GEM-P801 v2 Installation Manual
333 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440
®
Publicly traded on NASDAQ
Symbol: NSSC
GEM-P801 Control Panel/Communicator
For use with the GEM-RP8 or the GEM-K800 Keypads
Installation Instructions
GEMINI
I
H
ED
ARM
U
STAT
1
GEMINI
2
3
4
5
6
7
H
S
A 1 2 3
B 4 5 6
J
E
F
C 7 8 9 0 G
COMPUTERIZED SECURITY SY STEM
For use with the GEM-RP8 Keypad
© NAPCO 2007
I
8
ED
ARM
1
2
3
4
5
6
7
8
TUS
STA
R 1 2 3
B 4 5 6
J
P
Q
C 7 8 9 0 G
COMPUTERIZED SECURITY SYSTEM
For use with the GEM-K800 Keypad
WI1089A 1/07
WI1089A GEM-P801 Installation Instructions
Table of Contents
General Information ................................................. 2
GEM-P801 Features................................................ 2
Specifications .......................................................... 3
UL Compatible Smoke Detectors ............................. 4
Listings and Approvals ............................................ 4
Ordering Information................................................ 4
Optional Accessories ............................................... 4
Programming the Panel ........................................... 5
Installation ............................................................... 6
Wiring ...................................................................... 6
Keypad Operation ................................................... 7
Panel Operation ...................................................... 8
Bypassing ............................................................... 9
User Program Mode ................................................ 9
GEM-P801 Commands............................................ 10
Dealer Commands .................................................. 11
Wireless Operation (Signal Strength) ..................... 11
Zone Features ......................................................... 12
Test Mode ............................................................... 12
System Times.......................................................... 13
System Features ..................................................... 14
Telephone Number 1 Programming ......................... 16
Backup Telephone Programming............................. 17
Pager Programming ................................................ 17
Telephone Number 3 Programming ......................... 18
Report Codes .......................................................... 18
Enhanced Communicator Features ......................... 19
SIA CP-01 /Misc. Features ..............................................19
Wireless .................................................................. 20
Downloading ........................................................... 21
Dealer Programming ............................................... 22
Download-Only Features ......................................... 23
SIA CP-01 Quick Reference Chart...................................25
System Troubles ..................................................... 26
Troubleshooting....................................................... 28
GEM-P801 Wiring Diagram ..................................... 30
Limited Warranty ..................................................... 32
2
General Information
The GEMINI GEM-P801 control panel provides up
to 6 hardwired/wireless zones, a 2-wire fire zone
and 2 wireless only zones. Up to eight 4-digit
user codes can be programmed. Ambush, when
selected, uses User 8 code as an Ambush code.
The GEM-P801 is wireless ready. When used
with a GEM-RECV-XP8 receiver, the control panel
can support up to 8 wireless zones, 4 wireless
smoke detectors and 4 Keyfobs.
The GEM-K800 keypad provides complete control
of the GEM-P801 control panel. Information on
system status, bypassed zones, system troubles
etc. can be viewed at the keypad.
The control panel can be easily and quickly
programmed from the keypad. The panel can also
be locally or remotely downloaded using PCDWindows Version 5.0 or later software and a
PCI2000/3000 interface or PCL2000B local
Download cable. See Downloading Section (pg.
5) for more information.
GEM-P801 Features
Control Panel
•
•
•
•
•
•
•
•
8 Zones (6 Hardwired/Wireless + 2 wireless)
2-wire Fire Zone
3 Keypad Panics
Wireless Ready
Bell Supervision
Line Cut Detection
Answering Machine Override (Second Call)
50 Event Log
Communicator
•
•
•
•
•
•
•
2 Telephone Numbers
Backup Reporting
Pager Format
Point ID Format
Individually Report 8 Users
Opening after Alarm Report (Cancel Code)
Conditional Closing Report
IMPORTANT NOTE This manual supports keypad programming with both the older GEM-RP8 and the new GEMK800 "K Series" keypad (which offers new STAY / AWAY / MENU and ENTER buttons). While this manual only
depicts the GEM-K800 keypad buttons, either keypad may be used. Note: For consistency, it is recommended
that all keypads either be all "classic" or all "K Series"--both keypad types should not be used in one alarm system. Program Mode is the same for both keypads; only the button names have changed, as follows:
The A / R buttons and the D / U buttons operate identically (in Program Mode) for both keypads.
The E / P ("NEXT / YES") buttons operate identically (in Program Mode) for both keypads.
The F / Q ("PRIOR / NO") buttons operate identically (in Program Mode) for both keypads.
Specifications
Loop Characteristics
Current & Voltage Ratings
Alarm Output --------------------------------- Burg:
Fire:
12 VDC, 2A (max.)
12 VDC, 65 mA
Output Current Limiting -------------------- Burg/Fire:
AUX Power:
2.25 A
750 mA
Residential Burglary (4 Hour Standby)
Combined Standby Current: -------------- 500 mA
Bell Output: ----------------------------------- 2 A
(Using Rechargeable 12 VDC 4 AH BATTERY, minimal requirement)
Residential Fire (24 Hour Standby)
Combined Standby Current: -------------- 120 mA
Bell Output: ----------------------------------- 95 mA§
(Using Rechargeable 12 VDC 7 AH BATTERY, minimal requirement)
§
In NFPA Household Fire Installations, only a single siren or
bell can be used on this bell circuit.
Transformer and Battery
Required Transformer: -------------------- NAPCO TRF12 OR BASLER
16.5 VAC 20VA
Required Battery: --------------------------- 12V 4 AH or 7 AH Rechargeable
Change Battery every 5 years or as required
Maximum Charging Current: ------------- 165 mA
Maximum Input Current: ------------------- 2.58 A
Loop Voltage: -------------------------------- 5 Volts
Loop Current : -------------------------------- 1.1mA
Loop Resistance: ---------------------------- 300Ω per zone (max.)
Device Specifications
Max # keypads: ------------------------------ 4, GEM-K800/GEM-RP8 current = 65 mA
Max # of receivers: -------------------------- 2, GEM-RECV-XP8
current = 65 mA each
Max # of compatible
2-wire smoke detectors : ------------------ 10
Max Keypad wire length : ---------------- 1000’ total wire length
Miscellaneous
Housing Dimensions : -------------------- 11" x 121/8" x 3"
(28 x 30.8 x 7.6) HxWxD
Shipping Weight: --------------------------- GEM-P801 5.5 lbs.
Operating Temperature: ------------------- 0-49ºC (32-120°F)
3
WI1089A GEM-P801 Installation Instructions
UL Compatible Smoke Detectors
Ordering Information
GEM-P801 Compatible Smoke Detectors (Approved by UL)
Mfg
Sentrol
4-Wire
Smoke Detector
449AT
449C
449CRT
449CST
449CSRT
449CSRH
System
Sensor
1112
2112
NAPCO
FW-4
449CSST
449CLT
449CSLT
449CTE
741U
742U
2112T
2112TSRB
2-Wire
Smoke Detector
712U
722U
732U
711U
721U
2100
2100T
721UT
731U
Smoke Detector
Base
701U
702U
702RE
702RU
1100
FW-2
GEM-K800
OI302 / OI219
WI1090
8 zone Control Panel with 2-wire Fire
(6 Hardwire/Wireless+2 wireless)
Keypad
Operating Instructions for Keypads GEM-K800 / GEM-RP8
Programming Instructions GEM-P801
Optional Accessories
FT2200
End of Line Relay/Resistor Supervisory Module
GEM-RECV-XP8:
*Wireless Receiver
GEM-TRANS2:
Window/Door Transmitter
GEM-KEYF:
Keyfob Transmitter
GEM-WP:
Wireless Waterproof Panic Button
GEM-SMK:
Wireless Smoke Detector
GEM-HEAT:
Wireless 135°F / Rate of Rise Heat Detector
GEM-PIR:
Wireless PIR
GEM-PIRPET:
§
GEM-DT:
Wireless Dual-Technology Sensor
Wireless Pet-Immune PIR
LISTINGS AND APPROVALS
GEM-GB:
Wireless Glass-Break Detector
UL HOUSEHOLD FIRE AND BURGLARY WARNING SYSTEM CONTROL UNIT
STANDARDS # 1023, 985.
RB1000:
§
Single Form C Relay Board
Veriphone:
§
Audio Verification Module
SECURITY INDUSTRY ASSOCIATION (SIA) FALSE ALARM REDUCTION STANDARD CP-01.
PCD-Windows:
§
Downloading Software for IBM Compatible PC
CALIFORNIA STATE FIRE MARSHAL (CSFM) - CONTROL UNIT (HOUSEHOLD) # 71870992:126.
VERIFIED TO COMPLY WITH F.C.C. PART 15 AS CLASS B : DIGITAL DEVICE.
EUROPEAN E.M.C. REGULATIONS CE CERTIFICATION
HARMONIZED STANDARDS: EN50081-1 AND EN50082-1
EC DIRECTIVES: 89/336/EEC, ELECTROMAGNETIC COMPATIBILITY DIRECTIVE
4
GEM-P801
Must be PCD-Windows Version 5.0 or later.
PCI2000/3000:
§
Downloading Interface for IBM Compatible PC (includes
PCL2000B Local Download cable)
PCL2000B:
Local Download cable
* Supports up to 8 zones, 4 Key Fobs, 4 Smoke Detectors
§
Not evaluated by UL.
Note: Wireless and Access Features have not been evaluated by UL. Note: No
unattended downloading is allowed by UL.
Programming the Panel
Refer to GEM-P801 Programming Instructions (WI1090).
The GEM-P801 is factory programmed with all features required by the SIA False Alarm Reduction
standard CP-01, and this CP-01 program can be
reloaded into the panel by defaulting the panel. In
this manual and in WI1090, the "†" symbol indicates
the features that exist in the panel that are specifically required by CP-01.
Note: The communicator features are enabled but
require a telephone number, account number, correct reporting format and report codes (if required by
the format) or the panel will generate a "fail to communicate" trouble. If the panel is intended for local
use, only remove the 1 from programming location
[45-1] to disable the communicator.
Downloading
The GEM-P801 panel can be download/uploaded
with PCD-Windows Version 5.0 (or later) software
using the Ring Method, Answering Machine
Override (Second Call) or the Keypad Connect
R6 method of downloading. The panel can
also be automatically downloaded/uploaded using
the PCPreset utilty. For Site Initiated Downloaded,
see Auto Download ID Number [93].
Note: Any programming in Dealer Options 1 [96] and Dealer
Options 2 [97] will not be defaulted. If Dealer Code Lockout has
been programmed the panel will not default the Dealer Code.
Note: Unattended downloading from a computer is not
allowed for Fire Alarm or UL installations.
Local Downloading
Wire as shown in Figure 1. Use the power up or
R6 method of establishing a connection. The
power up method is recommended if the panel is attempting
to report.
TELCO JACK
RJ31X
TELCO
JACK
Defaulting the Panel
1. Remove power from the panel.
2. Remove all wiring from terminal 19 (PGM) and
terminal 3.
3. Connect terminal 19 (PGM) to terminal 3.
4. Apply power to the GEM-P801 control panel.
5. After a few seconds the ARMED, READY and
HSYSTEM TROUBLE LEDs will flash.
6. The keypad will beep 3 times indicating the
panel default values have been loaded.
7. Turn off power and remove wiring between
terminal 19 (PGM) and terminal 3.
8. Re-install original wiring for terminal 19 (PGM)
and terminal 3 then re-apply power.
1. The Keypad Connect R6 method
2. Ring method
3. Answering Machine Override (Second Call)
4. Site-Initiated (PCPreset & R6)
5. Automatic Downloading (Using PCPreset)
GEM-P801 Panel at the site
16
17
+PWR
GND
18
19
20
TELCO
RED
BLACK
PCI2000
*RED
*GREEN
*Insulate if not used
PCL2000B
J1
J2
TO COMPUTER
TO EXTERNAL
MODEM
J3
LOCAL
TO
J5 LINE
OUT TO
J4
TELCO
MODEM
FIGUREDownloading
1 LOCAL DOWNLOAD
Remote
Wire as shown in Figure 2. The panel can be
remotely download/uploaded using any one of the
following methods:
MODEM
FIGURE 1 REMOTE DOWNLOAD
5
WI1089A GEM-P801 Installation Instructions
Installation
Mounting the Panel
Mount the Panel close to an unswitched AC
source, a cold-water pipe ground, and a
telephone line connection.
Mounting the Keypad
A keypad should be located near an exit/entry
door. To remove the keypad from the backplate,
insert a small screwdriver into the slots at the
bottom of the keypad.
Pull up on the
screwdriver to pop off the cover.
detectors should be installed in areas other than
those required, such as the dining room,
bedrooms and utility room. Heat detectors,
rather than smoke detectors, are recommended
in kitchens, attics, and garages due to
conditions that may result in false alarms and
improper operation.
Refer to NFPA Standard 74 (National Fire
Protection Association, Batterymarch Park,
Quincy, MA 02269) for additional information,
including proper mounting methods.
12 (+PWR)
BLACK
13 (GND)
GREEN
14 (GREEN)
Telephone Wiring
Wire as shown in the wiring diagram in the back
of this manual.
WARNING
The FCC restricts the use of this equipment on
certain telephone lines.
Read the FCC
statement on the back of this manual to ensure
compliance.
TABLE 1 KEYPAD W IRING
Typical Fire Installation
(Where permitted by local codes)
Install smoke detectors outside each sleeping
area and on each floor, including the basement.
Install the living room and basement smoke
detectors near the stairway of the next upper
level.
For increased protection, additional
6
Connect the control-panel EARTH GROUND
screw through a No. 16 AWG or larger wire to a
metal cold-water pipe. Do not use a gas pipe,
plastic pipe or AC ground connections. Use at
least #16 AWG wire. Connect a wire with a
ground lug crimped or soldered onto one end
and connect it to the EARTH GROUND screw in
the cabinet.
Complete all wiring before connecting the
battery or AC Power.
Do not plug the
transformer into a switched outlet.
Control Panel Terminal
RED
Grounding the Panel
AC Power and Battery Wiring
Up to 4 keypads can be connected on individual
wire runs with #22 AWG wire with a maximum
total cable length of 1000 feet. Each keypad
draws approximately 65 mA.
Keypad Wire Color
Wiring
FIGURE 3 Typical Fire Installation
Burglary Zone Wiring
Fire Zone Wiring
The GEM-P801 provides 6 true hard-wired, EndOf-Line Resistor terminated burglary zones.
Wire zones as shown in the wiring diagram (pg.
30). All resistors must be installed, even if the
zone is not used. If required, the feature No
End Of Line Resistor may be programmed, in
which case a direct short across the zone will
cause the zone to set up. (NOTE: Not for UL
applications) Program the zone as a No EOL
Resistor Zone [06].
If necessary, use the voltage chart below to
verify proper voltages. These values represent
the DC voltage of the zone while in the indicated
state with reference to the the zone’s respective
ground terminal.
Zone Normal (EOL across zone)
2.5 V
Zone shorted
0V
Zone Open
5V
TABLE 3 VOLTAGE AT TERMINALS 3&5, 6&8,
Wire the Fire Zone as shown in the Wiring
Diagram in the back of this manual. An EOL
resistor must be installed, even if the Fire Zone
is not used.
Fire Zone Normal
13.0V
Fire Trouble
13.8V
Fire
0.0 V
TABLE 4 VOLTAGE AT FIRE ZONE (Terminals
12&13)
PGM Wiring
The PGM (Terminal 19) is a switched negative
output that is activated through programming
option(s) that have been selected in
programming blocks [08], [23] - [25]. Connect
the device controlled by the PGM between
+PWR and the PGM terminal. (maximum load of
50 mA).
The PGM output is limited on the number of
features that can be programmed simultaneously, such as PGM Access.
9&11
Keypad Operation
Keypad zone LEDs indicate zone status.
ARMED, STATUS and HSYSTEM LEDs
Keypad Sounder
3 QUICK BEEPS
Panel Armed (System ON)
Chime ON
Fault Find Mode ON
Keypad Sounder ON
Zone Bypassed
6 QUICK BEEPS
Panel Disarmed (System OFF)
Chime OFF
Fault Find Mode OFF
Keypad Sounder OFF
Zone Un-Bypassed
1 SECOND - STEADY TONE
Incorrect Code Entered
Invalid key entry
4 LONG BEEPS (PRIORITY CONDITION)
1. Entering an Arm Code with a faulted zone
(Not an Auto-Bypass Reentry Zone).
2. Entering an Arm Code when the Bell or
PGM is ON (Bell and PGM will turn OFF).
3. Arming with the Fire LED ON - reset
required. Press the C key.
provide system status. The keypad sounder
provides feedback beeps for correct and
incorrect entries.
7
WI1089A GEM-P801 Installation Instructions
Panel Operation
Keypad LEDs
ARMED LED DEFINITION
Armed
Instant Mode
Zone in Alarm
STATUS LED DEFINITION
Ready to be Armed
Zone faulted
H
ON
OFF
Flashing
ON
FIRE LED DEFINITION
Fire Alarm
Fire Memory
Flashing
ON
AC LED DEFINITION
AC Present
AC Failure
ON
OFF
ZONE LED DEFINITION
Faulted Zone
Bypassed Zone
Zone in Alarm
8
ON
Rapid Flash
Flashing
TROUBLE LED DEFINITION
AC Failure
System Trouble(s)
I
Arming (System ON)
ON
Slow Flash
Flashing
Before arming the system close all protected
zones (unless programmed as Auto-Bypass
Reentry Zones). Enter a 4-digit Arm/Disarm
code, followed by the
U
key, the keypad will
provide a feedback beep for each key pressed.
If a valid Arm/Disarm code is entered, the
keypad will beep 3 times. If an incorrect Arm/
Disarm code is entered, the keypad will sound a
1-second tone indicating an incorrect entry.
Arming without Entry Delay (Instant
Mode)
When arming, press the P key to eliminate
the entry delay. The ARMED LED will flash
rapidly to indicate the panel is in Instant Mode.
If an Exit/Entry Zone is tripped while the panel is
in Instant Mode the panel will go into alarm
immediately.
Arming/Disarming with a Keyfob
The system can be armed by pressing the K
key, and disarmed by pressing the L key on
the Keyfob. Zones programmed as Exit/Entry
Follower Zones can be bypassed when the M
or N keys on the Keyfob [81-84] have been
programmed for Interior [8].
Zones
programmed as Exit/Entry Follower Zones can
be un-bypassed when the M or N keys on
the Keyfob have been programmed for Full Set
System [7]. To arm the system with all zones
protected press the K key. Press and hold
the M or N key for 2 seconds to fully set the
system (The LED on the Keyfob indicate the
Keyfob has transmitted the signal). Program
Keyfob/Keyswitch Chirp [23-4] for an audible
indication of system arming and disarming.
Arming/Disarming with a Keyswitch
The system can be armed/disarmed by using a
momentary Keyswitch [26-1] and wired to Zone
6 in series with resistor with a normally closed
switch. Program Keyfob/Keyswitch Chirp [23-4]
for an audible indication of system arming and
disarming. To convert keyswitch operation from
Normally Closed style to Normally Open,
program [27-1] Keyswitch Polarity.
NOTE:
Faulted Keyswitch or silent 24 hour zone normally do not display at
the keypad. If a silent 24 hour zone or Keyswitch is faulted at the
time of arming the faulted zone will display only while the priority
sound is ON. Keyswitch Arm with No End of Line Resistor programmed; must program [06-6] No End-of-Line Resistor for Keyswitch Zone 6 and must not program [27-1] Keyswitch Polarity.
Arming Instant with a Keyfob
The panel can be ARMED INSTANT when the
[A1] or [A2] keys on the Keyfob [81-84] have
been programmed for Instant [8]. To arm the
system with Instant protection press the [ON]
key, then press and hold the [A1] or [A2] key for
2 seconds to arm the panel with INSTANT
protection.
Disarming (System OFF)
After entering the premises through an Exit/
Entry Zone, the keypad will sound the Entry
Delay Tone. Enter a valid Arm/Disarm code,
then press
U.
If a valid Arm/Disarm code is
entered, the keypad will beep 6 times, indicating
the panel has been disarmed. The red Armed
LED will go out. If an incorrect Arm/Disarm
Code is entered, the keypad will sound a 1second tone, indicating incorrect entry. Press
C and re-enter the code.
Disarming after an Alarm (Alarm Memory)
The armed LED and the zone(s) that caused the
alarm will be be flashing. Disarm the panel.
The system is currently not detecting zone faults
or displaying system trouble. The zone(s) that
caused the alarm will continue to flash. The
STATUS and HSYSTEM TRBL LEDs are out
indicating:
The system is displaying Alarm Memory.
Press C to clear Alarm Memory.
Bypassing
Automatic Bypassing
Note: Automatic Bypassing has not been
evaluated by UL
Home/Away with Delay Zones
This zone type has the following operation
depending on whether an Exit/Entry Zone has
been violated during the Exit Delay time.
Home
Exit/Entry Zone is not violated
Zones selected as Home/Away with Delay
Zones will be bypassed automatically.
Away with Delay
Exit/Entry Zone is violated
Zones selected as Home/Away with Delay
Zones will have a fixed 20-second entry
delay when violated before an Exit/Entry
Zone.
Return to FULL SET SYSTEM (no interiors bypassed) after having been Full
Set System with Home/Away with Delay
(No exit causing interiors bypassed)
From the Keypad
Press BC to return protection to
Home/Away with Delay Zones that have
been automatically bypassed.
Three
minutes are allowed to walk through and
Exit/Entry Follower Zones.
Using A Keyfob (GEM-KF)
All zones in the system can be armed
regardless of the state of the Exit/Entry
Zone when arming with a Keyfob and using
an AUX key programmed as Full Set System. Press [ON] and press and hold the
[A1] or [A2] keys for 2 seconds when leaving
the premises. All zones, including Home/
Away Zones are armed.
Bypassing a zone
Press B, then the zone number to be
bypassed. While the panel is DISARMED, the
bypassed zone LED will flash slowly; indicating
the zone has been bypassed. While the panel is
ARMED, the bypassed zones will only be
displayed if the Display Bypassed [21-3] option
has been selected.
Unbypassing a zone (Disarmed only)
Press the B key then the number of the
zone to be unbypassed.
Group Bypass (Interior Bypass)
Press the P key to Bypass all Exit/Entry
Follower Zones [02] with or without Home/
Away Zones [01].
Using A Keyfob (GEM-KF)
Hold the [A1] or [A2] key on the Keyfob to
Bypass all Exit/Entry Follower Zones [02] with
or without Home/Away Zones [01].
User Program Mode
To prevent the loss of the User 1 Code, the
panel default program includes User 1 Code
Lockout [96-2].
To change the User 1 Code from its default
value of 1234, program the 4-digit User 1 Code
through Dealer Programming [95]. User 1 Arm/
Disarm code is used to program User Codes 2 8. By default, the User 1 code cannot be reprogrammed by the user.
If it is necessary to allow the user to re-program
the User 1 code, it can be changed through
downloading or Dealer keypad programming.
9
WI1089A GEM-P801 Installation Instructions
From Dealer Program Mode, change the User 1
Code Lockout ([96-2] LED=OFF) to disabled.
Entering User Program Mode
1. Enter R8
2. Enter User 1 Code (1 2 3 4)
(Default)
3. Press D.
ARMED, STATUS AND HSYSTEM
TROUBLE LED’s WILL FLASH.
H
TA
D S
1
TUS
A 1 is displayed indicating
User 1 Code is programmed
and 2-8 are blank.
Zone LED Meaning
OFF
User Arm/Disarm Code not programmed
Flashing
User Arm/Code is currently being programmed
Steady
User Arm/Disarm Code has been programmed
TABLE 5
10
User Mode Programming Example:
1.Press 2, Zone 2 LED will Flash
2.Enter 1 9 2 3, Zone 2 LED
will continue to flash until the 4th digit is
entered. The keypad will beep 4 times
confirming a valid entry (Zone LED steady).
Deleting a User Code
GEMINI
E
ARM
While in User Program Mode the Armed, Status
and HSystem Trouble LEDs will continue to
flash, follow the example below to program User
2’s code to 1923.
ZONE LED DEFINITION-USER PROGRAM
MODE
Press the number of the User to be deleted, the
zone LED will be flashing indicating that the user
has been selected. Press the Q key, the
LED associated with the user will now be OFF.
Exiting User Program Mode
To exit User Program Mode press C.
GEM-P801 Commands
User Commands
R1
Bell Test
While disarmed, enter this command to turn on
the Bell, keypad sounder and keypad LEDs for 2
seconds. The battery is tested during a Bell
Test, and automatically every *24 hours to
ensure proper battery operation under load.
The Alarm output requires a battery in order to
supply the specified output. If the battery cannot
sustain the load, a low battery indication will be
displayed. A battery test is also performed on
power-up after a 3 minute delay.
*A battery test occurs every 4 hours when
Household Fire [96-3] has been selected.
Q Easy Arm AWAY
While disarmed, press and hold this key to arm
the panel. To disarm the panel a valid Arm/
Disarm code must be entered. Requires Easy
Exit/Easy Arm [21-2] to be enabled.
P Easy Arm STAY
While disarmed, press and hold to bypass all
Exit/Entry Follower Zones with or without Home/
Away Zones.
P Instant
Press and hold before or after arming to remove
the entry delay on Entry/Exit Zones.
The
keypad ARMED LED will flicker rapidly. Faulting
an Exit/Entry Zone will result in an immediate
alarm.
R5 Chime ON/OFF
Enter this command to turn chime ON/OFF. The
Keypad will chime on any zone that has not
been selected as an Exit/Entry Follower Zone,
Home/Away with Delay Zones, or 24 Hour Zone.
R8+User 1 Code-(User Program
Mode)
See previous section for information about entering User Program Mode.
R9
Keypad Sleep Mode ON/OFF
Enter this command to turn the keypad sounder
ON/OFF. When the keypad is in Sleep mode all
keypad sounds for this keypad will be silenced
except for keypad feedback beeps and Keypad
Sounder on Alarm.
User Commands - Optional
R0 Easy Exit
If enabled in Dealer programming, enter this
command while the panel is Armed to allow 3
minutes to exit the premises through Exit/Entry
and Exit/Entry Follower Zones. Program Easy
Arm/Easy Exit [22-2].
R3
Access on PGM
If enabled in Dealer programming, enter this
command to activate the PGM output (Terminal
19) for 5 seconds. Note: Program Access Output [23-2] cannot be programmed with other
PGM features.
Dealer Commands
R6
Keypad
Connect
Download
(Programming Required)
Establish a connection between the PCDWindows phone line and the Control Panel
phone line. When ready, tell the installer to arm,
then disarm. Then enter R6 within 4
seconds in order to establish a connection.
Phone connection to installer will go "dead" as
downloader and panel connect.
Fault Find ON/OFF
Hardwired Zone Operation
R7
Enter this command to turn Fault Find ON/OFF.
While in Fault Find mode, the loop response for
all zones will be set to the faster response of 40
ms. The keypad will beep for .25-seconds when
hardwired zones are faulted and for 1-second
when zones are restored. Keyswitch Arming
has presidence over Fault Find and will arm/
disarm the system, disabling Fault Find.
Wireless Operation (Signal Strength)
While in Fault Find mode the keypad will provide
an audible (Table 6) and visual (Figure 5)
indication of each transmitter’s signal strength.
The signal strength metering is based on a scale
of 4 to 10, with 4 being marginal and 10 being
excellent.
The keypad will beep out a number, from 1-4,
corresponding to the signal strength of the
transmitter. See Table 6. Each beep is 1second long. The keypad will sound a short
beep for transmitters with signal strengths of 3
or less.
SIGNAL STRENGTH
3 or less
4
5
6-7
8-10
KEYPAD SOUNDER
.25S BEEP
BEEP
BEEP BEEP
BEEP BEEP BEEP
BEEP BEEP BEEP BEEP
TABLE 6 AUDIBLE SIGNAL STRENGTH INDICATION
1
Signal Strength = 4
1 2
Signal Strength = 5
1 2 3
Signal Strength = 6-7
1 2 3 4
Signal Strength = 8-10
FIGURE 5 VISUAL SIGNAL STRENGTH INDICATION
Signal Strength Logging Mode
The Signal Strength Logging Mode is a
troubleshooting tool which allows the collection
of signal strength information for all transmitters
on the system. Normally the Signal Strength of
Supervisory Signals are not logged; during
Signal Strength Logging Mode the signal
strength information for all supervisory signals
received over a two hour period will be saved to
the LOG.
Local Activation
Enable [92-4=ON], this will initiate a two hour
11
WI1089A GEM-P801 Installation Instructions
test period where all supervisory signals will log
signal strength information.
•
Remote Activation
•
Using PCD-Windows V5.0 Software, follow
the instructions below:
From the Status Screen:
Select [ Enable Signal Strength Logging ]
The Signal Strength logging mode will
automatically time out in 2 hours.
Uploading Signal Strength Information
from the Log
After approximately (2) two hours, re-establish a
connection with the panel. Signal strength log
information ranges from 1 to 10. The logging of
signal strength should appear similar to the
sample LOG below:
7/24/2005 08:44AM
7/23/2005 07:43AM
7/22/2005 06:44AM
QL: Establish Connection
(Callback) Operator 0
Transmitter Status: Zone
7(7) SS 10 1
Transmitter Status: Zone
7(7) SS 10 1
TEST MODE
This is a dealer option, only used to test the
system after installation. To enter Test Mode,
enter 4-digit Dealer Code, press R, then
press 1.
•
Initiating test mode causes bell test and
“Start Test Mode Report” (FD or Point ID
•
•
•
•
•
•
•
607) to Central Station.**
Red LED and Green LED slowly flash,
indicating “SIA Test Mode”.
All faulted zones are memorized and displayed.
All zones set to Auto Reset.
No arming or alarm reporting to Central
Station allowed during test mode.
Time-out in 20 minutes, or press [RESET]
to exit.
Five minutes prior to 20 minute time-out,
Red and Green LEDs flash slower.
Sends “End Test Mode Report” to Central
Station when the mode is exited or timedout (FE or Point ID 607).**
If 24-hour zone is faulted at end of test, a
Zone Trouble for that zone is generated.
If backup reporting is selected, Telco T1
will be used for "Start Test Mode", Telco T2
will be used for "End Test Mode".
**Address [45-1] Communicator Enabled must
be set for "Start Test Mode" and "End Test
Mode" to report.
Zone Features
†[00]Exit/Entry Zones
Delay allows exit and entry through an Exit/
Entry Zone after the system is armed
without setting off an immediate alarm. Exit
Delay allows the user to leave the premises
after arming. Entry Delay allows the user
The "†" symbol indicates features that are specifically required by SIA CP-01.
12
time to enter and disarm. The entry delay
may be canceled by pressing F.
[01]Home/Away with Delay Zones
Zones that automatically bypass at the
expiration of the exit delay if the EXIT/
ENTRY zone(s) are not violated. Zones of
this type have a three (3) minute power-up
delay,
and do not display or cause an
alarm if faulted when the system powers up.
Pressing the C key cancels the 3 minute
timer.
If Exit/Entry zone(s) are violated during the
exit delay, zones programmed as Home/
Away with Delay Zone(s) will have a fixed
30-second entry delay, if violated before the
Exit/Entry zone.
To eliminate this fixed 20-second entry
delay, also program zones as Exit/Entry
Follower Zones [02].
To return protection to zones of this type,
press BC from the keypad or [A1] or
[A2] from a Keyfob. Program the Keyfob
[81-84] AUX 1 or AUX 2 button(s) for Full
Set System [enter 7 in AUX 1 or AUX 2 in
Program Mode].
NOTE:
If R0 is Entered during Exit Time, Home/Away with
Delay Zones will be automatically bypassed, even if the
Exit/Entry Zone is violated. Easy Exit/Easy Arm [22-2] must
be enabled.
[02]Exit/Entry Follower Zones
Entry Delay allows the user time to enter
and disarm. Allows exit after the panel is
armed without setting off an immediate
alarm and allows entry only if an Exit/Entry
Zone [00] has been violated first. Zones of
this type have a three (3) minute power-up
delay, and do not display or cause an alarm
if faulted when the system powers up.
Pressing the C key cancels the 3 minute
timer.
Group Bypassing (Interiors Bypassing) Zones programmed as Exit/Entry Follower
Zones will be Group bypassed if the P
key is pressed while disarmed or within the
Exit Delay.
Auto Interior Bypassing - Also program
zones as Home/Away with Delay Zone(s)
[01] to automatically bypass at the expiration
of the exit delay if the EXIT/ENTRY Zone(s)
are not violated during the exit delay.
[03]Auto-Bypass Reentry Zones
Zones programmed as this zone type are
permitted to be faulted at the time of arming.
Once the zone is restored, while the control
panel is still arming or has been armed, the
zone will automatically be unbypassed and
any subsequent violations of the zone will
cause an alarm condition. (Not Evaluated
by UL).
[04]24-Hour Protection
A zone that provides protection at all times,
whether or not the system is armed.
[05]40 ms Loop Response
Normally loop response is 750 ms, select
this option to change the loop response to
40 ms. The slower the loop response, the
less sensitive the system will be to
intermittents (swingers). The programming
option is not permitted for UL installations.
[06]Disable EOL Resistor
Program this zone type if an End Of Line
Resistor is not required on the zone(s). If
programmed, a direct short across the zone
is the normal condition, while open is
faulted.
This programming option is not permitted for
UL installations.
†[07]Burg (Steady) Output
Enables the Bell Output on a zone trip for
each zone selected. The Bell Output will
remain ON for the length of time
programmed for Burg (Steady) Output [07]
or it will remain ON until turned off by
entering a valid Arm/Disarm Code; 0 means
output will stay ON until turned off.
[08]PGM Output
The PGM output is a negative trigger output
which may be used to drive an LED, low
current (<50mA) relay or to trigger an input
to a long range radio. [08] enables the PGM
Output on a zone trip for each zone
selected. The PGM Output will remain ON
until reset.
[09]Selective Bypass
If programmed, selected zones will be able
to be bypassed by the User. By default, all
zones are permitted to be bypassed.
System Times
[10]Exit Delay
The delay time which permits exit through
an Exit/Entry Zone [00] after the system is
armed, allows a user to leave the premises
without setting off an immediate alarm. Exit
Delay may be programmed for up to 255
seconds (4¼ minutes); a value of 0 will
default to 45 seconds for CP-01 and 15 seconds for non CP-01. SIA CP-01 Required
Default = 60 seconds.
[11]Entry Delay
Delay time permits entry through Exit/Entry
Zone(s) after the system is armed without
setting off an immediate alarm. Entry Delay
allows the user time to enter and disarm the
system. Upon entering, the keypad sounder
will sound a steady tone (Entry Sound) to
remind the user to disarm the system.
Entry Delay Time [11] may be programmed
from 30 to 255 seconds (4¼ minutes); a
value of 0 defaults to 30 seconds. Entry
Delay may be canceled by pressing and
holding P before or after arming. SIA
CP-01 Required Default = 30 seconds.
The "†" symbol indicates features that are specifically required by SIA CP-01.
13
WI1089A GEM-P801 Installation Instructions
[12]Burg (Steady) Output Time-out
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
UL required minimum = 5 minutes.
[13]Fire (Pulsed/Temporal) Output T/O
Can be programmed from 1 to 255 min (4¼
hours); 0 for output active until silenced by
entering an Arm/Disarm Code. For temporal
sounder, enable [96-3] UL Household Fire.
UL required minimum = 5 minutes.
[14]Test Timer Interval
Test Timer
If Test Timer [36-4] is enabled, program the
interval, in days, between Test Timer
reports. Valid entries are from 1 to 255 days.
[15]Line Cut Time-to-Fail
Enable this feature by programming the
delay time required to declare a line cut
failure. Programming 000 will disable line
cut detection.
[16]Wireless Supervisory Timer
A transmitter will send a transmission every
time it is tripped; when there is no activity,
the transmitter sends a supervisory
transmission about once an hour. If the
receiver does not receive any signal (either
a trip or a status) from a transmitter in the
14
time specified, a system trouble ‘RF
Supervisory Failure' will be indicated at the
keypad. Timer is programmable from 1-26
hours; 0 means NO supervision.
[17]Wireless Smoke Supervisory Timer
A smoke detector will send a transmission
every time it is tripped; when there is NO
activity, the smoke detector sends a
supervisory transmission about once an
hour. If the receiver does not receive a
signal (either a trip or a status) from a
transmitter in the time specified, a system
trouble ‘RF Supervisory Failure' will be
indicated at the keypad. The Supervisory
timer is programmable from 1-8 hours; 0
means NO supervision. Note: If UL
Household Fire is enabled, the Wireless
Smoke Supervisory Timer will automatically
be set to 4 hours.
[18]Test Timer Offset
Enter the time, in hours, that a Test Timer
will be reported after Dealer Mode has been
exited. With the default value of 12, the test
timer will be sent 12 hours after exiting
Dealer Mode. The test timer can also be
offset using PCD-Windows Downloading
Software. On power up the test timer is sent
immediately. Follow the commands below
to offset the test timer using Quickloader
Software:
1. From the Status Screen, select
Miscellaneous
2. Enter the number of hours for Test
Timer Offset
3. Select Set Test Timer Offset
4. Select OK
System Features
[20]Keypad Features 1
(1) Enable Keypad Fire (7G)
Additional Programming required:
Select reporting to Telco 1 [36-1] or Telco 3
[56-1].
(2) Enable Keypad AUX (8G)
Additional Programming required:
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
(3) Enable Keypad Panic (9G)
Additional Programming required:
Select reporting to Telco 1 [36-3] or Telco 3
[56-3].
(4) Enable Ambush - If enabled, the 8th
User Code will send an Ambush report
when entered to disarm the system.
Additional Programming required:
--Program User 8 Arm/Disarm Code.
--Select reporting to Telco 1 [36-2] or Telco
3 [56-2].
UL Installations: If Keypad Fire [20-1] is
enabled, the keypad must be mounted
within (3) three feet from the Control Panel
with no intervening barrier, such as a wall or
a ceiling.
[21]Keypad Features 2
(1) Audible Panic - Keypad Panic will not
turn the Bell on unless this option is
programmed.
†(2) Exit/Entry with Urgency - select to give
an audible indication of Exit and Entry times.
During the last 10 seconds of entry and exit
time, the keypad sounds a distinct sound to
indicate you must either leave the premises
or the panel must be disarmed.
(3) Display Bypassed (Armed) - Select to
display bypassed zones while the panel is
armed.
(4) Disable Code Entry Beeps - Disabling
will turn off the keypad. Correct and incorrect code entry beeps, except while in
Dealer Program Mode (i.e. no indication of
incorrect code entry).
[22]Miscellaneous Features 1
(3) Swinger Shutdown - Automatically
disables armed zones with excessive alarm/
restores (swingers).
Non-24-Hour
Protection zones: allows only 3 alarms and
2 restores per zone per arming before the
zone is disabled if [80] is not programmed.
See page 24 for more information.
(4) Bell on Line Cut (Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed. Program Line Out Time [15] with a value of 10255 seconds (000 = disable).
[23]Programmable Output Features 1
(1) Audio Verification - Program to activate
the PGM during reporting. Select specific
zones for audio verification by programming
the required zones in PGM Output [08],
PGM Features 2 [24] and PGM Features 3
[25]. Connect the PGM to the VeriphoneTM
trigger low input.
(1) Dialer (Abort) Delay - Program to allow
a 15 second Delay (except 24 Hour Zones)
after a zone trip before reporting. Disarm
the system within 30 seconds to prevent
reporting if [79] not programmed.
(2) Easy Exit/Easy Arm- Enables
R0 command. While the system is
armed, entering this command allows 3
minutes to Exit through Exit/Entry and Exit/
Entry Follower Zones. Enabling this option
(2) Access Output - Activates the PGM
output for 5 seconds using the R3
command. This programming option has
not been evaluated by UL.
U key to
(4) Keyfob/Keyswitch Chirp - Program to
chirp the Bell Output when the system is
armed or disarm by a GEM-KEYF KeyFob or
also enables Easy Arm, press the
arm the system.
(3) Follow Keypad Sounder - The following
keypad sounds will activate the PGM output:
Entry Sounder, Keypad Pulsing Sounder,
Keypad Output on Alarm, Chime, Fault Find.
by keyswitch. It will chirp the bell output (1)
one time when the panel is armed or (2) two
times when the panel is disarmed. Enabled
by default. (SIA CP-01 Requirement).
[24]Programmable Output Features 2
(1) Fire - Program to activate the PGM on a
Fire alarm.
(2) AUX - Program to activate the PGM on a
AUX alarm.
(3) Panic - Program to activate the PGM on
a Panic alarm.
(4) Test Timer - Program to activate the
PGM during a Test Timer report.
[25]Programmable Output Features 3
(1) AC Fail - Program to activate the PGM
on the loss of AC. (15 minute delay)
(2) Low Battery - Program to activate the
PGM on a Low Battery condition.
(3) *Trouble - Program to activate the PGM
on a Trouble condition.
(4) Armed - Program to activate the PGM
when the panel is Armed. The PGM output
will flash when the panel has gone into
alarm.
*Includes Bell Cut, Fire Trouble, Receiver Fail-toRespond, Receiver Tamper, Receiver JAM, Wireless
Transmitter Low Battery, Wireless Supervisory Failure,
Wireless Smoke Low Battery, Wireless Smoke
Supervisory Failure, and Wireless Tamper.
[26]Miscellaneous Features 2
(1) Momentary Keyswitch Arming - For
Keyswitch Arm/Disarm, connect a normally-
The "†" symbol indicates features that are specifically required by SIA CP-01.
15
WI1089A GEM-P801 Installation Instructions
closed momentary Keyswitch in series with
Zone 6 zone AND its 2.2K EOLR. See Keyswitch Polarity [27].
(2) Reserved
(3) Inhibit Fail-to-Communicate Display This option prevents the keypad from either
indicating or sounding when a Fail to
Communicate has occurred.
(4) Inhibit Low Battery Display - Program
to inhibit the Low Battery Display at the
keypad.
Low Battery Reporting is not
inhibited. The programming option is not
permitted for UL installations.
[27]Keyswitch Polarity
(1) Keyswitch Polarity - program to convert
keyswitch operation from Normally Closed
style to Normally Open wired across a 2.2K
EOLR.
[29]Programmable Chime Time
(1) Chime Time - Program chime in 1/4
second increments. For 1 second, program
4, for 2 seconds, program 8, etc.. Valid
entries are 2 - 9, and 0 defaults to 1 second.
Telephone 1 Programming
[30]Subscriber ID Number
For 4/2 format enter a 4 digit number. If 3/1
format is required, enter a 3 digit number,
then press the Q key to blank the last
digit.
[31]Telephone Number 1
Program the phone number to be dialed for
Telephone Number 1. Program the number
directly, just as it is entered on a TouchTone
phone. If 1st location is not D, E or F, then a
4-second delay occurs, prior to dialing the 1st
digit.
Use the Q key to blank out
remaining digits in the phone number.
[32]Receiver Format
Select the receiver format to be used to
report for Telephone Number 1: Program a
0 to disable reporting to Telco 1.
[0] Disabled
[1] Ademco Slow
[2] Radionics Slow
[3] Silent Knight Fast
[4] Universal High Speed
[5] Reserved
[6] Point ID
[7] Pager
[33]Receiver Options
(1) 2300 Hz HS/Kissoff - Select 2300 Hz
Handshake and Kissoff.
(2) Sumcheck - Only used for the following
Receiver Formats: Ademco Slow, Radionics
Fast, Silent Knight Fast and Universal High
Speed. This is a sophisticated data format
used to enhance the speed and check the
accuracy of the received transmission. This
format should be used whenever the central
station has this capability.
Instead of
sending a second round to verify correct
data, the panel sends a Sumcheck digit after
sending the Subscriber ID and Alarm Code.
(3) Single Digit - 3/1 Format. 3-digit
Subscriber ID number and a 1-digit Alarm
Code will be transmitted.
The "†" symbol indicates features that are specifically required by SIA CP-01.
16
(4) No Handshake - (All receiver formats
except Pager Format)
If programmed no Handshake/Kissoff is
required by the panel.
†[34]Zone Report, Telco 1
Select zone(s) required to send an alarm
report to Telephone Number 1.
[35]Zone Restore Report, Telco 1
Select zone(s) required to send a restore
report to Telephone Number 1. The zones
will send a restore after Bell time-out, unless
programmed as silent zones.
[36]System Reporting, Telco 1
(1) Keypad Fire - Program to activate a
Keypad Fire report (7G). Requires
[20-1] to be programmed.
(2) AUX/AMBUSH - Program to activate an
AUX or AMBUSH report (8G). Requires [20-2] to be programmed.
(3) Panic - Program to activate a Panic
report (9G). Requires [20-3] to be
programmed.
(4) Test Timer - Program to activate a Test
Timer report. Requires [20-4] to be programmed.
[37]System Reporting, Telco 1
(1) AC Fail Report - Program to activate an
AC Fail report (15 minute fixed report delay).
(2) Low Battery Report - Program to
activate a Low Battery report.
(3) Trouble Report - Program to activate a
Trouble report. (See Note A, below).
(4) Fire Report - Program to activate a Fire report.
[38]System Restore Report, Telco 1
(1) AC Restore - Program to activate an AC
Restore report.
(2) Battery Restore - Program to activate a
Battery Restore report.
(3) Trouble Restore - Program to activate a
Trouble Restore report. (See Note A, below).
(4) Fire Restore - Program to activate a Fire
Restore report.
Note A:
(Applies to [37-3] and [38-3]):
Includes Bell Cut, Fire Trouble, Receiver Failto-Respond, Receiver Tamper, Receiver JAM,
Wireless Transmitter Low Battery, Wireless
Supervisory Failure, Wireless Smoke Low
Battery, Wireless Smoke Supervisory Failure,
and Wireless Tamper. Contact ID format will
report trouble(s) by device and ID number.
[39]Opening/Closing Report, Telco 1
Select users required to send opening and
closing reports to Telephone Number 1.
Do not program for users that are intended
to send a Cancel Code or Conditional
Closing reports.
Backup Telephone Programming
[40]Subscriber ID Number (Telco 2)
For 4/2 format enter a 4 digit number. If 3/1
format is required enter a 3 digit number
then press the Q key.
[41]Telephone Number 2
Program the phone number to be dialed for
Telephone Number 2. If 1st location is not D,
E or F, then a 4-second delay occurs, prior
to dialing the 1st digit.
(2) DTMF with Rotary Backup - The first
attempt to communicate is dialed using the
TouchTone method of dialing, subsequent
attempts are dialed using the pulse method
of dialing. Disable this feature to dial using
only rotary dialing.
(3) DTMF only - All attempts to
communicate dial using the TouchTone
method of dialing.
(4) Backup Reporting to Telco 2 - After 2
attempts are made to communicate to Telco 1
the backup phone number is dialed (Telco 2).
[46]Communicator Features 2
[42]Receiver Format (Telco 2)
Select the format that will be used to report
for Telco 2 (Backup reporting). Refer to
section [32].
[43]Receiver Options (Telco 2)
Refer to section [33] Receiver Options.
[44]Dialing Prefix
Dialing prefix for Telco 1, Telco 2, and Telco
3. Program if using an Outside access
number. If the 1st digit is not D, E, or F,
then a fixed 4 second delay occurs prior to
dialing the first digit.
[45]Communicator Features 1
†(1) Communicator Enabled - Program to
enable the communicator.
(1) Enable Call Waiting Disable - Default is
disabled. If this feature is enabled, the first
attempt will dial "*70" prior to the telephone
number (disabling the call waiting tone during
the alarm transmission). If the first call does
not get through, subsequent attempts will dial
as programmed.
(2) 2:1 Rotary Dialing - Changes the make
break ratio when rotary dialing from 1.5:1 to 2:1.
(3) Backup if < 4 attempts - If Backup
Reporting [45-4] has been enabled, the
communicator will use Telephone Number 2
[41] for the remaining retries when there are
less than 4 retries remaining.
(4) Don't Clear Fail to Communicate
Program to prevent a good line cut test from
clearing a Failure to Communicate system
The "†" symbol indicates features that are specifically required by SIA CP-01.
17
WI1089A GEM-P801 Installation Instructions
trouble. If programmed, only a successful
communication to Central Station will clear a
Failure to Communicate system trouble.
Pager Programming
If Pager Format ([32]and/or[42]and/or[52] = 7)
is selected, pager data will be displayed as
shown in Figure 8 (on next page). If Pager
Format is selected 4/2 format must be
programmed and Sumcheck is not permitted.
If a PIN number is required refer to Leading
Digits [47].
000 033-1234
Leading Digits
Report Code
Subscriber ID Number
FIGURE 8 DEFAULT PAGER DISPLAY
Pager Alarm data is the same as 4/2 format with
the exception that the 2 digit Report Code is
transmitted before the 4 digit Subscriber ID.
NOTE:
Digits in Report Codes and subscriber IDs that are
programmed with "B" through "F" will be converted to "0"s.
[47]Leading Digits
Pager PIN Number - If a PIN number is
required by the paging system, program the
PIN number in the Leading Digits location.
See sample program below.
If a 7-digit PIN number is required, program
the panel as follows:
[31]/[41]/[51] - Pager Telephone number
[32]/[42]/[52] - Select Pager Format
[47] - X X X X X X X C
7-digit PIN Number
Terminating Digit (#)
Leading and Trailing digits can be letters B,
C or D. B = the * button on a telephone, C =
the # button on a telephone, D = 2 second
delay.
[48]Trailing Digits
Transmitted after alarm data. Refer to
section [47] for programming information.
[49]Pager Options
(1) Skip Alarm Data - Once pager format is
selected, program this option to skip alarm
data. If this option is selected, all the
programmed Leading and Trailing digits are
sent, but the event code and subscriber ID
are not transmitted.
With this option
selected, a telephone number programmed
in Leading Digits or Trailing Digits would
send the telephone number to the pager
each time a report is sent.
(2) Reserved
(3) Reserved
(4) Reserved
Telephone 3 Programming
[50] - [59]
Programming is the same as for Telco 1.
Program to split/double report to Telco 3.
Refer to sections [30] through [39].
Report Codes
[60]Zone Report Codes
Report Code for Zones 1 through 8.
4/2 format - The Zone Report Code is the
1st digit of the report code sent, the second
digit is the zone number of the reporting
zone. For example, if zone 2 has a report
code of 3, the report code would be 32.
3/1 format - Sends only the report Code
and does not append it with the zone
number.
[61]Point ID Report Codes
Point ID Report Codes are defaulted to
Burglary for zones 1 through 8. Optionally,
Point ID codes for zones 1 through 8 can be
programmed as follows:
[1] Fire
[2] Panic
[3] Burglary
[4] Holdup
[5] General Alarm
[6] Reserved
[7] Gas Alarm
[8] Heat Alarm
[9] Reserved
[A] Auxiliary
[B] 24 Hour
[62]Zone Codes
[62-1] Restore code - Zones 1 through 8.
18
The second digit of the restore code is the
zone number of the restored zone. For
example, if the Zone Restore Code [62] is
programmed to E, the restore code for that
zone would be E4 (4/2 format).
[62-2] Trouble Code - Conditional Closing
Reports. Zones that are bypassed at the
time of arming send this code along with the
zone number of the bypassed zone(s). For
example a conditional closing by User 2,
with zones 2 and 3 bypassed would be as
follows:
1234
C2
F2
F3
[63]System Report Codes
Program a 2-digit report code for Keypad
Fire, Keypad AUX, Keypad Panic, Test
Timer, AC Fail, Low Battery, Trouble* and
Fire.
*Includes Bell Cut, Fire Trouble, Receiver Fail-toRespond, Receiver Tamper, Receiver JAM, Wireless
Transmitter Low Battery, Wireless Supervisory
Failure, Wireless Smoke Low Battery, Wireless
Smoke Supervisory Failure, and Wireless Tamper.
[64]System Restore Code
The code sent when a system condition
restores. The second digit of the 2-digit
restore code is the second digit of the
System Report Code [63]. For example, if a
Low Battery System Report Code is F8 the
Battery Restore would be E8 (4/2 format).
[65]Opening and Closing Codes
Program Opening and Closing Codes for
Users 1 through 8. The second digit of the
report code is the number of the user that
armed or disarmed the system.
For
example, if the Closing Code [65] is
programmed
with a C, the closing code for User 2 would
be C2 (4/2 format).
[66]Ambush Report Code
Program a 2-digit report code for Ambush.
To send an ambush report, program a User
Code for User 8, Program report User 8 as
Ambush [20-4] and Select reporting for
Telco 1 [36-2] and/or Telco 3 [56-2].
Enhanced Communicator
Features
†[67]Telephone Number 1
(1) Send Cancel Report - Default is enabled.
When enabled, will allow a 5 minute window
during which a Cancel Report (Contact ID
code 406-00X) will be transmitted should the
system be disarmed during this time. This 5
minute cancel window starts at the end of the
abort timeout if the abort feature is enabled;
otherwise the 5 minute timeout starts immediately upon the alarm. Only non 24-hour zones
start the Abort delay and Cancel report timers.
(2) Conditional Closing Telephone 1 When enabled, all users that are not
selected to report an Opening/Closing ([39],
[59]) will report a Closing only when zones
have been bypassed. The Zone Trouble
Code [62-2] is used to report zones that
have been bypassed at the time of the
closing report.
(3) Reserved
(4) Reserved
[68]Telephone Number 3
(1) Opening after Alarm (Cancel Code) see [67-1].
(2) Conditional Closing Telco 3 - see [67-1].
(3) Reserved
(4) Reserved
[69]Miscellaneous Features 4
(1) Reserved
(2) Reserved
(3) CHIME disabled on Power Up - All perimeter zones will not chime on fault. Keypad,
if used, will allow toggling chime on/off.
(4) Fire Alarm Verification - Default is disabled. If this feature is enabled, the first trip of
a smoke detector will not generate an alarm.
The "†" symbol indicates features that are specifically required by SIA CP-01.
19
WI1089A GEM-P801 Installation Instructions
The panel will remove power from the smoke
detector for 14 seconds, allow the smoke detector to reset for 6 seconds, then wait for another trip for 60 seconds. Only if another trip is
sensed within the 60 seconds will the system
generate a fire alarm.
SIA CP-01 /Misc. Features
[70]SIA CP-01 / Misc. Features
†(1) Exit Restart Enabled - Default is enabled. When enabled, exit delay will be restarted if an egress door is opened, closed
then re-opened. This will occur only once per
arming period.
†(2) Convert Away to Stay if No Exit - Default is enabled. The system arms in the Stay
mode if the exit delay expires and no exit has
been made.
(3) Bell Chirp on All Arming and Closing
Ringback - Default is disabled. If enabled, the
bell will chirp 8 seconds after arming and it will
chirp a second time after the Central Station
has acknowledged the receipt of the closing
report.
(4) Zone 6 as Auxiliary Zone - Default is
disabled. If enabled, Zone 6 will act as follows:
24 Hour zone, short on Zone causes alarm
with pulsing bell, 1 second on, 1 second off.
Open causes zone trouble. Alarm time-out
The "†" symbol indicates features that are specifically required by SIA CP-01.
20
follows Fire time-out unless feature [70-3] is
enabled.
†[79]Abort Delay By Zone Mask
All 8 Zones enabled by default.
†[80]Swinger Shutdown (by zone)
All 8 Zones enabled by default. Each Swinger
Shutdown bit must be disabled individually.
This feature only allows one trip per arming
period when [96-4] is enabled, otherwise will
perform 3 trips. The panel must be disarmed
then rearmed for a burglary zone to generate
an alarm again. Note: Must not be disabled in
SIA CP-01 installations. See page 24 for more
information.
[89]Cross Zoning (by zone)
All 8 Zones disabled by default. Each Cross
Zoning (Zone ANDing) bit must be enabled
individually. Requires two zones in mask to trip
within 90 seconds of each other before an
alarm transmission sequence (alarm report) is
sent to Central Station. Note: If Swinger Shutdown [80] is enabled, only 1 trip per Group per
arming period will occur.
Wireless
Up to two receivers can be wired to the
GEM-P801. Each wireless transmitter can
be mapped to a zone. Only 1 wireless
device is permitted per zone, however, the
use of both hardwired and wireless on a
zone is permitted.
To Map a transmitter to a zone:
1.Enter the Programming Block Number
that the transmitter is to be mapped to.
2.Enter the 7-digit RF ID number directly,
just as it is shown on the device label.
After the 7th digit is entered the keypad
will beep.
A transmitter will send a transmission every
time it is tripped. The transmitter also sends
a supervisory transmission about once
every hour. If the receiver does not receive
a signal from a transmitter in the time
programmed in Wireless Supervisory Timer,
a system trouble ’RF Supervisory Failure'
will be indicated at the keypad.
Program Wireless Supervisory Timer [16] to
change the supervisory time from the default
of 12 hours.
The Signal strength of a transmitter can be
checked at the keypad (see A7
Fault Find Mode) or saved to the LOG (see
Signal Strength Logging Mode - pg. 11).
[71-78] Wireless Transmitters
Enter the RF ID# and the point number that
is to be mapped to the zone.
Programming Example
Map point 1 of a window door transmitter
with an RF ID# of 0012B0:0 to Zone 3.
1. Enter Dealer Mode.
2. Enter C (beeps)73(beeps)
3. Enter 12G200
Enter 1 (beeps)
Note: If the RF ID# in step 3 is not entered
correctly the keypad will emit a 1 second
tone indicating incorrect entry.
Repeat
steps 2 - 4 above.
[81] - [84] Wireless Keyfobs
The GEM-KF is a hand held wireless
transmitter capable of Arming and
Disarming the control panel and/or
activating 2 Auxiliary Functions. To activate
the auxiliary functions, press and hold the
[A1] or [A2] key for 2 seconds (see WI752
for more information). Enter the RF ID# and
AUX 1 and AUX 2 options for each Keyfob.
AUX 1 & AUX 2
Programming Options:
1 Panic
Program a 1 in the AUX 1 and/or AUX 2
option to initiate a panic alarm when the [A1]
or [A2] buttons on the Keyfob are pressed.
Additional programming required:
Keypad Panic (9G) [20-3]
Panic Report to Telco 1[36-2] and/or Telco 3
[56-3].
Audible Panic (Optional) [21-1]
2 AUX
Program a 2 in the AUX 1 and/or AUX 2
option to initiate a AUX alarm when the [A1]
or [A2] buttons on the Keyfob are pressed.
Additional programming required:
Keypad AUX (8G) [20-2]
AUX Report to Telco 1[36-2] and/or Telco 3
[56-2].
3 Bell ON
Program a 3 in the AUX 1 and/or AUX 2
option to turn the Bell ON when the [A1] or
[A2] buttons on the Keyfob are pressed.
Press the [OFF] button to turn the Bell OFF.
4 PGM
Program a 4 in the AUX 1 and/or AUX 2
option to activate the PGM Output when the
[A1] or [A2] buttons on the Keyfob are
pressed. Press the [OFF] button to turn the
PGM Output OFF.
5 Instant
Program a 5 in the AUX 1 and/or AUX 2
option to activate Instant Mode when the
[A1] or [A2] buttons on the Keyfob are
pressed.
6 Access on PGM
Program a 6 in the AUX 1 and/or AUX 2
option to activate the PGM Output for 5
seconds when the [A1] or [A2] buttons on
the Keyfob are pressed.
Addition programming required:
Enable Access Output [23-2]
7 Full Set System
Program a 7 in the AUX 1 and/or AUX 2
option to Fully Set the System when the
[ON] and the [A1] or [A2] buttons on the
Keyfob are pressed---or---when the [A1] or
[A2] buttons are pressed when the system is
armed, and Exit/Entry Follower Zones are
bypassed (with or without Home/Away with
Delay Zones bypassed).
8 Interior Bypass
Program an 8 in the AUX 1 and/or AUX 2
option to Bypass Exit/Entry Follower Zones
when the [A1] or [A2] buttons on the Keyfob
are pressed.
Only if the system is
programmed exclusively for Home/Away
with Delay Zones (with Exit/Entry follower
zones) do they get bypassed.
[85] - [88] Wireless Smoke Detectors
Enter the RF ID# of the smoke detector.
A wireless smoke detector sends a
supervisory transmission about once every
hour. If the receiver does not receive a
signal from a transmitter in the time
programmed in W ireless Smoke
Supervisory Timer, a system trouble ‘RF
Smoke Supervisory Failure' will be indicated
on the keypad.
21
WI1089A GEM-P801 Installation Instructions
Program Wireless Smoke Supervisory Timer
[17] to change the time from the default time
of 8 hours. Refer to Household Fire [96-3].
Note: Mark Smoke Detectors (Smoke 1
through Smoke 4) in order to identify them in
the event of a supervisory or battery failure.
If Household Fire [96-4] is selected,
Wireless Smoke Supervisory Time is fixed
at 4 hours.
(3) Function 6 Download - Select to enable
the keypad connect R6 method of
downloading (pg. 5).
(4) Signal Strength Test Mode - Program
to initiate a 2 hour test period. The signal
strength information for all supervisory
signals received over a two hour period will
be saved to the LOG.
[93]Auto Download ID Number
Downloading
[90]Callback Telephone Number
Program the phone number of the
downloading computer to be dialed by the
panel during a high security download.
[91]Ring Count
Program the number of rings before the
panel will pickup.
Ring Method [92-1]
(Downloading Features) must also be
selected.
[92]Downloading Features
(1) Ring Method - Enable the ring method
of downloading. The panel will pick-up on
the number of rings programmed in Ring
Count [91].
(2) Answering Machine Override - Using
second call, call the panel. The panel will
pick-up on the first ring, hang up and redial.
22
Enter the Number that is used by PCPreset
when downloading using Site Initiated Auto
Downloading (R6).
The requirements for Site Initiated Auto
Downloading are as follows:
1. Download Computer running PCPreset.
2. Program the telephone number of the
Download Computer in location [90]
Callback Telephone Number.
3. Program location [93] with the number
of the PCPreset account that is to be
downloaded.
PCPreset
1. Create the GEM-P801 account to be
downloaded using PCD-Windows
Quickloader Software.
2. Create a List using PCPreset.
3. Select the account by pressing t.
Select the desired account from the list
of PCD-Windows accounts available.
(The location in the list is the Auto
Download ID Number [93])
4. Tag the list by entering aD (download)
5. Enter Standby Mode by entering o.
The Computer is now in STANDBY
Site
At the site perform the following three steps:
1. Arm the panel.
2. Disarm the panel.
3. Enter R6. The panel will now
call the download computer running
PCPreset. PCPreset will answer the
call, establish a connection, and then
download the account that matches the
Auto Download ID Number [93] with the
account of the same number in the list
that PCPreset is currently running.
Dealer Programming
[94]Dealer Code
The default Dealer Code is 4567. Program
a new 4-digit Dealer Code. When the panel
is defaulted the Dealer Code will be
changed back to the default Dealer Code of
4567 only if Dealer Code Lockout [96-1]
has not been programmed. Note: All User
Codes must be 4 digits.
[95]User 1 Code
The 1st User code is a program code as
well as an Arm/Disarm code. The default
User Code is 1234. If User 1 Code Lockout
is programmed the User 1 Code cannot be
programmed from User Program Mode.
Note: All User Codes must be 4 digits.
[96]Dealer Options 1
(1) Dealer Code Lockout - Program to
prevent the Dealer Code from changing with
a panel default.
(2) User 1 Code Lockout - If programmed
the User 1 Code cannot be programmed
from User Program Mode.
(3) Household Fire - (Must be enabled in
UL installations). Activates the following UL
required features:
There is a 4 hour re-sound of wireless
Smoke Low Battery and wireless Smoke
Supervisory system troubles.
• An active System Battery test performed
every 4 hours instead of 24 hours and
Wireless Smoke Supervisory Timer is
set to 4 hours.
• Fire Bell Timing is Temporal.
• Wireless Smoke Supervisory Time is
fixed at 4 hours.
†(4) SIA CP-01 Features. Enabled by default.
When enabled, the following features take
effect:
1. The minimum allowed programmable exit
time is 45 seconds.
2. “Report and Enunciate Exit Error”/ (Exit
Error is door open at end of exit delay)
sends “CF” code for pulse formats and 374
Point ID.
3. “Report Recent Close”. If an alarm occurs
within 2 minutes at the end of exit delay,
Panel reports “FC” code for pulse formats
and 459 Point ID.
4. The minimum allowed Entry time is 30
seconds.
5. Enter Urgency Annunciation is changed
from steady sounder to steady with pulsing
off. This ensures that the mini-sounder on
alarm (steady sounder) sounds different
from enter urgency.
6. “Silence Entry Sounder on First Button
Press”. During Entry delay, pressing any
digit on the keypad stops the entry sounder
for 10 seconds.
[97]Dealer Options 2
(1) International Dialing Protocol - No
dialing if no dial tone, 60 seconds between
attempts and 4 second wait for dial tone.
(2) Invert Bell Output - Inverts the Bell
polarity and removes supervision from the
bell circuit.
(3) System Trouble Auto Restore Normally, System troubles require
acknowledgment (View System Trouble) in
order to restore. If this option is selected
troubles will restore without requiring
acknowledgment.
(4) User 1 Code-Program only - If enabled
User 1 Code will function only as the User
Program Code and will not Arm/Disarm the
panel.
Note: All programming within Programming
Blocks [96] & [97] will not change if the
panel is defaulted.
[98] Number of Re-Dials
The Number of re-dial attempts made by the
panel before indicating a Fail-toCommunicate (System Trouble 1-3).
Download-Only Features
The following Features are only changeable
through downloading:
Abort Delay Time
The programming for the Abort Window for all
non-fire zones is as follows:
Programming Range
Minimum
15 sec.
Maximum
45 sec.
Default Time
30 sec.
May Disable
By Zone or Zone Type
Note: In accordance with UL standards, the
aggregate of the Entry Delay [11] and Abort
Window [79] will not exceed 1 minute.
Abort Enunciation After Disarm
Enabled by default. If the system disarmed in
The "†" symbol indicates features that are specifically required by SIA CP-01.
23
WI1089A GEM-P801 Installation Instructions
the abort time window, the keypad chirps 6
times indicating disarm, then chirps another 6
times indicating that the report was aborted.
In PCD-Windows Quickloader download software, disable this feature by pressing the System Assignment button, select the System
Options tab, in the Miscellaneous field uncheck
Abort Annunciation
Cancel Enunciation after Disarm
Enabled by default. If a Cancel Report Code
(406-00X) was sent upon disarming, the keypad chirps 6 times indicating the system is
disarmed. The keypad then chirps 3 times
indicating a Cancel Report Code was transmitted. In PCD-Windows Quickloader download
software, disable this feature by pressing the
System Assignment button, select the System
Options tab, in the Miscellaneous field uncheck
Cancel Annunciation.
Cross Zone Audible Alarm on First Trip
Disabled by default. When enabled, first trip of
a Cross Zone will initiate the bell output, but will
not report to the Central Station unless another
Cross Zone trips within 90 seconds. If not enabled, the audible and Central Station report
will not occur unless another Cross Zone is
tripped.
Suppress Test Timer on any Report
Disabled by default. If enabled, any report
(opening, closing, alarm, etc.) will prevent the
next Test Timer report from being sent.
24
Test Timer Interval in hours
Disabled by default. If enabled, the test timer
interval changes from days to hours programmed in location [14].
Day Zone on Open by zone mask
When selected a zone will produce a system
trouble indication for trouble on a zone. The
event is logged and reported on the Trouble
Report [37-3] channel as day-zone point ID
(370). (Mercantile Panel Specification).
Pulse Bell on Alarm by zone mask
When selected, a zone will produce a pulsing bell at 1 second on 1 second off rate and
timeout based on the fire timeout selected.
This feature is provided principally for the
case zone 6 must be used for key-switch
input. (Mercantile Panel Specification).
Swinger Shutdown Definition
Swinger Shutdown and CP-01
Swinger Shutdown is a common term used in
the burglary alarm industry. It is a feature of an
alarm panel that prevents multiple false alarms
from being generated from faulty detectors (or
wiring) by limiting the number of alarms a zone
may report during a single arming period.
NAPCO has a programmable by zone feature
named Swinger Shutdown that we have made
available on our panels for many years. The
SIA False Alarm Reduction standard CP-01, to
which the panel now complies, requires "swinger
shutdown" on all non-fire zones. Unfortunately,
our programmable feature allows three trips per
arming period, which is unacceptable in CP-01
installations. To reduce confusion, the following
explains both Swinger Shutdown (NAPCO
Programming Feature) and Swinger Shutdown (CP-01 Requirement).
Swinger Shutdown [22-3] (NAPCO Programming Option Bit): Programming the
option "Swinger Shutdown" [22-3] and not
programming "Enable CP-01 Features" [964] will allow a maximum three alarms per
arming period for all non-fire zones not programmed "24 hour".
Swinger Shutdown [80-1,2,3,4,5,6,7,8]
(CP-01 Requirement/Programmable zone
mask): To meet the CP-01 standard, all
non-fire zones must be programmed for the
by zone feature "Swinger Shutdown" [80]
and "Enable CP-01 Features" [96-4]. This
will allow only one trip per arming period.
The panel factory program and panel default
program both enable this feature.
SIA CP-01 Quick Reference Chart
Address
[10] (enter 60)
[11] (enter 30)
[23-4]
[46-1] not on
[67-1]
[69-4] not on
[70-1]
[70-2]
[79-1,2,3,4,5,6,7,8]
[80-1,2,3,4,5,6,7,8]
[89-1,2,3,4,5,7,8] not on
[96-4]
(Download Only)
(Download Only)
(Download Only)
(Download Only)
Description
Exit Time 60 Seconds
Entry Time 30 Seconds
Chirp Bell On Remote (Keyfob) Arm Enabled
Disable Call Waiting
Send Cancel Report
Fire Alarm Verification
Exit Restart Enabled
Convert Away To Stay If No Exit
Abort Delay By Zone Mask
"Swinger Shutdown" (Disable Auto Reset)
Cross Zoning
CP-01 Features
Abort Delay Time Default To 30 Seconds
Abort Enunciation After Disarm
Cancel Enunciation After Disarm
Cross Zone Audible Alarm On First Trip
•
•
•
The following optional accessories support the SIA False Alarm Reduction (FAR) classification, and may be used if desired: GEM-RECV-XP8, GEM-KFOB.
•
•
Cross zoning is not recommended for Line security Installations nor is it to be implemented on exit / entry zones.
•
•
•
Do not duplicate any reporting codes. This applies for all communication formats other than SIA sending automatic programmed reporting codes.
Programming at Installation may be subordinate to other UL requirements for the intended application.
Un-vacated premises: When the system/partition is armed with AWAY button, the system will arm STAY if no exit. There must be a minimum of one Exit/
Entry Follower with or without Home/Away with Delay Zones on the partition.
There is a Communication Delay of 30 seconds in this control panel. It can be removed, or it can be increased up to 45 seconds at the option of the end user
by consulting with the Installer.
In UL installations, Entry Delay time plus Abort Delay time (total combined times) cannot exceed 60 seconds.
Exit Time Restart must be disabled for UL Line Security/Encryption applications.
25
WI1089A GEM-P801 Installation Instructions
System Troubles
Use the System Trouble chart on the following
page to determine the specific System Trouble(s).
During normal panel operation the HSYSTEM
TROUBLE LED has the following two modes of
operation:
EXAMPLE
- LOW BATTERY SYSTEM TROUBLE
Enter R4 to enter System Trouble mode
and determine the specific trouble. Press any key to
view all system troubles.
GEMINI
H
STEADY
FLASHING
1-7 possible trouble
groups, AC is present
1-7 possible trouble
groups, AC is not present
Viewing System Trouble(s)
Press the R4 key on the keypad.
To determine the System Trouble Group
Number, count the number of times the
HSYSTEM TROUBLE LED blinks. The keypad
sounder will beep at the same rate that the
HSYSTEM TROUBLE LED blinks.
To determine the System Trouble, note the
zone LED that is ON. Look up the specific
system trouble on the chart on the following
page.
The HSYSTEM TROUBLE LED and keypad
sounder will continue to flash and beep. To view
the next System Trouble, if any, press P.
Continue pressing P, if there are no more
system troubles to view, the system will return to
normal operation.
26
ED
ARM
T
ST A
2
US
Flashing
(System Trouble
Group Number)
Beeping
(System Trouble
Group Number)
Zone LED(s) is ON
indicates
(Specific Trouble)
Audible System Trouble Indication - For all
system troubles, except when the only system
trouble is the loss of AC, the keypad will beep
once every 10 seconds.
The keypad will
continue to beep until the reset button is pressed
or the trouble has been acknowledged by
pressing the C key.
System Trouble Reporting
System Trouble
Group #
Keypad SYSTEM Trouble
LED is flashing 1 time
indicating System Trouble
Group 1.
Keypad Sounder beeps 1
time indicating System
Specific Trouble
Zone 2 LED is ON indicating
Low Battery. (1 Beep, LED 2)
The following system troubles, when enabled to
report to Telco 1 [37-3] or Telco 3 [57-3], will
send the report code programmed in Trouble
Report [63] if reporting using a pulse format:
System Trouble
Bell Cut
2-Wire Fire Trouble
Rcvr Fail-to-Respond
Receiver Tamper
Receiver JAM
Tx Low Battery
Tx Supervisory Failure
Smoke Low Battery
Smoke Sup. Failure
If reporting using Point ID, a unique code will be
sent for each of the following System Troubles.
System Trouble
FIGURE 9 SYSTEM TROUBLE EXAMPLE
Note: System Troubles Groups 3 through 7 System Trouble Groups that have a zone or
smoke detector associated with the trouble,
such as RF low battery. The zone(s) of the
device with a low battery will be displayed by the
ZONE LED. For example, a wireless low battery
on zone 2 would beep the keypad sounder 3
times and turn on zone 2 LED.
Pulse Report Code
F1
F1
F1
F1
F1
F1
F1
F1
F1
Bell Cut
2-Wire Fire Trouble
Rcvr Fail-to-Respond
Receiver Tamper
Receiver JAM
Tx Low Battery
Tx Supervisory Failure
Point ID Report Codes
CODE 1 321 G00 ZN000-BELL 1 TROUBLE
CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
CODE 1 382 G00 ZN000-SENSOR TROUBLE
CODE 1 145 G00 ZN000-EXP. MODL. TAMPER
CODE 1 333 G00 ZN000-FIRE LOOP TRBLE
CODE 1 384 G00 ZN00n-RF TRAN LOW BATT
CODE 1 381 G00 ZN00n-SUPERVSN LOSS RF
A 300 (SYSTEM TROUBLE RST) code is sent if a restore is
reported after multiple troubles.
System Troubles
Keypad Beeps or
SYSTEM Flashes
Zone LED
ON
1 Beep
1
AC Power Failure
This trouble will occur if AC power is not present. Ensure that the transformer is connected to an unswitched power source.
2
Low Battery
If there has been a recent power failure, the battery may be partially depleted and must be recharged by the control panel. If the
trouble does not go away in 24 hours, replace the battery.
3
Communication Failure /
PCPreset Fail / Line Fail
The system was not able to report to central station. Check panel programming and telephone line wiring. The trouble will clear after it
has been acknowledged by viewing the system trouble as long as the telephone line has passed a line cut test (tested automatically by
the panel). The Panel did not successfully connect and download/upload with the computer running PCPreset - check Auto Download
ID number, Callback Number or PCPreset Setup.
4
Telephone Line Cut
The telephone line has failed. If telephone service has been temporarily interrupted, the trouble will clear when restored and
acknowledged by viewing the system trouble.
1
Bell/Siren line Cut
There is a problem with the Bell or Siren wiring. EOL2.2K resistor must be installed.
2
2-wire Fire Trouble
There is a problem with the wiring of the Fire Zone.
3
Rcvr Fail-to-Respond/Rcvr
Tamper
The receiver is not responding to the panel. The red LED on the receiver should be flashing, refer to WI850. The cover is off the
receiver causing a tamper signal to be transmitted.
4
Receiver Jam
A signal is blocking the normal reception of transmissions from the wireless devices. Ensure that the green LED on the receiver is not
on continuously, refer to receiver manual WI850.
2 Beeps
System Trouble
Condition
Cause/Action
3 Beeps
1-6
Wireless
Transmitter Low Battery
The battery in the wireless transmitter is low and should be replaced. This transmitter is on the zone corresponding to the number of
the zone light flashing. The replacement battery for the GEM-TRANS2 door/window transmitter and the GEM PIR wireless motion
detector is the Duracell DL123A. (2 required for the GEM-PIR) WARNING: Replace batteries only with the same type as specified
above. Use of another battery may present a risk of fire or explosion. Do not recharge or disassemble battery or dispose of in fire.
4 Beeps
1-6
The panel has not received a supervisory signal from the transmitter within the time programmed. Check Wireless Supervisory Timer
[16] Programming. Check the placement of the transmitter and receiver, refer to WI850.
5 Beeps
1-4
Wireless
Transmitter
Supervisory Failure
Wireless Smoke Detector
Low Battery
6 Beeps
1-4
Wireless Smoke Detector
Supervisory
The panel has not received a supervisory signal from the wireless smoke detector within the programmed time. Check Wireless
Smoke Supervisory Timer [17] Programming. Check the placement of the wireless smoke detector and receiver, refer to WI850.
7 Beeps
1-6
Zone Trouble
The panel has one or more of the following 2 possible troubles: Transmitter Tamper, Dual Tech Self Test Fail, or 24 hr Zone Type.
The battery in the wireless smoke detector is low and should be replaced. This wireless smoke detector should be marked with a
number corresponding to the number of the zone light flashing. The replacement batteries required are *Duracell 9 Volt Alkaline (2).
27
WI1089A GEM-P801 Installation Instructions
Troubleshooting
1. The bell output drops to about 3 volts
in alarm.
The battery/bell circuit is protected by a
PC board trace which may have burned
open by reversal of the battery leads. It is
on the back of the PC board just adjacent
to the red & black battery leads. Send in
for service if this occurs.
2. How do I remove the Keypad Sounder
on Alarm?
The keypad sounder follows the Burg
Output. If you need to remove the Keypad
Sounder, then you must remove the Burg
Output from that zone.
3. How do I activate Chime by Zone?
The Chime feature will automatically be
assigned to all zones, except for the
following:
3. Zones programmed as Home/Away
28
with Delay Zones programmed as
Exit/Entry Followers
4. Zones programmed for 24 Hour
Protection. To Activate/Deactivate the
chime mode, Press R5.
4. When using a piezo on the Bell Output,
it constantly buzzes.
This is due to the fact that there is a
constant loop current flowing through the
Bell circuit for supervision. To eliminate
this, cut resistor R26 which is located
directly above Terminal 9 just below the
heat sink.
5. Where are the fuses?
The control panel incorporates advanced
circuitry which automatically limits the
current when an over current condition
exists without the use of traditional fuses.
The circuit will restore automatically when
the over current condition is corrected.
6. The PGM Output Pulses in Alarm.
When the PGM lug of the control panel is
programmed for an Armed indication it
also incorporates an Alarm Memory
function which will indicate that the
system is in an Alarm condition.
7. I short out the bell and the system
does not indicate Bell Trouble.
The Bell Supervision circuit is only
designed to detect a "Bell Cut", it does
not supervise for a short on the Bell.
8.
9.
How do I remove Keypad Sounder on
Alarm?
wired to point 1, and point 2 is jumped
out.
The keypad sounder follows the Burg
Output. If you need to remove the
Keypad Sounder, then you must remove
the Burg Output from that zone.
If using internal reed, make sure J1 is
cut and both Point 1 and Point 2
terminals are jumped out.
Transmitters not responding?
Open Transmitter case - Keypad should
go into X-Mitter Tamper Trouble. If not:
Check Receiver Red LED should be
flashing once approx. once a second.
Check Receiver wiring.
Check Programming of Transmitter ID.
10. Keypad LEDs Flicker.
The Keypad is not receiving a POLL
from the Panel.
Check Keypad wiring.
R9
to turn keypad sounds back
on.
12. No Keypad Chime?
The keypad sounder is turned off with
the R9 command. This command
will silence all Keypad sounds except
keypad sounder on alarm. Enter
R9 to turn keypad sounds back
on.
1. The Panel is in the process of being
Uploaded/Downloaded.
2. The panel is powering up. LED’s will
flicker until panel has reset and is
polling the keypad.
3. The connection from the control
panel to the keypad is open.
If Keypad does go into X-Mitter Tamper
Trouble, check:
Transmitter
correctly.
point
is
programmed
Transmitter is wired correctly:
If using external switch, make sure it is
11. No Keypad Entry Sounder during
Entry Time?
The keypad sounder is turned off with
the R9 command. This command
will silence all Keypad sounds except
keypad sounder on alarm. Enter
29
WI1089A GEM-P801 Installation Instructions
GEM-K800
30
NOTES
31
NAPCO LIMITED WARRANTY
any other warranty or liability concerning its products. In no event shall NAPCO be liable
for an amount in excess of NAPCO's original selling price of the product, for any loss or
damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any
failure of the product. Seller's warranty, as hereinabove set forth, shall not be enlarged,
This warranty shall not apply to any equipment, or any part thereof, which has been diminished or affected by and no obligation or liability shall arise or grow out of Seller's
repaired by others, improperly installed, improperly used, abused, altered, damaged, rendering of technical advice or service in connection with Buyer's order of the goods
subjected to acts of God, or on which any serial numbers have been altered, defaced or furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED
removed. Seller will not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND WEEKLY.
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from
manufacturing defects in materials and workmanship for thirty-six months following the
date of manufacture. NAPCO will, within said period, at its option, repair or replace any
product failing to operate correctly without charge to the original purchaser or user.
THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED Warning: Despite frequent testing, and due to, but not limited to, any or all of the following;
WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A criminal tampering, electrical or communications disruption, it is possible for the system to
PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL fail to perform as expected. NAPCO does not represent that the product/system may not
be compromised or circumvented; or that the product or system will prevent any personal
OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of injury or property loss by burglary, robbery, fire or otherwise; nor that the product or
merchantability, must be brought within the six months following the end of the warranty system will in all cases provide adequate warning or protection. A properly installed and
period. IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it is not
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER
OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR
OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING.
CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
Therefore, the installer should in turn advise the consumer to take any and all precautions
In case of defect, contact the security professional who installed and maintains your for his or her safety including, but not limited to, fleeing the premises and calling police or
security system. In order to exercise the warranty, the product must be returned by the fire department, in order to mitigate the possibilities of harm and/or damage. NAPCO is
security professional, shipping costs prepaid and insured to NAPCO. After repair or not an insurer of either the property or safety of the user's family or employees, and limits
replacement, NAPCO assumes the cost of returning products under warranty. NAPCO its liability for any loss or damage including incidental or consequential damages to
shall have no obligation under this warranty, or otherwise, if the product has been repaired NAPCO's original selling price of the product regardless of the cause of such loss or
by others, improperly installed, improperly used, abused, altered, damaged, subjected to damage.
accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been
altered, defaced or removed. NAPCO will not be responsible for any dismantling, Some states do not allow limitations on how long an implied warranty lasts or do not allow
reassembly or reinstallation charges. This warranty contains the entire warranty. It is the the exclusion or limitation of incidental or consequential damages, or differentiate in their
sole warranty and any prior agreements or representations, whether oral or written, are treatment of limitations of liability for ordinary or gross negligence, so the above limitations
either merged herein or are expressly canceled. NAPCO neither assumes, nor authorizes or exclusions may not apply to you. This Warranty gives you specific legal rights and you
any other person purporting to act on its behalf to modify, to change, or to assume for it, may also have other rights which vary from state to state.
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.
This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause
interference to radio and television reception. It has been type tested and found to comply with the limits for a Class-B computing device in accordance with the specifications in
Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient the receiving antenna;
relocate the computer with respect to the receiver; move the computer away from the receiver; plug the computer into a different outlet so that computer and receiver are on different
branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet
prepared by the Federal Communications Commission helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government
Printing Office, Washington, DC 20402; Stock No. 004-000-00345-4.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement