Canon | DR-2050SP | User`s guide | Canon DR-2050SP User`s guide

Document Scanner DR-2050C/SP
3.
❏ Before installing the software, make sure your computer is correctly running one of
the following versions of Windows. For details, refer to the DR-2050C/DR-2050SP
User’s Guide.
• Windows 98SE
• Windows Me
• Windows 2000 Professional SP4 or later
• Windows XP Home Edition SP2 or later
• Windows XP Professional SP2 or later
❏ Do not connect the scanner to the computer before installing the software. If you
connect the scanner and turn it ON before you install the software, a wizard screen
will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn
the scanner OFF.
Checking the Accessories
Feed Roller
USB Cable
Type A/Type B
AC Adapter/Power Cord
(Length: 6 ft. (1.8 m)) (Connected length: 8 ft. 6 in. (2.6 m))
Click [Finish] to complete the installation.
Next, the installation wizard for
CapturePerfect 3.0 appears.
8.
Click [Next].
9.
Read the software license agreement, and
click [Yes] if you consent to the conditions of
the software.
Warning
Thank you for purchasing the Canon DR-2050C/DR-2050SP Document Scanner. This Easy
Start Guide describes the procedure for setting up the scanner for use. Follow the
procedures outlined in this Easy Start Guide to set up the scanner. Details on using the
scanner are described in the User’s Guides packaged with the scanner. Before you use the
scanner, make sure to thoroughly read the User’s Guides.
DR-2050C/DR-2050SP
7.
Install the software before connecting the scanner to the computer.
Easy Start Guide
When you unpack your scanner, make sure that it contains all of the following accessories. If
any of the items listed below are missing or damaged, contact your local authorized Canon
dealer or service representative.
Installing the Software
1) and (2
2), and remove the orange tape fastening the
Open the front cover at (1
roller cover.
4.
5.
Open the roller cover.
1), and slide it towards the left (2
2).
Lower the roller lock lever (1
Wizard Screen (Windows 2000)
Easy Start Guide
(this document)
Document
Guide Adapter
DR-2050C/DR-2050SP
User’s Guide
6.
0880281099-L5T1P7-BR01
CANON CANADA INC.
6390 DIXIE RD
MISSISSAUGA
ON
L5T
DR-2050C
Setup Disc
Adobe Acrobat
Setup Disc
❏ Be sure to log on with administrator privileges when logging on to Windows.
❏ Close all other applications before installing the software.
Adjustment Sheet
9Z9
Load the feed roller, align the notch on the roller with the shaft on the scanner
body.
Registration Card
Warranty Card
(U.S.A. and Canada only) (U.S.A. and Canada only)
1.
2.
*For the DR-2050SP, the following accessories are included in addition to the above items.
DR-2050SP User’s Guide
Presentation Mode Edition
Remote Control
AAA Batteries (2)
RGB Cable
Mini D-sub 15 Pin × 2
(Length: 5 ft. (1.5 m))
7.
Slide the roller lock lever towards the right, fit the lever feed roller into the hole on
1), and push down the roller lock lever to lock the feed roller
the left of the roller (1
2).
shaft (2
3.
Note
●
●
●
●
●
●
To use the feed roller, install it on the scanner.
☞ [STEP 2] “Removing the Packing Materials and Installing the Feed Roller”
Documents can be prevented from feeding slantwise by installing the document
guide adapters on the document guides. (☞ STEP 5)
The adjustment sheet is used to adjust the scanner when anomalies begin to
appear in scanned images. Store it in a safe place where it will not be lost.
The DR-2050 Setup Disc contains the “DR-2050C Scanner Driver”,
“CapturePerfect 3.0”, and “OmniPage SE” made by Nuance Communications Inc.
☞ DR-2050C/DR-2050SP User’s Guide p.17 “About the Setup Disc”
Items included in this package are subject to change without notice.
You must keep the machine’s packaging and packing materials for storing or
transporting the machine.
After checking the package contents, you need to prepare the scanner
for use. (☞ STEP 2)
10. Check the destination folder and click [Next].
Turn ON your computer.
Insert the DR-2050C Setup Disc into the
PC’s CD-ROM drive.
The setup wizard automatically starts up
when you insert the CD-ROM into the CDROM drive. If the setup wizard does not
start up, execute setup.exe in the CD-ROM.
Click [Typical Installation].
If you click [Typical Installation], all of the
software is installed. If you want to select
which parts of the software to install, click
[Custom Installation].
Installation of CapturePerfect 3.0 starts.
11. Click [Finish] to complete the installation of
CapturePerfect 3.0.
12. Next, installation of OmniPage SE starts.
Follow the messages on the screen to
proceed with the installation.
8.
Close the roller cover. Make sure that the roller cover clicks into place.
4.
Click [Install].
All of the currently displayed software is
installed. To install only selected software,
click [Back] and select [Custom
Installation].
13. When all installations are complete, the
9.
Gently push in the front unit on its left and right sides to close the front unit.
Make sure that the front unit clicks into place.
5.
Click [Next].
14. Remove the setup disc, and finish the
Installation completed screen appears.
Click [Exit] to exit the installer.
(Click [Back] to return to the menu screen.)
software installation.
Removing the Packing Materials and
Installing the Feed Roller
Remove the scanner from the box, remove the orange tape and protective sheets from the
scanner, and install the feed roller on the scanner body.
1.
2.
10. Close the document feed tray and top cover.
Document Feed Tray
Top Cover
Peel off the four pieces of orange tape from the outer casing.
The scanner is now ready for use.
Next, you need to install the scanner software. (☞ STEP 3)
■ Trademarks
• Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be
trademarks or registered trademarks in other countries.
• Microsoft Windows® is a registered trademark of Microsoft USA in the United States and other countries.
• Other brands and product names used in this manual may be trademarks or registered trademarks of their
respective companies.
©2007 CANON ELECTRONICS INC.
Read the software license agreement, and
click [Yes] if you consent to the conditions of
the software.
Installation of the scanner driver starts.
Note
●
When software is installed the icons are added to the Program menu.
During scanner driver installation, the
scanner driver and the Job Registration
Tool are installed.
Open the document feed tray and remove the protective sheet.
PUB. CE-IE-546
6.
(Windows 2000)
This completes the software installation.
Next, you need to connect the scanner to your computer. (☞ STEP 4)
☞ Continued on back side
☞ Continued from front side
Connecting and Registering the
Scanner to Your PC
2.
2).
Plug the AC adapter into the connector located to the left of the connector (2
3.
3).
Plug the power cord into the power outlet (3
4).
Connect the USB cable to the scanner and your PC (4
5.
Check the scanner and computer connections, and press the power button to
5).
turn the scanner ON (5
DR-2050C
DR-2050SP
Warning
3.
1.
Load a document in the scanner according to steps 1 to 5 of [STEP 5].
2.
Press the scan button on the scanner, or point the remote control at the infrared
receiver on the scanner and press the FORWARD key.
Scanning starts with the following settings.
Scan settings: Color, 150 dpi, simplex (default values)
When the first page of the document is finished scanning, it is projected. Up to
40 pages can be scanned continuously with simplex scanning.
Open the document feed tray.
Thoroughly fan the pages of your documents, and shift the pages so that the top
edge of the first page is the bottommost page. (Place your documents on the
scanner so that the top edge is facing down.)
ABC
4.
Perform the following steps to load and scan a document and confirm that it is projected
properly.
Note
Presentation mode can be tested by connecting the DR-2050SP to a PC monitor.
If your projector is in a distant location, such as a conference room, connect the
DR-2050 to a PC monitor to check the operation of presentation mode.
ABC
1).
Connect the power cord to the AC adapter (1
1.
2.
4
1.
Perform the following steps to connect the DR-2050SP to an LCD projector (or PC monitor)
with the supplied RGB cable (mini D-sub 15 pin).
❏ Always use the supplied RGB cable. The quality of projected images cannot be
guaranteed for other RGB cables.
123
❏ Use only the AC adapter included in the package.
❏ Connect the DR-2050C to your computer while the DR-2050C is turned OFF.
❏ Be sure to log on with administrator privileges when logging on to Windows.
When you have finished installing the software and the scanner has been recognized, you
can load and scan a document.
With this scanner, scanning can be performed with the job function by simply pressing the
scan button. Follow the steps below to load a document, press the scan button, and test that
your document is scanned properly.
4
Warning
Testing Presentation Mode
(For the DR-2050SP only)
123
Perform the following steps to connect the scanner, turn it on, and register it to your PC.
Preparing Presentation Mode
Scanning
Place your documents so that top edge is facing down and the rear side is facing
towards you. Adjust the document guide adapter to fit the size of the documents.
1.
Disconnect the USB cable connecting the scanner to the PC.
Presentation mode cannot be initiated while the scanner and PC are connected.
Make sure to disconnect the USB cable connecting the scanner to the PC.
2.
Connect the scanner to the LCD projector (or monitor) with the supplied RGB
cable.
Infrared
Transmitter
PC
(USB Port)
FORWARD Key
Infrared Receiver
Scan Button
Type B
Type A
Type B
If documents feed slantwise during scanning, attach the document guide
adapters to the document guides on both sides of the scanner.
t. 5
6 f ))
1
to m
Up (5
(
Warning
To move the document guides while the
document guide adapters are attached, always
grasp the document guides. Grasping the ends
of the document guide adapters may cause
them to break.
4.
6.
Windows recognizes the DR-2050C/SP as the “DR-2050C”, and installation is
performed automatically.
Make sure that the feed selection lever on the side is set to the page separation
mode ( ).
Be careful, because when the feed selection lever is set to (bypass mode),
document pages feed as a stack. For details on the feed selection lever, refer to
the DR-2050C/DR-2050SP User’s Guide.
Infrared Receiver
(Rear)
Mini D-sub 15 Pin
To RGB Output Connector
Mini D-sub 15 Pin
To RGB Input Connector
3.
3.
Insert the two supplied AAA batteries into the remote control.
Align the + and – battery terminals as indicated.
Use the remote control to check the scanned image.
Use the buttons below to check the displayed image. For details on the
functions of other buttons and menu operations, refer to the DR-2050SP User’s
Guide Presentation Mode Edition.
Turn the remote control over, and detach the
battery cover.
Returns to the previous image
Zooms the image in
Bypass Mode
(Windows 98/Me/2000)
Rotates the image to the left
Page Separation
Mode
Insert the two batteries, aligning the + and –
signs on the remote control with those on the
batteries.
Feed Selection Lever
(Windows XP)
5.
in.
Press the Scan button.
“Monitor for DR-2050C” is displayed at the bottom right of the screen and
scanning starts.
Scan settings: Black & White, 300 dpi, simplex (default values)
Displays the next image
Zooms the image out
Rotates the image to the right
Displays the menu toolbar
Switches to thumbnail display
Reattach the battery cover.
Adjusts the brightness
Note
●
For Windows XP, a balloon help pop-up appears when installation is finished.
4.
The installation finished message is not displayed in Windows 98/Me/2000.
● When the DR-2050C/SP is recognized by the PC, it is registered as “CANON DR2050C USB” in the “Imaging Device” directory of the Device Manager.
Scan Button
●
6.
When “Sending complete” is displayed on the “Monitor for DR-2050C”, this
indicates that scanning has ended. Click “Close” to close the “Monitor for
DR-2050C”.
5.
Turn on the LCD projector (or monitor).
When connected to an LCD projector, turn on the projector and wait until it
warms up and starts projecting.
Note
Turn on the scanner.
When the scanner is turned on, the startup screen appears and initialization
starts. Wait until the projector is warmed up and projecting before turning on
the scanner.
●
●
●
●
●
The scan settings “Color, 150 dpi” are basic specifications for presentation mode,
and cannot be changed.
A maximum of 40 pages of scanned images can be stored in the scanner’s
memory.
When scanning is started with no images stored in the scanner’s memory,
scanning stops when 40 pages have been scanned with simplex scanning (or 20
pages have been scanned with duplex scanning).
When scanning is started with images already stored in the scanner’s memory,
scanning stops when a total of 40 pages have been scanned.
When scanning is started with 40 images already stored in the scanner’s memory,
only one page is scanned, and the oldest image stored in memory is deleted.
Note
The function of the job button can be changed.
☞ DR-2050C/DR-2050SP User’s Guide p.34 “Using the Job Function”
● Scanned image files are saved in the [My Pictures] folder in [My Documents].
(Default)
● Image files that are saved according to the default settings are saved as PDF files
with a 17-digit file name. This file name indicates the date and time that the image
was saved.
● You can change the scan settings by using the Job Registration Tool.
●
To open the Device Manager screen, open “System” on the Control Panel and
click [Device Manager] on the “Hardware” tab.
● If the OS is Windows XP, “System” is displayed when the display is switched to the
classic view display on the Control Panel.
●
The scanner is now correctly recognized by your computer.
In the last step, you can test that documents are scanned properly.
(☞ STEP 5)
The startup screen is usually displayed for about 20 seconds to 2 minutes. Do
not operate the scanner while the startup screen is displayed, because the
scanner’s internal settings are being initialized.
6.
When the startup screen exits, a message appears.
The setup is now complete
This completes setup of the DR-2050C. Details on how to use the DR-2050C are
described in the separate DR-2050C/DR-2050SP User’s Guide. Before you start
using the DR-2050C, be sure to thoroughly read the DR-2050C/DR-2050SP User’s
Guide.
● When using the DR-2050SP, continue to the next section to test the operation of
presentation mode.
● Details on presentation mode are described in the separate DR-2050SP User’s
Guide Presentation Mode Edition. Before you start using presentation mode, be sure
to thoroughly read the DR-2050SP User’s Guide Presentation Mode Edition.
● For details on how to use CapturePerfect 3.0, refer to the “CapturePerfect 3.0
Operation Guide” or the online Help included on the CD-ROM.
●
This completes the preparation of presentation mode.
Now you need to scan a document and test that it is projected
properly. (☞ STEP 7)
The setup of the DR-2050SP is now complete
This completes setup of the DR-2050SP. Details on how to use the DR-2050SP are
described in the separate DR-2050C/DR-2050SP User’s Guide. Before you start
using the DR-2050SP, be sure to thoroughly read the DR-2050C/DR-2050SP User’s
Guide.
● Details on presentation mode are described in the separate DR-2050SP User’s
Guide Presentation Mode Edition. Before you start using presentation mode, be sure
to thoroughly read the DR-2050SP User’s Guide Presentation Mode Edition.
●
Download PDF

advertising