Quick Installation Guide 1000Base-T to 1000Base-SX/LX Gigabit Ethernet

Quick Installation Guide 1000Base-T to 1000Base-SX/LX Gigabit Ethernet
1000Base-T to 1000Base-SX/LX
Gigabit Ethernet
Media Converter
Quick Installation Guide
FCC Class A Certification
This equipment has been tested and found to comply with
the regulations for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when
the
equipment
is
operated
in
a
commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with this user’s guide, may cause
harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference, in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the
user may be required to take adequate measures.
VCCI Class A Compliance (Japan)
This is a product of VCCI Class A Compliance
2
Introduction
Thank you for choosing the 1000Base Gigabit Ethernet
Media Converter, The Converter introduced here
provides one channel media conversion between
1000BASE-TX and 1000BASE-SX/LX.
About Media Converter
Media Converter is a network technology specified by
IEEE 802.3ab and IEEE 802.3z 1000BASE-TX and
1000BASE-SX/LX standards.
3
Product Features









One-channel media conversion between
1000BASE-TX and 1000BASE-SX/LX
Fiber media allows: multi-mode fiber and
single-mode fiber using SC connector
Link Pass Through function
Auto negotiation of duplex mode on TX port
Auto MDI/MDI-X for TX port
Full wire-speed forwarding rate
Front panel status LEDs
Used as a stand-alone device or with a chassis
Hot-swappable when used with a chassis
4
Installation
This chapter gives step-by-step installation instructions
for the Converter.
Selecting a Site for the Equipment
As with any electric device, you should place the
equipment where it will not be subjected to extreme
temperatures, humidity, or electromagnetic interference.
Specifically, the site you select should meet the
following requirements:
1.
2.
3.
4.
5.
The ambient temperature should be between 32
and 104 degrees Fahrenheit (0 to 40 degrees
Celsius).
The relative humidity should be less than 90
percent, non-condensing.
Surrounding electrical devices should not exceed
the electromagnetic field (RFC) standards for
IEC 801-3, Level 2 (3V/M) field strength.
Make sure that the equipment receives adequate
ventilation. Do not block the ventilation holes on
each side of the switch or the fan exhaust port on
the side or rear of the equipment.
The power outlet should be within 1.8 meters of
the switch.
5
Connecting to Power
1.
2.
This Converter is a plug-and-play device.
Connect the supplied AC to DC power adaptor
with a power voltage of 7.5Vdc/1.5Amp to the
DC-Jack on the converter, and then attach the
plug into a standard AC outlet.
Installing in a Chassis
The Converter can be fit into any of the expansion slots
on a special designed chassis.
 First, install the converter onto a carrier supplied with
the chassis:
Step 1Unscrew and pull out the media converter
board.
Step 2Plug in the media board to any of the vacant
slot.
Step 3Fit the converter onto the carrier and use the
screw to secure it.
6
Monitoring the Converter through
Management Module
There is a management module that can control this
media converter through the chassis system, this media
converter can be controlled through Web Browser,
SNMP and terminal emulation program.
The management module will detect the default reset
on the DIP switches and display out the status, also the
management module can control the function through
the chassis system.
NOTE: To control the function in a working station, need to collocate
together with optional Chassis System and Management Module.
7
LED Indicator
The LED indicators give you instant feedback on status
of the converter:
LEDs
Power
(PWR)
Link and
Activity
(LINK/ACT)
State
Lights on
Lights off
Lights on
Lights Blinking
Lights off
Indication
Power on
Power off
Linking
Data transmitting and receiving
Not Linking
8
Link Pass Through Function
LLCF (Link Loss Carry Forward)
When a device connected to the converter and the TP
line loss the link, the converter’s fiber will disconnect
the link of transmit, so that the other ends will know that
there is a linkage error on this end. And when the Fiber
line loss the link, the converter’s TP will disconnected,
and the other end will know that there is linkage
problem exist.
There is a default LLCF setting on this converter.
The table below shows how LLCF function is working:
M e dia
Co nv er te r A
Fibe r
TX R X
M e dia
Co nv er te r B
L INK 3
L INK 2
C o ppe r
C o ppe r
Fibe r
TX R X
Cab le 5
Cab le 1
Cab le 3
Cab le 2
R X TX
LINK 1
LINK 4
Gig abit Sw itc h
Cab le 4
R X TX
Gigabit Sw itc h
Link Status
Disconnect
Cable 1
Cable 2
Cable 3
Cable 4
Cable 5
Link 1
Link 2
Link 3
Link 4
Off
Off
On
Off
Off
On
Off
On
Off
Off
On
Off
On
Off
Off
On
Off
Off
Off
Off
9
LLR (Link Loss Return)
When a device connected to the converter and the fiber
line loss the link, the converter’s fiber will disconnect
the link of transmit.
There is a switch to enable or disable the function of the
media converter.
The table below shows how LLR function is working:
Media Converter
A
B
LLR
ON
OFF
Me dia
Co nve rte r B
Me dia
Co nve rte r A
L INK 2
C o pper
Auto-Negotiation
OFF
OFF
Fibe r
Fibe r
TX R X
TX R X
LINK 1
C oppe r
Cab le 1
Cab le 2
Cab le 3
C o ppe r
Cab le 4
LINK 3
LINK 4
Gigabit Switc h
C o ppe r
Gigabit Sw itc h
Link Status
Disconnect
Link 1
Link 2
Link 3
Link 4
Cable 1
Off
Off
Off
Off
Cable 2
Off
On
On
Off
Cable 3
Off
Off
Off
Off
Cable 4
Off
Off
Off
Off
NOTE: If connecting two converters with LLR function in both end, it is
recommended that the monitor end converter had to turn off the LLR
function, and turn on the LLR function of the remote end converter.
10
12
on
on
12
Switch 1 : On -> Forced Mode
Off -> Auto Negotiation mode
Switch 2 : On -> LLR enable
Off -> LLR disable
Switch
There is a two pin DIP switch on the module which
define as switch 1 and switch 2:
Switch 1: Fiber mode switch
When the switch was turned to “On”, it means that
the fiber was turned to forced mode, and “Off” for
auto-negotiation mode.
Note: Be sure the opposite end is using the same setting (forced or Auto-negotiation). And
when using two converters at the same time, the two converters MUST set to forced
mode.
Switch 2: LLR
When the switch was turned to “On”, it means that
the LLR was enabled and “Off” for disabled.
Note: When using two converters, don’t enable the both device’s LLR function at the
same time.
11
Specifications
Standards:
Data Transfer Rate:
Duplex Mode:
LED indicators:
Cable
Dimensions
Weight
Power
Media Interface:
EMI Compatiblity:
IEEE802.3ab 1000BASE-TX
IEEE802.3z 1000BASE-SX/LX
1488000pps for 1000Mbps
Full Duplex Mode
PWR, LNK/ACT
1000BASE-T -4 pair Cat. 5, EIA/TIA-568 100-ohm screened
twisted-pair (STP), up to 100m
1000BASE-SX -50/125μm multi-mode fiber optic cable, up to
550m
1000BASE-LX -9/125μm or 10/125μm single-mode fiber optic
cable, up to 70km
L120 × W88 × H25 mm
300 g
External power adaptor 5V 1.5A or 5V/1A
RJ-45, SC
FCC Class A
CE Certification, Class A
VCCI Class A
Temperture:
Storage: -10C ~ 70C
Humidity:
Power Consumption:
Operating: 0C ~ 40C
10% ~90% non-condensing
2.7 Watts (maximum)
12
Ordering Information
Please include the following information when ordering:
1. Fiber type: multi-mode or single-mode
2. Fiber connector type: SC
3. Segment distance range for the fiber port
TX port
Connector
Type
RJ-45
FX port
Connector
Type
SC
SC
SC
SC
Cabling
Segment Distance
Copper Wire
Max. 100 m
Cabling
Segment Distance
Multi-Mode Fiber
Single-Mode Fiber
Single-Mode Fiber
Single-Mode Fiber
Max. 550 m
Max. 20 km
Max. 50 km
Max. 70 km
P/N: 29071500MC10010
Rev:C1-01
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement