VIA Technologies EPIA-NX User`s manual

VIA Technologies EPIA-NX User`s manual
User’s Manual
EPIA-NR
Version 1.0
June 15, 2007
Copyright
Copyright © 2005-2007 VIA Technologies Incorporated. All rights reserved.
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise without the prior written permission of VIA
Technologies, Incorporated.
Trademarks
All trademarks are the property of their respective holders. PS/2 is a registered trademark of
IBM Corporation. Award BIOS is a registered trademark of Phoenix Technologies Ltd.
Macrovision
Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,819,098; 4,907,093; 5,315,448; 6,516,132
licensed for limited viewing uses only.
This product incorporates copyright protection
technology that is protected by certain U.S. patents and other intellectual property rights owned
by Macrovision and other rights owners. Use of this copyright protection technology must be
authorized by Macrovision, and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
Disclaimer
No license is granted, implied or otherwise, under any patent or patent rights of VIA
Technologies. VIA Technologies makes no warranties, implied or otherwise, in regard to this
document and to the products described in this document. The information provided in this
document is believed to be accurate and reliable as of the publication date of this document.
However, VIA Technologies assumes no responsibility for the use or misuse of the information
in this document and for any patent infringements that may arise from the use of this
document. The information and product specifications within this document are subject to
change at any time, without notice and without obligation to notify any person of such change.
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at his
personal expense.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with
the emission limits.
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Safety Instructions
1.
Always read the safety instructions carefully.
2.
Keep this User's Manual for future reference.
3.
Keep this equipment away from humidity.
4.
Lay this equipment on a reliable flat surface before setting it up.
5.
The openings on the enclosure are for air convection hence protects the equipment from
6.
Make sure the voltage of the power source and adjust properly 110/220V before
overheating. DO NOT COVER THE OPENINGS.
connecting the equipment to the power inlet.
7.
Place the power cord in such a way that people cannot step on it. Do not place anything
8.
Always unplug the power cord before inserting any add-on card or module.
9.
All cautions and warnings on the equipment should be noted.
over the power cord.
10. Never pour any liquid into the opening. Liquid can cause damage or electrical shock.
11. If any of the following situations arises, get the equipment checked by a service personnel:
•
The power cord or plug is damaged
•
Liquid has penetrated into the equipment
•
The equipment has been exposed to moisture
•
The equipment has not work well or you cannot get it work according to User's
Manual.
•
The equipment has dropped and damaged
•
If the equipment has obvious sign of breakage
12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED,
OR IN A STORAGE TEMPERATURE ABOVE 60oC (140oF). THE EQUIPMENT
MAY BE DAMAGED.
CAUTION: Explosion or serious damage may occur if the battery is
incorrectly replaced.
Replace only with the same or equivalent
battery type recommended by the manufacturer.
BOX CONTENTS
One VIA Nano-ITX Mainboard
One VGA Ribbon Cable
One ATA-133/100 IDE Ribbon Cable
One Driver and Utilities CD
One IO Bracket
Two Screws for VGA Connector
Chapter 3
TABLE OF CONTENTS
Box Contents.................................................................................. 5
Table of Contents ........................................................................... 6
Chapter 1 ...................................................................................... 8
Specifications .............................................................................. 8
Mainboard Specifications .............................................................. 9
Mainboard Layout ...................................................................... 11
Back Panel Layout ..................................................................... 12
Chapter 2 .................................................................................... 13
Installation ............................................................................... 13
CPU.......................................................................................... 14
Memory Module Installation ........................................................ 16
Connecting the Power Supply...................................................... 17
Back Panel Ports........................................................................ 18
Connectors ............................................................................... 19
Jumpers ................................................................................... 25
Slots ........................................................................................ 27
Chapter 3 .................................................................................... 28
BIOS Setup ............................................................................... 28
Entering Setup .......................................................................... 29
Control Keys ............................................................................. 30
Navigating the BIOS Menus ........................................................ 31
Getting Help.............................................................................. 32
Main Menu ................................................................................ 33
Standard CMOS Features ............................................................ 35
IDE Drives ................................................................................ 36
Advanced BIOS Features ............................................................ 37
CPU Feature.............................................................................. 41
Hard Disk Boot Priority ............................................................... 43
Advanced Chipset Features ......................................................... 44
AGP & P2P Bridge Control........................................................... 46
CPU & PCI Bus Control ............................................................... 48
Integrated Peripherals................................................................ 49
VIA OnChip PCI Device............................................................... 50
USB Device Setting .................................................................... 51
BIOS Setup
Power Management Setup .......................................................... 53
Wakeup Event Detect................................................................. 55
PNP/PCI Configurations .............................................................. 57
PC Health Status........................................................................ 59
Frequency / Voltage Control ....................................................... 60
DRAM Clock/Drive Control .......................................................... 61
Load Fail-Safe Defaults............................................................... 63
Load Optimized Defaults............................................................. 64
Set Supervisor / User Password................................................... 65
Save & Exit Setup ...................................................................... 67
Exit Without Saving ................................................................... 68
Chapter 4 .................................................................................... 69
Driver Installation ...................................................................... 69
Driver Utilities ........................................................................... 70
CD Content ............................................................................... 72
CHAPTER 1
Specifications
The ultra-compact and highly integrated VIA EPIA-NR uses the NanoITX mainboard form-factor developed by VIA Technologies, Inc. as
part of the company’s open industry-wide total connectivity initiative.
The mainboard enables the creation of an exciting new generation of
small, ergonomic, innovative and affordable embedded systems.
Through a high level of integration, the Nano-ITX occupies only 50%
of the size of Mini-ATX mainboard form factor. The mainboard comes
with an embedded VIA Processor, boasting of ultra-low power
consumption, cool and quiet operation.
BIOS Setup
MAINBOARD SPECIFICATIONS
CPU
•
VIA C7® 1.0GHz NanoBGA2 processor
Chipset
•
VIA CX700 Advanced All-in-One chipset
Graphics
•
Integrated UniChrome™ Pro II 3D/2D AGP graphics with MPEG-2
video decoding acceleration
Audio
•
VIA VT1708A High Definition Audio Codec
Memory
•
1 x DDR2 533 SODIMM slot (up to 1 GB)
Expansion Slot
•
1 x Mini-PCI slot
•
1 x UltraDMA 133/100 connector (2.54mm, 40-pin)
IDE
Serial ATA
•
2 x SATA connectors
LAN
•
VIA VT6107 10/100 Mbps Fast Ethernet Controller or VIA VT6122
Gigabit Ethernet Controller (Optional)
Chapter 3
Back Panel I/O Ports
•
1 x RJ45 LAN port
•
1 x VGA port
Onboard I/O Connectors
•
1 x USB pin connector for 6 additional USB 2.0 ports
•
1 x LPC pin connector
•
1 x SMBus pin connector
•
2 x Serial port pin connectors (COM 1 5V/12V selectable)
•
2 x LVDS Power pin connectors
•
1 x LVDS Panel pin connector to support 2 single-channel LVDS
panels or 1 dual-channel panel (optional)
•
1 x CF (Compact Flash) Type I connector (shared with IDE, master /
slave select by jumpers)
•
1 x PS2 Mouse/Keyboard pin connector
•
1 x Audio pin connector for Line-out, Line-in, MIC-in, and S/PDIF out
•
1 x Front Panel pin connector
•
2 x Fan connectors for CPU and system fans
•
1 x Nano-ITX power connector
BIOS
•
Award BIOS with LPC 4/8Mbit flash memory capacity
Form Factor
•
Nano-ITX (8-layer)
•
12cm X 12cm
BIOS Setup
MAINBOARD LAYOUT
Chapter 3
BACK PANEL LAYOUT
CHAPTER 2
Installation
This chapter provides you with information about hardware
installation procedures. It is recommended to use a grounded wrist
strap before handling computer components. Electrostatic discharge
(ESD) can damage some components.
Chapter 3
CPU
The VIA EPIA-NR Nano-ITX mainboard includes an embedded VIA C7 V4 Bus
Processor. The VIA C7 V4 Bus Processor requires only a heatsink to provide
sufficient cooling.
CX700
VIA
C7
CPU
BIOS Setup
CPU Fan and System Fan: CPUFAN and SYSFAN
The CPUFAN (CPU fan) and SYSFAN (system fan) run on +12V and maintain
system cooling. When connecting the wire to the connectors, always be
aware that the red wire is the Positive and should be connected to the +12V.
The black wire is Ground and should always be connected to GND.
CPUFAN
Pin
Signal
1
2
3
NC
+12V
GND
SYSFAN
Pin
Signal
1
2
3
NC
+12V
GND
CPUFAN
1
SYSFAN
1
Chapter 3
MEMORY MODULE INSTALLATION
Memory Slot: DDR2_SODIMM
The VIA EPIA-NX Nano-ITX mainboard provides one SODIMM slot for DDR2
533 SDRAM memory modules and supports memory sizes up to 1GB.
Insert the SODIMM module at a 45 degree angle.
Push the SODIMM module back towards the board until the clips lock the
module in place.
Available DDR2 SDRAM Configurations
Refer to the table below for available DDR2 SDRAM configurations on the
mainboard.
Slot
Module Size
SODIMM
64MB, 128MB, 256MB, 512MB, 1GB
Maximum supported system memory
Total
64MB-1GB
64MB-1GB
BIOS Setup
CONNECTING THE POWER SUPPLY
The VIA EPIA-NX Nano-ITX mainboard supports a Nano-ITX power supply for
the power system.
Before inserting the power supply connector, always
make sure that all components are installed correctly to ensure that no
damage will be caused.
Nano-ITX 12-Pin Power Connector
To connect the power supply, make sure the power plug is inserted in the
proper orientation and the pins are aligned. Then push down the plug firmly
into the connector.
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
+3.3V
+3.3V
+3.3V
+5VSUS
GND
+12V
-PSON
+5V
GND
+5V
GND
PWRGD
1
2
3
4
5
6
7
8
9
10
11
12
Chapter 3
BACK PANEL PORTS
The back panel has the following ports:
VGA Port
The 15-pin female VGA connector can be used to connect to any analog VGA
monitor.
RJ45 LAN Port
The mainboard provides a standard RJ45 port for enabling connections to
networks.
BIOS Setup
CONNECTORS
IDE Connector: IDE
The mainboard has an Ultra DMA 133/100 controller. You can connect up to
two IDE devices in any combination.
1
If two drives are connected to a single cable, the jumper on the second drive
must be set to slave mode. Refer to the drive documentation supplied by the
vendor for the jumper settings.
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
#IDE_RST
PD_7
PD_6
PD_5
PD_4
PD_3
PD_2
PD_1
PD_0
GND
#PD_REQ
#PD_IOW
#PD_IOR
#PD_RDY
#PD_ACK
PD_IRQ15
PD_A1
PD_A0
#PD_CS1
#HD_LED1
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
GND
PD_8
PD_9
PD_10
PD_11
PD_12
PD_13
PD_14
PD_15
NC
GND
GND
GND
PRIMARY
GND
NC
IDE_DMADET
PD_A2
#PD_CS3
GND
Chapter 3
Serial ATA Connectors: SATA1 and SATA2
These next generation connectors support the right angle Serial
ATA cables for primary internal storage devices. The current
Serial ATA interface allows up to 150MB/s data transfer rate,
faster than the standard parallel ATA with 133 MB/s (Ultra DMA).
USB Pin Connector: USB
The mainboard provides 1 USB pin connector that allows up to 6 USB 2.0
ports to be added.
This port can be used to connect high-speed USB
interface peripherals such as USB HDD, digital cameras, MP3 players, printers,
modem and the like.
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
VUSB0
USBD_T0+
USBD_T0GND
USBD_T1USBD_T1+
GND
VUSB4
USBD_T4USBD_T4+
GND
KEY
2
4
6
8
10
12
14
16
18
20
22
24
VUSB2
USBD_T2+
USBD_T2GND
USBD_T3USBD_T3+
KEY
VUSB4
USBD_T5USBD_T5+
GND
GND
1
24
BIOS Setup
Case Connector: FPNL
The FPNL pin header allows you to connect the power switch, reset switch,
power LED, HDD LED and the case speaker.
Pin
Signal
Pin
Signal
1
3
5
7
9
11
+PWR_LED
+PWR_LED
-PWR_LED
SPEAK+
KEY
SPEAK-
2
4
6
8
10
12
+HD_LED
-HD_LED
PW_BN
GND
RST_SW
GND
1
Power Switch (PW_BN)
Connect to a 2-pin power button switch. Pressing this button will turn the
system power on or off.
Reset Switch (RST_SW)
The reset switch is used to reboot the system rather than turning the power
ON/OFF. Avoid rebooting the system, if the HDD is still working. Connect
the reset switch from the system case to this pin.
Power LED (PWR_LED)
The LED will light when the system is on. If the system is in S1 (POS - Power
On Suspend) or S3 (STR - Suspend To RAM) state, the LED will blink.
HDD LED (HD_LED)
HDD LED shows the activity of a hard disk drive. Avoid turning the power off
when the HDD LED still has a lit. Connect the HDD LED from the system case
to this pin.
Speaker (SPEAK)
The speaker from the system case is connected to this pin.
Chapter 3
Audio Connector: AUDIO
This is an interface for connections to external audio devices.
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
SPDIF_OUT
GND
LINEOUT_R
LINEIN_R
MICIN1_R
KEY
AGND
2
4
6
8
10
12
14
+5V
KEY
LINEOUT_L
LINEIN_L
MICIN1_L
NC
AGND
1
KBMS Connector: KB/MS
The mainboard provides a PS2 pin header to attach a PS2 keyboard and
mouse.
Pin
Signal
Pin
Signal
1
3
5
7
9
VCCE
NC
GND
KB_DT
KB_CK
2
4
6
8
10
VCCE
KEY
GND
MS_DT
MS_CK
1
Serial Port Connectors: COM1 / COM2
COM1/2 pin headers can be used to attach additional ports for serial mouse
or other serial devices.
Pin
Signal
Pin
Signal
1
3
5
7
9
DCD
TXD
GND
RTS
RI
2
4
6
8
10
RXD
DTR
DSR
CTS
Key
1
BIOS Setup
LVDS Panel Connector: PANEL
The LVDS Panel connector allow you to connect the panel’s LVDS cable
directly to support 2 single-channel LVDS panels or 1 dual-channel LVDS
panel (optional) without any need of a daughter card.
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
PVDD2
PVDD2
PVDD2
GND
-LD2C4
+LD2C4
GND
-LD2C5
+LD2C5
GND
-LD2C6
+LD2C6
GND
-LCLK2
+LCLK2
GND
-LD2C7
+LD2C7
SPCLK1
SPD1
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
PVDD1
PVDD1
PVDD1
GND
-LD1C0
+LD1C0
GND
-LD1C1
+LD1C1
GND
-LD1C2
+LD1C2
GND
-LCLK1
+LCLK1
GND
-LD1C3
+LD1C3
GPIOA_CLK
GPIOB_DATA
2
1
40
39
Inverter Connectors: INVERTER1 / INVERTER2
The mainboard provides 2 inverters for supplying power to the backlight of
the LCD panel.
Pin
Signal
1
2
3
4
5
6
7
8
IVDD
IVDD
BLON
NC
BLON
BR_CNTR
GND
GND
1
Chapter 3
LPC Connector: LPC
This pin connector is for LPC devices as well as panel power
1
select jumper.
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
PVDD1_PWR
PVDD1_PWR
PVDD2_PWR
PVDD2_PWR
LPC_AD1
-PCI_RST1
LPC_AD0
LPC_AD2
SERIRQ
-LPC_DRQ0
+5V
+5V
GND
GND
2
4
6
8
10
12
14
16
18
20
22
24
26
28
+3.3V
+5V
+3.3V
+5V
SIO_33_CLK
GND
SIO_48_CLK
-LPC_FRAME
LPC_AD3
-EXTSMI
+3.3V
+3.3V
GND
Key
System Management Bus Connector: SMBus
This pin header allows you to connect SMBus (System Management Bus)
devices. Devices communicate with an SMBus host and/or other SMBus
devices using the SMBus interface.
Pin
Signal
1
2
3
SMBCK
SMBDT
GND
1
BIOS Setup
JUMPERS
The mainboard provides jumpers for setting some mainboard functions. This
section will explain how to change the settings of the mainboard functions
using the jumpers.
Clear CMOS: CLEAR_CMOS
The onboard CMOS RAM stores system configuration data and has an
onboard battery power supply. To reset the CMOS settings, set the jumper
on pins 2 and 3 while the system is off. Return the jumper to pins 1 and 2
afterwards. Setting the jumper while the system is on will damage the
mainboard.
Setting
1
2
3
Normal Operation
Clear CMOS setting
ON
OFF
ON
ON
OFF
ON
Normal:
1 2 3
Clear:
1 2 3
WARNING: Except when clearing the RTC RAM, never remove the
cap on CLEAR_CMOS1 jumper default position.
will cause system boot failure.
Removing the cap
Avoid clearing the CMOS while the
system is on; it will damage the mainboard.
CF Mode Selector: J1
J1 is the working mode selector for CF Type I connector.
Short = Master; Open = Slave
1
Chapter 3
Inverter Selector: IVDD_SEL
IVDD is the VCC selector jumper to determine the input voltage of the panel
inverter for panel’s back-light.
1 3 5
+5V:
Setting
1
2
3
4
5
6
+5V
+12V
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
1 3 5
+12V:
Panel Power Selector: LPC
The LPC connector contains the VCC selector jumper to determine the panel’s
signal voltage.
2 4 6 8
Setting
1
2
3
4
5
6
7
8
+3.3V
+5V
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
OFF
ON
OFF
OFF
ON
OFF
ON
+3.3V:
2 4 6 8
+5V:
COM1 Power Selector: J2
J2 is a VCC selector jumper to determine the input voltage for COM1
connector.
Setting
1
2
3
+5V
+12V
ON
OFF
ON
ON
OFF
ON
+5V:
1 2 3
+12V:
1 2 3
BIOS Setup
SLOTS
Mini Peripheral Component Interconnect: MINIPCI
The miniPCI slot allows you to insert a miniPCI expansion card. First unplug
the power supply before adding or removing expansion cards.
Read the
documentation for the expansion card to see if any changes to the system are
necessary.
PCI Interrupt Request Routing
The IRQ (interrupt request line) are hardware lines over which devices can
send interrupt signals to the microprocessor. The “PCI & LAN” IRQ pins are
typically connected to the PCI bus INT A# ~ INT D# pins as follows:
miniPCI Slot
Order 1
Order 2
Order 3
Order 4
INT B#
INT C#
INT D#
INT A#
Compact Flash Type I Connector: CF1
This CF1 connector allows you to connect to a passive 50-pin Type I adapter.
CHAPTER 3
BIOS Setup
This chapter gives a detailed explanation of the BIOS setup functions.
BIOS Setup
ENTERING SETUP
Power on the computer and press <Delete> during the beginning of the boot
sequence to enter the BIOS setup menu. If you missed the BIOS setup entry
point, you may restart the system and try again.
Chapter 3
CONTROL KEYS
Keys
Description
Up Arrow
Down Arrow
Left Arrow
Right Arrow
Enter
Escape
Move to the previous item
Move to the next item
Move to the item in the left side
Move to the item in the right side
Select the item
Jumps to the Exit menu or returns to the main menu from a
submenu
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Restore the previous CMOS value from CMOS, only for
Option Page Setup Menu
Load the default CMOS value from Fail-Safe default table,
only for Option Page Setup Menu
Load Optimized defaults
Jumps to the Main Menu
Save all the CMOS changes and exit
Page Up / +
Page Down / F1
F5
F6
F7
F9
F10
BIOS Setup
NAVIGATING THE BIOS MENUS
The main menu displays all the BIOS setup categories. Use the Up/Down/
Left/Right arrow keys to select any item or sub-menu.
Description of the
selected/highlighted category is displayed at the bottom of the screen.
An arrow symbol next to a field indicates that a sub-menu is available (see
figure below).
Press <Enter> to display the sub-menu.
menu, press <Esc>.
To exit the sub-
Chapter 3
GETTING HELP
The BIOS setup program provides a “General Help” screen. You can display
this screen from any menu/sub-menu by pressing <F1>.
The help screen
displays the keys for using and navigating the BIOS setup. Press <Esc> to
exit the help screen.
BIOS Setup
MAIN MENU
Phoenix - AwardBIOS CMOS Setup Utility
Frequency / Voltage Control
Standard CMOS Features
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP / PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Esc : Quit
F9 : Menu in BIOS
: Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type...
Standard CMOS Features
Use this menu to set basic system configurations.
Advanced BIOS Features
Use this menu to set the advanced features available on your system.
Advanced Chipset Features
Use this menu to set chipset specific features and optimize system
performance.
Integrated Peripherals
Use this menu to set onboard peripherals features.
Power Management Setup
Use this menu to set onboard power management functions.
PnP/PCI Configurations
Use this menu to set the PnP and PCI configurations.
PC Health Status
This menu shows the PC health status.
Chapter 3
Frequency/Voltage Control
Use this menu to set the system frequency and voltage control.
Load Fail-Safe Defaults
Use this menu option to load the BIOS default settings for minimal and stable
system operations.
Load Optimized Defaults
Use this menu option to load BIOS default settings for optimal and high
performance system operations.
Set Supervisor Password
Use this menu option to set the BIOS supervisor password.
Set User Password
Use this menu option to set the BIOS user password.
Save & Exit Setup
Save BIOS setting changes and exit setup.
Exit Without Saving
Discard all BIOS setting changes and exit setup.
BIOS Setup
STANDARD CMOS FEATURES
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Tue, Jul 13 1999
11 : 20 : 55
Item Help
Menu Level
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
Change the day, month, year
and century
[EGA/VGA]
[All , But Keyboard]
Video
Halt On
Base Memory
Extended Memory
Total Memory
640K
15360K
16384K
: Move
Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
Date
The date format is [Day, Month Date Year]
Time
The time format is [Hour : Minute : Second]
Video
Settings:[EGA/VGA, CGA 40, CGA 80, MONO]
Halt On
Sets the system’s response to specific boot errors.
Below is a table that
details the possible settings.
Setting
Description
All Errors
No Errors
All, But Keyboard
System halts when any error is detected
System does not halt for any error
System halts for all non-key errors
Chapter 3
IDE DRIVES
Phoenix - AwardBIOS CMOS Setup Utility
IDE Channel 0 Master
IDE HDD Auto-Detection
[Press Enter]
IDE Channel 0 Master
Access Mode
[Auto]
[Auto]
Capacity
0 MB
Cylinder
Head
Precomp
Landing Zone
Sector
0
0
0
0
0
: Move
Enter: Select
F5: Previous Values
Item Help
Menu Level
To auto-detect the HDD's size,
head... on this channel
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
The specifications of your drive must match with the drive table. The hard
disk will not work properly if you enter incorrect information in this category.
Select “Auto” whenever possible.
If you select “Manual”, make sure the
information is from your hard disk vendor or system manufacturer. Below is
a table that details required hard drive information when using the “Manual”
mode.
Setting
Description
IDE Channel
The name of this match the name of the menu. Settings:
[None, Auto, Manual]
Settings: [CHS, LBA, Large, Auto]
Formatted size of the storage device
Number of cylinders
Number of heads
Write precompensation
Cylinder location of the landing zone
Number of sectors
Access Mode
Capacity
Cylinder
Head
Precomp
Landing Zone
Sector
BIOS Setup
ADVANCED BIOS FEATURES
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU Feature
Hard Disk Boot Priority
Virus Warning
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Boot Up NumLock Status
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
APIC Mode
MPS Version Control For OS
OS Select For DRAM > 64MB
Video BIOS Shadow
Full Screen LOGO Show
Summary Screen Show
: Move
Enter: Select
F5: Previous Values
[Press Enter]
[Press Enter]
[Disabled]
[Enabled]
[USB-FDD]
[Hard Disk]
[LS120]
[Enabled]
[On]
[Enabled]
[30]
[250]
[Setup]
[Enabled]
[1.4]
[Non-OS2]
[Enabled]
[Enabled]
[Enabled]
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level
ESC: Exit
F1: General Help
F7: Optimized Defaults
Virus Warning
Setting
Description
Enabled
Disabled
Turns on hard disk boot sector virus protection
Turns off hard disk boot sector virus protection
Quick Power On Self-Test
Shortens Power On Self-Test (POST) cycle to enable shorter boot up time.
Setting
Description
Enabled
Disabled
Shorten Power On Self Test (POST) cycle and bootup time
Standard Power On Self Test (POST)
Chapter 3
First/Second/Third Boot Device
Set the boot device sequence as BIOS attempts to load the disk operating
system.
Setting
Description
LS120
Hard Disk
CD-ROM
ZIP100
USB-FDD
USB-ZIP
USB-CDROM
Legacy LAN
Disabled
Boot from LS-120 drive
Boot from the HDD
Boot from CD-ROM
Boot from ATAPI ZIP drive
Boot from USB floppy drive
Boot from USB ZIP drive
Boot from USB CDROM
Boot from network drive
Disable the boot device sequence
Boot Other Device
Enables the system to boot from alternate devices if the system fails to boot
from the “First/Second/Third Boot Device” list.
Setting
Description
Enabled
Disabled
Enable alternate boot device
No alternate boot device allowed
Boot Up NumLock Status
Set the NumLock status when the system is powered on.
Setting
Description
On
Off
Forces keypad to behave as 10-key
Forces keypad to behave as arrow keys
Typematic Rate Setting
Enables “Typematic Rate” and “Typematic Delay” functions.
Settings: [Enabled, Disabled]
Typematic Rate (Chars/Sec)
This item sets the rate (characters/second) at which the system retrieves a
signal from a depressed key.
Settings: [6, 8, 10, 12, 15, 20, 24, 30]
BIOS Setup
Typematic Delay (Msec)
This item sets the delay between when the key was first pressed and when
the system begins to repeat the signal from the depressed key.
Settings: [250, 500, 750, 1000]
Security Option
Selects whether the password is required every time the System boots, or
only when you enter Setup.
Setting
Description
Setup
Password prompt appears only when end users try to run BIOS
Setup
Password prompt appears every time when the computer is
powered on and when end users try to run BIOS Setup
System
APIC Mode
Enables APIC (Advanced Programmable Interrupt Controller) functionality.
Settings: [Enabled, Disabled]
MPS Variation Control for OS
Settings: [1.1, 1.4]
OS Select For DRAM > 64MB
Select OS2 only if you are running OS/2 operating system with greater than
64MB of RAM on the system.
Settings: [Non-OS2, OS2]
Video BIOS Shadow
Enabled copies Video BIOS to shadow RAM Improves performance.
Settings: [Enabled, Disabled]
Full Screen Logo Show
Show full screen logo during BIOS boot up process.
Settings: [Enabled, Disabled]
Chapter 3
Summary Screen Show
Show summary screen.
Settings: [Enabled, Disabled]
BIOS Setup
CPU FEATURE
Phoenix - AwardBIOS CMOS Setup Utility
CPU Feature
[16 Min]
[Thermal Monitor 1]
[ 0 X]
[0.764V]
[Enabled]
[Disabled]
Deplay Prior to Thermal
Thermal Management
TM2 Bus Ratio
TM2 Bus VID
C7 CMPXCHG8
C7 NoExecute (NX)
: Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level
ESC: Exit
F1: General Help
F7: Optimized Defaults
Deplay Prior to Thermal
Settings: [4 Min, 8 Min, 16 Min, 32 Min]
Thermal Management
This item sets CPU’s thermal control rule to protect CPU from overheat.
Setting
Description
Thermal Monitor 1
Thermal Monitor 2
On-die throtting
Ratio & VID transition
TM2 Bus Ratio
This item sets the frequency (bus ratio) of the throttled performance that will
be initiated when the on die sensor goes from not hot to hot.
Key in a DEC number.
Settings: [Min = 0, Max = 255]
Chapter 3
TM2 Bus VID
This item sets the voltage of the throttled performance that will be initiated
when the on die sensor goes from not hot to hot.
Settings: [0.700V, 0.716V, 0.732V, 0.748V, 0.764V, 0.780V, 0.796V, 0.812V,
0.828V, 0.844V, 0.860V, 0.876V, 0.892V, 0.908V, 0.924V, 0.940V, 0.956V,
0.972V, 0.988V, 1.004V, 1.020V, 1.036V, 1.052V, 1.068V, 1.084V, 1.100V,
1.116V, 1.132V, 1.148V, 1.164V, 1.180V, 1.196V, 1.212V, 1.228V, 1.244V,
1.260V, 1.276V, 1.292V, 1.308V, 1.324V, 1.340V, 1.356V, 1.372V, 1.388V,
1.404V, 1.420V, 1.436V, 1.452V, 1.468V, 1.484V, 1.500V, 1.516V, 1.532V,
1.548V, 1.564V, 1.580V, 1.596V, 1.612V, 1.628V, 1.644V, 1.660V, 1.676V,
1.692V, 1.708]
C7 CMPXCHG8
Settings: [Enabled, Disabled]
C7 NoExecute (NX)
Settings: [Enabled, Disabled]
BIOS Setup
HARD DISK BOOT PRIORITY
Phoenix - AwardBIOS CMOS Setup Utility
Hard Disk Boot Priority
1.
2.
3.
4.
5.
6.
7.
8.
Pri. Master :
Pri. Slave :
Sec. Master :
Sec. Slave :
USBHDD0 :
USBHDD1 :
USBHDD2 :
Bootable Add-In Cards
PU/PD/+/-:Change Priority
: Move
F5: Previous Values
F6: Fail-Safe Defaults
Item Help
Menu Level
Use < > or < > to
select a device, then
press < + > to move it
up, or < - > to move it
down the list. Press
<ESC> to exit this
menu.
ESC: Exit
F10: Save
F7: Optimized Defaults
This is for setting the priority of the hard disk boot order when the “Hard
Disk” option is selected in the “[First/Second/Third] Boot Device” menu item.
Chapter 3
ADVANCED CHIPSET FEATURES
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
AGP & P2P Bridge Control
CPU & PCI Bus Control
Memory Hole
System BIOS Cacheable
Video RAM Cacheable
Init Display First
[Press Enter]
[Press Enter]
[Disabled]
[Enabled]
[Disabled]
[PCI Slot]
Select Display Device
Panel Type
[CRT]
[02]
: Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
Item Help
Menu Level
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
WARNING: The Advanced Chipset Features menu is used for
optimizing the chipset functions. Do not change these settings unless
you are familiar with the chipset.
Memory Hole
Settings: [Disabled, 15M – 16M]
System BIOS Cacheable
Settings: [Disabled, Enabled]
Video RAM Cacheable
Settings: [Disabled, Enabled]
Init Display First
Settings: [PCI Slot, AGP]
BIOS Setup
Select Display Device
This setting refers to the type of display being used with the system.
Settings: [CRT, LCD, CRT+LCD]
Panel Type
This setting refers to the native resolution of the display being used with the
system.
Key in a HEX number.
Settings: [Min = 0000, Max = 000F]
Chapter 3
AGP & P2P BRIDGE CONTROL
Phoenix - AwardBIOS CMOS Setup Utility
AGP & P2P Bridge Control
AGP Aperture Size
AGP 2.0 Mode
AGP Driving Control
x AGP Driving Value
AGP Fast Write
AGP Master 1 WS Write
AGP Master 1 WS Read
AGP 3.0 Calibration cycle
VGA Share Memory Size
Direct Frame Buffer
: Move
Enter: Select
F5: Previous Values
[128M]
[4x]
[Auto]
02
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[64M]
[Enabled]
+/-/PU/PD: Value
Item Help
Menu Level
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
AGP Aperture Size
This setting controls how much memory space can be allocated to AGP for
video purposes. The aperture is a portion of the PCI memory address range
dedicated to graphics memory address space.
Host cycles that hit the
aperture range are forwarded to the AGP without any translation.
Settings: [32MB, 64MB, 128MB, 256MB, 512MB, 1G]
AGP 2.0 Mode
This mainboard supports the AGP 4x interface. When the AGP 4x video card
is used, it can transfer video data at 1066MB/s. AGP 4x is backward
compatible, leave the default 4x mode on. AGP 4x mode can be detected
automatically once you plug in the AGP 4x card.
Settings: [4x, 2x, 1x]
BIOS Setup
AGP Driving Control
This item is used to signal driving current on AGP cards to auto or manual.
Settings: [Auto, Manual]
AGP Fast Write
This item is used to enable or disable the caching of display data for the
video memory of the processor.
Settings: [Enabled, Disabled]
AGP Master 1 WS Write
Settings:[Enabled, Disabled]
AGP Master 1 WS Read
Settings:[Enabled, Disabled]
AGP 3.0 Calibration Cycle
Settings: [Enabled, Disabled]
VGA Share Memory Size
Settings: [Disabled, 32M, 64M, 128M]
Direct Frame Buffer
Settings: [Enabled, Disabled]
Chapter 3
CPU & PCI BUS CONTROL
Phoenix - AwardBIOS CMOS Setup Utility
CPU & PCI Bus Control
PCI Master 0 WS Write
PCI Delay Transaction
DRDY_Timing
: Move
Enter: Select
[Enabled]
[Enabled]
[Optimize]
+/-/PU/PD: Value
F5: Previous Values
Item Help
Menu Level
F10: Save
F6: Fail-Safe Defaults
PCI Master 0 WS Write
Settings: [Enabled, Disabled]
PCI Delay Transaction
Settings: [Enabled, Disabled]
DRDY_Timing
Settings: [Slowest, Default, Optimize]
ESC: Exit
F1: General Help
F7: Optimized Defaults
BIOS Setup
INTEGRATED PERIPHERALS
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
VIA OnChip PCI Device
SuperIO Device
WatchDog support
WatchDog Timer Select
WatchDog Count value
Onboard Serial Port 1
Onboard Serial Port 2
USB Device Setting
: Move
Enter: Select
[Press Enter]
[Press Enter]
[Enable]
[Second]
[ 0]
[3F8 / IRQ4]
[2F8 / IRQ3]
[Press Enter]
+/-/PU/PD: Value
F5: Previous Values
Item Help
Menu Level
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
WatchDog support
Settings: [Enabled, Disabled]
WatchDog Timer Select
Settings: [Minute, Second]
WatchDog Count Value
Key in a DEC number.
Settings: [Min = 0, Max = 255]
Onboard Serial Port 1
Settings: [Disabled, 3F8 / IRQ4, 2F8 / IRQ3, 3E8 / IRQ4, 2E8 / IRQ3, Auto]
Onboard Serial Port 2
Settings: [Disabled, 3F8 / IRQ4, 2F8 / IRQ3, 3E8 / IRQ4, 2E8 / IRQ3, Auto]
Chapter 3
VIA ONCHIP PCI DEVICE
Phoenix - AwardBIOS CMOS Setup Utility
VIA OnChip PCI Device
Azalia HDA Controller
OnBoard LAN Boot ROM
[Auto]
[Disabled]
Item Help
Menu Level
: Move
Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Azalia HAD Controller
Settings:[Auto, Disabled]
OnBoard LAN Boot ROM
Settings:[Enabled, Disabled]
ESC: Exit
F1: General Help
F7: Optimized Defaults
BIOS Setup
USB DEVICE SETTING
Phoenix - AwardBIOS CMOS Setup Utility
USB Device Setting
USB 1.0 Controller
USB 2.0 Controller
USB Operation Mode
USB Keyboard Function
USB Storage Function
[Enabled]
[Enabled]
[High Speed]
[Enabled]
[Enabled]
*** USB Mass Storage Device Boot Setting ***
UFDDA
USB Floppy
UFDDB
USB Floppy
No Device
[Auto mode]
No Device
[Auto mode]
No Device
[Auto mode]
No Device
[Auto mode]
No Device
[Auto mode]
No Device
[Auto mode]
No Device
[Auto mode]
No Device
[Auto mode]
: Move
Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level
[Enable] or [Disable]
Universal Host
Controller
Interface for Universal
Serial Bus
ESC: Exit
F1: General Help
F7: Optimized Defaults
USB 1.0 Controller
Enable or disable Universal Host Controller Interface for Universal Serial Bus.
Settings: [Enabled, Disabled]
USB 2.0 Controller
Enable or disable Enhanced Host Controller Interface for Universal Serial Bus.
Settings: [Enabled, Disabled]
USB Operation Mode
Auto decide USB device operation mode.
Setting
Description
High Speed
If USB device was high speed device, then it operated on high
speed mode. If USB device was full/low speed device, then it
operated on full/low speed mode.
All of USB Device operated on full/low speed mode
Full/Low Speed
Chapter 3
USB Keyboard Function
Enable or disable Legacy support of USB Keyboard
Settings: [Enabled, Disabled]
USB Storage Function
Enable or disable Legacy support of USB Mass Storage
Settings: [Enabled, Disabled]
No Device
Setting
Description
Auto mode
FDD mode
HDD mode
According to contents of USB MSD decide boot up type.
The USB MSD always boot up as floppy disk.
The USB MSD always boot up as hard disc.
BIOS Setup
POWER MANAGEMENT SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Suspend Type
Power Management Option
HDD Power Down
Suspend Mode
Video Off Option
Video Off Method
MODEM Use IRQ
Soft-Off by PWRBTN
Run VGABIOS if S3 Resume
Ac Loss Auto Restart
Wakeup Event Detect
[S1&S3]
[User Define]
[Disabled]
[Disabled]
[Suspend -> Off]
[V/H SYNC+Blank]
[3]
[Instant-Off]
[Auto]
[Off]
[Press Enter]
: Move
Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level
ESC: Exit
F1: General Help
F7: Optimized Defaults
ACPI Suspend Type
Setting
Description
S1(POS)
S1/Power On Suspend (POS) is a low power state. In this state,
no system context (CPU or chipset) is lost and hardware
maintains all system contexts.
S3/Suspend To RAM (STR) is a power-down state. In this state,
power is supplied only to essential components such as main
memory and wakeup-capable devices. The system context is
saved to main memory, and context is restored from the
memory when a "wakeup" event occurs.
Depends on the OS to select S1 or S3.
S3(STR)
S1 & S3
Power Management Option
Settings: [User Define, Min Saving, Max Saving]
HDD Power Down
Sets the length of time for a period of inactivity before powering down the
hard disk.
Settings: [Disabled, 1~15(minutes)]
Suspend Mode
Settings:[Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 Min,
40 Min, 1 Hour]
Chapter 3
Video Off Option
Select whether or not to turn off the screen when system enters power
saving mode, ACPI OS such as Windows XP will override this option.
Setting
Description
Always On
Screen is always on even when system enters power saving
mode
Screen is turned off when system enters power saving mode
Suspend -> Off
Video Off Method
Settings:[Blank Screen, V/H SYNC+Blank, DPMS Support]
MODEM Use IRQ
Settings: [NA, 3, 4, 5, 7, 9, 10, 11]
Soft-Off by PWRBTN
Setting
Description
Delay 4 Sec
System is turned off if power button is pressed for more than
four seconds
Power button functions as a normal power-on/-off button
Instant-Off
Run VGABIOS if S3 Resume
Select whether to run VGA BIOS if resuming from S3 state.
This is only
necessary for older VGA drivers.
Settings: [Auto, Yes, No]
AC Loss Auto restart
The field defines how the system will respond after an AC power loss during
system operation.
Setting
Description
Off
Keeps the system in an off state until the power button is
pressed
Restarts the system when the power is back
Former-Sts
On
Former-Sts
BIOS Setup
WAKEUP EVENT DETECT
Phoenix - AwardBIOS CMOS Setup Utility
Wakeup Event Detect
[Hot Key]
[Any Key]
[Any Botton]
[Disabled]
[Disabled]
[By OS]
[By OS]
[Disabled]
0
0: 0: 0
PS2KB Wakeup Select
PS2KB Wakeup Key Select
PS2MS Wakeup Key Select
PS2 Keyboard Power On
PS2 Mouse Power On
PowerOn by PCI Card
Wake Up On LAN/Ring
RTC Alarm Resume
Date (of Month)
Resume Time (hh:mm:ss)
: Move
Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level
When Select Password,
Please press ENTER key
to change Password
Max 8 numbers.
ESC: Exit
F1: General Help
F7: Optimized Defaults
PS2KB Wakeup Select
When selecting Password, press Enter to change password. The maximum
number of characters is eight.
Settings: [Hot Key, Password]
PS2KB Wakeup Key Select
Sets a Hot Key to restore the system from the power saving mode to an
active state.
Settings: [Ctrl+F1, Ctrl+F2, Ctrl+F3, Ctrl+F4, Ctrl+F5, Ctrl+F6, Ctrl+F7,
Ctrl+F8, Ctrl+F9, Ctrl+F10, Ctrl+F11, Ctrl+F12, Power, Wake, Any Key]
PS2MS Wakeup Key Select
Enables any mouse activity to restore the system from the power saving
mode to an active state.
Settings: [Any Botton, Left Botton, Right Botton]
Chapter 3
PS2 Keyboard Power On
Settings: [Disabled, Enabled]
PS2 Mouse Power On
Settings: [Disabled, Enabled]
PowerOn by PCI Card
Enables activity detected from any PCI card to power up the system or
resume from a suspended state. Such PCI cards include LAN, onboard USB
ports, etc.
Settings: [By OS, Enabled]
Wake Up On LAN/Ring
Settings: [By OS, Enabled]
RTC Alarm Resume
Sets a scheduled time and/or date to automatically power on the system.
Settings: [Disabled, Enabled]
Date (of Month)
The field specifies the date for “RTC Alarm Resume”.
Resume Time (hh:mm:ss)
The field specifies the time for “RTC Alarm Resume”.
BIOS Setup
PNP/PCI CONFIGURATIONS
Phoenix - AwardBIOS CMOS Setup Utility
PnP / PCI Configurations
PNP OS Installed
Reset Configuration Data
[No]
[Disabled]
Item Help
Menu Level
Resources Controlled By
x IRQ Resources
[Auto(ESCD)]
Press Enter
PCI/VGA Palette Snoop
Assign IRQ For VGA
Assign IRQ For USB
[Disabled]
[Enabled]
[Enabled]
** PCI Express relative items **
Maximum ASPM supported
Maximum Payload Size
[L0s&L1]
[4096]
: Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
NOTE:
Select Yes if you are
using a Plug and Play
capable operating
system. Select No if
you need the BIOS to
configure non-boot
devices
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
This section covers some very technical items and it is
strongly recommended to leave the default settings as is unless you
are an experienced user.
PNP OS Installed
Setting
Description
Yes
BIOS will only initialize the PnP cards used for booting (VGA,
IDE, SCSI). The rest of the cards will be initialized by the
PnP operating system
BIOS will initialize all the PnP cards
No
Reset Configuration Data
This field should usually be left “Disabled”.
Setting
Description
Enabled
Resets the ESCD (Extended System Configuration Data)
after exiting BIOS Setup if a newly installed PCI card or the
system configuration prevents the operating system from
loading
Default setting
Disabled
Chapter 3
Resource Controlled By
Enables the BIOS to automatically configure all the Plug-and-Play compatible
devices.
Setting
Description
Auto(ESCD)
BIOS will automatically assign IRQ, DMA and memory base
address fields
Unlocks “IRQ Resources” for manual configuration
Manual
PCI/VGA Palette Snoop
Settings: [Disabled, Enabled]
Assign IRQ For VGA/USB
Assign IRQ for VGA and USB devices.
Settings: [Disabled, Enabled]
Maximum ASPM supported
Control maximum level of ASPM supported on the given PCI Express links on
the system.
Settings: [L0, L0s, L1, L0s&L1]
Maximum Payload Size
Set maximum TLP payload size for the PCI Express devices. The unit is byte.
Settings: [128, 256, 512, 1024, 2048, 4096]
BIOS Setup
PC HEALTH STATUS
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
CPU Temp.
+ 5V
CPU Vcore
3.3V
+12V
: Move
Enter: Select
F5: Previous Values
Item Help
Menu Level
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
The PC Health Status displays the current status of all of the monitored
hardware devices/components such as CPU voltages, temperatures and fan
speeds.
Chapter 3
FREQUENCY / VOLTAGE CONTROL
Phoenix - AwardBIOS CMOS Setup Utility
Frequency / Voltage Control
DRAM Clock/Drive Control
Auto Detect PCI Clk
Spread Spectrum
: Move
Enter: Select
F5: Previous Values
[Press Enter]
[Enabled]
[0.20%]
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
Item Help
Menu Level
ESC: Exit
F1: General Help
F7: Optimized Defaults
Auto Detect PCI Clk
Settings: [Disabled, Enabled]
Spread Spectrum
When the mainboard's clock generator pulses, the extreme values (spikes) of
the pulses create EMI (Electromagnetic Interference). The Spread Spectrum
function reduces the EMI generated by modulating the pulses so that the
spikes of the pulses are reduced to flatter curves.
Settings: [Disabled, 0.20%, 0.25%, 0.35%]
BIOS Setup
DRAM CLOCK/DRIVE CONTROL
Phoenix - AwardBIOS CMOS Setup Utility
PnP / PCI Configurations
DRAM Clock
DRAM Timing
SDRAM CAS Latency [DDR/DDR2]
Bank Interleave
Precharge to Active(Trp)
Active to Precharge(Tras)
Active to CMD(Trcd)
REF to ACT/REF (Trfc)
ACT(0) to ACT(1) (TRRD)
Read to Precharge (Trtp)
Write to read CMD (Twtr)
Write Recovery Time (Twr)
RDSAIT mode
x RDSAIT selection
: Move
Enter: Select
[By SPD]
[Manual]
[2.5 / 4]
[Disabled]
[4T]
[07T]
[4T]
[25T]
[3T]
[2T]
[1T/2T]
[4T]
[Auto]
03
+/-/PU/PD: Value
F5: Previous Values
Item Help
Menu Level
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
DRAM Clock
The chipset supports synchronous and asynchronous mode between host
clock and DRAM clock frequency.
Settings: [By SPD, 100 MHz, 133 MHz, 166 MHz, 200MHz, 266MHz, 333MHz]
DRAM Timing
The value in this field depends on the memory modules installed in your
system. Changing the value from the factory setting is not recommended
unless you install new memory that has a different performance rating than
the original modules.
Settings: [Manual, Auto By SPD]
SDRAM CAS Latency [DDR/DDR2]
Settings: [1.5/2, 2/3, 2.5/4, 3/5]
Bank Interleave
Settings: [Disabled, 2 Bank, 4 Bank, 8 Bank]
Precharge to Active (Trp)
Settings: [2T, 3T, 4T, 5T]
Chapter 3
Active to Precharge (Tras)
Settings: [05T ~ 20T]
Active to CMD (Trcd)
Settings: [2T, 3T, 4T, 5T]
REF to ACT/REF (Trfc)
Settings: [8T ~ 71T]
ACT(0) to ACT(1) (TRRD)
Settings: [2T, 3T, 4T, 5T]
Read to Precharge (Trtp)
Settings: [2T, 3T]
Write to Read CMD (Twtr)
Settings: [1T/2T, 2T/3T]
Write Recovery Time (Twr)
Settings: [2T, 3T, 4T, 5T]
RDSAIT mode
Settings: [Auto, Manual]
BIOS Setup
LOAD FAIL-SAFE DEFAULTS
Phoenix - AwardBIOS CMOS Setup Utility
Frequency / Voltage Control
Standard CMOS Features
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Set User Password
Power Management Setup
PnP / PCI Configurations
&N
Exit Setup
Load Fail-Safe DefaultsSave
(Y/N)?
PC Health Status
Esc : Quit
Exit Without Saving
F9 : Menu in BIOS
: Select Item
F10 : Save & Exit Setup
Load Fail-Safe Defaults
This option is for restoring all the default fail-safe BIOS settings.
These
values are set by the mainboard manufacturer to provide a stable system with
basic performance.
Entering “Y” loads the default fail-safe BIOS values.
Chapter 3
LOAD OPTIMIZED DEFAULTS
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency / Voltage Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
PnP / PCI Configurations
Set User Password
&NExit Setup
Load Optimized DefaultsSave
(Y/N)?
PC Health Status
Esc : Quit
Exit Without Saving
F9 : Menu in BIOS
: Select Item
F10 : Save & Exit Setup
Load Optimized Defaults
This option is for restoring all the default optimized BIOS settings.
The
default optimized values are set by the mainboard manufacturer to provide a
stable system with optimized performance.
Entering “Y” loads the default optimized BIOS values.
BIOS Setup
SET SUPERVISOR / USER PASSWORD
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency / Voltage Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP / PCI Configurations Enter Password:
Save & Exit Setup
PC Health Status
Exit Without Saving
Esc : Quit
F9 : Menu in BIOS
: Select Item
F10 : Save & Exit Setup
Change / Set / Disable Password
This option is for setting a password for entering BIOS Setup.
When a
password has been set, a password prompt will be displayed whenever BIOS
Setup is run. This prevents an unauthorized person from changing any part
of your system configuration.
There are two types of passwords you can set. A supervisor password and a
user password.
When a supervisor password is used, the BIOS Setup
program can be accessed and the BIOS settings can be changed. When a
user password is used, the BIOS Setup program can be accessed but the
BIOS settings cannot be changed.
To set the password, type the password (up to eight characters in length)
and press <Enter>. The password typed now will clear any previously set
password from CMOS memory. The new password will need to be reentered
to be confirmed. To cancel the process press <Esc>.
To disable the password, press <Enter> when prompted to enter a new
password. A message will show up to confirm disabling the password. To
cancel the process press <Esc>.
Chapter 3
Additionally, when a password is enabled, the BIOS can be set to request the
password each time the system is booted. This would prevent unauthorized
use of the system. See “Security Option” in the “Advanced BIOS Features”
section for more details.
BIOS Setup
SAVE & EXIT SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency / Voltage Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP / PCI Configurations
&NExit Setup
SAVE to CMOS & EXIT Save
(Y/N)?
PC Health Status
Esc : Quit
Exit Without Saving
F9 : Menu in BIOS
: Select Item
F10 : Save & Exit Setup
Save Data to CMOS
Entering “Y” saves any changes made and exits the program.
Entering “N” will cancel the exit request.
Chapter 3
EXIT WITHOUT SAVING
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency / Voltage Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Set User Password
Power Management Setup
PnP / PCI Configurations
Save &
N Exit Setup
Quit Without Saving (Y/N)?
PC Health Status
Esc : Quit
Exit Without Saving
F9 : Menu in BIOS
: Select Item
F10 : Save & Exit Setup
Abandon all Data
Entering “Y” discards any changes made and exits the program.
Entering “N” will cancel the exit request.
CHAPTER 4
Driver Installation
This chapter gives you brief descriptions of each mainboard driver and
application. You must install the VIA chipset drivers first before
installing other drivers such as audio or VGA drivers. The applications
will only function correctly if the necessary drivers are already
installed.
Chapter 4
DRIVER UTILITIES
Getting Started
The Driver Utilities CD contains the driver utilities and software for enhancing
the performance of the mainboard.
Note: The driver utilities and software are updated from time to time. The latest
updated versions are available at http://www.viaembedded.com./
Driver Installation
Running the Driver Utilities CD
To start using the CD, insert the CD into the CD-ROM or DVD-ROM drive.
The CD should run automatically after closing the CD-ROM or DVD-ROM drive.
The driver utilities and software menu screen should then appear on the
screen. If the CD does not run automatically, click on the “Start” button and
select “Run…” Then type: "D:\Setup.exe".
NOTE: D: might not be the drive letter of the CD-ROM/DVD-ROM in
your system.
Chapter 4
CD CONTENT
VIA 4in1 Drivers: Contains VIA ATAPI Vendor Support
Driver (enables the performance enhancing bus mastering
functions on ATA-capable Hard Disk Drives and ensures IDE
device compatibility), AGP VxD Driver (provides service routines
to your VGA driver and interface directly to hardware, providing
fast graphical access), IRQ Routing Miniport Driver (sets the
system's PCI IRQ routing sequence) and VIA INF Driver
(enables the VIA Power Management function).
VIA Graphics Driver: Enhances the onboard VIA graphic
chip.
VIA Audio Driver: Enhances the onboard VIA audio chip.
VIA USB 2.0 Driver: Enhances VIA USB 2.0 ports.
VIA LAN Driver: Enhances the onboard VIA 10/100M LAN
chip.
VIA RAID Driver: Support for SATA RAID devices.
Note:
EPIA-NR does not support video outputs of HDTV (YPbPr) and LCD.
Please DO NOT enable these functions in this system.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement