Memorex MC2863 User`s guide

Memorex MC2863 User`s guide
MC2863
User’s Guide
CD Clock Radio with
Dual Alarm
Before operating this product,
please read these instructions completely.
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of
uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
DANGER:
Invisible and hazardous laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
LASER SAFETY: This unit employs a laser. Only qualified service personnel should attempt to service this device due to possible eye injury.
CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE PROCEDURE HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
1
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating instructions carefully. Please note that these
are general precautions and may not pertain to
your unit. For example, this unit may not have
the capability to be connected to an outdoor
antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be
read before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by
the product's manufacturer as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this product near water- for example,
near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming
pool.
8.
ACCESSORIES
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury and serious damage
to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer or sold with the product. Any mounting of
the product should follow the manufacturer’s
instructions, and should use a mounting accessory recommended by the manufacturer.
8A. An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back
or bottom are provided for ventilation and to
ensure reliable operation of the product and to
protect it from overheating. These openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat source. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided
or the manufacturer's instructions have been
adhered to.
10. POWER SOURCES
This product should be operated only from the
PORTABLE CART WARNING
(symbol provided by RETAC)
2
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)
11.
12.
13.
14.
15.
16.
17.
18.
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your appliance
dealer or local power company. For products
intended to operate from battery power, or other
sources, refer to the operating instructions.
GROUNDING OR POLARIZATION
This product is equipped with a polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
POWER-CORD PROTECTION
Power-supply cords should be routed so that
they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from
the appliance.
LIGHTNING
To protect your product from a lightning storm, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the product due to lightning
and power-line surges.
POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall
into such power lines or circuits. When installing
an outside antenna system, extreme care should
be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
OVERLOADING
Do not overload wall outlets and extension cords
as this can result in a risk of fire or electric shock.
OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type
of liquid on the product.
SERVICING
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
REPLACEMENT PARTS
19.
20.
21.
a.
b.
c.
d.
e.
f.
22.
23.
24.
3
When replacement parts are required, be sure
the service technician uses replacement parts
specified by the manufacturer or those that have
the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
SAFETY CHECK
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen
into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an adjustment of other controls
may result in damage and will often require
extensive work by a qualified technician to
restore the product to its normal operation.
If the product has been dropped or the cabinet
has been damaged.
When the product exhibits a distinct change in
performance - this indicates a need for service.
HEAT
The product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable
entry as practical.
NONUSE PERIODS
The power cord of the appliance should be
unplugged from the outlet when left unused for a
long period of time.
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your equipment by playing it at a
safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion—and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After
all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the
Electronic Industries Association’s Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. This list of sound levels is included for your protection.
Decibel
Level
30
40
50
60
70
80
Example
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
90
100
120
140
180
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
Rocket launching pad
Information courtesy of the Deafness Research Foundation.
NI
C
IND
EST. 1924
S
N
ELECT
EIA
S
O
O C I A TI
IES
4
TR
LISTENING
For A Lifetime
A
We
Want You
U
S
R
O
LOCATION OF CONTROLS
14 151617 18 19
1 2
3 4 56
7
8
20 21 22 23 24
9 10 1112 13
25 26 27 28 29 30 31 32 33 34 35
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
POWER Indicator
VOLUME Control
ALARM 1 Indicator
PM Indicator
FM ST (Stereo) Indicator
Display
AM/FM Dial Scale and Pointer
Battery Compartment (Bottom of
Unit)
ALARM 2 Indicator
REPEAT Indicator
PROGRAM Indicator
TUNING Control
SLEEP Indicator
Left Speaker
POWER/ALARM RESET Button
Alarm (AL1, AL2, AL1+2) Switch
BUZZER/MUSIC/ALARM OFF
Switch
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
5
CD Compartment Door
AC Cord (Rear of Unit)
FM Wire Antenna (Rear of Unit)
CD Door OPEN/CLOSE Area
FUNCTION (CD/AM/FM) Switch
SKIP/HOUR n Button
Right Speaker
TIME Button
ALARM 1 Button
SLEEP Button
DISPLAY Button
ALARM 2 Button
SNOOZE Button
PLAY/PAUSE (®p) Button
RPT. (Repeat) Button
PROG. (Program) Button
STOP (■) Button
SKIP/MINUTE o Button
INSTALLATION
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
AC Outlet
Unravel the AC cord and connect it to a conveniently located AC outlet having 120V and
60Hz only. The Clock Display will illuminate
AC Plug
and “12:00” will appear in the window.
NOTE: If the AC plug does not fit into a nonpolarized outlet, do not file or cut the wide blade.
If the AC cord is disconnected or if there is a power failure, this electronic clock is
designed to continue operating internally (without showing the time on the Clock
Display) with a 9 volt battery (not included). To install the battery, remove the battery compartment cover by pressing in on the tab, connect the battery to the terminals of the battery snap inside the compartment (use of an alkaline battery is recommended), then replace battery compartment cover.
9V
Be sure to check the condition of the battery periodically by disconnecting the AC cord and connecting it
again 2 or 3 minutes later. The preset times should
continue operating. If the present time does not
appear, it indicates the battery is dead or not connected properly. The 9 volt battery will keep the internal
times accurately for approximately 30 minutes. If the
power is restored after 30 minutes, the times may need to be reset.
BATTERY PRECAUTIONS
Follow these precautions when using a battery in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. Reversed battery may cause damage to the device.
3. If the device is not to be used for a long period of time, remove the battery to prevent
damage or injury from possible battery leakage.
4. Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s directions.)
6
OPERATION
TO LISTEN TO THE RADIO
1
2
2
1
2
Press the POWER/ALARM RESET
button 1 to turn the unit on; the
POWER indicator will light. Slide the
FUNCTION switch 2 to the AM or FM
position.
1
Tune a station by turning the TUNING
control 1. When a strong FM stereo
signal is received the FM Stereo indicator will light.
Adjust the VOLUME control 2 as
desired.
Antennas
FM: Extend the FM wire antenna for best reception.
AM: Turn the unit for better AM reception.
FAQ: Why am I not getting sound from the radio?
Make sure the FUNCTION switch is set to the AM or FM position and the
VOLUME control is not set to the minimum level.
TO INSERT A CD
TO REMOVE A CD
1
1
Open the CD compartment door by
pressing on the OPEN/CLOSE area on
the bottom right of the CD compartment
door. Gently place a disc, label side up,
onto the spindle and gently close the
CD compartment door.
Make sure the CD has stopped and
open the CD compartment door by
pressing on the OPEN/CLOSE area on
the CD compartment door. Hold the
edge of the CD and pick it up.
7
OPERATION (CONTINUED)
TO PLAY A CD
1
2
2
1
Insert a CD as described on the previous
page. Press the POWER/ALARM
RESET button 1 to turn the unit on; the
POWER indicator will light. Slide the
FUNCTION switch 2 to the CD position
(the total number of tracks will appear in
the display).
Press the PLAY/PAUSE (®p) button
to start playback. TO PAUSE PLAYBACK, press the PLAY/PAUSE (®p
button again; the display will briefly
blink. Press again to resume playback.
3
4
2
3
1
2
1
To skip forward or backward through the
tracks on the disc, press the SKIP n 1
or o 2 button. To search forward or
backward through the tracks on the disc,
press and hold the SKIP n 1 or o 2
button.
Adjust the VOLUME control 1 as
desired. Press the DISPLAY button 2
when the time is showing to see the
number of tracks on the CD. When the
disc is through playing, it will stop.
Press the STOP (■) button 3 to stop
the disc before it is finished.
FAQS: Do I need an adapter to play 3” singles?
No, simply insert the 3” single into the groove.
What is the maximum time for a CD in this unit?
The maximum time is 74 minutes.
NOTES:
• If a disc is inserted incorrectly, dirty, damaged or not present at all, the display
will show, “no”.
• TO REMOVE THE CD, SEE PAGE 7, TO REMOVE A CD section.
8
OPERATION (CONTINUED)
TO REPEATEDLY PLAY BACK ONE TRACK
1
2
2
1
1
2
4
3
3
Press the POWER/ALARM RESET
button 1 to turn the unit on; the
POWER indicator will light. Slide the
FUNCTION switch 2 to the CD position. Press the REPEAT button 3
once; the REPEAT indicator will blink.
Press the SKIP n 1 or o 2 button to
select a track and the PLAY/PAUSE
(®p) button 3 to start playback and
the unit will play the same track over
and over until the STOP (■) button 4 is
pressed.
TO REPEATEDLY PLAY BACK ALL TRACKS
1
2
2
1
2
1
3
Press the POWER button 1 to turn
the unit on; the POWER indicator will
light. Slide the FUNCTION switch 2 to
the CD position. Press the REPEAT
button 3 twice; the REPEAT indicator
will light solid.
Press the PLAY/PAUSE (®p) button 1
to start playback and the unit will then
play all the tracks on the CD over and
over until the STOP (■) button 2 is
pressed.
9
OPERATION (CONTINUED)
TO PROGRAM THE MEMORY (UP TO 20 TRACKS)
1
2
2
1
2
1
3
3
Press the POWER/ALARM RESET
button 1 to turn the unit on; the
POWER indicator will light. Slide the
FUNCTION switch 2 to the CD position. Press the PROG. button 3 once;
“P 01” will appear in the display and
the PROGRAM indicator will blink.
Within 7 seconds, select the first track
to be played back using the SKIP n 1
or o 2 button, then press the PROG.
button 3 again. Repeat this step to
program additional tracks up to a maximum of 20 tracks.
3
4
2
1
Adjust the VOLUME control 1 as desired.
When the disc is through playing, it will
stop. Press the STOP (■) button 2 to
stop the disc before it is finished.
Press the PLAY/PAUSE (®p) button
to begin playback. The unit will play all
the tracks in the order you programmed them.
NOTES:
• To skip forward or backward through the programs, press the SKIP n or o button. When the disc is through playing, it will stop.
• Programming is the ability to preselect the order in which a series of tracks will
be played.
FAQS: How do I clear the memory?
Press the PROG. button to enter the Program mode, and then
press the STOP ( ) button or change the position of the FUNCTION switch.
10
OPERATION (CONTINUED)
TO SET OR RESET THE ACTUAL TIME
1
2
2
1
3
While holding the TIME button 1,
press the SKIP/HOUR n button 2 to
set the present hour and the
SKIP/MINUTE o button 3 to set the
present minute.
Press and hold the TIME button; the
time will blink.
TO SET OR RESET THE ALARM TIME
2
1
2
3
1
1
While holding the desired ALARM button 1, press the SKIP/HOUR n button
2 to set the desired alarm hour and the
SKIP/MINUTE o button 3 to set the
desired alarm minute.
Press and hold the desired ALARM
button (AL1 or AL2).
11
OPERATION (CONTINUED)
TO SET THE ALARM TO WAKE TO RADIO
1
2
1
1
2
Slide the Alarm switch 1 to the AL1, AL2
or AL1 + AL2 position and the
BUZZER/MUSIC/ALARM OFF switch 2
to the MUSIC position and make sure the
power is off. When the actual time matches the selected preset alarm time(s), the
unit automatically turns on for 59 minutes
and then shuts off.
To shut off the alarm, see TO SHUT THE
ALARM OFF section on the next page.
2
Set the alarm time as previously
instructed.
Slide the FUNCTION
switch 1 to the AM or FM position,
select a radio station and make sure
the VOLUME 2 is set as desired.
TO SET THE ALARM TO WAKE TO CD
1
2
1
3
1
2
4
Slide the Alarm switch 1 to the AL1, AL2
or AL1 + AL2 position and the
BUZZER/MUSIC/ALARM OFF switch 2 to
the MUSIC position and make sure the
power is off. When the actual time matches the selected preset alarm time(s), the
unit automatically turns on for 59 minutes
and then shuts off.
To shut off the alarm, see TO SHUT THE
ALARM OFF section on the next page.
2
Set the alarm time as previously instructed.
Slide the FUNCTION switch 1 to the CD
position, insert a CD and make sure the
VOLUME 2 is set as desired.
You can set the unit to wake up to a CD program by setting the program as described
on page 10. Then, press the PLAY/PAUSE
(®p) button 3 followed by the STOP (■)
button 4 and the program will be set.
WAKING TO A CD OR CD PROGRAM
When waking to a CD or CD program, the unit will play back the tracks on the CD
or the programmed tracks, then it will stop. If the CD or programmed total time is
more than 59 minutes, it will only play back for 59 minutes and then stop.
12
OPERATION (CONTINUED)
TO SET THE ALARM TO WAKE TO BUZZER
1
2
Set the alarm time as previously
instructed. Slide the Alarm switch to
the AL1, AL2 orAL1 + AL2 position.
Slide the BUZZER/MUSIC/ALARM OFF
switch to the BUZZER position and make
sure the power is off. When the actual
time matches the selected preset alarm
time(s), the unit automatically turns on.
To shut off the alarm, see TO SHUT THE
ALARM OFF section below.
TO SHUT THE ALARM OFF
1
To shut the alarm off, press the
POWER/ALARM RESET button 1
once and the alarm time will be reset
for the next day. Slide the
BUZZER/MUSIC/ALARM OFF switch
2 to the OFF position to turn off the
alarm and not set it for the next day.
2
1
SNOOZE
1
The alarm can be temporarily turned
off manually by pressing the
SNOOZE button; the alarm will turn
back on automatically 6 minutes
later. It can be repeated endlessly.
NOTE: In AL1 + AL2 Alarm mode, if both alarms are set, the Snooze feature will
only operate up to the next alarm. If the next alarm time is reached, the unit
automatically turns on for 59 minutes and then shuts off.
13
OPERATION (CONTINUED)
TO ACTIVATE THE SLEEP FUNCTION
1
2
Tune the desired radio station or insert
a CD as previously instructed and press
the POWER/ALARM RESET button to
turn the unit on; the POWER indicator
will light.
Press the SLEEP button and “--” will
appear on the clock display, then
release the button; the SLEEP indicator
will blink.
3
Press the SLEEP button a second time
to set the unit to turn off after 90 minutes. Press a third time to set to 60
minutes. Press a fourth time to set to
30 minutes.
After five seconds, the Sleep function
will activate and the SLEEP indicator
will light solid.
Pressing the SLEEP button again turns
off the Sleep feature.
14
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the disc carefully. Handle the disc only
by its edges. Never allow your fingers to come
in contact with the shiny, unprinted side of the
disc.
• Do not attach adhesive tape, stickers, etc. to
the disc label.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged (scratched).
• When cleaning the disc, wipe in straight lines from the center of the disc to the
outer edge of the disc. Never wipe in circular motions.
B ENZEN E
C LE A N E R
• This unit is designed to play only discs bearing the identification
logo as shown here. Other discs may not conform to the CD standard and may not play properly.
• Discs should be stored in their cases after each use to avoid damage.
• Do not expose discs to direct sunlight, high humidity, high temperatures, or
dust, etc. Prolonged exposure or extreme temperatures can warp the disc.
• Do not stick or write anything on either side of the disc. Sharp writing instruments or the ink may damage the surface.
Cleaning the Unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source
when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other
furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
15
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before calling for service.
SYMPTOM
Unit will not
turn on.
Disc will not play.
CAUSE
AC cord not
connected.
CD compartment
not closed.
Disc inserted
incorrectly.
Dirty or defective CD.
Moisture
condensation on disc.
No sound.
VOLUME control
set to minimum.
Defective disc.
Erratic playback.
Dirty or defective
disc.
Time reset to “12:00”. Battery connected
improperly, not connected or dead.
Clock not set.
Alarm does not
ALARM switch is not
turn on.
in correct position.
Clock is not set.
Alarm is not set.
AM or FM, no sound. Power is not on.
VOLUME control
set to minimum.
16
SOLUTION
Check AC cord
connection.
Close CD compartment
door.
Reinsert disc correctly.
Try another disc.
Wipe disc with soft cloth.
Increase volume.
Try another disc.
Clean or replace disc.
Check the battery.
Set the clock.
Set ALARM switch to the
desired alarm.
Set the clock.
Set the Alarm.
Press the POWER/ALARM
RESET button to turn the unit on.
Increase volume.
SPECIFICATIONS
AUDIO
Frequency Range (AM) ..................................................530–1710KHz
Frequency Range (FM)......................................................88–108MHz
CD SECTION:
Disc Diameter ................................................................4.72” (120mm)
3.15” (80mm) Single CD
Optical Source.....................................................Semiconductor Laser
Wavelength ................................................................................780nm
GENERAL
Power Supply ....................................AC 120V, 60Hz (9V for back-up)
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE
VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90
DAYS IN CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR
PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT
1-800-321-6993.
17
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Visit our website at www.memorexelectronics.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement