Quick Start Guide
NETVANTA 4305 (SYSTEM)
For more detailed documentation, visit us online at www.adtran.com
P/N 1200890L1
STATUS
WAN
NET 1
DBU
TD
RD
WAN
NET 2
DBU
TD
RD
LAN 1
TD
RD
LNK
LAN 2
TD
RD
LNK
WIDE SLOT 1
STATUS
ACTIVITY
TEST
NetVanta 4305
I
NSTALL THE
N
ETWORK
I
NTERFACE
M
ODULE
(NIM)
1.
Verify the unit is not connected to a power source.
2.
(Optional) To install the Dial Backup Interface Module (DIM), carefully align the P1 connector on the NIM with the J1 connector on the DIM. Using only fingertip pressure to ensure that neither circuit board bends or flexes, firmly seat the connectors. Secure the DIM to the NIM using the supplied screws and standoff posts.
3.
Slide the NIM into the option slot until the module is firmly positioned against the back of the chassis.
4.
Secure the push pins at both edges of the module.
5.
(Optional) To install the Wide Slot Interface Module, align the module with
Slot 3 and slide the module into the chassis until it is firmly positioned against the backplane connectors. Secure by tightening the screws.
C
ONNECT TO THE
N
ET
V
ANTA
4305 C
ONSOLE
Before connecting to the NetVanta 4305 CONSOLE interface you will need the following items: VT100 terminal or PC (with VT100 terminal emulation software) and a straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal (or PC) on the other.
1.
Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the unit.
2.
Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal emulation software).
3.
Open a VT100 terminal session to the NetVanta 4305 using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the ADTRAN Command Line Interface.
4.
Enter enable at the > prompt.
5.
Enter the password when prompted. The default password is password.
Quick Start Guide, 61200890L1-13A, June 2004
LED D
ESCRIPTIONS
For these
LEDs…
STATUS
This activity…
Green
(blinking)
Green (solid)
Red (solid)
Yellow (solid)
NET 1/ NET 2
WAN
Off
Green (solid)
Red (solid)
Yellow (solid)
NET 1/ NET 2
DBU
Off
Green (solid)
Green
(blinking)
Red (solid)
NET 1/NET 2
TD/RD
Yellow (solid)
Green
(blinking)
Off
LAN 1/ LAN 2
LNK
Green (solid)
LAN 1/ LAN 2
TD/RD
Yellow (solid)
Green
(blinking)
Off
Indicates that…
Unit is powering up. On power-up the STAT LED blinks rapidly for five seconds, during which time the user may escape to boot mode from the console port.
Power is on and self-test passed.
Power is on, but the self-test failed or the boot mode (if applicable) code could not be booted.
Unit is in test.
No NIM is installed, or interface is administratively down.
Link is up and everything is operational.
An alarm condition is occurring on the WAN interface, or there is a self-test failure.
Unit is in test.
No DIM is installed.
DIM is ready. For the ISDN BRI DIM, green solid indicates that the negotiation with the switch is complete.
Unit is in dial backup.
An alarm condition is occurring on the DBU interface, or there is a self-test failure.
Unit is in test.
There is activity on the WAN or DBU port.
There is no activity on the WAN or DBU port.
10BaseT Ethernet link is up.
100BaseT Ethernet link is up.
There is activity on the Ethernet port.
There is no activity on the Ethernet port.
Technical Support 1-888-4ADTRAN (1-888-423-8726)
© 2004 ADTRAN, All Rights Reserved
Quick Start Guide
NETVANTA 4305 (SYSTEM)
For more detailed documentation, visit us online at www.adtran.com
P/N 1200890L1
ETH 0/2
100-250VAC, 0.75A
50/60Hz
WAN-T1 DSX-1 DBU
CONSOLE
SLOT 3 WIDE MODULE
LED D
ESCRIPTIONS
(C
ONTINUED
)
Indicates that… For these
LEDs…
WIDE SLOT 1
STATUS
This activity…
Off
WIDE SLOT 1
ACTIVITY
Green (solid)
Red (solid)
Green
(blinking)
Off
WIDE SLOT 1
TEST
Off
Yellow (solid)
Card is not installed.
Card is recognized by the system
Alarm condition with card.
There is data activity on the card (e.g., for the Octal T1
Module, this indicates TD/RD data).
There is no data activity on card.
Card is not in test.
Card is in test mode.
C
ONSOLE
P
INOUT
7
8
9
4
5
6
2
3
Pin
1
Name
DCD
RD
TD
DTR
SG
DSR
RTS
CTS
RI
Description
Data Carrier Detect (output)
Receive Data (output)
Transmit Data (input)
Data Terminal Ready (input)
Signal Ground
Data Set Ready (output)
Request to Send (input)
Clear to Send (output)
Ring Indicate (output)
Quick Start Guide, 61200890L1-13A, June 2004
SLOT 2 NET/DBU
Technical Support 1-888-4ADTRAN (1-888-423-8726)
SLOT 1 NET/DBU ETH 0/1
E
THERNET
P
INOUT
Pin
1
2
3
4, 5
6
7, 8
Name
TX1
TX2
RX1
—
RX2
—
Description
Transmit Positive
Transmit Negative
Receive Positive
Unused
Receive Negative
Unused
C
OMMANDS
Refer to the ADTRAN Operating System (OS) Command Reference Guide
(provided on the ADTRAN OS Documentation CD) for details on configuring the system using the Command Line Interface.
© 2004 ADTRAN, All Rights Reserved