Acer | AL2416 | Technical information | Acer AL2416 Technical information

Acer AL2416W
Service Guide
Service guide files and updates are available on the
CSD web: for more information,
Please refer to http://csd.acer.com.tw/
-1-
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any
means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission
of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or
warranties, either expresses or implied, with respect to the contents hereof and specifically disclaims any warranties of
merchantability or fitness for any particular purpose, Any Acer Incorporated software described in this manual is sold or
licensed “as is ”. Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated,
its distributor, of its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
-2-
Conventions
The following conventions are used in this manual:
Screen messages
Denotes actual messages that appear on screen
Note
Gives bits and pieces of additional information related to the current topic.
Warning
Alerts you to any damage that might result from doing or not doing specific actions.
Caution
Gives precautionary measures to avoid possible hardware or software problems.
Important
Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1. this Service Guide provides you with all technical information relating to the BASICCONFIGURATION
decided for Acer’s “global” product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2. please not WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide, for ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
Service of customer machines.
-3-
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception,
Which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Warning
Use only shielded signal cables to connect I/O devices to this equipment. You are cautioned that changes or
modifications not expressly approved by the party responsible for comliance could viold your authority to operate the
equipment.
®
®
As an ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
WARNING:
To prevent fire or chock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are
present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
-4-
PRECAUTIONS
z
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub,
Swimming pool or in a wet basement.
z
Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and
cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacture or sold
with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacture and
follow the kit instructions.
z
Slots and openings in the back and bottom of the cabinet area provided for ventilation. To ensure reliable
operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered.
Do not place the monitor on a bed, sofa, rug or similar surface. Do not place the monitor near or over a radiator
or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
z
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of
the type of power supplied to your home, consult your dealer or local power company.
z
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.
z
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
z
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
z
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
z
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel.
z
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100-240V AC, Min. 3.5A.
z
The wall socket shall be installed near the equipment and shall be easily accessible.
-5-
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES
z
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and
then turn it on again to make sure the flicker disappears.
z
You may find slightly uneven brightness in the screen depending on the desktop pattern you use.
z
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a
missing pixel or a pixel lit all of the time.
z
Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,
when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or
turning off the Power Switch for hours.
-6-
Table of contents
Chapter 1 Monitor Feature
…………………………………………………………………...………..8
INTRODUCTION...............................................................................................................................................................8
ELECTRICAL REQUIREMEENTS....................................................................................................................................9
MONITOR BLOCK DIAGRAM ....................................................................................................................................... 19
BLOCK DIAGRAM ......................................................................................................................................................... 20
MONITOR BOARD LAYOUT ......................................................................................................................................... 21
SOFTWARE FLOW CHART .......................................................................................................................................... 22
GENERAL INSTRUCTIONS .......................................................................................................................................... 23
SYSTEM INSTALLATION .............................................................................................................................................. 24
POWER/INVERTOR BOARD ........................................................................................................................................ 29
SAFETY ......................................................................................................................................................................... 32
Chapter 2 Operating Instruction ………………………………………………..……………………..34
CONTROLS ................................................................................................................................................................... 34
MAIN OSD MENU .......................................................................................................................................................... 35
OSD MESSAGE............................................................................................................................................................. 37
PLUG AND PLAY ........................................................................................................................................................... 39
WHITE COLOR TEMPERATURE.................................................................................................................................. 40
AUDIO TECHNICAL SPECIFICATION .......................................................................................................................... 40
Chapter 3 Machine Disassembly and Replacement
…………………………………..…………41
DISASSEMBLY PROCEDURE ...................................................................................................................................... 41
Chapter 4 Troubleshooting …………………………………………………………………………..44
TROUBLESHOOTING ................................................................................................................................................... 44
Chapter 5 Connector Information …………………………………………………………………..48
CONNECTOR INFORMATION ...................................................................................................................................... 48
Chapter 6 FRU List …………………………………………………………………………………… 49
PART LIST...................................................................................................................................................................... 49
Chapter 7 Schematic Diagram ….……………………………………………………………………..54
SCHEMATIC DIAGRAM ................................................................................................................................................ 54
-7-
Chapter 1
Monitor Feature
INTRODUCTION
Scope
This specification defines the requirements for the 24” MICRO-PROCESSOR based Multi-mode
supported high resolution color LCD monitor. This monitor can be directly connected to general 15
pin D-sub VGA connector and eliminates the requirement of optional special display card. It also
supports VESA DPMS power management and plug & play function. There is a build-in stereo
audio amplifier with volume control to drive a pair of speakers.
Description
The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no
radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop space,
and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF target is
20k hours or more.
Comparison Chart of AL2416W
Comparison Chart of AA668 & AA868
AA668
Normal 24” panel
AA868
Normal 24” panel
LTM240M1-L01
LTM240M1-L01
Signal Interface
Sync Type for analog
input
D-SUB
D-SUB & DVI-D
Separate / compatible /
Separate / compatible /
Color Temp user adjust
Support
Support
DDC
Speaker
Headphone Jack
Microphone Jack
USB Hub
Tilt / Swivel
Height Adjust
DDC2B
DDC2B
NO
NO
No
Not support
No / No
Option
NO
NO
No
Not support
No / No
Option
Panel
-8-
ELECTRICAL REQUIREMENTS
Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified.
225 lux
Ambient light :
50 cm in front of LCD panel
Viewing distance :
Warrn up time
All specifications :
30 minutes
Fully functional :
5 seconds
Chroma 2250 signal generator or equivalent, directly
Measuring Equipment :
Connected to the monitor under test.
Minolta CA100 photometer, or equivalent
Control settings
User brightness control :
Maximum (unless otherwise specified )
User contrast control:
Typical (unless otherwise specified )
User red/white balance,
Green/white balance and
Blue/white balance control :
In the center (unless otherwise specified )
Power input:
110Vac or 230Vac
Ambient temperature:
Analog input mode:
Digital input mode:
20 ± 5 ˚C ( 68 ± 9 ˚ F)
1280 x1024 /60 Hz
1920x1200/60Hz (For AA868)
MEASUREMENT SYSTEMS
The units of measure stated in this document are listed below:
1 gamma = 1 nano tesla
1 tesla = 10,000 gauss
cm = in x 2.54
lb = kg x 2.2
degrees F = [°C x 1.8] + 32
degrees C = [°F - 32]/1.8
u' = 4x/(-2x + 12y + 3)
v' = 9y/(-2x + 12y + 3)
x = (27u'/4)/[(9u'/2) - 12v' + 9]
y = (3v')/[(9u'/2) - 12v' + 9]
nits = cd/(m2) = Ft-L x 3.426
lux = foot-candle x 10.76
-9-
LCD Panel Specification
LCD Panel Model
(LTM240M1-L01-L00)
- 10 -
Note 1) Definition of Viewing Angle: Viewing angle range (10≤CR)
Note 2) Definition of Contrast Ratio (CR): Ratio of gray max(Gmax),gray min(Gmin) at the
center point of panel.
CR=
Luminance with all pixels white (Gmax)

Luminance with all pixels black (Gmin)
Note 3) Definition of Response time: Sum of
TR , TF
Note 4) After stabilizing and leaving the panel alone at a given temperature for 30 min, the
measurement should be executed .Measurement should be executed n a stable,
windless ,and dark room.30 min after lighting the back-light. This should be
measured in the center of screen. Dual lamp current :13.0mA(6.5mA x2)(Refer to
the note(1) in the page 14 for more information ).
Environment condition :Ta=25±2°C
- 11 -
Optical characteristics measurement setup
Notes 5) Definition of Luminance of White : measure the luminance of white at center point.
Notes 6)Definition of 9 points brightness uniformity (Measuring points: Refer to the Note 5)
AU
BUNI=
Bmin
 X 100%
Bmax
Samsumg
- 12 -
BUNI=
Bmax-Bmin
 X 100%
Bmax
Bmax: Maximum brightness
Bmin: Minimum brightness
Notes 7) Definition of Flicker level
F
Flicker Voltage pp
=  x 100 %
LMD Voltage dc
♦ One maximum value of three estimated values.
♦ For this test ,an LMD(Light Measurement Device)is needed with adequate response time
to track any visible rate flicker component and with a voltage level output proportional
To luminance intensity.
♦ Test Pattern: For dot inversion Driving(Gray levels of foreground dots on the test panel
Are G22,G32,and G45)
♦ Test Point :Center point of the display area
Note 8) Definition of Crosstalk
(Refer to the VESA STD)
The calculation for shadowing is made from the 2 luminance measurements Gbkg and Lsh,
as follows:
Lmax -Lmin
- 13 -
CT
=  x100 %
Lmin
Where Lmax is the larger value of Gbkg or Lsh , and Lmin is the smaller of the two.
♦ To determine background and foreground levels (colors),first set the background to any
gray scale or color level suitable for shadowing determination.(Note that it may take
several iterations of adjusting background level and box levels to determine the proper
value for the background .Next display the box levels to determine the proper value for the
background level. Look for shadowing in any direction from box E. Independently vary the
gray level (or color) of the background and box E until the worst case shadowing is
observed. This defines the background (Gbkg) and foreground (Gfg) levels to be
maintained for the remainder of the test.
♦ One point only (the target) will be measured. To determine that point proceed as follows
Using the background and foreground gray levels of step1 (Gbkg and Gfg). Turn on each
box at a time. Look for the case with the worst shadowing. The box causing the worst case
is the shadowing source, or Bsrc. Use Bsrc and the box opposite from it that lies directly in
the shadow path. That is the target box, or Btgt. Note that box Eight be either Bsrc or Btgt,
depending on the shadowing conditions, but typically Bsrc and Btgt will be a pair of
opposite boxes, A&C or B&D. Btgt will only be displayed for aligning the LMD. It will be
turned off for the actual measurement.
♦
The target box point (Btgt) will be measured with the source box (Bsrc) turned on then off.
(Btgt is for alignment purpose only) Display the background only at level Gbkg. Display
Btgt determined in step 2 above. Using the correct distance, angle, and measurement
aperture, align the LMD to the center of the Btgt. Turn off Btgt. With Gbkg set to its
proper level, measure the luminance (or color). Next,turn on the source box Bsrc. Again
measure at the center point of Btgt (without Btgt present.). In this case the LMD will be
measuring the shadowing level, Lsh.
- 14 -
Panel Relative Humidity
JP777-E02
Input Signals
Video input
•
•
•
•
•
Type
Analog R, G, B.
Input Impedance
75 ohm +/- 2%
Polarity
Positive
Amplitude
0 - 0.7 +/- 0.05 Vp
Display Color
same as LCD panel
Sync input
• Signal
separate horizontal and vertical sync, or composite sync
which are TTL compatible
• Polarity
positive and negative.
Interface frequency
The following frequency range is generalized by supported timing. If the entered
mode does not match the supported timing the display optimization will not be
assured.
• Horizontal Frequency 24KHz --80KHz
• Vertical Frequency 49Hz -------75Hz
- 15 -
Supported Timing
FH(KHZ)
SYNC
TOTAL
ACTIVE
FV(HZ)
POLARITY
(DOT/LINE)
(DOT/LINE)
31.469
70.087
24.83
56.42
31.469
70.087
31.5
70.15
31.469
50.030
31.469
59.94
35.00
66.67
37.861
72.809
37.5
75
31.469
70.087
49.725
74.55
35.156
56.25
37.879
60.317
48.077
72.188
46.875
75
48.363
60.004
53.964
66.132
56.476
70.069
60.023
75.029
60.24
75.02
54.054
59.270
63.851
70.012
67.50
75.00
60.00
60.00
70.00
70.00
75.00
75.00
64
60
80
75
75
60
74.6
60
+
–
–
–
–
+
–
–
–
–
–
–
–
–
–
–
–
+
–
–
+
+
+
+
+
+
+
+
–
–
+
+
–
–
+
+
–
–
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
800
449
848
440
800
449
800
449
800
629
800
525
864
525
832
520
840
500
900
449
1152
667
1024
625
1056
628
1040
666
1056
625
1344
806
1328
816
1328
806
1312
800
1328
803
1480
912
1480
912
1600
900
1800
1000
1800
1000
1800
1000
1688
1066
1688
1066
2160
1250
2592
1245
640
350
640
400
640
400
640
400
640
480
640
480
640
480
640
480
640
480
720
400
832
624
800
600
800
600
800
600
800
600
1024
768
1024
768
1024
768
1024
768
1024
768
1152
864
1152
864
1152
864
1280
960
1280
960
1280
960
1280
1024
1280
1024
1600
1200
1920
1200
SYNC
FRONT
BACK
PIXEL
TIMING
640x350
VGA-350
640x400
NEC PC9801
640x400
VGA-GRAPH
640x400
NEC PC9821
640x480
VESA-PAL
640x480
VGA-480
640x480
APPLE MAC-480
640x480
VESA-480-72Hz
640x480
VESA-480-75Hz
720x400
VGA-400-TEXT
832x624
APPLE MAC-800
800x600
SVGA
800x600
VESA-600-60Hz
800x600
VESA-600-72Hz
800x600
VESA-600-75Hz
1024x768
XGA
1024x768
COMPAQ-XGA
1024x768
VESA-768-70Hz
1024x768
VESA-768-75Hz
1024x768
APPLE MAC-768
1152x864
60Hz
1152X864
60Hz
1152x864
60Hz
1280x960
60Hz
1280x960
70Hz
1280x960
75Hz
1280x1024
VESA-1024-60Hz
1280x1024
VESA-1024-75Hz
1600x1200
VGSA-1200-60Hz
1920x1200
VGSA-1200-60Hz
WIDTH
(DOT/LINE)
96
2
64
8
96
2
64
2
96
2
96
2
64
3
40
3
64
3
108
2
64
3
72
2
128
4
120
6
80
3
136
6
176
4
136
6
96
3
96
3
96
3
96
3
128
2
112
3
112
3
112
3
112
3
144
3
192
50
200
6
PORCH
(DOT/LINE)
16
37
64
7
16
12
16
13
16
62
16
10
64
3
16
1
16
1
18
12
32
1
24
1
40
1
56
37
16
1
24
3
16
8
24
3
16
1
32
3
40
13
32
1
64
2
96
1
96
1
96
1
48
1
16
1
64
1
136
3
PORCH
(DOT/LINE)
48
60
80
25
48
35
80
34
48
85
48
33
96
39
120
20
120
16
54
35
224
39
128
22
88
23
64
23
160
21
160
29
112
36
144
29
176
28
176
29
192
32
200
44
256
32
312
36
312
36
312
36
248
38
248
38
304
46
336
36
FOREQ.(MHZ)
25.175
21.05
25.175
25.197
25.175
25.175
30.24
31.5
31.5
28.322
57.2832
36
40
50
49.5
65
71.664
75
78.75
80
80
94.499
108.00
108.00
126.00
135.00
108
135
162
193
Note: Mode 640x350, 640x400 and 720x400 will locate on middle position but cannot be expanded to full screen on
vertical direction
- 16 -
Support Modes
There will be 28 total support modes to accommodate the above mode and other video modes within the frequency range of the
monitor.
85Hz refresh rate Support
Monitor should display 85Hz refresh rate mode as emergency mode.
Monitor should display “Out of Range” warning menu at this mode.
Video input Connector
Analog Video input Connector: 15pins mini D-Sub
Table 2.4.5. Pin assignment for D-sub connector
Separate Sync
PIN NO.
1
RED VIDEO
2
GREEN VIDEO
3
BLUE VIDEO
4
GROUND
5
GROUND
6
RED GROUND
7
GREEN GROUND
8
BLUE GROUND
9
PC5V (+5V DDC)
10
CABLE DETECTION
11
GROUND
12
SDA
13
H.SYNC
14
V.SYNC
15
SCL
- 17 -
Color of plastic parts: Blue (PC99)
5
1
10
6
15
11
D-sub connector
Digital Video input Connector: DVI-D (For AA868 only)
Table 4-3-3. Pin assignment for DVI-D (24pin) connector
Pin – Assignment of DVI –D connector :
1
TX2-
9
TX1-
17 TX0-
2
TX2+
10
TX1+
18 TX0+
3
Shield (TX2 / TX4)
11
Shield (TX1 / TX3)
19 Shield (TX0 / TX5)
4
NC
12
NC
20 NC
5
NC
13
NC
21 NC
6
DDC-Serial Clock
14
+5V power *)
22 Shield (TXC)
7
DDC-Serial Data
15
Ground (+5V)
23 TXC+
8
No Connect
16
Hot plug detect
24 TXC-
*) In case, the power of the PC unit is switched off and the power of the monitor is switched on,
no voltage may occur at pin 14.
- 18 -
MONITOR BLOCK DIAGRAM
The LCD monitor will contain an main board, an inverter/ power board, key board and internal adapter which house the
flat panel control logic, brightness control logic and DDC.
The inverter board will drive the backlight of panel and the DC-DC conversion.
The Adapter will provide thr 12V DC-power to inverter/ power board.
Power board
(include: AC/DC,inverter)
- 19 -
BLOCK DIAGRAM
System Block Diagram
- 20 -
Monitor board layout
LABEL
Component
LABEL
Component
U2
EEPROM SOIC-8 24C02
CN2
D-SVB 15 PIN
U5
GM1601
CN5
P-TWO AFN300-N2G1Z 30P P1 90D
U8
HY5DU283222AF
CN7
E&T 4300-09 9P P1.25
U9
AIC 1084-33V
CN8
E&T 4500-12 12P P2.0
U10
APL1117-1.8V
CN9
E&T 4500-12 12P P2.0
U11
APL1117-25V
U13
APL5883-33DC
XU1
FL 512K8 PLSST39VF040
- 21 -
Software flow chart
- 22 -
General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor.
By changing these settings, the picture can be adjusted to your personal preferences.
z
The power cord should be connected.
z
Connect the video cable from the monitor to the video card.
z
Press the power button to turn on the monitor position. The power indicator will light up.
External Controls
1
Auto Adjust Key/Exit
4
MENU/ENTER
2
<
5
LED
3
>
6
- 23 -
/ Power Key
System Installation
Connecting the Display
z
Power off your computer.
z
Connect one end of the signal cable to the LCD Monitor’s VGA port.
z
Connect the other end of the signal cable to the VGA port on your PC.
z
Make sure connections are secure.
Connecting the AC Power
z
Connect the power cord to the LCD Monitor.
z
Connect the power cord to an AC power source.
- 24 -
Gap Spec.
The step between front bezel and back cover shall be within specification.
Top and Bottom
Left and Right
Back cover & Bezel concavity
Back cover & Bezel concavity
0.8mm ≤ A ≤ 1.3 mm
0.8mm ≤ A ≤ 1.3 mm
Back Cover & Hinge Cover concavity
0mm ≤ B ≤ 0.5mm
- 25 -
Base & Neck concavity
0mm ≤ C ≤ 0.6mm
Top and Bottom
Left and Right
Back cover & Bezel step
Back cover & Bezel step
0mm ≤ D ≤ 0.8 mm
0mm ≤ D ≤ 0.8 mm
- 26 -
LCD Horizontally
The angle between front bezel and LCD unit in bottom side should not large than 1.0mm.
The distance of the LCD display unit from left side to right should not large than 4.0mm.
- 27 -
Tilt Base Rotation
Tilt up 15 ± 2°/ down 5 ±2°
Plastic Material
For TCO99
Front Bezel
Back Cover
The Others
For MPRII
Front Bezel
Back Cover
The Others
PC+ABS
PC+ABS
ABS 94HB
ABS 94V-0
ABS 94V-0
ABS 94HB
GAP Spec.
Gap between panel with bezel is 0 mm < gap < 1.5 mm
Swivel title noise spec.
When adjust the monitor angle, the range should be limited -5º~ +15º and it should not have any
noise.
- 28 -
POWER/Inverter Board
Description
This specification defined the performance and characteristic of power/inverter board.
It supplies the following outputs :
1). 5Vdc: Logic power.
2). 24Vinv: Inverter power.
Features
Input Voltage: 100 ~ 240 ±10%Vac
Input Frequency: 47 ~ 63Hz
Total output power: 110Wmax
Inverter brightness adjustment: Burst mode
Protection function: auto-recovery type
Interface Signals
Input
AC Inlet: HUAJIE SA-4S-066 or compatible.
Output Connector & Pin Assignment:
1.CNS1 (to logic board),type :E&T 4500 or equivalent.
PIN NO. Function
Function
1
+5Vstb
2
GND
Power Ground
3
GND
Power Ground
4
GND
Power Ground
5
+5Vcc
+5Vdc, connected to main board
6
+5Vcc
+5Vdc, connected to main board
7
+5Vcc
+5Vdc, connected to main board
8
+12Vcc Audio power (N/A option)
9
GND
+5Vdc for standby output
Signal ground
10
Power on (24V/5Vcc)Enable signal , Active : 2V~5V, off<1V
11
Backlight Backlight On/Off control signal, connected to CNS3#12
on/off
Dimmer Brightness control, connected to CN3#13,bright
max.=3.3V,min.=0V.
12
- 29 -
2.CNS3 (to Inverter board),type :E&T 4500 or equivalent.
PIN NO. Function
Function
1
2
3
4
+24Vcc
+24Vcc
+24Vcc
+24Vcc
Inverter Vcc
Inverter Vcc
Inverter Vcc
Inverter Vcc
5
6
+24Vcc Inverter Vcc
GND Inverter GND
7
GND
Inverter GND
8
GND
Inverter GND
9
GND
Inverter GND
10
GND
Inverter GND
11
N.C
N.C
12
13
14
Backlight Backlight On/Off control signal, connected to CNS1#11
on/off
Dimmer Brightness control, connected to CN1#12,bright
max.=3.3V,min.=0V.
N.C
N.C
2.Inverter-side connecter : YEONHO 20015 HS-04L or equivalent.
PIN NO. Function
1-1
Hot1
1-2
N.C
1-3
N.C
1-4
Hot2
Comment
High voltage
High voltage
PIN NO. Function
1
Function
+5Vaudio Audio power (optional).
2
3
4
GND
GND
GND
Audio ground
Ground
Ground
5
Vbri
Brightness control from logical board (0V to 3.3V)
6
----
-----
7
Ven
8
+5Vdc
Inverter enable signal from logical board (high active ,
>3V)
+5Vdc supply for logical board
9
+5Vdc
+5Vdc supply for logical board
10
+5Vdc
+5Vdc supply for logical board
- 30 -
Output Requirement
Output
Output Voltage
1
*
Total Regulation*
1
Current
MIN.
TYP.
MAX.
+5Vstb (VCC)
+5 %/ -5%
0.05A
1.0A
1.2A
+5Vcc
+5 %/ -5%
0.0A
2.0A
2.2A
+24VInverter
+5 %/ -5%
0.0A
3.3A
3.5A
Total Regulation includes (1) Line Regulation (2) Load Regulation (3) Cross Regulation
Output Ripple/Noise: +/- 3% maximum
3.4.1.3
Protection function
1) SCP: Short circuit protection must be acted on both outputs
2) OPP: Should be protected when output power consumption is within 130W .
3.4.1.4 Overshoot: +10% or less Full Load
3.4.1.5 Dynamic Loading: +5% or less Full Load
3.4.1.6 Efficiency: 75% min. at full load condition.
INVERTER BOARD
DESIGNED FOR SAMSUNG LTM240M!-L01
MIN.
TYP.
MAX.
COMMENT
INPUT VOLTAGE
22.8V
24V
25.2V
24V+/-5%
INPUT CURRENT
--------
3.3A
--------
Vin=24V,Vbrite=3.3V
Normal BACKLIGHT
VOLTAGE
--------
1800Vrms
--------
LAMP CURRENT
(every lamp)
--------
6mArms
7mArms
DRIVING FREQUENCY
40KHz
---------
60KHz
EFFICIENCY
--------
75%
--------
Vin ON/OFF sequence
--------
0.5S
--------
OLP TIME
--------
1S
--------
30%
--------
100%
0V
--------
3.3V
--------
500cd/m2
--------
Strike voltage at 0°C
3540Vrms
--------
--------
Strike voltage at 25°C
2830Vrms
--------
--------
Operating life time
30,000 hrs
--------
--------
BRIGHTNESS RANGE
Brightness control
Brightness
- 31 -
Each CCFL
Vin = 24V,max
Open lamp protection
3.3V, brightness max.
SAFETY
Leakage Current: 0.25mA @ 100Vac
Insulation Resistance: more than 3M ohms while withstanding a voltage of 500Vac
Hi-Pot: 3Kvac with using 3mA cut off current
Power Consumption
The monitor is equipped with a power-management according to the below.
There is a delay of 5s … 7s before the transition from On-state to any power saving state to avoid
unintentionally entering of a power saving stage during display resolution and timing mode changes.
Transition from any power saving state to another can be instantaneous.
The recovery from Off-state requires no manual power on.
Mode
H-Sync.
V-Sync.
Video
Pw-cons.
Indicator
Rec. time*
Power-On
on
on
active
< 110W
Green
--
LED
DPMS-off
off
off
blanked
<2W
Orange
< 5S
LED
DC-Switch-off
< 1 W@100VAC
Dark LED
SYNC. On means: Normal operation
SYNC. Off means:
H sync.
F < 10KHz duty cycle > 25%
V sync.
F < 10Hz
duty cycle > 25%
CONNECTORS / CONTROLS
Connectors
Power
Analog RGB
-
: Monitor rear side
: AC Inlet
: Monitor rear side / Data Cable
: 15-pin D-sub female / male
Pin – Assignment of 15-pin D-sub:
-
1
Red Video
9
+5V FOR DDC
2
Green Video
10
Detect
3
Blue Video
11
Serial Data for ISP
4
Serial Clock for ISP
12
Serial Data for DDC
5
Ground
13
H-Sync.
6
Red Ground
14
V-Sync.
7
Green Ground
15
Serial Clock for DDC
8
Blue Ground
Audio
: Monitor rear side
:
-PC I/P for PC
: 3.5mm Stereo female
- 32 -
Monitor Control Keys
KEY :
Power , Menu , Adjust +/- , Vol +/-, Auto
Position Of Controls
Position of all switches
: Bottom side of front bezel
Position of LED
: Bottom side of front bezel
- 33 -
Chapter 2
Operating Instructions
CONTROLS
Control panel (monitor front panel)
1. Power ON/OFF switch, push to ON and push to OFF. (toggle switch)
2. Power LED, will be green when monitor is on; be amber when in power saving mode.
3. Function select.
4. Adjust increase.
5. Adjust decrease.
6. Auto adjust.
- 34 -
Main OSD Menu:
Outline:
(option)
The description for control function :
Main Menu
Sub Menu
Sub Menu
Icon
Item
Icon
Contrast
Description
Adjustment
Reset Value
Range
Contrast from Digital-register.
0-100
Recall Cool
Contrast Value
Brightness
Backlight Adjustment
0-100
Recall Cool
Brightness Value
Focus
Adjust Picture Phase to reduce
0-100
Do Auto Config
0-100
Do Auto Config
Adjust the horizontal position of the 0-100
Do Auto Config
Horizontal-Line noise
Clock
Adjust picture Clock to reduce
Vertical-Line noise.
H. Position
picture.
V. Position
Adjust the verticalposition of the
0-100
Do Auto Config
N/A
The Color
picture.
Warm
Cool
N/A
N/A
Recall Warm Color Temperature
from EEPROM.
Temperature will be
Recall Cool Color Temperature from N/A
set to Cool.
EEPROM.
User / Red
Red Gain from Digital-register.
0-100
100
User / Green
Green Gain Digital-register.
0-100
100
User / Blue
Blue Gain from Digital-register.
0-100
100
- 35 -
English
N/A
Set OSD display language to
N/A
be set to English.
English.
繁體中文
N/A
The Language will
Set OSD display language to
N/A
Tranditional Chinese.
Deutsch
N/A
Set OSD display language to
N/A
German.
Français
N/A
Set OSD display language to
N/A
French.
Español
N/A
Set OSD display language to Spain. N/A
Italiano
N/A
Set OSD display language to Italian. N/A
简体中文
N/A
Set OSD display language to
N/A
Simplified Chinese.
日本語
N/A
Set OSD display language to
N/A
Japanese.
H. Position
Adjust the horizontal position of the 0-100
50
OSD.
V. Position
Adjust the verticalposition of the
0-100
50
10-120
10
OSD.
Adjust the OSD timeout.
OSD Timeout
Auto Config
N/A
Auto Adjust the H/V Position, Focus N/A
N/A
and Clock of picture.
N/A
Source
N/A
N/A
Show the resolution, H/V frequency N/A
N/A
Analog and Digital source change.(option)
Change
Information
N/A
and input port of current iput timing.
Reset
N/A
Clear each old status of
N/A
N/A
N/A
N/A
Auto-configuration and set the color
temperature to Cool.
Exit
N/A
Exit OSD
- 36 -
OSD Message:
Outline:
The description for OSD Message :
Item
Description
Auto Config
When User Press Hot-Key “Auto”, will show this message, and the monitor do the auto config
Please Wait
function.
Input Not
When the Hsync Frequency, Vsync Frequency or Resolution is out of the monitor support range,
Supported
will show this message. This message will be flying.
Cable Not
When the video cable is not connected, will show this message. This message will be flying.
Connected
No Signal
When the video cable is connected, but the is no active signal input, will show this message, then
enter power saving.
LOGO:
When the monitor is power on, the LOGO will be showed in the center.
Item of Factory menu
Vendor may customize design and add adjustment items Factory menu as far as all required items are included.
- 37 -
1) Bright
Adjust Brightness and Contrast value to Max.
2) Auto Balance
Adjust each R, G, B contrast (gain) and offset.
Method of auto adjust is depends on hardware.
Adjusted value of R, G, B gain shall be used for initial value of Contrast in user menu.
All value shall be adjustable manually.
This function shall be located in 3. tag of Factory menu.
3) Factory color temp data edit
Following data for color temp shall be editable manually.
-color temp default preset No.
- 38 -
Plug and play
Plug & play DDC2B feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor
to inform the host system of its identity and, depending on the level of DDC used, communicate additional information
about its display capabilities. The communication channel is defined in two levels, DDC2B.
2
The DDC2Bis a bidirectional data channel based on the I C protocol. The host can request EDID information over the
DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER
FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards Association(VESA) and/or
the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This
feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal
present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an
OFF mode. This reduces the monitor’s internal power supply consumption. After the video input signal is restored, full
power is restored and the display is automatically redrawn. The appearance is similar to a “Screen Saver” feature
except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.
Using The Right Power Cord
The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed
and CSA labeled. The voltage rating for the power cord shall be 125 volt AC.
Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a
minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type
attachment plug, rated 10A, 250V,CEE-22 male configuration. The other end terminates with a molded-on type
connector body, rated 10A, 250V, having standard CEE-22 female configuration.
Please note that power supply card needs to use VDE 0602, 0625, 0821 approval power cord in European counties.
- 39 -
White Color Temperature
White color temperature is 4 preset as 9300, 7500,6500 and User,
Default value of user color should be user which is maximum setting for panel.
Target of color setting
Color
Color Coordinate
Tolerance
Color Coordinate
Tolerance
Temp.
x
y
9300K
0.283
0.297
6500K
0.313
0.329
User
-
-
u’
v’
+0.03
0.189
0.446
u’v’ < 0.01*
+0.03
0.198
0.469
u’v’ < 0.01*
-
-
-
*) TCO’0X A.2.6.1 requirement
User should follow “Microsoft Windows Color Quality Specification for Liquid Crystal Display OEM’s”.
(http://www.microsoft.com/hwdev/tech/color/ColorTest.asp)
Electrical characteristics (Tamb=25°)
Audio amplifier(USE Panasonic VP-7723A Audio Analyzor. )
Item
Audio Input
Freq.
Comment
Spec.
Min.
Typ.
Max.
-
0.5Vm
-
Input Voltage(V)
s
Input Current(m A)
-
500
800
-
-
6dB
Audio Voltage Gain
500m Vrms 1KHz
Frequency Response
500m Vrms 300Hz-20KH -10dB
Volume Max.,load 4 Ω
-
+10d B Volume Max.,load 4 Ω
-
-40dB Volume Max.,load 4 Ω
z
Signal to Noise ratio
500m Vrms 1KHz
-
Total harmonic distortion
500m Vrms 1KHz
Cross talk
500m Vrms 1KHz
-
-
-30dB Volume Max.,load 4 Ω
Output Watt.
500m Vrms 1KHz
-
-
0.5W
-
-
-
1%
Volume Control
40
except speakers distortion
Volume Max.,load 4 Ω
Analog
Chapter 3
Machine Disassembly and Replacement
Disassembly Procedure
Disassemble the base
1. Remove the neck cover.
2. Remove the four screws to release the hinge.
3. Remove the base
Disassemble the chassis
1. Remove the five screws to release the back cover.
2. Remove the two screws to release the EMI cover from chassis.
3. Remove the Main Board, Power Board, Inverter and Key Board. (See the next page for detail.)
4. Remove the six screws from chassis then take the chassis.
5. Remove the four screws from chassis and release the panel.
41
Disassemble the main board
1. After remove EMI cover from chassis.
2. Remove the four screws from chassis.
3. Remove the four screws from chassis and release the main board.
4. Disassemble audio line from power board.
5. Disassemble two VL-VK lines from VL board.
6. Disassemble power line from VL board.
7. Disassemble FPC line from VL board.
Disassemble the power board
1. After remove main board then disassembly the power board.
2. Remove the three screws from power.
3. Remove the four screws from power.
4.
5. Disassemble two voltage lines from power board.
6. Remove the one screw to release line from Chassis.
7. Remove the three screws from Chassis.
8. Remove the two screws to release power board from Chassis.
9. Then take the power board from the chassia.
Disassemble the Inverter and key board
1. Remove the one screw to release VK board from bezel.
2. Disassemble the two speaker lines from VK board.
42
43
Chapter 4
Troubleshooting
Main Procedure
44
Power Circuit and Backlights Troubleshooting
45
Performance Troubleshooting
46
Function Troubleshooting
47
Chapter 5
Connector Information
Video input Connector
Analog Video input Connector: 15pins mini D-Sub
Table 2.4.5. Pin assignment for D-sub connector
Separate Sync
PIN NO.
5
1
10
15
6
11
48
1
RED VIDEO
2
GREEN VIDEO
3
BLUE VIDEO
4
GROUND
5
GROUND
6
RED GROUND
7
GREEN GROUND
8
BLUE GROUND
9
PC5V (+5V DDC)
10
CABLE DETECTION
11
GROUND
12
SDA
13
H.SYNC
14
V.SYNC
15
SCL
Chapter 6
FRU (Field Replaceable Unit) list
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of AL1916. Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
NOTE : Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available
on your regional web or channel(http://aicsl.acer.com.tw/spl/). For whatever reasons a part number change is
made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED CERVICE PROVIDERS, your
Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts repair and
service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on
how best to dispose it, or follow the rules set by your regional Acer office on how to return it.
49
50
13.1.11.4 Material List by Location
Date: 05/31/05
Time: 19:39:25
R/N:ydr6069j - D1H
===================================================================================================
=================================
QUANTITY REQUIRED
DWG.NO.
582H01
REV. 0A
C NO.
PART NO.
DESCRIPTION
SPECIFICATION
------------------------------------------------------30
001
REMARKS
- ---- ----------- ------------------------ ------------------------------ --- --- --- --- --- ----- ----- ----- ----- ----- ----# 582H0130001 DIS UNIT ABO
LAA668 24"SAM 1920X1200
1 AC6VA2400R0 LCD MODU
2 DC0201933R0 H-CON SET
3 DC0201934R0 H-CON SET
4 DC020193500 H-CON SET
5 DC020193700 H-CON SET
6 NBX30000263 FFC
7 PK07V0033R0 INVERTER
8 PK101V0110I PWR MODU
9 461ACY30001 FIRMWARE CTRL/B
10 454AC830011 PCBA KEY/B
11 X66AUV30001 MEC PARTS ABO
LTM240M1-L01-L00 24"B A Acer
1 - - 301
AA668 POW-INV 14P
1 - - 304
AA668 POW-LOG 12P
1
- - - 305
AA668 CTRL-KEY 9P-8P
1 - - 306
AA668 CTRL-PANEL POWER 12P
1
- - - 307
30P F P1.0 PAD1.0 AA668 SUM24"
1
- - - 308
AA668 24" TBD292LF TDK
1 - - 309
FSP130-4F01GP 5V/12V/24V DV89A 1
- - - 310
VL-2401 LAA668A ABO
1
- - - 351
VK-922 LAA668
1
- - 353
LAA668
1 - - 355
End of Report
51
Part list
No.
Photo
Part Name
Part No.
1
Hinge Cover
FAAA6622000
2
Base
FAAA661A000
3
BACK Cover ASSY
FAAA6613000
4
STAND
FAAA6610000
5
EMI COVER ASSY
EEAA6617000
52
6
MB
461ACY30001
9
Power Board to MB
cable
AU: 453AC530051
Samsung: 453AC530051
7
Power Board
PK101V0110I
8
Inverter Board
PK07V0033I0
9
Front Bezel ASSY
FAAA6611000
10
Keyboard to MB
Cable
DC020193500
53
13
Frame
ECAR9915A00
14
LCD (R)
AC6VA2400R0
15
Panel to MB cable
NBX30000263
16
Function Board
54
454AC830011
Chapter 7
Schematic Diagram
55
56
57
58
59
60
61
Download PDF

advertising