IB710 USER’S MANUAL Socket 370 Little Board

IB710 USER’S  MANUAL Socket 370 Little Board
IB710
Socket 370 Little Board
With VGA/Audio/LAN
USER’S MANUAL
Version 1.0B
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 are trademarks of International Business Machines
Corporation.
Intel and Celeron are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
IB710 User’s Manual
Table of Contents
Introduction...............................................................1
Installations ..............................................................5
Installing the CPU........................................................... 6
Installing the Memory (DIMM) ....................................... 7
Setting the Jumpers ....................................................... 8
Connectors on IB710 .................................................. 14
Watchdog Timer Configuration................................... 29
BIOS Setup..............................................................31
VGA Drivers Installation ........................................54
Audio Drivers Installation ......................................58
LAN Drivers Installation.........................................62
Appendix .................................................................66
A. POST Codes .......................................................67
B. I/O Port Address Map..........................................73
C. Interrupt Request Lines (IRQ)..............................72
IB710 User’s Manual
iii
This page was intentionally left blank.
iv
IB710 User’s Manual
INTRODUCTION
Introduction
Product Description
The IB710 little board is a high-performance multimedia Little Board
based on the Intel 440BX AGPset. It features a Socket 370 architecture
that supports Intel Celeron and Coppermine processors using 66MHz and
100MHz front side bus respectively.
The IB710 packs all the functions of a versatile system, including VGA,
Audio, Ethernet and Hardware Monitoring features, into the Little Board
form factor. System memory is provided by one DIMM socket that
accommodates up to 256MB SDRAM.
The Award BIOS facilitates easy system configuration and peripheral
setup. Other advanced features include DiskOnChip flash disk support,
watchdog timer, PC/104, USB and IrDA interface.
DiskOnChip flash disks are storage devices that has no moving parts and
emulates FDD/HDD with Flash/RAM/ROM offering reliable
data/program storage and long life span. They are reliable and suitable for
industrial or other harsh environments characterized by motion, shock,
vibration, adverse temperature, dust and humidity. Other features include
faster data access, longer MTBF, lower power consumption, cost
effective for small capacity and small form factor.
PC/104 is an ISA interface that supports compact-form-factor PC/104
modules (3.6” x 3.8”). It supports self-stacking and pin-and-socket
connector. PC/104 features a standard form factor for Embedded
applications. It is reliable, small in size and has low power consumption.
Flexible mechanical configurations can be attained with PC/104.
Modules support various functions such as display, audio, digital I/O,
GPS, PCMCIA, fax/modem, Ethernet, SCSI, RS-232/422/485 and SSD.
IB710 User’s Manual
1
INTRODUCTION
Checklist
Your IB710 package should include the items listed below. Damaged or
missing items should be reported to your supplier.
• The IB710 Embedded Little Board
• This User’s Manual
• One compact disc containing the following:
• Intel PCI IDE Driver and Flash Memory Utility
• CHIPS C&T 69000 VGA Driver
• Realtek RTL8139 Ethernet Drivers
• ESS Solo-1 ES1938S Audio Drivers
• Optional cables such as:
• 1 Floppy Ribbon Cable
• 1 Audio Cable
• 1 44-pin IDE Ribbon Cable
• 1 COM Port Cable
• 1 Printer Port Cable
• 1 PS/2 Keyboard/Mouse Cable
• 1 VGA Cable
• 1 RJ45 LAN Cable
2
IB710 User’s Manual
INTRODUCTION
Specifications
Processor
Supported
Chipset
BIOS
Socket 370 support Intel Celeron / Coppermine,
300MHz~800MHz, 66MHz/100MHz Bus Speed
Intel 440BX AGPset
Award BIOS
Supports ACPI, DMI, PnP
System Memory 1x DIMM socket support up to 256MB capacity
3.3V supported
ECC supported
Multi I/O Chipset Winbond 83977TF and 83877TF (keyboard controller is
built-in 83977TF)
I/O Features
1x FDD (up to 2.88MB, 3 Mode, LS120)
1x Parallel Port (EPP, ECP Port)
4x Serial Ports (3x RS232, 1x RS232/422/485)
1x IrDA TX/RX Headers
Bus Master IDE 2x IDE interfaces for up to 4 devices; supports PIO Mode
3/4 or Ultra DMA/33 IDE HDD, and ATAPI CD-ROM
On-board VGA
CHIPS 69000 PCI VGA Accelerator
Support CRT & LCD Panels
15-pin VGA connector
1024x768(High Color) resolution
2MB integrated memory
PC97 and PC98 Compatible
On-board Audio ESS Solo-1 (ESS1938S) PCI Single Audio Chip
Provides high-quality audio processing
On-board
Realtek RTL8139 Single-Chip Controller
Ethernet
32-bit performance, PCI bus master capability
Supports 10/100Mbps data transfer rates
Hardware
Winbond W83781D IC
Monitoring
Monitors CPU/system temperature and voltages
SSD Interface
Support M-Systems 2MB~144MB DiskOnChip flash disk
Watchdog Timer 16 levels
Form Factor
Little Board
Dimensions
203mm x 146mm (7.99” x 5.75”)
IB710 User’s Manual
3
INTRODUCTION
Board Dimensions
4
IB710 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the IB710 in order to set up a workable system. The topics
covered are:
Installing the CPU.............................................................6
Installing the Memory (DIMM) .........................................7
Setting the Jumpers...........................................................8
Connectors on the IB710.................................................14
Watchdog Timer Configuration.......................................29
IB710 User’s Manual
5
INSTALLATIONS
Installing the CPU
The IB710 Embedded Little Board supports a Socket 370 processor
socket for Intel Celeron/Coppermine processors.
The Socket 370 processor socket comes with a lever to secure the
processor. Raise this lever to about a 90° angle to allow the insertion of
the processor. Place the processor into the socket by making sure the
notch on the corner of the CPU corresponds with the notch on the inside
of the socket. Once the processor has slid into the socket, return the lever
to the lock position.
After you have installed the processor into the socket, check if the
jumpers for the CPU type and speed are correct.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
6
IB710 User’s Manual
INSTALLATIONS
Installing the Memory (DIMM)
The IB710 Embedded Little Board supports one 168-pin DIMM socket
for a maximum total memory of 256MB in SDRAM type. The memory
capacities supported are 32MB, 64MB, 128MB and 256MB.
Installing and Removing DIMMs
To install the DIMM, locate the memory slot on the little board and
perform the following steps:
1. Hold the DIMM so that the two keys of the DIMM align with those on
the memory slot.
2. Gently push the DIMM in an upright position until the clips of the slot
close to hold the DIMM in place when the DIMM touches the bottom
of the slot.
3. To remove the DIMM, press the clips with both hands.
Lock
DIMM
Lock
Lock
Lock
Top View of DIMM Socket
IB710 User’s Manual
7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on the IB710 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB710 and their respective functions.
Jumper Locations on IB710............................................................... 9
SW1(3): CPU Bus Speed Selector................................................... 10
SW1(5-8): CPU Frequency Selector ............................................... 10
JP2: LCD Power Setting .................................................................. 11
JP3: ATX Function Selection .......................................................... 11
JP4, JP5, JP6: RS232/RS422/RS485 (COM2) Selection ............. 11
JP7: COM3/4 RS232 +5V / +12V Power Setting ......................... 12
JP11: Onboard LAN Enable/Disable............................................... 12
JP12: DiskOnChip Address Select................................................... 12
JP13: Clear CMOS Content............................................................. 12
JP14: COM1/2 RS232 +5V / +12V Power Setting....................... 13
JP9, JP10, J9, J19: Manufacturer Testing Use ............................... 13
The following conventions are used in this section:
off off on on
↓ ↓ ↑ ↑
8
Pin 1-2
Short/Closed
IB710 User’s Manual
INSTALLATIONS
Jumper Locations on IB710
JP2: LCD Power Setting
JP7: COM3/4 RS232 +5V / +12V Power Setting
JP4, JP5, JP6: RS232/RS422/RS485 (COM2) Selection
JP3: ATX Function Selection
JP11: Onboard LAN Enable/Disable
JP12: DiskOnChip Address Select
JP13: Clear CMOS Content
JP14: COM1/2 RS232 +5V / +12V Power Setting
DISK ON CHIP
NOTE: JP9, JP10, J9, J19 are for manufacturer's testing use
IB710 User’s Manual
9
INSTALLATIONS
SW1(3): CPU Bus Speed Selector
Bus Speed
SW1(3)
Switch
Setting
100MHz
off
66MHz
on
SW1(5-8): CPU Frequency Selector
The table below shows the correct setting to match the CPU frequency.
Frequency
Multiplier
CPU
Frequency
(66MHz)
CPU
Frequency
(100MHz)
4.5X
300MHz
450MHz
SW1(5-8)
xx xx xx xx off on off on
5X
333MHz
500MHz
xx xx xx xx off off on on
5.5X
366MHz
550MHz
xx xx xx xx off off off on
6X
400MHz
600MHz
xx xx xx xx on on on off
6.5X
433MHz
650MHz
xx xx xx xx on on off off
7X
466MHz
700MHz
xx xx xx xx on off on off
7.5X
500MHz
750MHz
xx xx xx xx on off off off
8X
533MHz
800MHz
xx xx xx xx off on on off
10
IB710 User’s Manual
INSTALLATIONS
JP2: LCD Power Setting
JP2
Setting
Function
Pin 1-2
Short/Closed
3.3V
Pin 2-3
Short/Closed
5V
JP3: ATX Function Selection
JP3
Setting
Function
Pin 1-2
Short/Closed
ATX
Function
Pin 2-3
Short/Closed
Normal
JP4, JP5, JP6: RS232/RS422/RS485 (COM2) Selection
JP4, JP5, JP6
Pin Short
Function
JP4: 1-2
JP5: 3-5, 4-6
JP6: 3-5, 4-6
RS232
JP4: 3-4
JP5: 1-3, 2-4
JP6: 1-3, 2-4
RS422
JP4: 5-6
JP5: 1-3, 2-4
JP6: 1-3, 2-4
RS485
IB710 User’s Manual
11
INSTALLATIONS
JP7: COM3/4 RS232 +5V / +12V Power Setting
JP7 Pin #
Signal Name
1
JP7
Signal Name
JP7 Pin #
+5V
+5V
2
3
Pin 9 (COM3)
Pin 9 (COM4)
4
5
+12V
+12V
6
COM3 Settings: Pin 1-3 short = +5V, Pin 3-5 short = +12V
COM4 Settings: Pin 2-4 short = +5V, Pin 4-6 short = +12V
JP11: Onboard LAN Enable/Disable
JP11
Setting
LAN Function
Short/Closed
Enabled
Open
Disabled
JP12: DiskOnChip Address Select
JP12
Setting
Address
Pin 1-2
Short/Closed
D0000-D7FF
Pin 2-3
Short/Closed
D8000-DFFF
JP13: Clear CMOS Content
JP13
12
Setting
Function
Pin 1-2
Short/Closed
Normal Operation
Pin 2-3
Short/Closed
Clear CMOS Content
IB710 User’s Manual
INSTALLATIONS
JP14: COM1/2 RS232 +5V / +12V Power Setting
JP14 Pin #
Signal Name
JP14
Signal Name JP14 Pin #
1
+5V
+5V
2
3
Pin 9 (COM1)
Pin 9 (COM2)
4
5
+12V
+12V
6
COM1 Settings: Pin 1-3 short = +5V, Pin 3-5 short = +12V
COM2 Settings: Pin 2-4 short = +5V, Pin 4-6 short = +12V
JP9, JP10, J9, J19: Manufacturer Testing Use
JP9, JP10, J9, and J19 are jumpers and connectors that have no definition
in this manual and are used for manufacturer testing purposes.
IB710 User’s Manual
13
INSTALLATIONS
Connectors on IB710
The connectors on IB710 allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The following
table lists the connectors on IB710 and their respective functions.
Connector Locations on IB710........................................................ 15
P1: Peripheral Power Connector ..................................................... 16
P2: Main Power Connector.............................................................. 16
JP1: VGA CRT Connector............................................................... 16
J1: System Function Connector....................................................... 17
J2: LCD Panel Connector ................................................................ 19
Flat Panel Display Interface Pin Descriptions................................. 20
J4: Audio Connector ........................................................................ 20
J5: 18-Bit LVDS Connector (DF13-20)......................................... 21
J6: System Fan Power Connector.................................................... 21
J7: CPU Fan Power Connector........................................................ 21
J8: CD-In Audio Connector............................................................. 21
JP8: IrDA Connector........................................................................ 22
J10: Digital I/O Connector............................................................... 22
J14: Serial Ports................................................................................ 23
J12: RJ45 Connector........................................................................ 24
J13: Parallel Port Connector............................................................ 24
J15: Floppy Drive Connector........................................................... 25
J16: USB Connector......................................................................... 25
J18, J17: EIDE Connectors.............................................................. 26
J20: PS/2 Keyboard/Mouse Connector........................................... 27
CN1, CN2: PC-104 Connector ....................................................... 28
14
IB710 User’s Manual
INSTALLATIONS
Connector Locations on IB710
J1: System Function Connector
J8: CD-In Audio Connector
P2: Main Power Connector
P1: Peripheral Power Connector
JP1: VGA CRT Connector
J2: LCD Panel Connector
J5: 18-Bit LVDS Connector (DF13-20)
J4: Audio Connector
JP8: IrDA Connector
J12: RJ45 Connector
J7: CPU Fan Power Connector
System Fan Power Connector
DISK ON CHIP
J10: Digital I/O Connector
J16: USB Connector
J18, J17: EIDE Connectors
CN1, CN2: PC-104 Connector
J14: Serial Ports
J20: PS/2 Keyboard/Mouse Connector
J15: Floppy Drive Connector
J13: Parallel Port Connector
NOTE: JP9, JP10, J9, J19 are for manufacturer's testing use
IB710 User’s Manual
15
INSTALLATIONS
P1: Peripheral Power Connector
The P1 peripheral power connector has the following pin assignments.
Pin #
1
2
3
4
Signal Name
-12V
Ground
-5V
Ground
P2: Main Power Connector
The P2 main power connector has the following pin assignments.
Pin #
1
2
3
4
Signal Name
+5V
Ground
Ground
+12V
JP1: VGA CRT Connector
JP1 is a 15-pin header for an external VGA CRT female connector.
Signal Name
Red
Green
Blue
N.C.
Ground
Ground
Ground
Ground
16
Pin
1
3
5
7
9
11
13
15
Pin
2
4
6
8
10
12
14
16
IB710 User’s Manual
Signal Name
Vcc
Ground
N.C.
N.C.
H-Sync
V-Sync
N.C.
N.C.
INSTALLATIONS
J1: System Function Connector
The System Function Connector provides interfaces for light indicators
of system activities (HDD/Power) and computer status switches.
Hard Disk Drive LED
Reset Switch
Turbo LED Connector
ATX Power On Switch
Green Function
Power LED and Keylock
Speaker
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio
tone generation. An 8-ohm speaker is recommended.
Pin #
1
2
3
4
Signal Name
Speaker out
No connect
Ground
+5V
Green Function: Pins 6 and 16
This connector is for the “Green Switch” on the control
panel, which, when pressed, will force the system
immediately into the power saving (sleep) mode.
Pin #
6
16
Signal Name
Sleep
Ground
ATX Power ON Switch: Pins 7 and 17
This 2-pin connector connects to the power switch. When
pressed, the power switch will force the system to power on.
When pressed again, it will force the system to power off.
IB710 User’s Manual
17
INSTALLATIONS
Power LED and Keylock: Pins 11 - 15
The power LED indicates the status of the main power
switch. The keylock switch, when closed, will disable the
keyboard function.
Pin #
11
12
13
14
15
Signal Name
Power LED
No connect
Ground
Keylock
Ground
Turbo LED Connector: Pins 8 and 18
There is the no turbo/deturbo function on the embedded
board. The Turbo LED on the control panel will always be on
when attached to this connector.
Pin #
8
18
Signal Name
5V
Ground
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without
turning the main power switch off and then on. Orientation is
not required when making a connection to this header.
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
18
IB710 User’s Manual
INSTALLATIONS
J2: LCD Panel Connector
J2 is the pin header for flat panel LCD displays. The following shows the
pin assignments of this connector.
Signal Name
Pin # Pin # Signal Name
+12V
1
2
+12V
Ground
3
4
Ground
5V/3.3V
5
6
5V/3.3V
ENAVEE
7
8
Ground
P0
9
10
P1
P2
11
12
P3
P4
13
14
P5
P6
15
16
P7
P8
17
18
P9
P10
19
20
P11
P12
21
22
P13
P14
23
24
P15
P16
25
26
P17
P18
27
28
P19
P20
29
30
P21
P22
31
32
P23
Ground
33
34
Ground
SHFCLK
35
36
FLM
J2
MDE
37
38
LP
Ground
39
40
ENABKL
Ground
41
42
LCDVDD
DNAVDD
43
44
5V/3.3V
J2
Signal Name
P24
P26
P28
P30
P32
P34
Pin #
1
3
5
7
9
11
IB710 User’s Manual
Pin #
2
4
6
8
10
12
Signal Name
P25
P27
P29
P31
P33
P35
19
INSTALLATIONS
Flat Panel Display Interface Pin Descriptions
Pin Name
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
P31
P32
P33
P34
P35
SHFCLK
Pixels/Clk:
Color
Color
Color
Color
Color
Mono Mono Mono Color Color Color Color
SS
DD
DD
TFT
TFT
TFT TFT TFT+HR STN-SS STN-SS STN-DD STN-DD
8-bit 8-bit 16-bit 9/12/16 18/24 36-bit 18/24
8-bit
16-bit
8-bit
16-bit
24-bit
bit
bit
bit
(4bP)
(4bP)
(4bP)
(4bP)
D0
UD3 UD7
B0
B0
FB0 FB0
R1
R1
UR1
UR0
UR0
D1
UD2 UD6
B1
B1
FB1 FB1
B1
G1
UG1
UG0
UG0
D2
UD1 UD5
B2
B2
FB2 FB2
G2
B1
UB1
UB0
UB0
D3
UD0 UD4
B3
B3
FB3 FB3
B3
R2
UB2
UR1
LR0
D4
LD3
UD3
B4
B4
FB4 SB0
G4
G3
LR1
LR0
LG0
D5
LD2
UD2
G0
B5
FB5 SB1
R5
B2
LG1
LG0
LB0
D6
LD1
UD1
G1
B6
SB0 SB2
B5
R3
LB1
LB0
UR1
D7
LD0
UD0
G2
B7
SB1
B3
G3
LR2
LR1
UG1
LD7
G3
G0
SB2 FG0
B3
UG1
UB1
LD6
G4
G1
SB3 FG1
R4
UB1
LR1
LD5
G5
G2
SB4 FG2
G4
UR2
LG1
LD4
R0
G3
SB5 FG3
B4
UG2
LB1
LD3
R1
G4
FG0 SG0
R5
LG1
UR2
LD2
R2
G5
FG1 SG1
G5
LB1
UG2
LD1
R3
G6
FG2 SG2
B5
LR2
UB2
LD0
R4
G7
FG3 SG3
G6
LG2
LR2
R0
FG4 FR0
LG2
R1
FG5 FR1
LB2
R2
SG0 FR2
UR3
R3
SG1 FR3
UG3
R4
SG2 SR0
LR3
R5
SG3 SR1
LG3
R6
SG4 SR2
LB3
R7
SG5 SR3
FR0
FR1
FR2
FR3
FR4
FR5
SR0
SR1
SR2
SR3
SR4
SR5
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
8
8
16
1
1
2
2
2-2/3
5-1/3
2-2/3
5-1/3
8
P24
J4: Audio Connector
J4, a 12-pin header connector, supports an optional external connector
supporting 3 sockets for Line Out, Line In and Mic functions. The
following table shows the pin assignments of this connector.
Signal Name
Line Out R
Ground
Line In R
Ground
Mic
Ground
20
Pin #
1
3
5
7
9
11
Pin #
2
4
6
8
10
12
Signal Name
Line Out L
Ground
Line In R
Ground
BIAS
NC
IB710 User’s Manual
INSTALLATIONS
J5: 18-Bit LVDS Connector (DF13-20)
Signal Name
TX0Ground
TX15V/3.3V
NC
TX2Ground
TXC5V/3.3V
+12V
Pin #
2
4
6
8
10
12
14
16
18
20
Pin #
1
3
5
7
9
11
13
15
17
19
Signal Name
TX0+
Ground
TX1+
Ground
NC
TX2+
Ground
TXC+
ENABKL
+12V
J6: System Fan Power Connector
J6 is a 3-pin header for a CPU fan. The fan must be a 12V fan.
Pin #
1
2
3
Signal Name
Rotation
+12V
Ground
J7: CPU Fan Power Connector
J7 is a 3-pin header for a CPU fan. The fan must be a 12V fan.
Pin #
1
2
3
Signal Name
Rotation
+12V
Ground
J8: CD-In Audio Connector
Pin #
1
2
3
4
Signal Name
CD Audio L
Ground
Ground
CD Audio R
IB710 User’s Manual
21
INSTALLATIONS
JP8: IrDA Connector
This connector is used for an IrDA connector for wireless
communication.
Pin #
Signal Name
+5V IRRX IRTX
1
+5V
2
No Connect
3
Ir RX
N.C. GND
4
Ground
5
Ir TX
J10: Digital I/O Connector
This 10-pin Digital I/O connector supports TTL levels and is used to
control external devices requiring ON/OFF circuitry.
Signal Name
DI0
DI1
No Connect
No Connect
Ground
Pin #
1
2
3
4
5
Pin #
6
7
8
9
10
Signal Name
Vcc
DO0
Ground
DO1
+12V
SPECIFICATIONS:
Digital Input
Input channels: 2 bits
Input Voltage: High: 2.0V (min)
Low: 0.8V (max)
Input Load:
High: 0.05mA max at 2.7V
Low: 0.4mA max at 0.5V
Register Address: 240H
Register Format: BIT:
D1 D0
Value: DI1 DI0
Digital Output
Output channels: 2 bits
Output voltage: High: Source -0.4mA at 2.4V min
Low: Sink 8mA at 0.5V max
Register Address: 240H (Write)
Register Format: BIT:
D1
D0
Value: DO1 DO0
22
IB710 User’s Manual
INSTALLATIONS
J14: Serial Ports
J14A (COM1), J14B (COM2), J14C (COM3) and J14D (COM4/TTL
level) are the onboard serial ports on the IB710.
Pin #
Signal Name (RS-232)
1
2
3
4
5
6
7
8
9
10
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
Ground
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
No Connect.
J14B (COM2) is jumper selectable for RS-232, RS-422 and RS-485.
Pin #
RS-232
1
2
3
4
5
6
7
8
9
10
DCD
RX
TX
DTR
Ground
DSR
RTS
CTS
RI
NC
Signal Name
R2-422
RS-485
TXTX+
RX+
RXGround
RTSRTS+
CTS+
CTSNC
IB710 User’s Manual
DATADATA+
NC
NC
Ground
NC
NC
NC
NC
NC
23
INSTALLATIONS
J12: RJ45 Connector
J12, an RJ45 connector, is for the external LAN connector. The IB710
supports both 10Mbps and 100Mbps LAN facilities.
Signal Name
Pin #
Pin #
Signal Name
LED1+
RX+
LED2LED2+
TX+
1
2
3
4
5
6
7
8
9
10
LED1RXGround
Ground
TX-
J13: Parallel Port Connector
The following table describes the pin out assignments of this connector.
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Paper empty
Select
24
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
Pin #
14
15
16
17
18
19
20
21
22
23
24
25
N/A
IB710 User’s Manual
Signal Name
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
INSTALLATIONS
J15: Floppy Drive Connector
J15 of the IB710 is a 34-pin header and will support up to 2.88MB floppy
drives.
Signal Name
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
Signal Name
RM/LC
No connect
No connect
Index
Motor enable 0
Drive select 1
Drive select 0
Motor enable 1
Direction
Step
Write data
Write gate
Track 00
Write protect
Read data
Side 1 select
Diskette change
J16: USB Connector
J16 is the onboard USB pin-header that supports an external USB
connector with two ports.
Pin #
1
5
2
6
3
7
4
8
Signal Name
Vcc
USBUSB+
Ground
IB710 User’s Manual
25
INSTALLATIONS
J18, J17: EIDE Connectors
J18 is the primary IDE connector. J17 is the secondary IDE connector.
J18: IDE1
26
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
IRQ14
Address 1
Address 0
Chip select 0
Activity
Vcc
Ground
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
IB710 User’s Manual
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
Vcc
N.C.
INSTALLATIONS
J17: IDE2
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK1
MIRQ0
Address 1
Address 0
Chip select 0
Activity
Vcc
Ground
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
Vcc
N.C.
J20: PS/2 Keyboard/Mouse Connector
J20, a 10-pin header connector, has functions for both keyboard and
mouse. The following table shows the pin assignments of this connector.
Signal Name
N.C.
KB clock
KB data
Vcc
Ground
Pin #
10
9
8
7
6
Pin #
5
4
3
2
1
IB710 User’s Manual
Signal Name
N.C.
Mouse clock
Mouse data
Vcc
Ground
27
INSTALLATIONS
CON1, CON2: PC-104 Connector
CON1 and CON2 are dual-in-line pin headers that support PC-104
modules. CON1 consists of 64 pins and CON2 has 40 pins. The
following table shows the their pin assignments.
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
ZA15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
28
CON1
Signal Name Pin
IOCHK
B1
D7
B2
D6
B3
D5
B4
D4
B5
D3
B6
D2
B7
D1
B8
D0
B9
IOCHRDY
B10
AEN
B11
A19
B12
A18
B13
A17
B14
A16
B15
A15
B16
A14
B17
A13
B18
A12
B19
A11
B20
A10
B21
A9
B22
A8
B23
A7
B24
A6
B25
A5
B26
A4
B27
A3
B28
A2
B29
A1
B30
A0
B31
GND
B32
Signal Name
GND
REST
VCC
IRQ9
-5V
DRQ2
-12V
OWS
+12V
GND
SMEMW
SMEMR
IOW
IOR
DACK3
DRQ3
DACK1
DRQ1
REFRESH
CLK
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
DACK2
TC
BALE
VCC
OSC
GND
GND
Pin
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
CON2
Signal Name Pin
GND
D1
SBHE
D2
LA23
D3
LA22
D4
LA21
D5
LA20
D6
LA19
D7
LA18
D8
LA17
D9
MEMR
D10
MEMW
D11
D8
D12
D9
D13
D10
D14
D11
D15
D12
D16
D13
D17
D14
D18
D15
D19
KEY PIN
D20
IB710 User’s Manual
Signal Name
GND
MEMCS16
IOCS16
IRQ10
IRQ11
IRQ12
IRQ15
IRQ14
DACK0
DRQ0
DACK5
DRQ5
DACK6
DRQ6
DACK7
DRQ7
VCC
MASTER
GND
GND
INSTALLATIONS
Watchdog Timer Configuration
The function of the watchdog timer is to reset the system automatically
and is defined at I/O port 0443H. To enable the watchdog timer and allow
the system to reset, write I/O port 0443H. To disable the timer, write I/O
port 0441H for the system to stop the watchdog function. The timer has a
tolerance of 20% for its intervals.
The following describes how the timer should be programmed.
Enabling Watchdog:
MOV AX, 000FH (Choose the values from 0)
MOV DX, 0443H
OUT
DX, AX
Disabling Watchdog
MOV AX, 00FH (Any value is fine.)
MOV DX, 0441H
OUT
DX, AX
WATCHDOG TIMER CONTROL TABLE
Level
1
2
3
4
5
6
7
8
Value
F
E
D
C
B
A
9
8
Time/sec
0
2
4
6
8
10
12
14
Level
9
10
11
12
13
14
15
16
IB710 User’s Manual
Value
7
6
5
4
3
2
1
0
Time/sec
16
18
20
22
24
26
28
30
29
INSTALLATIONS
This page was intentionally left blank.
30
IB710 User’s Manual
BIOS SETUP
BIOS Setup
This section describes the different settings available in the Award BIOS
that comes with the IB710 embedded board. The topics covered in this
section are as follows:
BIOS Introduction ............................................................................ 32
BIOS Setup........................................................................................ 32
Standard CMOS Setup...................................................................... 34
BIOS Features Setup ........................................................................ 37
Chipset Features Setup..................................................................... 40
Power Management Setup................................................................ 43
PNP/PCI Configuration................................................................... 46
Load BIOS Defaults ......................................................................... 48
Load Setup Defaults ......................................................................... 48
Integrated Peripherals ....................................................................... 50
Supervisor / User Password............................................................. 52
IDE HDD Auto Detection................................................................ 53
Save & Exit Setup............................................................................. 53
Exit Without Saving ......................................................................... 53
IB710 User’s Manual
31
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your system’s
ROM provides critical low-level support for standard devices such as
disk drives, parallel port and serial ports. It also adds virus and password
protection, as well as special support for detailed fine-tuning of the
chipset controlling the entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you to
enter the Setup utility. If you are a little bit late pressing the <Del> key,
POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to select,
the <PgUp> and <PgDn> keys to change entries, <F1> for help and
<Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on the
screen. The Main Menu allows you to select from various setup functions
and exit choices.
32
IB710 User’s Manual
BIOS SETUP
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
ESC : Quit
F10 : Save & Exit Setup
F6 : Save CMOS to BIOS
á â à ß : Select Item
(Shift) F2 : Change Color
F7 : Load CMOS From BIOS
Time, Date, Hard Disk Type
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section that displays information
about the currently highlighted item in the list.
Note:
If your computer cannot boot after making and saving
system changes with Setup, the Award BIOS supports an
override to the CMOS settings that resets your system to its
default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum
performance and reliability. Changing the defaults could
cause the system to become unstable and crash in some
cases.
IB710 User’s Manual
33
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” allows you to record some basic hardware
configurations in your computer system and set the system clock and
error handling. If the Embedded Little Board is already installed in a
working system, you will not need to select this option. You will need to
run the Standard CMOS option, however, if you change your system
hardware configurations, the onboard battery fails, or the configuration
stored in the CMOS memory was lost or damaged.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm:dd:yy) : Thu, May 18 2000
Time (hh:mm:ss) :
00 : 00 : 00
HARD DISKS
TYPE
SIZE
CYLS
LANDZ
SECTOR
MODE
Primary Master
Primary Slave
Auto
Auto
0
0
0
0
0
0
0
0
0
0
0
0
Auto
Auto
Secondary Master
Auto
0
0
0
0
0
0
Auto
Secondary Slave
Auto
0
0
0
0
0
0
Auto
Drive A
: 1.44M, 3.5in
Drive B
: None
Video
: EGA / VGA
Halt On
: All Errors
HEAD PRECOMP
Base Memory
:
640K
Extended
Memory
:
15360K
Other Memory
:
384K
Total Memory
:
16384K
ESC : Quit
á â à ß : Select
F1 : Help
(Shift) F2 : Change Color
Item
PU / PD / + / - : Modify
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following describes
each item of this menu.
Date
The date format is:
Day :
Month :
Date :
Year :
Sun to Sat
1 to 12
1 to 31
1994 to 2079
To set the date, highlight the “Date” field and use the PageUp/ PageDown
or +/- keys to set the current time.
34
IB710 User’s Manual
BIOS SETUP
Time
The time format is:
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
Primary HDDs / Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary
channels for connecting up to four IDE hard disks or other IDE devices.
Each channel can support up to two hard disks; the first is the “Master”
and the second is the “Slave”.
To enter the specifications for a hard disk drive, you must select first a
“Type”. There are 45 predefined types and 4 user definable types are for
Enhanced IDE BIOS. Type 1 to 45 are predefined. Type “User” is
user-definable. For the Primary Master/Slave as well as Secondary
Master/Slave, you can select “Auto” under the TYPE and MODE fields.
This will enable auto detection of your IDE drives and CD-ROM drive
during POST.
Press <PgUp>/<PgDn> to select a numbered hard disk type or type the
number and press the <Enter> key. The hard disk will not work properly if
you enter incorrect information for this field. If your hard disk drive type
is not matched or listed, you can use Type User to define your own drive
type manually. If you select Type User, related information is asked to be
entered to the following items.
CYLS :
Number of cylinders
HEAD :
Number of read/write heads
PRECOMP : Write precompensation
LANDZ :
Landing zone
SECTOR :
Number of sectors
SIZE :
Automatically adjust according to the configuration
MODE (for IDE HDD only) : Auto
Normal (HD < 528MB)
Large (for MS-DOS only)
LBA (HD > 528MB and supports
Logical Block Addressing)
IB710 User’s Manual
35
BIOS SETUP
NOTE: The specifications of your drive must match with the drive
table. If your hard disk drive type is not matched or listed, you
can use Type User to define your own drive type manually.
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters.(default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA, includes high
resolution monochrome adapters.
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The system boot will not be halted for any
error that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will be halted and you will be
prompted.
All, But Keyboard The system boot will not be halted for a
keyboard error; it will stop for all other errors.
All, But Diskette
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Disk/Key The system boot will not be halted for a
keyboard or disk error; it will stop for all other
errors.
36
IB710 User’s Manual
BIOS SETUP
BIOS Features Setup
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
ROM / PCI ISA BIOS
BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Virus Warning
CPU Internal Cache
External Cache
CPU L2 Cache ECC Checking
Processor Number Feature
Quick Power On Self Test
Boot Sequence
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up Numlock Status
Gate A20 Option
Typematic Rate Setting
: Disabled
: Enabled
: Enabled
: Enabled
: Enabled
: Enabled
: A, C, SCSI
: Disabled
: Enabled
: On
: Fast
: Disabled
Video BIOS Shadow
C8000-CBFFF Shadow
CC000-CFFFF Shadow
D0000-D3FFF Shadow
D4000-D7FFF Shadow
D8000-DBFFF Shadow
DC000-DFFF Shadow
:
:
:
:
:
:
:
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Typematic Rate (chars/Sec)
:6
Typematic Delay (Msec)
: 250
Security Option
PCI /VGA Palette Snoop
OS Select For
DRAM>64MB
Report No FDD For WIN 95
: Setup
: Disabled
: Non-OS2
á â à ß : Select
Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
: Yes
F7 : Load Setup Defaults
ESC : Quit
Virus Warning
This item protects the boot sector and partition table of your hard disk
against accidental modifications. If an attempt is made, the BIOS will halt
the system and display a warning message. If this occurs, you can either
allow the operation to continue or run an anti-virus program to locate and
remove the problem. Note that some diagnostic programs would attempt
to access the boot sector table and can cause the virus warning. Disable
the Virus Warning feature when this happens.
CPU Internal Cache / External Cache
These items allow you to enable (speed up memory access) or disable the
cache function. By default, these items are Enabled.
CPU L2 Cache ECC Checking
Setting this option to Enabled to enable the ECC (error correction code)
checking on the CPU L2 cache.
Processor Number Feature
When this field is enabled, the system would detect and display the
processor ID during system boot up.
IB710 User’s Manual
37
BIOS SETUP
Quick Power On Self Test
This choice speeds up the Power On Self Test (POST) after you power up
the system. If it is set to Enabled, BIOS will skip some items.
Boot Sequence
This field determines the drive that
operating system. The options are:
A, C, SCSI (default) D, A, SCSI
C, A, SCSI
E, A, SCSI
C, CDROM, A
F, A, SCSI
the system searches first for an
SCSI, C, A
C only
LS120, C
CDROM, C, A
SCSI, A, C
Swap Floppy Drive
This item allows you to determine whether or not to enable the swap
Floppy Drive. When enabled, the BIOS swaps floppy drive assignments
so that Drive A becomes Drive B, and Drive B becomes Drive A. By
default, this field is set to Disabled.
Boot Up Floppy Seek
When enabled, the BIOS will seek whether or not the floppy drive
installed has 40 or 80 tracks. 360K type has 40 tracks while 760K, 1.2M
and 1.44M all have 80 tracks.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up the
system. By default, the system boots up with NumLock On.
Gate A20 Option
This field allows you to select how Gate A20 is worked. The Gate A20 is
a device used to address memory above 1 MB. By default, this field is set
to Fast.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. You can select speed range from 6 to 30 characters per
second. By default, this item is set to 6.
38
IB710 User’s Manual
BIOS SETUP
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
PCI/VGA Palette Snoop
Some display cards that are non-standard VGA may not show colors
properly. This field allows you to set whether or not MPEG ISA/VESA
VGA Cards can work with PCI/VGA. When this field is enabled, a
PCI/VGA can work with an MPEG ISA/VESA VGA card. When this
field is disabled, a PCI/VGA cannot work with an MPEG ISA/VESA
card.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is NON-OS/2.
Report No FDD for WIN 95
This option allows Windows 95 to share with other peripherals IRQ6 that
is assigned to a floppy disk drive if the drive is not existing. The default
setting is No.
Video BIOS Shadow
This item allows you to change the Video BIOS location from ROM to
RAM. Video Shadow will increase the video speed.
C8000 - CBFFF Shadow/DC000 - DFFFF Shadow
Shadowing a ROM reduces the memory available between 640KB to
1024KB. These fields determine whether or not optional ROM will be
copied to RAM.
IB710 User’s Manual
39
BIOS SETUP
Chipset Features Setup
This menu controls the configuration of the embedded board chipset.
ROM PCI/ISA BIOS
CHIPSET FEATURES SETUP
AWARD SOFTWARE INC.
Auto Configuration
SDRAM RAS-to-CAS Delay
SDRAM RAS Precharge Time
SDRAM CAS Latency Timer
SDRAM Precharge Control
DRAM Data Integrity Mode
System BIOS Cacheable
Video BIOS Cacheable
Video RAM Cacheable
8 Bit I/O Recovery Time
: Enabled
:3
:3
:3
: Disabled
: Non-ECC
: Enabled
: Enabled
: Enabled
:3
16 Bit I/O Recovery Time
Memory Hole At 15MB-16MB
Passive Release
Delayed Transaction
AGP Aperture Size (MB)
:2
: Disabled
: Enabled
: Disabled
: 64
Auto Detect DIMM/PCI Clk
Spread Spectrum
CPU Host Clock (CPU/PCI)
CPU Warning Temperature
Current System Temp.
Current CPU/Chip Temperature
Current CPU/Block Temp.
CPU Fan Speed
Chassis Fan Speed
VCCP
1.98 V
VTT (V)
(V):
VCC3 (V) : 3.45 V
+5V
+12 V
: 12.46 V
:
: Disabled
: Disabled
: Default
: 66°C/151°F
: 40°C/104°F
: 41°C/105°F
: 41°C/105°F
: 4440 RPM
:
0 RPM
:
1.50 V
:
4.99 V
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Auto Configuration
This field predefines values for DRAM, cache timing according to CPU
type and system clock. When this field is enabled, the predefined items
will become read-only.
SDRAM RAS-to-CAS Delay
When DRAM is refreshed, both rows and columns are addressed
separately. This field allows you to determine the timing of transition
from Row Address Stove (RAS) to Column Address Strobe (CAS).
SDRAM RAS Precharge Time
The precharge time is the number of cycles it takes for the RAS to
accumulate its charge before DRAM refresh. If insufficient time is
allowed, refresh may be incomplete and the DRAM may fail to retain
data.
SDRAM CAS Latency Time
When synchronous DRAM is installed, the number of clock cycles of
CAS latency depends on the DRAM timing. Do not reset this field from
the default value specified by the system designer.
SDRAM Precharge Control
This field enables of enables the SDRAM Precharge Control.
40
IB710 User’s Manual
BIOS SETUP
DRAM Data Integrity Mode
Set this field to ECC if the DRAM installed in the system supports it.
Otherwise, do not reset the default of Non-ECC.
System BIOS Cacheable
When enabled, access to the system BIOS ROM addressed at
F0000H-FFFFFH is cached, provided that the cache controller is
disabled.
Video BIOS Cacheable
When enabled, access to video BIOS addressed at C0000H to C7FFFH is
cached, provided that the cache controller is disabled.
Video RAM Cacheable
Selecting Enabled allows caching of the video BIOS ROM at C0000h to
C7FFFh, resulting in better video performance. However, if any program
writes to this memory area, a memory access error may result.
8 Bit I/O Recovery Time
This option specifies the length of the delay (in sysclks) inserted between
consecutive 8-bit I/O operations. The settings are 1, 2, 3, 4, 5, 6, 7, or 8.
The default setting is 3.
16 Bit I/O Recovery Time
This option specifies the length of the delay (in sysclks) inserted between
consecutive 16-bit I/O operations. The settings are 1, 2, 3, 4, 5, 6, 7, or 8.
The default setting is 2.
Memory Hole at 15MB - 16MB
In order to improve performance, certain space in memory can be reserved
for ISA cards. This field allows you to reserve 15MB to 16MB memory
address space to ISA expansion cards. This makes memory from 15MB
and up unavailable to the system. Expansion cards can only access
memory up to 16MB. By default, this field is set to Disabled.
Passive Release
When enabled, CPU to PCI bus accesses are allowed during passive
release. Otherwise, the arbiter only accepts another PCI master access to
local DRAM.
IB710 User’s Manual
41
BIOS SETUP
Delayed Transaction
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1. The default setting is Enabled.
AGP Aperture Size
The field sets aperture size of the graphics. The aperture is a portion of the
PCI memory address range dedicated for graphics memory address space.
Host cycles that hit the aperture range are forwarded to the AGP without
any translation. The default setting is 64M.
Auto Detect DIMM/PCI Clk
When enabled, the system automatically shuts off clocks of unused
DIMM/PCI slots. The default setting is Disabled.
Spread Spectrum
This value of the spread spectrum, when not disabled, can be set to 0.25%
and 0.5%. This field is for CE testing use only.
CPU Host Clock (CPU/PCI)
This field sets the value of the CPU Host Clock (CPU/PCI). The default
setting of Default automatically detects the host clock (front side bus) of
the processor. Other options include 100/33, 103/34, 112/37, 124/41,
133/44, 124/31, 133/33, 140/35, 150/37, 66/33, 75/37, and 83/41.
Note that overclocking can cause your system to become unstable.
CPU Warning Temperature
This field sets the threshold temperature at which an alert is sounded
through the system’s speaker when the value has been reached.
Current System/CPU/Chips/CPU Block Temperature
These read-only fields reflect the functions of the hardware thermal
sensor that monitors the system/CPU/chips/CPU block temperatures.
CPU Fan Speed/Chassis Fan Speed
These read-only fields show the current speeds in RPM for the
CPU/chassis fan as monitored by the hardware monitoring IC.
VCCP / VTT / VCC3 / +12V / +5/V
These read-only fields show the current voltages in the voltage regulators
and power supply as monitored by the hardware monitoring IC.
42
IB710 User’s Manual
BIOS SETUP
Power Management Setup
The Power Management Setup allows you to save energy of your system
effectively. It will shut down the hard disk and turn off video display after
a period of inactivity.
ROM PCI/ISA BIOS
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
Power Management
PM Control by APM
Video Off Method
Video Off After
Modem Use IRQ
Doze Mode
Standby Mode
Suspend Mode
HDD Power Down
Throttle Duty Cycle
PCI/VGA Active Monitor
Power On by Ring
Resume by Ring
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
: User Define
: Yes
: V/H Sync+Blank
: Standby
:3
: Disabled
: Disabled
: Disabled
: Disabled
: 62.5%
: Disabled
: Disabled
: Disabled
:0
: 7:0:0
IRQ 8 Break Suspend
: Disabled
** Reload Global Timer Events **
IRQ3 (3-7, 9-15), NMI
: Disabled
Primary IDE 0
: Disabled
Primary IDE 1
: Disabled
Secondary IDE 0
: Disabled
Secondary IDE 1
: Disabled
Floppy Disk
: Disabled
Serial Port
: Enabled
Parallel Port
: Disabled
á â à ß : Select
Item
: Help
PU/PD/+/- : Modify
: Old Values
(Shift) F2 : Color
: Load BIOS Defaults
: Load Setup Defaults
ESC : Quit
F1
F5
F6
F7
Power Management
This field allows you to select the type of power saving management
modes. The options are as follows:
Min. Power Saving
Minimum power management
Max. Power Saving
Maximum power management.
User Define
Each of the ranges is from 1 min. to 1hr.
Except for HDD Power Down which
ranges from 1 min. to 15 min.
(Default)
NOTE: In order to enable the CPU overheat protection feature, the
Power Management field should not be set to Disabled.
PM Control by APM
This field allows you to use the Advanced Power Management device to
enhance the Max. Power Saving mode and stop the CPU’s internal clock.
If the Max. Power Saving is not enabled, this will be preset to NO.
IB710 User’s Manual
43
BIOS SETUP
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank (default): blank the screen and turn off vertical and
horizontal scanning.
DPMS: allows the BIOS to control the video display card if it supports
the DPMS feature.
Blank Screen: This option only writes blanks to the video buffer.
Video Off After
As the system moves from lesser to greater power-saving modes, select
the mode in which you want the monitor to blank.
Modem Use IRQ
The IRQ used by the modem can be set to NA, 3 (default), 4, 5, 7, 9, 10
and 11.
Doze Mode
When enabled, and after the set time of system inactivity, the CPU clock
will run at a slower speed while all other devices still operate at full
speed.
Standby Mode
After the selected period of system inactivity, the fixed disk drive and the
video shut off while all other devices still operate at full speed.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Throttle Duty Cycle
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
PCI/VGA Act-Monitor
When enabled, any video activity restarts the global timer for Standby
mode. The default setting is Disabled.
PowerOn by Ring
44
IB710 User’s Manual
BIOS SETUP
When enabled, the system can be powered on through the external modem
connected.
IRQ 8 Break Suspend
You can enable or disable the monitoring of IRQ 8 (Real Time Clock) so
it does not awaken the system from Suspend mode.
Resume by Alarm
With the use of ATX power, the system can be powered on through this
field by setting the specific time for it to do so.
Reload Global Timer Events
This section determines the reloading of the ‘timers’ after entering the
Full On You can enable or disable the monitoring of IRQ 8 (Real Time
Clock) so it does not awaken the system from Suspend mode.
PM Events
The VGA, LPT & COM, HDD & FDD, DMA /master, PWR-On by
Modem/LAN, RTC Alarm Resume and Primary INTR section are I/O
events which can prevent the system from entering a power saving mode
or can awaken the system from such a mode. When an I/O device wants to
gain the attention of the operating system, it signals this by causing an
IRQ to occur. When the operating system is ready to respond to the
request, it interrupts itself and performs the service. The default value is
Off. When set On, activity will neither prevent the system from going into
a power management mode nor awaken it. The IRQ section sets the
wake-up call of the system. If activity is detected from any enabled IRQ
channels in the left-hand group, the system wakes up from suspended
mode.
IB710 User’s Manual
45
BIOS SETUP
PNP/PCI Configuration
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
ROM PCI/ISA BIOS
PNP/PCI CONFIGURATION
AWARD SOFTWARE INC.
PNP OS Installed
: No
Used MEM base addr
: N/A
Resources Controlled by
: Manual
Use MEM Length
: 8K
Reset Configuration Data
: Disabled
IRQ-3
assigned to
: Legacy ISA
IRQ-4
assigned to
: Legacy ISA
IRQ-5
assigned to
: Legacy ISA
IRQ-7
assigned to
: Legacy ISA
IRQ-9
assigned to
: Legacy ISA
IRQ-10 assigned to
: Legacy ISA
IRQ-11 assigned to
: PCI/ISA PnP
IRQ-12 assigned to
: PCI/ISA PnP
IRQ-14 assigned to
: PCI/ISA PnP
IRQ-15 assigned to
: PCI/ISA PnP
DMA-0 assigned to
: PCI/ISA PnP
DMA-1 assigned to
: Legacy ISA
ESC : Quit
á â ß : Select Item
DMA-3 assigned to
: PCI/ISA PnP
F1 : Help
PU/PD/+/- : Modify
DMA-5 assigned to
: PCI/ISA PnP
F5 : Old Values
(Shift) F2 : Color
DMA-6 assigned to
: PCI/ISA PnP
F6 : Load BIOS Defaults
DMA-7 assigned to
: PCI/ISA PnP
F7 : Load Setup Defaults
PNP OS Installed
Select Yes if the system operating environment is Plug-and-Play aware
(e.g., Windows 95). The options: Yes and No.
Resources Controlled by
The Award Plug and Play BIOS can automatically configure all the boot
and Plug and Play-compatible devices. If you select Auto, all the interrupt
request (IRQ) and DMA assignment fields disappear, as the BIOS
automatically assigns them. The options: Auto and Manual.
Reset Configuration Data
Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system reconfiguration has caused such a
serious conflict that the operating system cannot boot. The options:
Enabled and Disabled.
46
IB710 User’s Manual
BIOS SETUP
IRQ3/4/5/7/9/10/11/12/14/15, DMA0/1/3/5/6/7 assigned to
These fields allow you to determine the IRQ/DMA assigned to the ISA
bus and is not available to any PCI slot.
Used MEM base addr
Select a base address for the memory area used by any peripheral that
requires high memory. The options: C800, CC00, D000, D400, D800,
DC00, N/A.
Used MEM Length
Select a length for the memory area specified in the previous field. This
field does not appear if no base address is specified. The options: 8K,
16K, 32K, 64K.
IB710 User’s Manual
47
BIOS SETUP
Load BIOS Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
Load BIOS Defaults
SAVE
(Y/N)?
& EXIT
N SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
F6 : Save CMOS to BIOS
á â à ß : Select Item
(Shift) F2 : Change Color
F7 : Load CMOS From BIOS
Load BIOS Defaults except Standard CMOS Setup
To load BIOS defaults value to CMOS SRAM, enter “Y”. If not, enter
“N”.
Load Setup Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE & EXIT SETUP
Load Setup Defaults (Y/N)? N
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
F6 : Save CMOS to BIOS
á â à ß : Select Item
(Shift) F2 : Change Color
F7 : Load CMOS From BIOS
Load BIOS Defaults except Standard CMOS Setup
48
IB710 User’s Manual
BIOS SETUP
To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter
“N”.
IB710 User’s Manual
49
BIOS SETUP
Integrated Peripherals
This option allows you to determine your hard disk configuration, mode
and port.
ROM PCI/ISA BIOS
INTEGRATED PERIPHERALS
AWARD SOFTWARE INC.
IDE HDD Block Mode
: Enabled
Onboard FDC Controller
: Enabled
IDE Primary Master PIO
: Auto
Onboard Serial Port 1
: 3F8 / IRQ4
IDE Primary Slave PIO
: Auto
Onboard Serial Port 2
: 2F8 / IRQ3
IDE Secondary Master PIO
: Auto
UART Mode Select
: Normal
IDE Secondary Slave PIO
: Auto
IDE Primary Master UDMA
: Auto
IDE Primary Slave UDMA
: Auto
Onboard Parallel Port
: 378H/IRQ7
Parallel Port Mode
: SPP
: 3E8H
IDE Secondary Master UDMA : Auto
IDE Secondary Slave UDMA
: Auto
On-Chip Primary PCI IDE
: Enabled
On-Chip Secondary PCI IDE
: Enabled
Onboard Serial Port 3
USB Keyboard Support
: Disabled
Serial Port 3 Use IRQ
: IRQ9
Init Display First
: PCI Slot
Onboard Serial Port 4
: 2E8H
Serial Port 4 Use IRQ
: IRQ10
ESC : Quit
á â ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
IDE Primary Master/Slave PIO And Secondary Master/Slave
PIO
The four IDE PIO (Programmed Input/Output) fields let you set a PIO
mode (0-4) for each of the four IDE devices that the onboard IDE
interface supports. Modes 0 through 4 provide successively increased
performance. In Auto mode, the system automatically determines the best
mode for each device.
IDE Primary Master/Slave UDMA And Secondary
Master/Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver
(Windows 95 OSR2 or a third-party IDE bus master driver). If your hard
drive and your system software both support Ultra DMA/33, select Auto
to enable BIOS support.
50
IB710 User’s Manual
BIOS SETUP
On-Chip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
Init Display First
This field determines display to be initialized during startup. The default
setting is PCI Slot.
Onboard FDD Controller
This should be enabled if your system has a floppy disk drive (FDD)
installed on the system board and you wish to use it. Even when so
equipped, if you add a higher performance controller, you will need to
disable this feature.
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial/parallel port and its
address. The default values for these ports are:
Serial Port 1
3F8/IRQ4
Serial Port 2
2F8/IRQ3
Serial Port 3
3F8/IRQ9
Serial Port 4
2E8H/IRQ10
Parallel Port
378H/IRQ7
UART Mode Select
This item allows you to determine which Infra Red (IR) function of
onboard I/O chip. The options are Normal, IrDA, and ASKIR.
Onboard Parallel Mode
This field allows you to determine parallel port mode function.
SPP
Standard Printer Port
EPP
Enhanced Parallel Port
ECP
Extended Capabilities Port
ECP+EPP Extended Capabilities Port or Enhanced Parallel Port
IB710 User’s Manual
51
BIOS SETUP
Supervisor / User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password, the
screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are prompted
to enter the password. A message will confirm the password to be
disabled. Once the password is disabled, the system will boot and you can
enter Setup freely.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE & EXIT SETUP
Enter Password:
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
F6 : Save CMOS to BIOS
á â à ß : Select Item
(Shift) F2 : Change Color
F7 : Load CMOS From BIOS
Change / Set / Disable Password
52
IB710 User’s Manual
BIOS SETUP
IDE HDD Auto Detection
This option detects the parameters of an IDE hard disk drive, and
automatically enters them into Standard CMOS Setup screen.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
HARD DISKS
TYPE
SIZE
CYLS HEAD PRECOMP
LANDZ
SECTOR
MODE
Primary Master:
Select Primary Master Option (N=SKIP) : N
OPTIONS
TYPE
SIZE
1 (Y)
0
0
CYLS HEAD PRECOMP
0
0
0
LANDZ
SECTOR
MODE
0
0
NORMAL
NOTE: Some OSes (like SCO-UNIX) must use ”N ORMAL” for installation
ESC: SKIP
Up to four IDE drives can be detected, with parameters for each appearing
in sequence inside a box. To accept the displayed entries, press the “Y”
key to skip to the next drive, press the “N” key. If you accept the values,
the parameters will appear listed beside the drive letter on the screen.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to Setup
utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
IB710 User’s Manual
53
VGA DRIVERS INSTALLATION
VGA Drivers Installation
This section provides information on how to install the C&T 69000 VGA
drivers that come with your IB710 board. Please follow the instructions
set forth in this section carefully. If the VGA drivers come in floppy
diskettes, it is recommended that you make a backup copy of the VGA
drivers and put the backup copy in a safe place.
For your information, Windows 2000 can detect the C&T 69000 VGA
hardware and install the drivers automatically from the Windows 2000
CD.
The following items are covered in this section:
Installing the Drivers for Windows 95/98....................................... 55
Installing the Drivers for Windows NT 4.0..................................... 56
54
IB710 User’s Manual
VGA DRIVERS INSTALLATION
Installing the Drivers for Windows 95/98
The following section describes the normal display driver installation
procedures for Windows 95/98. Use the following procedures when
installing the display drivers for Windows 95/98.
1. Click Start, then Settings, then Control Panel.
2. Double click Display.
3. Select the Settings tab, click the Change Display Type button.
4. Click the Change button under Adapter Type.
5. Click the Have Disk button and press OK.
6. Specify the path to the new driver and press <ENTER>:
Example 1: Insert the driver CD in the CD-ROM drive, and enter
d:\vga\ct69000\win95 (assuming D: is the CD-ROM drive.)
Example 2: If you're not sure exactly where the drivers are, click the
Browse button to find them.
7. The Select Device dialog box will appear. Select the hardware that
corresponds to the one you installed in your machine and click OK.
8. Windows 95/98 will copy the display drivers to the proper
directories on your system.
9. Continue by choosing Close. You will be asked to restart your
machine. Do so accordingly.
10. After the system has restarted, you can go back into the Display
applet and select alternate screen resolutions and color depths.
IB710 User’s Manual
55
VGA DRIVERS INSTALLATION
Installing the Drivers for Windows NT 4.0
Once you are in the Windows NT 4.0 environment, follow the procedures
below to install the VGA drivers that come with your embedded board.
1. Click the Start button, then go to Settings and click on Control
Panel.
2. Click on the Display icon to start the Display Properties window.
3. Click on the Settings tab, and then click on Display Type.
4. In the Change Display Type window, click on Change Adapter
Type. This will bring up the Select Device window.
5. In the Change Display window, click on Have Disk. Enter the
directory where the Windows NT driver files are located as
d:\vga\ct69000\winnt40 (assuming D: is the CD-ROM drive.)
Then select OK, or press ENTER.
6. Select Chips Video Accelerator from the display list provided, then
click OK or press ENTER.
7. You will then see a warning panel about Third Party Drivers. Click
on Yes to finish the installation.
8. Once the installation is complete, the system must be shut down and
restarted for the new drivers to take effect.
9. When the system has restarted, the default graphics mode (usually
640x480x256color) has been automatically selected. Click the Start
button, and then go to Settings and click on Control Panel. Click on
the Display icon to start the Display Properties window. Click on
the Settings tab. A new screen setting can be selected using either of
the following methods:
A. Use the slide-bar in the Desktop Area to select new setting.
B. Click on List All Modes. From the list provided, select a
new setting, then click OK or press ENTER.
C. Click on Test to test the newly selected graphics mode.
Follow the instructions given on screen. A test screen
should appear, followed by the Testing Mode window.
Click on Yes to continue. Click on Apply to switch to the
new graphics mode. Graphics modes are changed
dynamically on NT 4.0, so you do not need to shut down and
restart for the new screen settings to work.
56
IB710 User’s Manual
VGA DRIVERS INSTALLATION
This page was intentionally left blank.
IB710 User’s Manual
57
AUDIO DRIVERS INSTALLATION
Audio Drivers Installation
This section provides information on how to install the audio drivers for
ESS Solo-1 ES1938S that come in floppy diskettes with your IB710
board. Please follow the instructions set forth in this section. It is
recommended that you make a copy of the drivers and put the backup
copy in a safe place.
The following items are covered in this section:
Installing the Audio Driver for Windows 95 .................................. 59
Installing the Audio Driver for Windows 98 .................................. 60
Installing the Audio Driver for Windows NT ................................. 61
58
IB710 User’s Manual
AUDIO DRIVERS INSTALLATION
Installing the Audio Driver for Windows 95
1.
2.
3.
4.
Turn on the computer and start Windows 95.
Insert the CD containing the ESS Solo-1 ES1938S audio drivers for
Windows 95.
The CD autoruns and shows a screen with options for you to choose.
Click on Sound and select ESS Solo-1 to install the audio software
and drivers. The welcome screen is then displayed.
Click the Next button to continue the installation process. When the
ESS Solo-1 Installation window appears, select Upgrade Drivers
and click the Next button.
5. After file copying is done, restart Windows 95.
6. When Windows restart, it will detect a PCI Multimedia Audio
Device. Insert the audio driver CD and click the Next button to start
file copying, then click Finish.
7. When prompted to insert the Windows 95 CD, do accordingly and
click OK. Key in the path (for example, d:\win95) where the
Windows 95 files are located and click OK. The installation is
complete.
IB710 User’s Manual
59
AUDIO DRIVERS INSTALLATION
Installing the Audio Driver for Windows 98
1.
2.
3.
4.
Turn on the computer and start Windows 98.
Insert the diskette containing the ESS Solo-1 ES1938S audio drivers
for Windows 98.
The CD autoruns and shows a screen with options for you to choose.
Click on Sound and select ESS Solo-1 to install the audio software
and drivers. The welcome screen is then displayed.
Click the Next button to continue the installation process. When the
ESS Solo-1 Installation window appears, select Upgrade Drivers
and click the Next button.
5. After file copying is done, restart Windows 98.
6. When Windows restarts, it will detect a PCI Multimedia Audio
Device. Insert the audio driver CD and click the Next button. Click on
the Search for the best driver checkbox, then click Next. Now
install The Update driver, ESSSolo-1 PCI Audio Device. Click Next
and then Next again to start file copying. After file copying is done,
click Finish
7. Now, Windows detects a new hardware which is the gameport
joystick. Click OK and insert the Windows 98 CD and key in the path
(for example, d:\win98) where the Windows 98 files are located and
click OK. The installation is complete.
60
IB710 User’s Manual
AUDIO DRIVERS INSTALLATION
Installing the Audio Driver for Windows NT
1.
2.
3.
4.
Turn on the computer and start Windows NT.
Insert the diskette or CD containing the ESS Solo-1 ES1938S audio
drivers for Windows NT.
The CD autoruns and shows a screen with options for you to choose.
Click on Sound and select ESS Solo-1 to install the audio software
and drivers. The welcome screen is then displayed.
Click the Next button to continue the installation process. When the
ESS Solo-1 Installation window appears, select Upgrade Drivers
and click the Next button.
5. When the Choose Driver Language window appears, choose
English and click the Next button to start file copying. After file
copying is done, click Finish to restart Windows NT and for changes
to take effect.
IB710 User’s Manual
61
LAN DRIVERS INSTALLATION
LAN Drivers Installation
This section describes LAN features and driver installation of the onboard
Realtek RTL8139 Ethernet controller.
The following items are covered in this section:
Introduction....................................................................................... 63
Features............................................................................................. 63
Installing LAN Drivers for Windows 98/Windows 2000 .............. 64
Installing LAN Drivers for Windows 95......................................... 64
Installing LAN Drivers for Windows NT........................................ 65
62
IB710 User’s Manual
LAN DRIVERS INSTALLATION
Introduction
Realtek RTL8139 is a 32-bit 10/100MBps Ethernet controller for PCI
local bus-compliant PCs. It supports bus mastering architecture, and
auto-negotiation feature which make it possible to combine one common
type of Ethernet cabling – an RJ-45 connector for twisted-pair cabling
that can be used for both 10Mbps and 100Mbps connection. Extensive
driver support for commonly used network operating systems is also
provided.
Features
l
l
l
l
l
l
Conforms to the Ethernet IEEE 802.3u standard
Compatible with PCI Local Bus Revision 2.1 specification
IEEE 802.3u Auto-Negotiation for automatic speed selection
Supports Full-Duplex/Half-Duplex Operation
Provides 32-bit bus mastering data transfer
Supports 10Mbps and 100Mbps operation in a single port
The following section describes the installation driver procedure for
Windows 98/Windows 2000, Windows 95, Windows NT, DOS, and
Windows for Workgroup. To view the procedure of other operating
systems, execute the help8139.exe in the diskette or CD supplied.
IB710 User’s Manual
63
LAN DRIVERS INSTALLATION
Installing LAN Drivers for Windows 98/Windows 2000
This section describes the procedure to install Windows 98 and Windows
2000 drivers for Realtek RTL8139 PCI Fast Ethernet controller.
1.
2.
3.
4.
5.
Executing Windows 98/Windows2000 will auto-detect your system
configuration and find the Ethernet hardware.
When asked to select the driver to install, select Driver from disk
provided by hardware manufacturer.
Insert the CD containing the Realtek RTL8139 drivers into the
CD-ROM drive and specify the setup file pathname as
d:\lan\realtek\win98 or d:\lan\realtek\win2000 (assuming D: is
your CD-ROM drive.)
After the driver files are copied, Windows 98/Windows2000 will
appear with a message to insert Windows 98/Windows 2000 system
disk to complete setup. Do so accordingly.
Windows 98/Windows2000 will finish other installation procedure
automatically and ask you to restart the system.
Installing LAN Drivers for Windows 95
This section describes the procedure to install Windows 95 driver for
Realtek RTL8139 PCI Fast Ethernet hardware.
1.
2.
3.
4.
5.
64
Executing Windows 95 will auto-detect your system configuration
and find the Ethernet hardware.
When asked to select the driver you want to install, select Driver
from disk provided by hardware manufacturer.
Insert the CD containing the Realtek RTL8139 drivers into the
CD-ROM drive and specify the setup file pathname as
d:\lan\realtek\win95 (assuming D: is your CD-ROM drive.)
Windows 95 will appear with a message to insert Windows 95
system disk to complete setup. Do so accordingly.
Windows 95 will finish other installation procedure automatically,
and ask you to restart the system.
IB710 User’s Manual
LAN DRIVERS INSTALLATION
Installing LAN Drivers for Windows NT
This section describes the procedure to install Windows NT v3.5, v3.51
& v4.0 driver for Realtek RTL8139 PCI Fast Ethernet hardware.
When you are in Windows NT :
1. In the Main group of Windows NT, select the Control Panel icon.
2. In the Control Panel window, choose the Network icon.
3. In the Network Settings dialog box, choose the Add Adapter button.
The Add Network Adapter dialog box appears.
4. In the list of network cards, select <other> Requires disk from
manufacturer, and then press Enter button.
5. Insert the CD containing the Realtek drivers, enter drive and pathname
as d:\lan\realtek\winnt40 (assuming d: is the CD-ROM drive) where
the setup file OEMSETUP.INF is located, and then choose the OK
button.
6. The screen will appear Select Line Speed dialog box which is provided
by RTL8139.SYS driver. The default value is auto. The RTL8139 PCI
Fast Ethernet hardware and its driver RTL8139.SYS will auto-detect
the line speed -- 10Mb or 100Mb, while the RTL8139.SYS is loading.
The other values, 10 or 100, are only used when you want to force
RTL8139 PCI Fast Ethernet hardware to 10Mb or 100Mb.
7. The screen will show the Input EthernetID dialog box which is
provided by RTL8139.SYS driver. This option is only required when
you have more than one Realtek RTL8139 PCI Fast Ethernet hardware
on the system. Select SKIP if only one Ethernet hardware installed on
the computer.
8. After installation is complete, restart your system for changes to take
effect.
IB710 User’s Manual
65
APPENDIX
Appendix
A. Post Codes
B. I/O Port Address Map
C. Interrupt Request Lines (IRQ)
66
IB710 User’s Manual
APPENDIX
A. POST Codes
POST (Power On Self Test) codes are to determine problems during boot
up. Below are the codes for your reference.
Description
POST (hex)
CFh
Test CMOS R/W functionality.
C0h
Early chipset initialization:
-Disable shadow RAM
-Disable L2 cache (socket 7 or below)
-Program basic chipset registers
C1h
Detect memory
-Auto-detection of DRAM size, type and ECC.
-Auto-detection of L2 cache (socket 7 or below)
C3h
Expand compressed BIOS code to DRAM
C5h
Call chipset hook to copy BIOS back to E000 & F000 shadow
RAM.
01h
Expand the Xgroup codes locating in physical address 1000:0
03h
Initial Superio_Early_Init switch.
04h
Reserved
05h
1. Blank out screen
2. Clear CMOS error flag
06h
Reserved
07h
1. Clear 8042 interface
2. Initialize 8042 self-test
08h
1. Test special keyboard controller for Winbond 977 series
Super
I/O chips.
2. Enable keyboard interface.
09h
Reserved
0Ah
1. Disable PS/2 mouse interface (optional).
2. Auto detect ports for keyboard & mouse followed by a port
& interface swap (optional).
3. Reset keyboard for Winbond 977 series Super I/O chips.
0Eh
Test F000h segment shadow to see whether it is R/W-able or not.
If test fails, keep beeping the speaker.
10h
Auto detect flash type to load appropriate flash R/W codes into
the run time area in F000 for ESCD & DMI support.
IB710 User’s Manual
67
APPENDIX
POST (hex)
Description
12h
Use walking 1’s algorithm to check out interface in CMOS
circuitry. Also set real-time clock power status, and then check
for override.
14h
Program chipset default values into chipset. Chipset default
values are MODBINable by OEM customers.
16h
Initial Early_Init_Onboard_Generator switch.
18h
Detect CPU information including brand, SMI type (Cyrix or
Intel) and CPU level (586 or 686).
1Bh
Initial interrupts vector table. If no special specified, all H/W
interrupts are directed to SPURIOUS_INT_HDLR & S/W
interrupts to SPURIOUS_soft_HDLR.
1Dh
Initial EARLY_PM_INIT switch.
1Fh
Load keyboard matrix (notebook platform)
21h
HPM initialization (notebook platform)
23h
1. Check validity of RTC value:
e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If CMOS checksum
fails, use default value instead.
3. Prepare BIOS resource map for PCI & PnP use. If ESCD is
valid, take into consideration of the ESCD’s legacy
information.
4. Onboard clock generator initialization. Disable respective
clock resource to empty PCI & DIMM slots.
5. Early PCI initialization:
-Enumerate PCI bus number
-Assign memory & I/O resource
-Search for a valid VGA device & VGA BIOS, and put it
into C000:0.
27h
Initialize INT 09 buffer
29h
1. Program CPU internal MTRR (P6 & PII) for 0-640K memory
address.
2. Initialize the APIC for Pentium class CPU.
3. Program early chipset according to CMOS setup. Example:
onboard IDE controller.
4. Measure CPU speed.
5. Invoke video BIOS.
2Dh
1. Initialize multi-language
2. Put information on screen display, including Award title, CPU
type, CPU speed … .
33h
Reset keyboard except Winbond 977 series Super I/O chips.
3Ch
Test 8254
3Eh
Test 8259 interrupt mask bits for channel 1.
40h
Test 8259 interrupt mask bits for channel 2.
43h
Test 8259 functionality.
68
IB710 User’s Manual
APPENDIX
POST (hex)
Description
47h
Initialize EISA slot
49h
1. Calculate total memory by testing the last double word of
each 64K page.
2. Program writes allocation for AMD K5 CPU.
4Eh
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with
proper cacheable range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in
case the cacheable ranges between each CPU are not
identical.
50h
Initialize USB
52h
Test all memory (clear all extended memory to 0)
55h
Display number of processors (multi-processor platform)
57h
1. Display PnP logo
2. Early ISA PnP initialization
-Assign CSN to every ISA PnP device.
59h
Initialize the combined Trend Anti-Virus code.
5Bh
(Optional Feature)
Show message for entering AWDFLASH.EXE from FDD
(optional)
5Dh
1. Initialize Init_Onboard_Super_IO switch.
2. Initialize Init_Onbaord_AUDIO switch.
60h
Okay to enter Setup utility; i.e. not until this POST stage can users
enter the CMOS setup utility.
65h
Initialize PS/2 Mouse
67h
Prepare memory size information for function call:
INT 15h ax=E820h
69h
Turn on L2 cache
6Bh
Program chipset registers according to items described in Setup &
Auto-configuration table.
6Dh
1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the
corresponding item in Setup is set to “AUTO”.
6Fh
1. Initialize floppy controller
2. Set up floppy related fields in 40:hardware.
73h
(Optional Feature)
Enter AWDFLASH.EXE if :
-AWDFLASH is found in floppy drive.
-ALT+F2 is pressed
75h
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM… ..
77h
Detect serial ports & parallel ports.
7Ah
Detect & install co-processor
IB710 User’s Manual
69
APPENDIX
POST (hex)
7Fh
82h
83h
84h
85h
93h
94h
95h
96h
FFh
70
Description
1. Switch back to text mode if full screen logo is supported.
-If errors occur, report errors & wait for keys
-If no errors occur or F1 key is pressed to continue:
wClear EPA or customization logo.
1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen
logo)
3. If password is set, ask for password.
Save all data in stack back to CMOS
Initialize ISA PnP boot devices
1. USB final Initialization
2. NET PC: Build SYSID structure
3. Switch screen back to text mode
4. Set up ACPI table at top of memory.
5. Invoke ISA adapter ROMs
6. Assign IRQs to PCI devices
7. Initialize APM
8. Clear noise of IRQs.
Read HDD boot sector information for Trend Anti-Virus code
1. Enable L2 cache
2. Program boot up speed
3. Chipset final initialization.
4. Power management final initialization
5. Clear screen & display summary table
6. Program K6 write allocation
7. Program P6 class write combining
1. Program daylight saving
2. Update keyboard LED & typematic rate
1. Build MP table
2. Build & update ESCD
3. Set CMOS century to 20h or 19h
4. Load CMOS time into DOS timer tick
5. Build MSIRQ routing table.
Boot attempt (INT 19h)
IB710 User’s Manual
APPENDIX
B. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port addresses
which also becomes the identity of the device. The following table lists
the I/O port addresses used on the Embedded Little Board.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278 - 27F
2F8h - 2FFh
2B0 - 2DF
378h - 3FFh
360 - 36F
3B0 - 3BF
3C0 - 3CF
3D0 - 3DF
3F0h - 3F7h
3F8h - 3FFh
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
IB710 User’s Manual
71
APPENDIX
C. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on the Embedded Little Board.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
72
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Parallel Port #2
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Serial Port #3
Serial Port #4
Reserved
80287
Primary IDE
Secondary IDE
IB710 User’s Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement