VTech CS6124-21 User`s manual

VTech CS6124-21 User`s manual
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
CS6120-2
CS6120-31
CS6124
CS6124-2
CS6124-31
DECT 6.0 cordless telephone
BC
User’s manual
Congratulations
on purchasing your new VTech product.
Before using this telephone, please read
Important safety instructions.
This manual has all the feature
operations and troubleshooting
necessary to install and operate your
new VTech telephone. Please review
this manual thoroughly to ensure
proper installation and operation of
this innovative and feature rich VTech
product.
For support, shopping, and everything
new at VTech, visit our website at
www.vtechphones.com. In Canada,
please visit www.vtechcanada.com.
Compatible with
Hearing Aid T-Coil
T
TIA-1083
Telephones identified with
this logo have reduced
noise and interference
when used with most T-coil
equipped hearing aids
and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of the
Telecommunications Industry
Association. Used under
license.
The ENERGY STAR® program
(www.energystar.gov)
recognizes and encourages
the use of products that save
energy and help protect our
environment. We are proud
to mark this product with
the ENERGY STAR® label
indicating it meets the latest
energy efficiency guidelines.
Important safety
instructions
When using your telephone equipment,
basic safety precautions should always
be followed to reduce the risk of fire,
electric shock and injury, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Unplug this product from the wall
outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water
such as near a bath tub, wash
bowl, kitchen sink, laundry tub or a
swimming pool, or in a wet basement
or shower.
5. Do not place this product on an
unstable table, shelf, stand or other
unstable surfaces.
6. Slots and openings in the back or
bottom of the telephone base and
handset are provided for ventilation.
To protect them from overheating,
these openings must not be blocked
by placing the product on a soft
surface such as a bed, sofa or rug.
This product should never be placed
near or over a radiator or heat
register. This product should not be
placed in any area where proper
ventilation is not provided.
7. This product should be operated
only from the type of power source
indicated on the marking label. If you
are not sure of the type of power
supply in your home or office, consult
your dealer or local power company.
8. Do not allow anything to rest on
the power cord. Do not install this
product where the cord may be
walked on.
9. Never push objects of any kind into
this product through the slots in the
telephone base or handset because
they may touch dangerous voltage
points or create a short circuit. Never
spill liquid of any kind on the product.
10. To reduce the risk of electric shock,
do not disassemble this product,
but take it to an authorized service
facility. Opening or removing parts of
the telephone base or handset other
than specified access doors may
expose you to dangerous voltages or
other risks. Incorrect reassembling
can cause electric shock when the
product is subsequently used.
11. Do not overload wall outlets and
extension cords.
12. Unplug this product from the wall
outlet and refer servicing to an
authorized service facility under the
following conditions:
! When the power supply cord or
plug is damaged or frayed.
! If liquid has been spilled onto the
product.
! If the product has been exposed to
rain or water.
! If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operation instructions. Improper
adjustment of other controls
may result in damage and often
requires extensive work by an
authorized technician to restore
the product to normal operation.
! If the product has been dropped
and the telephone base and/or
handset has been damaged.
! If the product exhibits a distinct
change in performance.
13. Avoid using a telephone (other than
cordless) during an electrical storm.
There is a remote risk of electric
shock from lightning.
14. Do not use the telephone to report
a gas leak in the vicinity of the leak.
Under certain circumstances, a spark
may be created when the adapter
is plugged into the power outlet,
or when the handset is replaced in
its cradle. This is a common event
associated with the closing of any
electrical circuit. The user should
not plug the phone into a power
outlet, and should not put a charged
handset into the cradle, if the
phone is located in an environment
containing concentrations of
flammable or flame-supporting
gases, unless there is adequate
ventilation. A spark in such an
environment could create a fire
or explosion. Such environments
might include: medical use of
oxygen without adequate ventilation;
industrial gases (cleaning solvents;
gasoline vapors; etc.); a leak of
natural gas; etc.
15. Only put the handset of your
telephone next to your ear when it is
in normal talk mode.
16. The power adapter is intended to be
correctly oriented in a vertical or floor
mount position. The prongs are not
designed to hold the plug in place if
it is plugged into a ceiling, under-thetable or cabinet outlet.
SAVE THESE INSTRUCTIONS
Battery
! CAUTION: Use Only Supplied Battery.
! Do not dispose of the battery in a fire.
Check with local waste management
codes for special disposal instructions.
! Do not open or mutilate the battery.
Released electrolyte is corrosive and
may cause burns or injury to the eyes
or skin. The electrolyte may be toxic if
swallowed.
! Exercise care in handling batteries in
order not to create a short circuit with
conductive materials.
! Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in
this manual.
!
Precautions for users of implanted
cardiac pacemakers
Cardiac pacemakers (applies only to
digital cordless telephones):
Wireless Technology Research, LLC
(WTR), an independent research entity,
led a multidisciplinary evaluation of the
interference between portable wireless
telephones and implanted cardiac
pacemakers. Supported by the U.S.
Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
! Should keep wireless telephones at
least six inches from the pacemaker.
! Should NOT place wireless telephones
directly over the pacemaker, such as
in a breast pocket, when it is turned
ON.
! Should use the wireless telephone at
the ear opposite the pacemaker.
!
!
WTR’s evaluation did not identify any
risk to bystanders with pacemakers from
other persons using wireless telephones.
About cordless telephones
! Privacy: The same features that
make a cordless telephone convenient
create some limitations. Telephone
calls are transmitted between the
telephone base and the cordless
handset by radio waves, so there is a
possibility that the cordless telephone
conversations could be intercepted
!
by radio receiving equipment within
range of the cordless handset. For
this reason, you should not think of
cordless telephone conversations as
being as private as those on corded
telephones.
Electrical power: The telephone
base of this cordless telephone must
be connected to a working electrical
outlet. The electrical outlet should not
be controlled by a wall switch. Calls
cannot be made from the cordless
handset if the telephone base is
unplugged, switched off or if the
electrical power is interrupted.
Potential TV interference: Some
cordless telephones operate
at frequencies that may cause
interference to televisions and
VCRs. To minimize or prevent
such interference, do not place
the telephone base of the cordless
telephone near or on top of a TV or
VCR. If interference is experienced,
moving the cordless telephone farther
away from the TV or VCR often
reduces or eliminates the interference.
Rechargeable batteries: Exercise
care in handling batteries in order
not to create a short circuit with
conducting material such as rings,
bracelets and keys. The battery or
conductor may overheat and cause
harm. Observe proper polarity
between the battery and the battery
charger.
Nickel-metal hydride rechargeable
batteries: Dispose of these batteries
in a safe manner. Do not burn or
puncture the battery. Like other
batteries of this type, if burned or
punctured, they could release caustic
material which could cause injury.
Directory ................................................... 12
Add a directory entry ................................. 12
Review a directory entry............................ 12
Alphabetical search ................................... 13
Delete a directory entry ............................. 13
Edit a directory entry ................................. 13
Dial a directory entry ................................. 13
Table of contents
What’s in the box ....................................... 1
Overview..................................................... 2
Telephone base overview ........................... 2
Handset overview........................................ 2
Charger overview ........................................ 3
Display icons overview ................................ 3
Telephone base lights overview .................. 3
Caller ID .................................................... 14
Review a caller ID log entry ...................... 14
Memory match........................................... 14
Missed call indicator .................................. 14
View dialing options................................... 15
Dial a caller ID log entry ............................ 15
Save a caller ID log entry to
the directory .......................................... 15
Delete the caller ID log entries .................. 16
Connect ...................................................... 4
Connect the telephone base ....................... 4
Connect the charger.................................... 4
Mount the telephone base........................... 4
Install and charge the battery ...................... 4
Before use .................................................. 6
Set date and time ........................................ 6
Check for dial tone ...................................... 6
Operating range .......................................... 6
Sound settings......................................... 16
Key tone .................................................... 16
Ringer tone ................................................ 16
Telephone base ringer volume .................. 16
Handset ringer volume .............................. 17
Temporary ringer silencing ........................ 17
!"#$%&'()!%&(*'+',-!"' ......................... 7
Use the handset menu ................................ 7
Set language ............................................... 7
Set date and time ........................................ 7
Home area code .......................................... 7
Dial mode .................................................... 8
Temporary tone dialing ................................ 8
About the built-in answering system
and voicemail service ......................... 17
Set your built-in answering system ....... 18
Turn the answering system on or off ......... 18
Default announcement .............................. 19
Record your own announcement .............. 19
Play the announcement ............................ 19
Delete the announcement ......................... 19
Set number of rings ................................... 20
Set recording time ..................................... 20
Turn the call screening on or off ................ 20
Turn the message alert tone on or off ....... 20
Telephone operations ............................... 9
Make a call .................................................. 9
Predial a call ................................................ 9
Answer a call ............................................... 9
End a call:.................................................... 9
Volume ........................................................ 9
Mute ............................................................ 9
Join a call in progress (for multiple
handset models only) ........................... 10
Call waiting ................................................ 10
Chain dialing.............................................. 10
Find handset...............................................11
Use your built-in answering system ...... 21
New message indication ........................... 21
Message playback .................................... 21
Delete all messages .................................. 22
Remote access ......................................... 22
Set your remote access code ................... 23
Call screening............................................ 23
Call intercept ............................................. 23
Record, play or delete memos .................. 24
Redial list.................................................. 11
Review a redial list entry ............................11
Dial a redial list entry ..................................11
Delete a redial list entry ..............................11
i
Use the built-in answering system
and voicemail service ......................... 24
Retrieve voicemail from telephone
service.................................................. 25
Retrieve voicemail ..................................... 25
Turn off the new voicemail indicators ........ 25
Register a handset .................................. 25
Other information .................................... 26
Website ..................................................... 26
Screen messages .................................... 26
General product care .............................. 28
Frequently asked questions ................... 28
The RBRC® seal ....................................... 31
FCC, ACTA and IC regulations ............... 32
California Energy Commission
battery charging testing
instructions ......................................... 34
For C-UL compliance only ...................... 35
Limited warranty ...................................... 38
.'/-"0/1+(2,'/0#/1*0!"2 ......................... 40
ii
What’s in the box
Your telephone package contains the
following items. Save your sales receipt
and original packaging in the event
warranty service is necessary.
NOTE
1 set for CS6120-2/CS6124-2;
2 sets for CS6120-31/CS6124-31
! To purchase a replacement battery or
power adapter, visit our website at
www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call
1 (800) 267-7377.
Abridged
user’s
manual
Important
safety
instructions
1 set for CS6120-2/CS6120-31/
CS6124/CS6124-2/CS6124-31
1 set for CS6120-2/CS6120-31/
CS6124/CS6124-2/CS6124-31
1 set for CS6124;
2 sets for CS6120-2/CS6124-2;
3 sets for CS6120-31/CS6124-31
1
! On when the telephone is in use, or
the answering system is answering a
call.
Overview
Telephone base overview
Handset overview
1 – /REPEAT
! Repeat a message.
! Press twice to play the previous
message.
2 – /SKIP
! Skip to the next message.
3 – /FIND HANDSET
! Page all system handsets.
4 – Charging pole
5 – Speakerphone
6 – X/DELETE
! Delete the playing message.
! Press twice to delete all old
messages.
7 – Message window
8 – /PLAY/STOP
! Play messages.
! Stop playing messages.
9 – /!/VOLUME
! Adjust the listening volume.
! Adjust the telephone base ringer
volume.
10 – /ANS ON/OFF
! Turn on or off the answering system.
11 – IN USE light
! Flashes when there is an incoming
call, or another telephone sharing the
same line is in use.
1 – Handset earpiece
2 – LCD display
3 – CID/VOL! Review the caller ID log when the
telephone is not in use.
! Scroll down while in a menu, or in the
directory, caller ID log or redial list.
! Move the cursor to the left when
entering numbers or names.
! Decrease the listening volume during
a call or message playback.
4 – /FLASH
! Make or answer a call.
! Answer an incoming call when you
receive a call waiting alert.
5–1
! Press repeatedly to add or remove 1
in front of the caller ID log entry before
dialing or saving it to the directory.
6 – TONE
! Switch to tone dialing temporarily
during a call.
7 – MUTE/DELETE
! Mute the microphone during a call.
2
! Silence the handset ringer temporarily
while the phone is ringing.
! Delete the displayed entry while
reviewing the directory, caller ID log or
redial list.
! Delete digits or characters when
entering numbers or names.
8 – Microphone
9 – Charging pole
10 – MENU/SELECT
! Show the menu.
! While in a menu, press to select an
item, or save an entry or setting.
11 –
/VOL+
! Review the directory when the phone
is not in use.
! Scroll up while in a menu, or in the
directory, caller ID log or redial list.
! Move the cursor to the right when
entering numbers or names.
! Increase the listening volume during a
call or message playback.
12 – OFF/CANCEL
! Hang up a call.
! Return to the previous menu or idle
mode without making changes.
! Delete digits while predialing.
! Silence the handset ringer temporarily
while the phone is ringing.
! Erase the missed call indicator while
the handset is not in use.
13 – 0/OPER
! Enter space character during text
editing.
14 – #
! Show other dialing options when
reviewing a caller ID log entry.
15 – REDIAL/PAUSE
! Review the redial list.
! Insert a dialing pause while dialing or
entering numbers into the directory.
16 – Battery compartment cover
Charger overview
1 – Charging pole
Display icons overview
The battery icon flashes
when the battery is low and
needs charging.
The battery icon animates
when the battery is charging.
The battery icon becomes
solid when the battery is fully
charged.
There are new messages on
the built-in answering system.
There are new voicemail
received from your telephone
service provider.
NEW
There are new caller ID log
entries.
ANS ON
The answering system is
turned on.
1
The message number
currently playing.
Telephone base lights overview
IN USE
! On when the telephone line
is in use.
! On when the answering
system is answering a call.
! Flashes quickly when there
is an incoming call.
! Flashes when another
telephone sharing the
same line is in use.
/ANS ON/ On when the answering
system is turned on.
OFF
3
Mount the telephone base
Connect
You can choose to connect the
telephone base for desktop usage or wall
mounting.
NOTES
! Use only the adapters provided.
! Make sure the electrical outlets are not
controlled by wall switches.
! The adapters are intended to be correctly
oriented in a vertical or floor mount
position. The prongs are not designed to
hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
Install and charge the battery
TIP
Install the battery
! If you subscribe to digital subscriber line
(DSL) high-speed Internet service through
your telephone line, make sure you install
a 345(#+*'& (not included) between the
telephone line cord and telephone wall
jack. Contact your DSL service provider for
more information.
Install the battery as shown below.
NOTES
! Use only supplied battery.
! Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in this
manual.
! If the handset will not be used for a long
time, disconnect and remove the battery to
prevent possible leakage.
Connect the telephone base
THIS SIDE UP
Connect the charger
4
Charge the battery
Place the handset in the telephone
base or the charger to charge.
Battery
indicators
Battery
status
The screen
is blank, or
displays Put
in charger
and flashes.
The battery
has no or
very little
charge. The
handset
cannot be
used.
Charge
without
interruption
(at least 30
minutes).
The screen
displays
Low battery
and flashes.
The battery
has enough
charge to
be used for
a short time.
Charge
without
interruption
(about 30
minutes).
The screen
displays
HANDSET X.
The battery
is charged.
To keep
the battery
charged,
place it in the
telephone
base or
charger when
not in use.
Action
When the battery is fully charged, you
can expect the following performance:
Once you have installed the battery,
the handset LCD display indicates the
battery status (see the following table).
Operation
While in use (talking*)
Operating
time
Seven hours
While not in use (standby**) Five days
NOTES
* Operating times vary depending on your
actual use and the age of the battery.
** Handset is not charging nor in use.
! For best performance, keep the handset
in the telephone base or charger when not
in use.
! The battery is fully charged after 16 hours
of continuous charging.
! If you place the handset in the telephone
base or the charger without plugging in the
battery, the screen displays No battery.
5
Before use
Operating range
After you install your telephone or power
returns following a power outage, the
handset will prompt you to set the date
and time.
This cordless telephone operates with
the maximum power allowed by the
Federal Communications Commission
(FCC). Even so, this handset and
telephone base can communicate over
only a certain distance - which can vary
with the locations of the telephone base
and handset, the weather, and the layout
of your home or office.
When the handset is out of range, the
handset displays Out of range or no
pwr at base.
If there is a call while the handset is out
of range, it may not ring, or if it does ring,
the call may not connect well when you
press . Move closer to the telephone
base, then press
to answer the call.
If the handset moves out of range during
a telephone conversation, there may be
interference. To improve reception, move
closer to the telephone base.
Set date and time
NOTE
! Make sure you set the date and time
including the year correctly; otherwise the
answering system does not announce the
correct day of the week for your recorded
messages time stamp.
1. Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then press SELECT.
2. Use the dialing keys (0-9) to enter
the hour (HH) and minute (MM).
Then press ! or
to choose AM or
PM.
3. Press SELECT to save.
Check for dial tone
Press . If you hear a dial tone, the
installation is successful.
If you do not hear a dial tone:
! Make sure the installation procedures
described above are properly done.
! It may be a wiring problem. If you have
changed your telephone service to
digital service from a cable company
or a VoIP service provider, the
telephone line may need to be rewired
to allow all existing telephone jacks to
work. Contact your cable/VoIP service
provider for more information.
6
!"#$%&'()!%&(*'+',-!"'
4. Use the dialing keys (0-9) to enter
the hour (HH) and minute (MM).
Then press ! or
to choose AM or
PM.
5. Press SELECT to save your setting.
Your hear a confirmation tone.
Use the handset menu
1. Press MENU when the phone is not
in use.
2. Press or until the screen displays
the desired feature menu.
3. Press SELECT.
! To return to the previous menu, press
CANCEL.
! To return to idle mode, press and hold
CANCEL.
Home area code
If you dial local calls using only seven
digits (area code not required), you
can program your home area code so
that when you receive a call within your
local area, the telephone number is
automatically stored in the caller ID log
without the area code.
1. Press MENU when the handset is
not in use.
2. Press ! or
to choose Settings
and then press SELECT.
3. Press ! or
to choose Home area
code, and then press SELECT. The
screen displays the currently stored
home area code.
4. Use the dialing keys (0-9) to enter
the desired home area code.
! Press DELETE to delete a digit.
! Press and hold DELETE to delete
all digits.
5. Press SELECT to confirm. You hear
a confirmation tone.
Set language
The LCD language is preset to English.
You can select English, French or
Spanish to be used in all screen
displays.
1. Press MENU when the handset is
not in use.
2. Press ! or
to choose Settings
and then press SELECT twice.
3. Press ! or
to choose English,
Français or Español.
4. Press SELECT twice to save your
setting. You hear a confirmation tone.
Set date and time
NOTE
! Make sure you set the date and time
including the year correctly; otherwise the
answering system does not announce the
correct day of the week for your recorded
messages time stamp.
NOTE
! If, in the future, your telephone service
provider requires you to dial the area code
when making a local call, or, if you move to
a location that requires it, delete the home
area code you have already programmed
following the steps above. After you have
deleted the home area code, ___ appears.
1. Press MENU on the handset when
not in use.
2. Press ! or
to choose Set
date/time and then press SELECT.
3. Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then press SELECT.
7
Dial mode
The dial mode is preset to touch-tone
dialing. If you have pulse (rotary) service,
you need to change the dial mode to
pulse dialing before using the telephone.
1. Press MENU when the handset is
not in use.
2. Press ! or
to choose Settings,
and then press SELECT.
3. Press ! or
to choose Dial mode,
then press SELECT.
4. Press or to choose Touch-tone
or Pulse, then press SELECT to
confirm your selection. You hear a
confirmation tone.
Temporary tone dialing
If you have pulse (rotary) service only,
you can switch from pulse to touch-tone
dialing temporarily during a call. This is
useful if you need to send touch-tone
signals to access your telephone banking
or long distance services.
1. During a call, press TONE .
2. Use the dialing keys to enter the
number. The telephone sends touchtone signals. It automatically returns
to pulse dialing mode after you end
the call.
8
Make a call
Telephone operations
! Press , and then dial the telephone
number.
Handset control key panel:
NOTES
! The screen shows the elapsed time as you
talk (in hours, minutes and seconds).
! If the handset is moved out of range while
on a call, it will beep three times.
Predial a call
! Enter the telephone number using
the dialing keys (0-9), then press
to dial.
NOTE
! When predialing (preview numbers before
dialing), press DELETE or CANCEL to
backspace and delete; press and hold
PAUSE to insert a dialing pause (a P
appears).
Answer a call
! Press
or any of the dialing keys.
End a call:
! Press OFF or put the handset back in
the telephone base or charger.
CANCEL
Volume
! During a call, press VOL- or VOL+ to
adjust the listening volume.
Mute
The mute function allows you to hear the
other party but the other party cannot
hear you.
1. During a call, press MUTE. The
handset displays Muted.
2. Press MUTE again to resume the
conversation. The handset displays
Microphone on briefly.
9
Join a call in progress (for
multiple handset models only)
Chain dialing
Use this feature to initiate a dialing
sequence from numbers stored in the
directory, caller ID log or redial while you
are on a call.
Chain dialing can be useful if you wish
to access other numbers (such as bank
account numbers or access codes) from
the directory, caller ID log or redial list.
You can use three handsets at a time on
an outside call.
! When a handset is already on a call,
press
on another handset to join
the call.
! To exit the call, press OFF on the
handset or place it in the telephone
base or charger. The call continues
until all handsets hang up.
To access a number in the
directory while on a call:
Call waiting
1. Press MENU/SELECT twice to enter
the directory.
2. Press ! or
to scroll to the desired
entry.
3. Press SELECT to dial the displayed
number.
When you subscribe to call waiting
service from your telephone service
provider, you hear an alert tone if there
is an incoming call while you are already
on a call.
! Press FLASH to put the current call on
hold and take the new call.
! Press FLASH at any time to switch
back and forth between calls.
To access a number in the caller
ID log while on a call:
1. Press MENU and then press ! or
to select Caller ID log.
2. Press SELECT and then press ! or
to scroll to the desired entry.
3. Press SELECT to dial the displayed
number.
If you also subscribe to caller ID
service, it will let you see the name and
telephone number of the caller during
call waiting.
It may be necessary to change your
telephone service to use this feature.
Contact your telephone service provide if:
! You have both caller ID and call
waiting, but as separate service (you
may need to combine these service);
! You have only caller ID service, or
only call waiting service; or
! You do not subscribe to caller ID or
call waiting services.
To access a number in the redial
list while on a call:
1. Press REDIAL.
2. Press !,
or REDIAL repeatedly to
browse to the desired entry.
3. Press SELECT to dial the displayed
number.
There are fees for caller ID services. In
addition, services may not be available in
all areas.
10
Redial list
NOTES
! You cannot edit a directory entry while on
a call. Refer to the Directory section for
more details.
! You cannot copy a caller ID log entry into
the directory while on a call. Refer to the
Caller ID log section for more details.
! You cannot erase a redial entry while on
a call. Refer to the Redial list section for
more details.
! Press CANCEL to exit redial, directory or
caller ID log when you are on a call.
Each handset stores the last five
telephone numbers dialed. Entries are
shown in reverse chronological order.
When there are already five entries, the
oldest entry is deleted to make room for
the new entry.
Review a redial list entry
1. Press REDIAL when the handset is
not in use.
2. Press !,
or REDIAL repeatedly
until the desired entry displays.
Find handset
Use this feature to find the system
handset.
Dial a redial list entry
To start paging:
1. Press REDIAL when the handset is
not in use.
2. Press !,
or REDIAL repeatedly
until the desired entry displays.
3. Press
to dial.
! Press /FIND HANDSET on the
telephone base when not in use.
All idle handsets ring and display
** Paging **.
To end paging:
-OR1. Press
when the handset is not in
use.
2. Press REDIAL and then press !,
or REDIAL repeatedly until the
desired entry displays.
3. Press SELECT to dial.
! Press /FIND HANDSET at the
telephone base.
-ORor any of the dialing keys on
! Press
the handset.
NOTES
! Press MUTE to turn off the ringer of
a handset temporarily. Paging tone
continues on the other handset.
! Do not press and hold /FIND HANDSET
for more than four seconds. It may lead
to handset deregistration. If the handset
displays To register HS and See manual,
refer to the Register a handset section to
register the handset back to the telephone
base.
Delete a redial list entry
1. Press REDIAL when the handset is
not in use.
2. Press !,
or REDIAL repeatedly to
browse to the desired entry.
3. Press DELETE to delete the
displayed number. You hear a
confirmation tone.
11
5. Press SELECT to save. The handset
displays Saved and then you hear a
confirmation tone.
Directory
The directory can store up to 30 entries,
which are shared by all handsets. Each
entry may consist of a telephone number
up to 30 digits, and a name up to
15 characters.
Each handset directory is independent
(for multiple handset models only). Any
additions, deletions or edits made on
one handset are not reflected on other
handsets.
If the telephone number in the directory
exceeds 15 digits, a dash appears after
the 14th digit and then the remaining
digits are shown beginning with a dash,
alternately.
While entering names and numbers,
you can:
! Press DELETE to backspace and
erase a digit or character.
! Press and hold DELETE to erase the
entire entry.
! Press ! or
to move the cursor to
the left or right.
! Press and hold PAUSE to insert a
dialing pause (for entering numbers
only).
! Press 0 to add a space (for entering
names only).
Review a directory entry
Add a directory entry
Entries are sorted alphabetically.
1. Press when the phone is not in
use.
2. Press ! or
to browse through the
directory, or use the dialing keys to
start a name search.
-OR1. Press MENU when the handset is
not in use.
2. Press ! or
to scroll to Directory
then press SELECT.
3. Press ! or
to scroll to Review
and then press SELECT.
4. Press ! or
to browse.
1. Enter the number when the phone is
not in use. Press MENU, then go to
Step 3.
-ORPress MENU when the phone is not
in use, then press or to scroll to
Directory. Press SELECT twice to
choose Add contact.
2. When Enter number displays, use
the dialing keys to enter the number.
-ORCopy a number from the redial list by
pressing REDIAL and then press !,
or REDIAL repeatedly to select a
number. Press SELECT to copy the
number.
3. Press SELECT to move on to enter
the name. The handset displays
Enter name.
4. Use the dialing keys to enter the
name. Additional key presses show
other characters of that particular
key. The first character of every word
is capitalized.
12
Alphabetical search
Edit a directory entry
1. Follow the steps in Review a
directory entry above to enter the
directory.
2. Use the dialing keys to enter the
letter associated with the name.
For example, if you have entries for
Jenny, Jessie, Kristen and Laura in
your directory, press 5 (JKL) once
to see Jenny (when Jenny displays,
press ! to see Jessie), twice to see
Kristen, or three times to see Laura.
If there is no name entry matching
your search, the next closest match
in alphabetical order appears. If
necessary, press ! or
to browse.
1. Search for the desired entry in the
directory (see Review a directory
entry or Alphabetical search).
2. When the desired entry appears,
press SELECT. The handset
displays Edit number and the stored
number.
3. Use the dialing keys to edit the
number, then press SELECT. The
handset displays Edit name and
then the stored name.
4. Use the dialing keys to enter the
name. Additional key presses show
other characters of that particular
key. The first character of every word
is capitalized.
5. Press SELECT to save. The handset
displays Saved and then you hear a
confirmation tone.
Delete a directory entry
1. Search for the desired entry in the
directory (see Review a directory
entry or Alphabetical search).
2. When the desired entry appears,
press DELETE. The handset
displays Delete contact? and the
number.
3. Press SELECT to confirm. The
handset displays Deleting ... and
then Contact deleted. You hear a
confirmation tone.
Dial a directory entry
1. Search for the desired entry in the
directory (see Review a directory
entry or Alphabetical search).
2. When the desired entry appears,
to dial.
press
13
Review a caller ID log entry
Caller ID
1. Press CID when the phone is not in
use.
2. Press ! or
to browse through the
caller ID log.
If you subscribe to caller ID service,
information about each caller appears
after the first or second ring. If you
answer a call before the caller
information appears on the screen, it will
not be saved in the caller ID log.
The caller ID log stores up to 30 entries.
Each entry has up to 24 digits for the
phone number and 15 characters for the
name.
If the telephone number has more that
15 digits, only the last 15 digits appear.
If the name has more than 15 characters,
only the first 15 characters are shown
and saved in the caller ID log.
Entries appear in reverse chronological
order. When the caller ID log is full, the
oldest entry is deleted to make room for
new incoming call information.
Caller ID log entries are shared by all
system handsets (for multiple handset
models only). Any deletions made on
one handset are reflected on all other
handsets.
-OR1. Press MENU when the phone is not
in use. Press ! or
to select Caller
ID log.
2. Press SELECT twice and then press
! or
to browse.
NOTE
! You hear two beeps when you reach the
beginning or end of the caller ID log.
Memory match
When the incoming telephone number
matches the last seven digits of a
telephone number in your directory, the
screen displays the stored name of the
directory entry.
For example, if Linda Jones calls, her
name appears as Linda if this is how you
entered it into your directory.
NOTE
! The number shown in the caller ID log
is in the format sent by the telephone
service provider. It usually delivers 10-digit
telephone numbers (area code plus
phone number). If the last seven digits
of the incoming telephone number does
not match a number in your directory, the
name appears as it is delivered by the
telephone service provider.
NOTE
! This product can provide information
only if both you and the caller are in
areas offering caller ID service and if
both telephone service providers use
compatible equipment. The time and
date are sent by your telephone service
provider along with the call information.
Missed call indicator
When there are calls that have not been
reviewed in the caller ID log, the handset
displays XX missed calls.
Each time you review a caller ID log
entry marked NEW, the number of
missed calls decreases by one.
14
When you have reviewed all the missed
calls, the missed call indicator no longer
displays.
If you do not want to review the missed
calls one by one, press and hold
CANCEL on the idle handset to erase
the missed call indicator. All the entries
are then considered old.
Dial a caller ID log entry
When the number is shown in the correct
format for dialing, press
to dial.
Save a caller ID log entry to the
directory
1. When in the caller ID log, press ! or
to browse.
2. When the desired caller ID log
entry displays, press SELECT. The
handset displays Edit number and
the stored number.
3. Use the dialing keys to modify the
number, if necessary. Then press
SELECT. The handset displays Edit
name and then the stored name.
4. Use the dialing keys to modify the
name, if necessary. Then press
SELECT. The handset displays
Saved and then you hear a
confirmation tone.
While entering names and numbers,
you can:
! Press DELETE to backspace and
erase a digit or character.
! Press and hold DELETE to erase the
entire entry.
! Press ! or
to move the cursor to
the left or right.
! Press and hold PAUSE to insert a
dialing pause (for entering numbers
only).
! Press 0 to add a space (for entering
names only).
View dialing options
Although the caller ID log entries
received have 10 digits (the area code
plus the seven-digit number), in some
areas, you may dial only the seven digits,
or a 1 plus the seven digits, or a 1 plus
the area code plus the seven digits. You
can change the number of digits that you
dial from or store to the directory.
While reviewing the caller ID log, press #
(pound key) repeatedly to show different
dialing options for local and long distance
numbers before dialing or saving the
telephone number in the directory.
Press 1 repeatedly if you need to add
or remove 1 in front of the telephone
number before dialing or saving it in the
directory.
Mike Smith
800-595-9511
10:15
Press #
Press #
Press #
Press #
-ORPress 1
Press 1
PM
12/25
1-800-595-9511
595-9511
1-595-9511
800-595-9511
1-800-595-9511
800-595-9511
NOTE
! If you have programmed the home area
code, only the last seven digits of the
incoming phone numbers from that area
code will be displayed while reviewing the
caller ID log. Press # repeatedly to display
all possible dialing options.
15
Delete the caller ID log entries
Sound settings
1. When in the caller ID log, press ! or
to browse.
2. When the desired caller ID log entry
displays, press DELETE. You hear a
confirmation tone.
Key tone
You can turn the key tone on or off.
1. Press MENU when the handset is
not in use.
2. Press ! or
to choose Settings
and then press SELECT.
3. Press ! or
to choose Key tone,
then press SELECT.
4. Press ! or
to choose On or Off,
then press SELECT to save. You
hear a confirmation tone.
To delete all caller ID log entries:
1. Press MENU when the phone is not
in use.
2. Press ! or
to select Caller ID log
and then press SELECT.
3. Press ! or
to select Del all calls
then press SELECT.
4. The screen displays Delete all?.
Press SELECT to confirm. The
handset displays Deleting... and
then you hear a confirmation tone.
Ringer tone
You can choose from different ringer
tones for each handset.
1. Press MENU when the handset is
not in use.
2. Press ! or
to choose Ringers
and then press SELECT.
3. Press ! or
to choose Ringer
tone, then press SELECT.
4. The screen displays Tone: with the
current setting flashing. Press ! or
to choose a ringer tone. A sample
of each ringer tone plays as you
scroll through the choices.
5. Press SELECT to save. You hear a
confirmation tone.
NOTE
! If you turn off the ringer volume, you will
not hear ringer tone samples.
Telephone base ringer volume
Press /VOLUME or !/VOLUME on
the telephone base to adjust the ringer
volume when the telephone base is not
in use.
When you set the ringer volume to zero,
the base ringer is off. The telephone
base announces, “Base ringer is off.”
16
Handset ringer volume
About the built-in
answering system and
voicemail service
You can adjust the handset ringer
volume level, or turn the ringer off.
1. Press MENU when the handset is
not in use.
2. Press ! or
to choose Ringers
and then press SELECT twice.
3. The screen displays Volume: with
the current setting flashing. Press
! or
to choose a volume level. A
sample of each ringer volume plays
as you scroll through the choices.
4. Press SELECT to save. You hear a
confirmation tone.
For message recording, your telephone
has a built-in answering system, and it
also supports voicemail service offered
by your telephone service provider
(subscription is required, and fee may
apply).
The main differences between them are:
Category
Storage
NOTES
! If the ringer volume is set to Off, the idle
screen displays Ringer off.
! When the ringer volume is set to Off, the
handset still rings when you press /FIND
HANDSET at the telephone base.
Temporary ringer silencing
When the telephone is ringing, you can
temporarily silence the ringer without
disconnecting the call. The next call rings
normally at the preset volume.
To silence the handset ringer:
! Press CANCEL or MUTE. The
handset displays Ringer muted.
Method
to retrieve
messages
To silence the telephone base
ringer:
! Press
/VOLUME once.
17
Built-in
answering
system
Voicemail from
telephone
service
Messages
are stored in
the telephone
base.
Messages
are stored
in a server
or system
provided by
your telephone
service
provider.
Your
messages
will not be
deleted
automatically.
You have to
delete your
messages
manually.
Your
messages
may be
automatically
deleted after a
period of time.
Contact your
telephone
service
provider for
more details.
When you
received new
messages,
the handset
displays
XX new
messages
, and
and
the message
window on
the telephone
base flashes.
When you
received new
messages,
the handset
displays
and New
voicemail.
Method
to retrieve
messages
To retrieve
messages,
usually there
are two
ways:
!Press
on the
telephone
base; or
!Access
remotely
with an
access
code.
Set your built-in answering
system
To retrieve
messages,
you need
an access
number and/
or a passcode
provided by
your telephone
service
provider.
The answering system can record
and store up to 99 messages. Each
message can be up to three minutes in
length. The total storage capacity for the
announcement, messages and memos
is approximately 14 minutes. The actual
recording time depends on individual
message characteristics.
Your answering system allows you to set
your announcement, to save and delete
messages, activate call screening, to set
number of rings before pick up, to access
remotely, and to control the recording
time.
Telephone base control key panel:
Turn the answering system on
or off
The answering system must be turned
on to answer and record messages.
When the answering system is turned
on, the /ANS ON/OFF light on the
telephone base turns on and ANS ON
displays on the handset.
To turn on or off with the telephone
base:
! Press /ANS ON/OFF to turn the
built-in answering system on or
off. When the answering system is
turned on, it announces, “Calls will
be answered.” When the answering
system is turned off, it announces,
“Calls will not be answered.”
18
To turn on or off with the handset:
Play the announcement
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Answer
on/off and then press SELECT.
4. Press ! or
to choose On or Off
and then press SELECT to save.
You hear a confirmation tone.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys then press SELECT.
3. Press SELECT to select
Announcement.
4. The handset displays Play [2] Del [3]
Rec [7] and it announces, “To play,
press 2. To record, press 7.” Press 2
to play the current announcement.
Default announcement
Options during playback:
! Press VOL+ or VOL- to adjust the
listening volume.
! Press 5 or OFF to stop at any time.
The telephone is preset with a greeting
that answers calls with “Hello, please
leave a message after the tone.” You
can use this preset announcement, or
replace it with your own.
Delete the announcement
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys then press SELECT.
3. Press SELECT to select
Announcement.
4. The handset displays Play [2]
Del [3] Rec [7] and it announces,
“To play, press 2. To record, press
7.” Press 3 to delete your own
recorded announcement. The
handset displays Annc deleted
and it announces, “Announcement
deleted.” You hear a confirmation
tone.
Record your own announcement
The announcement can be up to
90 seconds in length.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys then press SELECT.
3. Press SELECT to select
Announcement.
4. The handset displays Play [2] Del
[3] Rec [7] and it announces, “To
play, press 2. To record, press 7.”
Press 7 to record.
5. The handset displays Record
in 5 sec (counting down) and
it announces, “Record after the
tone. Press 5 when you are done.”
After the tone, speak towards the
microphone of the handset.
6. The handset displays Recording...
Stop [5]. Press 5 when finished.
NOTE
! After you deleted your own recorded
announcement, the answering
system answers calls with the default
announcement.
NOTE
! Announcements shorter than two seconds
will not be recorded.
19
Set number of rings
Turn the call screening on or off
You can set the answering system to
answer an incoming call after two, three,
four, five or six rings; or toll saver.
If you choose toll saver, the answering
system answers a call after two rings
when you have new messages, or
after four rings when you have no new
messages. This enables you to check
for new messages and avoid paying
unnecessary long distance charges if
you are calling from outside your local
area.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Ans sys
setup and then press SELECT.
4. Press ! or
to choose # of rings
and then press SELECT.
5. Press ! or
to choose 6, 5, 4,
3, 2 or Toll saver and then press
SELECT to save. You hear a
confirmation tone.
You can hear incoming messages at
the telephone base while they are being
recorded.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Ans sys
setup and then press SELECT.
4. Press SELECT to select Call
screening.
5. Press ! or
to choose On or Off,
and then press SELECT to save.
You hear a confirmation tone.
Turn the message alert tone on
or off
When the message alert tone is set
to on, and there is at least one new
message, the telephone base beeps
every
10 seconds.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Ans sys
setup and then press SELECT.
4. Press ! or
to choose Msg alert
tone, and then press SELECT.
5. Press ! or
to choose On or Off,
and then press SELECT to save.
You hear a confirmation tone.
Set recording time
You can set the recording time for each
incoming message.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Ans sys
setup and then press SELECT.
4. Press ! or
to choose Recording
time and then press SELECT.
5. Press ! or
to choose 3 minutes,
2 minutes or 1 minute, and then
press SELECT to save. You hear a
confirmation tone.
NOTES
! The answering system must be turned on
for the message alert tone to be functional.
! Press any key on the telephone base
(except /FIND HANDSET) to temporarily
silence the message alert tone.
20
Message playback
Use your built-in answering
system
If you have new messages, the
telephone plays only the new messages
(oldest first). If there are no new
messages, the telephone plays back all
messages (oldest first).
When playback begins, you hear the
total number of messages followed
by the date and time of the message.
After the last message, the telephone
announces, “End of messages.”
New message indication
When there are new answering system
messages, the handset displays XX new
messages and , and the message
window on the telephone base flashes.
When you are reviewing a new message,
NEW and
display on the handset.
Message
window
display
0
No messages.
1-99
Total number of old
messages and memos
recorded.
The message number
currently playing.
0-99
(flashing)
NOTE
Description
! Make sure you set the date and time
correctly. Refer to Set date and time
under the !"#$%&'()!%&(*'+',-!"'
section for more details.
To playback messages at the
telephone base:
! Press
when the phone is not in
use. When you have no message in
the answering system, the telephone
base announces, “You have no
message.”
Total number of new
messages recorded, or the
current message number
during new message
playback.
The clock needs to be set.
Options during playback:
! Press /VOLUME or /VOLUME to
adjust the listening volume.
! Press /SKIP to skip to the next
message.
! Press /REPEAT to repeat the playing
message. Press /REPEAT twice to
listen to the previous message.
! Press X/DELETE to delete the
playing message. The telephone base
announces, “Message deleted,” and
then advances to the next message.
! Press /STOP to stop the playback.
1-99 & F The answering system
(alternating) memory is full with total
number of messages
recorded.
1-8
The telephone base speaker
volume level while adjusting.
0-6
The telephone base ringer
level while adjusting.
--
The answering system is
answering a call, or recording
a memo or announcement.
The handset is on a call, or in
the caller ID log.
The answering system is
being accessed remotely.
If the message alert tone is turned on,
the telephone base beeps every 10
seconds when there are messages that
have not been reviewed.
21
To playback messages with a
handset:
To delete all messages with the
telephone base:
1. Press MENU when the telephone
is not in use. The handset displays
Play messages.
2. Press SELECT. When you have
messages, the handset displays
Playing... and then Repeat [4]
Del [3] Skip [6] and it announces
the total number of messages.
When you have no message in the
answering system, the handset
displays No messages and it
announces, “You have no message.”
1. Press X/DELETE when the phone is
not in use. The system announces,
“To delete all old messages, press
DELETE again.”
2. Press X/DELETE immediately.
The system announces, “All old
messages deleted.” If you do not
have old messages, the system
announces, “You have no old
message.”
To delete all messages with a
handset:
Options during playback:
! Press VOL- or VOL+ to adjust the
listening volume.
! Press 6 to skip to the next message.
! Press 4 to repeat the playing
message. Press 4 twice to listen to the
previous message.
! Press 3 to delete the playing
message. The handset announces,
“Message deleted,” and then
advances to the next message.
! Press OFF to stop the playback.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Delete all
old and then press SELECT. The
handset displays Delete all msg?.
If you do not have old messages, the
handset displays No old messages.
4. Press SELECT to confirm. The
handset displays Deleting ... and
then No old messages. You hear a
confirmation tone.
NOTES
! Only one handset or the telephone base
can access the answering system at a
time.
! During message playback, if there is an
incoming call or another handset makes a
call, message playback will be stopped.
Remote access
A two-digit security code is required to
access the answering system remotely
from any touch-tone telephone. The
preset code is 19. You can use this
preset code, or set your own.
1. Dial your telephone number from any
touch-tone telephone.
2. When the system plays your
announcement, enter the two-digit
security code.
Delete all messages
You can only delete old (reviewed)
messages. You cannot delete new
messages until you review them. You
cannot retrieve deleted messages.
22
3. Enter one of the following remote
commands.
Command
Set your remote access code
You can set your own remote access
code from 00 to 99.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Ans sys
setup and then press SELECT.
4. Press ! or
to choose Remote
code and then press SELECT.
5. Press the dialing keys (0-9) to enter
the code, or ! or
to select from
00 to 99, then press SELECT to
save. You hear a confirmation tone.
Description
1
Play all messages.
2
Play only new messages.
3
Delete the current message
(during playback).
33
Delete all old messages.
4
Repeat the current
message (during playback).
5
Stop.
*5
Hear a list of remote
commands.
6
Skip to the next message
(during playback).
*7
Record a new
announcement.
8
End the call.
0
Turn the answering system
on or off.
Call screening
If the answering system and call
screening are on, the announcement
and the incoming message broadcast
at the telephone base while the call is
answered by the answering system.
Options while a message is being
recorded:
! Press /VOLUME or /VOLUME to
adjust the listening volume.
! Press /STOP to temporarily turn off
the call screening.
! Press /PLAY or /VOLUME to
temporarily turn on the call screening if
it is set to off.
4. Hang up or press 8 to end the call.
NOTES
! If you do not press any key after you
enter the remote access code, all new
messages play. If there are no new
messages, all old messages play.
! Once the new messages have played,
the telephone announces the help menu
options. If you do not press any key
within 20 seconds, the remote access call
automatically disconnects.
! When the answering system is turned off,
the telephone answers after 10 rings, and
announces, “Please enter your remote
access code.”
! When the memory is full, the answering
system answers incoming calls after 10
rings and announces, “Memory is full.
Enter your remote access code.”
Call intercept
If you want to talk to the person whose
on
message is being recorded, press
the handset.
23
Record, play or delete memos
Use the built-in answering
system and voicemail
service
Memos are your own recorded
messages used as reminders for
yourself or others using the same
answering system. You can record your
own memos using a system handset.
Playback and delete them in the same
way as incoming messages.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Answering
sys and then press SELECT.
3. Press ! or
to choose Record
memo and then press SELECT.
The handset displays Record
in 5 sec (counting down) and
then Recording... Stop [5] and
announces, “Record after the tone.
Press 5 when you are done.”
4. Speak towards the handset
microphone. Press 5 or OFF when
you finish recording. The handset
announces “Recorded.”
You can use your answering system and
voicemail service together by setting
your answering system to answer before
voicemail service answers as described
below. To learn how to program your
voicemail settings, contact your
telephone service provider.
If you are on a call, or if the answering
system is busy recording a message
and you receive another call, the second
caller can leave a voicemail message.
Set your answering system to answer
calls at least two rings earlier than your
voicemail service is set to answer.
For example, if your voicemail service
answers after six rings, set your
answering system to answer after four
rings. Some voicemail service providers
may program the delay before answering
calls in seconds instead of rings. In this
case, allow six seconds per ring when
determining the appropriate setting.
NOTES
! If you record a memo when the answering
system memory is full, the system
announces, “Memory is full.”
! Each memo can be up to three minutes in
length. Memos shorter than two second
are not recorded.
! When the answering system has less
than three minutes of recording time left,
the handset announces, “Less than three
minutes to record,” and displays Rec mem
low.
24
Retrieve voicemail from
telephone service
Register a handset
When your handset is deregistered from
the telephone base, follow the steps
below to register it back to the telephone
base.
1. Remove the handset from the
telephone base.
2. Press and hold /FIND HANDSET
at the telephone base for about four
seconds until the IN USE light turns
on.
3. Then press # on the handset. It
displays Registering...
Voicemail is a feature available from
most telephone service providers. It may
be included with your telephone service,
or may be optional. Fees may apply.
Retrieve voicemail
When you received a voicemail, the
handset displays and New voicemail.
To retrieve, you typically dial an access
number provided by your telephone
service provider, and then enter a
security code. Contact your telephone
service provider for instructions on how
to configure the voicemail settings and
listen to messages.
The handset show Registered and
you hear a beep when the registration
process completes. The registration
process takes about 60 seconds to
complete.
NOTE
! After you have listened to all new
voicemail messages, the indicators on the
handset turn off automatically.
Turn off the new voicemail
indicators
If you have retrieved your voicemail while
away from home, and the handset still
displays the new voicemail indicators,
use this feature to turn off the indicators.
NOTE
! This feature turns off the indicators only, it
does not delete your voicemail messages.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Settings
and then press SELECT.
3. Press ! or
to choose Clr
voicemail and then press SELECT.
4. The screen displays Reset VM
Icon?. Press SELECT to confirm.
You hear a confirmation tone.
25
Other information
Screen messages
Website
Use this feature to view the VTech
website address.
1. Press MENU when the phone is not
in use.
2. Press ! or
to choose Web
address and then press SELECT.
The screen displays the VTech
website address.
Annc
deleted
Your recorded
announcement is
deleted.
Call log
empty
There are no caller ID log
entries.
Directory
empty
There are no directory
entries.
Directory
full
The directory is full.
Ended
X:XX:XX
You have just ended a
call.
Incoming
call
There is an incoming call.
Line in
use
A system handset is in
use, or another telephone
on the same line is in
use.
LONG
DISTANCE or
L (before the
caller’s number)
It is a long distance call.
Low
battery
The battery needs to be
recharged.
Message
deleted
The message in the
answering system is
deleted.
Microphone MUTE is turned off and
the person on the other
on
end can hear you.
Muted
You have turned off the
handset microphone. The
other party cannot hear
you but you can hear the
other party.
New
voicemail
There are new voicemail
message(s) from the
telephone service
provider.
No battery No battery is installed.
Follow the directions
for battery installation
on page 4 to install the
battery before charging.
26
No line
There is no telephone
line connected.
Saved
Your selection has been
saved.
No
messages
There are no messages
in the answering system.
Unable to
call.
Failed phone call (the
other handset is in use).
Not
available
One handset is already
reviewing the caller ID
log and the other handset
tries to review it.
UNKNOWN
NAME
This caller’s name is
unavailable.
UNKNOWN
NUMBER
This caller’s number is
unavailable.
UNKNOWN
CALLER
No caller information is
available about this caller.
XX missed
calls
There are calls that have
not been reviewed in the
caller ID log.
XX new
messages
There are new messages
in the answering system.
** Paging
**
The system handsets are
being paged.
Number
repeated
The telephone number
you enter is already
stored in the directory.
Out of
range or
no pwr at
base
The handset cannot
communicate with the
telephone base. Check
the telephone base
power connection or
move the handset closer
to the telephone base.
Phone
X:XX:XX
The handset is on a call.
PRIVATE
NAME
The caller is blocking the
name information.
PRIVATE
NUMBER
The caller is blocking
the telephone number
information.
PRIVATE
CALLER
The caller is blocking the
name and the telephone
number information.
Put in
charger
The battery is very low.
Place the handset in
the telephone base or
charger for recharging.
Rec mem
full
The answering system
has no recording time
left.
Rec mem
low
The answering system
has less than three
minutes of recording time
left.
Record in
X sec
You can record your own
announcement or memo
after the tone is played.
Ringer
muted
The handset ringer is
muted temporarily during
an incoming call.
Ringer off The handset ringer is
turned off.
27
General product care
Frequently asked
questions
Taking care of your telephone
Your cordless telephone contains
sophisticated electronic parts, so it must
be treated with care.
Avoid rough treatment
Place the handset down gently. Save the
original packing materials to protect your
telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets
wet. Do not use the handset outdoors
in the rain, or handle it with wet hands.
Do not install the telephone base near a
sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause
power surges harmful to electronic
equipment. For your own safety, take
caution when using electrical appliances
during storms.
Cleaning your telephone
Your telephone has a durable plastic
casing that should retain its luster for
many years. Clean it only with a dry nonabrasive cloth. Do not use dampened
cloth or cleaning solvents of any kind.
Below are the questions most frequently
asked about the cordless telephone.
If you cannot find the answer to your
question, visit our website at
www.vtechphones.com or call
1 (800) 595-9511 for customer service.
My telephone
does not work
at all.
Make sure the telephone
base is installed properly,
and battery is installed
and charged correctly.
For optimum daily
performance, return the
handset to the telephone
base after use.
The display
shows No line.
I cannot hear
the dial tone.
Disconnect the telephone
line cord from your
telephone and connect
it to another telephone.
If there is no dial tone
on that other telephone
either, then the telephone
line cord may be
defective. Try installing a
new telephone line cord.
If changing the telephone
line cord does not help,
the wall jack (or the wiring
to this wall jack) may
be defective. Contact
your telephone service
provider.
You may be using a new
cable or VoIP service,
the existing telephone
jacks in your home may
no longer work. Contact
your service provider for
solutions.
28
I cannot dial
out.
Make sure there is a dial
tone before dialing. It is
normal if the handset
takes a second or two
to synchronize with the
telephone base before
producing a dial tone.
Wait an extra second
before dialing.
Eliminate any background
noise. Mute the handset
before dialing, or dial
from another room in
your home with less
background noise.
The display
shows To
register HS
and See
manual
alternately. The
handset does
not work at all.
The handset is
deregistered from the
telephone base. Follow
the steps in Register
a handset to register
the handset back to the
telephone base.
The display
shows Low
battery.
Place the handset in the
telephone base or charger
for charging.
The battery
does not
charge in the
handset or the
handset battery
does not
accept charge.
Make sure the handset is
placed in the telephone
base or charger correctly.
You may need to
purchase a new battery.
Make sure the ringer
volume is not set to off.
My handset
beeps and is
not performing
normally.
Move the handset closer
to the telephone base. It
may be out of range.
I hear noise on
the cordless
handset and
the keys do not
work.
Make sure the telephone
line cord is plugged in
securely.
Disconnect the telephone
base from the telephone
wall jack. Plug in a
different telephone. If you
still hear other calls, the
problem is probably in
the wiring or telephone
service. Contact your
telephone service
provider.
There is
interference
during a
telephone
conversation.
My calls fade
out when
I am using
the cordless
handset.
The handset may be out
of range. Move it closer to
the telephone base.
If you subscribe to
high-speed Internet
service (DSL - digital
subscriber line) through
your telephone line, you
must install a DSL filter
between the telephone
line cord and the
telephone wall jack. The
filter prevents noise and
caller ID problems caused
by DSL interference.
Contact your DSL
service provider for more
information about DSL
filters.
Appliances or other
cordless telephones
plugged into the
same circuit as the
telephone base can
cause interference. Try
moving the appliance or
telephone base to another
outlet.
If the battery is completely
depleted, charge the
battery for at least
30 minutes before use.
The telephone
does not ring
when there is
an incoming
call.
I hear other
calls when
using the
telephone.
The location of your
telephone base can
impact the performance
of your cordless phone.
For better reception,
install the telephone base
in a centralized location
within your home or
office, away from walls
or other obstructions.
In many environments,
elevating the telephone
base improves overall
performance.
The handset may be too
far from the telephone
base. Move it closer to the
telephone base.
29
The telephone
does not
receive caller
ID or the
telephone does
not show caller
ID during call
waiting.
The answering
system does
not record
messages.
Caller ID is a subscription
service. You must
subscribe to this service
from your telephone
service provider for this
feature to work on your
telephone.
When the answering
machine memory is full,
it does not record new
messages until some old
messages are deleted.
Both your and the
caller’s telephone service
providers must use
equipment compatible
with the caller ID service.
If you subscribe to
voicemail service, change
the number of rings so
that your answering
system answers before
your voicemail service
answers. To determine
how many rings activate
your voicemail service,
contact your telephone
service provider.
The caller may not be
calling from an area which
supports caller ID.
The caller ID information
displays after the first or
second ring.
The display
shows Out of
range or no
pwr at base.
The handset may be out
of range. Move it closer to
the telephone base.
I cannot hear
any instruction
from the
handset when
I try to record,
play or delete
my own
announcement.
The handset does not
have a speakerphone.
When recording,
playing or deleting your
own announcement,
the instructions are
announced through
the handset receiver.
Make sure you place the
handset receiver close to
your ear.
The outgoing
announcement
is not clear.
Make sure the answering
system is on. When the
answering system is on,
ANS ON should display
on the handset and the
telephone base.
Make sure the power cord
is securely plugged into
the telephone base. Use
a working electrical outlet
not controlled by a wall
switch.
When recording the
announcement, make
sure you speak in a
normal tone of voice
towards the microphone
of the handset.
The messages
on the
answering
system are
very difficult to
hear.
Press VOL+ on the
handset or /VOLUME
on the telephone base
to increase the listening
volume.
The answering
system does
not announce
the correct day
of the week
for recorded
messages time
stamp.
Make sure you have
set the date and time.
See !"#$%&'()!%&(
telephone section.
The messages
on the
answering
system are
incomplete.
If a caller leaves a very
long message, part of
it may be lost when
the answering system
disconnects the call after
the preset recording time.
If the memory on the
answering system
becomes full during a
message, the answering
system stops recording
and disconnects the call.
Make sure there is no
background noise when
recording.
If the caller’s voice is
very soft, the answering
system may stop
recording and disconnect
the call.
30
The answering
system does
not respond
to remote
commands.
The RBRC® seal
Make sure you enter the
correct remote access
code.
The RBRC® seal on the nickel-metal
hydride battery indicates that VTech
Communications, Inc. is voluntarily
participating in an industry program to
collect and recycle these batteries at the
end of their useful lives, when taken out
of service within the United States and
Canada.
The RBRC® program provides a
convenient alternative to placing used
nickel-metal hydride batteries into the
trash or municipal waste, which may be
illegal in your area.
VTech’s participation in RBRC® makes it
easy for you to drop off the spent battery
at local retailers participating in the
RBRC® program or at authorized VTech
product service centers. Please call
1 (800) 8 BATTERYTM for information
on Ni-MH battery recycling and disposal
bans/restrictions in your area. VTech’s
involvement in this program is part
of its commitment to protecting our
environment and conserving natural
resources.
RBRC® is a registered trademark
of Rechargeable Battery Recycling
Corporation.
Make sure you are
calling from a touch-tone
telephone. When dialing a
number, there should be
tones. If there are clicks,
then it is not a touch-tone
telephone and cannot
activate the answering
system.
The answering system
may not detect the remote
access code when
your announcement is
playing. Wait until the
announcement is over
before entering the code.
I subscribe to a
nontraditional
telephone
service that
uses my
computer
to establish
connections,
and my
telephone
doesn’t work.
Make sure your computer
is powered on, and
your Internet is working
properly.
Make sure to plug your
USB telephone adapter
into a dedicated USB port
on your computer. Do not
plug into a multiple port
USB hub (USB splitter)
that is not powered.
In a few rare instances,
the USB port on your
computer may not have
enough power. In these
instances, try using a
USB hub with its own
external power supply.
If you are using a firewall,
it may prevent access
to your nontraditional
telephone service.
Contact your service
provider for more
information.
I accidentally
set my LCD
language to
Spanish or
French, and I
don’t know how
to change it
back to English.
While the handset is
not in use, press MENU
and then enter 364# to
change the handset LCD
language back to English.
31
may not cause harmful interference,
and (2) this device must accept
any interference received, including
interference that may cause undesired
operation. Privacy of communications
may not be ensured when using this
telephone.
To ensure safety of users, the FCC
has established criteria for the amount
of radio frequency energy that can be
safely absorbed by a user or bystander
according to the intended usage of the
product. This product has been tested
and found to comply with the FCC
criteria. The handset may be safely
held against the ear of the user. The
telephone base shall be installed and
used such that parts of the user’s body
other than the hands are maintained at
a distance of approximately 20 cm (8
inches) or more.
This Class B digital apparatus complies
with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC, ACTA and IC
regulations
FCC Part 15
This equipment has been tested and
found to comply with the requirements
for a Class B digital device under Part
15 of the Federal Communications
Commission (FCC) rules. These
requirements are intended to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and
can radiate radio frequency energy and,
if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
! Reorient or relocate the receiving
antenna.
! Increase the separation between the
equipment and receiver.
! Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
! Consult the dealer or an experienced
radio/TV technician for help.
FCC Part 68 and ACTA
This equipment complies with
Part 68 of the FCC rules and with
technical requirements adopted
by the Administrative Council for
Terminal Attachments (ACTA). The
label on the back or bottom of this
equipment contains, among other
things, a product identifier in the format
US:AAAEQ##TXXXX. This identifier
must be provided to your telephone
service provider upon request.
The plug and jack used to connect this
equipment to premises wiring and the
telephone network must comply with
applicable Part 68 rules and technical
requirements adopted by ACTA. A
compliant telephone cord and modular
plug is provided with this product.
Changes or modifications to this
equipment not expressly approved by
the party responsible for compliance
could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) this device
32
It is designed to be connected to a
compatible modular jack that is also
compliant. An RJ11 jack should normally
be used for connecting to a single line
and an RJ14 jack for two lines. See the
installation instructions in the user’s
manual.
The Ringer Equivalence Number (REN)
is used to determine how many devices
you may connect to your telephone
line and still have them ring when you
are called. The REN for this product is
encoded as the 6th and 7th characters
following the US: in the product identifier
(e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all
RENs should be five (5.0) or less. For
more information, please contact your
telephone service provider.
This equipment may not be used with
Party Lines. If you have specially wired
alarm dialing equipment connected
to your telephone line, ensure the
connection of this equipment does not
disable your alarm equipment. If you
have questions about what will disable
alarm equipment, consult your telephone
service provider or a qualified installer.
If this equipment is malfunctioning, it
must be unplugged from the modular
jack until the problem has been
corrected. Repairs to this telephone
equipment can only be made by the
manufacturer or its authorized agents.
For repair procedures, follow the
instructions outlined under the Limited
warranty.
If this equipment is causing harm to the
telephone network, the telephone service
provider may temporarily discontinue
your telephone service. The telephone
service provider is required to notify you
before interrupting service. If advance
notice is not practical, you will be notified
as soon as possible. You will be given
the opportunity to correct the problem
and the telephone service provider
is required to inform you of your right
to file a complaint with the FCC. Your
telephone service provider may make
changes in its facilities, equipment,
operation, or procedures that could
affect the proper functioning of this
product. The telephone service provider
is required to notify you if such changes
are planned.
If this product is equipped with a corded
or cordless handset, it is hearing aid
compatible.
If this product has memory dialing
locations, you may choose to store
emergency telephone numbers (e.g.,
police, fire, medical) in these locations. If
you do store or test emergency numbers,
please:
Remain on the line and briefly explain
the reason for the call before hanging up.
Perform such activities in off-peak hours,
such as early morning or late evening.
Industry Canada
This device complies with Industry
Canada licence-exempt RSS
standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation.
Privacy of communications may not be
ensured when using this telephone.
The term ‘’IC:‘’ before the certification/
registration number only signifies that the
Industry Canada technical specifications
were met.
The Ringer Equivalence Number (REN)
33
for this terminal equipment is 1.0. The
REN is an indication of the maximum
number of devices allowed to be
connected to a telephone interface. The
termination on an interface may consist
of any combination of devices subject
only to the requirement that the sum of
the RENs of all the devices does not
exceed five.
This product meets the applicable
Industry Canada technical specifications.
California Energy
Commission battery
charging testing
instructions
This telephone is set up to comply with the
energy-conserving standards right out of
the box. These instructions are intended
for California Energy Commission (CEC)
compliance testing only. When the CEC
battery charging testing mode is activated, all
telephone functions, except battery charging,
will be disabled.
To activate the CEC battery charging
testing mode:
1. Unplug the telephone base power
adapter from the power outlet. Make sure
all handsets are plugged with charged
batteries before proceeding.
2. While you press and hold /FIND
HANDSET, plug the telephone base
power adapter back to the power outlet.
3. After about 30 seconds, when the IN
USE light starts flashing, release /FIND
HANDSET and then press it again within
2 seconds.
NOTES
! When the phone successfully enters the CEC
battery charging testing mode, all handsets
display To register HS and See manual
alternatively.
! When the phone fails to enter this mode, repeat
Step 1 through Step 3 above.
To deactivate the CEC battery charging
testing mode:
1. Unplug the telephone base power
adapter from the power outlet, then plug
it back in. Then the telephone base is
powered up as normal.
2. Register your handsets back to the
telephone base. Refer to Register a
handset.
34
For C-UL compliance only
Mesures de sécurité
importantes
Afin de réduire les risques d’incendie, de
blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives
de base lorsque vous utilisez votre
téléphone :
1. Lisez et comprenez bien toutes les
instructions.
2. Observez toutes les instructions
et mises en garde inscrites sur
l’appareil.
3. Débranchez ce téléphone de la prise
murale avant de le nettoyer. N’utilisez
pas de nettoyeurs liquides ni en
aérosol. N’utilisez qu’un chiffon doux
et légèrement humecté.
4. N’utilisez pas ce produit près de
l’eau, tel que près d’un bain, d’un
lavabo, d’un évier de cuisine, d’un
bac de lavage ou d’une piscine, ou
dans un sous-sol humide ou sous la
douche.
5. Ne déposez pas ce téléphone sur un
chariot, support ou table chancelants.
L’appareil pourrait tomber et être
sérieusement endommagé.
6. Le boîtier de l’appareil est doté de
fentes et d’ouvertures d’aération
situées à l’arrière ou en dessous.
Afin d’empêcher la surchauffe, ces
ouvertures ne doivent pas être
obstruées en plaçant l’appareil sur
un lit, divan, tapis ou autre surface
similaires. Ne placez pas cet
appareil à proximité d’un élément de
chauffage ni d’une plinthe électrique.
De plus, ne l’installez pas dans une
unité murale ou un cabinet fermé qui
ne possède pas d’aération adéquate.
7. Ne faites fonctionner cet appareil
qu’avec le type d’alimentation
8.
9.
10.
11.
12.
35
indiqué sur les étiquettes de
l’appareil. Si vous ne connaissez pas
le voltage de votre maison, consultez
votre marchand ou votre fournisseur
d’électricité.
Ne déposez rien sur le cordon
d’alimentation. Installez cet appareil
dans un endroit sécuritaire, là où
personne ne pourra trébucher sur
la ligne d’alimentation ni le cordon
téléphonique modulaire.
N’insérez jamais d’objets à travers
les fentes et ouvertures de cet
appareil, car ils pourraient toucher
à des points de tension dangereux
ou court-circuiter des pièces, ce qui
constituerait un risque d’incendie ou
d’électrocution. N’échappez pas de
liquides dans l’appareil.
Afin de réduire les risques
d’électrocution, ne démontez pas
l’appareil, mais apportez-le plutôt
à un centre de service qualifié s’il
doit être réparé. En enlevant le
couvercle, vous vous exposez à des
tensions dangereuses ou autres
dangers similaires. Un remontage
inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation
ultérieure de l’appareil. Débranchez
l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide
et doux.
Ne surchargez pas les prises de
courant et les rallonges.
Débranchez cet appareil de la prise
de courant et communiquez avec le
département de service à la clientèle
de VTech dans les cas suivants :
! Lorsque le cordon d’alimentation
est endommagé ou écorché.
! Si du liquide a été échappé dans
l’appareil.
! Si l’appareil a été exposé à une
De tels environnements peuvent
comprendre: des endroits où l’on
utilise de l’oxygène médical sans
ventilation adéquate; des gaz
industriels (dissolvants de nettoyage,
des vapeurs d’essence, etc.); une
fuite de gaz naturel, etc.
15. Ne placez que le combiné de votre
téléphone près de votre oreille
lorsqu’en mode de conversation.
16. Ces adaptateurs ont été conçus pour
être orientés en position verticale
ou montés au sol. Les broches ne
sont pas conçues pour maintenir
l’adaptateur en place si celui-ci est
barnché dans une prise au plafond
ou sous une table/ armoire.
source d’humidité telle que la pluie
ou l’eau.
! Si le produit ne fonctionne pas
normalement en respectant les
instructions de fonctionnement.
Réglez uniquement les
commandes indiquées dans le les
instructions de fonctionnement.
Les réglages incorrects des autres
commandes pourraient provoquer
un dommage qui pourrait exiger
un travail exhaustif de la part d’un
technicien autorisé afin de rétablir
le fonctionnement normal de
l’appareil.
! Si le produit a été échappé et que
le socle et/ou le combiné a été
endommagé.
! Si le produit affiche une nette
diminution de sa performance.
13. Évitez d’utiliser un téléphone (autre
qu’un sans fil) pendant un orage. Les
éclairs peuvent être à l’origine d’une
électrocution.
14. N’utilisez pas le téléphone pour
rapporter une fuite de gaz à
proximité de la fuite. En certaines
circonstances, une flammèche
pourrait être provoquée lorsque
l’adaptateur est branché à une
prise de courant, ou lorsque le
combiné est déposé sur le socle.
Ceci est un événement commun
associé à la fermeture d’un circuit
électrique. L’utilisateur ne devrait pas
brancher le téléphone à une prise de
courant, et ne devrait pas déposer
le combiné chargé sur le socle, si
le téléphone se trouve à proximité
d’un endroit comportant des
concentrations de gaz inflammables,
à moins que la ventilation soit
adéquate. Une flammèche dans
un tel endroit pourrait provoquer
un incendie ou une explosion.
CONSERVEZ CES INSTRUCTIONS
Pile
! MISE EN GARDE : N’utilisez que la
pile incluse.
! Ne jetez pas la pile au feu. Vérifiez les
instructions spécifiques de mise aux
rebus auprès des autorités locales.
! N’ouvrez pas et ne mutilez pas la pile.
L’électrolyte qui s’en échapperait est
corrosif et pourrait causer des brûlures
ou des blessures aux yeux ou à la
peau. L’électrolyte est toxique si avalé.
! Soyez prudents lorsque vous
manipulez les piles afin d’éviter les
courts-circuits provoqués par des
matériaux conducteurs.
! Rechargez la pile incluse avec cet
appareil, selon les instructions et
limites spécifiées dans ce guide
d’utilisation.
Stimulateurs cardiaques implantés
dans l’organisme
Les simulateurs cardiaques (s’applique
uniquement aux téléphones numériques
36
sans fil) :
L’organisme ‘Wireless Technology
Research, LLC (WTR)’, une firme
de recherche indépendante, a mené
une évaluation pluridisciplinaire des
interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques
implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues
(FDA) des États-Unis, la firme WTR
recommande aux médecins :
Avis aux détenteurs de stimulateurs
cardiaques
! Ils doivent tenir le téléphone sans fil
à une distance d’au moins six pouces
du stimulateur cardiaque.
! Ils ne doivent PAS placer le téléphone
sans fil directement sur le stimulateur
cardiaque, tel que dans une poche
de chemise, lorsque celui-ci est en
marche.
! Ils doivent utiliser le téléphone sans
fil en l’appuyant sur l’oreille qui se
trouve dans la direction opposée au
stimulateur cardiaque.
!
!
L’étude effectuée par l’organisme WRS
n’a pas identifié de risque pour les
détenteurs de simulateurs cardiaques
causés par les gens qui utilisent un
téléphone sans fil à proximité de ceux-ci.
!
6(,&!,!2(7'2(*8+8,-!"'2(21"2(#+
!
!"#7'"*01+0*8(9 Les mêmes
caractéristiques qui constituent
des avantages pour les téléphones
sans fil affichent également des
restrictions. Les appels téléphoniques
sont transmis entre le combiné sans
fil et le socle par le biais d’ondes
radio ; il y a donc la possibilité que
vos conversations téléphoniques
sans fil soient interceptées par
des équipements de réception
radio se trouvant dans la portée du
!
37
combiné sans fil. Pour cette raison,
vous ne devez pas percevoir les
communications téléphoniques sans fil
comme étant aussi confidentielles que
celles des téléphones à cordons.
Alimentation électrique : Le socle de
ce téléphone sans fil doit être branché
à une prise électrique fonctionnelle.
La prise électrique ne doit pas être
contrôlée par un interrupteur mural.
Les appels ne pourront pas être
effectués du combiné sans fil si le
socle est débranché ou mis hors
tension ou si le courant est coupé.
Possibilité d’interférences aux
téléviseurs : Certains téléphones
sans fil fonctionnent sur des
fréquences pouvant causer des
interférences aux téléviseurs et aux
magnétoscopes. Pour réduire ou
prévenir de telles interférences, ne
placez pas le socle du téléphone
sans fil près ou sur un téléviseur ou
magnétoscope. S’il y a présence de
parasites, il est conseillé d’éloigner
le téléphone sans fil du téléviseur
ou du magnétoscope afin de réduire
possiblement les interférences.
Piles rechargeables : Manipulez
les piles avec soin afin de ne pas
les court-circuiter avec des bagues,
bracelets ou clés. Les piles ou le
conducteur peut surchauffer et causer
des blessures. Respectez la polarité
adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à
l’hydrure métallique de nickel :
Jetez ces blocs-piles de manière
écologique et sécuritaire. Ne les
incinérez pas et ne les percez pas.
Tel que les autres piles de ce type,
elles pourraient dégager une matière
toxique qui peut causer des blessures
corporelles si elles sont brûlées ou
percées.
Product extends for ONE (1) YEAR from
the date of purchase. If VTech repairs or
replaces a Materially Defective Product
under the terms of this limited warranty,
this limited warranty also applies to the
repaired or replacement Product for a
period of either (a) 90 days from the date
the repaired or replacement Product is
shipped to you or (b) the time remaining
on the original one-year warranty;
whichever is longer.
What is not covered by this limited
warranty?
This limited warranty does not cover:
1. Product that has been subjected
to misuse, accident, shipping or
other physical damage, improper
installation, abnormal operation or
handling, neglect, inundation, fire,
water or other liquid intrusion;
2. Product that has been damaged due
to repair, alteration or modification
by anyone other than an authorized
service representative of VTech;
3. Product to the extent that the
problem experienced is caused by
signal conditions, network reliability,
or cable or antenna systems;
4. Product to the extent that the
problem is caused by use with nonVTech accessories;
5. Product whose warranty/quality
stickers, product serial number
plates or electronic serial numbers
have been removed, altered or
rendered illegible;
6. Product purchased, used, serviced,
or shipped for repair from outside
the United States of America or
Canada, or used for commercial
or institutional purposes (including
but not limited to Products used for
rental purposes);
7. Product returned without a valid proof
Limited warranty
What does this limited warranty
cover?
The manufacturer of this VTech Product
warrants to the holder of a valid proof
of purchase (“Consumer” or “you”)
that the Product and all accessories
provided in the sales package (“Product”)
are free from defects in material and
workmanship, pursuant to the following
terms and conditions, when installed
and used normally and in accordance
with the Product operating instructions.
This limited warranty extends only to the
Consumer for Products purchased and
used in the United States of America and
Canada.
What will VTech do if the Product
is not free from defects in materials
and workmanship during the limited
warranty period (“Materially Defective
Product”)?
During the limited warranty period,
VTech’s authorized service
representative will repair or replace
at VTech’s option, without charge, a
Materially Defective Product. If we
repair the Product, we may use new
or refurbished replacement parts. If we
choose to replace the Product, we may
replace it with a new or refurbished
Product of the same or similar design.
We will retain defective parts, modules,
or equipment. Repair or replacement of
the Product, at VTech’s option, is your
exclusive remedy. VTech will return the
repaired or replacement Products to
you in working condition. You should
expect the repair or replacement to take
approximately 30 days.
How long is the limited warranty
period?
The limited warranty period for the
38
2. Include a “valid proof of purchase”
(sales receipt) identifying the Product
purchased (Product model) and the
date of purchase or receipt; and
3. Provide your name, complete
and correct mailing address, and
telephone number.
of purchase (see item 2 below); or
8. Charges for installation or set up,
adjustment of customer controls,
and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service in the USA,
please visit our website at
www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call
1 (800) 267-7377.
NOTE: Before calling for service, please
review the user’s manual - a check of
the Product’s controls and features may
save you a service call.
Except as provided by applicable law,
you assume the risk of loss or damage
during transit and transportation and
are responsible for delivery or handling
charges incurred in the transport of
the Product(s) to the service location.
VTech will return repaired or replaced
Product under this limited warranty.
Transportation, delivery or handling
charges are prepaid. VTech assumes no
risk for damage or loss of the Product
in transit. If the Product failure is not
covered by this limited warranty, or proof
of purchase does not meet the terms of
this limited warranty, VTech will notify
you and will request that you authorize
the cost of repair prior to any further
repair activity. You must pay for the cost
of repair and return shipping costs for the
repair of Products that are not covered
by this limited warranty.
What must you return with the
Product to get warranty service?
1. Return the entire original package
and contents including the Product to
the VTech service location along with
a description of the malfunction or
difficulty; and
Other limitations
This warranty is the complete and
exclusive agreement between you
and VTech. It supersedes all other
written or oral communications related
to this Product. VTech provides no
other warranties for this Product. The
warranty exclusively describes all of
VTech’s responsibilities regarding the
Product. There are no other express
warranties. No one is authorized to make
modifications to this limited warranty
and you should not rely on any such
modification.
State/Provincial Law Rights: This
warranty gives you specific legal rights,
and you may also have other rights,
which vary from state to state or province
to province.
Limitations: Implied warranties, including
those of fitness for a particular purpose
and merchantability (an unwritten
warranty that the Product is fit for
ordinary use) are limited to one year
from the date of purchase. Some states/
provinces do not allow limitations on
how long an implied warranty lasts, so
the above limitation may not apply to
you. In no event shall VTech be liable
for any indirect, special, incidental,
consequential, or similar damages
(including, but not limited to lost profits
or revenue, inability to use the Product
or other associated equipment, the cost
of substitute equipment, and claims by
third parties) resulting from the use of
this Product. Some states/provinces do
39
.'/-"0/1+(2,'/0#/1*0!"2
not allow the exclusion or limitation of
incidental or consequential damages, so
the above limitation or exclusion may not
apply to you.
Please retain your original sales
receipt as proof of purchase.
40
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
1921.536-1928.448 MHz
Channels
5
Nominal
effective
range
Maximum power allowed by
FCC and IC. Actual operating
range may vary according to
environmental conditions at the
time of use.
Power
requirements
Handset: 2.4V Ni-MH battery
Telephone base:
6V DC @ 400mA
Charger: 6V AC @ 300mA
Memory
Directory:
30 memory locations;
up to 30 digits and
15 characters
Caller ID log:
30 memory locations;
up to 24 digits and
15 characters
Designed to fit your home.
And your life.
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2014 VTech Communications, Inc.
All rights reserved. 05/14. CS6124-X_WEBCIB_V2.0
Document order number: 91-007086-020-100
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages