PROGRAMMING Each transmitter has its own code number (selected from more than... from all other remote controls. The receiver can receive all the...

PROGRAMMING Each transmitter has its own code number (selected from more than... from all other remote controls. The receiver can receive all the...
PROGRAMMING
Each transmitter has its own code number (selected from more than 250 million) that distinguishes it
from all other remote controls. The receiver can receive all the codes but is activated only if that
particular code is on the list of “authorised” codes. A code number can be entered or deleted from
this list by means of a “learning” procedure.
The operator has to press a button on the receiver card to activate the procedure: the operations
are timed so first read all the instructions and then carry out the operations one after the other
without stopping.
A small red LED visually indicates the different steps of the procedure.
This LED is the only way to check the various operations or receiver states. Because there is a lot of
information to display, there are 2 stable states plus a series of flashes with two speeds:
• LED off: normal functioning mode
• LED on: learning procedure in progress
FAST FLASHING 1/4 second
SLOW FLASHING 1/2 second
No. flashes
1
DESCRIPTION
The code number received is not
among those authorised.
2*
End of learning time without any
result.
3
Learning
successfully
(authorised code number).
4
The code number is already on the
authorised code list.
5
The
6
The list is full (there is no room for
other code numbers).
7
A request has been made to delete a
code number that does not exist.
8
Different code numbers were
received during the learning phase.
9
Password entered.
list
is
empty
(no
finished
No. flashes
1
2
3
When it turns on it means there is a
BM1000 memory card; it then
indicates that the code is not in the
code number window but that it has
been re-synchronised.
4
When it turns on it means there are
code numbers memorised that do not
belong to the Flor version; it then
indicates that the code number is not
in the code number window and resynchronisation is stopped.
5
When it turns on it means that an
error was found in the memory during
reading; it then indicates that the code
is not in the code number window and
re-synchronisation is impossible.
codes) .
* If the 2nd type of disabling function is active, the 2nd flash will be longer than the first
If the 2nd type of disabling function is not active, both flashes will be the same
DESCRIPTION
When it turns on it means there is a
BM60 memory card; it then indicates
that the code number received is a
“copy” while only “original” codes are
valid.
When it turns on it means there is a
BM250 memory card.
Fig. 10
LED
PUSH BUTTON
LED
PUSH BUTTON
PUSH BUTTON
LED
Entering a code number (fast way)
This is the quickest way to enter a code number although it is not very safe because while the code
number is being memorised the receiver could receive a signal from another transmitter that is within
its range and memorise it.
You must take this risk into consideration when
Fig. 8
deciding how to enter your code number.
MEMORIES
LED
LED
MEMORIE
CH.1
CH.1
This operation will also let you add the code number
of a new transmitter to the receiver’s memory.
CH.1
CH.1
PUSH PULSANTE
BUTTON
3 4 5 6 7 8
1) Press the key on the receiver and hold it down:
the LED turns on and you must then:
2) Transmit the code number until the LED turns off
pressing any key on the transmitter.
3) Now release the transmitter key:
the LED will turn back on ready for a new operation.
4) Repeat the procedure from point 2 for the other
transmitters.
GB
Entering a code number (normal way)
This operation too will let you add the code number of a new transmitter to the receiver’s memory.
1) Press the key on the receiver for a moment: the LED will turn on for 5 seconds. Within this time
you must:
2) Transmit the code number until the LED turns off pressing any key on the transmitter.
3) Release the transmitter key and wait a second.
4) Transmit the code to confirm by pressing any key on the transmitter.
The LED will now flash 3 times meaning that the operation was done properly; if this does not
happen, repeat the whole procedure from the beginning. Repeat the whole procedure if you want to
enter a new code number.
Entering a code number (remotely)
To enter the code number of a new remote control without using the receiver key you will need an
authorised remote control (note: the first remote control must always be entered using the receiver
key). Now, with the two remote controls, which we shall call NEW (the one whose code number we
want to enter) and OLD (the authorised one), position yourself in their range of action and then:
1) Transmit the NEW code number for at least 5 seconds pressing any key on the NEW
transmitter.
And then slowly:
2) Transmit an OLD code number 3 times pressing any key on the OLD transmitter 3 times.
3) Transmit the NEW code number ONCE to confirm pressing any key on the NEW transmitter.
Now the new code number has been entered and you can repeat this procedure immediately with
another remote control.
ATTENTION!! : this operation enters the new code number in all the receivers within the range
of action that recognise the old code number. If there are several receivers nearby with the
old code number, turn the ones off that you do not want to receive the new code number.
DELETING A CODE NUMBER
If you want to delete a code number from the receiver’s memory proceed as follows:
1)
2)
3)
4)
Hold the key down on the receiver (about 3 seconds) when the LED turns off let go of the key.
Transmit the code until the LEDs turn off again pressing any key on the transmitter.
Release the key on the transmitter and wait 1 second.
Transmit the code to confirm pressing any key on the transmitter.
The LED will now flash once to indicate that the code has been deleted. If this does not
happen repeat the procedure from the beginning.
GB
DELETING ALL CODE NUMBERS
With this operation all the code numbers stored are deleted (emptying the memory), the 2nd learning
disabling function is also cancelled and TIMER time is set at 3 seconds.
1)
2)
3)
4)
Hold the key down on the receiver, the LED will turn off after 3 seconds.
Release the key during the 3rd following flash.
Wait about 3 seconds.
Press the key as soon as the LED turns back on and release it as soon as it turns off.
The operation may take several seconds depending on memory type. During this phase the LED will
flash quickly followed by 5 slow flashes to indicate that it has been reset and the memory is empty;
if this does not happen repeat the procedure from the beginning.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement