Omega FMA-A2100,-A2300, -A2200,-A2400 Owner Manual
Advertisement
Advertisement
OMEGAnet ® Online Service Internet e-mail omega.com [email protected]
U.S.A.:
ISO 9001 Certified
Canada:
Servicing North America:
Omega Engineering, Inc., One Omega Drive, P.O. Box 4047
Stamford, CT 06907-0047
Toll-Free: 1-800-826-6342
FAX: (203) 359-7700
Tel: (203) 359-1660 e-mail: [email protected]
976 Bergar
Laval (Quebec), Canada H7L 5A1
Toll-Free: 1-800-826-6342
FAX: (514) 856-6886
TEL: (514) 856-6928 e-mail: [email protected]
For immediate technical or application assistance:
U.S.A. and Canada: Sales Service: 1-800-826-6342/1-800-TC-OMEGA ®
Customer Service: 1-800-622-2378/1-800-622-BEST ®
Engineering Service: 1-800-872-9436/1-800-USA-WHEN ®
Mexico:
Benelux:
En Español: 001 (203) 359-7803 FAX: (001) 203-359-7807 [email protected]
e-mail: [email protected]
Servicing Europe:
Managed by the United Kingdom Office
Toll-Free: 0800 099 3344 TEL: +31 20 347 21 21
FAX: +31 20 643 46 43 e-mail: [email protected]
Czech Republic: Frystatska 184
733 01 Karviná, Czech Republic
Toll-Free: 0800-1-66342
FAX: +420-59-6311114
France:
TEL: +420-59-6311899 e-mail: [email protected]
Managed by the United Kingdom Office
Toll-Free: 0800 466 342 TEL: +33 (0) 161 37 29 00
FAX: +33 (0) 130 57 54 27 e-mail: [email protected]
Germany/Austria: Daimlerstrasse 26
D-75392 Deckenpfronn, Germany
Toll-Free: 0 800 6397678
FAX: +49 (0) 7056 9398-29
TEL: +49 (0) 7059 9398-0 e-mail: [email protected]
United Kingdom: OMEGA Engineering Ltd.
ISO 9001 Certified One Omega Drive, River Bend Technology Centre, Northbank
Irlam, Manchester M44 5BD England
Toll-Free: 0800-488-488
FAX: +44 (0)161 777-6622
TEL: +44 (0)161 777-6611 e-mail: [email protected]
It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New
Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, human applications.
TABLE OF CONTENTS
1.0 Introduction and Description..................................................2
2.0 Specifications ........................................................................3
3.0 Installation..............................................................................4
3.1
Plumbing Connections ..........................................4
3.20 Power ....................................................................4
3.21 Output ....................................................................4
3.22 Setpoint ..................................................................4
3.23 D Conn Pin Out ......................................................5
4.0 Operation ..............................................................................6
4.1
Zero Check ............................................................6
4.11 Display Zero ..........................................................6
4.12 O-5 Output Zero ....................................................6
4.2
Flow Measurement ................................................6
4.3
Flow Control ..........................................................6
5.0 Using K Factors ....................................................................7
6.0 Special Notes ........................................................................8
Index of Appendix
A.
Part List ......................................................................9
B.
Gas K Factors ..........................................................10
Omega FMA Series Instruction Manual
1
TABLE OF CONTENTS
1.0 Introduction and Description..................................................2
2.0 Specifications ........................................................................3
3.0 Installation..............................................................................4
3.1
Plumbing Connections ..........................................4
3.20 Power ....................................................................4
3.21 Output ....................................................................4
3.22 Setpoint ..................................................................4
3.23 D Conn Pin Out ......................................................5
4.0 Operation ..............................................................................6
4.1
Zero Check ............................................................6
4.11 Display Zero ..........................................................6
4.12 O-5 Output Zero ....................................................6
4.2
Flow Measurement ................................................6
4.3
Flow Control ..........................................................6
5.0 Using K Factors ....................................................................7
6.0 Special Notes ........................................................................8
Index of Appendix
A.
Part List ......................................................................9
B.
Gas K Factors ..........................................................10
Omega FMA Series Instruction Manual
1
1.0 Description
Omegaʼs FMA Series mass flow meters and controllers utilize a capillary type thermal technology to directly measure mass flow.
No temperature, pressure, or square root corrections are required.
The FMA Series is available with an LCD display and linear 0-5 or 4-20 ma output. Display and outputs read in direct Engineering units. Engineering units may be mass units such as Gr/s, LB/H,
Kg/H...or in volumetric units referenced to a standard pressure and temperature I.E. SCCM, SLPM, SCFH. Omega uses 70° F and 29.92” Hg or 21° C and 760 Torr as standard reference conditions. (Others available on request).
The FMA Series is available in Polyoxymethylene (POM) or 316
Stainless Steel. Polyoxymethylene (POM) is compatible with most non-corrosive gases. The user is responsible to check wetted materials against gas compatibility.
Omega mass flow meters are calibrated to NIST standards for a specific gas and range selected by the customer, however K
Factors can be used to measure other gases.
FMA Series controllers use an integral electromagnetic proportional valve to control the mass flow rate. Command signal is supplied by the onboard set point pot or a external 0-5 VDC supplied to the D connector.
Omega cost savings design supplies a complete flow measurement and control system in one compact package making it ideal for OEM, laboratories, and process control applications.
Omega FMA Series Instruction Manual
2 2
2.0 Specifications
Wetted Material
Flow Bodies Plastic Model
(POM), 316 SS & 17-4SS
Stainless Steel Model
316/174 SS
Elastomers
Output Signal
Input Power
Standard - FKM
Optional - Buna, Perfluoroelastomer, or
EPDM.
Linear 0-5 VDC Linear or 4-20 MA
Standard: 24 VDC @ 350 MA
Optional: 12, 15 VDC / 115, 220 VAC with
AC adapter
Connection
Control Signal
Control Valve
Max Pressure
Response Time
9 pin Sub D
Integral or 0-5 VDC
Electromagnetic
Norm. Closed
Plastic Model - 250 PSIG, Stainless Steel
Model - 500 PSIG
1-2 second
Omega FMA Series Instruction Manual
3
3.0 Installation
3.1 Plumbing
(Caution: The FMA Series has a maximum temperature or 150 F and a maximum pressure of 500 psig.)
The FMA Series has 2 x 4-40 mounting holes on the bottom.
Standard fittings are 1/4” compression fitting. When plumbing meters insure the flow arrow on the front label is in the direction of flow. Before operation insure system is leak free.
Capillary mass meters are susceptible to clogging. If your line or gas has particulate entrained use a 50 - 100 micron filter up stream of the meter.
3.20 Power
Omega FMA series meters require 24 VDC @ 250 ma for meters and 320ma for controllers, via the 9 pin sub D connector.
Power is typically supplied with a wall mounted AC adapter.
3.21 Output
Omega FMA series has a standard 0 - 5 VDC and 4-20 ma linear output from the 9 pin sub D connector. The 4 - 20 MA signal is a self powered “4 wire type” referenced from ground, do not apply power to this line.
3.22 Setpoint
The FMA series controllers require a linear 0 - 5 VDC setpoint.
This signal can be supplied from the integral setpoint pot located on the right side of the controller or from a remote source. The integral setpoint is jumpered through the mating sub D connector from pins 9 to 5. To use a remote setpoint signal, open the mating sub D connector housing and remove the jumper between pins 5 & 9 and input the remote 0-5 VDC on pins #5(+),
#2(common) and wire remote 0 - 5 to pins 5 (Hi) & 2 (Common).
4
3.24 D Conn. Pin Out
Pin Number
1
2
3
4
Function
Power Supply Ground
Set Point input Lo
4-20 MA Output High (blue wire)
0-5 VDC Output High (orange wire)
5 Set Point Input High
6 NC
7
8
9
24 VDC Power Input
Output Ground (brown wire)
Local Set Point Supply
(Must be jumpered to pin 5 for local set point.)
5 5
4.0 Operation
Apply power through the sub D connector and allow 5-10 minutes warm up time. Controllers should have a zero setpoint. For local setpoint models turn the setpoint adjustment knob fully clockwise.
4.1 Zero Check
Zero may shift in shipping or installation. Zero should be adjusted after installation to insure accuracy.
Insure there is no flow through the transducer and check the 0 - 5 output or display for a zero reading.
4.11 Set Zero
The zero adjustment screw is available on the right hand side of the meter. Turn the screw slowly until the display or 0 - 5 VDC output is at zero.
4.2 Flow Measurement
The FMA Series transducers measure mass flow directly and read out in mass units per time. When calibrated for volumetric units measurements are referenced from a standard temperature and pressure. Outputs are linear over the calibrated flow range
4.3 Flow Control
Flow controllers combine a mass flow transducer with a normally closed electromagnetic proportional valve. Controllers use a 0 - 5
VCD linear setpoint signal supplied from the local setpint pot or from a remote source. The local setpoint voltage must be connected through the external mating D connector from pins 9 to 5. This will enable the knob on the side of the mass flow controller. For remote setpoint remove this jumper and wire 0 - 5
VDC to pins #2(common) and #5(+). Valves have a standard minimum and maximum operating differential pressures of 10 - 50
PSIG. Others available on request.
6
5.0 Using K Factors
The FMA Series uses a thermal sensor technology which allows the use of conversion factors from the calibrated gas to other gases. To change to a new gas multiply the flow rate reading by the ratio of the K factor for the new gas to the K factor of the calibrated gas.
Reading X
K Factor New Gas
K Factor Cal. Gas
7
8 8
9
10 10
11
12
13
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer
Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification.
This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moistur e or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL
IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF
LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall
OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANTY/ DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT
(IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following information available BEFORE contacting OMEGA:
1. Purchase Order number under which the product was PURCHASED,
2. Model and serial number of the product under warranty, and
3. Repair instructions and/or specific problems relative to the product.
FOR NON-WARRANTY REPAIRS, consult
OMEGA for current repair charges. Have the following information available BEFORE contacting OMEGA:
1. Purchase Order number to cover the
COST of the repair,
2. Model and serial number of theproduct, and
3. Repair instructions and/or specific problems relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible.
This affords our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2009 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at omega.com
SM
TEMPERATURE
⻬ Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
䡺
⻬ Calibrators & Ice Point References
䡺
⻬ Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
⻬ Transducers & Strain Gages
䡺
⻬ Displacement Transducers
䡺
FLOW/LEVEL
⻬ Rotameters, Gas Mass Flowmeters & Flow Computers
䡺
⻬ Turbine/Paddlewheel Systems
䡺 pH/CONDUCTIVITY
⻬ pH Electrodes, Testers & Accessories
䡺
⻬ Controllers, Calibrators, Simulators & Pumps
䡺
DATA ACQUISITION
⻬ Data Acquisition & Engineering Software
䡺
⻬ Plug-in Cards for Apple, IBM & Compatibles
䡺
⻬ Recorders, Printers & Plotters
HEATERS
⻬ Heating Cable
䡺
⻬ Immersion & Band Heaters
䡺
⻬ Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
⻬ Metering & Control Instrumentation
䡺
䡺
䡺
⻬ Industrial Water & Wastewater Treatment
䡺
M-2842/0712

Public link updated
The public link to your chat has been updated.
Advertisement