) plug, and
these kinds of antennas may be connected to the rear panel’s antenna connector.
The YHA-63 should be connected to the top panel’s “BNC” connector, using the following
guidelines:
For 144/430 MHz operation (only), connect the shorter cap section to the screw post on
the top of the main antenna shaft, then screw the assembled YHA-63 onto the BNC
connector, twisting it 1/4 turn clockwise to secure the antenna.
For 50 MHz operation, unscrew the
short cap section, and replace it with
the long cap section. The long cap
section will provide good results on
144/430 MHz, as well, but those
owners not using 50 MHz may prefer the shorter total length of the
YHA-63 when using the short cap
on 144/430 MHz.
For shortwave listening using a random-length wire antenna for reception only, you may wish to consider
connection of the wire between the
main YHA-63 shaft and the cap,
using a “spade lug” or similar lug
on the end of the wire to provide a
secure connection between the cap
and the rest of the antenna.
Menu #07 (“ANTENNA”) allows
you to define which connector
(“Front” or “Rear”) is used on a
particular band. See page 60 for details.
6
FT-817ND Operating Manual
INSTALLATION
CONNECTING THE MICROPHONE
To connect the microphone, plug its connector (latch side UP) into the MIC jack on the
right side of the transceiver. Press it
gently inward until you hear the
“click” of the latch.
To disconnect the microphone, press
gently on the “PUSH ” label on
top of the microphone connector’s rubber boot.
While pressing on this spot, gently pull the connector outward from the body of the transceiver.
Note: During “Digital” or “Packet” operation, it is not necessary to disconnect the microphone, as activation of the PTT line from the DATA connector automatically cuts off the
audio input from the MIC jack.
SHOULDER STRAP INSTALLATION
The convenient Shoulder Strap is designed for maximum comfort and security for your FT817ND transceiver.
Refer to the illustration, and connect the
shoulder strap to the attachment tabs just
behind the front panel of the FT-817ND.
Be sure to have the shoulder strap aligned
correctly, without twists in the straps.
A convenient microphone hanger is located
on one end of the padded top section of
the Shoulder Strap. When not in use, the
microphone may be affixed here, freeing
both of your hands for other tasks.
RUBBER FOOT INSTALLATION
Four Rubber Feet are provided with your FT817ND, for ease of use when operating from a
base station or camp table.
Refer to the illustration, and affix the Rubber
Feet in the appropriate locations.
FT-817ND Operating Manual
7
INSTALLATION
LKALINE
BATTERY INSTALLATION AND USE
The FT-817ND is supplied with the FBA-28 holder for Alkaline “AA” cells. A fresh set of
Alkaline cells should provide approximately 5.5 hours of reception under typical conditions.
1. To install or replace the AA cells, first remove the battery cover from the bottom side of
the transceiver. Slide the battery cover latch forward, as shown in the illustration, then
fold the battery cover upward and set it aside temporarily.
2. Install the Alkaline AA cells as shown in the illustration, paying particular attention to
the correct polarity of the batteries.
3. When all batteries have been successfully installed, replace the battery cover.
Important Notes
When the transceiver is to be stored for a long period of time without use (longer
than ten days), remove the batteries from the FBA-28 holder, to avoid the possibility of battery leaking causing damage to the transceiver. Inspect the FBA-28
battery holder occasionally for signs of corrosion or battery leakage, and remove
the batteries immediately if any such damage is observed.
The FBA-28 battery holder is designed for use solely with Alkaline type “AA”
cells. Do not attempt to use Ni-Cd or other rechargeable cells in the FBA-28,
because it does not contain the protection circuitry required when using rechargeable cells.
When replacing batteries, replace all eight AA cells simultaneously with fresh
batteries.
When the battery voltage is approaching the value which indicates depletion is
near, the small “
” will blink, indicating it is time to replace the batteries.
8
FT-817ND Operating Manual
INSTALLATION
EXTERNAL POWER CONNECTIONS
The FT-817ND may be connected to an external 13.8 Volt DC power source providing at
least 3 Amps of continuous-duty current.. The supplied E-DC-6 DC cable may be used for
DC connections.
While connected to an external DC source, if you have installed the supplied FNB-85 NiMH Battery Pack, the E-DC-6 connection to the external DC power source will allow operation of the FT-817ND while charging of the FNB-85 is in progress.
When making DC power connections, be absolutely certain to follow the markings on the EDC-6 so as to ensure proper polarity of the connection to the power supply. Connect the RED
AND BLACK wire to the Positive (+) power supply terminal, and connect the SOLID BLACK wire
to the Negative (-) power supply terminal.
FT-817ND
Notice
Be extremely careful when making power supply connections. Use only a 13.8 Volt
DC Supply, and carefully observe the proper electrical polarity. Serious damage may
result if these precautions are not observed.
The Limited Warranty on this product does not cover damage caused by improper
power supply connections, or improper power supply voltage.
FT-817ND Operating Manual
9
INSTALLATION
FNB-85 NI-MH BATTERY PACK INSTALLATION AND USE
The supplied FNB-85 Ni-MH Battery Pack provides 9.6 Volts of DC power for your FT817ND, with a maximum capacity of 1400 mAh.
Installation
1. To install the FNB-85 Ni-MH Battery Pack, first remove the battery compartment cover,
as described previously.
2. Lift out the FBA-28 battery holder, and disconnect the short cable connected to the
FBA-28, as shown in the illustration.
3. Connect the short cable to the mating connector on the FNB-85, and install the FNB-85
in the battery compartment.
4. Replace the battery compartment cover.
FNB-85
FBA-28
10
FT-817ND Operating Manual
INSTALLATION
FNB-85 NI-MH BATTERY PACK INSTALLATION AND USE
Charging
Charging of the FNB-85 requires the use of either the supplied NC-72B/C* charger, or an
external 13.8 Volt (&plusmn;15%) DC source. If the NC-72B/C is used, the FT-817ND must be
turned off during charging; if an external 13.8 Volt DC source is used (connected via the
supplied E-DC-6 cable), then you may operate the FT-817ND while charging is in progress.
1. Turn the FT-817ND off (see page 18), then connect the supplied NC-72B/C DC connector to the INPUT: 13.8V jack on the rear panel of the FT-817ND.
2. Plug the NC-72B/C into the nearest AC wall outlet.
3. Press the FT-817ND’s
switch for one second to turn the transceiver on.
4. Press the
key momentarily.
5. Rotate the
knob so that the function row containing “[CHG, VLT, DSP]” appears
on the display.
6. Press the
key to select the [CHG] option (the display will immediately revert to the
regular frequency display).
7. Turn the FT-817ND off. You will now observe that the LED just
above the main tuning dial is glowing Orange, and the display
will indicate “CHG TIME RMN” and “7:59” to indicate the time
remaining before a full charge is achieved on the FNB-85.
Important Notice
For Charging the optional FNB-72 Ni-Cd Battery Pack
If you wish to charge the optional FNB-72 Ni-Cd Battery Pack using the supplied
NC-72B/C Battery Charger, you must set the Battery Charging Time to “6 Hours”
via Menu #11, to prevent over charging the battery. See page 61 for detail.
FT-817ND Operating Manual
11
FRONT PANEL CONTROL &amp; SWITCHES
PWR Switch
Press and hold in the
switch for one second to turn to the transceiver on or off.
AF Knob
The (inner)
knob adjusts the receiver audio volume level presented to the internal
or external speaker. Clockwise rotation increases the volume level.
SQL/RF Knob
In the USA version, this (outer)
knob adjusts the gain of the receiver’s RF and
IF stages. Using Menu Selection 45, this control may be changed to function as a Squelch
control, which may be used to silence background noise when no signal is present. In
the other versions, its default setting is set to “Squelch.”
LOCK Key
Pressing this key locks the front panel keys so as to prevent accidental frequency change.
V/M Key
Pressing this key switches frequency control between the VFO and Memory Systems.
TRANSMIT/BUSY Indicator
This LED glows green when the squelch opens, and turns red during transmit. It also
glows orange during charging of the FNB-85 (Ni-MH) / FNB-72 (Ni-Cd) battery pack.
MAIN Dial
This is the main tuning dial for the transceiver. It is used both for frequency tuning as
well as “Menu” setting in the transceiver.
F Key
Pressing this key momentarily changes the display to show the operating functions available via the
,
,
keys.
Press and hold this key for one second to activate the “Menu” mode.
12
FT-817ND Operating Manual
FRONT PANEL CONTROL &amp; SWITCHES
FUNC Keys
These three keys select many of the most important operating features of the transceiver. When pressing the
key, the current function of that key appears above each
of the
,
,
keys (along the bottom of the LCD); rotating the
knob
scrolls the display through eleven rows of functions available for use via the
,
,
keys.
The available features are shown in chart on the next page.
BAND(DWN)/BAND(UP) Key
Pressing either of these keys momentarily will cause the frequency to be moved up or
down by one frequency band. The selections available are:
Recalling the 5 MHz band (U.S. model) requires different procedure. See page 22 for
details.
MODE()/MODE() Key
Pressing either of these keys momentarily will change the operating mode. The selections available are:
HOME Key
Pressing this key momentarily recalls a favorite “HOME” frequency memory.
SEL Knob
This detented rotary switch is used for tuning, memory selection, and function selection
for the
,
,
keys of the transceiver.
CLAR Key
Press this key momentarily to activate the Receiver Clarifier feature. When this feature
is activated, the
knob may be used to set a tuning offset of up to &plusmn;9.99 kHz. The
transmitter’s frequency is not affected by the setting of the Clarifier.
Press and hold this key for 1/2 second to activate the IF Shift feature, which allows you
to use the
knob to adjust the center frequency of the IF filter’s passband response.
ANT Jack
Connect the supplied 50/144/430 MHz rubber flex antenna (or another antenna presenting a 50Ω impedance) to this BNC connector.
In its default setting, this jack does not function on the HF bands. If you want to enable
this jack on the HF bands, recall and change the setting of Menu #07.
FT-817ND Operating Manual
13
FRONT PANEL CONTROL &amp; SWITCHES
Key
1
A/B
key to switch
Press the
between VFO-A and VFO-B
on the display.
2
MW
key
Press and hold in the
for 1/2 second to transfer the
contents of the VFO into a
Memory register.
STO
Press the
key to store
the contents of the VFO into
the QMB (Quick Memory
Bank) register.
RPT
Press the
key to select
the direction of the uplink frequency shift (“–,” “+,” or Simplex) during FM repeater operation.
Press and hold in the
key
for 1/2 second to recall Menu
#42 (for setting the shift frequency offset).
SCN
Press the
key to initiate
scanning (in the direction of
higher frequencies).
SSM
Press the
key to activate
the Spectrum Scope Monitor
feature.
Press and hold in the
key
for 1/2 second to recall Menu
#43 (for selecting the SSM
sweep mode).
IPO
Press the
key to bypass
the receiver preamplifier,
thereby activating Intercept
Point Optimization for improved overload characteristics.
The IPO feature does not
function on 144/430 MHz.
3
4
5
6
7
14
Key
A=B
key
Press and hold in the
for &frac12; second to copy the contents of VFO-A into the VFOB register, so that the two
VFOs’ contents will be identical.
MC
key to desigPress the
nate the current Memory
channel to be “skipped” during scanning.
RCL
Press the
key to recall
the QMB Memory.
SPL
key to activate
Press the
Split frequency operation between VFO-A and VFO-B.
TAG
key to select
Press the
the display type (Frequency
or Alpha-numeric Tag) during
Memory operation.
PMS
Press the
key to activate
the Programmable Memory
Scan feature.
REV
Press the
key to reverse
the transmit and receive frequencies while working
through a repeater.
TON
Press the
key to activate
CTCSS or DCS operation.
Press and hold in the
key
for 1/2 second to recall Menu
#48 (for selecting the CTCSS
tone frequency).
PRI
Press the
key to activate
the Priority Scan feature.
DW
Press the
key to activate
the Dual Watch system.
SCH
Press the
key to activate
Smart SearchTM operation.
ART
Press the
key to initiate
the Auto-Range Transponder
mode.
Press and hold in the
key
for 1/2 second to recall Menu
#09 (for selecting the ARTS
“Beep” option).
NAR
Press the
key to activate
the “Narrow” filter mode in the
CW (optional YF-122C or YF122CN required) or SSB (optional YF-122S required)
mode. On the FM mode, it
also selects the low-deviation
mode required for HF FM operation on 29 MHz.
Press and hold in the
key
for 1/2 second to recall Menu
#38 (to Enable/Disable the
optional filter during installation).
ATT
Press the
key to engage
the receiver front-end attenuator, which will reduce all signals and noise by approximately 10 dB.
The ATT feature does not
function on 144/430 MHz.
FT-817ND Operating Manual
FRONT PANEL CONTROL &amp; SWITCHES
Key
8
NB
key to activate
Press the
t h e r e c e i v e r ’s I F N o i s e
Blanker.
9
PWR
key to select
Press the
the transmitter power output
level (LOW 1, LOW 2, LOW 3, or
HIGH).
10
VOX
Press the
key to enable
the VOX (voice-operated
transmitter switching system)
in the SSB, AM, and FM
modes.
Press and hold in the
key
for 1/2 second to recall Menu
#51 (for setting the VOX Gain
level).
CHG
Press the
key to initiate
Battery Charging.
Press and hold in the
key
for 1/2 second to recall Menu
#11 (for selecting the Charging period).
TCH
Press the
key to initiate
Tone Search.
11
12
Key
AGC
key to select
Press the
the recovery time (FAST, SLOW,
AUTO, or OFF) for the
receiver’s AGC system.
MTR
key to select
Press the
the display function of the
meter in the transmit mode
(Power, ALC, SWR, or MOD
indication).
BK
Press the
key to activate
CW “Semi” Break-in operation.
Press and hold in the
key
for 1/2 second to recall Menu
#17 (for setting the CW Delay time). At a setting of 10
ms, operation emulates full
QSK performance.
VLT
Press the
key to display
the current battery voltage.
DCH
Press the
key to initiate
DCS Search.
Key
–
No function
–
No function
KYR
Press the
key to activate
the built-in Electronic Keyer.
Press and hold in the
key
for 1/2 second to recall Menu
#21 (for setting the Keyer
speed).
DSP
Press the
key to switch
the display between the Large
Character and Small Character modes.
–
No function
*The Operating Function number in this column does not appear on the LCD.
Display Icons
FT-817ND Operating Manual
15
SIDE PANEL SWITCH &amp; CONNECTORS
MIC Jack
Connect the supplied MH-31A8J Hand Microphone to this jack.
SP/PH Jack
This 3.5-mm, 2-pin jack provides variable audio output for an external speaker (4 Ω ~
16 Ω impedance) or earphones. The audio level varies according to the setting of the
front panel’s
knob.
When you insert an earphone plug into this jack, the SP-PH slide switch (located to the right side of this jack) MUST BE set to the “PH” position, to prevent the possibility of injury to your ears.
SP-PH Switch
If you use earphones with this transceiver, move this switch to the “PH” position before
inserting the earphone plug into the SP/PH Jack, to prevent injury your ears.
16
FT-817ND Operating Manual
REAR PANEL CONNECTORS
INPUT:13.8V
Jack (
)
This is the DC power supply connection for the transceiver, used when operating the
transceiver with an external power supply. Use the supplied DC cable to connect this
jack to the car battery or base station DC power supply, which must be capable of
supplying at least 3A @ 8 ~ 16 VDC. This jack is also used for battery charging (when
using the supplied FNB-85 battery pack).
GND Terminal
For best performance and safety, this Ground lug may be connected to a good earth
ground using a short, heavy, braided cable.
KEY Jack
This 3.5-mm, 3-pin jack is used for connection to a CW keyer paddle or a straight key.
DATA Jack
This 6-pin, mini-DIN jack accepts AFSK input from a Terminal Node Controller (TNC);
it also provides fixed-level Receiver Audio Output, Push-To-Talk (PTT), Squelch Status, and ground lines.
ACC Jack
This 8-pin, mini-DIN jack provides a closure to ground during transmission, ALC, a
transmitter-inhibit pin, and “band data” for connection to an external amplifier. It is also
used for Transceiver-to Transceiver Cloning and for control of this transceiver using a
personal computer.
ANT Jack
Connect your HF and/or 50 MHz antenna’s 50 Ω coaxial cable to this M-type (“SO239”) connector.
In its default setting, this jack does not function on 50/144/430 MHz bands. If you want to
enable this jack on 50/144/430 MHz bands, recall and change the settings of Menu #07.
FT-817ND Operating Manual
17
OPERATION
Hi! I’m R.F. Radio, and I’m here to guide you through the fine points of the setup
and use of your new FT-817ND. I know your anxious to get on the air, but I
encourage you to read the “Operation” section of this manual as thoroughly as possible,
so you’ll get the most out of this fantastic new rig. Now. . .let’s get operating!
TURNING THE TRANSCEIVER ON AND OFF
1. To turn the transceiver on, press and hold in
the
switch for one second.
2. To turn the transceiver off, again press and
hold in the
switch for one second.
The one-second delay helps you avoid accidental switching on (or off) of DC power.
SUPPLY VOLTAGE DISPLAY
When you turn on the transceiver, the DC supply voltage is indicated
in the upper right corner of the LCD for two seconds. After this interval, the display will resume its normal indication of the operating
mode (VFOa, VFOb, or Memory Channel Number).
To view the supply voltage at any time during operation:
key momentarily, then rotate the
knob to select Operating Function
1. Press the
Row 11* [CHG, VLT, DSP] on the display.
(VLT) key momentarily to display the supply voltage in the upper right
2. Press the
corner of the LCD.
(VLT) key.
3. To cancel the supply voltage display, again press the
Remember, the Operating Row Number does not appear on the display.
18
FT-817ND Operating Manual
OPERATION
OPERATING BAND SELECTION
This transceiver covers an incredibly wide frequency range, over which a number of different
operating modes are used. Therefore, this
transceiver’s frequency coverage has been divided
into different operating bands, each of with has
its own pre-set channel steps and operating modes.
You can change the channel steps and operating mode once you get started, of course, per
the next section.
To change the frequency band, press either the
the next lower or higher operating band, respectively.
or
key to move to
1) Recalling the 5 MHz band (U.S. model) requires different procedure. See page
22 for details.
2) VFOa and VFOb are independent VFOs, so they may be set to different bands. See the
“Stacked VFO System” discussion on page 21 for details.
MODE SELECTION
Press either the
or
key to
move among the eight settings for the operating
modes, respectively.
You can also set VFOa and VFOb to different modes in the same band, allowing
you to have a “Phone” VFO and a “CW” VFO, for example.
ADJUSTING THE AUDIO VOLUME LEVEL
Rotate the
tening level.
knob to set a comfortable lis-
When operating in the “DIG” or “PKT” modes,
you may set the
knob to any comfortable
setting, or even all the way off, because the output from the DATA jack is a fixed-level audio signal.
Start with the
knob set fully counter-clockwise, especially when using FM
(the background noise on FM can be surprisingly loud)!
FT-817ND Operating Manual
19
OPERATION
MENU QUICK START
Many aspects of this transceiver’s configuration may be customized using the convenient
“Menu” system, which allow you to configure many “set and forget” settings just the way
you want to. A full discussion of the Menu system beings on page 58; for now, here is a brief
discussion on how to change Menu settings:
key for one second to enter the Menu mode.
1. Press and hold in the
2. Rotate the
knob to recall the Menu item to be changed (for example, Menu #01,
which Enables or Disables the Automatic Repeater Shift on the 144 MHz band).
knob to set this feature (in this example, the default setting is “EN3. Rotate the
ABLE,” so rotate the
knob to set this feature to “DISABLE.”
key for one second to save the new setting and exit to normal
4. Press and hold in the
operation.
key to change an operating function,
If you have momentarily pressed the
press the
key momentarily again (to clear the function indications for the
,
,
keys) before engaging the Menu.
ADJUSTING THE RF GAIN AND SQUELCH
The
control is configured differently,
depending on the country to which the FT-817ND
has been exported. In the U.S. version, the default function of this control is “RF Gain.” The
control is set via
configuration of the
Menu #45; see page 67 for details.
If your transceiver is configured for “RF Gain” use, rotating this control fully clockwise in
the SSB/CW/Digital modes will provide best sensitivity. To reduce the receiver’s RF Gain
somewhat, rotate this control counter-clockwise slightly. You will observe an increasing
number of bars on the S-meter as you rotate the
control counter-clockwise; this
indicates increasing AGC voltage, which is causing the front-end gain to be reduced. In the
FM and Packet modes, this control will automatically be set to an “Auto-Squelch” mode,
wherein the FM/Packet squelch threshold is pre-set at the factory; the
control still
acts as an “RF Gain” control, however, and it normally should be set fully clockwise.
If this control is configured for “SQL” operation, the FT-817ND’s RF Gain will be set for
maximum sensitivity in all modes, and the
control will function solely as a Squelch
control. In this case, rotate the
control to the point where the background noise is
just silenced; this will provide the best sensitivity to weak signals, while keeping the receiver quiet when no signal is received. The LED just above the Main Dial will glow Green
when the squelch is opened by an incoming signal or noise.
Battery consumption is significantly reduced if the receiver is squelched, as the
audio amplifier stage is shut off when the receiver is muted.
20
FT-817ND Operating Manual
OPERATION
SETTING THE OPERATING FREQUENCY
1. In the “SSB/CW/DIG” modes, rotate the
knob to set the frequency. Clockwise
rotation of the
knob increases the operating frequency.
2. In the “AM/FM/PKT” modes, rotate the
knob to set the frequency. Clockwise rotation of the
knob increases the operating
frequency.
3. You may also use the
knob to adjust the operating frequency in the “SSB/CW/
DIG” modes. The
knob provides faster tuning, ideal for making quick changes in
frequency when you want to move across the band in a hurry. You can then use the
knob to make fine frequency adjustments.
4. If you press the
knob momentarily, then rotate the
knob, you can now change
the operating frequency in 1 MHz steps, allowing very quick frequency excursions. This
can be particularly helpful on the VHF and UHF bands.
5. In step 2 above, it was mentioned that tuning in the “AM/FM/PKT” modes is accomplished using the
knob. By default, the
knob is disabled in these modes; if
you wish to enable the
knob in these modes, use Menu #04; see page 60.
6. The synthesizer steps for the
knob may be adjusted independently by mode. Use
Menu #06 for AM, #30 for FM, and #47 for SSB/CW/Digital. See pages 60, 64, and 67
for details.
The main
of the
knob synthesizer’s tuning rate (the number of steps per rotation
knob) can be adjusted using Menu #33. See page 65 for details.
STACKED VFO SYSTEM
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 1 [A/B, A=B, SPL] appears on the display.
(A/B) key to toggle between the “A” and “B” VFOs. There are two
2. Now press the
such VFOs provided on each Amateur band, so you may set VFO-A to the CW sub-band,
and VFO-B to the SSB sub-band, if you like. The operating mode will be preserved,
along with the frequency information, on each VFO.
FT-817ND Operating Manual
21
OPERATION
OPERATION ON 5 MHZ BAND (U.S. VERSION ONLY)
The FT-817ND includes the capability for transmission and reception on the five spot frequencies assigned to the Amateur Service in the United States. To operate on the 5 MHz
band:
key once to enter the “Memory”
1. Press the
mode (a memory channel number “M-nnn”
will appear on the display in the space previously occupied by “VFOa” or “VFOb”).
2. Memory channels “M-601” through “M-605”
are pre-programmed, at the factory, with the
SEL
permitted frequencies in the 5 MHz band, and the USB mode is
automatically selected on these channels.
If you have partitioned your memory channels into Memory
Groups via Menu #34, the memory channel numbers for 60meter operation will be displayed as “l - 001” ~ “l - 005.” See
page 46 for details regarding Memory Group operation, and
page 65 for details regarding Menu #34.
3. To exit from 60-meter operatin and return to the VFO mode,
just press the
key (the memory channel number will be
replaced by “VFOa” or “VFOb”).
V/M
F
VM
SE L
LOCK
AF
PWR
SQL/RF
CLAR
The frequencies and operating mode for 5 MHz band operation are both fixed, and may not be changed.
[Memory Group “OFF”]
[Memory Group “ON”]
CH No.
M - 601
M - 602
M - 603
M - 604
M - 605
FREQUENCY
5.332 MHz
5.348 MHz
5.368 MHz
5.373 MHz
5.405 MHz
Downloaded by
RadioAmateur.EU
22
FT-817ND Operating Manual
RECEIVER ACCESSORIES
CLARIFIER (RECEIVER INCREMENTAL TUNING)
The Clarifier (RIT) allows you to set an offset of up to &plusmn;9.99 kHz of the receive frequency
relative to your transmit frequency. To achieve a wider offset than this, you may use the
“Split” operating mode, described later.
switch momentarily to activate
1. Press the
the Clarifier function.
2. Turn the
knob, which allows the receiver frequency to be varied over a range of
9.99 kHz.
3. When the receiving frequency is higher than
transmit frequency, the “ ” icon will appear at the right of the
frequency display. Similarly, when the receiving frequency is
lower than transmit frequency, the “ ” icon will appear at the
right of the frequency display.
4. When the receiving frequency is equal to transmit frequency
(Clarifier offset is zero) while the Clarifier is activated, the “ ”
icon will appear at the right of the frequency display.
5. To turn the Clarifier off, again press the
switch momentarily. When you turn the Clarifier back on, the offset previously
stored will still be applied.
6. To reset the Clarifier offset to zero, turn the Clarifier off, then
turn the
knob by any amount. The Clarifier will reset to
zero after the first “step” of the
knob.
If you leave the Clarifier on, moving the
cancelled.
FT-817ND Operating Manual
[TX&lt;RX]
[TX&gt;RX]
[TX=RX]
knob will not cause the offset to be
23
RECEIVER ACCESSORIES
IF SHIFT
The receiver’s IF SHIFT feature is an effective interference-reduction tool, which allows
you to shift the passband response higher or lower without changing the pitch of the incoming signal.
switch for one second to acti1. Press the
vate the IF SHIFT feature. A “ ”, “ ,” or
“ ” icon will appear at the right of the frequency display to indicate the IF SHIFT’s
current position.
2. Rotate the
knob, as needed, to reduce
or eliminate the interference.
3. To turn the IF SHIFT feature off, again press the
switch for
one second. The last setting of the IF SHIFT control will be
retained until you change it again.
4. If you wish to make a more permanent shift in the receiver’s IF
passband, use Menu #54 (LSB) or #55 (USB) in the “Extended
Menu.” This allows you to set up a higher or lower listening
pitch, if you prefer such as compared to the default passband
response. See page 68.
Engaging of the IF Shift feature does not disable the setting of the Clarifier control. With the IF Shift activated,
press the
switch momentarily to switch to Clarifier operation.
24
FT-817ND Operating Manual
RECEIVER ACCESSORIES
AGC (AUTOMATIC GAIN CONTROL)
The receiver recovery time constant of the AGC system may be modified to match your
operating needs.
key momentarily, then rotate the
knob, as needed, until Operating
1. Press the
Function Row 8 [NB, AGC] appears on the display.
(AGC) key to toggle the AGC recovery time constant among the following
2. Press the
selections:
“AGCauto” “AGCfast” “AGCslow” “AGCoff” “AGCauto” ……
where “AGCauto” represents “AGCfast” on CW and DIG(AFSK), and “AGCslow” on
the voice modes.
If “AGCoff” selected, the S-meter (which monitors AGC voltage) will cease to function.
NOISE BLANKER
The IF Noise Blanker may be useful in reducing or eliminating some types of impulse noise,
especially noise generated by automotive ignition systems.
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 8 [NB, AGC] appears on the display.
(NB) key to activate the Noise Blanker. The “” icon will appear at the
2. Press the
right of the “NB” indication.
(NB) key again to turn the Noise Blanker off.
3. Press the
IPO (INTERCEPT POINT OPTIMIZATION)
The IPO feature bypasses the receiver RF preamplifier, thereby eliminating the preamp’s
gain. This feature is not available on the 144 MHz and 430 MHz.
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 7 [IPO, ATT, NAR] appears on the display.
(IPO) key to bypass the receiver input preamplifier. The “” icon will
2. Press the
appear at the right of the “IPO” indication.
(IPO) key once more to re-activate the preamp.
3. Press the
On the bands below 14 MHz, the input preamplifier is rarely necessary, and activation of the IPO feature will provide substantial protection against intermodulation
and other problems associated with strong signal input to the receiver. Rule of thumb: so
long as the S-meter is moving on background noise, additional front-end gain is not
necessary.
FT-817ND Operating Manual
25
RECEIVER ACCESSORIES
ATT (FRONT END ATTENUATOR)
The Attenuator will reduce all signals (and noise) by 10 dB, and it may be used to make
reception more pleasant under extremely noisy conditions. This feature is not available on
the 144 MHz and 430 MHz.
key momentarily, then rotate the
knob, as needed, until Operating
1. Press the
[
]
Function Row 7 IPO, ATT, NAR appears on the display.
(ATT) key to activate the Attenuator. The “” icon will appear at the right
2. Press the
of the “ATT” indication.
(ATT) key once more to switch the Attenuator out of the receiver front end
3. Press the
circuit.
AM/FM DIAL
In the AM and FM modes, the
knob is locked out (via the setting of Menu #04) so as
to allow “channelized” tuning on these modes. To adjust the operating frequency, rotate the
knob.
knob for tuning in the AM and FM modes, change the setting
If you wish to enable the
of Menu #04. See page 60 for details.
The “channelized” mode of tuning on AM and FM automatically rounds off the
frequency to the next “logical” step when you rotate the
knob one “click” in
either direction. This eliminates the inconvenience of having to preset the frequency to
an “even” channel.
26
FT-817ND Operating Manual
RECEIVER ACCESSORIES
AUTOMATIC POWER-OFF FEATURE
The APO feature helps conserve battery life by automatically turning the transceiver off
after a user-defined period of time within which there has been no dial or key activity. The
available selections for the time before power-off are 1 ~ 6 hours, as well as “APO Off.” The
default condition for the APO is OFF, and here is the procedure for activating it:
key for one second to enter the Menu mode.
1. Press and hold the
2. Rotate the
knob to recall Menu #08 (APO TIME).
3. Rotate the
knob to select the desired time period after which the radio will automatically shut down.
4. Press and hold the
key for one second to save the new setting and exit to normal
operation.
Once you have programmed a time interval, the APO countdown timer will start whenever
some front panel action (tuning, transmission, etc.) is completed.
When the APO is activated, the “ ” icon will appear at the center bottom on the LCD. If
there is no action by you within the time interval programmed, the microprocessor will shut
down the radio automatically.
Just press and hold in the
APO shutdown, as usual.
switch for one second to turn the transceiver back on after an
FT-817ND Operating Manual
27
TRANSMITTER OPERATION
SSB TRANSMISSION
Basic Setup/Operation
1. Press the
/
key so as to select either SSB (LSB/USB) mode. If you
are operating on the 7 MHz or lower bands, select the LSB mode. If you are operating on
the 14 MHz or higher bands, select the USB mode.
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
(MTR) key to
Function Row 9 [PWR, MTR] appears on the display, then press the
select the “ALC” meter function (“alc” will appear at the right side of the “MTR” icon).
3. Press the microphone’s PTT switch, and speak into the microphone in a normal voice
while watching the meter. The ideal audio input level to the transmitter from the microphone will cause a few “segments” of indication on the ALC meter. Release the PTT
switch to return to receive mode.
4. If the ALC meter is too high, or too low, you may need to reset the Microphone Gain:
key for one second to enter the Menu mode.
Press and hold in the
knob to recall Menu #46 (SSB MIC).
Rotate the
Close the PTT switch, and while speaking into the microphone rotate the
knob until the proper ALC indication is achieved on voice peaks.
When done, press and hold in the key to save the new setting for the Microphone Gain.
The [TONE] switch on the back of the MH-31A8J microphone provides adjustment of the microphone’s frequency response. Setting this switch to the “2” position will roll off some of the bass response, resulting in improved “talk power” in many
instances. The “1” position is primarily used in countries like Japan, where vowel sounds
are of critical importance in conveying information; in Western languages, consonant
sounds (which are rich in high-frequency components) are frequently more important.
Adjusting the Transmitter Power Output
Four power levels are available on the FT-817ND: 5 Watts, 2.5 Watts, 1 Watt, and
0.5 Watt. When using Alkaline batteries or the supplied FNB-85 Ni-MH Battery
Pack, the microprocessor, detecting internal battery use, automatically sets the power
level to 2.5 Watts, which appears on the display as “ ”. If you set the power to five
watts, the power level icon is the same as for 2.5 Watt operation, but at 5 Watts the
icon is blinking. For 0.5 Watt, there is one “bar” to the right of the “L” in the power
icon, and for 1 Watt there are two “bars” displayed.
The power level is easy to change:
1. Press the
key momentarily, then rotate the
knob to select Operating
Function Row 9 [PWR, MTR].
(PWR) key, as needed, to set the desired power level. The icon will
2. Press the
change, based on the power level you have set.
28
FT-817ND Operating Manual
TRANSMITTER OPERATION
SSB TRANSMISSION
VOX Operation
The VOX system provides automatic transmit/receive switching based on voice input to the
microphone. With the VOX system enabled, you do not need to press the PTT switch in
order to transmit.
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 10 [VOX, BK, KYR] appears on the display.
(VOX) key to activate the VOX circuitry. The “” icon will appear at the
2. Press the
right of the “VOX” indication.
3. Without pressing the PTT switch, speak into the microphone in a normal voice level.
When you start speaking, the transmitter should be activated automatically. When you
finish speaking, the transceiver should return to the receive mode (after a short delay).
(VOX) key. The “”
4. To cancel VOX and return to PTT operation., again press the
icon will disappear.
5. The VOX Gain may be adjusted, so as to prevent accidental transmitter activation in a
noisy environment. To adjust the VOX Gain:
(VOX)
While still in Operating Row 10 [VOX, BK, KYR], press and hold in the
key for one second. This is a “hot key” feature which will instantly recall Menu #51
(VOX GAIN).
knob to the point where the
While speaking into the microphone, rotate the
transmitter is quickly activated by your voice, without causing background noise to
activate the transmitter.
key for one
When you have selected the optimum setting, press and hold the
second to save the new settings and return to normal operation.
6. The “Hang-Time” of the VOX system (the transmit-receive delay after the cessation of
speech) may also be adjusted via the Menu. The default delay is 1/2 second. To set a
different delay time:
key for one second to activate the Menu mode.
Press and hold in the
knob to select Menu #50 (VOX DELAY).
Rotate the
knob while saying a brief syllable like “Ah” so as to set the desired
Rotate the
delay time.
When your adjustments are complete, press and hold in the key for one second to
save the new setting and return to normal operation.
The delay time for return to the receive mode is set independently on CW and voice
modes; for CW, use Menu #17 (see next section).
FT-817ND Operating Manual
29
TRANSMITTER OPERATION
CW TRANSMISSION
Operation using Straight Key/External Keying Device
When using a straight key, an external electronic keyer, or a computer-generated keying
device, please follow the instructions in this section.
1. Insert your key’s (three-conductor) plug into the rear-panel KEY jack.
2. Press the
/
key, as needed, to select one of the CW (CW/CWR)
modes.
The “CW” mode utilizes USB-side carrier injection, while the CWR (Reverse)
mode utilizes LSB-side injection.
3. Press the
key momentarily, then then rotate the
knob, as needed, until Operating Function Row 10 [VOX, BK, KYR] appears on the display.
(BK) key, as needed, to activate “Semi Break-In” operation. The “” icon
4. Press the
will appear at the right of the “BK” indication.
5. The CW hang time can be adjusted using Menu #17 (CW DELAY). To adjust the CW
hang time:
key for one second to enter the Menu mode.
Press and hold in the
knob to select Menu #17 (CW DELAY).
Rotate the
knob to select a longer or shorter delay time (default: 250 ms). This
Rotate the
transceiver was not expressly designed for “full QSK” operation, the minimum (10
ms) setting of this Menu item (CW DELAY) will be very close to full break-in performance.
key for one second to save the new setting and
When done, press and hold in the
exit to normal operation.
If you are already in Operating Function Row 10 [VOX, BK, KYR], pressing
(BK) key for one second will instantly select Menu #17
and holding in the
(CW DELAY).
(BK) key to make the
6. To practice your CW sending (without transmitting), press the
“” icon disappear. Now, pressing the key will cause the CW sidetone to be heard, but
your radio will not be transmitting a signal on the air.
7. You can adjust the CW sidetone volume level via Menu #44 (SIDETONE). To adjust the
CW sidetone volume level:
key for one second to enter the Menu mode.
Press and hold in the
knob to select Menu #44 (SIDETONE).
Rotate the
knob to select a new level; on the arbitrary scale of “0” ~ “100,” the
Rotate the
default value is “50.”
key for one second to save the new setting and
When done, press and hold in the
exit to normal operation.
30
FT-817ND Operating Manual
TRANSMITTER OPERATION
CW TRANSMISSION
8. You also can adjust the CW sidetone pitch using Menu #20 (CW PITCH). This adjustment also controls the BFO offset (actual pitch of your transmitted signal relative to your
current receive frequency). To adjust the CW sidetone pitch:
key for one second to enter the Menu mode.
Press and hold in the
knob to select Menu #20 (CW PITCH).
Rotate the
knob to select a new pitch tone/BFO offset. The available offset
Rotate the
range is 300 ~ 1000 Hz (default value is “700 Hz”).
key for one second to save the new setting and
When done, press and hold in the
exit to normal operation.
Because the CW Pitch corresponds to the actual pitch of your transmitted signal,
the sidetone may be used in a “CW Spot” capacity. Just tune the pitch of the received signal to the same pitch as that of your transceiver’s sidetone, and you will be
perfectly “zero beat” with the other station.
The FT-817ND can generate a “CW Spot” tone; just press and hold in the
key while
in the CW mode.
FT-817ND Operating Manual
31
TRANSMITTER OPERATION
CW TRANSMISSION
Operation using Built-in Electronic Keyer
The built-in Electronic Keyer provides a convenient method of generating CW. The Electronic Keyer includes weight and speed adjustments.
1. Connect your keyer paddle’s cable to the KEY jack on the rear panel of the transceiver.
2. Press the
/
key, as needed, to select the CW (CW/CWR) mode.
3. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 10 [VOX, BK, KYR] appears on the display.
(KYR) key to activate the Electronic Keyer. The “” icon will appear at
4. Press the
the right of the “KYR” indication.
5. The Keyer speed may be adjusted using Menu #21 (CW SPEED). To adjust the Keyer
speed:
key for one second to enter the Menu mode.
Press and hold in the
knob to select Menu #21 (CW SPEED).
Rotate the
knob if you wish to select display of “cpm” (characters per minute)
Press the
instead of “wpm” (words per minute). The “cpm” selection is based on the international “PARIS” standard, which stipulates five characters per word.
knob, while sending, to set the desired sending speed.
Rotate the
key for one second to save the new setting and
When done, press and hold in the
exit to normal operation.
If you are already using Operating Function Row 10 [VOX, BK, KYR], press
and hold in the [C](KYR) key to switch instantly to Menu #21 (CW SPEED).
6. The Dot:Dash weighting ratio may be adjusted via Menu #22 (CW WEIGHT). To adjust
the Dot:Dash weighting ratio:
key for one second to enter
Press and hold in the
the Menu mode.
knob to select Menu #22 (CW
Rotate the
WEIGHT).
knob to set the desired weight.
Rotate the
key for one sec When done, press and hold in the
ond to save the new setting and exit to normal operation.
7. You may select “normal” or “reverse” paddle polarity via Menu #19 (CW PADDLE).
The default setting for this feature is “normal,” whereby the “Tip” connection on the
Key Plug is “Dot” and the “Ring” connection is “Dash.” To change the paddle polarity:
key for one second to enter the Menu mode.
Press and hold in the
knob to select Menu #19 (CW PADDLE).
Rotate the
knob to select the new setting.
Rotate the
key for one second to save the new setting and
When done, press and hold in the
exit to normal operation.
32
FT-817ND Operating Manual
TRANSMITTER OPERATION
FM TRANSMISSION
Basic Setup/Operation
1.
2.
3.
4.
Press the
/
key so as to select the FM mode.
Press the microphone’s PTT switch, and speak into the microphone in a normal voice.
Release the PTT switch to return to the receive mode.
If you get reports that your modulation level is too high or too low, you may need to
adjust the FM-mode microphone gain. The procedure is similar to that used on SSB:
key momentarily, then rotate the
knob, as needed, until Operat Press the
(MTR)
ing Function Row 9 [PWR, MTR] appears on the display, then press the
key to select the “Deviation” meter function (“mod” will appear at the right side of
the “MTR” icon).
key for one second to enter the Menu mode.
Press and hold in the
Rotate
the
knob
to
recall Menu #29 (FM MIC).
Increase or decrease the setting of the FM Mic Gain, depending on the level correction required, then press and hold the
key to save the new setting.
Close the PTT switch, and while speaking into the microphone observe the meter
indication; the proper setting of the FM Mic Gain will produce five “bars” of indication on voice peaks, slightly less on lower levels of speech input.
key to save the new setting for the FM-mode
When done, press and hold in the
microphone gain.
5. The VOX feature is operational during FM transmission. From Operating Function Row
(VOX) key to activate/deactivate VOX.
10 [VOX, BK, KYR], press the
Repeater Operation
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 4 [RPT, REV, TON] appears on the display.
(RPT) key to activate repeater operation. One press of the
(RPT) key
2. Press the
will have set the transceiver for “Minus Shift” operation. In this situation, you will observe the “–” indicator on the display. The transmitter frequency will be shifted down by
a default value so as to access the repeater input frequency. If your repeater uses a posi(RPT) key again; the “+” indicator will
tive shift (instead of negative), press the
replace the “–” indicator on the display.
3. If the default repeater shift is not appropriate for your area, it may be set independently
for each band. To change the repeater shifts:
(RPT) key for one second. This instantly recalls Menu #42
Press and hold the
(RPT SHFT).
knob to select the desired shift frequency.
Rotate the
key for one second to save the new setting and
When done, press and hold in the
exit to normal operation.
FT-817ND Operating Manual
33
TRANSMITTER OPERATION
FM TRANSMISSION
(TON) key to activate the CTCSS tone encoder, which provides a subaudible
4. Press the
(TON) key will activate the CTCSS tone
repeater access tone. One press of the
encoder. In this situation, you will observe the “ ” indicator on the display. If you press
(TON) key repeatedly, you will observe “
the
” (CTCSS Encode/Decode),
followed by “
” (Digital Coded Squelch, Encode/Decode). One additional press
will disable all repeater-access tone systems. See the next section for a discussion of
DCS operation.
5. If the default repeater access tone are not appropriate for your area, it also may be set
independently for each band. To change the repeater access tone:
(TON) key for one second. This instantly recalls Menu #48
Press and hold the
(TONE FREQ).
knob to select the desired CTCSS frequency.
Rotate the
key for one second so save the new setting and
When done, press and hold the
exit to normal operation.
6. Set the transceiver’s receiver to the repeater output (downlink) frequency.
7. Close the PTT switch and speak into the microphone. You will observe that the transmit(RPT) key.
ted frequency has shifted according to the setting of the
8. Release the PTT switch to return to the Receive mode.
9. With repeater shift activated, you can temporarily reverse the transmit and receive fre(REV) key. The “ ” icon will blink while “Reverse” shift
quencies by pressing the
(REV) key again to revert to the “Normal” shift direction.
is activated. Press the
10. When you are finished with repeater operation, you may wish to set the repeater shift to
(RPT) key, and disable the CTCSS or DCS tone by presssimplex by pressing the
(
)
ing the
TON key.
11. On many transceiver versions, the Automatic Repeater Shift (ARS) feature is enabled at
the factory. This feature automatically activates the appropriate repeater shift when you
are operating inside the designated 144 MHz or 430 MHz FM repeater sub-bands in
your country. If you wish to change the settings for the ARS, use Menu #01 (144 ARS)
or Menu #02 (430 ARS) (see page 60).
If your local repeaters need a 1750-Hz burst tone for access (typically in Europe),
press and hold in the front panel’s
key to transmit the burst tone.
34
FT-817ND Operating Manual
TRANSMITTER OPERATION
FM TRANSMISSION
Tone Search Scanning
In operating situations where you don’t know the CTCSS tone being used by another
station, you can command the radio to listen to the incoming signal and scan in search
of the tone being used.
To scan for the CTCSS tone in use:
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating Function Row 12 [TCH, DCH] appears on the display.
(TCH) key to activate CTCSS Encoder/Decoder; (the “
2. Press the
”
icon will appear on the display) and start scanning for the incoming CTCSS tone.
3. When the radio detects the correct tone, it will halt on that tone, and audio will be
allowed to pass.
(TCH) key for one second; the CTCSS tone detected
4. Press and hold in the
will be stored as the “current” tone, so it may be used for memory storage purposes, and you may now exit to normal operation.
FT-817ND Operating Manual
35
TRANSMITTER OPERATION
FM TRANSMISSION
DCS Operation
Another form of tone access control is Digital Code Squelch, or DCS. It is a newer, more
advanced tone system that is less susceptible to false triggering than CTCSS. A DCS Encoder/Decoder is built into your transceiver, and operation is very similar to that described
above for CTCSS.
1. Set the desired DCS code via Menu #23 (DCS CODE).
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 4 [RPT, REV, TON] appears on the display.
(TON) key three times to activate the DCS Encoder/Decoder (the “
3. Press the
”
icon will appear on the display). The receiver will remain muted until a matching DCS
code is received on an incoming signal.
(TON) key once to cancel DCS operation (the “
4. Press the
” icon will disappear).
DSC Search Scanning
In operating situations where you don’t know the DCS code being used by another
station, you can command the radio to listen to the incoming signal and scan in search
of the code being used.
To scan for the DCS code in use:
1. Press the
key momentarily, then rotate the
knob, as needed, until Oper[
]
ating Function Row 12 TCH, DCH appears on the display.
(DCH) key to activate DCS Encoder/Decoder; (the “
2. Press the
” icon
will appear on the display) and start scanning for the incoming DCS code.
3. When the radio detects the correct code, it will halt on that code, and audio will
be allowed to pass.
4. Press and hold in the
(DCH) key for one second; the DCS code detected will
be stored as the “current” code, so it may be used for memory storage purposes,
and you may now exit to normal operation.
36
FT-817ND Operating Manual
TRANSMITTER OPERATION
FM TRANSMISSION
ARTS
TM
(AUTO RANGE TRANSPOND SYSTEM) Operation
The ARTSTM system uses DCS signaling to inform you when you and another ARTS™-equipped
station are within communications range. This can be especially valuable during search-andrescue operations, as a base station can quickly use ARTS™ to alert a field unit that it is out of
range; the field unit can then move to a better location to re-establish communications.
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 6 [SSM, SCH, ART] appears on the display.
(ART) key to activate ARTS™ operation.
2. Press the
3. Your display will change to “out range” to indicate the beginning of ARTS™ operation. Every 25 seconds, your radio will
transmit a “polling” call to the other station. When that station
responds with its return ARTS™ polling signal, your display
will change to “in range” to confirm reception of the response.
( ART ) key again (the “out range” or
4. To cancel ARTS operation, press the
“in range” indication will disappear from the LCD).
The ARTS™ feature offers a choice of beep options to alert you to the current
status of ARTS™ operation. Use MENU #09 (ARTS BEEP) on page 61 to select the
beep option that is best for your operating needs.
CW Identifier Setup
The ARTS™ feature includes a CW identifier. When it is activated, the radio will send “DE
(your callsign) K” in Morse code every ten minutes during ARTS™ operation.
To program the CW IDer, use Menu #31 (ID), as described on page 64. And to activate the
CW IDer, use Menu #18 (CW ID).
FT-817ND Operating Manual
37
TRANSMITTER OPERATION
DIGITAL MODE OPERATION (SSB-BASED AFSK)
The FT-817ND provides extensive capability for digital mode operation on the HF, VHF,
and UHF bands. The use of AFSK (Audio Frequency-Shifted Keying) configurations allows
a wide variety of different communication modes to be utilized. The Menu provides for
specific digital mode selections, which include custom BFO offsets to optimize the receive
and transmit passbands for the mode selected.
Before beginning Digital operation, you need to define which Digital mode will be utilized.
To do this, use Menu #26 as follows (in this example, we will set up RTTY as the Digital
mode):
1.
2.
3.
4.
key for one second to enter the Menu mode.
Press and hold in the
Rotate the
knob to select Menu #26 (DIG MODE).
Rotate the
knob to select “RTTY.”
Press and hold in the
key for one second to save the new setting and exit.
Use this technique to set up any digital mode.
RTTY (Radio TeleType) Operation
The “RTTY” mode on the FT-817ND is based on LSB-side carrier injection, in accordance
with long-standing amateur practice. If you need USB-side injection for your application,
see the “User” mode discussion below.
1. Connect your TNC (Terminal Node Controller) or terminal modem to the FT-817ND’s
rear-panel DATA jack, per the illustration.
2. Press the
/
key, as needed, to select the DIG mode (the “DIG” icon
will appear on the display). Be certain to use the “TX Audio” line from your TNC, not an
“FSK Key” line, for the transmit-data connection.
3. Press the
/
key, as needed, to select the DIG mode (the “DIG” icon
will appear on the display). You should now be able to tune around the band, and any
RTTY signals heard should be capable of being decoded.
Pin
1
Label
DATA IN
2
3
PTT
–
4
5
38
Note
Maximum Input Lebel
1.0 V pp
Impedance: 10 kΩ
Ground to Transmit
–
DATA OUT Maximum Output Level: 300 mVpp
Impedance 10kΩ
–
–
FT-817ND Operating Manual
TRANSMITTER OPERATION
DIGITAL MODE OPERATION (SSB-BASED AFSK)
4. If the optional YF-122C 500 Hz filter has been installed, it may be used for RTTY work.
(NAR) key to
Recall Operating Function Row 7 [IPO, ATT, NAR] then press the
engage the narrow filter.
5. To set up the transmit side, be sure that the Meter is set to monitor ALC voltage. If not,
key momentarily, then rotate the
knob to select to select Operating
press the
(MTR) key so as to select metering of
Function Row 9 [PWR, MTR], then press the
ALC.
key for 1/2 second to enter the MENU mode, then rotate the
6. Press and hold in the
knob to select Menu #25 (DIG MIC).
7. Following the instructions for your TNC’s software, activate the transmitter from the
computer keyboard; this should cause the AFSK output from the TNC to be sent to the
radio. While transmitting, view the ALC meter; a few “dots” of ALC indication should
be observed. If not, rotate the
knob to adjust the AFSK level. Press and hold in the
key for one second to save the new AFSK level setting and return to normal operation. You are now ready for RTTY operation.
Because RTTY is a continuous-duty transmission mode, try to keep your transmission
short when running on battery power, so as to minimize current drain.
PSK31 Operation
Two dedicated PSK31 modes are available, one each for USB-side and LSB-side injection.
For BPSK work, the injection does not matter, but for QPSK the two working stations must
use the same sideband.
Connect the FT-817ND to your computer’s sound card or interface.
Setup for PSK31 operation is basically identical to that previously described for RTTY
operation. As before, use the “DIG” mode. However, in Menu #26, select “PSK31-L” (for
LSB injection) or “PSK31-U” (for USB injection. As with RTTY, Menu #25 may be used to
set the drive to the transmitter. And the YF-122C 500 Hz filter may also be utilized, as
described previously.
FT-817ND Operating Manual
39
TRANSMITTER OPERATION
DIGITAL MODE OPERATION (SSB-BASED AFSK)
“USER” Defined Digital Modes
Also provided in the FT-817ND are two convenient “USER” Digital modes, one each providing USB- and LSB-side injection, which may be used for SSTV, Fax, Pactor, and other
digital operating modes.
Here is an example involving the configuration of the USER mode for RTTY with USB-side
injection (as opposed to LSB injection, used in the default “RTTY” mode):
1. Use Menu #26 to set the Digital mode to “USER-U.”
2. Press the
/
key, as needed, to select the DIG mode (the “DIG” icon
will appear on the display).
3. Now use Menu #27 to configure the transceiver’s passband response. Once in the Menu
mode, rotate the
knob to select Menu #27 (DIG SHIFT), and rotate the
knob
to set the desired BFO offset (depending on how your TNC’s tones are set up). For
typical high-frequency tone use, a setting of about “+2100” will be a good starting
point.
4. Finally, depending on how you wish the display to respond, you may program in a corresponding display shift, using Menu #24 (DIG DISP). Remember to press and hold in the
key for one second when exiting the Menu mode.
5. The setup of the AFSK drive level is identical to that described previously for RTTY
operation.
The USER-L and USER-U Digital modes should allow you to operate on any SSBbased AFSK Digital mode. Note that the “PSK31” configurations will also work
well for many Digital operating situations.
40
FT-817ND Operating Manual
TRANSMITTER OPERATION
PACKET (1200/9600 BPS FM) OPERATION
The FT-817ND is designed for operation on either 1200 bps or 9600 bps packet, and setup is
similar to that described previously for SSB-based modes. A separate Data input adjustment
is provided, allowing you to optimize the deviation on the FM Packet modes separately
from the SSB-based Digital modes. The RX-Data output lines are fixed-level outputs, not
affected by the setting of the AF Gain control.
1. Connect your TNC to the FT-817ND’s rear-panel DATA jack, per the illustration. Note
that different connections are used for 1200 bps and 9600 bps Packet.
2. Use Menu #40 (PKT RATE) to select the desired Packet mode. Once you have entered
the Menu and have selected Menu #40, rotate the
knob to select either “1200” or
“9600” (bps) as the Packet rate.
3. Press the
/
key, as needed, to select the PKT mode (the “PKT” icon
will appear on the display).
4. You are now set up for reception on Packet. If you are operating on 1200 bps, try now to
connect to another station or node; you may well find that the drive level needs no further adjustment.
5. If you are having trouble connecting due to insufficient or excessive drive from the TNC
to the FT-817ND, use Menu #39 (PKT MIC) to set the drive. Use your terminal software’s
“test” protocol to send out test tones, and adjust the deviation by rotating the
knob, which will vary the data input level to the FT-817ND’s modulator. Remember to
press and hold in the
key for one second when adjustments are completed, so as to
save the new setting for Menu #39.
The 9600 bps Packet deviation setting is very critical to successful operation, and
it can only be accomplished using a calibrated deviation meter; the optimum setting is usually &plusmn;2.75 kHz (&plusmn;0.25 kHz). For 1200 bps, the optimum level is much less
critical, with the optimum deviation being between &plusmn;2.5 kHz and &plusmn;3.5 kHz.
Pin
1
2
3
4
5
Label
DATA IN
Note
Maximum Input Lebel
40 mV pp @1200 bps
1.0 V pp @9600bps
Impedance: 10 kΩ
PTT
Ground to Transmit
DATA OUT Maximum Output Level: 500 mVpp
9600 bps Impedance 10kΩ
DATA OUT Maximum Output Level: 300 mVpp
1200 bps Impedance 10kΩ
SQL
SQL Open: +5V
SQL Closed: 0V
FT-817ND Operating Manual
41
TRANSMITTER OPERATION
AM TRANSMISSION
The FT-817ND utilizes low-level amplitude modulation of an early stage for transmission
purposes. This capability is primarily provided for emergency use only, as low-power operation typically utilizes more efficient transmission/reception modes.
The AM carrier level is preset to 1.5 Watts during alignment at the factory, and should not
require further adjustment. It is important to remember that AM transmission requires that
power must be distributed among the carrier and voice sidebands; therefore, if excessive
carrier power is used, there will be insufficient power available for the information-carrying
voice sidebands.
The AM microphone gain is preset at the factory to a value which typically provides good
audio. If you need to modify the microphone gain in the AM mode, use Menu #05 (AM
MIC). See page 60 for details.
SPLIT FREQUENCY OPERATION
This transceiver provides convenient split-frequency operation, using the VFO-A and VFOB, for DX working and other operating situations requiring unique split frequency pairs.
The example below will describe a typical split-frequency DX situation on the 20-meter
band, with a DX station transmitting on 14.025 MHz, listening 10 kHz higher in the band.
1. Set VFO-A to 14.035.00 MHz CW (DX station’s listening frequency).
key momentarily, then rotate the
knob, as needed, until Operating
2. Press the
Function Row [A/B, A=B, SPL].
(A/B) key momentarily to select VFO-B.
3. Press the
4. Tune the VFO-B frequency to 14.025.00 MHz (DX station’s transmitting frequency).
(SPL) key momentarily. The transceiver will now transmit using the VFO5. Press the
A frequency, and will receive using the VFO-B frequency. The “
” icon will appear
on the display.
6. To listen to the pile-up calling the DX station (so as to align your frequency more closely
(A/B) key to reverse the
to that of the station being worked by the DX), press the
VFOs. You will now be tuning in the vicinity of 14.035 MHz, and you can zero in on the
DX station’s listening frequency by tuning in on the station in QSO with the DX. Press
(A/B) key again to return to reception on the DX station’s frequency.
the
(SPL) key once more to cancel split operation; the “
7. Press the
” icon will disappear from the display.
42
FT-817ND Operating Manual
TRANSMITTER OPERATION
TIME-OUT TIMER
Most often used on FM, the transmitter’s Time-Out Timer (TOT) feature disables the transmitter after a user-defined period of transmission. This feature may be useful in preventing
a “stuck microphone” (accidental closure of the PTT switch) from causing interference to
other users, and it will also force you to keep your transmission short, thereby conserving
battery power.
To activate the Time-Out Timer:
key for one second to enter the Menu mode.
1. Press and hold in the
2. Rotate the
knob to recall Menu #49 (TOT TIME).
3. The default setting for this feature is “off.” Rotate the
knob to set a new time-out
setting (from 1 minute to 20 minutes).
4. When you have made your selection, press and hold in the
key for one second to save
the new setting and exit to normal operation.
WEATHERFAX MONITORING
Monitoring of HF WeatherFax broadcasts is easily accomplished using the FT-817ND.
1. Before proceeding, be certain that the WeatherFax demodulator is properly connected to
Pins 5 (DATA OUT 1200bps) and 2 (GND) of the rear panel DATA jack.
2. Set the transceiver to the VFO mode, and set the operating mode to “DIG,” setting Menu
#26 to PSK31-U, as described previously.
3. Now, select the operating frequency of the station transmitting the WeatherFax broadcast. Note that, in the USB mode, the frequency you should program onto the display is
typically 1.90 kHz below the station’s “assigned” frequency. Thus for a WeatherFax
station assigned to 8.682.0 MHz, tune to 8.680.1 MHz.
4. When the WeatherFax broadcast begins, no further operator intervention should be needed
from the transceiver standpoint. The audio level from the DATA jack on the rear of the
transceiver is fixed, and cannot be adjusted.
Fine adjustments in the gray-scale and the frame alignment are accomplished using the computer and software connected to your WeatherFax demodulator.
FT-817ND Operating Manual
43
MEMORY OPERATION
QMB CHANNEL
QMB Channel Storage
1. Tune in the desired frequency and set the operating mode and bandwidth. If this is an FM
channel, set up any required CTCSS/DCS and repeater shift configurations.
2. Press and hold in the
key until a double “beep” is heard. The second beep provides
audible confirmation that the data has been stored into the QMB memory.
(A/B) key momentarily while in Operating Function Row 3 [STO,
Pressing the
RCL, PMS] will also store a frequency into the QMB register.
QMB Channel Recall
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 3 [STO, RCL, PMS] appears on the display.
(RCL) key momentarily to recall the QMB memory. “QMB” will appear at
2. Press the
the upper right corner on the LCD.
(RCL) key once more to return to the previous frequency (either a VFO
3. Press the
frequency or a Memory channel).
If you move the
knob or
knob while in the QMB mode, you can
change frequencies as if you were in a “VFO” mode. You also can change operating mode by pressing the
or
key. When this is done, the “MTQMB”
(RCL)
will appear in the display, where “MT” represents “Memory Tuning.” Press the
key once more to return to the originally-stored QMB frequency.
44
FT-817ND Operating Manual
MEMORY OPERATION
MEMORY OPERATION ON “REGULAR•EMEMORY CHANNELS
Normal Memory Storage
1. Tune in the desired frequency, and set the operating mode and bandwidth. If this is an
FM channel, set up any required CTCSS/DCS and repeater shift configurations. Standard (default) repeater shifts do not require you to utilize the “split” frequency memory
technique, described later.
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 2 [MW, MC, TAG] appears on the display.
(MW) key momentarily to enter the “Memory Check” mode, which is
3. Press the
used to find an unused memory channel. The frequency stored (if any) on the current
memory channel will be shown in the display.
4. Rotate the
knob to select the channel number on which you wish to store the
current frequency data.
(MW) key for one second until you hear a double beep; the
5. Press and hold in the
second beep confirms that the frequency information was successfully stored.
Split-Frequency Memory Storage
You can also store “Split” frequencies, such as when operating on a repeater system not utilizing a “standard” offset. This procedure may also be used for DX work on 7 MHz SSB, etc.
1. In the VFO mode, set the desired Receive frequency and mode.
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 2 [MW, MC, TAG] appears on the display.
(MW) key momentarily to enter the “Memory Check” mode, which is
3. Press the
used to find an unused memory channel. The frequency stored (if any) on the current
memory channel will be shown in the display.
4. Rotate the
knob to select the channel on which you wish to store the receive
frequency data.
(MW) key for one second until you hear a double beep, which
5. Press and hold in the
confirms that the Receive frequency data is now stored.
6. Now, set the desired Transmit frequency and mode on the VFO.
(MW) key momentarily; do not rotate the
7. Press the
knob!
8. While the “memory channel number” is blinking, press and hold in the PTT switch;
(MW) key for one second. The double
while holding it in, press and hold in the
“beep” will confirm that independent Transmit frequency data is now stored. You may
now release the PTT switch.
In step 8 above, pressing the PTT switch does not activate the transmitter. It simply sends a signal to the microprocessor that an independent Transmit frequency
is being stored on the same channel as a previously-stored Receive frequency.
FT-817ND Operating Manual
45
MEMORY OPERATION
MEMORY OPERATION ON “REGULAR” MEMORY CHANNELS
Memory Channel Recall
1. If you currently are in the VFO tuning mode, press the
key once to enter the
“Memory” mode (a memory channel number “M-nnn” will appear on the display in she
space previously occupied by “VFOa” or “VFOb”).
2. To select another memory channel, turn the
knob.
3. When your memory channels are partitioned into Memory
Groups via Menu #34, it is easy to change Memory Groups;
[Memory Group “OFF”]
press the
knob momentarily (a Group Number (“a” ~ “j”)
will blink), then turn the
knob to step through the channels until you enter another. You may now press the
knob
once more to restrict memory channel access to the newly-se[Memory Group “ON”]
lected Group.
4. Once you are operating on a memory channel, you may tune off of the originally-memorized frequency (as though you were in the VFO mode). Just rotate the
knob; the
“Memory Channel Number” will be replaced by one which indicates “MTUNE,” indicating that you have now shifted into the “Memory Tuning” mode. When operating the
Memory Tuning mode, if you find another frequency you wish to store into another
(MW) key momentarily, select a new memory chanmemory channel, just press the
(MW) key until you hear the
knob, then press and hold in the
nel via the
double beep.
key as follows:
5. To exit the Memory Tuning mode, press the
One
touch
of
the
key
returns
you
to
the
original
memory frequency.
key will cause you to exit the Memory mode and return to
A second touch of the
the VFO mode (the memory channel number will be replaced by “VFOa” or “VFOb”).
When operating on a “Split” frequency memory, a special “
appear on the LCD.
46
” indication will
FT-817ND Operating Manual
MEMORY OPERATION
MEMORY OPERATION ON “REGULAR” MEMORY CHANNELS
Masking Memory
Frequency data stored on a memory channel can be deleted, if desired, from any memory
channel except channel “1.” The deletion process is not a “hard” erasure, so if you erase a
channel by mistake using this procedure, the memory channel contents can be recovered.
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 2 [MW, MC, TAG] appears on the display.
(MW) key momentarily, then rotate the
2. Press the
knob to select the memory
channel to be deleted.
(MC) key momentarily. The frequency display field on the LCD will go
3. Press the
blank, and the memory channel number will blink.
4. Wait about three seconds; when the memory channel number stops blinking, the data
will now be “masked” and will not be available for operation.
5. To restore the masked frequency data, repeat the above steps. However, if you store new
frequency information on a channel containing masked data, the masked data will be
over-written and lost.
6. Memory Channel 1 is used for Priority operation, and frequency information may only
be over-written (not masked) on this channel.
FT-817ND Operating Manual
47
MEMORY OPERATION
MEMORY OPERATION ON “HOME” CHANNEL MEMORIES
Four Special one-touch “Home” channels are available, for special frequencies you use
often. Either “simplex” or “split” frequency/mode data may be stored in the “Home” channel locations. Special “Home” channels are available for HF (any frequency between 1.8
and 29.7 MHz), 50 MHz, 144 MHz, and 430 MHz.
These memories may prove particularly useful for monitoring propagation beacons, providing one-touch recall of the beacon frequency for a quick check of band conditions.
HOME Channel Storage
1. Tune the desired frequency, and set the operating mode. If this is an FM channel, set up
any required CTCSS/DCS and repeater shift configurations.
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 2 [MW, MC, TAG] appears on the display.
(MW) key momentarily to enter the “Memory Check” mode.
3. Press the
4. Press and hold in the
key for one second. This stores the frequency data into the
“Home” channel location. As usual, you will hear a double beep to confirm the successful storage of the frequency data.
5. If you wish to store a “Split” frequency pair into the “Home” channel, store the Receive
frequency in steps 1 ~ 4 above. Now set the desired Transmit frequency.
(MW) key momentarily.
6. Once more, press the
7. Press and hold in the microphone’s PTT switch; while holding the PTT switch, again
key for one second. This stores the transmit frequency data into
press and hold the
the “Home” channel location.
HOME Channel Recall
1. Press the
key momentarily to recall the Home Channel on the band group where
you currently are operating (HF, 50 MHz, 144 MHz, or 430 MHz). The “HOME” indication will appear on the display.
2. Press the
key once more to return to the previously-used frequency (either a VFO
frequency or a memory channel).
48
FT-817ND Operating Manual
MEMORY OPERATION
LABELING MEMORIES
You may wish to append an alpha-numeric “Tag” (label) to a memory or memories, to aid in
recollection of the channel’s intended use (such as a club name, etc.). This is easily accomplished using the Menu mode.
1.
2.
3.
4.
5.
Recall the memory channel onto which you wish to appended a label.
key for one second to enter the Menu mode.
Press and hold in the
Rotate the
knob to recall Menu #35 (MEM TAG).
Press the
knob to enable the programming of the label.
Rotate the
knob to select the first character (number, letter, or symbol) in the name
you with to store, then rotate the
knob clockwise to move to the next character.
6. Again rotate the
knob to select the next number, letter, or symbol, then rotate the
knob clockwise to move to the next character’s slot.
7. Repeat step 6 as many times as necessary to complete the name tag for the memory, then
press and hold in the
key for one second to save the A/N (Alpha-Numeric) name
entry and exit to normal operation.
During Memory operation, press the
key momentarily, then rotate the
knob, as needed, until Operating Function Row 2
[MW, MC, TAG] appears on the display. Press the
(TAG) key
momentarily to activate the alpha-numeric Tag. Repeatedly pressing this key will toggle operation between “Frequency” display and
“Tag” display.
You can recall Menu #35 (MEM TAG) instantly by press(TAG) key for one second.
ing and holding in the
FT-817ND Operating Manual
[“Frequency” Display]
[“Tag” Display]
49
SPECTRUM SCOPE MONITOR OPERATION
The Spectrum Scope Monitor allows viewing of operating activity on 5 channels above and
5 channels below the current operating channel in the VFO mode.
When the Spectrum Scope Monitor is activated, the display indicates the relative signal strength on channels immediately adjacent
to the current operating frequency.
Two basic operating modes for Spectrum Scope are available:
CONT: In this mode, the transceiver sweeps the current band repeatedly until the Spectrum
Scope is turned off.
CHK: In this mode, the transceiver sweeps the current band one cycle every 10 seconds.
Setting the Spectrum Scope Mode
1.
2.
3.
4.
Press and hold in the
key for one second to enter the Menu mode
Rotate the
knob to select Menu #43 (SCOPE).
Rotate the
knob to select the desired sweep mode (see above).
When you have made your selection, press and hold in the
key for one second to save
the new setting and exit to normal operation.
Activate the Spectrum Scope
1. Set the transceiver to the VFO mode in the desired band.
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 6 [SSM, SCH, ART] appears on the display.
(SSM) key momentarily to engage the Spectrum Scope.
3. Press the
4. When the Spectrum Scope is in operation, the relative signal strength of stations on
channels immediately adjacent to the current frequency will be indicated on the display.
(SSM) key once more.
5. To disable the Spectrum Scope, press the
The receiver’s audio output and S-meter are disabled when using the Spectrum
Scope.
50
FT-817ND Operating Manual
SMART SEARCH™ OPERATION
TM
The Smart Search feature automatically stores frequencies where activity is encountered
on the current band. When Smart SearchTM is engaged, the transceiver quickly searches
above your current frequency, storing active frequencies as it goes (without stopping on
them even momentarily). These frequencies are stored in a special Smart SearchTM memory
bank, consisting of 50 memories. This feature available on the FM and AM modes.
The Smart Search™ feature is especially helpful when traveling, as you can instantly store
active FM repeater frequencies without having to look up the frequencies in a reference
book.
1. Set the
knob to the point where background noise is silenced. A typical setting,
for effective Smart SearchTM operation, will be at 12 o’clock or slightly clockwise from
this position.
2. Set the VFO to the frequency on which you wish to begin the search (the Smart SearchTM
feature is available on the VFO mode only).
3. Press the
key momentarily, then rotate the
knob, as needed, until Operating
[
]
Function Row 6 SSM, SCH, ART appears on the display.
(SCH) key momentarily; the blinking “SRCH” indicator will appear
4. Now press the
on the LCD, and the transceiver will sweep upward on the current band, loading channels on which it encounters a signal strong enough to open the squelch.
5. All channels where activity is present (up to 50 channels) will be loaded into the Smart
SearchTM memories. Whether or not all 50 memories are filled, the search will stop after
one sweep.
6. Now you can turn the
knob to select from the just-stored Smart SearchTM memories. If you find frequencies you wish to store into a “regular” memory, just follow the
(SCH) key while storing these
procedures described previously; just don’t press the
memories, because this will disable Smart Search™ operation (see step 7).
(SCH) key momentarily.
7. To disable Smart SearchTM operation, press the
The Smart Search™ memories are so-called “soft” memories; they will be lost if
you initiate a new Smart SearchTM sweep of the band.
FT-817ND Operating Manual
51
SCANNING OPERATION
This transceiver contains a wide variety of scanning capabilities. Whether you are in the
VFO mode or one of the memory modes, scanning operation is fundamentally identical in
all configurations, but with the following differences:
In the VFO mode, scanning causes the transceiver to sweep up or down the band,
pausing or halting on any signal encountered;
In the Memory mode, the scanner will scan the programmed memories, and can be
instructed to skip certain memories during scanning;
In the Programmable Memory Scan (PMS) mode, the scanner will scan the band
within user-programmed frequency limits.
Scanning Operation
1. Set the
knob to the point where background noise is silenced. A typical setting,
for effective scanning operation, will be at 12 o’clock or slightly clockwise from this
position.
2. Set the transceiver into the operating configuration in which you wish to scan (VFO or
Memory; PMS will be described later).
8. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row [SCN, PRI, DW].
(SCN) key momentarily to start upward scan (toward higher frequencies
3. Press the
or higher memory channel numbers).
4. Rotate the
knob or
knob counterclockwise to toggle the scanning direction
downward.
5. The scanner will now cause the transceiver to increment in the chosen direction until a
signal is detected. When a signal is encountered which opens the Squelch, In the FM/
AM modes, the scanner will pause until the signal disappears (at the end of the other
station’s transmission), at which point scanning will resume. While the transceiver is in
the “Pause” condition, the decimal points in the frequency display area will blink. See
“Scan-Resume Choices” on the next page for details of how to customize the resumption
of scanning, In the SSB/CW modes, the scanner will slow down (but doesn’t stop).
6. Press the PTT switch on the microphone to cancel scanning.
You may also press and hold in either the [UP] or [DWN] key on the microphone
for 1/2 second to initiate upward or downward scanning, respectively, if Menu #37
(MIC SCAN) is set to “ON.”
52
FT-817ND Operating Manual
SCANNING OPERATION
Scan Skip Programming (Memory Mode Only)
Among the memories you have programmed, there may be some stations which you do not
wish to scan. For example, broadcast signals (which are transmitted continuously) will cause
the scanner to stop, and such channels may be skipped so as to avoid this inconvenience.
To remove a channel from the scanning loop:
1. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 2 [MW, MC, TAG] appears on the display.
2. Recall the memory channel to be skipped.
(MC) key momentarily. The “hyphen” in the
3. Press the
memory channel number will change to become a “dot”; this
[Memory Skip “OFF”]
shows that this channel now is not included in the scanning loop.
4. Repeat steps 2 and 3 as many times as necessary to skip all the
channels you do not wish to scan.
5. Initiate memory scanning; you will observe that the channels
[Memory Skip “ON”]
you marked to be skipped are not included in the scanning loop.
6. Press the PTT switch to stop the scan; you may now use the
knob to step through
the channels manually - one at a time - and you will observe that the “Skipped” channels
are, nonetheless, available for recall by manual means.
7. You may restore a previously-skipped channel to the scanning loop by selecting the
(MC) key momentarily so that the “dot” changes
channel manually, then pressing the
to become a “hyphen.”
Downloaded by
RadioAmateur.EU
Scan-Resume Choices
Scanning operation requires that you have the transceiver’s audio squelched. The
transceiver then “assumes” that the opening of the squelch corresponds to the discovery of a signal you may wish to listen to.
Once the scan has been halted, the transceiver pauses on the signal and stays locked
on its frequency for five seconds (default pause time). Thereafter, scanning will resume whether or not the other station’s transmission has ended. The scan resume
interval can be set to 3/5/10 seconds, or off ( whereby scanning quits when a signal is
received) via Menu #41 (RESUME); see page 66 for details.
FT-817ND Operating Manual
53
SCANNING OPERATION
Programmable Memory Scan (PMS) Operation
To limit scanning (or tuning) within a particular frequency range, you can use the Programmable Memory Scanning (PMS) feature, which utilizes special-purpose memory pair (“MPL” and “M-PU”). The PMS feature is especially useful in helping you to observe any operating sub-band limits which apply to your Amateur license class.
PMS setup is simple to accomplish;
1. Store the upper and lower frequency limits of the desired range into the PMS memory
pair (“M-PL” and “M-PU”).
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 3 [STO, RCL, PMS] appears on the display.
(PMS) key. The “PMS” indication will appear at the upper left corner of
3. Press the
the LCD, signifying that the PMS feature is engaged. Tuning and scanning are now
limited within the range between the selected PMS memory pair, keeping operation inside this programmed range.
Example: Limit tuning &amp; scanning to the frequency range 144.300 - 148.000 MHz
1. Press the
key, as necessary, to recall the VFO mode. Tune the
knob or
knob to 144.300 MHz.
2. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 2 [MW, MC, TAG] appears on the display.
(MW) key momentarily, then turn the
3. Press the
knob to select memory channel “M-PL.”
(MW) key for one second to write the VFO frequency into
4. Press and hold in the
“M-PL.”
5. Now, tune the
knob or
knob to 148.000 MHz).
(MW) key momentarily, then turn the
knob to select memory chan6. Press the
nel “M-PU.”
(MW) key for one second to write the VFO frequency into
7. Press and hold the
“M-PU.”
8. Press the
key momentarily, then rotate the
knob one click clockwise to recall
[
]
Operating Function Row 3 STO, RCL, PMS .
(PMS) key momentarily. Tuning and scanning are now limited to the
9. Press the
144.300 ~ 148.000-MHz range until you press the
key to return to memory or VFO
operation.
54
FT-817ND Operating Manual
SCANNING OPERATION
Note
The frequency resolution for these sub-band limits is 100 kHz, although the channel
resolution of the sub-band limit memories in whatever you have selected as the current step size. As a result, the frequencies stored in these special memories (M-PL and
M-PU) are both rounded down to the nearest 100 kHz for their roles as sub-band
limits. Therefore, in the above example, any frequency between 144.300 and 144.399
MHz may be used to store a lower tuning limit of “144.300 MHz” in memory M-PL.
FT-817ND Operating Manual
55
DUAL WATCH OPERATION
Dual Watch is similar, in some respects, to scanning. In Dual Watch, however, the transceiver monitors (squelched) on the VFO-A frequency while periodically checking VFO-B
for activity (or vice-versa). A typical example might be for you to set VFO-A to 50.110
MHz, watching for DX stations who might call CQ on that frequency, while periodically
checking 28.885 MHz for stations reporting band openings on 6 meters.
To activate Dual Watch:
1. Set up transmit and receive operation on VFO-A, establishing your primary monitoring
frequency. Set up the frequency to be checked periodically on VFO-B.
2. Recall VFO-A, then rotate the
control until the background noise is just silenced.
3. Press the
key momentarily, then rotate the
knob, as needed, until Operating
Function Row 5 [SCN, PRI, DW] appears on the display.
(DW) key momentarily to activate Dual Watch operation (the “DW” icon
4. Press the
will appear at the bottom left corner of the LCD.
5. The transceiver will continue to monitor (squelched) on the current (VFO-A) frequency,
but every five seconds will switch briefly to VFO-B frequency, looking for activity.
6. If a station is detected on the VFO-B frequency, the transceiver will pause on the VFOB frequency (the decimal point in the frequency will blink).
(DW) key again to cancel Dual Watch operation (the “DW” icon will
7. Press the
disappear).
Note that pressing the PTT switch on the microphone does not cancel Dual Watch
operation.
56
FT-817ND Operating Manual
OPERATION ON ALASKA EMERGENCY FREQUENCY: 5167.5 KHZ (U.S. VERSION ONLY)
Section 97.401(d) of the regulations governing amateur radio in the United States permit
emergency amateur communications on the spot frequency of 5167.5 kHz by stations in (or
within 92.6 km of) the state of Alaska. This frequency is only to be used when the immediate
safety of human life and/or property are threatened, and is never to be used for routine
communications.
The FT-817ND includes the capability for transmission and reception on 5167.5 kHz under
such emergency conditions via the Menu system. To activate this feature:
1.
2.
3.
4.
Press and hold in the
key for one second to activate the Menu mode.
Rotate the
knob to select Menu #28 (EMERGENCY).
Rotate the
knob to select “ON.”
Press and hold in the
key to exit the Menu mode.
Emergency communication on this spot frequency is now possible:
Press the
key, as necessary, to enter the Memory mode, then rotate the
knob
to select the emergency channel (M-EMG), which is found between channels M-PU and
M-001.
Note that the receive-mode CLARIFIER functions normally while using this frequency, but
variation of the transmit frequency is not possible. Activation of Menu #28 does not enable
any other out-of-amateur-band capability on the transceiver. The full specifications of the
FT-817ND are not necessarily guaranteed on this frequency, but power output and receiver
sensitivity should be fully satisfactory for the purpose of emergency communication.
If you wish to disable operation on the Alaska Emergency Frequency, repeat the procedure
detailed above, but set Menu #28 to “OFF” in step 3 of the procedure.
In an emergency, note that a half-wave dipole cut for this frequency should be approximately 45’3” on each leg (90’6” total length).
Emergency operation on 5167.5 kHz is shared with the Alaska-Fixed Service. This transceiver is not authorized for operation, under the FCC’s Part 87, for aeronautical communications.
FT-817ND Operating Manual
57
MENU OPERATION
The Menu System allows you to customize a wide variety of transceiver performance aspects and operating characteristics. Once you have gone through the various Menu
customization procedures initially, you will find that you will not have to resort to them
frequently during everyday operation.
Menu Operation
1. Press and hold in the
key for one second. The Menu Item number and a brief title for
the Menu Item will appear in the display.
2. Rotate the
knob to select the Menu Item you wish to work on.
3. When you have chosen the desired Menu Item
number, rotate the
knob to change the
value or condition for the Menu Item.
4. When you have made your selection, press and
hold in the
key for one second to save the
new setting and exit to the normal operation.
key momentarily, it will reset the setting
In step (3) above, if you press the
of that Menu Item to its factory-default value.
key momantarily, you will exit to normal op In step (4) above, if you press the
eration without saving the new setting.
01
Menu Item
144 ARS
02
430 ARS
03
9600 MIC
04
AM&amp;FM DL
05
06
AM MIC
AM STEP
07
ANTENNA
08
APO TIME
09
10
11
12
13
14
15
ARTS BEEP
BACKLIGHT
BATT-CHG
BEEP FREQ
BEEP VOL
CAT RATE
COLOR
16
17
CONTRAST
CW DELAY
18
CW ID
58
Function
Activate/deactivate the Automatic Repeater Shift
when operating on the 144 MHz band
Activate/deactivate the Automatic Repeater Shift
when operating on the 430 MHz band
Adjust the audio input level from the TNC
during 9600 bps Packet operation
Enabling/disabling the
knob
on the AM and FM modes
Adjust the microphone gain level for the AM mode
Select the tuning steps
for the
knob on the AM mode
Select the antenna connector to be used
on each operating band (HF/50/144/430 MHz)
Select the Auto Power Off time
(time before power goes off)
Select the ARTS beep mode
Select the LCD lamp mode
Select the battery charging time
Select the beep frequency
Select the beep volume
Set the transceiver's circuitry for the CAT baud rate
Select the illumination color for the LCD illumination
Setting of the display contrast level
Set the receiver recovery time
during pseudo-VOX CW semi-break-in operation
Enables/disables the CW identifier
during ARTS operation
Available Values
OFF/ON
Default
1
OFF/ON
1
0 ~ 100
50
ENABLE/DISABLE
DISABLE
0 ~ 100
2.5/5/9/10/
12.5/25kHz
FRONT/REAR
50
1
OFF/1h ~ 6h
OFF
OFF/RANGE/ALL
OFF/ON/AUTO
6/8/10 h (hours)
440/880 Hz
0 ~ 100
4800/9600/38400 bps
COLOR1 (Blue)/
COLOR2 (Amber)/
COLOR3 (Violet)
1 ~ 12
10 ~ 500 msec
RANGE
AUTO
8h
880 Hz
50
4800 bps
COLOR1
OFF/ON
OFF
1
5
250 msec
FT-817ND Operating Manual
MENU OPERATION
19
20
Menu Item
CW PADDLE
CW PITCH
Function
Select the keyer paddle's wiring configuration
Setting of the pitch of the CW sidetone, BFO offset,
and CW filter center frequencies
Set the sending speed for the built-in Electronic keyer
21
CW SPEED
22
23
24
CW WEIGHT
DCS CODE
DIG DISP
25
DIG MIC
26
DIG MODE
27
DIG SHIFT
28
EMERGENCY
29
30
FM MIC
FM STEP
31
32
33
34
35
36
ID
LOCK MODE
MAIN STEP
MEM GROUP
MEM TAG
MIC KEY
37
38
MIC SCAN
OP FILTER
39
PKT MIC
40
41
42
43
44
45
46
47
48
49
PKT RATE
RESUME
RPT SHIFT
SCOPE
SIDETONE
SQL/RF-G
SSB MIC
SSB STEP
TONE FREQ
TOT TIME
50
51
52
53
VOX DELAY
VOX GAIN
EXTEND
DCS INV
Define the carrier frequency offset
during DIG (USER-L or USER-U) mode operation
Enable Tx/Rx operation on the Alaska Emergency Channel,
5167.5 kHz (USA Version only)
Adjust the microphone gain level for the FM mode
Select the tuning steps for the
knob
on the FM mode
Store your callsign into the CW identifier
Select the operation of the front panel’s
key
Setting of the
’s tuning speed
Enable/disable the memory grouping feature
Store Alpha-Numeric “Tags” for the memory channels
Enable/disable CW keying
by the microphone’s [UP]/[DWN] keys
Enable/disable scanning access
Enable the optional filter (CW or SSB) path
via the microphone’s [UP]/[DWN] keys
Adjust the audio input level from the TNC
during 1200 bps Packet operation
Set the transceiver’s circuitry for the Packet baud rate
Set the delay time for scanning resumption
Set the magnitude of the Repeater Shift
Select the Spectrum Scope mode
Adjust the CW sidetone volume level
Select the configuration of the front panel’s
knob
Adjust the microphone gain level for the SSB mode
Select the tuning steps for the
knob on the SSB mode
Setting the CTCSS Tone Frequency
Select the Automatic Power Off time
(time before power goes off)
Set the “hang time” for the VOX circuitry
Set the gain of the VOX circuitry's input audio detector
Enable/disable the extended Menu Items (#53 ~ #57)
Select “Normal” or “Inverted” DCS coding
54
55
56
57
R LSB CAR
R USB CAR
T LSB CAR
T USB CAR
Set the Rx Carrier Point for LSB
Set the Rx Carrier Point for USB
Set the Tx Carrier Point for LSB
Set the Tx Carrier Point for USB
Set the Dot:Dash ratio for the built-in electronic keyer
Setting the DCS code
Define the displayed frequency offset
during DIG (USER-L or USER-U) mode operation
Adjust the audio input level from terminal equipment
(such as a TNC or PSK-31 sound card)
during DIG (Digital) mode operation
Select the mode and sideband (if applicable)
in the DIG (Digital) mode
Available Values
NORMAL/REVERSE
300 ~ 1000 Hz
Default
NORMAL
700 Hz
4wpm ~ 60 wpm/
20cpm ~ 300 cpm
1:2.5 ~ 1:4.5
104 Std DCS codes
-3000 ~ +3000 Hz
12 wpm
(60 cpm)
1:3.0
023
0 Hz
0 ~ 100
50
RTTY/
PSK31-L/PSK31-U/
USER-L/USER-U
-3000 ~ +3000 Hz
RTTY
0 Hz
OFF/ON
OFF
0 ~ 100
5/6.25/10/12.5/15/
20/25/50 kHz
–
DIAL/FREQ/PANEL
FINE/COARSE
OFF/ON
–
OFF/ON
50
2
YAESU
DIAL
FINE
OFF
–
OFF
OFF/ON
OFF/SSB/CW
ON
OFF
0 ~ 100
50
1200/9600 bps
OFF/3/5/10 seconds
0 ~ 99.99 MHz
CONT/CHK
0 ~ 100
RF-GAIN/SQL
0 ~ 100
1/2.5/5 kHz
50 Std CTCSS tones
OFF/1 ~ 20 min
1200 bps
5 sec
2
CONT
50
1
50
2.5 kHz
88.5 Hz
OFF
100 ~ 2500 msec
1 ~ 100
OFF/ON
Tn-Rn/Tn-Riv/
Tiv-Rn/Tiv-Riv
-300 ~ +300 Hz
-300 ~ +300 Hz
-300 ~ +300 Hz
-300 ~ +300 Hz
500 msec
50
OFF
Tn-Rn
0 Hz
0 Hz
0 Hz
0 Hz
1: Depends on transceiver version.
2: Depends on operating band and transceiver version.
FT-817ND Operating Manual
59
MENU OPERATION
Menu Item 01 [144 ARS]
Function: Activate/deactivate the Automatic Repeater Shift when operating on the 144 MHz
band.
Available Values: OFF/ON
Default: ON (depending on transceiver version)
Menu Item 02 [430 ARS]
Function: Activate/deactivate the Automatic Repeater Shift when operating on the 430 MHz
band.
Available Values: OFF/ON
Default: ON (depending on transceiver version)
Menu Item 03 [9600 MIC]
Function: Adjust the audio input level from the TNC during 9600 bps Packet operation.
Available Values: 0 ~ 100
Default: 50
Menu Item 04 [AM&amp;FM DL]
Function: Enabling/disabling the
knob on the AM and FM modes.
Available Values: ENABLE/DISABLE
Default: DISABLE
Menu Item 05 [AM MIC]
Function: Adjust the microphone gain level for the AM mode.
Available Values: 0 ~ 100
Default: 50
Menu Item 06 [AM STEP]
Function: Select the tuning steps for the
knob on the AM mode.
Available Values: 2.5/5/9/10/12.5/25kHz
Default: 5 kHz (depending on transceiver version)
Menu Item 07 [ANTENNA]
Function: Select the antenna connector to be used on each operating band (HF/50/144/430
MHz).
Available Values: FRONT/REAR
Default: HF: REAR, 50/144/430 MHz: FRONT
When select the REAR antenna connector, the “R” icon will appear on the display
Menu Item 08 [APO TIME]
Function: Select the Auto Power Off time (time before power goes off).
Available Values: OFF/1h ~ 6h
Default: OFF
60
FT-817ND Operating Manual
MENU OPERATION
Menu Item 09 [ARTS BEEP]
Function: Select the ARTS beep mode.
Available Values: OFF/RANGE/ALL
Default: RANGE
OFF:
No alert beeps sound; you must look at the display to determine current ARTS
status.
RANGE: A high tone beep will sound when the transceiver first detects that you are within
range, and a low beep will sound when the other station goes out of range.
ALL:
A high tone beep will sound every time a polling transmission is received from the
other station, and a low beep will sound once when the other station goes out of
range.
Menu Item 10 [BACKLIGHT]
Function: Select the LCD lamp mode.
Available Values: OFF/ON/AUTO
Default: AUTO
OFF: Disables the LCD lamp.
ON:
Illuminates the LCD lamp continuously.
AUTO: Illuminates the LCD lamp for five seconds when any key is pressed.
Menu Item 11 [BATT-CHG]
Function: Select the battery charging time.
Available Values: 6/8/10 h (hours)
Default: 8 h
Menu Item 12 [BEEP FREQ]
Function: Select the beep frequency
Available Values: 440/880 Hz
Default: 880 Hz
Menu Item 13 [BEEP VOL]
Function: Select the beep volume
Available Values: 0 ~ 100
Default: 50
Menu Item 14 [CAT RATE]
Function: Set the transceiver’s circuitry for the CAT baud rate to be used.
Available Values: 4800/9600/38400 bps
Default: 4800 bps
FT-817ND Operating Manual
61
MENU OPERATION
Menu Item 15 [COLOR]
Function: Select the illumination color for the LCD illumination.
Available Values: COLOR1 (Blue)/COLOR2 (Amber)/COLOR3 (Violet)
Default: COLOR1(Blue)
Menu Item 16 [CONTRAST]
Function: Setting of the display contrast level.
Available Values: 1 ~ 12
Default: 5
Menu Item 17 [CW DELAY]
Function: Set the receiver recovery time during pseudo-VOX CW semi-break-in operation.
Available Values: 10 ~ 500 msec
Default: 250 msec
The recovery time may be adjusted in steps of 10 msec. A longer delay may be preferable if
you pause frequently while sending.
Menu Item 18 [CW ID]
Function: Enables/disables the CW identifier during ARTS operation.
Available Values: OFF/ON
Default: OFF
Menu Item 19 [CW PADDLE]
Function: Select the keyer paddle’s wiring configuration.
Available Values: NORMAL/REVERSE
Default: NORMAL
NORMAL: Keyer paddle polarity is normal. The “tip” plug connection produces dots, and
the “ring” plug connection produces dashes.
REVERSE: Keyer paddle polarity is inverted. The “tip” paddle produces dashes, and the
“ring” paddle produces dots.
Menu Item 20 [CW PITCH]
Function: Setting of the pitch of the CW sidetone, BFO offset, and CW filter center frequencies.
Available Values: 300 ~ 1000 Hz
Default: 700 Hz
The CW pitch may be adjusted in steps of 50 Hz.
62
FT-817ND Operating Manual
MENU OPERATION
Menu Item 21 [CW SPEED]
Function: Set the sending speed for the built-in Electronic keyer.
Available Values: 4wpm ~ 60 wpm/20cpm ~ 300 cpm
Default: 12 wpm (60 cpm)
You can set the sending speed according to either of two units of speed (wpm: words per
minute; cpm: characters per minute). To switch units between “wpm” and “cpm,” just press
the
knob.
Menu Item 22 [CW WEIGHT]
Function: Set the Dot:Dash ratio for the built-in electronic keyer.
Available Values: 1:2.5 ~ 1:4.5
Default: 1:3.0
Menu Item 23 [DCS CODE]
Function: Setting the DCS code.
Available Values: 104 Standard DCS codes
Default: 023
DCS CODE
023 025 026 031 032 036 043 047 051 053
054 065 071 072 073 074 114 115 116 122
125 131 132 134 143 145 152 155 156 162
165 172 174 205 212 223 225 226 243 244
Menu Item 24 [DIG DISP]
Function: Define the displayed frequency offset during DIG (USER-L or USER-U) mode
operation.
Available Values: –3000 ~ +3000 Hz
Default: 0 Hz
245 246 251 252 255 261 263 265 266 271
274 306 311 315 325 331 332 343 346 351
356 364 365 371 411 412 413 423 431 432
445 446 452 454 455 462 464 465 466 503
506 516 523 526 532 546 565 606 612 624
627 631 632 654 662 664 703 712 723 731
732 734 743 754
–
–
–
–
–
–
Menu Item 25 [DIG MIC]
Function: Adjust the audio input level from terminal equipment (such as a TNC or PSK-31
sound card) during DIG (Digital) mode operation.
Available Values: 0 ~ 100
Downloaded by
Default: 50
RadioAmateur.EU
Menu Item 26 [DIG MODE]
Function: Select the mode and sideband (if applicable) in the DIG (Digital) mode.
Available Values: RTTY/PSK31-L/PSK31-U/USER-L/USER-U
Default: RTTY
RTTY: AFSK RTTY operation on the LSB mode
PSK31-L: PSK-31 operation on the LSB mode
PSK31-U:PSK-31 operation on the USB mode
USER-L: User-programmed costume operation based on LSB mode
USER-U: User-programmed costume operation based on USB mode
In the USER-L and USER-U modes, you can define the display frequency offset
and carrier frequency offset by menu Items #24 (DIG DISP) and #27 (DIG SHIFT).
FT-817ND Operating Manual
63
MENU OPERATION
Menu Item 27 [DIG SHIFT]
Function: Define the carrier frequency offset during DIG (USER-L or USER-U) mode
operation.
Available Values: –3000 ~ +3000 Hz
Default: 0 Hz
Menu Item 28 [EMERGENCY]: USA Version only
Function: Enable Tx/Rx operation on the Alaska Emergency Channel, 5167.5 kHz.
Available Values: OFF/ON
Default: OFF
When this Menu Item is set to “ON,” the spot frequency of 5167.5 kHz will be enabled. To
get to this frequency, use the
knob to navigate; the Alaska Emergency Channel will be
found between the Memory channel “M-PU” and “M-001.”
Use of this frequency is restricted to amateurs operating in (or within 92.6 km of)
the U.S. State of Alaska, and it is to be used for emergency communications only
(involving the immediate protection of life or property).
Menu Item 29 [FM MIC]
Function: Adjust the microphone gain level for the FM mode.
Available Values: 0 ~ 100
Default: 50
Menu Item 30 [FM STEP]
Function: Select the tuning steps for the
knob on the FM mode.
Available Values: 5/6.25/10/12.5/15/20/25/50 kHz
Default: 5 kHz (depends on operating band and transceiver version)
Menu Item 31 [ID]
Function: Store your callsign into the CW identifier. Up to eight characters may be stored.
The storage procedure is as follows:
1. Press the
knob momentarily to initiate callsign storage (an “under-bar” will
appear below the first character location of the callsign).
2. Rotate the
knob to select the first letter/number of your callsign, then rotate
the
knob one click clockwise to save the first letter/number and move to the
next entry position.
3. Repeat the previous step as many times as necessary to complete your callsign.
4. Press the
knob to save your completed callsign and exit.
Default: YAESU
64
FT-817ND Operating Manual
MENU OPERATION
Menu Item 32 [LOCK MODE]
Function: Select the operation of the front panel’s
key.
Available Values: DIAL/FREQ/PANEL
Default: DIAL
DIAL: Locks
knob only
FREQ: Locks front panel keys and knobs related to frequency control (such as
(A/B) key., etc.)
and
key,
PANEL: Locks all front keys and knobs (except
key and
key)
Menu Item 33 [MAIN STEP]
Function: Setting of the
knob’s tuning speed.
Available Values: FINE/COARSE
Default: FINE
You may choose between two speeds for the
knob. Selecting “COARSE” doubles the
tuning rate compared to the default value.
Menu Item 34 [MEM GROUP]
Function: Enable/disable the memory grouping feature
Available Values: OFF/ON
Default: OFF
When this Menu Item is set to “ON,” the 200 “standard” memory channels are partitioned
into ten Memory Groups, each holding up to 20 memory channels.
Menu Item 35 [MEM TAG]
Function: Store Alpha-Numeric “Tags” for the memory channels.
Up to eight characters may be stored. The storage procedure is as follows:
1. Recall the memory channel on which you wish to append a label.
2. Recall this Menu Item [Menu #35 (MEM TAG)].
3. Press the
knob momentarily to initiate storing of the Tag (an under-bar will
appear below the first character location).
4. Rotate the
knob to select the first character (number, letter, or symbol) in the
name you with to store, then rotate the
knob clockwise to move to the next
character.
5. Again rotate the
knob to select the next number, letter, or symbol, then rotate
the
knob clockwise to move to the next character’s slot.
6. Repeat step 5 as many times as necessary to complete the name tag for the memory.
7. Press the
knob to save the A/N (Alpha-Numeric) Tag and exit.
FT-817ND Operating Manual
65
MENU OPERATION
Menu Item 36 [MIC KEY]
Function: Enable/disable CW keying by the microphone’s [UP]/[DWN] keys.
Available Values: OFF/ON
Default: OFF
When this Menu Item is set to “ON,” press the microphone’s [UP] key to send a “dot,” and
press the microphone’s [DWN] key to send a “dash” (while the built-in electronic keyer is
engaged).
Menu Item 37 [MIC SCAN]
Function: Enable/disable scanning access via the microphone’s [UP]/[DWN] keys.
Available Values: OFF/ON
Default: ON
Menu Item 38 [OP FILTER]
Function: Enable the optional filter (CW or SSB) path.
Available Values: OFF/SSB/CW
Default: OFF
After installing the optional filter, set this Menu Item to define the signal path corresponding
top the filter you have installed.
Menu Item 39 [PKT MIC]
Function: Adjust the audio input level from the TNC during 1200 bps Packet operation.
Available Values: 0 ~ 100
Default: 50
Menu Item 40 [PKT RATE]
Function: Set the transceiver’s circuitry for the Packet baud rate to be used.
Available Values: 1200/9600 bps
Default: 1200 bps
Menu Item 41 [RESUME]
Function: Set the delay time for scanning resumption.
Available Values: OFF/3/5/10 seconds
Default: 5 sec
When this Menu Item set to “OFF,” the scanner stops (without restarting) until you press the
(SCN) key (or the microphone’s [UP]/[DWN] keys).
Menu Item 42 [RPT SHIFT]
Function: Set the magnitude of the Repeater Shift.
Available Values: 0 ~ 99.99 MHz
Default: Depends on transceiver version, and the band in use.
Each band’s repeater shift (HF/50/144/430 MHz) may be set independently.
66
FT-817ND Operating Manual
MENU OPERATION
Menu Item 43 [SCOPE]
Function: Select the Spectrum Scope mode.
Available Values: CONT/CHK
Default: CONT
CONT: The Spectrum Scope sweeps continuously.
CHK: The Spectrum Scope sweeps one cycle every 10 seconds.
Menu Item 44 [SIDETONE]
Function: Adjust the CW sidetone volume level.
Available Values: 0 ~ 100
Default: 50
Menu Item 45 [SQL/RF-G]
Function: Select the configuration of the front panel’s
Available Values: RF-GAIN/SQL
Default: Depends on transceiver version
knob.
Menu Item 46 [SSB MIC]
Function: Adjust the microphone gain level for the SSB mode.
Available Values: 0 ~ 100
Default: 50
Menu Item 47 [SSB STEP]
Function: Select the tuning steps for the
Available Values: 1/2.5/5 kHz
Default: 2.5 kHz
Menu Item 48 [TONE FREQ]
Function: Setting the CTCSS Tone Frequency.
Available Values: 50 Standard CTCSS tones
Default: 88.5 Hz
Menu Item 49 [TOT TIME]
Function: Select the Automatic Power Off time
(time before power goes off).
Available Values: OFF/1 ~ 20 min
Default: OFF
knob on the SSB mode.
CTCSS TONE FREQUENCY (Hz)
67.0
69.3
71.9
74.4
77.0
82.5
85.4
88.5
91.5
94.8
79.7
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
–
–
–
–
Menu Item 50 [VOX DELAY]
Function: Set the “hang time” for the VOX circuitry.
Available Values: 100 ~ 2500 msec
Default: 500 msec
Downloaded by
RadioAmateur.EU
FT-817ND Operating Manual
67
MENU OPERATION
Menu Item 51 [VOX GAIN]
Function: Set the gain of the VOX circuitry’s input audio detector.
Available Values: 1 ~ 100
Default: 50
Menu Item 52 [EXTEND]
Function: Enable/disable the extended Menu Items (#53 ~ #57).
Available Values: OFF/ON
Default: OFF
Menu Item 53 [DCS INV]
Function: Select “Normal” or “Inverted” DCS coding.
Available Values: Tn-Rn/Tn-Riv/Tiv-Rn/Tiv-Riv
Default: Tn-Rn
“n” = “normal
“iv” = “inverted”
Menu Item 54 [R LSB CAR]
Function: Set the Rx Carrier Point for LSB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
Menu Item 55 [R USB CAR]
Function: Set the Rx Carrier Point for USB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
Menu Item 56 [T LSB CAR]
Function: Set the Tx Carrier Point for LSB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
Menu Item 57 [T USB CAR]
Function: Set the Tx Carrier Point for USB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
68
FT-817ND Operating Manual
CLONING
You can transfer all data stored in one transceiver to another set by utilizing the handy
“Cloning” feature. This requires a user-constructed cloning cable which connects the ACC
jacks on the two transceivers as shown below.
To clone from one transceiver to another, use the following procedure:
1. Insert the Clone Cable into the ACC jack of each transceiver.
2. Turn both transceivers off, then press and hold in the
and
keys on each radio while turning the power on
again. The “CLONE MODE” notation will appear on the display.
3. On the “destination” radio, press the
key.
4. Now, on the “source” radio, press the
key. Data will now
be transferred to the “Destination” radio from the “Source” radio.
5. If there is a problem during the cloning process, “Error” will be
displayed. Check your cable connections and try again.
6. If cloning is successful, turn the “destination” radio off. Now
turn the “source” radio off.
[Distination radio]
[Source radio]
Remove the clone cable. Channel and operating data for both radios are now identical. They
both may be turned on now for normal operation.
Downloaded by
RadioAmateur.EU
FT-817ND Operating Manual
69
CAT SYSTEM PROGRAMMING
The FT-817ND’s CAT System allows the transceiver to be controlled by a personal computer. This allows multiple control operations to be fully automated as a single mouse click,
or it allows a third-party software package (such as contest logging software) to communicate with the FT-817ND without (redundant) operator intervention.
The Optional CAT Interface Cable CT-62 is a connection cable for the FT-817ND and
your computer. The CT-62 has a built-in level converter, allowing direct connection from
the rear panel ACC jack to the serial port of your computer, without the need for an external
RS-232C level converter box.
Vertex Standard does not produce CAT System operating software, due to the wide variety
of personal computers, operating systems, and applications in use today. However, the FT817ND (and other Yaesu products) are widely supported by third-party software packages,
and we recommend that you contact your dealer for advice, or check advertisements in
amateur radio journals. Most software vendors also have Home Pages on the World Wide
Web which contain a wealth of information on the features and radio support for their software packages.
The information presented in this section will allow the programmer to understand the command structure and opcodes used in the FT-817ND’s CAT System.
70
FT-817ND Operating Manual
CAT SYSTEM PROGRAMMING
CAT Data Protocol
All commands sent from the computer to the transceiver consist of five-byte blocks, with up
to 200 ms between each byte. The last byte in each block is the instruction opcode, while the
first four bytes of each block are arguments (either parameters for that instruction, or dummy
values required to pad the block out to five bytes). Each byte consists of 1 start bit, 8 data
bits, no parity bit, and two stop bits.
CAT DATA BYTE FORMAT
CAT 5-BYTE COMMAND STRUCTURE
There are 17 instruction opcodes for the FT-817ND, listed in the chart on next page. Many of
these opcodes are On/Off toggle commands for the same action (e.g. “PTT On” and “PTT
Off.” Most of these commands require some parameter or parameters to be set. Irrespective
of the number of parameters present, every Command Block sent must consist of five bytes.
Accordingly, any CAT control program must construct the five-byte block by selecting the
appropriate instruction opcode, organizing the parameters as needed, and providing unused
“dummy” Eargument bytes to pad the block to its required five-byte length (the dummy
bytes can contain any value). The resulting five bytes are then sent, opcode last, from the
computer to the FT-817ND CPU via the computer’s serial port and the transceiver’s ACC
jack.
All CAT data values are hexadecimal.
Constructing and Sending CAT Commands
Example #1: Set the VFO frequency to 439.70 MHz
Per the CAT command table, the opcode for “Set Frequency” is 01. Placing the opcode
into the 5th data bit position, we then enter the frequency into the first four data bit
positions:
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
43
97
00
00
01
Parameter
Command
Send these five bytes to the transceiver, in the order shown above.
Example #2: Turn the Split Mode “On”
Per the CAT command table, the opcode for “Split On/off” is 02. Placing the opcode
into the 5th data bit position, we then enter dummy values into all other parameter locations:
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
00
00
00
02
00
Dummy Data
Command
FT-817ND Operating Manual
71
CAT SYSTEM PROGRAMMING
OPCODE COMMAND CHART
Command Title
Parameter
Opcode
Notes
LOCK ON/OFF
CMD
PTT ON/OFF
CMD
Set Frequency
P1
P2
P3
P4
01
P1 ~ P4 Frequency Digits
01, 42, 34, 56, [01] = 14.23456 MHz
Operating Mode
P1
07
P1 = 00: LSB,
P1 = 01: USB,
P1 = 02: CW,
P1 = 03: CWR,
P1 = 04: AM,
P1 = 08: FM,
P1 = 0A: DIG,
P1 = 0C: PKT
CMD = 00: LOCK ON
CMD = 80: LOCK OFF
CMD = 08: PTT ON
CMD = 88: PTT OFF
CLAR ON/OFF
CMD
CLAR Frequency
P1
P3
P4
F5
CMD = 05: CLAR ON
CMD = 85: CLAR OFF
P1 = 00: “+” OFFSET
P1 ≠ 00: “–” OFFSET
P3, P4: CLAR Frequency
12, 34 = 12.34 kHz
SPLIT ON/OFF
CMD
Repeater Offset
P1
09
VFO-A/B
81
Toggle
CMD = 02: SPLIT ON
CMD = 82: SPLIT OFF
P1 = 09: “–” SHIFT
P1 = 49: “+” SHIFT
P1 = 89: SIMPLEX
Repeater Offset
P1
P2
P3
P4
F9
P1 ~ P4 Frequency Digits
05, 43, 21, 00, [F9] = 5.4321 MHz
CTCSS/DCS Mode
P1
0A
P1 = 0A: DCS ON
P1 = 2A: CTCSS ON
P1 = 4A: ENCODER ON
P1 = 8A: OFF
CTCSS Tone
P1
P2
DCS Code
P1
P2
Read RX Status
Read TX Status
Read Frequency &amp; Mode Status
POWER ON/OFF
0B
P1 ~ P2: CTCSS Tone Frequency (Note 1)
0C
P1 ~ P2: DCS Code (Note 2)
E7
(Note 3)
F7
(Note 4)
03
(Note 5)
CMD
CMD = 0F: POWER ON (Note 6)
CMD = 8F: POWER OFF
72
FT-817ND Operating Manual
CAT SYSTEM PROGRAMMING
Note 1: CTCSS Tone
Note 2: DCS Code
CTCSS TONE FREQUENCY (Hz)
67.0
69.3
71.9
74.4
77.0
DCS CODE
79.7
023 025 026 031 032 036 043 047 051 053
82.5
85.4
88.5
91.5
94.8
97.4
054 065 071 072 073 074 114 115 116 122
100.0
103.5
107.2
110.9
114.8
118.8
125 131 132 134 143 145 152 155 156 162
123.0
127.3
131.8
136.5
141.3
146.2
165 172 174 205 212 223 225 226 243 244
151.4
156.7
159.8
162.2
165.5
167.9
245 246 251 252 255 261 263 265 266 271
171.3
173.8
177.3
179.9
183.5
186.2
274 306 311 315 325 331 332 343 346 351
189.9
192.8
196.6
199.5
203.5
206.5
356 364 365 371 411 412 413 423 431 432
210.7
218.1
225.7
229.1
233.6
241.8
445 446 452 454 455 462 464 465 466 503
250.3
254.1
–
–
–
–
506 516 523 526 532 546 565 606 612 624
P1, P2: CTCSS Tone Frequency
P1 P2
08 85 = 88.5 Hz
627 631 632 654 662 664 703 712 723 731
732 734 743 754
–
–
–
–
–
–
P1, P2: DCS Code
P1 P2
00 23 = 023
Note 3: Read RX Status
Note 4: Read TX Status
Downloaded by
RadioAmateur.EU
Note 5: Read Frequency &amp; Mode Status
Note 6: POWER ON/OFF
Do not use this command when using Alkaline bat-
teries or the supplied FNB-85 Ni-MH battery Pack.
Send a 5-byte dummy data (such as “00, 00, 00,
00, 00”) first, when send this command.
FT-817ND Operating Manual
73
INSTALLATION OF OPTIONAL ACCESSORIES
OPTIONAL FILTERS YF-122S/YF-122C/YF-122CN
1. Turn the transceiver’s power off by pressing and holding in the
switch for 1/2
second, then remove the FBA-28 Battery Case or FNB-85 Ni-MH Battery Pack from
the transceiver. Additionally, disconnect the DC cable from the INPUT: 13.8V jack
on the rear panel of the transceiver, when operating the FT-817ND with a DC power
supply.
2. Referring to Figure 1, remove the shoulder belt bracket and its two screws from both
side of the transceiver, then remove the five screws affixing the top case of the transceiver, and remove the top case; disconnect the speaker’s connector when you remove
the top case.
3. Refer to Figure 2 for the mounting locations for the optional filters. Position the filter so
that its connectors are aligned with the mounting pins on the board, and push it into
place.
4. Replace the top case (remember to replace the internal speaker’s plug), and connect the
FBA-28 Battery Case or FNB-85 Ni-MH Battery Pack (and/or attach the DC power
supply), and turn the transceiver on by pressing and holding in the
switch.
5. Change the setting of Menu #38 (OP FILTER) to “SSB” (if installing the YF-122S), or
“CW” (for the YF-122C/YF-122CN).
6. Filter installation is now complete.
Speaker's Connector
YF-122S/YF-122C/YF-122CN
Mounting Location
MODE
BAND
DWN
Figure 1
74
HF/VHF/UHF ALL MODE TRANSCEIVER
UP
TRANSMIT/BUSY
Figure 2
FT-817ND Operating Manual
INSTALLATION OF OPTIONAL ACCESSORIES
OPTIONAL HIGH-STABILITY REFERENCE OSCILLATOR TCXO-9
The TCXO-9 provides high stability over a wide range of ambient temperatures, so as to
enhance digital-mode operating.
switch for 1/2
1. Turn the transceiver’s power off by pressing and holding in the
second, then remove the FBA-28 Battery Case or FNB-85 Ni-MH Battery Pack from
the transceiver. Additionally, disconnect the DC cable from the INPUT: 13.8V jack
on the rear panel of the transceiver, when operating the FT-817ND with a DC power
supply.
2. Referring to Figure 1, remove the shoulder belt bracket and its two screws from both
side of the transceiver, then remove the five screws affixing the top case of the transceiver, and remove the top case; disconnect the speaker’s connector when you remove
the top case.
3. Referring to Figure 3, locate the factory-installed REF UNIT on the board. Remove the
factory-installed REF UNIT from the board, then position the TCXO-9 so that its connectors are aligned with the mounting pins on the board, and push it into place.
4. Replace the top case (remember to replace the internal speaker’s plug), and connect the
FBA-28 Battery Case or FNB-85 Ni-MH Battery Pack (and/or attach the DC power
supply).
5. TCXO-9 installation is now complete.
Figure 3
FT-817ND Operating Manual
75
POWER-ON MICROPROCESSOR RESET PROCEDURE
Some or all transceiver settings can be reset to their factory-default states using one of the
following power-on routines:
+ POWER on: Reset all memories and following menu setting to factory-default.
Menu #06 (AM STEP), 23 (DCS CODE), 30 (FM STEP), 35 (MEM TAG), 42 (RPT SHIFT),
47 (SSB STEP), and 48 (TONE FREQ).
+ POWER on: Reset all menu setting (except following menu) to factory-default.
Menu #06 (AM STEP), 23 (DCS CODE), 30 (FM STEP), 35 (MEM TAG), 42 (RPT SHIFT),
47 (SSB STEP), and 48 (TONE FREQ).
76
+ POWER on: CPU master reset for all memories and menu setting.
FT-817ND Operating Manual
APPENDIX
SETUP OF MEMORIES FOR LOW EARTH ORBIT (LEO) FM SATELLITE OPERATION
Although the FT-817ND is not capable of “full duplex” operation (simultaneous transmission and reception), its flexible memory system is ideal for configuring a set of memories for
LEO satellite work.
The example at the right is designed around
the popular satellite UO-14, but the same
principles apply to operation using AO-27,
SO-35, and other such satellites.
First, set up a table of the required operating frequencies. For UO-14, a typical setup
table is shown at the right:
CH #
RX FREQ
TX FREQ
NOTES
1
435.080 MHz 145.9700 MHz
AOS
2
435.075 MHz 145.9725 MHz
3
435.070 MHz 145.9750 MHz Mid Pass
4
435.065 MHz 145.9775 MHz
5
435.060 MHz 145.9800 MHz
LOS
AOS = Acquisition of Signal (Beginning of Pass)
LOS = Loss of Signal (End of Pass)
The above frequencies are nominal, and the changing frequencies reflects the Doppler Shift
which occurs on such satellites, which display rapid apparent motion relative to an earthbased observer. But if we can accommodate a set of several frequency pairs in our memory
system, frequencies that reflect the frequency relationships encountered during a typical
pass, we will have a good chance of having our frequencies properly aligned when it is time
for making a QSO.
So we need to store the above frequency matrix into memories. Note that the receiving
frequency and transmitting frequency are on different bands. Therefore, we will use the
“Split Frequency Memory” storage technique described on page 43.
key momentarily, then rotate the
knob to select Operating Function
First, press the
(A/B) key, if necessary, to select VFOa.
Row 1 [A/B, A=B, SPL]. Press the
Now press the
or
key to select the 70 cm band. Check the setting
of Menu #04 (AM&amp;FM DL). and set this to “ENABLE” to allow smaller frequency increments to be accommodated.
(A/B) key in
Set the VFOa operating frequency to 435.080.00 MHz. Now press the
Operating Function Row 1 to select VFOb, and set VFOb to 145.970.00 MHz. Again press
(A/B) key to return to VFOa. Be sure that both VFOs are set to the FM mode, as
the
well.
Press the
key momentarily, and rotate the
Operating Function Row 2 [MW, MC, TAG].
knob one click clockwise to select
(MW) key momentarily, then rotate the
Press the
knob while the memory chan(MW)
nel number is blinking; select memory channel M-001, then press and hold in the
key until you hear the double beep. We have just stored the first downlink (earth station
receiving) frequency into memory.
FT-817ND Operating Manual
77
APPENDIX
SETUP OF MEMORIES FOR LOW EARTH ORBIT (LEO) FM SATELLITE OPERATION
Press the
key momentarily, then rotate the
knob one click counter-clockwise to re(A/B) key to select VFOb
select Operating Function Row 1 [A/B, A=B, SPL]. Press the
(145.970 MHz).
Again press the
key momentarily, and rotate the
knob one click clockwise to re(MW) key momentarily;
select Operating Function Row 2 [MW, MC, TAG]. Press the
the “M-001” indicator will flash; press and hold in the microphone’s PTT key, and while
(MW) key until you hear the double beep. You have now stored
holding it in press the
the uplink (earth station transmitting) frequency into the same memory register as we did
previously for the downlink frequency.
It’s now time to store the other frequencies in the matrix. Return to Operating Function Row
(A/B) key to return to VFOa on 435.080.00 MHz.
1 [A/B, A=B, SPL], and press the
(A/B)
Now rotate the
knob to set the frequency to 435.075.00 MHz. Press the
key again to select VFOb (145.970 MHz), and rotate the
knob to set the frequency to
(A/B) key to return to VFOa on 435.075.00 MHz.
145.972.50 MHz. Press the
Return to Operating Function 2 [MW, MC, TAG], and repeat the Split Memory storage
process, selecting memory channel M-002 this time when initially storing the 435.075 MHz
receiving frequency.
Now repeat this entire process three more times, filling memory channels M-003, M-004,
and M-005 with the frequencies shown in the chart above.
When it’s time to operate, press the
key, if necessary, to recall the Memory mode, and
rotate the
knob to select channel M-001. This will be the first frequency pair to be
utilized during the UO-14 window of workability when it rises above your local horizon.
The Doppler effect will cause the nominal 435.070 MHz downlink frequency to appear
higher to you, so utilize memory channel M-001 when the satellite first rises. A few minutes
later, switch to M-002, and at mid-pass switch to M-003. As the satellite recedes, switch to
M-004 and then M-005 toward the end of the pass.
The
knob recall of these five channels makes Doppler tracking simple; just choose the
memory channel producing the best signal! You have already programmed an uplink frequency corresponding to the optimum downlink frequency, so you will not need to try to
make difficult VFO adjustments during the brief satellite passes.
The FM passbands used on LEO satellites are sufficiently broad that more precise frequency
adjustment is not needed.
To aid in channel identification, remember that you can use Menu #35 (MEM TAG) to label
each satellite memory (for example, “UO-14a” ~ “UO-14e” for the above five channels).
78
FT-817ND Operating Manual
APPENDIX
SETUP OF MEMORIES FOR LOW EARTH ORBIT (LEO) FM SATELLITE OPERATION
A complete set of frequencies may be stored for each LEO satellite you wish to utilize, and
once configured, the FT-817ND provides a flexible and easy-to-use earth station capability
for these popular satellites.
FT-817ND Operating Manual
79
APPENDIX
BAND DATA FORMAT
The FT-817ND BAND DATA Format (available on the ACC jack) is presented below. The
BAND DATA line provides a stepped voltage, which denotes the current operating band.
This data may be interpreted by an external device (such as an antenna switch or amplifier)to
provide automatic band switching.
BAND
1.8 MHz
3.5 MHz
7 MHz
LEVEL
0.33 V
0.67 V
1.00 V
BAND
10 MHz
14 MHz
18 MHz
LEVEL
1.33 V
1.67 V
2.00 V
BAND
21 MHz
24.5 MHz
28 MHz
LEVEL
2.33 V
2.67 V
3.00 V
BAND
50 MHz
144 MHz
430 MHz
LEVEL
3.33 V
3.67 V
4.00 V
Use shielded cable for interconnections to external devices, so as to prevent RF interference.
Downloaded by
RadioAmateur.EU
80
FT-817ND Operating Manual
1. Changes or modifications to this device not expressly approved by VERTEX
STANDARD could void the user’s authorization to operate this device.
2. This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions; (1) This device may not cause harmful
interference, and (2) this device must accept any interference including
received, interference that may cause undesired operation.
3. The scanning receiver in this equipment is incapable of tuning, or readily
being altered, by the User to operate within the frequency bands allocated
to the Domestic public Cellular Telecommunications Service in Part 22.
This device complies with RSS-210 of Industry Canada. Operation is subject
to the following two conditions; (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesirable operation of the device.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR
RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES
AND FEDERAL LAW.
Copyright 2004
VERTEX STANDARD CO., LTD.
All rights reserved.
No portion of this manual
may be reproduced
without the permission of
VERTEX STANDARD CO., LTD.
Printed in Japan
0405G-QT
Downloaded by
RadioAmateur.EU
E
1
3
7
7
1
0
0
6
">

Hello! I am an AI chatbot specifically trained to assist you with the YAESU . I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Five Watts of output power
Multiband, Multimode
Compact, portable design
Internal battery operation
Advanced features
Menu system

Frequently asked questions

The FT-817ND provides five watts of power output from a 13.8-Volt external power supply.

The FT-817ND supports SSB, CW, AM, FM, and Digital modes.

The FT-817ND covers the 160-10 meter bands, plus the 6 m, 2 m, and 70 cm bands. It also includes the capability for transmission and reception on the five spot frequencies assigned to the Amateur Service in the United States.