5104A
Repeater / power supply
5104A
– 1- or 2-channel version
– 3- / 5-port 3.75 kVAC galvanic isolation
– Loop supply > 17.1 V
– 20 programmable measurement ranges
– Universal supply by AC or DC
Application
• Power supply and signal isolator for 2-wire transmitters.
• Signal isolator for analog current / voltage signals.
• 1 : 1 or signal conversion of analog current / voltage signals.
Connections
Technical characteristics
• The 20 factory-calibrated measurement ranges in the 5104A
can be selected by the internal DIP-switches without the need
for recalibration. Special measurement ranges can be
delivered.
• PR5104A is based on microprocessor technology for gain and
offset. The analog signal is transmitted at a response time of
less than 25 ms.
• Inputs, outputs, and supply are floating and galvanically
separated.
• The output can be connected either as an active current /
voltage transmitter or as a 2-wire transmitter.
Mounting / installation
• Mounted vertically or horizontally on a DIN rail. By way of the
2-channel version up to 84 channels per meter can be
mounted.
This page is automatically generated on the basis of information provided on www.prelectronics.com and affiliated websites. It is provided to you as a service and for information
purpose only. While we have attempted to maintain the information as accurately as possible, the page may contain errors or omissions for which we disclaim any and all liability
Environmental Conditions
Specifications range.......................................
Calibration temperature.................................
Relative humidity............................................
Protection degree...........................................
Output specifications
-20°C to +60°C
20...28°C
< 95% RH (non-cond.)
IP20
Mechanical specifications
Dimensions (HxWxD).....................................
Weight approx................................................
DIN rail type...................................................
Wire size........................................................
Screw terminal torque....................................
109 x 23.5 x 130 mm
225 g
DIN 46277
1 x 2.5 mm2 stranded wire
0.5 Nm
Common specifications
Supply
Supply voltage, universal............................... 21.6...253 VAC, 50...60 Hz or
19.2...300 VDC
Isolation voltage
Isolation voltage, test /
working........................................................... 3.75 kVAC / 250 VAC
Response time
Response time (0...90%, 100...10%)............. < 25 ms
Auxiliary supplies
2-wire supply (pin 44...42
and 54...52).................................................... 28...17.1 VDC / 0...20 mA
Fuse...............................................................
Max. power consumption...............................
Internal consumption......................................
Signal / noise ratio.........................................
EMC immunity influence................................
Extended EMC immunity: NAMUR
NE 21, A criterion, burst.................................
Current output
Signal range...................................................
Min. signal range............................................
Load (@ current output).................................
Load stability..................................................
Current limit....................................................
0...20 mA
16 mA
≤ 600 Ω
≤0.01% of span / 100 Ω
≤ 28 mA
Voltage output
Signal range................................................... 0...1 VDC / 0...10 VDC
Min. signal range............................................ 0.8 VDC / 8 VDC
Load (@ voltage output)................................ ≥ 500 kΩ
Max. external 2-wire supply........................... 29 VDC
Effect of external 2-wire
supply voltage variation................................. < 0.005% of span / V
*of span.......................................................... = of the presently selected
range
Observed authority requirements
EMC............................................................... 2014/30/EU
LVD................................................................ 2014/35/EU
PELV/SELV.................................................... IEC 364-4-41 and EN 60742
Approvals
UL................................................................... UL 508
EAC................................................................ TR-CU 020/2011
DNV Marine.................................................... Stand. f. Certific. No. 2.4
400 mA SB / 250 VAC
≤ 3 W (2 channels)
≤ 2 W (2 channels)
Min. 60 dB (0...100 kHz)
< ±0.5% of span
< ±1% of span
Input specifications
Common input specifications
Max. offset...................................................... 20% of max. value
Current input
Measurement range....................................... 0...20 mA
Min. measurement range (span).................... 16 mA
Input resistance.............................................. Nom. 10 Ω + PTC 10 Ω
Voltage input
Measurement range....................................... 0...10 VDC
Min. measurement range (span).................... 8 VDC
Input resistance.............................................. > 2 MΩ
5104A-042016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement