advertisement
▼
Scroll to page 2
T E C H N I C A L 12 CHANNEL 2.4 kVA WALL MOUNTING DIMMER RACK DESCRIPTION Dimensions: The Jands FP12WM is a wall mounting high quality, rugged, 12 channel 2.4 kVA per channel dimmer rack specifically designed for contracting / theatre applications. A separate wall bracket simplifies the installation process. It allows cabling to be routed to the dimmer location prior to the installation of the actual dimmer units, providing the contractor with the ability to fit off the dimmers when the site is secure. As an option, a 24 way patch panel kit is available which, when combined with the extended wall mounting bracket, provides the end user with an economical and compact combined dimmer rack/patch system. * * * * * * * * Net/shipping weight: 23kg SUPPLIED ACCESSORIES • 1 wall/rack mounting bracket • 1 operating manual ORDERING INFORMATION MODEL/PART PART NO. 12 2.4 kW dimming channels DMX-512 digital control protocol DMX-512 terminating switch Suitable for permanent installations Soft turn on characteristic Low acoustic / electrical noise Toroidal chokes Three mains phase indicator LEDs "DMX-IN" LED for DMX-512 signal indication “STATUS” LED for dimmer status indication Two DMX-bank select switches Built-in test facilities Dimmer curve set for linear relationship between the control input and output power Compensates for fluctuations in the mains supply voltage and minimises the effect of superimposed control tones, ensuring a constant light output and increased lamp life May be rack mounted, attached to a wall by means of the supplied mounting brackets or flown using hook clamps Microprocessor control Built-in captive nuts for rigged applications Single or three phase operation Over-temperature cutout Pre-heat facility Dimmer will hold last DMX value should control data be interrupted • FP12WM with 12 hard wired outputs JND-FP12WM-H • Extended wall mounting bracket JND-WM-EBP • Patch kit (Refer to the Technical Specification Sheet of WM-Patch) • 40 Amp flexible lead & DMX socket kit JND-WM-FLEX (Factory fitted at time of ordering) Conduit cable entry OVERALL SPECIFICATIONS Channels: Power rating: Power supply type: Power requirements: Current: Dissipation: Dimmer curve: Max. ambient operating temp: Control input: Output connectors: Output risetime: Output protection: Test facility: 12 2.4 kVA (10A/240V) per channel 3-phase, 240V phase-to-neutral (415V phase-to-phase) with neutral and earth 3-phase 240 VAC / 50 Hz, 40 A/phase max, full size (40 A) neutral required plus earth 40 Amps per phase (max.) <1% of output load (288W max.) Linear power 40˚C DMX-512/1990 protocol 1 Australian 3-pin 10 Amp outlet per channel (export models may vary) > 130 µs (10%~90%) 12 10A thermal/magnetic circuit breakers 12-way channel selection using DMX select switches JND-FP12WM-A 12 CHANNEL 2.4 kVA WALL MOUNTING DIMMER RACK- * 482mm(W)158mm(D)485mm(H) (with wall mounting bracket) • FP12WM with 12 10 Amp Australian outlets FEATURES * * * * * * * * * * * * * S H E E T ▲ FP12WM dimmer shown with supplied wall/rack mounting bracket and optional extended mounting bracket / patch kit FP12WM FP12WM S P E C I F I C A T I O N T E C H N I C A L S H E E T 12 CHANNEL 2.4 kVA WALL MOUNTING DIMMER RACK 15 0m m 219mm DANGER HIGH VOLTAGE 1 NO USER SERVICEABLE PARTS INSIDE 2 3 4 5 6 7 8 9 10 11 12 1 PHASE 2 3 DMX IN STATUS BANK SELECT DIMMER POWER SUPPLY ● 230V phase to neutral (200V~265V) ● 400V phase to phase (345V~460V) ● 50Hz AC only (48Hz~52Hz) ● Three phases + Neutral + Earth ● Full sized neutral required SY STEM D I M M E R T E C H N I C A L 2 SURFACE MOUNTED CONDUIT S Y S T E M 440mm ▲ FP12WM dimmer rack 88mm 28mm 482mm ▲ Optional extended wall mounting bracket ▲ Supplied wall mounting bracket 3 Jands Electronics Pty Ltd 40 Kent Road Mascot NSW 2020 Australia Phone: +61 (0)2 9582 0909 Fax: +61 (0)2 9582 0999 Internet: www.jands.com.au S P E C I F I C A T I O N S CABLE TRAY (shown with top/bottom conduit plates removed) S H E E T Specifications subject to change without notice. Manufactured by Jands Electronics Pty Ltd ACN 001 187 837. Note: While all due care has been taken in the preparation of this document, Jands Electronics shall not be liable for any inaccuracies or omissions which may occur herein. 12 CHANNEL 2.4 kVA MOUNTING DIMMER RACK THROUGH WALL CABLE ENTRY D I M M E R TSS-FP12WM-0506-05 1 S Y S T E M 485mm Mechanical The dimmer rack shall be designed to either mount in a standard 19-inch equipment rack or be permanently attached to a wall with the supplied wallmounting brackets. The dimmer rack shall be 440 mm wide 130 mm deep 485 mm high. The dimmer rack shall have angled sides to minimise the chassis profile and facilitate ease of patching when installing multiple racks. The dimmer rack shall be constructed of 1.2 mm steel, and shall be provided with a removable panel for access to internal electronics. All chassis surfaces shall be properly treated and finished in powdercoat or zinc passivating. The control surface shall be scratch-resistant 0.25 mm Lexan with legends reverse silk-screen printed from behind. All operator controls and indicators shall be provided on the front face of the dimmer. The dimmer rack chassis shall be designed to allow for adequate convection cooling, provided the ambient temperature does not exceed 40˚C (113˚F). A separate wall mounting bracket shall allow the contractor to install the cabling to the proposed dimmer location, prior to the actual on- site installation of the dimmer unit itself. An optional extended mounting bracket shall ● Maximum input current 46A per phase ● Maximum output 10A per outlet 12 Manufactured by Jands Electronics Pty Ltd ACN 001 187 837 40 Kent Road Mascot NSW 2020 Australia 485mm Electrical The dimmer rack shall operate from a three-phase plus neutral and earth supply of 415 volts AC phase-to-phase, and with a nominal supply frequency of 50 Hz (60Hz selectable). The dimmer rack shall feature twelve (12) identical channels capable of driving 2.4 kW loads. All channel outputs shall be protected by 10 amp thermalmagnetic circuit breakers. FP12WM Electronics The dimmer rack shall receive and decode banks of twelve (12) control signals complying with the industry standard USITT DMX-512/1990 protocol. If the DMX signal is interrupted, the dimmer outputs shall default to the last received DMX frame. The DMX circuitry shall incorporate an internal DMX Terminate switch to minimise signal reflections on long signal lines. The dimmer rack shall have a control response time of not more than ten (10) milliseconds, input to output. The dimmer rack shall utilise two miniature BCD rotary switches to select the DMX bank allocated to that dimmer. The dimmer rack shall match a control input to power output in a linear relationship. Each of the twelve (12) dimmer channels shall smoothly control loads from 25 watts to 2400 watts. The dimmer rack shall utilise Toroidal chokes which are acoustically quiet and provide a risetime in excess of 130 microseconds. The dimmer rack shall be factory tested and cyclically burned-in for a minimum of 24 hours. facilitate the installation of the dimmer in situations where the wiring is surface mounted or run in conduits. The dimmer rack shall easily interlock with the wall brackets by means of a dual tongue-and-slot arrangement to facilitate cable installation. The dimmer shall be the JANDS FP12WM. 130mm ARCHITECTS & ENGINEERS SPECIFICATION 485mm FP12WM S P E C I F I C A T I O N S
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project