Slip-On (2011)

Slip-On (2011)
Installation Instructions
1.
Make sure the ATV is completely cool before starting
the installation. Make sure the ATV is secure on a level
surface and the parking brake is set.
2.
Remove the four bolts that attach the OEM muffler cover.
Remove muffler cover.
3.
Remove four springs that attach OEM muffler to header.
7.
Attach the three grommets to the TBR muffler.
8.
Install TBR muffler as shown.
9.
Attach supplied muffler hanger bracket using the 8x20mm
bolts and nuts that were provided for upper mounts. Use
the OEM bolt and nut with washer on lower mount. Tighten
hardware.
V.A.L.E.
TM
2011 Can-am
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
Commander
V.A.L.E.™ Slip-on Exhaust System with M-7 Aluminum Canister
Part # 005-2960406V
4.
Remove muffler mounting bolts, this may require tilting
the bed to access the nuts on the back side frame rail.
5.
Remove OEM muffler assembly.
6.
Remove one rubber grommet and sleeve, and both
lower grommets.
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Be sure
to save all stock components for possible use later.
**This product has not been tested with all available accessories and some
items may cause excessive heat. Excessive heat may cause damage to your
vehicle. Two Brothers Racing will not be responsible for damaged parts.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
10. Loosely attach the two part X-ring using supplied bolts and
washers and lock tight.
Installation Instructions
11. Loosely attach to muffler and install slip-on pipe.
13. Attach OEM springs joining the OEM header to TBR muffler
assembly.
V.A.L.E.
TM
2011 Can-am
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
Commander
V.A.L.E.™ Slip-on Exhaust System with M-7 Aluminum Canister
Part # 005-2960406V
14. Double check your work and make sure all bolts are
tightened and the exhaust is aligned correctly.
12. Make adjustments and securely tighten X-Ring bolts.
15. Before you run the ATV, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the ATV and enjoy. It is normal for some white smoke to
appear the first time you start the ATV. This is packing/
manufacturing oil from inside the pipe burning off.
Check for gaps or leaks. If you find a leak, a little high
temperature silicon sealant should fix it. After 50 to 100
miles, recheck all fasteners for tightness.
Parts List
Care & Cleaning
Qty.
Description
Part Number
1
1
1
1
1
2
2
1
Muffler Canister M-7 Aluminum
Stainless Steel S-Bend Slip-On HARDWARE KIT
X-Ring Kit Muffler bracket
8mm Flange locking nut
8x20mm Socket Head Flange Bolt
TBR Sticker Kit
005-296-206M
005-29604S
005-296-3
005-7-2-3KIT
005-296-B
005-FLN8
005-FB820
015-10212
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel. Clean using a
mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep blue/purple through amber after a few heat cycles. This is a normal characteristic of high
quality titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack of cooling air can quickly burn through the canister material. Two Brothers Racing
does not provide a warranty for burned canisters.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement