11 KB

11 KB
MP-2 Instruction Manual
VHF Wattmeter
MP-2
VHF WATTMETER
The MIRAGE MP-2 is designed to provide the VHF amateur with a versatile wattmeter
without having to use cumbersome add-ons or plug-ins.
The MP-2 will measure forward or reverse power in three power ranges - 50, 500, and
1,500 Watts. It will display either average or peak power. This allows for the best
display of power output, whether on FM, CW, or SSB.
When checking antennas, the MP-2 will display SWR directly, without using extra charts
or graphs. Optimum tuning and adjustment of the antenna is possible, even with as little
as 2 Watts from the transmitter.
The coupling unit may be mounted up to four feet from the meter, providing neater
installations.
SPECIFICATIONS
Frequency Range........ 50 - 200 MHz
(calibrated at 145 MHz)
Line Impedance........... .......................................................... 50 Ohms resistive
Functions.................... Power - Forward / Reverse
Power Range.............. 50, 500, and 1,500 Watts
(±5% RF Calibration, ±1%
meter)
Power Capability......... .......................................................... 1,000 Watts continuous
1,500 Watts intermittent
SWR Sensitivity.......... .......................................................... 1 to 2 Watts
DC Power Requirement ........................................................ 9 VDC internal battery or
optional AC adapter
Size.....5.75" H x 4.5" W x 5.75" D
INSTALLATION
The MP-2 coupler has two S0239 connectors marked INPUT and OUTPUT. The radio
is connected to the INPUT connector and the load, or antenna, is connected to the
OUTPUT connector.
The coupler may be remotely mounted by removing the two screws that secure it to the
meter case. Replace the two screws back into the coupling unit.
CONTROL
Range Switch - This switch selects the full scale power that is to be read. It also turns
the unit ON and OFF.
1
MP-2 Instruction Manual
VHF Wattmeter
PEAK / AVG Switch - This switch selects the desired display of power. AVG for CW,
FM, AM, or averaging of SSB. This shows the true peak power output.
FWD / REV - "FWD" shows the power that is being transmitted, while "REV" shows the
returned or reflected power.
SWR CAL / PWR CAL - When reading power, this control is set at full counterclockwise, in the PWR CAL position. For SWR this control is turned clockwise, to
adjust the meter to read full scale.
LOW BAT - When the internal 9-Volt battery drops to approximately 6.75 Volts, the
LED will start to flash, indicating that it is time to change the battery.
OPERATION
Power - To measure power, connect the MP-2 between the transmitter and the load.
Select the desired power range, set the "SWR CAL / PWR CAL" switch to "PWR
CAL." To display the forward power, set the "FWD / REV" switch to "FWD." For
reverse or reflected power, switch to "REV." The actual power being transmitted is the
difference between the forward and reverse power reading.
Peak or Average Power - For FM, AM, Slow Speed CW, or to measure your average
power on SSB, put the switch on "AVG." With the switch on "PEAK," the actual peak
power will be displayed. This can be used on AM, Fast CW, and SSB.
SWR - Connect the MP-2 between the transmitter and the load to be measured. Set the
range switch to the proper power range and the "FWD / REV" switch to FWD. Key the
transmitter and adjust the SWR CAL to give a full-scale reading. Switch to REV and
read SWR on the SWR scale of the meter. SWR may be measured with input powers
between 1 and 2 Watts to over 800 Watts. The best accuracy is obtained with 10 to 15
Watts, which is the recommended power range, for SWR measurements.
AC Adapter - Any 9 to 15 Volt DC output adapter that uses a 0.1 inch center pin may be
used to power the MP-2 and to extend the battery life. When the adapter is plugged in,
the battery is disconnected.
Maintenance - The MP-2 is designed to give years of trouble-free performance. It is
recommended that the MP-2 be returned to the factory for any required service or
calibration.
Battery Change - The battery is located inside the back cover. When the "LOW BAT
LED" flashes, replace the battery with a fresh 9-Volt battery (Eveready 216 or
equivalent).
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement