Miele | VENTILATION SYSTEM DA 230-3 | Operating instructions | Miele VENTILATION SYSTEM DA 230-3 Operating instructions

Miele VENTILATION SYSTEM DA 230-3 Operating instructions
Operating and installation instructions
Ventilation System
DA 230-3
To prevent accidents
and machine damage,
read these instructions
before installation or use.
UV
M.-Nr. 05 853 520
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS
Functional description
Appliance description
Operation
Main power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Turning on the fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Selecting the power level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Delayed Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Turning off the fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Automatic Safety Shut Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Turning the lighting on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dimming the lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Grease filter timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Checking the grease filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reprogramming the grease filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning and care
Cleaning the casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
After Sales Service
Installation instructions
2
IMPORTANT SAFETY INSTRUCTIONS
Read these Operating Instructions carefully before installing or
using the Ventilation System.
This appliance is intended for
residential use only. Use the
appliance only for its intended
purpose. The manufacturer cannot
be held responsible for damages
caused by improper use of the
hood.
This appliance complies with current
safety requirements. Improper use of
the appliance can lead to personal
injury and material damage.
READ AND SAVE THESE
INSTRUCTIONS
CAUTION
For General Ventilating Use Only.
Do Not Use To Exhaust Hazardous
Or Explosive Materials And Vapors.
This appliance is designed to vent
cooking smoke and odors only.
Be certain your appliance is properly installed and grounded by a
qualified technician.
To guarantee the electrical safety of this
appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician. The manufacturer
can not be held responsible for
damages caused by the lack, or
inadequacy of, an effective grounding
system.
Before connecting the appliance to
the power supply make sure that
the voltage and frequency listed on the
data plate correspond with the household electrical supply. This data must
correspond to prevent machine
damage. Consult a qualified electrician
if in doubt.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and other work by unqualified
persons could be dangerous and the
manufacturer will not be held
responsible.
3
IMPORTANT SAFETY INSTRUCTIONS
This equipment is not designed for
maritime use or for use in mobile
installations such as caravans or aircraft. However, under certain conditions
it may be possible for an installation in
these applications. Please contact the
nearest Miele dealer or the Miele Technical Service Department with specific
requirements.
Before servicing or cleaning the
unit, switch power off at the service
panel and lock the service disconnecting means to prevent power from being
switched on accidentally. When the
service disconnecting means can not
be locked, securely fasten a prominent
warning device, such as a tag, to the
service panel.
Before discarding an old
appliance, unplug it from the
power supply and remove the power
cord and any doors to prevent hazards.
Use
Do not allow children to play with
or operate the appliance or its
controls. Supervise its use by the
elderly or infirm.
Be careful when preparing a
flambé beneath the hood.
Flames may be drawn up into the hood
by the suction or grease filters may
catch fire.
Never operate gas burners without
pots.
Do not leave cooking surfaces
unattended while in use. Overheated food, oil and grease can catch
fire.
Do not use the hood without the
grease filters in place.
Clean the grease filters regularly.
Dirty filters are a fire hazard.
Do not use a steam cleaner to
clean the hood. Steam could
penetrate electrical components and
cause a short circuit.
In areas subject to infestation by
cockroaches or other pest, keep
the appliance and its surroundings
clean at all times. Any damage caused
by cockroaches or other pest will not
be covered under warranty.
4
IMPORTANT SAFETY INSTRUCTIONS
, WARNING - TO REDUCE
THE RISK OF A RANGE TOP
GREASE FIRE:
Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers
may ignite. Heat oils slowly on low or
medium settings.
Always turn hood "ON" when cooking at high heat or when cooking
flaming foods.
Clean ventilating fans frequently.
Grease should not be allowed to
accumulate on fan or filter.
Use proper pan size. Always use
cookware appropriate for the size
of the surface element.
, WARNING
TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
SMOTHER FLAMES with a close
fitting lid, cookie sheet, or metal
tray, then turn off the burner.
BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
NEVER PICK UP A FLAMING
PAN - You may be burned.
DO NOT USE WATER, including
wet dishcloths or towels - a violent
steam explosion will result.
Use an extinguisher
ONLY IF:
– You know you have a Class ABC
extinguisher, and you already know
how to operate it.
– The fire is small and contained in the
area where it started.
– The fire department is being called.
– You can fight the fire with your back
to an exit.
5
IMPORTANT SAFETY INSTRUCTIONS
Installation
, WARNING
To reduce the risk of fire, only
use metal ductwork.
When installing the hood, follow the
recommended minimum safety
distances between a Miele cooktop and
the hood:
– 22" (55 cm) above electric cooktops,
– 26" (65 cm) above gas cooktops,
– 26" (65 cm) above an open grill.
If local building codes require a greater
safety distance, follow their requirement.
For non-Miele cooking appliances
maintain the safety distances recommended by the appliance manufacturer
in their installation and operating
instructions.
If there is more than one appliance
beneath the hood and they have different minimum safety distances always
select the greater distance.
Be careful not to damage hidden
electrical wiring or plumbing when
cutting or drilling into the wall or ceiling.
Do not use an extension cord to
connect the appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance, (e.g.
danger of overheating).
Do not install this hood over
cooktops burning solid fuel.
Any fittings, sealant, or materials
used to install the ductwork must
be made of approved non-flammable
materials.
6
Never connect an exhaust hood to
an active chimney, dryer vent, vent
flue, or room ventilating ductwork. Seek
professional advice before connecting
an exhaust hood vent to an existing,
inactive chimney or vent flue.
Ducted fans must always be
vented outdoors.
Make sure that the airflow in the
room is sufficient for combustion
and exhausting of all non-electric heating appliances (water heaters, gas
cooktops, gas ovens, etc.), otherwise
backdrafts may occur. Follow the heating manufacturer’s guidelines and
safety standards or those published by
the National Fire Protection Association
(NFPA), or the American Society for
Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE).
If in doubt, consult an experienced
professional.
Functional description
The ventilation hood works by air extraction. The air is drawn in and
cleaned by the grease filters and directed outside.
The hood comes equipped with a
non-return flap. This flap automatically
closes when the hood is turned off so
that no exchange of outside air and
room air can occur. When the hood is
turned on, the air pressure of the exhaust fan automatically opens the flap
blowing the inside air and cooking
odors outside.
7
Appliance description
8
Appliance description
a Cover plate
h Light button
b Chimney
This button turns the light on and off
and also dims the light.
c Canopy
The lighting can be used independently
of the fan.
d Control panel
e Grease filters
i On/Off button
j Fan power level buttons
f Overhead lighting
Four fan speed selection.
g Main power switch
k Delayed Shut Down
This button activates the Delayed Shut
Down feature. The fan can be set to
turn off automatically after either 5 or 15
minutes.
l Grease filter button
The indicator next to the grease filter
button lights when the grease filters
need to be cleaned.
This button is also used:
– to reset the grease filter timer after
cleaning the grease filters (see
"Cleaning and Care").
– to show how long the grease filter
has been in use (see "Operation /
Grease filter timer").
– to change the number of hours
counted by the grease filter timer
(see "Operation / Reprogramming the
grease filter timer").
9
Operation
Main power switch
Intensive setting
Level "4" (yellow indicator) should be
used for a short period when frying or
cooking food with a strong aroma.
Press the main power switch to "I". The
fan and the lighting can now be operated.
If the appliance is not going to be used
for a long period of time (e.g. while vacationing) turn the appliance off by
pressing the main power switch to "0".
Fan performance
The maximum air flow capacity is
625 cfm. Factors such as narrow duct
diameter and bends will affect this
value.
The next time it is turned on, the hood
will operate at the level previously used.
Level 1 operates at 40% capacity
Level 2 operates at 60% capacity
Level 3 operates at 80% capacity
Level 4 operates at 100% capacity
Turning on the fan
Delayed Shut Down
^ Press the On/Off button.
If odors or smoke remain in the kitchen
after cooking has been completed, the
Delayed Shut Down feature can be selected to allow the hood to continue
running for either 5 or 15 minutes.
The fan runs at power level "2".
The On/Off indicator lights.
Selecting the power level
^ Use the _ buttons to select the
desired power level.
& =increases the fan speed
$ =decreases the fan speed
Level "1" to "3" (green indicators) are
usually sufficient for normal cooking.
10
^ Press the Delayed Shut Down button
while the fan is still running.
Press once = 5 minute delay
(left indicator lights)
Press twice = 15 minute delay
(right indicator lights)
To cancel the Delayed Shut Down feature press the button again.
Operation
Turning off the fan
Turning the lighting on/off
The overhead lighting can be turned on
and off independently of the fan.
^ Press the On/Off button to turn the
fan off.
The indicator goes out.
Automatic Safety Shut Off
The fan will turn off automatically
10 hours after the last button was activated. The lighting however will remain
on.
^ Press the light button briefly to turn
on the lighting.
The light button indicator illuminates.
^ Press the light button briefly again to
turn off the lighting.
The light button indicator will go out.
Dimming the lighting
^ Press the On/Off button to turn the
fan back on again.
The brightness of the lighting can be
adjusted.
^ While the lighting is turned on, press
the light button.
The lighting will dim until the button is
released.
^ If the button is pressed again, the
lighting will brighten until the button is
released.
If the button is pressed continuously,
the light will cycle between bright and
dark.
^ Press the light button again to turn off
the lighting.
11
Operation
Grease filter timer
Checking the grease filter timer
A timer monitors the hours of fan operation. The indicator for the grease filter
will light after 30 hours of operation. The
grease filters must then be cleaned.
To check the percentage of time already used:
After the grease filters have been
cleaned and put in place, the grease filter timer must be reset.
^ To do this, press the grease filter button for about 3 seconds.
^ Press the On/Off button to turn the
fan on.
^ Press the grease filter button.
The indicator will go out.
The number of flashing _ indicators
show the percentage of programmed
hours that have been used.
1 indicator = less than 25 %
2 indicators = less than 50 %
3 indicators = less than 75 %
4 indicators = less than 100 %
This information will remain stored in
memory in the event of a power failure.
12
Operation
Reprogramming the grease filter
timer
The grease filter timer is preset to 30
hours. This time can be lengthened or
shortened to 20, 30, 40 or 50 hours.
– A time of 20 hours should be programmed in kitchens with frequent
pan or deep frying.
– A time of 20 hours should also be
programmed if the kitchen is only
used occasionally. Otherwise grease
which has accumulated over a long
period of time will harden on the filters making cleaning more difficult.
^ Press the On/Off button to turn off the
fan.
^ Press the Delayed Shut Down and
grease filter buttons at the same time.
The indicator for the grease filter and
one of the _ indicators will flash.
The lit _ indicator shows the programmed time:
1st indicator from the left
2nd indicator from the left
3rd indicator from the left
4th indicator from the left
=
=
=
=
20 hours
30 hours
40 hours
50 hours.
^ Use the $ or & button to select the
desired time.
^ Store the selection by pressing the
grease filter button.
If the procedure is not stored within
4 minutes of programming, the hood
will automatically default to the "old"
data.
13
Cleaning and care
Before cleaning or servicing the
hood, disconnect it from the power
supply by either removing the fuse,
unplugging it from the outlet or manually "tripping" the circuit breaker.
Cleaning the casing
,Never use abrasive cleaners,
scouring pads, steel wool or caustic
(oven) cleaners on the hood. They
will damage the surface.
^ All external surfaces and controls can
be cleaned with warm water and liquid dish soap applied with a soft
sponge.
^ Wipe dry using a soft cloth.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
Avoid:
– cleaning agents containing soda, acids or chlorides,
– abrasive cleaning agents e.g. powder or cream cleansers,
– abrasive sponges, e.g. pot scourers
or sponges which have been previously used with abrasive cleaning
agents.
These will damage the surface.
14
Stainless steel
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
To help prevent resoiling, a conditioner
for stainless steel can also be used.
Apply sparingly with even pressure.
Stainless steel colored controls
These controls may become discolored or damaged if not cleaned regularly.
Do not use a stainless steel cleaner
on these controls.
Cleaning and care
Grease filters
The reusable metal grease filters remove solid particles from the vented
kitchen air (grease, dust, etc).
The grease filters should be cleaned
every 3-4 weeks or whenever the
grease filter timer indicator lights.
A dirty filter is a fire hazard.
^ Clean the filters
- by hand: use a scrub brush in
warm water with a mild detergent.
- in a dishwasher: place the filters in
the lower basket, making sure that
the spray arm is not blocked.
Depending on the detergent, cleaning the grease filters in a dishwasher
may cause permanent discoloration
of the filter surface. Performance of
the filter will not be affected by this
discoloration.
^ After cleaning, the filters can be
placed on a towel to air dry.
^ While the filters are removed, clean
any dirt or grease from the filter casing to prevent the risk of fire.
When putting the grease filters back
make sure that the locking clips are visible facing down towards the cooking
surface.
^ To remove the grease filters press the
locking clips in towards the middle of
the filter. Holding carefully, lower and
remove the filter.
If the filters are incorrectly installed, insert a small screwdriver into the slit
along its edge to disengage it from the
casing.
^ After returning the grease filters,
press the grease filter button for
3 seconds to reset the timer. The indicator light will go out.
^ If the grease filters are cleaned before the timer has reached its maximum, the grease filter button should
be pressed for 6 seconds to reset the
counter to zero.
15
Cleaning and care
Changing the light bulb
To change a bulb:
Before changing the light bulbs, disconnect the hood from the power
supply by either removing the fuse,
unplugging it, or manually "tripping"
the circuit breaker.
When in use halogen bulbs become
extremely hot, and they can burn
your hands. Do not attempt to
change the bulbs until they have
had sufficient time to cool down.
Do not touch the bulb surface. Fingerprints or body oils deposited on
the bulb will decrease the life of the
bulb. Please follow the bulb manufacturer’s instructions.
^ Remove the outer ring, a.
^ Support the glass, c, while detaching the circlip, b. Be careful not to let
the glass fall out.
^ Pull the old bulb, d, out of its socket
and replace it with a new one.
^ Reinstall the glass, circlip and outer
ring.
Never use the lights without the
glass, c, installed. The glass is specially made to filter harmful light
rays.
16
After Sales Service
In the event of a fault which you cannot
correct yourself please contact:
– Your Miele Dealer
or
– The Miele Technical Service
Department
USA
1-800-999-1360
techserv@mieleusa.com
CDN
1-800-565-6435
service@miele.ca
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance.
These are shown on the data plate
which is visible when the grease filter is
removed.
17
18
Installation instructions
Table of Contents
Caring for the environment
Structural support
Electrical data
Appliance dimensions
Installation
Air extraction
20
Caring for the environment
Disposal of packing material
Disposal of an old appliance
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Before discarding an old hood, unplug it from the outlet and cut off its
power cord to prevent hazards.
21
Structural support
The ceiling mounting plate will support the weight of the hood. This
ceiling plate must be attached to
rigid structural framing that is supported in its entirety by the ceiling
joists, or to the ceiling joists directly.
Do not attach the plate directly to the
ceiling by using anchors, mollies or
toggle bolts.
22
Electrical data
All electrical work should be performed by a qualified electrician in
strict accordance with national and
local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer can
not be held responsible for unauthorized work.
Ensure that power to the appliance
is OFF while installation or repair
work is performed.
Verify that the voltage, load and circuit
rating information found on the data
plate (located behind the grease filters), match the household electrical
supply before installing the hood.
Important
The hood must be hard wired accordingly:
Black/Red wire:. . . . connect to L1 (live)
White wire: . . . . . connect to N (neutral)
Green wire: . . connect to GND (ground)
Maximum load . . . . . . . . . . . . . . . 350 W
Lighting . . . . . . . . . . . . . . . . . . 4 x 20 W
Voltage . . . . . . . . . . . . . . . . . . . . . 120 V
Frequency . . . . . . . . . . . . . . . . . . 60 Hz
Circuit rating. . . . . . . . . . . . . . . . . . 15 A
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Miele’s Technical Service Department.
USA 1-800-999-1360
CDN 1-800-565-6435
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
23
Appliance dimensions
a Mounting bolt holes
b Cut out for power cord
c Exhaust connection 6" (150 mm) diameter
24
Installation
Do not install this exhaust hood over
cooktops burning solid fuel.
When installing the hood, make sure
that the following minimum distance (S) between the top of a Miele
cooking surface and the bottom of
the hood is:
- 22" (55 cm) above electric cooktops
- 26" (65 cm) above gas cooktops
- 26" (65 cm) above an open grill
For non-Miele cooking appliances
maintain the safety distances recommended by the cooktop manufacturer in their installation and operating instructions.
If there is more than one appliance
beneath the hood and they have different minimum safety distances always select the greater distance.
See "Warning and Safety instructions" for further information.
26" (65 cm) is recommended for all installations to allow for optimum work
space under the hood.
^ Make a line on the ceiling going from
the rear of the cooktop towards the
front and centered over the cooktop.
^ Cut a 7 1/2" (190 mm) hole in the ceiling for the exhaust duct to pass
through. The exhaust connection has
a 6" (150mm) diameter.
CAUTION:
During the installation process,
please be careful of sharp edges
that can cause harm.
25
Installation
^ Position the mounting plate and align
the notches with the guide line.
Mark the position of the four holes to
be drilled a for securing the mounting plate and determining the position of the hole b the power cord will
feed through.
^ Feed the ductwork and power cord
through their respective openings in
the ceiling.
If 6" (150mm) diameter ducting is not
possible then 5" (125 mm) ducting can
be used in conjunction with a reducing
collar available from the Miele Technical
Service Department (see "Installation /
"Air extraction").
26
^ Drill four 3/16" (5 mm) holes in the ceiling.
The S10 wall anchors included in the
packaging are not for use in
USA/CDN.
Be certain that the ceiling is stable
enough to support the hood.
Installation
^ Secure the ducting to the mounting
plate using a hose clip.
^ Insert the short edge of two spring
clips into their slots from below and
position so that the tab faces the center of the mounting plate.
^ Pull the power cord through the
mounting plate.
^ Insert the four countersunk screws
M 6 x 20 into the recessed holes from
above.
Tape the screws from above to prevent them from being pushed upwards when the nuts are tightened.
27
Installation
^ Secure the mounting plate to the ceiling using the 8 x 60 lag bolts. Once
tight, make sure that the mounting
plate can safely support the weight of
the hood.
^ Pull the power cord through its cut
out on the flange of the chimney.
^ Using at least two people, lift the
hood and guide the spring clips
through their respective slots in the
flange at the top of the chimney.
Make sure they click into place and
that the hood is hanging securely
from the spring clips before allowing
them to carry the weight.
28
Installation
^ Bolt the flange firmly to the ceiling using the four M6 nuts.
^ Shorten the power cord as much as
possible and attach it to the terminal
block inside the chimney (see "Electrical data").
Before connecting the appliance
read the "Warning and Safety Instructions" and the "Electrical data"
sections.
^ Finally, being careful not to scratch
the chimney, push the cover plate up
and onto its locking pins until it clicks
into place. If installed correctly, the
cover should be secure and flush
against the ceiling.
^ Before using the appliance remove
the grease filter and remove the protective foil from the filter frame. Return the filter.
29
Air extraction
Danger of toxic fumes.
Gas cooking appliances release
carbon monoxide that can be harmful or fatal if inhaled. The exhaust
gases extracted by the hood
should be vented outside of the
building only.
Do not terminate the exhaust
ducts in attics, garages,
crawlspaces, etc.
Please read and follow the "Warning
and Safety Instructions" to reduce the
risk of personal injury. Follow all local
building codes when installing the
hood.
– Use smooth or flexible pipes made
from approved non-flammable materials for exhaust ducting.
– Where the ductwork is horizontal, it
must slope away from the hood at
least 1/8" per foot (1cm per meter) to
prevent condensation dripping into
the appliance.
– If the exhaust is ducted through an
outside wall, a Miele Telescopic Wall
Vent can be used.
Exhaust ducting and connections
– The ducting should be as short and
straight as possible, and the number
of sharp bends should be minimized.
– For most efficient air extraction, the
diameter of the ductwork should not
be less than 6" (150 mm). Use of flat
ducts also reduces the air extraction
efficiency.
– Noise levels of the hood will increase
if flat ducts or round ducts of less
than 6" (150 mm) in diameter are
used.
WARNING
To reduce the risk of fire, only use
metal ductwork.
CAUTION
To reduce risk of fire and to properly
exhaust air, be sure to duct air outside. Do not vent exhaust air into
spaces within walls or ceilings or
into attics, crawl spaces, or garages.
30
– If the exhaust is ducted into an inactive flue, the air must be expelled
parallel to the flow direction of the
flue.
Air extraction
Never connect an exhaust hood to
an active chimney, dryer vent, vent
flue, or room venting ductwork. Seek
professional advice before connecting an exhaust hood vent to an existing, inactive chimney or vent flue.
Ductwork with a diameter of less
than 6" (150 mm) should only be
used when absolutely necessary. As
duct diameter decreases, the hood’s
performance and sound levels will
be affected.
Important:
If the ductwork runs through rooms,
ceilings, garages, etc. where temperature variations exist, it may need to be
insulated to reduce condensation. In
some cases, a condensate trap may
also be required to collect and evaporate any condensate which may occur.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the exhaust outlet.
31
Alteration rights reserved / 5002
M.-Nr. 05 853 520 / V00
This paper consists of cellulose which has been bleached without the use of chlorine.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising