Sharp | DK-KP80PH | Specifications | Sharp DK-KP80PH Specifications

MODEL
DK-KP80PH
SLIM MICRO SYSTEM
OPERATION MANUAL
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual
carefully. It will guide you in operating your SHARP product.
iPad, iPhone, iPod, iPod classic, iPod nano,and
iPod
touch
are
trademarks
of
Apple
Inc.,registered in the U.S. and other countries.
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed
to connect specifically to iPod, iPhone, or iPad respectively, and has been certified by the developer to meet
Apple performance standards. Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect
wireless performance.
Accessories
The following accessories are included.
Remote control x 1
(RRMCGA272AWSA)
Stand for iPad
x1
AM loop aerial
x1
FM aerial
x1
Dock Spacer
x1
“AA” size battery
(UM/SUM-3, R6,
HP-7 or similar) x 1
Special Note
Supply of this product does not convey a license nor imply any right to distribute content created with this product in
revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue-generating
streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution
systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact
discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for such
use is required. For details, please visit http://mp3licensing.com
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
*TINSEA369AWZZUU*|
TINSEA369AWZZ
11/8/29
DK-KP80PH_Front.fm
SHARP CORPORATION
11J R MW 1
Special Notes
● To prevent fire or shock hazard, do not expose this
appliance to dripping or splashing. No objects filled with
liquids, such as vases, shall be placed on the
apparatus.
● Do not turn the volume on to full at switch on. Listen to
music at moderate levels.
WARNINGS
● When the ON/STAND-BY button is set at STAND-BY
position, mains voltage is still present inside the unit.
When the ON/STAND-BY button is set at STAND-BY
position, the unit may be brought into operation by the
remote control.
● This unit contains no user serviceable parts. Never
remove covers unless qualified to do so. This unit
contains dangerous voltages, always remove mains
plug from the socket before any service operation and
when not in use for a long period.
Caution:
● This product is classified as a CLASS 1 LASER PRODUCT.
● This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain
access to the inside of the product. Refer all servicing to qualified personnel.
Precautions
■
● The AC power plug is used as a disconnect device and
shall always remain readily operable.
● Do not remove the outer cover, as this may result in
electric shock. Refer internal service to your local
SHARP service facility.
● The ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers,
tablecloths, curtains, etc.
● No naked flame sources, such as lighted candles,
should be placed on the apparatus.
● Attention should be drawn to the environmental aspects
of battery disposal.
● This unit should only be used within the range of 5°C 35°C (41°F - 95°F).
● The apparatus is designed for use in moderate
climates.
Warning:
The voltage used must be the same as that specified on
this unit. Using this product with a higher voltage other
than that which is specified is dangerous and may result
in a fire or other type of accident causing damage. SHARP
will not be held responsible for any damage resulting from
use of this unit with a voltage other than that which is
specified.
General
● Please ensure that the equipment is positioned in a
well ventilated area and ensure that there is at least 10
cm (4") of free space along the sides, top and back of
the equipment.
10 cm (4")
10 cm (4")
10 cm (4")
● Use the unit on a firm, level surface free from vibration.
● Place the unit at least 30 cm (12") away from any CRT
TV to avoid colour variations across the TV screen. If
the variations persist, move the unit further away from
the TV. LCD TV is not prone to such variation.
● Keep the unit away from direct sunlight, strong
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home computers,
facsimiles, etc.) which generate electrical noise.
● Do not place anything on top of the unit.
● Do not expose the unit to moisture, to temperatures
higher than
40°C (104°F) or to extremely low
temperatures.
● If your system does not work properly, disconnect the
AC power lead from the wall socket. Plug the AC power
lead back in, and then turn on your system.
● In case of an electrical storm, unplug the unit for safety.
● Hold the AC power plug by the head when removing it
from the wall socket, as pulling the lead can damage
internal wires.
■
Volume control
The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It is
advisable to avoid exposure to high volume levels. Do not
turn the volume on to full at switch on. Listen to music at
moderate levels. Excessive sound pressure from
earphones and headphones can cause hearing loss.
1
System connections
Make sure to unplug the AC power lead before making any connections.
FM aerial
External FM aerial
for better
reception (not
supplied)
Wall socket
(AC 220 - 240 V ~ 50/60 Hz)
AM loop aerial
■
Aerial connection
■
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS socket and
position the FM aerial wire in the direction where the
strongest signal can be received.
External FM aerial:
Use an external FM aerial (75 ohms coaxial cable) for
better reception. When an external FM aerial is used,
disconnect the supplied FM aerial wire.
Note:
Placing the aerial on the unit or near the AC power lead
may cause noise pickup. Place the aerial away from the
unit for better reception.
■
Demonstration mode
● The first time the unit is plugged in, the unit will enter
the demonstration mode.
● To cancel the demonstration mode, press the DEMO
button (remote control) during power stand-by mode.
The unit will enter the low power consumption mode.
● To return to the demonstration mode, press the DEMO
button again.
● If iPod or iPhone is docked, the unit will begin charging.
“Charge Mode” will be displayed. Demonstration mode
is invalid during charge mode.
AC power connection
After checking all the connections have been made
correctly, plug the AC power lead of this unit into the wall
socket.
Note:
Unplug the AC power lead from the wall socket if the unit
will not be in use for a prolonged period of time.
Remote control
■
● Do not use rechargeable battery (nickel-cadmium battery,
etc.).
● Installing the battery incorrectly may cause the unit to
malfunction.
● Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the
like.
Notes concerning use:
● Replace the battery if the operating distance is reduced or
if the operation becomes erratic. Purchase an “AA” size
battery (UM/SUM-3, R6, HP-7 or similar).
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the
direction of the unit if this occurs.
● Keep the remote control away from moisture, heat, shock,
and vibrations.
Battery installation
1 Open the battery cover.
2 Insert the supplied battery according to the terminal
indicated in the battery compartment.
When inserting or removing the battery, push it towards the
(–) battery terminals.
3 Close the cover.
Caution:
● Remove the battery if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
2
General control
■
Auto power off function
The main unit will enter the stand-by mode (when iPad, iPod
or iPhone is not connected) after 15 minutes of inactivity
during:
iPod :
Not docked.
Audio In : No detection of input signal.
CD :
In the stop mode or no disc.
USB :
In the stop mode or no media.
Note:
However, if iPod or iPhone is docked, the unit will begin
charging.
“Charge Mode” will be displayed.
■
Muting
The volume is muted temporarily when pressing the MUTE
button on the remote control. Press again to restore the
volume.
■
X-Bass control
When the power is first turned on, the unit will enter the extra
bass mode which emphasises the bass frequencies, and
“X-BASS” indicator will appear. To cancel the extra bass
mode, press the X-BASS button on the remote control.
■
■ Bass control
1 Press the BASS/TREBLE button to select “Bass”.
2 Within 5 seconds, press the VOLUME (+ or –) button to
To turn the power on
Press the ON/STAND-BY button to turn the power on.
adjust the bass. “X-BASS” indicator will disappear.
After use:
Press the ON/STAND-BY button to enter the power standby mode.
■
- 5 ↔ - 4........↔ + 4 ↔ + 5
Display brightness control
■ Treble control
1 Press the BASS/TREBLE button to select “Treble”.
2 Within 5 seconds, press the VOLUME (+ or –) button to
To dim the display brightness, press the DIMMER button on
the remote control.
Dimmer 1 (Display is dim).
adjust the treble. “X-BASS” indicator will disappear.
Dimmer 2 (Display gets dimmer).
Dimmer off (Display is bright).
■
- 5 ↔ - 4........↔ + 4 ↔ + 5
Volume auto fade-in
■
If you turn off and on the main unit with the volume set to 27
or higher, the volume starts at 16 and fades in to the last set
level.
■
Function
When the FUNCTION button on main unit is pressed, the
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
FM STEREO
CD
FM MONO
Volume control
Press VOL +/- to increase or decrease the volume.
■
AM
Direct key power on function
Audio In
When you press any of the following buttons, the unit turns on.
● iPod, CD/USB, AUDIO IN, TUNER on the remote control:
Selected function is activated.
●
/ button on the main unit: The unit turns on and
playback of the last function will start (CD, TUNER, USB,
iPod, AUDIO IN)
iPod
USB
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or the
AC power lead becomes disconnected.
i
3
Listening to the iPod, iPhone or iPad
Made for:
● iPod touch (4th generation)
● iPod touch (3rd generation)
● iPod touch (2nd generation)
● iPod touch (1st generation)
● iPod classic
● iPod nano (6th generation)
● iPod nano (5th generation)
● iPod nano (4th generation)
■
● iPod nano (3rd generation)
● iPod nano (2nd generation)
● iPhone 4
● iPhone 3GS
● iPhone 3G
● iPhone
● iPad 2
● iPad
1 Press the ON/STAND-BY button to turn the power on.
2 Press the USB button on the remote control or FUNCTION button
repeatedly on the main unit to select USB function.
3 Connect iPod, iPhone or iPad to the unit. “USB/iPod” will appear.
Caution:
Please update your iPod, iPhone and iPad unit to the latest
software version before using it. Please visit Apple’s
homepage to download the latest version for your iPod,
iPhone and iPad.
Notes:
● Charging terminal for iPod, iPhone and iPad:
Condition
DOCK
USB
USB function
YES
YES
(without iPod
or iPhone
docking)
Other function
YES
NO
(iPod / CD /
Tuner / Audio In)
Stand-by
YES
NO
File name
4 Press the / (USB / ) button to start playback.
Note:
Stop button ( ) is invalid during iPod, iPhone or iPad
playback
■
iPhone playback
● Sound will only switch from iPhone to the main unit
after authentication process is completed in
approximately 10 seconds.
● Incoming calls will pause the playback.
● Once the calls are answered, the conversation can only
be heard through the built-in iPhone speaker. Turn on
the iPhone speaker or undock the iPhone to start
conversation.
● The message “This accessory is not made to work with
iPhone” or similar, may appear on the iPhone screen
when:
- battery is low.
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
● This product is made for iPod, iPhone and iPad. To
prevent random interference when iPod, iPhone or
iPad is connected, the headphone output is disabled,
and “HP INVALID” will be displayed.
You may also experience brief audio interference
during incoming calls.
● The headphone output is switched off during inserting
iPod, iPhone and iPad unit. This is an Apple product
specification.
■
iPod, iPhone or iPad playback via USB
terminal
■
iPod and iPhone connection (Dock only)
Caution:
Unplug all accessories from the iPod or iPhone before
inserting it into the dock.
Note:
Docking station is not recommended for iPad connection.
1 Open the docking station for iPod
and iPhone by pulling up the cover.
iPod, iPhone and iPad connection via USB
terminal
2 Dock your iPod or iPhone into the unit.
1 Insert the connector to the iPod, iPhone or iPad.
iPhone (bottom)
iPhone
iPad
Dock connector
Connector
Dock for iPhone
2 Place the iPad to the stand for iPad.
iPad
Stand for iPad
3 Connect
the
iPod,
iPhone or iPad to the
unit via USB connector.
USB
4
Listening to the iPod, iPhone or iPad (continued)
For iPod nano or iPod touch :
For additional support, apply dock spacer (supplied) as shown.
Peel off
separator
Rib
■
To disconnect iPod, iPhone or iPad
Simply remove the iPod or iPhone from the docking station
or iPad connector from USB terminal. It is safe to do so
even during playback.
iPod
docking
cover
Caution:
● Unplug all accessories for the iPod or iPhone before
inserting it into the docking station.
● Stop button ( ) at main unit is invalid during iPod
function.
Dock spacer
■
1 Peel off the double sided tape separator.
2 Place the spacer between the two ribs of the iPod docking
Various iPod, iPhone and iPad functions
Function Main unit
cover as shown.
Dock/USB
■
iPod or iPhone playback
1 Press the ON/STAND-BY button to turn the power on.
2 Press the iPod button on the remote control or FUNCTION
Remote control
Dock
Operation
USB
Play
Press in the pause
mode.
Pause
Press in the
playback mode.
Track up/
down
Press in the
playback or pause
mode.
If you press the
button in the pause
mode, press the /
button to start the
desired track.
Fast
forward/
reverse
Press and hold
down in the
playback mode.
button repeatedly on the main unit to select iPod function.
3 Insert iPod or iPhone unit into the dock of main unit. “DOCK
OK” will appear.
4 Press the / (iPod
/ ) button to start playback.
Release the button
to resume
playback.
Repeat
____
Shuffle
■
Navigating the iPod, iPhone or iPad
menus
iPad unit. Press it again to go back to previous menu.
or ) button to select an item on the
menu and then press ENTER button.
Note:
When navigating the iPod, iPhone or iPad menu with remote
control, do not operate any of the buttons on the iPod or iPhone
unit. The volume level is adjusted by pressing the VOL (+ or –)
button on the main unit or the remote control. Adjusting the
volume on the iPod, iPhone or iPad units give no effect.
iPod, iPhone and iPad operations:
The operations described below depend on the generation iPod,
iPhone and iPad you are using.
System on operation:
When the main unit is powered on, the iPod, iPhone or iPad units
will automatically power on when docked or connected in the unit.
System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked iPod,
iPhone or connected iPad unit will automatically turn to stand-by
mode.
5
Press and hold
to toggle shuffle
mode.
Press to view the
iPod menu during
iPod function.
Menu
____
Enter
____
Press to confirm
the selection.
Cursor
Up/Down
____
Press to select the
iPod menu.
1 Press the MENU button to view the menu on iPod, iPhone or
2 Use the PRESET (
Press to toggle
repeat mode.
Listening to a CD or MP3/WMA disc
A. For example, to choose 13
1 Press the “10+” button once.
2 Press the “1” button.
3 Press the “3” button.
Selected track number
B. For example, to choose 130
1
2
3
4
Press the “10+” button twice.
Press the “1” button.
Press the “3” button.
Press the “0” button.
Notes:
● A track number higher than the number of tracks on the
disc cannot be selected.
● During random play, direct search is not possible.
To stop playback:
● Press the (CD ) button.
■
■
Various disc functions
Function
Disc playback
1 Press the ON/STAND-BY button to turn the power on.
2 Press the CD button on the remote control or FUNCTION
button repeatedly on the main unit to select CD function.
Main
unit
Operation
Play
Press in the stop mode.
Pause
Press in the playback
mode. Press the /
button to resume
playback from the
paused point.
Press in the playback
mode.
3 Press the OPEN/CLOSE button
to open the disc compartment.
4 Place the disc in the disc
Stop
compartment, label side front.
Remote
control
5 Press the OPEN/CLOSE button
to close the disc compartment.
6 Press the / (CD
/ ) button to start playback. After the
last track is played, the unit will stop automatically.
Track
up/
down
Caution:
● Do not place two discs in the disc compartment.
● Do not play discs of special shapes (heart, octagon, etc). It
may cause malfunctions.
● Do not push the disc compartment whilst it is moving.
● If the power fails whilst the compartment is open, wait until the
power is restored.
● If TV or radio interference occurs during CD operation, move
the unit away from the TV or radio.
● Be sure to place 8 cm (3") disc in the middle of the disc
compartment.
● Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
Fast
forward/
reverse
■
Repeat play
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press the PLAY MODE button repeatedly until “Repeat One”
appears. Press the / (CD / ) button.
To repeat all tracks:
Press the PLAY MODE button repeatedly until “Repeat All”
appears. Press the / (CD / ) button.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play” section on page 7
and then press the PLAY MODE button repeatedly until
“Repeat All” appears.
To cancel repeat play:
Press the PLAY MODE
button repeatedly until
“Normal” appears and
“
” disappears.
Caution:
After performing repeat play, be sure to press the (CD )
button. Otherwise, the disc will play continuously.
Notes for CD or MP3/WMA disc:
● When the end of the last track is reached during fast forward,
“END” will appear on the display and CD operation will be
paused. When the beginning of the first track is reached
during fast reverse, the unit will enter the playback mode (only
for CD).
● Rewritable multi-session discs with unfinished writing, can
still be played.
■
Press in the playback or
stop mode.
If you press the button in
the stop mode, press the
/ button to start the
desired track.
Press and hold down in
the playback mode.
Release the button to
resume playback.
Direct track search
By using the Numeric buttons, the desired tracks on the
current disc can be played.
Use the Numeric buttons on the remote control to select
the desired track whilst playing the selected disc.
● The Numeric buttons allow you to select up to number 9.
● When selecting number 10 or higher, use the “10+” button.
6
Listening to a CD or MP3/WMA disc (continued)
■
To cancel the programmed play mode:
During programmed stop mode, press the
(CD )
button. The display will show “Memory Clear” and all the
programmed contents will be cleared.
Programmed play (CD)
You can choose up to 32 selections for playback in the order
you like.
Adding tracks to the programme:
If a programme has been previously stored, the “MEM”
indicator will be displayed. Press the MEMORY button.
Then follow steps 2 - 3 to add tracks.
1 Whilst in the stop mode, press the MEMORY button on the remote
control to enter the programming save mode.
2 Press the numeric
button or
or
buttons on the remote
control to select the
desired track.
Notes:
● When the disc compartment is opened, the programme
is automatically cancelled.
● If you press the ON/STAND-BY button to enter the
stand-by mode or change the function from CD to
another, the programmed selections will be cleared.
● During the programme operation, random play is not
possible.
Selected track number
3 Press the MEMORY button to save the track number.
4 Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be
programmed. If you want to check the programmed tracks, press the
MEMORY button repeatedly. If you make a mistake, the programmed
tracks can be cleared by pressing the CLEAR button.
5 Press the
■
/ (CD
■
/ ) button to start playback.
To play back CD-R/RW.
Random play
1 Press the CD button, and load an MP3/WMA disc.
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
Press and hold the PLAY MODE button on the remote control
until “Random” appears. Press the / (CD / ) button.
To cancel random play:
Press the PLAY
MODE button again.
“RDM” indicator will
disappear.
Notes:
● If you press the
button during random play, you can
move to the track selected next by the random operation.
On the other hand, the
button does not allow you to
move to the previous track. The beginning of the track
being played will be located.
● In random play, the unit will select and play tracks
automatically. (You cannot select the order of the tracks.)
■
Procedure to playback MP3/WMA disc with
folder mode on
Press the FOLDER button and disc info will be
displayed.
MP3 indicator
WMA indicator
Total number of folder
TOTAL indicator
Total number of files
2 Press the PRESET (
or ) button to select desired
playback folder. (Folder mode on)
FOLDER
indicator
FOLDER number
Programmed play (MP3/WMA)
First track number
in the folder
3 Select desired file to be played back by pressing the
1 Whilst in the stop mode, press the MEMORY button to
or
enter the programming save mode.
button.
4 Press the
/ (CD / ) button. Playback will start and
file name will be displayed.
● Title, Artist and Album name are displayed if they are
recorded on the disc.
● In case of playback with the folder mode on, press
the PRESET ( or ) button, and the folder can be
selected even though it is in playback/pause mode.
It will continue playback/pause mode in the 1st track
of the selected folder.
● Display content can be changed by pressing the
DISPLAY button.
2 Press the PRESET (
or
) button on the remote
control to select the desired folder.
Then press the
or
button on the remote control
to select the desired tracks.
File name display
Folder display
3 Press the MEMORY button to save the folder and track
Counter display
number.
4 Repeat steps 2 – 3 for other folder/tracks. Up to 32
Album display
Title display
Artist display
tracks can be programmed.
5 Press the
/ (CD
Note:
If “Not Support” is displayed, it means “Copyright protected
WMA file” or “Not supported playback file” is selected.
/ ) button to start playback.
7
Listening to USB mass storage device/MP3 player
Caution:
At USB mode, once the iPod or iPhone is docked onto the
unit, the iPod or iPhone will automatically start charging.
‘iPod DOCK Charge Mode’ will be displayed. In order to
listen to any USB mass storage device / MP3 player, the
iPod or iPhone must be removed from the docking station.
2 Press the FOLDER button, and press the PRESET
( or ) button to select desired playback folder. To
start playback with folder mode on, go to step 4. To
change the playback folder, press the PRESET
( or ) button to select another folder.
3 Select desired file to be played back by pressing the
Notes:
1. Remove the USB terminal cover
before use. Keep it away from
children as it may be swallowed.
2. Cover the USB terminal if it is not
used for a long period of time to
prevent dust or rust.
or
button.
4 Press the / (USB / ) button. Playback will start and
the file name will be displayed.
● Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
● Display content can be changed by pressing the
DISPLAY button.
■
To remove USB memory device
1 Press the
(USB
) button to stop playback.
2 Disconnect USB memory device from the USB terminal.
Notes:
● SHARP will not be held liable for the loss of data whilst
the USB memory device is connected to the audio
system.
● Files compressed in MP3 and/or WMA format can be
played back when connected to the USB terminal.
● This USB memory’s format supports FAT 16 or FAT 32.
● SHARP cannot guarantee that all USB memory
devices will work on this audio system.
● USB cable is not recommended for use in this audio
system to connect to USB memory device. Use of the
USB cable will affect the performance of this audio
system. iPod, iPhone and iPad is not prone to this
condition.
● This USB memory cannot be operated via USB hub.
● The USB terminal in this unit is not intended for a PC
connection but is used for music streaming with a USB
memory device.
● External HDD-storage cannot be played back via USB
terminal.
● If the data inside the USB memory is large, it may take
longer time for the data to be read.
● This product can play WMA and MP3 files. It will
automatically detect the file type being played. If
unplayable file is played on this product, “Not Support”
is indicated and the file will be automatically skipped.
This will take a few seconds. If abnormal indications
appear on the display due to the unspecified file, turn
off the unit and then turn it on again.
● This product relates to USB mass storage devices and
MP3 players. It may however face some irregularities due
to various unforeseen reasons from some devices. Should
this happen, turn off the unit and then turn it on again.
● During CD function, MP3 player will not be charging.
Note:
This product is not compatible with MTP and AAC file
systems from USB mass storage device or MP3 player.
■
To play back USB/MP3 player with folder
mode off
1 Press the USB button on the remote control or
FUNCTION button repeatedly on main unit to select
USB function. Connect the USB memory device that
has MP3/WMA format files on the unit. When the USB
memory is connected to the main unit, the device
information will be displayed.
2 Select desired file to be played back by pressing the
or
button.
3 Press the
/ (USB / ) button. Playback will start
and the file name will be displayed.
● Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
● Display content can be changed by pressing the
DISPLAY button.
Note:
To pause playback:
Press the / (USB
■
/ ) button.
To play back USB/MP3 player with folder
mode on
The following functions are the same as CD
operations:
Page
Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programmed play (MP3/WMA) . . . . . . . . . . . . . . . . . . . 7
1 Press the USB button on the remote control or
FUNCTION button repeatedly on main unit to select
USB function. Connect the USB memory device that
has MP3/WMA format files on the unit. When the USB
memory is connected to the main unit, the device
information will be displayed.
Note:
● If USB memory device is not connected, “USB No
Media” will be shown on the display.
8
Listening to USB mass storage device/MP3 player (continued)
Notes:
● This unit only supports “MPEG-1 Audio Layer-3” format. (Sampling Frequency is 32, 44.1, 48kHz)
● Playback order for MP3 files may differ depending on the writing software used during file download.
● Bitrate which is supported by MP3 is 32~320 kbps, WMA is 64~160 kbps.
● For MP3/WMA files, please put “.MP3” “.WMA” extension. Files cannot be played back if there is no MP3/WMA
extension.
● Playlists are not supported on this unit.
● This unit can display Folder Name or File Name up to 32 characters.
● Maximum total number of MP3/WMA files is 65025.
● Total number of folders read is 999 including folder with non-playable file. However, the display shows only folder with
MP3 files.
● The display playback time may not be displayed correctly when playing back a variable bitrate file.
● The ID3TAG information supported are TITLE, ARTIST and ALBUM only. Title name, artist name and album name can
be displayed by pressing the DISPLAY button during file playback or pause mode.
● WMA meta tag also supports title, artist and album name which are recorded in WMA files. Copyright protected WMA
files cannot be played back.
Listening to the radio
■
Memorising a station
You can store 40 AM and FM stations in memory and recall
them at the push of a button. (Preset tuning)
1 Perform steps 1 - 3 in “Tuning”.
2 Press the MEMORY
button.
3 Within 30 seconds, press the PRESET (
or ) button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
4 Within 30 seconds, press the MEMORY button to store
■
that station in memory. If the “MEMORY” and preset
number indicators disappear before the station is
memorised, repeat the operation from step 2.
Tuning
1 Press the ON/STAND-BY button to turn the power on.
5 Repeat steps 1 - 4 to set other stations, or to change a
2 Press the FUNCTION button on the main unit or
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
Note:
The backup function protects the memorised stations for a
few hours should there be a power failure or the AC power
lead becomes disconnected.
TUNER button on the remote control repeatedly to
select FM Stereo, FM Mono or AM.
3 Press the TUNING (
or
) button on the remote
control to tune in to the desired station.
● Manual tuning:
Press the TUNING (
or
) button repeatedly to
tune in to the desired station.
● Auto tuning:
When the TUNING ( or
) button is pressed for
more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
■
To recall a memorised station
) button for less than 0.5
Press the PRESET ( or
seconds to select the desired station.
■
To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
Notes:
● When radio interference occurs, auto scan tuning may
stop automatically at that point.
● Auto scan tuning will skip weak signal stations.
● To stop the auto tuning, press the TUNING ( or
)
button again.
● When an RDS (Radio Data System) station is tuned in,
the frequency will be displayed first, and then the RDS
indicator will light up. Finally, the station name will
appear.
● Full auto tuning can be achieved for RDS stations
“ASPM”, see page 10.
To receive an FM stereo transmission:
● Press the TUNER button to select stereo mode and
“ST” indicator will be displayed. “
” and “ ” will
appear when an FM broadcast is in stereo.
● If the FM reception is weak, press the TUNER button to
extinguish the “ST” indicator. The reception changes to
monaural, and the sound becomes clearer.
1 Press the PRESET (
or
) button for more than 0.5
seconds. The preset number will flash and the programmed
stations will be tuned in sequentially, for 5 seconds each.
2 Press the PRESET (
or
) button again when the desired
station is located.
■
To erase entire preset memory
1 Press the ON/STAND-BY button to enter the stand-by mode.
2 Whilst pressing down the
button, press the ON/STANDBY button until “Tuner Clear” appears.
TUNING
9
Using the Radio Data System (RDS)
RDS is a broadcasting service which a growing
number of FM stations provide. These FM stations
send additional signals along with their regular
programme signals. They send their station names,
and information about the type of programme such as
sport, music, etc.
When tuned to an RDS station, “RDS” and the station
name will be displayed.
“TP” (Traffic Programme) will appear on the display when
the received broadcast carries traffic information, and “TA”
(Traffic Announcement) will appear whilst a traffic
information is on air.
“PTYI” (Dynamic PTY Indicator) will appear whilst the
Dynamic PTY station is received.
You can control the RDS by using the buttons on the
remote control only.
■
Information provided by RDS
Each time the RDS DISPLAY button is pressed, the
display will switch as follows:
Station name (PS)
Frequency
Programme type (PTY)
Radio text (RT)
■
No PTY
FM 98.80 MHz
No RT
3 After scanning, the number of stations stored in
memory will be displayed for 4 seconds, and then
“END” will appear for 4 seconds.
To stop the ASPM operation before it is complete:
Press the RDS ASPM button whilst it is scanning for stations.
The stations which are already stored in memory will be kept
there.
Notes:
● If the same station is broadcasting on different
frequencies, the strongest frequency will be stored in
memory.
● Any station which has the same frequency as the one
stored in memory will not be stored.
● If 40 stations have already been stored in memory, the
scan will be aborted. If you want to redo the ASPM
operation, erase the preset memory.
● If no station has been stored in memory, “END” will
appear for about 4 seconds.
● If the RDS signals are very weak, station names may
not be stored in memory.
● The same station name can be stored in different
channels.
● In a certain area or during certain time periods, the
station names may temporarily be different.
■
When tuning in to a station other than an RDS station or
to an RDS station which sends weak signal, the display
will change in the following order:
No PS
2 When an RDS station is found, “RDS” will appear
for a short time and the station will be stored in
memory.
Notes for RDS operation
If any of the following events occur, it does not mean
that the unit is faulty:
● “PS”, “No PS” and a station name appear alternately,
and the unit does not operate properly.
● If a particular station is not broadcasting properly or a
station is conducting tests, the RDS reception function
may not work properly.
● When you receive an RDS station whose signal is too
weak, information like the station name may not be
displayed.
● “No PS”, “No PTY” or “No RT” will flash for about 5
seconds, and then the frequency will be displayed.
Using the Auto Station Programme
Memory (ASPM)
Whilst in the ASPM operation mode, the tuner will
automatically search for new RDS stations. Up to 40
stations can be stored.
If you have already stored some stations in memory, the
number of new stations you can store will be less.
1 Press the TUNER button on the remote control or
FUNCTION button repeatedly on the main unit to
select TUNER function.
2 Press and hold down the RDS ASPM button on the
remote control.
1 After “ASPM” has flashed for about 4 seconds,
scanning will start (87.50 - 108.00 MHz).
10
Notes for radio text:
● The first 14 characters of the radio text will appear for
4 seconds and then they will scroll across the display.
● If you tune in to an RDS station which is not
broadcasting any radio text, “No RT” will be displayed
when you switch to the radio text position.
● Whilst radio text data is received or when the text
contents change, “RT” will be displayed.
Using the Radio Data System (RDS)
(continued)
■
Setting the clock (Remote control only)
To recall stations in memory
To specify programmed types and select stations
(PTY search):
You can search a station by specifying the programme type
(news, sports, traffic programme, etc.) from the stations in
memory.
1 Press the TUNER button on the remote control or
FUNCTION button repeatedly on the main unit to
select TUNER function.
2 Press the RDS PTY button on the remote control.
In this example, the clock is set for the 24-hour (0:00) display.
1 Press the ON/STAND-BY button to turn the power on.
2 Press the CLOCK/TIMER button.
3 Within 10 seconds, press the ENTER button. To adjust
“SELECT” and “PTY TI” will appear alternately for about 6 seconds.
the day, press the
or
button and then press the
ENTER button.
4 Press the
or
button to select 24-hour or 12-hour
display and then press the ENTER button.
3 Within 6 seconds, press
or
)
the PRESET (
button to select the
programme type.
Each time the button is pressed, the programme type will appear. If
the button is held down for more than 0.5 seconds, the programme
type will appear continuously.
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
4 Whilst the selected programme type is flashing (within
6 seconds), press the RDS PTY button again.
5 To adjust the hour, press the
or
button and then
press the ENTER button. Press the
or
button
once to advance the time by 1 hour. Hold it down to
advance continuously.
6 To adjust the minutes, press the
or
button and
then press the ENTER button. Press the
or
button once to advance the time by 1 minute. Hold it
down to advance the time by 5 minutes interval.
After the selected programme type has been lit for 2 seconds,
“SEARCH” will appear, and the search operation will start.
Notes:
● If the display has stopped flashing, start again from
step 2. If the unit finds a desired programme type, the
corresponding channel number will lit for about
8 seconds, and then the station name will remain it.
● If you want to listen to the same programme type of
another station, press the RDS PTY button whilst the
channel number or station name is flashing. The unit
will look for the next station.
● If no station can be found, “Not Found” will appear for 4
seconds.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “Clock” does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 14 for details.]
2 Perform “Setting the clock” from step 1 onwards.
If you select the traffic programme:
If you select the traffic programme (TP) in step 3, “TP” will
appear.
(This does not mean that you can listen to the traffic
information at that time.)
When the traffic information is broadcast, “TA” will appear.
11
Timer and sleep operation (Remote control only)
Timer playback:
The unit turns on and plays the desired source (CD,
TUNER, USB, iPod, AUDIO IN) at a preset time.
This unit has 2 types of timer: ONCE TIMER and DAILY
TIMER.
Once timer (“ ” indicator):
Once timer play works for one time only at a preset time.
12 When the preset time is reached, playback will start.
Daily timer (“DAILY” indicator):
Daily timer play works at the same preset time every day
that we set. For example, set the timer as a wake-up call
every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio
programme, and use the daily timer to wake up.
The volume will increase gradually until it reaches the
preset volume. The timer indicator will blink during
timer playback.
13 When the timer end time is reached, the system will
enter the power stand-by mode automatically.
Once timer:
The timer will be cancelled.
Daily timer:
The timer operates at the same time every selected day.
It will continue until the daily timer setting is cancelled.
Cancel the daily timer when it is not in use.
1 Set the daily timer.
2 Set the once timer.
Notes:
● When performing timer playback using another unit
connected to the USB terminal or AUDIO IN socket,
select “USB” or “AUDIO IN” in step 5.
● This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn
on or off. To stop the timer playback, follow step
“Cancelling the timer setting” of this page.
1 minute or more
Once timer
Daily timer
Start
■
Stop
Stop
Start
Timer playback
Checking the timer setting:
Before setting timer:
● Check that the clock is set to the correct time (refer to
page 11). If it is not set, you cannot use the timer
function.
● For timer playback: Plug in USB or load discs or dock
iPod to be played.
1 Turn the power on and press and hold down the
1 Press the ON/STAND-BY button to turn the power on.
2 Press and hold the CLOCK/TIMER button.
3 Within 10 seconds, press the
or
button to
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“Once” or “Daily”, and press the ENTER button.
3 Within 10 seconds, press the
or
button to select
“Timer Call”, and press the ENTER button.
Cancelling the timer setting:
CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“Once” or “Daily”, and press the ENTER button.
select “Once” or “Daily”, and press the ENTER button.
4 Within 10 seconds, press the
or
button to
select “Timer Set”, and press the ENTER button.
5 To select the timer playback source (CD, TUNER, USB,
iPod, AUDIO IN), press the
or
button. Press
the ENTER button.
When you select the tuner, select a station by pressing
the
or
button, and then press the ENTER
button. If a station has not been programmed, “No
Preset” will be displayed and timer setting will be
cancelled.
6 To adjust the day, press the
or
button and then
3 Within 10 seconds, press the
or
button to select
“Timer Off”, and press the ENTER button. Timer will be
cancelled (the setting will not be cancelled).
Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To
reuse the same setting, perform the following operations.
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“Once” or “Daily”, and press the ENTER button.
3 Within 10 seconds, press the
press the ENTER button.
or
button to select
“Timer On” , and press the ENTER button.
7 Press the ENTER button to adjust the hour. Press the
or
4 Press the ON/STAND-BY button to enter the power
button and then press the ENTER button.
8 To adjust the minutes, press the
or
stand-by mode.
button and
then press the ENTER button.
9 Set the time to finish as in steps 7 and 8 above.
10 Adjust the volume using the VOLUME control, and then
press the ENTER button. Do not turn the volume up too
high.
11 Press the ON/STAND-BY button to enter the power
stand-by mode. The “TIMER” indicator lights up and
the unit is ready for timer playback.
12
■
Sleep operation
The radio, compact disc, iPod, USB, Audio In can all be
turned off automatically.
1 Play back the desired sound source.
2 Press the SLEEP button.
3 Within 5 seconds, press the Numeric button to set the
time. (1 minute ~ 99 minutes)
Timer and sleep operation (Remote control only) (continued)
4 “SLEEP” will appear.
■
5 The unit will enter the power stand-by mode
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
automatically after the preset time has elapsed. The
volume will be turned down 1 minute before the sleep
operation finishes.
To use timer and sleep operation together
1 Set the sleep time (see above, steps 1 - 5).
To confirm the remaining sleep time:
Whilst “SLEEP” is indicated, press the SLEEP button.
2 Whilst the sleep timer is set, set the timer playback
(steps 2 - 9, page 12).
To cancel the sleep operation:
Press the ON/STAND-BY button whilst “SLEEP” is
indicated. To cancel the sleep operation without setting
the unit to the stand-by mode, proceed as follows.
Sleep timer
setting
Timer playback
setting
Desired time
1-99 minutes
1 Whilst “SLEEP” is indicated, press the SLEEP button.
Sleep operation will
automatically stop
2 Within 5 seconds, press the “0” button twice until
“SLEEP 00” appears.
End
time
Timer playback
start time
Enhancing your system
● Before plugging in or unplugging the headphone, reduce the
volume.
● Plugging in the headphone disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
The connection lead is not included. Purchase a
commercially available lead as shown below.
■
Listening to the playback sounds of
portable audio player, etc.
1 Use a connection lead to connect the portable audio
player etc. to the AUDIO IN socket. When using video
equipment, connect the audio output to this unit and the
video output to a television.
2 Press the ON/STAND-BY button to turn the power on.
3 Press the AUDIO IN button on the remote control or
FUNCTION button repeatedly on main unit to select
AUDIO IN function.
4 Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase the
volume of the connected device.
Note:
To prevent noise interference, place the unit away from the television.
Portable audio player, etc.
■
Headphones
● Do not turn the volume on to full at switch on and listen to
music at moderate levels. Excessive sound pressure from
earphones and headphones can cause hearing loss.
● Be sure your headphone has a 3.5 mm (1/8") diameter plug
and impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
Troublshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
■
■
● Playback does not
start.
● Playback stops in
the middle or is not
performed properly.
Symptom
General
Symptom
Possible cause
● The clock is not set to
the correct time.
● Did a power failure occur?
Reset the clock. (Refer page
11)
● When a button is
pressed, the unit does
not respond.
● Set the unit to the power standby mode and then turn it back
on.
● If the unit still malfunctions,
reset it. (Refer page 14)
● No sound is heard.
● Is the volume level set to “Min”?
● Are the headphones
connected?
CD player
Possible cause
● Is the disc loaded face
down?
● Does the disc satisfy the
standards?
● Is the disc distorted or
scratched?
● Playback sounds are ● Is the unit located near
skipped, or stopped
excessive vibrations?
in the middle of a
● Is the disc very dirty?
track.
● Has condensation formed
inside the unit?
13
Troublshooting chart (continued)
■
■
Remote control
Symptom
● The remote control
does not operate.
■
Possible cause
● Is the AC power lead of the
unit plugged in?
● Is the battery polarity
correct?
● Is the battery dead?
● Is the distance or angle
incorrect?
● Does the remote control
sensor receive strong
light?
● The radio makes
unusual noises
continuously.
■
■
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on
again.
2 If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
Possible cause
● Is the unit placed near the
TV or computer?
● Is the FM aerial placed
properly? Move the aerial
away from the AC power
lead if it is located nearby.
USB
■
Symptom
● Device cannot be
detected.
Possible cause
● Is there any MP3/WMA file
available?
● Is the device properly
connected?
● Is it an MTP device?
● Does the device contain
AAC file only?
● Playback does not ● Is it a copyright protected
start.
WMA file?
● Is it a false MP3 file?
● Wrong time display. ● Is Variable Bitrate file being
played back?
● Wrong file name
display.
● Is the File Name written in
Chinese or Japanese
characters?
■
● iPod, iPhone or
iPad will not
charge.
● “This accessory is
not made to work
with iPhone” or
“This accessory is
not supported by
iPhone” appears on
iPhone screen.
Factory reset, clearing all memory
1 Press the ON/STAND-BY button to enter the power
stand-by mode.
2 Whilst pressing down the OPEN/CLOSE button, press
the ON/STAND-BY button until “Clear All” appears.
Caution:
This operation will erase all data stored in memory
including clock, timer settings and tuner preset.
■
Before transporting the unit
Remove the iPod, iPhone, iPad, USB memory device and disc
from the unit. Then, set the unit to the power stand-by mode.
Carrying the unit with iPod, iPhone, iPad or USB memory
device left connected or discs left inside might damage the unit.
iPod, iPhone or iPad
Symptom
● No sound is
produced.
If problem occurs
When this product is subjected to strong external
interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
Tuner
Symptom
Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter on
the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no
disc in the unit until normal playback is possible (about 1
hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.
Possible cause
● The iPod, iPhone or iPad is
not playing.
● The iPod, iPhone or iPad is
not properly connected to
the unit.
● Is the AC power lead of the
unit plugged in?
● The iPod, iPhone or iPad is
not making full contact with
the connector.
● Using iPod (3rd generation).
● The iPod or iPhone is not
supported. Refer to page 4
for compatible models.
● The iPhone battery is low.
Please charge the iPhone.
● iPhone is not properly
docked.
■
Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
● Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
● Keep your discs away from direct sunlight, heat, and
excessive moisture.
● Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a CD
is dirty or does not play properly, clean it with a soft, dry
cloth, wiping straight out from the centre, along the radius.
YES
NO
Correct
14
Maintenance
■
Caution:
● Do not use chemicals for cleaning (petrol, paint thinner,
etc.). It may damage the cabinet.
● Do not apply oil to the inside of the unit. It may cause
malfunctions.
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
Specifications
As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of
production units. There may be some deviations from these values in individual units.
■
■
General
Power source
AC 220 - 240 V ~ 50/60 Hz
Power
consumption
Power on: 22 W
Power stand-by: 0.4 W (*)
Speaker
1-way speaker system
Speaker: 6.5 cm (2-1/2")
Speaker
maximum input
power
50 W/channel
Speaker rated
input power
25 W/channel
Dimensions
Width: 475 mm (18 - 11/16")
Height: 191 mm (7 - 1/2")
Depth: 83 mm (3 - 1/4")
Weight
2.5 kg (5.5 lbs.)
USB host interface ● Complies with USB 1.1 (Full
Speed)/2.0 Mass Storage
Class.
● Support Bulk only and CBI
protocol.
Support file
● MPEG 1 Layer 3
● WMA (Non DRM)
Bitrate support
● MP3 (32 ~ 320 kbps)
● WMA (64 ~ 160 kbps)
Other
● Maximum total number of
MP3/WMA files is 65025.
● Maximum total number of
folders is 999 INCLUSIVE of
root directory.
● The ID3TAG information
supported are TITLE, ARTIST
and ALBUM only.
● Supports ID3TAG version 1
and version 2.
File system
● Support USB devices with
Microsoft Windows/DOS/FAT
support
12/FAT 16/ FAT 32.
● 2 kbyte block length for sector.
( * ) This power consumption value is obtained when the
demonstration mode is cancelled in the power stand-by
mode. Refer to page 3 to cancel the demonstration mode.
■
Amplifier
Output power
■
PMPO: 100 W
MPO: 50 W (25 W + 25 W)
(10% T.H.D.)
RMS: 50 W (25 W + 25 W)
(10% T.H.D.)
RMS: 40 W (20 W + 20 W)
(1% T.H.D.)
Output terminals Headphones: 16 ohms
(recommended: 32 ohms)
Input terminals
■
USB (MP3 / WMA)
Audio In (audio signal):
500 mV/47 k ohms
CD player
Type
Single disc multi-play compact disc
player
Signal readout
Non-contact, 3-beam
semiconductor laser pickup
D/A converter
Multi bit D/A converter
Frequency
response
20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
15
Tuner
Frequency range
FM: 87.5 - 108 MHz
AM: 522 - 1,620 kHz
Preset
40 (FM and AM station)
For Australia and New Zealand customers
FOR LOCATION ENQUIRIES WITHIN
AUSTRALIA
REGARDING YOUR LOCAL
SHARP APPROVED SERVICE CENTRE
VISIT OUR WEBSITE AT
www.sharp.net.au
OR CALL SHARP CUSTOMER CARE
1300 135 022
(LOCAL CALL COSTS APPLY WITHIN AUSTRALIA)
SHARP CORPORATION OF AUSTRALIA PTY LTD
FOR LOCATION ENQUIRIES WITHIN
NEW ZEALAND
REGARDING YOUR LOCAL
SHARP APPROVED SERVICE CENTRE
VISIT OUR WEBSITE AT
www.sharp.net.nz
CONTACT YOUR SELLING DEALER/RETAILER
OR CALL
SHARP CUSTOMER SERVICES
TELEPHONE: 09 573 0111
FACSIMILE: 09 573 0113
SHARP CORPORATION OF NEW ZEALAND LIMITED
SPform019(AUGUST 2011)
For Australia and New Zealand customers
For U.K. and Ireland customers
NOTES FOR USERS IN THE U.K. AND IRELAND
The mains lead of this product is tted with a non-rewireable
(moulded) plug incorporating a 5A fuse. Should the fuse need to
be replaced, a BSI or ASTA approved BS 1362 fuse marked or
and of the same rating as above, which is also indicated on
the pin face of the plug must be used.
Always re t the fuse cover after replacing the fuse. Never use
the plug without the fuse cover tted.
In the unlikely event of the socket outlet in your home not being
compatible with the plug supplied, cut-off the mains plug and t
an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off
plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may
occur.
To t an appropriate plug to the mains lead, follow the instructions below:
Ensure that neither the brown nor the blue wire is connected to
the earth terminal in your three pin plug.
Before replacing the plug cover, make sure that:
If the new
d plug contains a fuse, its value is the same as
that removed from the cut-off plug.
The cord grip is clamped over the sheath of the mains lead
and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
SERVICE INFORMATION
In the unlikely event of your equipment requiring repair, please
contact the dealer or supplier from whom it was purchased. Where
this is not possible, please visit our web-site www.sharp.co.uk/
customersupport.aspx
Customers without internet access may telephone 0845
880 0512 during of ce hours (or (01) 676 0648 if telephoning
from lreland).
Please note; all calls will be charged at local rate.
IMPORTANT:
The wires in the mains lead are coloured in accordance with the
following code:
Blue
: Neutral
Brown : Live
Certain replacement parts and accessories may be obtained from
our main parts distributor.
As the colours of the wires in the mains lead of this product may
not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the plug
terminal which is marked N or coloured black.
The wire which is coloured brown must be connected to the
plug terminal which is marked L or coloured red.
In the unlikely event of this equipment requiring repair during the
guarantee period, you will need to provide proof of the date of
purchase to the repairing company.
Please keep your invoice or receipt, which is supplied at the
time of purchase.
WILLOW VALE ELECTRONICS LTD.
0121 766 5414
For U.K. and Ireland customers
Information on Proper Disposal
A.Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dustbin!
Used electrical and electronic equipment must be treated separately and in accordance with
legislation that requires proper treatment, recovery and recycling of used electrical and electronic
equipment.
Following the implementation by member states, private households within the EU states may
return their used electrical and electronic equipment to designated collection facilities free of
Attention: Your
charge*.
product is marked
In some countries* your local retailer may also take back your old product free of charge if you
purchase a similar new one.
with this symbol. It
*) Please contact your local authority for further details.
means that used
If your used electrical or electronic equipment has batteries or accumulators, please dispose of
electrical and
these separately beforehand according to local requirements.
electronic products
By disposing of this product correctly you will help ensure that the waste undergoes the necessary
should not be mixed treatment, recovery and recycling and thus prevent potential negative effects on the environment
with general
and human health which could otherwise arise due to inappropriate waste handling.
household waste.
2. In other Countries outside the EU
There is a separate If you wish to discard this product, please contact your local authorities and ask for the correct
collection system for method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the
these products.
dealer, even if you don't purchase a new product. Further collection facilities are listed on the
homepage of www.swico.ch or www.sens.ch.
B.Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You
might be charged for the costs arising from take-back and recycling. Small products (and small
amounts) might be taken back by your local collection facilities.
For Spain: Please contact the established collection system or your local authority for take-back of
your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct
method of disposal.
Information on Battery Disposal
The battery supplied with this product contains traces of Lead.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used
battery.
TERMS OF GUARANTEE
Sharp Electronics (UK) Ltd. (“Sharp”) guarantees to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below:1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does
not cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering with
the product, or repair other than by a Service Facility appointed by Sharp.
2. As this product is intended for private domestic use only, the guarantee will not apply if the product
is used in the course of a business, trade or profession.
3. T
Service Facility within one year from the date this product was purchased. Proof of purchase must
be provided.
4. The guarantee does not cover carriage costs, audio tapes, compact discs or batteries.
5. In the unlikely event of this product requiring repair, please contact the supplier from whom it was
purchased. Where this is not possible, please contact the Sharp Customer Information Centre on
the telephone number given below.
6. No person has any authority to vary the terms or conditions of this guarantee.
7. This guarantee is offered as an additional
rights in any way.
to your statutory rights, and does not affect these
If you have any dif
operating this product, or would like information on other Sharp products,
please telephone the Sharp Customer Information Centre on the number given below.
Sharp Customer Information Centre - Telephone 0845 880 0512
(or (01) 676 0648 if telephoning from Ireland)
Customer support website address - www.sharp.co.uk/customersupport.aspx
Download PDF

advertising