Subzero Design Guide

Subzero Design Guide
Sub-Zero Design Guide
REVISED 8 / 2015
Contents
3
Built-In Refrigeration
38
PRO 48 Refrigeration
44
Integrated Refrigeration
54
Wine Storage
84
Undercounter Refrigeration
94
Sub-Zero Warranties
Features and specifications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
IMPORTANT NOTE: Throughout this guide, dimensions may
vary by ± 1/8" (3). Dimensions in parentheses are millimeters
unless otherwise specified.
BUILT-IN REFRIGERATION
BUILT-IN
Built-In Refrigeration
•Energy efficient; many models are ENERGY STAR®
qualified.
For the built-in line, Sub-Zero designers and engineers took
a fresh look at everything, inside and out. Exterior refinements include redesigned grilles and lower-profile hinges.
Inside, new technology in food preservation makes the builtin line nothing short of revolutionary.
•Advanced water filtration and air purification systems.
•NEW! French door models requires less space for door
clearance to accommodate virtually any-size kitchen.
•Four distinct design approaches: framed, overlay, flush
inset and stainless steel.
•Crisper and deli drawers form a lower-temperature zone
for produce and meats.
•Handle options coordinate with handles of Wolf cooking
products.
PRO 48
•NEW! Internal dispenser models provide chilled water
inside the refrigerator—some models also dispense ice.
KEY FEATURES
•Flip-up grille provides easy access for quick routine
maintenance.
•Dual refrigeration; two compressors preserve food’s
goodness in two sealed compartments.
•All models are Star-K certified.
BUILT-IN MODELS
INTEGRATED
BI-36R
BI-36RG
BI-36F
BI-30U
BI-30UG
BI-36U(ID)
BI-36UG
WINE
BI-36UFD(ID)
BI-42UFD(ID)
BI-36S
BI-42S(ID)
BI-42SD
BI-48S(ID)
BI-48S
UNDERCOUNTER
subzero.com/specs
|
3
BUILT-IN
BUILT-IN REFRIGERATION
PRO 48
Built-In Design Options
FRAMED
OVERLAY
For the classic Sub-Zero look, choose framed custom
door panels that contrast with the stainless steel full-length
handles and louvered grille (shown). The framed application is an overlay model with framed design features. Panel,
grille and handle options are available.
Custom overlay door panels can be combined with unique
handle hardware for design flexibility. Shown with pro
handle option to complement Wolf ranges. Customize with
panel, grille and handle options.
Panels | Custom panels, stainless steel or white enamel.
Grille | Classic louvered grille insert or solid custom panel
for 84" (standard), 83" or 88" overall unit height. Dual wide
grille for dual installations.
Panels | Custom panels or stainless steel.
Grille | Solid custom panel or pro louvered grille for 84"
(standard), 83" or 88" overall unit height. Dual wide grille for
dual installations.
Handles | Custom, tubular or pro handles.
UNDERCOUNTER
WINE
INTEGRATED
Handles | Full-length standard or extended.
Framed.
4
|
Sub-Zero Customer Care 800.222.7820
Overlay.
BUILT-IN REFRIGERATION
BUILT-IN
Built-In Design Options
FLUSH INSET
STAINLESS STEEL
The flush inset design option allows for flush door and grille
panels and custom handle hardware. Shown with tubular
handle option to match Wolf built-in ovens. The flush inset
application is an overlay model with flush inset panels. Customize with panel, grille and handle options.
For a professional look, classic stainless steel models
require no customization. To complement the look of Wolf
ranges, choose the pro handle option (shown). Grille and
handle options are available.
Grille | Solid custom panel or pro louvered grille for 84"
(standard), 83" or 88" overall unit height. Dual wide grille for
dual installations.
Grille | Pro louvered grille for 84" (standard), 83" or 88"
overall unit height. Dual wide grille for dual installations.
PRO 48
Panels | Custom panels or stainless steel.
Handles | Tubular or pro handles.
Handles | Custom, tubular or pro handles.
INTEGRATED
WINE
UNDERCOUNTER
Flush inset.
Stainless steel.
subzero.com/specs
|
5
BUILT-IN
BUILT-IN REFRIGERATION
Overall Dimensions
ALL REFRIGERATOR / ALL FREEZER
26 3/16" (665)
PRO 48
36" (914)
84"
(2134)
73 3/4"
INTEGRATED
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8"
(606)
14 1/8"
(359)
37 1/4"
WINE
(946)
2 3/8" (60)
UNDERCOUNTER
Model BI-36R, BI-36RG and BI-36F.
6
|
Sub-Zero Customer Care 800.222.7820
23 7/8" (606)
Overall dimensions are based on stainless steel models.
For flush inset applications, add 1/2" (13) to door clearance
dimensions.
BUILT-IN REFRIGERATION
BUILT-IN
Overall Dimensions
OVER-AND-UNDER
26 3/16" (665)
30" (762)
26 3/16" (665)
36" (914)
(2134)
50 3/4"
50 3/4"
(1289)
(1289)
23"
23"
(584)
(584)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
(606)
(606)
14 1/8"
12 1/8"
(308)
(600)
23 7/8" (606)
23 7/8"
23 7/8"
23 5/8"
4" (102)
INTEGRATED
HEIGHT DIMENSIONS ± 1/2" (13)
PRO 48
84"
84"
(2134)
(359)
311/4"
(796)
23 5/8"
(600)
37 1/4"
(946)
WINE
2 3/8" (60)
2 3/8" (60)
Model BI-30U and BI-30UG.
Model BI-36U(ID) and BI-36UG.
UNDERCOUNTER
subzero.com/specs
|
7
BUILT-IN
BUILT-IN REFRIGERATION
Overall Dimensions
OVER-AND-UNDER
26 3/16" (665)
PRO 48
36" (914)
26 3/16" (665)
42" (1067)
84"
84"
(2134)
(2134)
50 3/4"
50 3/4"
(1289)
(1289)
23"
23"
INTEGRATED
(584)
HEIGHT DIMENSIONS ± 1/2" (13)
(584)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
23 7/8"
4" (102)
23 7/8"
(606)
(606)
8"
9"
(203)
(229)
23 5/8"
191/2" 23 5/8"
(495)
(600)
(600)
221/4"
WINE
(565)
2 3/8" (60)
UNDERCOUNTER
Model BI-36UFD(ID).
8
|
Sub-Zero Customer Care 800.222.7820
2 3/8" (60)
Model BI-42UFD(ID).
23 7/8" (606)
BUILT-IN REFRIGERATION
BUILT-IN
Overall Dimensions
SIDE-BY-SIDE
26 3/16" (665)
36" (914)
(2134)
73 3/4"
73 3/4"
(1873)
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
4" (102)
23 7/8" (606)
23 7/8"
(606)
(606)
7 1/2"
(191)
8 3/4"
(222)
INTEGRATED
4" (102)
23 7/8"
7 1/4"
(184)
PRO 48
84"
84"
(2134)
HEIGHT DIMENSIONS ± 1/2" (13)
26 3/16" (665)
42" (1067)
10 3/8"
(264)
26 1/4"
221/4"
(668)
(565)
WINE
2 3/8" (60)
2 3/8" (60)
Model BI-36S.
Model BI-42S, BI-42SID and BI-42SD.
UNDERCOUNTER
subzero.com/specs
|
9
BUILT-IN
BUILT-IN REFRIGERATION
Overall Dimensions
SIDE-BY-SIDE
26 3/16" (665)
PRO 48
48" (1219)
84"
(2134)
73 3/4"
INTEGRATED
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8"
(606)
8 3/8"
(213)
11 5/8"
(295)
30"
WINE
(762)
2 3/8" (60)
UNDERCOUNTER
Model BI-48S, BI-48SID and BI-48SD.
10
|
Sub-Zero Customer Care 800.222.7820
23 7/8" (606)
BUILT-IN REFRIGERATION
BUILT-IN
Specifications
BUILT-IN
INTERIOR CAPACITY
ALL REFRIGERATOR / ALL FREEZER
BI-36R
BI-36RG
BI-36F
SHIPPING WEIGHT
R CU FT (L)
F CU FT (L)
23.5 (665)
23.4 (663)
22.7 (643)
ALL REFRIGERATOR / ALL FREEZER
BI-36R
BI-36RG
BI-36F
4.2 (119)
4.2 (119)
5.3 (150)
5.3 (150)
5.3 (150)
6.4 (181)
BI-30U
BI-30UG
BI-36U(ID)
BI-36UG
BI-36UFD(ID)
BI-42UFD(ID)
SIDE-BY-SIDE
R CU FT (L)
F CU FT (L)
SIDE-BY-SIDE
12.4 (351)
16.3 (462)
15.8 (447)
16.0 (453)
19.1 (541)
18.6 (527)
18.8 (532)
8.2 (232)
8.0 (227)
7.9 (224)
7.9 (224)
9.8 (278)
9.6 (272)
9.6 (272)
BI-36S
BI-42S
BI-42SID
BI-42SD
BI-48S
BI-48SID
BI-48SD
OVER-AND-UNDER
BI-36S
BI-42S
BI-42SID
BI-42SD
BI-48S
BI-48SID
BI-48SD
LB (KG)
462 (210)
476 (216)
515 (234)
529 (240)
529 (240)
582 (264)
LB (KG)
538 (244)
582 (264)
608 (276)
608 (276)
630 (286)
656 (298)
656 (298)
Shipping weights are based on stainless steel models.
INTEGRATED
F CU FT (L)
13.2 (374)
13.1 (371)
16.4 (464)
16.3 (462)
15.7 (445)
18.3 (518)
PRO 48
R CU FT (L)
BI-30U
BI-30UG
BI-36U(ID)
BI-36UG
BI-36UFD(ID)
BI-42UFD(ID)
OVER-AND-UNDER
LB (KG)
420 (191)
430 (195)
406 (184)
WINE
UNDERCOUNTER
subzero.com/specs
|
11
BUILT-IN
BUILT-IN REFRIGERATION
Opening Dimensions
STANDARD INSTALLATION
PRO 48
24" (610)
OPENING
DEPTH
INTEGRATED
TOP VIEW
83 3/4"
(2127)
OPENING
HEIGHT
WINE
SIDE VIEW
W
OPENING WIDTH
FRONT VIEW
NOTE: Shaded line represents profile of unit.
OPENING WIDTH
MODEL
UNDERCOUNTER
30" Model
36" Model
42" Model
48" Model
12
|
Sub-Zero Customer Care 800.222.7820
W
29 1/2" (749)
35 1/2" (902)
41 1/2" (1054)
47 1/2" (1206)
If an 83" (2108) grille height is specified, the opening height
must be decreased by 7/8" (22). If an 88" (2235) grille height is
specified, the opening height must be increased by 4" (102).
If two units are installed side by side, refer to page 14 for
dual standard installations.
BUILT-IN REFRIGERATION
BUILT-IN
Opening Dimensions
FLUSH INSET INSTALLATION
26 3/16"
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
PRO 48
FINISHED
CLEATS*
TOP VIEW
11/4"
1/4"
(6)
(32)
INTEGRATED
84"
(2134)
FLUSH
INSET
HEIGHT
W
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
WINE
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
Dimensions assume a 3/4" (19) panel thickness.
FLUSH INSET WIDTH
MODEL
30" Model
36" Model
42" Model
48" Model
W
32" (813)
38" (965)
44" (1118)
50" (1270)
If an 83" (2108) grille height is specified, the flush inset
height must be decreased by 7/8" (22). If an 88" (2235) grille
height is specified, the flush inset height must be increased
by 4" (102).
subzero.com/specs
|
UNDERCOUNTER
If two units are installed side by side, refer to page 15 for
dual flush inset installations.
13
BUILT-IN
BUILT-IN REFRIGERATION
Opening Dimensions
DUAL STANDARD INSTALLATION
PRO 48
24" (610)
OPENING
DEPTH
INTEGRATED
TOP VIEW
(2127)
OPENING
HEIGHT
SIDE VIEW
WINE
W
83 3/4"
OPENING WIDTH
FRONT VIEW
NOTE: Shaded line represents profile of unit.
A dual installation kit will be required for this installation.
DUAL OPENING WIDTH
MODELS
UNDERCOUNTER
Two 30" Models
30" and 36" Models
Two 36" Models
14
|
Sub-Zero Customer Care 800.222.7820
W
59 3/4" (1518)
65 3/4" (1670)
71 3/4" (1822)
BUILT-IN REFRIGERATION
BUILT-IN
Opening Dimensions
DUAL FLUSH INSET INSTALLATION
26 3/16"
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
PRO 48
FINISHED
CLEATS*
TOP VIEW
11/4"
1/4"
(6)
(32)
INTEGRATED
W
84"
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
WINE
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
DUAL FLUSH INSET WIDTH
MODELS
Two 30" Models
30" and 36" Models
Two 36" Models
W
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.
62 1/4" (1581)
68 1/4" (1734)
74 1/4" (1886)
UNDERCOUNTER
subzero.com/specs
|
15
BUILT-IN
BUILT-IN REFRIGERATION
Electrical
Plumbing
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause
interruption of operation.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self‑piercing valves.
The water supply line must not interfere with installation of
the anti-tip brackets.
PRO 48
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
15 amp
Receptacle
3-prong grounding-type
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
1/4" OD copper, braided
stainless steel or PEX tubing
Water Supply
Pressure
7"
E
INTEGRATED
(178)
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
6"
(152)
75 1/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
RIGHT SIDE
OF OPENING
Electrical supply location.
18" (457)
6" (152)
3" (76)
WINE
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
UNDERCOUNTER
Water supply location.
16
|
Sub-Zero Customer Care 800.222.7820
36" (914)
BUILT-IN REFRIGERATION
BUILT-IN
Custom Panels
For framed, overlay and flush inset applications, custom
door panels must be provided. Handle hardware must
also be provided for overlay and flush inset applications.
Refer to panel requirements below and the charts on pages
20–25 for custom panel dimensions for your specific design
application.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
WEIGHT PER PANEL
BI-36R, BI-36RG, BI-36F
All Other Models
Grille Panel
PANEL THICKNESS
75 lb (34 kg)
50 lb (23 kg)
13 lb (6 kg)
MIN
1/4"
5/8"
(6)
(16)
If the custom panel is thinner than 1/4" (6), a filler material
must be added to achieve a proper fit. If the panel is thicker
than 1/4" (6), rout an edge around the panel or mount the
custom panel on a sheet of 1/4" (6) thick material and insert
into the channel. Refer to the illustrations below.
Routing, recessing or optional extended handles may be
required for finger clearance. Refer to the full-scale template
on page 32.
When installing two units side by side, refer to page 14 for
dual standard installations.
1/4" (6) TRIM REVEAL
1/4" (6) PANEL
DOOR
Panel 1/4" thick or less.
1/4" (6) min
INTEGRATED
Framed
Overlay and Flush Inset
MAX
The framed application is an overlay model with framed
design features. It is not a separate model.
PRO 48
IMPORTANT NOTE: Do not cover a glass door with a solid
panel.
FRAMED PANELS
ROUT TO 1/4" (6)
DOOR
Panel thicker than 1/4".
WINE
UNDERCOUNTER
subzero.com/specs
|
17
BUILT-IN
BUILT-IN REFRIGERATION
PRO 48
Custom Panels
PARTIAL FRAMED OPTION
PANEL MOUNTING KIT
The partial framed kit includes a stainless steel panel for
above and below the external dispenser. Refer to the chart
below for panel width. The kit is avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the
find a showroom section of our website, subzero.com.
A Sub-Zero custom panel mounting kit eliminates the need
for a backer and spacer panel and is avail­able through an
authorized Sub-Zero dealer. For local dealer information, visit
the find a showroom section of our website, subzero.com.
The kit consists of mounting cleats, screws and gages used
to properly position the cleats. The kit is available for all
built-in models except glass door models. Dual installations
require two mounting kits.
PARTIAL FRAMED PANEL
MODEL
BI-42SD
BI-48SD
WIDTH
15 1/16" (383)
18 3/4" (476)
OVERLAY PANELS
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10" (3) spacer panel and a 1/4" (6) backer
panel. Refer to the illustrations below.
INTEGRATED
When installing two units side by side, refer to page 14 for
dual standard installations.
CUSTOM
PANEL
SPACER PANEL
SPACER
PANEL
CUSTOM PANEL
BACKER PANEL
BACKER
PANEL
TRIM
5/16" (8) min
1/8" (3) (OVERLAY)
3/4"
(19)
typical
.10" (3) 1/4" (6)
UNDERCOUNTER
WINE
Panel assembly (cross section). Panel assembly (rear view).
18
|
Sub-Zero Customer Care 800.222.7820
BUILT-IN REFRIGERATION
BUILT-IN
Custom Panels
FLUSH INSET PANELS
ICE AND WATER DISPENSER
The flush inset application is an overlay model with flush
inset panels. It is not a separate model.
For models BI-42SD and BI‑48SD, the refrigerator door
panel must include a cut-out to accommodate the external
dispenser. The thickness of the panel in this area can range
from 1/4" (6) to a maximum of 1 1/8" (29). Refer to the illustrations below.
For flush inset panels thicker than 3/4" (19), a 90° door stop
may be required to prevent interference with adjacent
cabinets. Refer to the full-scale templates at the end of this
guide.
PRO 48
The flush inset design allows custom panels to be installed
flush with adjacent cabinets. Similar to overlay, flush inset
panels are typically created by combining a 3/4" (19) custom
panel, a .10" (3) spacer panel and a 1/4" (6) backer panel.
Refer to the illustrations for overlay panels.
5/8"
3/32"
(16)
(2)
When installing two units side by side, refer to page 15 for
dual flush inset installations.
6 5/16" (160)
1/8" (3)
RADIUS
2"
(51)
HANDLE
INTEGRATED
GLASSWELL
1"
12 7/8"
(25)
(327)
Dispenser dimensions.
Handle placement.
WINE
UNDERCOUNTER
subzero.com/specs
|
19
BUILT-IN
BUILT-IN REFRIGERATION
Framed Panel Dimensions
H H
H H H
H H
A A
H H AH A
A A A
H H
H H H
H AH AH H
A AH A
H H
H H AH A
H H
W W W W W
H H H
INTEGRATED
Door Panel
GRILLE (OPTIONAL)
Grille Panel
H H
BI-36RG
H H H
H H
35 3/4" (908)
69 9/16" (1767)
Door Panel
W
H H H H HH
8 15/16" (227)
FREEZER
35 3/4" (908)
B B
B
A A
10 5/16" (262)
W W W W W
W
FREEZER
Drawer Panel
WINE
GRILLE (OPTIONAL)
Grille Panel
H H
H H H
H H
H H H
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
REFRIGERATOR
Drawer Panel
GRILLE (OPTIONAL)
Grille Panel
W
H
35 3/4" (908)
49 15/16" (1268)
W
H
35 3/4" (908)
18 11/16" (475)
W
H
35 3/4" (908)
8 15/16" (227)
BI-36UG
B B B
A
5 3/16" (132)
Stiles / Rails
MODEL BI-30U, BI-30UG
W W
W W
Door
Panel
W W W WWWW W W W
MODEL BI-36U(ID), BI-36UG
H
A
REFRIGERATOR
H H H
H H H
W
5 3/16A" (132)
A A
Stiles / Rails
H H
W W W W W
BI-30U, BI-36U(ID)
MODEL BI-36R, BI-36RG, BI-36F
REFRIGERATOR / FREEZER
A AH A
H AH AH H
A A A
H H H
W W W W W
BI-36RG
H H
H H H
B B B
W W W W W
BI-36R, BI-36F
H H
A A A
A A A
A A
B B
H H H
H H
A A
PRO 48
H H
H H H
A A A
W
H
3/4W
W 15
W W
W W W 49
W
W/16"
29W
" (756)
(1268)
W
H
29 3/4" (756)
18 11/16" (475)
W
H
29 3/4" (756)
8 15/16" (227)
BI-30UG
Stiles / Rails
A
5 3/16" (132)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PANELS)
Door Panels
FREEZER
Drawer Panel
GRILLE (OPTIONAL)
Grille Panel
W
H
17 5/8" (448)
49 15/16" (1268)
W
H
35 3/4" (908)
18 11/16" (475)
W
H
35 3/4" (908)
8 15/16" (227)
MODEL BI-42UFD(ID)
REFRIGERATOR (2 PANELS)
Door Panels
FREEZER
Drawer Panel
GRILLE (OPTIONAL)
UNDERCOUNTER
Grille Panel
20
|
Sub-Zero Customer Care 800.222.7820
W
H
20 5/8" (524)
49 15/16" (1268)
W
H
41 3/4" (1060)
18 11/16" (475)
W
H
41 3/4" (1060)
8 15/16" (227)
BUILT-IN REFRIGERATION
WW
AA
HH
WW
HH
HH
WW
WW
WW
WW
BUILT-IN
BB
WW
Framed Panel Dimensions
HH
HH
HH
HH
PRO 48
AA
BB
WW
WW
BI-36S, BI-42S, BI-42SID,
BI-48S, BI-48SID
WW
WW
BI-42SD, BI-48SD
MODEL BI-36S
MODEL BI-48S, BI-48SID, BI-48SD
Door Panel
W
H
19 13/16" (503)
69 9/16" (1767)
FREEZER
Door Panel
W
H
15 7/16" (392)
69 9/16" (1767)
GRILLE (OPTIONAL)
Grille Panel
W
H
35 3/4" (908)
8 15/16" (227)
REFRIGERATOR
Door Panel
FREEZER
Door Panel
GRILLE (OPTIONAL)
Grille Panel
BI-48SD
Dispenser Cut-Out*
MODEL BI-42S, BI-42SID, BI-42SD
REFRIGERATOR
Door Panel
FREEZER
Door Panel
GRILLE (OPTIONAL)
BI-42SD
Dispenser Cut-Out*
Cut-Out Location
H
24 13/16" (630)
69 9/16" (1767)
W
H
16 7/16" (418)
69 9/16" (1767)
W
H
41 3/4" (1060)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
1 7/8" (48)
28 3/4" (730)
Cut-Out Location
H
69 9/16" (1767)
W
H
18 3/4" (476)
69 9/16" (1767)
W
H
47 3/4" (1213)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
1 7/8" (48)
28 3/4" (730)
*For models BI-42SD and BI-48SD, panel thickness in the dispenser
area can range from 1/4" (6) to a maximum of 1 1/8" (29). If the panel
is thicker, you must rout out a minimum 1/4" (6) flat landing area to
accommodate the dispenser.
WINE
Grille Panel
W
W
28 1/2" (724)
INTEGRATED
REFRIGERATOR
UNDERCOUNTER
subzero.com/specs
|
21
BUILT-IN
BUILT-IN REFRIGERATION
Overlay Panel Dimensions
H H
H H H
H H
A A
H H AH A
A A A
H H
H H H
H AH AH H
A AH A
H H
H H AH A
H H
W W W W W
INTEGRATED
Overlay Panel
Spacer Panel
Backer Panel
H H
H H H
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
BI-36RG
Stiles / Rails
W W W W W
W W W W W
H H H
H H
WINE
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
H
36" (914)
35 1/8" (892)
35 3/4" (908)
69 3/4" (1772)
68 15/16" (1751)
H 9H H H H
69
/16" (1767)
W
36" (914)
A A A
35 1/8" (892)
3
B B
35 /4" (908)
H
9 1/4" (235)*
A A
8 5/16" (211)
15/16" (227)
B B 8B
A
B
5 1/4" (133)
10 3/8" (264)
W W W W W
W W W W W
W
UNDERCOUNTER
H
50 1/8"
30" (762)
29 1/8" (740)
29 3/4" (756)
49 5/16" (1253)
49 15/16" (1268)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
(1273)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
Stiles / Rails
|
W W W WWWW W W W
H H
H H H
H H
H H H
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
MODEL BI-36U(ID), BI-36UG
W
BI-30UG
22
H H H
H H H
MODEL BI-30U, BI-30UG
REFRIGERATOR
H H
W W W W W
BI-30U, BI-36U(ID)
MODEL BI-36R, BI-36RG, BI-36F
REFRIGERATOR / FREEZER
A AH A
H AH AH H
A A A
H H H
W W W W W
BI-36RG
H H
H H H
B B B
W W W W W
BI-36R, BI-36F
H H
A A A
A A A
A A
B B
H H H
H H
A A
PRO 48
H H
H H H
A A A
Sub-Zero Customer Care 800.222.7820
A
5 1/4" (133)
REFRIGERATOR
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-36UG
A
5 1/4" (133)
Stiles / Rails
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PANELS)
Overlay Panels
Spacer Panels
Backer Panels
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
W
H
17 7/8" (454)
17" (432)
17 5/8" (448)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BUILT-IN REFRIGERATION
WW
AA
HH
WW
HH
HH
WW
WW
WW
WW
BUILT-IN
BB
WW
Overlay Panel Dimensions
HH
MODEL BI-42S, BI-42SID, BI-42SD
HH
REFRIGERATOR
Overlay Panel
Spacer Panel
Backer Panel
HH
HH
BI-36S, BI-42S, BI-42SID,
BI-48S, BI-48SID
WW
W
H
16 11/16" (424)
15 13/16" (402)
16 7/16" (418)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
WW
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-42SD
BI-42SD, BI-48SD
Dispenser Cut-Out
Cut-Out Location
MODEL BI-42UFD(ID)
Overlay Panels
Spacer Panels
Backer Panels
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
H
20 7/8" (530)
20" (508)
20 5/8" (524)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
REFRIGERATOR
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
BI-48SD
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRILLE
Dispenser Cut-Out
W
H
20 1/16" (510)
19 3/16" (487)
19 13/16" (503)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
15 11/16" (398)
14 13/16" (376)
15 7/16" (392)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
Cut-Out Location
W
H
28 3/4" (730)
27 7/8" (708)
28 1/2" (724)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
19" (483)
18 1/8" (460)
18 3/4" (476)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
48" (1219)
47 1/8" (1197)
47 3/4" (1213)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
2" (51)
28 13/16" (732)
*Panel height may be increased by 7/16" (11) to hide upper main
frame. For more information, refer to the built-in panel configurator
at subzero.com/trade/panels.
Grille panel dimensions are for standard 84" (2134) overall unit
height. For 83" (2108) height, subtract 1" (25) from grille panel height
dimensions and for 88" (2235) height, add 4" (102). A specific panel
grille must be ordered for an 83" or 88" overall unit height.
UNDERCOUNTER
Overlay Panel
Spacer Panel
Backer Panel
B
28 13/16" (732)
WINE
Overlay Panel
Spacer Panel
Backer Panel
A
2" (51)
MODEL BI-48S, BI-48SID, BI-48SD
W
MODEL BI-36S
REFRIGERATOR
H
12 7/16" (316)
INTEGRATED
REFRIGERATOR (2 PANELS)
W
5 7/8" (149)
PRO 48
Overlay Panel
Spacer Panel
Backer Panel
BB
WW
H
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
AA
WW
W
25 1/16" (637)
24 3/16" (614)
24 13/16" (630)
subzero.com/specs
|
23
BUILT-IN
BUILT-IN REFRIGERATION
Flush Inset Panel Dimensions
H H
H H H
H H
A A
H H AH A
A A A
H H
H H H
H AH AH H
A AH A
H H
H H AH A
H H
W W W W W
INTEGRATED
Flush Inset Panel
Spacer Panel
Backer Panel
H H
H H H
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36RG
Stiles / Rails
W W W W W
W W W W W
H H H
H H
WINE
Flush Inset Panel
Spacer Panel
Backer Panel
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
UNDERCOUNTER
BI-30UG
Stiles / Rails
24
|
H H H
W W W WWWW W W W
H H
H H H
H H
H H H
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
H H H
MODEL BI-36U(ID), BI-36UG
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
69 3/4" (1772)
68 15/16" (1751)
H 9H H H H
69
/16" (1767)
W
37" (940)
A A A
35 1/8" (892)
3
B B
35 /4" (908)
H
9 1/4" (235)
A A
8 5/16" (211)
15/16" (227)
B B 8B
A
B
5 3/4" (146)
10 3/8" (264)
W W W W W
W W W W W
MODEL BI-30U, BI-30UG
REFRIGERATOR
H H
W W W W W
BI-30U, BI-36U(ID)
MODEL BI-36R, BI-36RG, BI-36F
REFRIGERATOR / FREEZER
H AH AH H
A AH A
B B B
H H H
W W W W W
BI-36RG
H H
H H H
B B B
W W W W W
BI-36R, BI-36F
H H
B B B
A A A
B A
B B
H H H
H H
B A
PRO 48
H H
H H H
A A A
W
H
50 1/8"
31" (787)
29 1/8" (740)
29 3/4" (756)
49 5/16" (1253)
49 15/16" (1268)
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
(1273)
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
Sub-Zero Customer Care 800.222.7820
REFRIGERATOR
Flush Inset Panel
Spacer Panel
Backer Panel
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36UG
Stiles / Rails
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PANELS)
Flush Inset Panels
Spacer Panels
Backer Panels
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
18 3/8" (467)
17" (432)
17 5/8" (448)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
BUILT-IN REFRIGERATION
WW
AA
HH
WW
HH
HH
WW
WW
WW
WW
BUILT-IN
BB
WW
Flush Inset Panel Dimensions
HH
MODEL BI-42S, BI-42SID, BI-42SD
HH
REFRIGERATOR
Flush Inset Panel
Spacer Panel
Backer Panel
HH
HH
BI-36S, BI-42S, BI-42SID,
BI-48S, BI-48SID
WW
W
H
17 3/16" (437)
15 13/16" (402)
16 7/16" (418)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
WW
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
DISPENSER (BI-42SD)
BI-42SD, BI-48SD
Dispenser Cut-Out
Cut-Out Location
MODEL BI-42UFD(ID)
Flush Inset Panels
Spacer Panels
Backer Panels
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
H
21 3/8" (543)
20" (508)
20 5/8" (524)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
REFRIGERATOR
Flush Inset Panel
Spacer Panel
Backer Panel
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
DISPENSER (BI-48SD)
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Cut-Out
W
H
20 9/16" (522)
19 3/16" (487)
19 13/16" (503)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
16 3/16" (411)
14 13/16" (376)
15 7/16" (392)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
Cut-Out Location
W
H
29 1/4" (743)
27 7/8" (708)
28 1/2" (724)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
19 1/2" (495)
18 1/8" (460)
18 3/4" (476)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
49" (1245)
47 1/8" (1197)
47 3/4" (1213)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
2" (51)
28 13/16" (732)
Grille panel dimensions are for standard 84" (2134) overall unit
height. For 83" (2108) height, subtract 1" (25) from grille panel height
dimensions and for 88" (2235) height, add 4" (102). A specific panel
grille must be ordered for an 83" or 88" overall unit height.
UNDERCOUNTER
Flush Inset Panel
Spacer Panel
Backer Panel
B
28 13/16" (732)
WINE
Flush Inset Panel
Spacer Panel
Backer Panel
A
2" (51)
MODEL BI-48S, BI-48SID, BI-48SD
W
MODEL BI-36S
REFRIGERATOR
H
12 7/16" (316)
INTEGRATED
REFRIGERATOR (2 PANELS)
W
5 7/8" (149)
PRO 48
Flush Inset Panel
Spacer Panel
Backer Panel
BB
WW
H
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
AA
WW
W
25 9/16" (649)
24 3/16" (614)
24 13/16" (630)
subzero.com/specs
|
25
BUILT-IN REFRIGERATION
TOP VIEW
TOP VIEW
BUILT-IN
BACKER
CABINETRY
SPACER
BACKER
SPACER
PANEL OFFSET
5/16" (8)
BACKER
SPACER
PRO 48
OVER-AND-UNDER
ILLUS
Door (hinge) / Drawer / Grille Sides
Doors (handle) Sides (French door only)
Grille Top
Grille Bottom / Door Top
Door Bottom / Drawer Top
Drawer Bottom
SIDE-BY-SIDE
ILLUS
Doors (hinge) / Grille Sides
Doors (handle) Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
GRILLE
A
CABINETRY
B
C
D
F
GRILLE
1/2"
(13)
CABINETRY
5/8"
(16)
5/8"
(16)
5/16" (8)
1/2"
(13)
CABINETRY
1/2" (13)
5/8"
(16)
1/2"
(13)
1/8"
5/16" (3) GRILLE
(8)
CABINETRY
1/2" (13)
1/8"
5/16VIEW
SIDE
" (3)GRILLE
(8)
CABINETRY
1/2" (13)
1/8"
5/16
" (3)
GRILLE
SIDE
VIEW
(8)
WINE
5/16"
5/32
3/DRAWER
(8)
"32"
5/16" (4)(2)
(8)
DOOR
/8" (16)
5/16"
DRAWER
35//32
(8)
Illus.
32"E
"
5/16" (2)
(4)
(8) DOOR
UNDERCOUNTER
5/8" (16)
SIDE VIEW
DRAWER
5/DRAWER
32"
5/16" (4)
(8)
SIDE VIEW
26
|
Sub-Zero Customer Care 800.222.7820
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1/8" (3)
DOOR
1/4" (6)
1/4" (6)
REVEAL
5/16" (8)
5/16" (8)
1/8" (3)
1/8" (3)
1/4" (6)
REVEAL
1/2" (13)
5/16" DOOR
3/32
5/"32GRILLE
"
5/16(8)
" (2)(4)
(8)
DOOR
GRILLE
5/16"
35/32"
/32"
5/(8)
16" (2)
(4)
(8)
SIDE VIEW
SIDE VIEW
1/2" (13)
1/2
5/16"
DOOR
GRILLE
32
(8) 53//32
""
5/16" (4)
(2)
(8)
DOOR
GRILLE
1/8"
5/16
" (3)
SIDE
VIEW
(8)
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
SIDE VIEW
SIDE VIEW
1/2" (13)
Illus.DOOR
D
SIDE VIEW
1/2
1/2" (13)
1/8"
5SIDE
VIEW
/16" (3)
(8)
1/2" (13)
5/16"
(8) 5/32"
(4)
5/16"
(8) 5/32" GRILLE
(4)
GRILLE
1/8"
5/16" (3)
(8)
1/2" (13)
REVEAL
1/2
DOOR
3/32"
5/16" (2)
(8)
SIDE VIEW
DOOR /
DRAWER
3/32"
5/16" (2)
(8)
DOOR /
DRAWER
SIDE VIEW
DOOR
SIDE VIEW
5
DOOR
TOP VIEW REVEAL
5/16"
(8) 3/32"
(2)
5/8" (16)
DRAWER
TOP VIEWREVEAL
Illus. B
SIDE VIEW
DOOR
DOOR
1/4" (6)
1/4" (6)
1/4" (6)
Illus. A
5/16"
(8) 3/32"
(2)
DRAWER
1/8" (3)
DOOR
DOOR
1/8DOOR
" (3)
REVEAL
Illus. C
DOOR
5/16" (8)
5/16" (8)
FLUSH INSET PANEL
A
5/16
" (8)
A
B
GRILLE C
CABINETRY
D
E
F
5/CABINETRY
8"
(16)
5/16" (8)
BACKER
CABINETRY
FLUSH
INSET PANEL
ILLUS
C
D
CABINETRY
F
1/2"
(13)
TOP VIEW
5/8"
SPACER
(16)
Door / Grille Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
1/2"
(13)
PANEL OFFSET
ALL REFRIGERATOR / ALL FREEZER
5/16" (8)
BACKER
5/8"CABINETRY
SPACER
TOP VIEW (16)
BACKER
SPACER
TOP VIEW
DOOR
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
1/2"
(13)
The illustrations provide panel offsets and reveals for built-in
models in a flush inset application. Refer to the chart below
5/16" (8)
for reference to the illustrations.
DOOR DOOR
DOOR
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
INTEGRATED
CABINETRY
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
Flush Inset Panels
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
DOOR / DRAWER / GRILLE
5/8" (16)
DOOR /
DRAWER
5/16"
(8)
DOOR /
DRAWER
5/16"
(8)
5/16"
(8) 53/32"
5/16" (4)
(2)
(8)
SIDE VIEW
5
SIDE VIEW
DOOR /
DRAWER
/8" (16)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
3/32"
(2)
SIDE VIEW
5/16"
DOOR /
(8) DRAWER
3
5/16"
(8)
Illus. F
SIDE VIEW
3/32"
5/16" (2)
(8)
3
SIDE VIEW
5/16"
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
3/32"
(2)
3
SIDE VIEW
BUILT-IN REFRIGERATION
BUILT-IN
Dual Installation
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the charts on pages
20–23. Panel dimensions and offsets for dual flush inset
installations are listed on the following pages.
PRO 48
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between units.
A custom filler strip is required when installing two French
door or side-by-side models. Dual installations without a
filler strip can only be accomplished using two units with
opposite hinges. Refer to the illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
INTEGRATED
WITHOUT FILLER STRIP
Opposite hinges.
FILLER STRIP
Same side hinges.
WINE
UNDERCOUNTER
subzero.com/specs
|
27
BUILT-IN
BUILT-IN REFRIGERATION
Dual Flush Inset Panel Dimensions
H H
H H
H H
H H
H H
H H A AH AH A
A AH H
W W
W W
BI-36R, BI-36F
B B
H H
W W
W W
W W
W W
BI-36RG
H H
H H
INTEGRATED
W
H
36 1/2" (927)
35 1/8" (892)
H
35 3/4H" (908)
69 3/4" (1772)
68 15/16" (1751)
H 9H
69
/16" (1767)
GRILLE
W
36 1/2" (927)
A A
35 1/8" (892)
3
B B
35 /4" (908)
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36RG
Stiles / Rails
W W
W W
W W
A
B
5 3/4" (146)
10 3/8" (264)
W
W
WW
W W
WINE
REFRIGERATOR
W W
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
BI-30UG
Stiles / Rails
28
|
W
30 1/2"
(775)
29 1/8" (740)
29 3/4" (756)
H
H
50 1/8"
(1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
Flush Inset Panel
Spacer Panel
H
Backer
Panel
FREEZER
B
W W
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
Sub-Zero Customer Care 800.222.7820
REFRIGERATOR
H
9 1/4" (235)
A A
8 5/16" (211)
15
8 /16" (227)B
MODEL BI-30U, BI-30UG
Flush Inset Panel
Spacer Panel
Backer Panel
H H
H H
W W
W W
W W
W W
W W
H H
H H
W W
BI-30UG, BI-36UG
MODEL BI-36U(ID), BI-36UG
REFRIGERATOR / FREEZER
H H
A AH H
H H
H H
MODEL BI-36R, BI-36RG, BI-36F
Flush Inset Panel
Spacer Panel
Backer Panel
H H
H H
H H
W W
BI-30U, BI-36U(ID)
H H
W W
B B
B A
B B
H H
B B
H H A AH AH A
A A
H H
H H
UNDERCOUNTER
H H
B A
PRO 48
A A
H H
H H
A A
A A
Flush Inset Panel
Spacer Panel
Backer Panel
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36UG
Stiles / Rails
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
Grille panel dimensions are for standard 84" (2134) overall unit
height. For 83" (2108) height, subtract 1" (25) from grille panel height
dimensions and for 88" (2235) height, add 4" (102). A specific panel
grille must be ordered for an 83" or 88" overall unit height. For dual
wide grilles, refer to page 30.
BUILT-IN REFRIGERATION
TOP VIEW
TOP VIEW
CABINETRY
TOP VIEW
Dual Installation
DUAL FLUSH INSET PANEL OFFSET
BACKER
5/8"CABINETRY
(16) SPACER
ILLUS
Door (hinge) / Grille Sides
Door (handle) Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
A
B
C
CABINETRY
D
F
OVER-AND-UNDER
ILLUS
A
B
CABINETRY
C
D
E
F
GRILLE
TOP VIEW
5/CABINETRY
8"
(16)
5/16" (8)
1/2"
(13)
BACKER
1/2"
(13)
CABINETRY
5/8"
(16)
5/16" (8)
CABINETRY
1/2" (13)
5/8"
(16)
1/2"
(13)
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1
/8" (3)
DOOR
1/4" (6)
1/4" (6)
REVEAL
1/8" (3)
1/8" (3)
CABINETRY
1/2" (13)
1/8"
5/16VIEW
SIDE
" (3)GRILLE
CABINETRY
1/4" (6)
REVEAL
REVEAL
1/2" (13)
1/8"
5/16" (3)
(8)
1/2" (13)
1/2
1/2" (13)
5/16" DOOR
3/32
5/"32GRILLE
"
5/16(8)
" (2)(4)
(8)
DOOR
GRILLE
1/8"
5SIDE
VIEW
/16" (3)
(8)
5/16"
35/32"
/32"
5/(8)
16" (2)
(4)
(8)
SIDE VIEW
SIDE VIEW
1/2" (13)
DOOR
1/2
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
DOOR
3/32
GRILLE
"
5/16" (2)
(8)
1/8"
5/16
" (3)
SIDE
VIEW
(8)
SIDE VIEW
SIDE VIEW
1/2
DOOR
Illus. D
SIDE VIEW
5/16"
(8) 5/32"
(4)
5/16"
(8) 5/32" GRILLE
(4)
GRILLE
Illus. B
1/8"
5/16" (3) GRILLE
(8)
(8)
5/16" (8)
5/16" (8)
1/4" (6)
Illus. A
3/32"
5/16" (2)
(8)
DOOR /
DRAWER
DOOR /
DRAWER
SIDE VIEW
5/16"
(8) 3/32"
(2)
5/16"
(8) 3/32"
(2)
DOOR
5/16"
5/32
3/DRAWER
(8)
"32"
5/16" (4)(2)
(8)
DOOR
SIDE VIEW
5
/8" (16)
5/DRAWER
Illus.
32E
"
5/16" (4)
(8) DOOR
SIDE VIEW
DOOR /
DRAWER
5/16"
(8)
DOOR /
DRAWER
5/16"
(8) 53/32"
5/16" (4)
(2)
(8)
SIDE VIEW
5
SIDE VIEW
/8" (16)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
3/32"
(2)
SIDE VIEW
5/16"
DOOR /
(8) DRAWER
5/16"
(8)
3
5/16"
(8)
Illus. F
SIDE VIEW
3/32"
(2)
3
SIDE VIEW
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
subzero.com/specs
|
29
5/16"
(8)
UNDERCOUNTER
DRAWER
5/8" (16)
WINE
5/8" (16)
DRAWER
TOP VIEW REVEAL
TOP VIEWREVEAL
REVEAL
Illus. C
DOOR
DOOR
1/4" (6)
1/4" (6)
FLUSH INSET PANEL
GRILLE
SIDE VIEW
DRAWER
1/8" (3)
DOOR
DOOR
1/8DOOR
" (3)
DUAL
TRIM
1/2" (13)
DOOR
5/16" (8)
5/16" (8)
INTEGRATED
GRILLE
TOP VIEW
PRO 48
ALL REFRIGERATOR / ALL FREEZER
1/2"
(13)
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
5/8"
SPACER
(16)
PANEL OFFSET
Door (hinge) / Drawer / Grille Sides
Door (handle) Sides
Grille Top
Grille Bottom / Door Top
Door Bottom / Drawer Top
Drawer Bottom
5/16" (8)
1/2"
(13)
The illustrations provide panel offsets and reveals for
built-in
FLUSH
INSET PANEL
models in a dual flush inset application. Refer to the chart
5/16" (8)
below for reference to the illustrations.
TOP VIEW
DOOR
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
5/16" (8)
BACKER
SPACER
DOOR DOOR
DOOR
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
BUILT-IN
BACKER
CABINETRY
SPACER
BACKER
SPACER
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
DOOR / DRAWER / GRILLE
3
BUILT-IN
BUILT-IN REFRIGERATION
Dual Installation
DUAL WIDE GRILLE
DUAL WIDE GRILLE—FLUSH INSET
A dual wide grille spans the entire width of both units in a
dual installation and is a part of a dual installation kit.
TWO 30" MODELS
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
61 1/4" (1556)
59 3/8" (1508)
60" (1524)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
PRO 48
For overlay and flush inset panel dimensions for the dual
wide grille, refer to the charts below. Dimensions listed are
for a standard 84" (2134) finished height.
DUAL WIDE GRILLE—OVERLAY
TWO 30" MODELS
Overlay Panel
Spacer Panel
Backer Panel
30" AND 36" MODEL
Overlay Panel
Spacer Panel
Backer Panel
Overlay Panel
Spacer Panel
Backer Panel
|
W
H
67 1/4" (1708)
65 3/8" (1661)
66" (1676)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
TWO 36" MODELS
W
H
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
Flush Inset Panel
Spacer Panel
Backer Panel
73 1/4" (1861)
71 3/8" (1813)
72" (1829)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
66 1/4" (1683)
65 3/8" (1661)
66" (1676)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
72 1/4" (1835)
71 3/8" (1813)
72" (1829)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
UNDERCOUNTER
30
Flush Inset Panel
Spacer Panel
Backer Panel
60 1/4" (1530)
59 3/8" (1508)
60" (1524)
WINE
INTEGRATED
TWO 36" MODELS
30" AND 36" MODEL
Sub-Zero Customer Care 800.222.7820
BUILT-IN REFRIGERATION
BUILT-IN
Standard Handles
The custom side panels must be a minimum of 24" (610)
deep and 1/2" (13) thick. Routing will be necessary for the
side panel to fit flush against the side of the unit. Refer to
the illustrations below.
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
When installing a built-in unit with a custom side panel, an
accessory kit is required. Stainless steel and white enamel
side panels are available through an authorized Sub-Zero
dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.
Refer to the chart below for standard handle lengths for
built-in models.
HANDLE LENGTH
BUILT-IN
Full Door
Over-and-Under Door
30" Drawer
36" Drawer
42" Drawer
24" (610)
FRONT
OF SIDE
PANEL
TUBULAR
PRO
63 7/8" (1622)
44 1/4" (1124)
24 5/16" (633)
30 5/16" (770)
36 5/16" (922)
45 3/16" (1147)
37 1/2" (952)
17 9/16" (447)
23 5/8" (600)
29 5/8" (753)
PRO 48
Side Panel
1" (25)
1 7/8" (48)
INTEGRATED
1/8" (3)
1/2" (13)
ROUT TO 1/8" (3)
1 7/8"(48)
84"
1" (25)
MAIN
FRAME
SIDE PANEL
ROUTING
(2134)
Routing detail.
4 1/4" (108)
ROUT TO
3/16" (5)
(OVER-AND-UNDER
MODELS)
5 3/4"
(146)
20 1/2"
(521)
WINE
4" (102)
OPTIONAL
TOE KICK
CUT-OUT
2 5/8"
(67)
Side panel dimensions.
UNDERCOUNTER
subzero.com/specs
|
31
BUILT-IN
BUILT-IN REFRIGERATION
Framed Panels
PRO 48
FULL-SCALE TEMPLATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
INTEGRATED
STANDARD
FULL-LENGTH HANDLE
2"
1"
(51)
(25)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
1/2" (13) PANEL
WINE
1/4" (6) FRAMED PANEL
DOOR
UNDERCOUNTER
Framed panel thickness.
32
|
Sub-Zero Customer Care 800.222.7820
BUILT-IN REFRIGERATION
BUILT-IN
Overlay and Flush Inset Panels
FULL-SCALE TEMPLATE
Overlay and flush inset panels must be a minimum of 5/8"
(16) thick to support mounting the handle. Panel thickness
does not include backer and spacer panel. Mount handle
close to the opening edge of the door.
PRO 48
DEPTH OF TUBULAR
AND PRO HANDLES
2"
(51)
3"
INTEGRATED
1"
(25)
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
.10" (3) SPACER PANEL
1/4" (6) BACKER PANEL
WINE
DOOR
Overlay and flush inset panel thickness.
UNDERCOUNTER
subzero.com/specs
|
33
BUILT-IN
BUILT-IN REFRIGERATION
Overlay Application
FULL-SCALE TEMPLATE
237/8" (606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
PRO 48
0" (0)
1/4" (6)
1/2" (13)
3/4" (19)
1" (25)
11/4" (32)
11/2" (38)
13/4" (44)
INTEGRATED
2" (51)
21/4" (57)
21/2" (63)
23/4" (70)
3" (76)
31/4" (83)
31/2" (89)
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
OVERLAY PANEL
(TYPICAL)
1/4" (6) BACKER
UNDERCOUNTER
PANEL
0"
1" (25)
SCALE
90° door opening (top view).
34
|
Sub-Zero Customer Care 800.222.7820
BUILT-IN REFRIGERATION
BUILT-IN
Flush Inset Application
FULL-SCALE TEMPLATE
24" (610)
TO BACK WALL
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
1 1/4" (32)
PRO 48
2 3/16" (56)
ASSUMES
3/4" (19)
FLUSH INSET
PANEL
THICKNESS
INTEGRATED
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1/4" (6) BACKER
PANEL
0"
1" (25)
UNDERCOUNTER
SCALE
110° door opening (top view).
subzero.com/specs
|
35
BUILT-IN
BUILT-IN REFRIGERATION
PRO 48
FILLER STRIP
11/4" (32)
DOOR
CLOSED
WINE
INTEGRATED
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
Dual Standard Installation
FULL-SCALE TEMPLATE
Typical framed, overlay or stainless steel dual installation
with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
UNDERCOUNTER
0"
1" (25)
SCALE
Dual standard installation (top view).
36
|
Sub-Zero Customer Care 800.222.7820
DOOR
OPEN 110°
BUILT-IN REFRIGERATION
BUILT-IN
FILLER STRIP
PRO 48
1 1/2" (38)
1/2" (13)
PROFILE OF 3/4" (19) FLUSH INSET PANEL
AND TUBULAR HANDLE
DOOR
CLOSED
INTEGRATED
WINE
Dual Flush Inset Installation
DOOR
OPEN 110°
FULL-SCALE TEMPLATE
Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
0"
1" (25)
UNDERCOUNTER
SCALE
Dual flush inset installation (top view).
subzero.com/specs
|
37
PRO 48 REFRIGERATION
BUILT-IN
PRO 48 Refrigeration
PRO 48 MODELS
KEY FEATURES
•Can be used freestanding or installed as a standard or
flush built-in application.
•Stainless steel interior as well as exterior.
•Handles coordinate with handles of Wolf ranges.
•Dual refrigeration system enhanced with triple evaporators allow independent control of storage conditions in
refrigerator cabinet and drawer compartments.
PRO 48
Freshness finds unmistakable expression in the Sub-Zero
PRO 48. An 800-pound monument to food preservation—
equal parts sculpted metal design statement and culinary
secret weapon. Its vast interior, like its bold exterior, is
crafted of stainless steel. The PRO 48 is available with
or without a glass door and may be either built in or
freestanding.
•Advanced water filtration system.
•Slide-out stainless steel bins fit neatly under refrigerator
glass shelves.
•Exterior temperature display.
•Flip-up grille provides easy access for quick routine
maintenance.
648PRO
INTEGRATED
•Star-K certified.
648PROG
WINE
UNDERCOUNTER
subzero.com/specs
|
39
BUILT-IN
PRO 48 REFRIGERATION
Overall Dimensions
PRO 48
25 7/8" (657)
PRO 48
48" (1219)
84"
(2134)
42 1/8"
(1070)
30 1/2"
INTEGRATED
(775)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
30 3/16" (767)
23 7/8"
(606)
14 1/2"
(368)
21"
(533)
30 3/4"
WINE
(781)
SPECIFICATIONS
INTERIOR CAPACITY
R CU FT (L)
F CU FT (L)
648PRO, 648PROG
18.4 (521)
11.7 (331)
SHIPPING WEIGHT
2 3/8" (60)
UNDERCOUNTER
Model 648PRO and 648PROG.
40
|
Sub-Zero Customer Care 800.222.7820
648PRO
648PROG
LB (KG)
860 (390)
875 (397)
PRO 48 REFRIGERATION
BUILT-IN
Opening Dimensions
STANDARD AND FLUSH INSTALLATION
D
OPENING
DEPTH
PRO 48
TOP VIEW
INTEGRATED
W
H
OPENING WIDTH
OPENING
HEIGHT
SIDE VIEW
FRONT VIEW
WINE
OPENING DIMENSIONS
INSTALLATION
Standard
Flush
W
H
D
47 1/2" (1206)
48" (1219)
83 3/4" (2127)
84 1/8" (2137)
24" (610)
26" (660)
For standard built-in installations, the face frame of the unit
will extend 2" (51) beyond cabinetry. For flush installations,
the front of the face frame will be flush with surrounding
cabinetry.
UNDERCOUNTER
subzero.com/specs
|
41
BUILT-IN
PRO 48 REFRIGERATION
Electrical
Plumbing
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause interruption of operation.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self‑piercing valves.
The water supply line must not interfere with installation of
the anti-tip bracket.
PRO 48
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
15 amp
Receptacle
3-prong grounding-type
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
1/4" OD copper, braided
stainless steel or PEX tubing
Water Supply
Pressure
7"
E
INTEGRATED
(178)
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
6"
(152)
75 1/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
RIGHT SIDE
OF OPENING
Electrical supply location.
6"
(152)
5 3/16"
(132)
3" (76)
WINE
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
UNDERCOUNTER
Water supply location.
42
|
Sub-Zero Customer Care 800.222.7820
36" (914)
PRO 48 REFRIGERATION
BUILT-IN
Standard Handles
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
PRO 48 models.
PRO 48
HANDLE LENGTH
PRO 48
Door
Refrigerator Drawer
Freezer Drawer
TUBULAR
PRO
NA
NA
NA
27 11/16" (703)
19 15/16" (506)
11 9/16" (294)
INTEGRATED
WINE
UNDERCOUNTER
subzero.com/specs
|
43
INTEGRATED REFRIGERATION
BUILT-IN
Integrated Refrigeration
With custom front panels and hardware, Sub-Zero invented
integrated columns, tall and drawer models that disappear
into the decor. Integrated units fit flush with other cabinets,
making integrated refrigeration as practical and beautiful in
the master suite, bar or theatre room as in the kitchen.
KEY FEATURES
•Custom front panels and hardware allow for infinite
design options.
•Point-of-use refrigeration that can be placed anywhere in
the home.
PRO 48
•Dual refrigeration; two compressors preserve food’s
goodness in self-contained compartments.
•Energy efficient; many models are ENERGY STAR®
qualified.
•Star-K certified.
INTEGRATED MODELS
INTEGRATED
IC-18FI
IC-24R,
IC-24FI
IC-30R(ID),
IC-30FI
IC-36R(ID)
IT-30R(ID),
IT-30FI, IT-30CI(ID)
IT-36R(ID),
IT-36CI(ID)
WINE
ID-24R,
ID-24F(I)
ID-27R
ID-30R(P),
ID-30F(I), ID-30C(I)
ID-36R(P),
ID-36C(I)
UNDERCOUNTER
subzero.com/specs
|
45
BUILT-IN
INTEGRATED REFRIGERATION
Specifications
Overall Dimensions
COLUMN
INTERIOR CAPACITY
PRO 48
COLUMN
IC-18FI
IC-24R
IC-24FI
IC-30R(ID)
IC-30FI
IC-36R(ID)
TALL
ID-24R
ID-24F(I)
ID-27R
ID-30R(P)
ID-30F(I)
ID-30C(I)
ID-36R(P)
ID-36C(I)
8.4 (238)
W
24" (610)
4 1/2" (114)
12.3 (348)
17.3 (490)
15.3 (433)
21.4 (606)
F CU FT (L)
10.6 (300)
20.5 (580)
13.3 (377)
R CU FT (L)
69 1/2"
84"*
16.5 (467)
15.1 (428)
5.0 (142)
(2134)
(1765)
6.4 (181)
F CU FT (L)
4.0 (113)
3.8 (108)
4.6 (130)
5.2 (147)
3.0 (85)
6.6 (187)
3.4 (96)
4.9 (139)
2.0 (57)
2.5 (71)
SHIPPING WEIGHT
COLUMN
18" Column
24" Column
30" Column
36" Column
TALL
LB (KG)
260 (118)
340 (154)
400 (181)
440 (200)
DRAWER
24" Drawer
27" Drawer
30" Drawer
36" Drawer
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
A
LB (KG)
30" Tall
36" Tall
WINE
F CU FT (L)
12.9 (365)
R CU FT (L)
IT-30R(ID)
IT-30FI
IT-30CI(ID)
IT-36R(ID)
IT-36CI(ID)
DRAWER
INTEGRATED
R CU FT (L)
13/4" (45)
400 (181)
460 (209)
LB (KG)
170 (77)
190 (86)
210 (95)
250 (113)
B
IMPORTANT NOTE: Overall dimensions do not include panels
or handles. Dimensions will vary with panel thickness.
COLUMN
MODEL
UNDERCOUNTER
18" Column
24" Column
30" Column
36" Column
46
|
Sub-Zero Customer Care 800.222.7820
W
A
B
18" (457)
24" (610)
30" (762)
36" (914)
2 1/2" (64)
4" (102)
5 5/8" (143)
7 1/4" (184)
16 1/2" (419)
22 1/2" (572)
28 1/2" (724)
34 1/2" (876)
INTEGRATED REFRIGERATION
BUILT-IN
Overall Dimensions
TALL
DRAWER
W
W
24" (610)
24" (610)
1/4" (6)
4 1/2" (114)
13 5/16"
(338)
(876)
3/8" (10)
10 9/16"
(268)
44 7/8"
84"*
(2134)
PRO 48
34 1/2"*
(1140)
3 5/8" (92)
*34" (864) MIN TO 35" (889) MAX
3/8" (10)
13 5/16"
(338)
3/8" (10)
INTEGRATED
10 9/16"
(268)
18 3/8"
(467)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
DRAWER
A
MODEL
13/4" (45)
24" Drawer
27" Drawer
30" Drawer
36" Drawer
WINE
18 3/8"
W
24" (610)
27" (686)
30" (762)
36" (914)
B
(467)
TALL
W
A
B
30" Tall
36" Tall
30" (762)
36" (914)
5 5/8" (143)
7 1/4" (184)
28 1/2" (724)
34 1/2" (876)
UNDERCOUNTER
MODEL
subzero.com/specs
|
47
BUILT-IN
INTEGRATED REFRIGERATION
Opening Dimensions
INTEGRATED
OPENING DIMENSIONS
COLUMN AND TALL
18" Column
24" Column
30" Column and Tall
36" Column and Tall
PRO 48
25" (635)
OPENING
DEPTH
DRAWER
TOP VIEW
H
84" (2134)
84" (2134)
84" (2134)
84" (2134)
W
H
24" (610)
27" (686)
30" (762)
36" (914)
34 1/2" (876)
34 1/2" (876)
34 1/2" (876)
34 1/2" (876)
INTEGRATED
The depth of each integrated model is 24" (610). Allow for
panel thickness when planning the finished opening depth.
A minimum 3 1/2" (89) finished return is required on all sides
of the opening. Framed cabinets will require additional
finished filler material behind the face frame for a proper
installation. Refer to the illustration.
H
W
OPENING
HEIGHT
OPENING WIDTH
DUAL INSTALLATION
When installing two units side by side in a dual installation, the opening width is the width of the two units added
together. A dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum
2" (51) filler strip is required between units.
SIDE VIEW
WINE
24" Drawer
27" Drawer
30" Drawer
36" Drawer
W
18" (457)
24" (610)
30" (762)
36" (914)
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4"
3 1/2" (89)
(19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
FINISHED
RETURN
W
W
FRAMED CABINETRY
UNDERCOUNTER
FRAMELESS CABINETRY
48
|
FILLER
Sub-Zero Customer Care 800.222.7820
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
INTEGRATED REFRIGERATION
BUILT-IN
Electrical
Plumbing
The electrical supply must be located within the shaded
area shown in the illustration and chart below. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self‑piercing valves.
The water supply line must not interfere with installation of
the anti-tip bracket.
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
PRO 48
The electrical outlet must be positioned with the grounding
prong to the right of the thinner blades.
Installation must comply with all applicable plumbing codes.
15 amp
Receptacle
3-prong grounding-type
ELECTRICAL SUPPLY LOCATION
MODEL
A
6" (152)
9 1/2"
1/4" OD copper, braided
stainless steel or PEX tubing
Water Supply
Pressure
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
36" (914)
(241)
11" (279)
12 1/2" (318)
15 1/2" (394)
WATER SUPPLY LOCATION
MODEL
A
18" Model
24" Model
30" Model
36" Model
3" (76)
5 1/2" (140)
6" (152)
9" (229)
INTEGRATED
18" Model
24" Model
27" Model
30" Model
36" Model
PLUMBING REQUIREMENTS
LEFT SIDE
OF OPENING
41/2"
(114)
RIGHT SIDE
OF OPENING
A
4 1/4"
1/4" (6)
A
WINE
(108)
FLOOR
6" (152)
3" (76)
Electrical supply location.
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Water supply location.
UNDERCOUNTER
subzero.com/specs
|
49
BUILT-IN
INTEGRATED REFRIGERATION
Custom Panels
PRO 48
For integrated models, custom door panels and handle
hardware must be provided. Refer to the panel requirements
chart and typical panel dimensions.
TYPICAL PANEL DIMENSIONS
The thickness of the custom panel can vary. A minimum
5/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each integrated model is 24" (610). Allow for panel
thickness when planning the finished opening depth. Refer
to the full-scale template on page 53.
79 7/8"
49 3/8"
(2029)
(1254)
13 9/16"
(345)
CAUTION
16 11/16"
As reveals between cabinetry and the unit decrease,
severe finger pinching can occur while door is closing.
(424)
INTEGRATED
W
W
Finish all sides of custom panels. They will be visible when
the door/drawer is open.
Column
D-style handles are recommended. Door handles must be
located near the edge of the panel opposite the hinge and
should be centered top to bottom. Drawer handles must
be located near the top edge of each panel. Stainless steel
tubular and pro handles are avail­able through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com.
Typical panel dimensions are based on an 84" (2134) finished
height for column and tall models and 34 1/2" (876) for drawer
models, with a 4" (102) toe kick and 1/8" (3) reveals. Panel
dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the
chart below for panel widths.
WEIGHT PER PANEL
18" Column
24" Column
30" Column
36" Column
WEIGHT PER PANEL
30" Tall (door)
36" Tall (door)
Drawer
PANEL THICKNESS
All Panels
Tall
Drawer
PANEL WIDTH
PANEL REQUIREMENTS
WINE
W
MAX
45 lb (20 kg)
60 lb (27 kg)
75 lb (34 kg)
75 lb (34 kg)
MODEL
18" Model
24" Model
27" Model
30" Model
36" Model
W
17 3/4" (451)
23 3/4" (603)
26 3/4" (679)
29 3/4" (756)
35 3/4" (908)
MAX
50 lb (22 kg)
60 lb (27 kg)
15 lb (7 kg)
MIN
5/8"
(16)
DUAL INSTALLATION
For dual installations, refer to the illustration for panel
heights and the chart below for panel widths.
PANEL WIDTH
MODEL
UNDERCOUNTER
18" Model
24" Model
27" Model
30" Model
36" Model
50
|
Sub-Zero Customer Care 800.222.7820
W
17 13/16" (452)
23 13/16" (605)
26 13/16" (681)
29 13/16" (757)
35 13/16" (910)
INTEGRATED REFRIGERATION
BUILT-IN
Custom Panels
TOE KICK CLEARANCE
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below. Toe kick heights from
2" (51) to 3 7/8" (98) require a reduced toe kick accessory
available through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.
1 3/4"
(45)
PRO 48
DOOR PANEL HEIGHT
A DECORATIVE VALANCE
CANNOT EXTEND
BEYOND THIS PLANE
1/8" (3)
DOOR
PANEL
84"
24" (610)
(2134)
TO BACK OF UNIT
HINGE**
VENTED
LOUVERS
24" (610)
TO BACK OF UNIT
HINGE
INTEGRATED
DOOR
PANEL
1 1/8" (29)
MAX
TOE KICK
ADJUSTMENT
2" (51)*
TO
6" (152)
FROM
FLOOR
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
Upper valance—column and tall (side view).
*2" (51) to 3 7/8" (98) requires sales accessory.
**Column models only.
WINE
Toe kick (side view).
UNDERCOUNTER
subzero.com/specs
|
51
BUILT-IN
INTEGRATED REFRIGERATION
Standard Handles
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
PRO 48
Refer to the chart below for standard handle lengths for
integrated models.
HANDLE LENGTH
INTEGRATED
TUBULAR
PRO
50 1/8" (1273)
33 1/4" (845)
21 1/4" (540)
24 1/4" (616)
27 1/4" (692)
33 1/4" (845)
48 3/8" (1229)
31 1/2" (800)
19 1/2" (495)
22 1/2" (572)
25 1/2" (648)
31 1/2" (800)
UNDERCOUNTER
WINE
INTEGRATED
Column Door
Tall Door
24" Drawer
27" Drawer
30" Drawer
36" Drawer
52
|
Sub-Zero Customer Care 800.222.7820
INTEGRATED REFRIGERATION
BUILT-IN
Maximum Door Opening
FULL-SCALE TEMPLATE
As the panel width and/or depth increases, so does the
potential for panel interference. Interference may be
minimized by utilizing the 90° door stop.
PRO 48
3/4" (19) PANEL
DOOR OPEN
MAXIMUM 105°
1/8" (3) REVEAL
INTEGRATED
POTENTIAL
INTERFERENCE
DOOR CLOSED
3/4" (19) PANEL
ADJACENT
CABINETRY
WINE
POTENTIAL INTERFERENCE
0"
1" (25)
UNDERCOUNTER
SCALE
Maximum door opening (top view).
subzero.com/specs
|
53
WINE STORAGE
BUILT-IN
Wine Storage
Wine finds a well-deserved place of honor in a Sub-Zero
wine storage unit. Every detail is designed to ensure better
wine preservation. Cherrywood-faced racks, soft lighting,
custom cabinetry if desired—Sub-Zero helps make a wine
collection an element of beauty in the home.
KEY FEATURES
•Integrated, overlay, flush inset and stainless steel design
options.
•Full-view glass door standard on all models.
•Two independent storage zones maintain temperature,
humidity and UV protection.
PRO 48
•Discreet interior lighting with illuminated display rack for
prized bottles of wine.
•Full extension, cherrywood-faced wine racks for easy
access.
•Wine racks accommodate 750 ml bottles, half-bottles
and magnums.
•Inventory system helps organize wine collection.
•Freestanding model 424FSG does not require panels or
surrounding cabinetry.
424G
424FSG
IW-18
IW-24
IW-30
WINE
315W
INTEGRATED
•Model IW-30R features two refrigerator storage drawers.
WINE STORAGE MODELS
IW-30R
WS-30
UNDERCOUNTER
subzero.com/specs
|
55
BUILT-IN
WINE STORAGE
Overall Dimensions
MODEL 315W
MODEL 424G
15 1/8" (384)
23 7/8" (606)
24" (610)
PRO 48
341/16"
34"
(865)
(864)
4" (102)
INTEGRATED
24" (610)
4" (102)
16 5/8"
(422)
25 3/8"
(645)
1 3/4" (44)
1 3/4" (44)
SPECIFICATIONS
WINE
STORAGE CAPACITY
315W
424G
424FSG
SHIPPING WEIGHT
UNDERCOUNTER
315W
424G
424FSG
56
|
Sub-Zero Customer Care 800.222.7820
BOTTLES (750 ML)
26
46
46
LB (KG)
118 (54)
195 (88)
220 (100)
Overall dimensions are based on the stainless steel model.
Refer to page 77 for door clearance information.
WINE STORAGE
BUILT-IN
Overall Dimensions
Opening Dimensions
MODEL 424FSG
MODEL 315W AND 424G
24 1/4" (616)
24 5/8" (625)
24" (610)
OPENING
DEPTH
PRO 48
34 3/16"
(868)
TOP VIEW
4" (102)
W
(876)
OPENING
HEIGHT
OPENING WIDTH
SIDE VIEW
INTEGRATED
25 3/8"
34 1/2"
FRONT VIEW
(645)
1 3/4" (44)
OPENING WIDTH
MODEL
315W
424G
Freestanding model 424FSG has a finished stainless steel
exterior and handles.
W
15 1/4" (387)
24" (610)
DUAL OPENING WIDTH
MODELS
Two 24" Models
W
48 1/8" (1222)
WINE
Dual installation kit required.
UNDERCOUNTER
subzero.com/specs
|
57
BUILT-IN
WINE STORAGE
Overall Dimensions
COLUMN
TALL
W
W
24" (610)
PRO 48
4 1/2" (114)
4 1/2" (114)
69 1/2"
84"*
(2134)
24" (610)
44 7/8"
84"*
(1765)
(2134)
(1140)
3/8" (10)
13 5/16"
(338)
3/8" (10)
INTEGRATED
10 9/16"
(268)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
A
A
13/4" (45)
WINE
13/4" (45)
17 3/4"
B
UNDERCOUNTER
IW-18
IW-24
IW-30
B
(451)
COLUMN
MODEL
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
TALL
W
A
B
MODEL
W
A
B
18" (457)
24" (610)
30" (762)
2 1/2" (64)
4" (102)
5 5/8" (143)
16 1/2" (419)
22 1/2" (572)
28 1/2" (724)
IW-30R
30" (762)
5 5/8" (143)
28 1/2" (724)
IMPORTANT NOTE: Overall dimensions do not include panels
or handles. Dimensions will vary with panel thickness.
58
|
Sub-Zero Customer Care 800.222.7820
WINE STORAGE
BUILT-IN
Specifications
INTERIOR CAPACITY
COLUMN
BOTTLES (750 ML)
IW-18
IW-24
IW-30
TALL
IW-30R
59
102
146
R CU FT (L)
BOTTLES (750 ML)
4.0 (113)
86
PRO 48
SHIPPING WEIGHT
COLUMN
IW-18
IW-24
IW-30
TALL
IW-30R
LB (KG)
350 (159)
410 (186)
460 (209)
LB (KG)
490 (222)
INTEGRATED
WINE
UNDERCOUNTER
subzero.com/specs
|
59
BUILT-IN
WINE STORAGE
Opening Dimensions
INTEGRATED WINE STORAGE
OPENING DIMENSIONS
COLUMN AND TALL
18" Column
24" Column
30" Column and Tall
PRO 48
25" (635)
OPENING
DEPTH
TOP VIEW
W
H
18" (457)
24" (610)
30" (762)
84" (2134)
84" (2134)
84" (2134)
The depth of each integrated (IW) model is 24" (610). Allow
for panel thickness when planning the finished opening
depth. A minimum 3 1/2" (89) finished return is required on all
sides of the opening. Framed cabinets will require additional
finished filler material behind the face frame for a proper
installation. Refer to the illustration.
INTEGRATED
DUAL INSTALLATION
H
W
OPENING
HEIGHT
OPENING WIDTH
The unit can be installed next to an integrated refrigeration
model or another integrated wine storage model in a dual
installation. When installing two units side by side, the
opening width is the width of the two units added together.
A dual installation kit will be required for this installation. If a
dual installation kit is not specified, a minimum 2" (51) filler
strip is required between units.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
WINE
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4"
3 1/2" (89)
(19)
TYPICAL
3 1/2" (89)
FINISHED
RETURN
FINISHED
RETURN
W
W
FRAMED CABINETRY
UNDERCOUNTER
FRAMELESS CABINETRY
60
|
FILLER
Sub-Zero Customer Care 800.222.7820
WINE STORAGE
BUILT-IN
Overall Dimensions
Opening Dimensions
MODEL WS-30
MODEL WS-30 STANDARD INSTALLATION
26 3/16" (665)
30" (762)
24" (610)
OPENING
DEPTH
PRO 48
84"
TOP VIEW
(2134)
73 3/4"
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
(2127)
OPENING
HEIGHT
23 7/8" (606)
INTEGRATED
83 3/4"
W
OPENING WIDTH
23 7/8"
(606)
17"
(432)
311/4"
(796)
SIDE VIEW
FRONT VIEW
WINE
NOTE: Shaded line represents profile of unit.
2 3/8" (60)
SPECIFICATIONS
STORAGE CAPACITY
WS-30
SHIPPING WEIGHT
WS-30
OPENING WIDTH
BOTTLES (750 ML)
MODEL
W
147
WS-30
29 1/2" (749)
LB (KG)
445 (202)
If two units are installed side by side, refer to page 63 for
dual standard installations.
subzero.com/specs
|
61
UNDERCOUNTER
Overall dimensions are based on the stainless steel model.
For flush inset applications, add 1/2" (13) to door clearance
dimensions.
If an 83" (2108) grille height is specified, the opening height
must be decreased by 7/8" (22). If an 88" (2235) grille height is
specified, the opening height must be increased by 4" (102).
BUILT-IN
WINE STORAGE
Opening Dimensions
MODEL WS-30 FLUSH INSET INSTALLATION
26 3/16"
2 3/16"
(56)
FINISHED
CLEATS*
PRO 48
(665)
FLUSH
INSET
DEPTH
TOP VIEW
11/4"
INTEGRATED
1/4"
(6)
(32)
W
84"
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
WINE
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
Dimensions assume a 3/4" (19) panel thickness.
FLUSH INSET WIDTH
MODEL
W
WS-30
32" (813)
If an 83" (2108) grille height is specified, the flush inset
height must be decreased by 7/8" (22). If an 88" (2235) grille
height is specified, the flush inset height must be increased
by 4" (102).
UNDERCOUNTER
If two units are installed side by side, refer to page 64 for
dual flush inset installations.
62
|
Sub-Zero Customer Care 800.222.7820
WINE STORAGE
BUILT-IN
Opening Dimensions
MODEL WS-30 DUAL STANDARD INSTALLATION
24" (610)
OPENING
DEPTH
PRO 48
TOP VIEW
(2127)
OPENING
HEIGHT
SIDE VIEW
INTEGRATED
W
83 3/4"
OPENING WIDTH
FRONT VIEW
WINE
NOTE: Shaded line represents profile of unit.
A dual installation kit will be required for this installation.
DUAL OPENING WIDTH
MODELS
WS-30 and 30" Built-In
WS-30 and 36" Built-In
W
59 3/4" (1518)
65 3/4" (1670)
UNDERCOUNTER
subzero.com/specs
|
63
BUILT-IN
WINE STORAGE
Opening Dimensions
MODEL WS-30 DUAL FLUSH INSET INSTALLATION
26 3/16"
2 3/16"
(56)
FINISHED
CLEATS*
PRO 48
(665)
FLUSH
INSET
DEPTH
TOP VIEW
11/4"
INTEGRATED
1/4"
(6)
(32)
W
84"
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
WINE
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
DUAL FLUSH INSET WIDTH
MODELS
UNDERCOUNTER
WS-30 and 30" Built-In
WS-30 and 36" Built-In
64
|
Sub-Zero Customer Care 800.222.7820
W
62 1/4" (1581)
68 1/4" (1734)
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.
WINE STORAGE
BUILT-IN
Electrical
If the unit will be connected to a home security system,
allow 36" (914) of excess wiring for proper connection.
IMPORTANT NOTE: For integrated (IW) models, the electrical
outlet must be positioned with the grounding prong to the
right of the thinner blades.
ELECTRICAL SUPPLY LOCATION
INTEGRATED MODEL
A
18" Model
24" Model
30" Model
6" (152)
9 1/2" (241)
12 1/2" (318)
PRO 48
The electrical supply must be located within the shaded
area shown in the illustration for your specific model. For
integrated (IW) models, also refer to the chart. For model
315W, the electrical supply can be located anywhere on the
back wall of the opening. A separate circuit, servicing only
this appliance is required. A ground fault circuit interrupter
(GFCI) is not recommended and may cause interruption of
operation.
LEFT SIDE
OF OPENING
41/2"
(114)
A
Installation must comply with all applicable electrical codes.
4 1/4"
(108)
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
15 amp
Receptacle
3-prong grounding-type
LEFT SIDE
OF OPENING
7"
INTEGRATED
Service
1/4" (6)
FLOOR
Integrated models.
E
(178)
6"
(152)
2"
(51)
15 1/2"
(394)
3" (76)
Model 424G.
RIGHT SIDE
OF OPENING
WINE
FLOOR
75 1/2" (1918)
FROM FLOOR
Model WS-30.
UNDERCOUNTER
subzero.com/specs
|
65
PRO 48
BUILT-IN
WINE STORAGE
Custom Panels
Custom Panel—315W and 424G
For framed, overlay, integrated and flush inset applications,
a custom door panel must be provided. Handle hardware
must also be provided for overlay, integrated and flush
inset applications. Refer to panel requirements and custom
panel dimensions charts for your specific model and design
application.
For models 315W and 424G, the custom door panel will
attach directly to the door frame with screws through a
series of pre-drilled holes.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory (except model 315W and
WS-30) and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an
authorized Sub-Zero dealer for more information. Overall
dimensions are the same for glass and solid door panels.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
Model 424FSG has a finished stainless steel exterior that is
designed to be used in a freestanding application.
Refer to the charts for panel requirements and dimensions.
PANEL REQUIREMENTS
WEIGHT PER PANEL
MAX
315W
424G
10 lb (5 kg)
10 lb (5 kg)
PANEL THICKNESS
MIN
5/8"
All Panels
(16)
OVERLAY PANEL DIMENSIONS
A
A
A
H
INTEGRATED
A
W
315W, 424G
PANEL DIMENSIONS
MODEL
315W
424G
STILES / RAILS (MIN)
315W
424G
W
H
15" (381)
23 3/4" (603)
30 1/16" (764)
30 1/16" (764)
A
2 1/4" (57)
2 1/4" (57)
WINE
DOOR CLEARANCE
UNDERCOUNTER
Models 315W and 424G can be installed flush with surrounding cabinetry. Depending on the thickness of the
overlay door panel, it may be necessary to install the unit
1/4" (6) beyond the front surface of adjacent cabinetry to
prevent interference when the door is opened to 145°. Refer
to the full-scale template on page 77.
66
|
Sub-Zero Customer Care 800.222.7820
WINE STORAGE
BUILT-IN
Custom Panel—Integrated
For integrated (IW) models, a custom door panel and handle
hardware must be provided. Refer to the panel requirements
chart and typical panel dimensions.
TYPICAL PANEL DIMENSIONS
Do not install a solid panel on the glass door unit. A solid
door is available as a sales accessory through an authorized
Sub-Zero dealer.
79 7/8"
49 3/8"
(2029)
(1254)
PRO 48
The thickness of the custom panel can vary. A minimum
5/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each integrated model is 24" (610). Allow for panel
thickness when planning the finished opening depth. Refer
to the full-scale template on page 53.
CAUTION
13 9/16"
(345)
16 11/16"
(424)
W
As reveals between cabinetry and the unit decrease,
severe finger pinching can occur while door is closing.
D-style handles are recommended. Door handles must be
located near the edge of the panel opposite the hinge and
should be centered top to bottom. Drawer handles must
be located near the top edge of each panel. Stainless steel
tubular and pro handles are avail­able through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com.
Tall
Typical panel dimensions are based on an 84" (2134) finished
height, 4" (102) toe kick and 1/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations.
Refer to the illustration for panel heights and the chart below
for panel widths.
INTEGRATED
Finish all sides of custom panels. They will be visible when
the door/drawer is open.
Column
W
PANEL WIDTH
MODEL
18" Model
24" Model
30" Model
W
17 3/4" (451)
23 3/4" (603)
29 3/4" (756)
PANEL REQUIREMENTS
STILES / RAILS
WEIGHT PER PANEL
Door Frame
Door Frame (IW-30R)
Drawer Panel
PANEL THICKNESS
All Panels
WIDTH
3 1/4" (83)
7 3/4" (197)
9 1/2" (241)
4 1/2" (114)
MAX
35 lb (16 kg)
25 lb (11 kg)
15 lb (7 kg)
MIN
5/8"
DUAL INSTALLATION
For dual installations, refer to the illustration for panel
heights and the chart below for panel widths.
WINE
Stiles
Top Rail
Bottom Rail
Bottom Rail (IW-30R)
PANEL WIDTH
MODEL
18" Model
24" Model
30" Model
W
17 13/16" (452)
23 13/16" (605)
29 13/16" (757)
(16)
UNDERCOUNTER
subzero.com/specs
|
67
BUILT-IN
WINE STORAGE
Custom Panel—Integrated
TOE KICK CLEARANCE
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below. Toe kick heights from
2" (51) to 3 7/8" (98) require a reduced toe kick accessory
available through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.
PRO 48
DOOR PANEL HEIGHT
1 3/4"
(45)
A DECORATIVE VALANCE
CANNOT EXTEND
BEYOND THIS PLANE
1/8" (3)
DOOR
PANEL
84"
24" (610)
(2134)
TO BACK OF UNIT
HINGE**
VENTED
LOUVERS
24" (610)
TO BACK OF UNIT
INTEGRATED
HINGE
DOOR
PANEL
1 1/8" (29)
MAX
TOE KICK
ADJUSTMENT
2" (51)*
TO
6" (152)
FROM
FLOOR
Upper valance (side view).
*2" (51) to 3 7/8" (98) requires sales accessory.
**Column models only.
UNDERCOUNTER
WINE
Toe kick (side view).
68
|
Sub-Zero Customer Care 800.222.7820
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
WINE STORAGE
BUILT-IN
Custom Panel—WS-30
FRAMED PANEL
FRAMED PANEL DIMENSIONS
The framed application is an overlay model with framed
design features. It is not a separate model.
H
A
1/4"
Routing, recessing and optional extended handles may be
required for finger clearance. Refer to the full-scale template
on page 78.
Door
Grille (optional)
PANEL THICKNESS
H
A
MAX
75 lb (34 kg)
13 lb (6 kg)
MIN
1/4"
(6)
WS-30
FRAMED PANEL
PANEL
Door
Grille (optional)
W
H
29 3/4" (756)
29 3/4" (756)
69 9/16" (1767)
8 15/16" (227)
STILES / RAILS
Minimum
A
3 1/8" (79)
INTEGRATED
Framed
A
W
PANEL REQUIREMENTS
WEIGHT PER PANEL
A
PRO 48
(6), a filler material
If the custom panel is thinner than
must be added to achieve a proper fit. If the panel is thicker
than 1/4" (6), rout an edge around the panel or mount the
custom panel on a sheet of 1/4" (6) thick material and insert
into the channel.
WINE
UNDERCOUNTER
subzero.com/specs
|
69
BUILT-IN
WINE STORAGE
Custom Panel—WS-30
OVERLAY PANELS
OVERLAY PANEL DIMENSIONS
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10" (3) spacer panel and a 1/4" (6) backer
panel. Refer to the illustrations below.
PRO 48
PANEL REQUIREMENTS
WEIGHT PER PANEL
MAX
Door
Grille
H
A
A
A
H
75 lb (34 kg)
13 lb (6 kg)
PANEL THICKNESS
MIN
5/8"
Overlay
(16)
A
W
CUSTOM
PANEL
SPACER PANEL
SPACER
PANEL
OVERLAY PANELS
INTEGRATED
CUSTOM PANEL
DOOR
BACKER PANEL
BACKER
PANEL
TRIM
DOOR FRAME
WS-30
GLASS
Overlay Panel
Spacer Panel
Backer Panel
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
STILES / RAILS
5/16" (8) min
1/8"
(3)
A
3 1/4" (83)
Minimum
3/4"
(19)
typical
.10" (3) 1/4" (6)
Panel assembly (cross section). Panel assembly (rear view).
GRILLE
Overlay Panel
Spacer Panel
Backer Panel
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
*Panel height may be increased by 7/16" (11) to hide upper main
frame. For more information, refer to the built-in panel configurator
at subzero.com/trade/panels.
UNDERCOUNTER
WINE
Grille panel dimensions are for standard 84" (2134) overall unit
height. For 83" (2108) height, subtract 1" (25) from grille panel height
dimensions and for 88" (2235) height, add 4" (102). A specific panel
grille must be ordered for an 83" or 88" overall unit height.
70
|
Sub-Zero Customer Care 800.222.7820
WINE STORAGE
BUILT-IN
Custom Panel—WS-30
FLUSH INSET PANELS
FLUSH INSET PANEL DIMENSIONS
The flush inset application is an overlay model with flush
inset panels. It is not a separate model.
For flush inset panels thicker than 3/4" (19), a 90° door stop
may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 81.
PANEL REQUIREMENTS
WEIGHT PER PANEL
Door
Grille
Flush Inset
A
A
H
A
W
WS-30
MAX
75 lb (34 kg)
13 lb (6 kg)
MIN
5/8"
(16)
FLUSH INSET PANELS
DOOR
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
STILES / RAILS
A
3 3/4" (95)
Minimum
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
INTEGRATED
PANEL THICKNESS
A
PRO 48
The flush inset design allows custom panels to be installed
flush with adjacent cabinets. Similar to overlay, flush inset
panels are typically created by combining a 3/4" (19) custom
panel, a .10" (3) spacer panel and a 1/4" (6) backer panel.
Refer to the illustrations for overlay panels on the previous
page.
H
Grille panel dimensions are for standard 84" (2134) overall unit
height. For 83" (2108) height, subtract 1" (25) from grille panel height
dimensions and for 88" (2235) height, add 4" (102). A specific panel
grille must be ordered for an 83" or 88" overall unit height.
WINE
UNDERCOUNTER
subzero.com/specs
|
71
5/16" (8)
WINE STORAGE
BUILT-IN
5/8"
(16)
TOP VIEW
TOP VIEW
CABINETRY
DOOR / DRAWER / GRILLE
1/2" (13)
BACKER
1/8"
5/16" (3)
(8)
CABINETRY
GRILLE
The illustrations provide
offsets and reveals for model
FLUSHpanel
INSET PANEL
WS-30 in a flush inset application.
Refer to the chart below
5/16" (8)
1/2"
for reference to the illustrations.
(13)
5/8"
(16)
PRO 48
PANEL OFFSET
DOOR
DOOR
1/2" (13)
TOP VIEW
DOOR
ILLUS
5/16" (8)
5/8"
(16)
5/16" (8)
1/8" (3)
1/4" (6)
SIDE VIEW
REVEAL
Illus. B
DOOR /
DRAWER
CABINETRY
5/16"
(8) 3/32" GRILLE
(2)
1/2" (13)
5/16"
(8) 5/32"
(4)
DOOR
INTEGRATED
GRILLE
1/2"
(13)
Illus. A
1/8"
5/16" (3)
(8)
5/8" (16)
SIDE VIEW
1/2" (13)
3/32"
5/16" (2)
(8)
1/8"
5SIDE
/16" (3)
VIEW
(8)
5/32" DOOR
5/16" (4)
(8)
SIDE VIEWGRILLE
5/16"
(8)
1/2" (13)
CABINETRY
DRAWER
Illus. C
5/16"
(8) 5/32"
(4)
5/16"
GRILLE
(8) 3/32
"
(2)
DOOR
SIDE VIEW
Illus.
D
DRAWER
SIDE VIEW
WINE
DOOR
1
/16" (3)
(8)
/8"
SIDE
5 VIEW
FLUSH INSET PANEL
A
B
C
D
GRILLE
DOOR
CABINETRY
1/4" (6)
REVEAL
Door / Grille Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
3/32" 1/2" (13)
5/16" (2)
(8)
5/16" (8)
1/8" (3)
BACKER
TOP VIEW
CABINETRY
DOOR / DRAWER / GRILLE
SIDE SPACER
VIEW
FLUSH INSET
5/16"
(8) 5/32"
(4)
GRILLE
Custom Panel—WS-30
SPACER
FLUSH INSET PANEL
OFFSET
1/2"
(13)
3/32"
(2)
5/8" (16)
1/2
DOOR
3/32"
5/16" (2)
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
DOOR /
DRAWER
5/16"
(8) 3/32"
(2)
DOOR
5/8" (16)
DRAWER
5/32"
5/16" (4)
(8)
5/16"
(8)
5/16"
(8) 3/32"
(2)
DOOR
SIDE VIEW
UNDERCOUNTER
DOOR /
DRAWER
SIDE VIEW
DRAWER
3/32"
5/8"(2)
(16)
5/16"
(8)
5/32"
5/16" (4)
(8)
3
SIDE VIEW
72
|
Sub-Zero Customer Care 800.222.7820
SIDE VIEW
WINE STORAGE
BUILT-IN
Custom Panel—WS-30
DUAL FLUSH INSET PANEL DIMENSIONS
DUAL INSTALLATIONS
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the chart on page
70. Panel dimensions and offsets for dual flush inset installations are listed on the following pages.
H
A
A
A
H
PRO 48
If two models WS-30 or a model WS-30 and built-in unit are
installed side by side, a dual installation kit may be required.
Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51)
filler strip is recommended between units. Dual installations
without a filler strip can only be accomplished using two
units with opposite hinges. Refer to the illustrations below.
A
W
WS-30
MODEL WS-30
DOOR
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
STILES / RAILS
A
3 3/4" (95)
Minimum
GRILLE
Flush Inset Panel
Spacer Panel
Backer Panel
WITHOUT FILLER STRIP
H
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
Grille panel dimensions are for standard 84" (2134) overall unit
height. For 83" (2108) height, subtract 1" (25) from grille panel height
dimensions and for 88" (2235) height, add 4" (102). A specific panel
grille must be ordered for an 83" or 88" overall unit height.
WINE
Opposite hinges.
FILLER STRIP
W
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
INTEGRATED
Flush Inset Panel
Spacer Panel
Backer Panel
Same side hinges.
UNDERCOUNTER
subzero.com/specs
|
73
WINE STORAGE
TOP VIEW
TOP VIEW
BUILT-IN
DOOR / DRAWER / GRILLE
BACKER
SPACER
DOOR
CABINETRY
TOP VIEW
5/16" (8)
Custom Panel—WS-30
5/8"
1/2"
(13)
DUAL FLUSH INSET PANEL OFFSET
(16)
1/8" (3)
BACKER
SPACER
BACKER
CABINETRY
SPACER
CABINETRY
PANEL OFFSET
ILLUS
A
B
C
D
E
1/2" (13)
TOP VIEWREVEAL
BACKER
1/8"
5/16" (3)
(8)
INTEGRATED
TOP VIEW
CABINETRY
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1
/8" (3)
DOOR
1/4" (6)
1/4" (6)
REVEAL
REVEAL
FLUSH INSET PANEL
5/16" (8)
5/8"
(16)
GRILLE
CABINETRY
GRILLE
1/2"
(13)
5/8"
(16)
1/8"
5/16" (3)GRILLE
(8)
CABINETRY
1/2"
(13)
5/16" (8)
5/16" (8)
1/8" (3)
1/8" (3)
1/4" (6)
1/4" (6)
REVEAL
REVEAL
5/16"
(8) 5/32"
(4)
Illus. B
1/2" (13)
CABINETRY
1/2" (13)
DOOR
SIDE VIEW
DOOR
DUAL
TRIM
5/16" (8)
1/2"
(13)
DOOR
DOOR
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
Illus. A
GRILLE
DOOR
1/4" (6)
5/8"
SPACER
(16)
Door (hinge) / Grille Sides
Door (handle) Sides
Grille Top
Grille Bottom / Door TopCABINETRY
Door Bottom
TOP VIEW
DOOR / DRAWER / GRILLE
5/16" (8)
The illustrations provide panel offsets and reveals for
model
FLUSH
INSET PANEL
WS-30 in a dual flush inset application. Refer to the chart5
/16" (8)
below for reference to the illustrations.
DUAL FLUSH INSET
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
PRO 48
DOOR
1
3/32" /2" (13)
5/16" (2)
(8)
1/8"
5/16VIEW
SIDE
" (3)
(8)
1/2" (13)
GRILLE
SIDE VIEW
5/16"
(8) 5/32"
(4)
1/2" (13)
DOOR
1/2
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
DOOR
3/32
GRILLE
"
5/16" (2)
(8)
1/8"
5/16
" (3)
SIDE
VIEW
(8)
Illus. C
DOOR /
DRAWER
5/16"
(8) 5/32GRILLE
"
(4)
GRILLE
SIDE VIEW
SIDE VIEW
1/2
DOOR
Illus. D
3/32"
5/16" (2)
(8)
SIDE VIEW
SIDE VIEW
5/16"
(8) 3/32"
(2)
DOOR
WINE
5/8" (16)
DRAWER
5/32"
5/16" (4)
(8)
5/16"
(8)
5/16"
(8) 3/32"
(2)
DOOR
DRAWER
5/DRAWER
Illus.
32E
"
5/16" (4)
(8) DOOR
SIDE VIEW
UNDERCOUNTER
DOOR /
DRAWER
DOOR
5/8" (16)SIDE VIEW
SIDE VIEW
DOOR /
DRAWER
5/16"
(8) 3/32"
(2)
DRAWER
3/32"
5(2)
/8" (16)
5/16"
DOOR /
(8) DRAWER
5/16"
(8)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
SIDE VIEW
3/32"
(2)
3
SIDE VIEW
5/16"
(8)
5/32"
5/16" (4)
(8)
3
SIDE VIEW
74
|
Sub-Zero Customer Care 800.222.7820
SIDE VIEW
WINE STORAGE
BUILT-IN
Custom Panel—WS-30
Standard Handles
SIDE PANEL
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
The custom side panel must be a minimum of 24" (610) deep
and 1/2" (13) thick. Routing will be necessary for the side
panel to fit flush against the side of the unit. Refer to the
illustrations below.
HANDLE LENGTH
WINE STORAGE
315W, 424G Door
IW-18, IW-24, IW-30 Door
IW-30R Door
IW-30R Drawer
WS-30 Door
TUBULAR
PRO
24 1/4" (616)
50 1/8" (1273)
33 1/4" (845)
24 1/4" (616)
63 7/8" (1622)
22 1/4" (572)
48 3/8" (1229)
31 1/2" (800)
22 1/2" (572)
45 3/16" (1147)
PRO 48
When installing model WS-30 with a custom side panel, an
accessory kit is required. Stainless steel and white enamel
side panels are available through an authorized Sub-Zero
dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.
Refer to the chart below for standard handle lengths for
wine storage models.
24" (610)
FRONT
OF SIDE
PANEL
1" (25)
1 7/8" (48)
1 7/8"(48)
1" (25)
INTEGRATED
1/8" (3)
1/2" (13)
ROUT TO 1/8" (3)
84"
MAIN
FRAME
SIDE PANEL
ROUTING
(2134)
Routing detail.
WINE
4" (102)
OPTIONAL
TOE KICK
CUT-OUT
2 5/8"
(67)
Side panel dimensions.
UNDERCOUNTER
subzero.com/specs
|
75
BUILT-IN
WINE STORAGE
Wine Rack Wood Facing
WOOD FACING WIDTH
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for profile dimensions of the wood facing
and the chart for width.
MODEL
PRO 48
FULL-SCALE TEMPLATE
1/2"
5/8"
(13)
(16)
7/64" (3)
7/64" (3)
1/4"
(6)
11/2"
(38)
INTEGRATED
11/16"
27/32"
(27)
5/64" (2)
(21)
23/64"
23/64"
(9)
(9)
9/16"
9/16"
(14)
(14)
IW-18, IW-24,
IW-30, IW-30R
315W, 424G,
424FSG, WS-30
UNDERCOUNTER
WINE
Wine rack wood facing profile.
76
|
Sub-Zero Customer Care 800.222.7820
5/64" (2)
315W
424G, 424FSG
IW-18
IW-24
IW-30, IW-30R
WS-30
WIDTH
10 15/16" (278)
19 1/2" (495)
11 5/8" (295)
17 5/8" (448)
23 5/8" (600)
24 9/16" (624)
WINE STORAGE
BUILT-IN
Door Clearance—315W and 424G
FULL-SCALE TEMPLATE
To allow for a 145° door opening, the unit should extend
a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however,
there is potential for interference with the panel if the
door is opened past 90°.
PRO 48
UNDERCOUNTER
UNIT
ADJACENT
CABINETRY
INTEGRATED
DOOR CLOSED
1/2"
(13)
3/4" (19) DOOR PANEL
1/4" (6)
1/8" (3)
WINE
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
0"
1" (25)
UNDERCOUNTER
SCALE
145° door opening (top view).
subzero.com/specs
|
77
BUILT-IN
WINE STORAGE
Framed Panel—WS-30
PRO 48
FULL-SCALE TEMPLATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
INTEGRATED
STANDARD
FULL-LENGTH HANDLE
2"
1"
(51)
(25)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
1/2" (13) PANEL
WINE
1/4" (6) FRAMED PANEL
DOOR
UNDERCOUNTER
Framed panel thickness.
78
|
Sub-Zero Customer Care 800.222.7820
WINE STORAGE
BUILT-IN
Overlay and Flush Inset Panels—WS-30
FULL-SCALE TEMPLATE
Overlay and flush inset panels must be a minimum of 5/8"
(16) thick to support mounting the handle. Panel thickness
does not include backer and spacer panel. Mount handle
close to the opening edge of the door.
PRO 48
DEPTH OF TUBULAR
AND PRO HANDLES
2"
(51)
3"
INTEGRATED
1"
(25)
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
.10" (3) SPACER PANEL
1/4" (6) BACKER PANEL
WINE
DOOR
Overlay and flush inset panel thickness.
UNDERCOUNTER
subzero.com/specs
|
79
BUILT-IN
WINE STORAGE
Overlay Application—WS-30
FULL-SCALE TEMPLATE
237/8" (606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
PRO 48
0" (0)
1/4" (6)
1/2" (13)
3/4" (19)
1" (25)
11/4" (32)
11/2" (38)
13/4" (44)
INTEGRATED
2" (51)
21/4" (57)
21/2" (63)
23/4" (70)
3" (76)
31/4" (83)
31/2" (89)
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
OVERLAY PANEL
(TYPICAL)
1/4" (6) BACKER
UNDERCOUNTER
PANEL
0"
1" (25)
SCALE
90° door opening (top view).
80
|
Sub-Zero Customer Care 800.222.7820
WINE STORAGE
BUILT-IN
Flush Inset Application—WS-30
FULL-SCALE TEMPLATE
24" (610)
TO BACK WALL
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
1 1/4" (32)
PRO 48
2 3/16" (56)
ASSUMES
3/4" (19)
FLUSH INSET
PANEL
THICKNESS
INTEGRATED
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1/4" (6) BACKER
PANEL
0"
1" (25)
UNDERCOUNTER
SCALE
110° door opening (top view).
subzero.com/specs
|
81
BUILT-IN
WINE STORAGE
PRO 48
FILLER STRIP
11/4" (32)
DOOR
CLOSED
WINE
INTEGRATED
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
Dual Standard Installation—WS-30
FULL-SCALE TEMPLATE
Typical framed, overlay or stainless steel dual installation
with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
UNDERCOUNTER
0"
1" (25)
SCALE
Dual standard installation (top view).
82
|
Sub-Zero Customer Care 800.222.7820
DOOR
OPEN 110°
WINE STORAGE
BUILT-IN
FILLER STRIP
PRO 48
1 1/2" (38)
1/2" (13)
PROFILE OF 3/4" (19) FLUSH INSET PANEL
AND TUBULAR HANDLE
DOOR
CLOSED
INTEGRATED
WINE
Dual Flush Inset Installation—WS-30
DOOR
OPEN 110°
FULL-SCALE TEMPLATE
Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
0"
1" (25)
UNDERCOUNTER
SCALE
Dual flush inset installation (top view).
subzero.com/specs
|
83
UNDERCOUNTER REFRIGERATION
BUILT-IN
Undercounter Refrigeration
KEY FEATURES
•Overlay and stainless steel design applications.
•Handle options coordinate with handles of Wolf cooking
products.
•Models UC-24RO and UC-15I(P)O are UL approved for
outdoor use.
•Energy efficient; many models are ENERGY STAR®
qualified.
PRO 48
Sub-Zero undercounter refrigeration is a helpful addition to a
master suite, bar, home office or media room. In the kitchen,
a high-volume ice machine is a must for entertaining. The
design flexibility of these compact yet roomy units makes
them all the more welcome in any room or outdoor kitchen.
They are ready to be fitted with a custom cabinet panel or
can be ordered with a stainless steel panel.
•Star-K certified (except ice machine models).
UNDERCOUNTER MODELS
UC-24BG
UC-24C(I)
UC-24RO
UC-15I(P)
UC-15I(P)O
INTEGRATED
UC-24R
WINE
UNDERCOUNTER
subzero.com/specs
|
85
BUILT-IN
UNDERCOUNTER REFRIGERATION
Overall Dimensions
UNDERCOUNTER
ICE MACHINE
23 7/8" (606)
14 3/4" (375)
24" (610)
23" (584)
33 5/8"
PRO 48
34"
(854)
(864)
4" (102)
INTEGRATED
4" (102)
18"
(457)
25 3/8"
(645)
6"
(152)
26" (660)
8"
(203)
WINE
SPECIFICATIONS
SPECIFICATIONS
INTERIOR CAPACITY
R CU FT (L)
UC-24R, UC-24RO
UC-24BG
UC-24C(I)
5.7 (161)
6.0 (170)
3.6 (102)
SHIPPING WEIGHT
24" Model
UNDERCOUNTER
Refer to page 91 for door clearance information.
86
|
Sub-Zero Customer Care 800.222.7820
F CU FT (L)
1.1 (31)
STORAGE CAPACITY
LB (KG)
UC-15I(P), UC-15I(P)O
26 (12)
SHIPPING WEIGHT
LB (KG)
Ice Machine
100 (45)
LB (KG)
130 (59)
Model UC-15I overall dimensions do not include panel or
handle.
UNDERCOUNTER REFRIGERATION
BUILT-IN
Opening Dimensions
DUAL INSTALLATION
UNDERCOUNTER
24" (610)
OPENING
DEPTH
TOP VIEW
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
34 1/2"
W
(876)
OPENING
HEIGHT
OPENING WIDTH
INTEGRATED
SIDE VIEW
PRO 48
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between units.
Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the
illustrations below.
FRONT VIEW
OPENING WIDTH
MODEL
24" Model
Ice Machine
W
24" (610)
15 1/4" (387)
Opposite hinges.
DUAL OPENING WIDTH
MODELS
Two 24" Models
WITHOUT FILLER STRIP
FILLER STRIP
Same side hinges.
W
48 1/8" (1222)
WINE
Dual installation kit required.
UNDERCOUNTER
subzero.com/specs
|
87
BUILT-IN
UNDERCOUNTER REFRIGERATION
Electrical
PRO 48
The electrical supply should be located within the shaded
area shown in the illustration. For ice machine models, it is
recommended that electrical supply be placed in an adjacent cabinet. A separate circuit, servicing only this appliance is required.
IMPORTANT NOTE: For outdoor models UC-24RO and
UC-15I(P)O, a ground fault circuit interrupter (GFCI) is
required to reduce the risk of electrical shock. A GFCI is not
recommended for use with other undercounter models and
may cause interruption of operation.
Installation must comply with all applicable electrical codes.
INTEGRATED
LEFT SIDE
OF OPENING
2"
(51)
15 1/2"
(394)
3" (76)
FLOOR
UNDERCOUNTER
WINE
Electrical supply location.
88
|
Sub-Zero Customer Care 800.222.7820
ELECTRICAL REQUIREMENTS
Electrical Supply
Service
Receptacle
115 VAC, 60 Hz
15 amp
3-prong grounding-type
UNDERCOUNTER REFRIGERATION
BUILT-IN
Plumbing
IMPORTANT NOTE: A reverse osmosis system can be used
provided there is constant water pressure as indicated in the
chart below at all times. A copper line is not recommended
for this application.
ICE MACHINE DRAIN
Ice machine models can be ordered with or without a drain
pump. Models without a pump will drain water by gravity.
A drain must be installed.
The drain and inlet water tubes must be plumbed before
connecting to the ice machine. For the gravity drain, horizontal drain lines must have a 1/4" (6) per 12" (305) fall. An air
gap will likely be required between the unit and drain.
A stand pipe with a trap below is acceptable for the drain.
PRO 48
The water supply line should be located within the shaded
area shown in the illustrations below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve between the supply and the
unit. Do not use self‑piercing valves. A saddle valve kit is
avail­able through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com.
PLUMBING REQUIREMENTS
1/4"
OD copper, braided
stainless steel or PEX tubing
Water Supply
Pressure (UC-24CI)
20–100 psi (1.4–6.9 bar)
Pressure (UC-15I)
20–80 psi (1.4–5.5 bar)
INTEGRATED
Excess Line for Connection
36" (914)
LEFT SIDE
OF OPENING
8"
1/2"
(13)
2"
(51)
(203)
24" (610)
ROUGH
OPENING
DEPTH
LOCATION OF
WATER LINE
15 1/2"
(394)
3" (76)
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
WINE
Model UC-24CI.
TOP VIEW
Ice machine.
15 1/4" min (387)
ROUGH
OPENING WIDTH
341/2" (876)
POSITION OUTLET
WITH GROUNDING
PRONG ON RIGHT
LOCATE
ELECTRICAL
WITHIN
SHADED AREA
UNDERCOUNTER
ROUGH
OPENING
HEIGHT
33 5/8" (854)
MINIMUM
HEIGHT
REQUIRED
4" (102)
FRONT VIEW
subzero.com/specs
|
89
BUILT-IN
UNDERCOUNTER REFRIGERATION
Custom Panel
For overlay undercounter models, custom door panels and
handle hardware must be provided. Refer to the charts for
panel requirements and dimensions.
PRO 48
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
WEIGHT PER PANEL
MAX
UC-24R, UC-24C(I)
UC-24BG
UC-15I(P)
20 lb (9 kg)
10 lb (5 kg)
15 lb (7 kg)
PANEL THICKNESS
UNDERCOUNTER
WINE
INTEGRATED
All Panels
90
|
Sub-Zero Customer Care 800.222.7820
MIN
5/8"
(16)
MODEL UC-24BG
For model UC-24BG, the custom door panel will attach
directly to the door frame with screws through a series of
pre-drilled holes. Refer to the illustration below.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory and must be installed if a
solid panel is being specified. Service may be required to
install the door. Contact an authorized Sub-Zero dealer for
more information. Overall dimensions are the same for glass
and solid door panels.
UNDERCOUNTER REFRIGERATION
BUILT-IN
Custom Panel
Standard Handles
OVERLAY PANEL DIMENSIONS
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
A
H
A
A
H
Refer to the chart below for standard handle lengths for
undercounter models.
A
UC-24R, UC-24C(I),
UC-15I(P)
W
HANDLE LENGTH
UC-24BG
UNDERCOUNTER
Door
Outdoor Door
PANEL DIMENSIONS
MODEL
24" Model
Ice Machine
STILES / RAILS (MIN)
UC-24BG
W
H
23 3/4" (603)
15" (381)
30 1/16" (764)
30 3/8" (772)
TUBULAR
PRO
24 1/4" (616)
NA
22 1/2" (572)
15 11/16" (399)
PRO 48
W
A
2 1/4" (57)
INTEGRATED
DOOR CLEARANCE
Undercounter models can be installed flush with surrounding cabinetry. Depending on the thickness of the custom
door panel, it may be necessary to install the unit 1/4" (6)
beyond the front surface of adjacent cabinetry to prevent
interference when the door is opened to 145°. Refer to the
full-scale template on page 93.
WINE
UNDERCOUNTER
subzero.com/specs
|
91
BUILT-IN
UNDERCOUNTER REFRIGERATION
Wine Rack Wood Facing
FULL-SCALE TEMPLATE
WOOD FACING WIDTH
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for profile dimensions of the wood facing
and the chart for widths.
MODEL
WIDTH
19 1/2" (495)
PRO 48
UC-24BG, UC-24C(I)
1/2"
5/8"
(13)
(16)
7/64" (3)
7/64" (3)
1/4"
(6)
11/2"
(38)
INTEGRATED
11/16"
27/32"
(27)
5/64" (2)
(21)
23/64"
23/64"
(9)
(9)
9/16"
9/16"
(14)
(14)
IW-18, IW-24,
IW-30, IW-30R
5/64" (2)
315W, 424G,
424FSG, WS-30
UNDERCOUNTER
WINE
Wine rack wood facing profile.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service
marks of Sub-Zero, Inc. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
92
|
Sub-Zero Customer Care 800.222.7820
UNDERCOUNTER REFRIGERATION
BUILT-IN
Door Clearance—Undercounter
FULL-SCALE TEMPLATE
To allow for a 145° door opening, the unit should extend
a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however,
there is potential for interference with the panel if the
door is opened past 90°.
PRO 48
UNDERCOUNTER
UNIT
ADJACENT
CABINETRY
INTEGRATED
DOOR CLOSED
1/2"
(13)
3/4" (19) DOOR PANEL
1/4" (6)
1/8" (3)
WINE
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
0"
1" (25)
UNDERCOUNTER
SCALE
145° door opening (top view).
subzero.com/specs
|
93
Sub-Zero Residential Limited Warranty
FOR RESIDENTIAL USE
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will
be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless
otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY
For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts
that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all
connecting tubing. If the owner uses Sub-Zero factory certified service, the service provider will repair or
replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or
replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certified service
or other sources.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fifty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at [email protected] or call 800-222-7820.
*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
*Replacement water filters and air purification cartridges are not covered by the product warranty.
Sub-Zero Outdoor Limited Warranty*
FOR RESIDENTIAL USE
FULL ONE YEAR WARRANTY**
For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor
to repair or replace, under normal residential use, any part of the product that proves to be defective in
materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed
by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided
during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless
otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fifty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at [email protected] or call 800-222-7820.
*Product must be approved for outdoor use, designated by model and serial number.
**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
**Replacement water filters are not covered by the product warranty.
SUB-ZERO, INC.
P.O. BOX 44848
MADISON, WI 53744
SUBZERO.COM
800.222.7820
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement