thunderdome-bubble-h..

thunderdome-bubble-h..
To Purchase This Item, Visit BMI Gaming | www.bmigaming.com | (800) 746-2255 | +1.561.391.7200
Assembly Instructions
Thank you for purchasing a Shelti product. All of us at Shelti want you to be completely satisfied with
your Thunderdome Dome Hockey game, so feel free to contact us for help with the assembly of your
product, Shelti parts, or other information you may require.
Tools Required:
14mm Wrench or Socket (Included)
12mm Wrench or Socket (Included)
4mm Hex Wrench (Included)
Phillips Head Screw Driver
Level
Step #1 - Remove Parts from Box
Remove the pedestal from its box. Locate and remove the leg levelers and bolt package.
Contents
Part Number
Dome Hockey Cabinet
Split Pedestal
Accessory Package
Assembly Instructions
Accessory Package Contents
TD-DPA-0
TD-PDA-1
TD-ASA-0
210-0144-0
Leg Levelers
Cabinet Bolt - Hex Head M8x55mm (1 Extra)
Cabinet Washer - M8 (1 Extra)
Hex Wrench - 4 mm
Electronic Scoring Unit
Flat Head Screw - Phillips Head M5x12mm
9/16 Washer - M6 (Not needed)
Nut - M5
Rounded Head Screw - Phillips Head M3x14mm
Washer - M5
Dome Hockey Puck (1” Dia.)
Pedestal Bolt
Pedestal Washer
Pedestal Nut
Thunderdome Side Label
K4
© Copyright 2004, Shelti Inc., Bay City • Michigan
201-0074-0
301-0043-0
303-0025-0
205-0057-0
210-0145-0
301-0044-0
303-0026-0
302-0016-0
301-0045-0
303-0027-0
210-0131-0
301-0058-0
303-0030-0
302-0022-0
217-0002-0
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Quantity
1
1
1
1
4
11
11
1
1
2
2
2
1
1
3
8
16
8
2
To Purchase This Item, Visit BMI Gaming | www.bmigaming.com | (800) 746-2255 | +1.561.391.7200
Step #2 - Assemble the Pedestal
Step #7 - Level the Playfield
Bolt both pedestal halves
together with a bolt,
two washers and a nut
for each of the eight holes as
shown. Lay the pedestal on
its side and have someone
hold the bolt from the
opposite side while you
over tighten the nut.
Using the provided Hex wrench, remove the two bolts on the
corners of the dome on the handle side. Lift the dome to access
the inside by pulling up on the handle. Do not allow the dome
to swing all the way open without supporting it. Place a level
across, lengthwise, and diagonally into the four corners. Raise
and lower the appropriate leg leveler.
Step #8 - Attach the Electronic Scoring Unit
Locate the four wires coming out of the hole located
on the hinge side of the
dome. Plug them into the
scoring unit as shown. Note
that two wires look identical. Switch locations if you
score and it credits the opposing team.
Step #3 - Attach the Leg Levelers
Attach all four leg levelers into the bottom of
the assembled pedestal.
Screw them in clockwise
all the way, but do not
tighten them.
Step #4 - Hook up the Power Cords
Thread the AC adapter cord (black arrow below)
through the bottom of the pedestal (fig. A) and
through the hole drilled into the wooden speaker
bracket (fig. B). Carefully place the top half of the
game on to the pedestal. Have someone hold it at an
angle so you can access the inside. Take the power
cord and plug it in to the hole located on the underside of the playfield cabinet (fig. C).
Bolt the scoring unit to the edge of the
dome using the (2) nuts and bolts provided. Slip the bolt through the bottom
of the dome and scoring unit and tighten
with the bolt and a phillips head screwdriver. Be careful not to pinch the wires
for the scoring unit in the dome when lifting it. Attach the
final screw and washer through the front of the unit. Slip the
screw through the small hole in the dome from the inside and
tighten.
Step #9 - Operating the Scoring Unit
A
B
C
Take the wire that is taped to the bottom of the
playfield cabinet and plug it in to the hole located
by the speaker (shown above with the white arrow).
Step #5 - Attach Cabinet
Carefully move the top
half of the game on to
the pedestal. Note that
the end with the handles
lines up with the side
of the pedestal with (2)
bolt holes. Using (10) hex
head bolts and washers,
secure both halves together.
Step #6 - Attach Optional Stickers
Attach one sticker on each side of the cabinet as
shown above. Peeling away half of the back at a time
makes it a little easier to locate the center.
Turn the power switch
to “on”. Select desired
game option. By default, it begins with the
15 minute game option.
To change the game
option, push the “select” button. There are seven total options
including “Free play” which has no time limit or scoring limit.
After choosing a game option, push the “Start” button to begin. To start over, press the” Reset / Start” button again. The
volume switch has three settings: High, Low and Off.
Step #10 - Ejecting Puck Into Play
Push the green button located at either playing position to
eject the puck. Do not put more than one puck in the game at
a time as the puck ejection mechanism will jam. Push the Red
button to play a sound effect.
333 Morton Street
Bay City, Michigan 48706
Phone: 989-893-1739
Fax: 989-893-1809
www.shelti.com
[email protected]
Member of:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement