T H U R L B Y T... SHORTFORM CATALOGUE

T H U R L B Y   T... SHORTFORM  CATALOGUE
THURLBY THANDAR INSTRUMENTS
SHORTFORM CATALOGUE
Precision Measurement & RF Test Equipment
•
Digital Multimeters • Component Meters •
•
Current Measurement • Power Source Testing •
•
Frequency Measurement • RF Spectrum Analysis •
•
RF Signal Generation • Power & EMC Harmonics Analysis •
tti-test.com
tti.eu | tti.co.uk
Issue 3A - April 2010
1. Precision Measurement
Measurably better value
Product Range
Digital Multimeters - page 1
Bench-top multimeters with from 4¼ to 5½
digit resolution, all with true rms ac and
digital control interfaces.
Component Measurement - page 3
Precision LCR bridge, micro-ohm meter.
I-Prober Current Probe - page 4
Innovative probe for applications that include
non-contact measurement of currents in PCB
tracks.
Power Source Testing - page 5
Electronic DC Load for power supply and
battery testing. Proving unit for volt-sticks.
Precision measurement instruments
TTi has been designing and manufacturing precision
measurement instruments for nearly thirty years.
Expertise in precision analog design has enabled the
company to offer high performance products with advanced
features at attractive prices.
TTi offers instruments for the precision measurement of all
of the fundamental electronic parameters including voltage,
current, resistance, capacitance, inductance, power and
frequency.
The new I-Prober HPI current probe will enable the
measurement of current in situations where it was previously
not possible.
Frequency Measurement - page 6
Bench-top universal counter and handheld
frequency meter.
RF and EMC Test Equipment
page 7 onwards
Digital Multimeters
Bench-top DMMs versus hand-held
Low cost hand-held DMMs have replaced benchtop DMMs in many applications. Although the
performance of these meters may be sufficient for
some tasks, it is likely that most engineers will
regularly encounter measurement problems that
are beyond the capability of a hand-held unit.
An instrument intended for serious use
A TTi bench-top DMM is a substantial instrument.
It stays where you put it even with heavy test
leads connected. The tilt stand ensures that the
large display is always readable. The functions
buttons are large and the front panel is clearly
marked.
Sensitivity, Resolution and Accuracy
Compare the performance of any TTi bench-top
DMM with a good quality 4000 count hand-held
DMM of 0.3% basic dcV accuracy.
Longer scale length, greater sensitivity and higher
accuracy ensure that measurement uncertainty is a
full order of magnitude better.
TTi bench-top DMMs maintain good accuracy on
all functions including ac voltage, resistance and
current. For most hand-helds, the accuracies for
functions other than dc voltage are dramatically
poorer.
Wideband ac measurement and true RMS
Most hand-held DMMs have an ac frequency
response specified to below 1kHz. All TTi benchtop DMMs provide excellent accuracy on all ranges
throughout the audio band (40Hz to 20kHz) with a
3dB bandwidth extending well above this.
Most ac signals are not sinusoidal. However, most
hand-held DMMs incorporate a mean sensing
ac converter which only gives useful results on
sinusoids, those that do have a True RMS converter
often have insufficient bandwidth to cope with
complex waveshapes. All TTi bench-top DMMs
combine True RMS ac with sufficient bandwidth to
ensure accurate results.
Page 1
Digital Multimeters - Comparison Table
1604
Display Type
LED
Scale Length (Counts)
40,000
Dual Measurement
No
DC Voltage: Ranges
(5) 400mV to 1000V
Best Resolution
10µV
Basic Accuracy
0.08%
AC Voltage: Ranges
(5) 400mV to 750V
True RMS conversion
Yes
Frequency Response
0.08%
DC/AC Current: Ranges
(3) 4mA to 10A
Best Resolution
100nA
Resistance: Ranges
(6) 400W - 40MW
Best Resolution
10μW
Frequency
Yes
Capacitance
No
Smart Functions
3
Interfaces:
RS-232
Yes *
GPIB (IEEE-488)
No
Power Source
AC Line
PC and System connectivity
At some point most engineers are going to want to
connect their DMM to their personal computer to
provide automatic measurement control or importing
of data into a computer programme. Unlike a handheld DMM, all TTi bench-top DMMs include a fully
isolated RS-232 interface.
1705 & 1705-GP
Dual LCD
12,000
Yes
(5) 120mV to 1000V
10µV
0.04%
(5) 120mV to 750V
Yes
0.04%
(3) 1.2mA to 10A
100nA
(7) 120W - 20MW
10μW
Yes
Yes
12
Yes
Yes (GP version)
AC Line or Battery
1906 & 1906-GP
LED
210,000
No
(5) 200mV to 1000V
1µV
0.012%
(5) 200mV to 750V
Yes
0.012%
(6) 200µA to 10A
1nA
(6) 200W - 20MW
1μW
No
No
9
Yes
Yes (GP version)
AC Line
* RS232 interface on 1604 is only for use with the
optional PC-1604 control and data logging software.
Full technical details for all three multimeters is available
on the web site.
For full system applications, the 1705-GP and 1906GP also have a GPIB (IEEE-488) interface.
Functions & features of real value
Hand-held DMMs may offer a few “smart” features
but these are rarely well enough implemented to be
of real use.
TTi bench-top DMMs offer features which are of real
use and not just “gimmicks”. Features such as dual
Measurement & display, precision frequency measurement, dBm, data logging, power and VA, to mention
just a few.
For complete information on any product, click the product title bar to link directly to our web site
precision measurement - Digital
Measurably better value
Multimeters 2.
1604
Function
Ranges
Best Resolution
Best Accuracy
DC V
(5) 400mV - 1000V
10μV
0.08% ± 4 digits
AC V
(5) 400mV - 750V
100μV
0.5% ± 4 digits
Resistance (6) 400W - 40MW
10μW
0.1% ± 4 digits
DC I
(3) 4mA - 10A
0.1μA
0.1% ± 4 digits
AC I
(3) 1mA - 10A
1μA
0.1% ± 4 digits
Frequency (2) 4kHz to 40kHz
0.1Hz
0.01% ± 1 digit
Further measurement functions: Continuity. Diode Test.
Smart functions: Null (Relative), Hold, T-Hold, Min/Max.
Interface: opto-isolated bi-directional RS-232 interface. 9600 baud.
Power: 230V or 115V AC nominal 50/60Hz, adjustable internally.
Size & weight: 260 x 88 x 235 mm (WxHxD). 2.0 kg (4.4 lb)
DMM
The 1604 is a high quality 40,000 count
bench-top multimeter with a wide
range of features.
 4¾ digit bench-top multimeter
It offers automatic or manual ranging,
high resolution (10µV, 10mW) together
with current measurement up to 10A.
 True RMS ac functions
 0.08% basic dc-v accuracy
 Isolated RS-232 interface*
40,000 counts, auto or manual ranging
Accuracy and resolution, 0.08%, 10µV, 10mW
 Large and bright LED display (14mm/0.56”)
 True RMS ac functions, wide ac bandwidth
 Relative, T-Hold and Min-Max functions included
 Optional PC control and logging software


1705
Function
DC V
AC V
Resistance
DC I
AC I
Capacitance
Ranges
Best Resolution
(5) 120mV - 1000V
10μV
(5) 120mV - 750V
100μV
(6) 120W - 20MW
10μW
(3) 1mA - 10A
0.1μA
(3) 1mA - 10A
0.1μA
(5) 10nF to 100nF
10pF
Best Accuracy
0.04% ± 2 digits
0.2% ± 20 digits
0.08% ± 2 digits
0.1% ± 3 digits
0.3% ± 20 digits
2% ± 5 digit
Further measurement functions: Continuity. Diode Test. Frequency
Smart functions: Null (Relative), Hold, T-Hold, Min/Max, dB, Ax+B, % deviation, VA.
Logger: 100 readings. Interfaces: RS-232 standard. GPIB (IEEE-488) optional.
Power: 230V or 115V AC 50/60Hz, or 6 x C cells disposable or rechargeable.
Size & weight: 260 x 88 x 235 mm (WxHxD). 2.0 kg (4.4 lb)
DMM
The 1705 is a precision 4¼ digit bench
multimeter incorporating dual displays
and dual measurement technology.
 Dual measurement multimeter
The dual displays can be used either to
display one measurement in two units
(e.g. mV and dB) or to measure two
parameters simultaneously (e.g. dc-V
and ac-V).
 Built-in data logger
 0.04% basic dc-v accuracy
 Isolated RS-232 or GPIB
 AC line or battery operation
Dual 12,000 count LCD, auto/manual ranging
Accuracy and resolution: 0.04%, 10µV, 10mW
 Dual displays & ‘dual measurement’ technology
 True RMS ac functions, Frequency, Capacitance
 Wide range of computing functions e.g. Ax + B
 Model with GPIB (IEEE-488) interface available
 Mains and battery operation as standard


1906
Function
Ranges
Best Resolution
DC V
(6) 210mV - 1000V
1μV
AC V
(6) 400mV - 750V
10μV
Resistance (6) 400W - 40MW
1μW
DC I
(3) 4mA - 10A
1nA
AC I
(3) 1mA - 10A
10nA
Best Accuracy
0.012% ± 3 digits
0.2% ± 25 digits
0.019% ± 3 digits
0.08% ± 12 digits
0.37% ± 25 digits
Further measurement functions: Continuity. Diode Test.
Smart functions: Null (Relative), Hold, T-Hold, Min/Max, Ax + B, % deviation,
dB, Digital filterering. Logger: 100 readings, manual or automatic.
Interfaces: RS-232 standard. GPIB (IEEE-488) optional.
Power: 230V or 115V AC nominal 50/60Hz, adjustable internally.
Size & weight: 260 x 88 x 235 mm (WxHxD). 2.2 kg (4.8 lb)
DMM
The 1906 is a precision bench-top
multimeter offering both high
resolution and high accuracy.
 5½ digit bench-top multimeter
The precision is matched by a four
terminal ohms measurement.
 1µV, 1nA, 1mW resolution
It’s wide range of facilities include
many ‘smart’ calculation functions and
a data logger.
 Isolated RS-232 or GPIB
 0.012% basic dc-v accuracy
 True RMS ac functions
210,000 counts, auto or manual ranging
Accuracy and resolution: 0.012%, 1µV, 1mW
 Four terminal resistance measurement
 True RMS ac functions, wide ac bandwidth
 Wide range of computing functions included
 Automatic data logging functions include
 Digital filtering for improved noise rejection
 Model with GPIB (IEEE-488) interface available


For complete information on any product, click the product title bar to link directly to our web site
Page 2
3. Component Measurement - precision measurement
LCR400 LCR bridge
0.1% basic measurement accuracy
Three test frequencies of 100Hz, 1kHz and 10kHz
 Automatic component recognition
 Built-in 4 terminal component fixture
 Dual 5 digit high brightness displays
 Limits comparator with multiple pass and fail bins
 RS-232 interface for PC connectivity
 Optional SMD tweezers, Kelvin Clip leads, Windows
logging software

 0.1% basic accuracy

 Built-in component fixture
 Built-in limits comparator
 RS-232 interface
Measurably better value
Note: Full technical details are
available on the web site.
Note: accessories not to same scale as LCR400
The LCR400 is a high performance LCR meter
that offers an alternative to low-cost handheld
units or expensive system units.
Dual displays, automatic component recognition
and auto-ranging make it easy to use, while its
built-in test fixture and limits comparator make
it suitable for applications within the laboratory,
production or inspection areas.
Range and resolution limits:
Resistance: 0.1mW to 990MW
Inductance: 0.001µH to 9900H
Capacitance: 0.001pF to 99000µF
BS407 low Ohmmeter
High basic accuracy of 0.1%
Wide measurement range of 1µW to 20kW
 Current reversal switch for detecting thermal emf
 Current diversion switch for easy zero setting
 Four terminal measurement using Kelvin clip leads
 Battery operation with built-in charger
 Switchable 20mV clamp for ‘dry circuit’ testing
 0.1% basic accuracy

 1µW to 20kW range

 Kelvin clip connection leads
 Rechargeable battery operation
Note: Full technical details are
available on the web site.
The BS407 is fully optimised for the task of accurate measurement of low resistances
with a best resolution of 1µW.
It uses a Direct Current technique to measure true resistance, rather than the resistive
component of impedance which is shown by AC excited LCR bridges. The test current
for each range has been chosen to minimise heating of the sample under test while
being sufficient to minimise the effects of thermal emf and noise.
This gives much greater accuracy at low resistances than can be obtained from the
very low test currents used by general purpose high resolution multimeters.
Page 3
For complete information on any product, click the product title bar to link directly to our web site
precision measurement - Current
Measurably better value
Measurement 4.
I-Prober 520
New Product
The I-Prober 520 will be launched during 2010
for more information on this innovative product,
go to the TTi web site: tti-test.com/go/iprober
Current measurement from non-contact probing of conductor
Wide dynamic range of 5mA to 20A peak to peak
 Wide bandwidth of DC to 5MHz
 Low noise equivalent to <5mA rms
 Designed to meet safety requirements to 600V Cat II
 Suitable for connection to any oscilloscope
 High accuracy general purpose H-field probe
 Convertible into standard ‘closed magnetic circuit’ current probe
 Current measurement by simple
non-contact probing of PCB track
 DC to 5MHz bandwidth
 5mA to 20A dynamic range
 Low noise figure


The I-Prober 520 HPI* current probe is unlike any
other current measurement device available.
Calibrated measurement of current normally
requires the current to be passed through a closed
magnetic loop. Typically this is done using some
form of split clamp device. Whereas this is suitable
for individual wires, it is of no use for measuring
current in PCB tracks.
The I-Prober 520 is a compact hand-held probe
which is used with an oscilloscope. By placing the
insulated tip of the probe onto a PCB track, the
current flowing in the track can be observed and
measured.
* HPI stands for H-field Proximity Intensity
measurement, a technique developed by TTi
and Aim Instruments using a patented sensor
technology.
The I-Prober 520 is supplied with a
clip-on toroid assembly which converts it
into a closed magnetic circuit probe for
measuring current in a wire.
The toroid is open until the probe is
attached, allowing insertion of the wire
without disconnection.
The wide bandwidth, dynamic range and
low noise of the probe are retained.
For complete information on any product, click the product title bar to link directly to our web site
Page 4
5. Power Source Testing - precision measurement
Measurably better value
LD300 dc load
 300 watt dc electronic load
 Up to 80 volts or 80 amps
 CI, CR, CV and CP modes
 Built-in transient generator
Note: Full technical details are
available on the web site.
Versatile solution for testing dc power sources
Constant current, constant resistance, constant conductance,
constant voltage and constant power modes
 Wide voltage and current range, 0 to 80 volts and 0 to 80 amps.
 300 watts continuous dissipation at 40oC
 Low minimum operating voltage of <1V at 40A
 Ten turn controls for level setting
 Built-in transient generator with variable slew
 Current monitor output for waveform viewing
 Variable drop-out voltage for battery testing
 Analog remote control capability


The LD300 is an inexpensive electronic load
which is suitable for testing and characterising a
wide variety of dc power sources.
It can be used to investigate the behaviour
of many different types of power source such
as batteries, solar cells, fuel cells or wind
generators, as well as electronic power supply
units.
Its wide voltage/current range, multiple
operating modes and built-in transient generator
give it the versatility to offer test solutions from
the design laboratory through to the component
P240 proving unit
 Essential equipment for safety
compliance
 Long-life battery operation
 Belt-clip mountable
The P240 is a hand-held battery powered proving unit that provides a
nominal 240V dc, 2mA source intended for proving the integrity of neon
type test voltage indicators.
For safety compliance, voltage indicators should be checked for correct
operation from this known voltage source before and after every use.
Testing is performed by inserting the test probes of the neon tester into
two recessed “touch proof” terminals on the proving unit. Insertion of
the probes automatically turns the proving unit on thus eliminating the
need for an on-off switch.
Page 5
For complete information on any product, click the product title bar to link directly to our web site
Measurably better value
precision measurement - Frequency
Measurement 6.
TF930
0.001Hz to 3000MHz frequency range
 TCXO timebase with better than 1ppm stability
 Frequency, period, pulse width and totalise modes
 Reciprocal counting measurements
 High impedance measurement up to 125 MHz
 Low pass filter, attenuator and trigger level control
 AC or DC coupling, 1M/50W selection, polarity invert
 Large 10 digit LCD display with annunciators
 Operation from built-in rechargeable batteries
 Low power consumption
 Remote control and readback via USB

 DC to 3GHz frequency range
 Frequency, period, pulse width,
Note: Full technical details are
available on the web site.
ratio and event counter modes
 Rechargeable batteries
 USB interface included
The TF930 is a high quality bench/portable 3GHz universal frequency
counter which offers period measurement, frequency ratio, pulse
width and event counting.
It uses an advanced reciprocal frequency counting technique to
achieve high resolution at all frequencies. A dc coupled input enables
VLF measurements to be made (down to 1mHz). The timebase uses
a high quality TCXO crystal with a very low ageing rate. An external
reference can also be used.
The large 10 digit LCD has a full set of annunciators. Measurement
times can be set between 0.3 seconds and 10 seconds.
Pulse width measurements can be made from rising to falling or falling to rising edge with adjustable thresholds. A variable attenuator
is incorporated the input impedance is switchable between 1MW and
50W.
The instrument operates from internal rechargeable NiMH batteries
which give typically 24 hours operating life. The universal AC charger
supplied will recharge the batteries in less than 4 hours and can be
used for continuous AC operation.
Full remote control and read-back is provided via a USB interface.
PFM3000
3Hz to 3000MHz frequency range
 Frequency and period measurement
 High sensitivity at all frequencies
 Switchable low pass filter
 Continuous reciprocal counting measurement
 0.001mHz low frequency resolution
 Push-to-measure function with auto power-down
 Large 8.5 digit display with full range of annunciators

Note: Full technical details are
available on the web site.
The PFM3000 is the latest handheld
frequency counter from TTi offering
measurement up to 3GHz.
 3Hz to 3GHz frequency range
It provides high impedance
measurement up to 125MHz and
50W measurement up to 3000MHz,
with excellent sensitivity across all
frequencies.
 Continuous reciprocal measurement
 Frequency or period display
 Handheld format
 Long battery life
It can measure both frequency and
period and uses a continuous reciprocal
frequency counting technique which
gives high resolution and accuracy at all
frequencies.
Despite its wide frequency range the
PFM3000 has a low power consumption
enabling it to operate for many hours
from a disposable battery.
A push-to-measure capability is
provided to extend battery life when
continuous signal monitoring is not
required.
For complete information on any product, click the product title bar to link directly to our web site
Page 6
7. RF & EMC Test Equipment
Measurably better value
Product Range
RF Power Meters - page 7
TTi-Satori ST series USB linked RF and
microwave power meters up to 26.5GHz.
Spectrum Analyzers - page 8
PSA-T series low-cost handheld spectrum
analyzers, 1.3GHz and 2.7GHz.
Signal Generators - page 9
Synthesised RF signal sources offering
exceptional value for money, 1GHz and 2GHz.
Harmonics & Flicker Measurement - page 11
Compliance quality power and harmonics
analyzer and source for measurements to
EN61000-3-2 and EN61000-3-3.
Frequency Measurement
See Precision Measurement section
(page 6).
RF and EMC Test Equipment
RF Test
The rapid growth in the use of wireless communications
and the inclusion of RF elements into many electronic
designs has increased the need for RF test equipment.
The high cost of products from the major producers in this
area has led TTi to develop lower cost alternatives for the
essential RF tools such as signal generators and spectrum
analyzers.
RF products from TTi are designed to offer the essential
elements required by engineers at significantly lower costs.
EMC Test
Most countries have now implemented legislation requiring
products to comply with standards for radiated and
conducted emissions.
TTi has produced equipment capable of compliance quality
measurements, enabling users to self-certify for current
harmonics and flicker.
Satori ST Series
 USB linked power meters
 12.4GHz, 18.5GHz or 26.5GHz
Note: Full technical details are
available on the web site.
 –50 dBm to +20 dBm range
Model
ST124SMA
ST185SMA
ST265SMA
Frequency Range
10MHz to 12.4GHz
10MHz to 18.5GHz
10MHz to 26.5GHz
Size and weight:
34mm high x 43mm wide x 125mm long; 83 grams
 Very low power consumption
The TTi-Satori ST series power sensors are
complete miniature RF & Microwave power
meters. They contains a CPU which controls the
sensor, processes the measurement results and
operates the interface.
All measurement data and settings are
transmitted via a USB interface to and from a
PC. The supplied virtual power meter software
for Windows creates a classic microwave power
meter.
The power meter is controlled by the TTi- Satori
software loaded on a Windows PC. This is a
virtual power meter with basic measurement
functions for the PC workstation.
A software toolkit is supplied to control the
power sensors via the PC. It includes a DLL
(dynamic link library) for individualized use of the
entire sensor functionality with Windows and the
user interface.
Page 7
Three models 12.4GHz, 18.5GHz or 26.5GHz
 Measurement down to 10MHz
 Measurement range from –50 dBm to +20 dBm
 Replacement solution for conventional power meter and sensor combination
 Simple USB connection to laptop or PC
 Use multiple sensors on one computer
 Very low power consumption (50mA)
 No reference calibrator required
 Lightweight and easy to use
 Robust construction with excellent reliability
 Convenient for production test and field service

For complete information on any product, click the product title bar to link directly to our web site
Measurably better value
RF & EMC test equipment - Spectrum Analysis
8.
PSA-T series
Model
PSA1301T
PSA2701T
Frequency Range
150 kHz to 1300 MHz
1 MHz to 2700 MHz
Size and weight:
170mm high x 97mm wide x 47mm deep
495 grams total
The PSA1301T and PSA2701T are low-cost, highly
portable RF spectrum analyzers.
They incorporate the features most needed in a portable
spectrum analyzer, together with many additional
functions provided within the handheld computer.
150kHz to 1300MHz frequency range (PSA1301T)
1MHz to 2700MHz frequency range (PSA2701T)
 Resolution bandwidths of 280kHz or 15kHz (PSA1301T)
1MHz, 280kHz or 15kHz (PSA2701T)
 High resolution (480 x 320 pixel) TFT colour screen
 -96dBm typical noise floor at -20dBm reference level
 Measurement in dBm or dBµV
 Fully adjustable centre frequency and span in 1kHz steps
 Choice of centre/span or start/stop setting
 Zero span mode with AM and FM audio demodulation
 Sweep modes of normal, single, peak hold and average
 Reference waveforms displayed in contrasting colour
 Twin markers with readout of absolute & difference values
 Smart marker movement with selectable peak tracking
 Amplitude limit lines with editor and store/recall
 Unlimited storage for waveforms, set-ups and screens
 Data transfer to PC for analysis, documentation & printing
 More than 4 hours continuous operation from a charge
 Smaller and lighter than any other spectrum analyzer (weight less than 0.5kg)
plus:
 Handheld computer based facilities including word processing, spreadsheets, appointments, picture/video viewing, MP3, Web and Email via Bluetooth and WiFi
 Large range of third party programs available including many for engineering, science and mathematics
 True handheld spectrum analyzers
 1.3 GHz and 2.7 GHz models
 Half VGA colour screen
 Built-in handheld computer

to see a full product
information tour:
www.tti-test.com/psa
The small size, low weight and long battery life of
the PSA-T Series make it the ideal tool for RF field
measurements.
However, its surprisingly low cost provides every
engineer with the potential to own a spectrum
analyzer, whether they work in the RF field or not.
The PSA-T Series will find applications within
development, servicing and production as well as
field use.
For complete information on any product, click the product title bar to link directly to our web site
Page 8
9. Signal Generators - RF & EMC test equipment
Measurably better value
TGR1040
 1 GHz signal generator
 -127dBm to +7dBm
 RS-232, optional GPIB
 Low cost
Note: Full technical details are
available on the web site.
10MHz to 1000MHz frequency range
Accuracy better than 1ppm over 15oC to 30oC
 Ageing better than 1 ppm over one year
 Low phase noise and low leakage
 -127dBm to +7dBm amplitude, 0.1dB steps
 Amplitude entry in dBm or µV / mV
 FM modulation, internal or external
 Four line back-lit dot matrix LCD display
 Keyboard and rotary encoder control
 Non-volatile storage for 9 generator set-ups
 Full remote control through RS232 or optional GPIB
 Significantly lower cost than other synthesized RF generators


The TGR1040 is the low cost solution for RF
engineers who require a basic RF generator of
high stability and wide amplitude range.
It has good phase noise and low leakage and
offers FM modulation, internal or external.
TGR2050
 2 GHz signal generator
 -127dBm to +7dBm
 AM, FM & phase modulation
 RS-232 and GPIB standard
Note: Full technical details are
available on the web site.
150kHz to 2000MHz frequency range
10Hz frequency setability
 Locking to external frequency standard
 Accuracy better than 1ppm over 15oC to 30oC
 Ageing better than 1 ppm over one year
 Low phase noise and low leakage
 -127dBm to +7dBm amplitude, 0.1dB steps
 Amplitude entry in dBm or µV / mV
 FM, Phase and AM modulation, internal or external
 Keyboard and rotary encoder control
 Non-volatile storage for 9 generator set-ups
 Full remote control through RS232 and GPIB
 Exceptional price/performance ratio


The TGR2050 offers a wide frequency range
with a setability of 10Hz. It has 1ppm internal
stability and can be locked to an external
standard.
Modulation facilities of FM, Phase and AM are
included.
Page 9
For complete information on any product, click the product title bar to link directly to our web site
Measurably better value
RF & EMC test equipment - Signal
Generators/Power Meters 10.
TGR6000
NEW
Note: Full technical
details are available on
the web site.
10MHz to 6000MHz frequency range
Accuracy better than 1ppm over 15oC to 30oC
 Ageing better than 1 ppm over one year
 Low phase noise and low leakage
 -110dBm to +7dBm amplitude, 0.1dB steps
 Amplitude entry in dBm, µV / mV, or dBµV
 User compensation tables for specific test set-ups
 Fast stepping sweep with dwell times down to 10ms
 Internal or externally triggered sweep, lin or log, up or down
 List sweep of up to 1000 points of amplitude versus frequency
 Non-volatile storage for 12 generator set-ups and 16 sweep lists
 Compact half-rack 2U casing uses minimum bench space
 Full remote control through RS232, USB, LAN or optional GPIB
 Significantly lower cost than other 6GHz generators
 6 GHz signal generator
 -110dBm to +7dBm
 High speed sweep
 USB, RS-232, and LAN
optional GPIB


The TGR6000 is a highly cost effective solution
for engineers requiring a high quality generator
operating up to 6GHz.
No modulations are incorporated, but rapid
settling times enables a fast stepped sweep.
Level trim allows amplitude to be adjusted at
various frequencies to match the requirements
of specfic test set-ups.
List sweep enables up to 1000 points of
amplitude versus frequency to be defined.
For complete information on any product, click the product title bar to link directly to our web site
Page 10
11. Harmonics & Flicker Analysis - RF & EMC test equipment
HA1600A
 Compliance measurements to
EN61000-3-2 & EN61000-3-3
 Tabular and histogram display of
harmonics
 Continuous analysis with realtime graphical update
 Full power analyzer features
 PC software supplied
Measurably better value
Compliance quality current harmonics measurements to EN61000-3-2 when using
compliant source (such as AC1000A)
 Tabular and histogram display of harmonics
 Continuous analysis with real-time graphical update
 Compliance quality fluctuations and flicker measurements to EN61000-3-3
 Full power analyzer measuring Watts, VA, Vrms, Vpk, Arms, Apk, A-inrush, CF, THD, PF, Hz
 Real-time voltage and current waveform displays
 Wide range of national power connectors available
 Parallel printer port plus RS232 and USB interfaces
 Windows PC control and documentation software supplied

Note: Full technical details are
available on the web site.
The HA1600A is a fast, easy to use power and
harmonics analyzer with a large and high resolution
graphical display, capable of continuous real-time
analysis.
The HA1600A is intended primarily as a dedicated
harmonics and flicker analyzer for compliance
quality measurements, but it can also be used as a
general purpose power analyzer.
The unit is available with range of power connectors to suit different national standards.
A printer interface is included along with RS-232
and USB interfaces for PC connectivity.
It is suitable for both the product development environment, and for production line test verification.
AC1000A
 1 kW low-distortion source
 Suitable for EN61000-3-2
Note: Full technical details are
available on the web site.
The AC1000A is an innovative, low
cost, pure power source designed
specifically for use with a harmonics
analyser such as the TTi HA1600A.
It permits compliance quality
measurements to EN61000–3–2 in
situations where the quality of the
AC supply is poor or variable.
The AC1000A has a power rating of
1000 watts at 230 volts. Maximum
continuous rms current is 4.4A with
a peak current capability of 10A.
Page 11
For complete information on any product, click the product title bar to link directly to our web site
Test and Measurement Instruments from TTi
AIM & THURLBY THANDAR INSTRUMENTS
Measurably better value
Aim-TTi is the name of the combined organisation formed from
Aim Instruments and Thurlby Thandar Instruments.
The Aim-TTi logo will appear on an increasing amount of
promotional material and documentation from 2010 onwards.
About this Short Form Catalogue
Products included
This Precision Measurement and RF Test Equipment
catalogue is an extract from the main TTi short form
catalogue which covers all TTi product groups and can
be downloaded from the web site.
New product introductions and changes
TTi regularly introduces new products and some may
have been added since this catalogue was printed.
For the latest information please visit our web site.
Products are subject to continuous development and
changes to some detailed specifications or to cosmetic
appearance may have taken place since the catalogue
was printed.
Detailed product information
This catalogue contains only limited product
information.
The TTi Web Site
This catalogue provides only limited information
on each product.
Detailed product information is provided on the
TTi web site, together with support information
and price lists.
The international web site is: tti-test.com
This has the alternative web address: tti.eu
UK customers can also use: tti.co.uk
which is the web site of our UK sales division.
Customers in the USA should use: tti.us.com
which is the web site of our US sales division.
(Note that the leading www. is optional for all of
our web addresses)
Fully detailed information for each product is available
from the web site. Alternatively contact TTi or the
local distributor in your country to request detailed
information.
Product illustrations
The illustrations within this catalogue are
representative of the products at the time of
printing. The main illustration for each product is at
approximately 42% (linear) of actual size in order to
enable size comparisons.
Further illustrations within the product description
area are at a variable scaling to fit the available space.
About TTi
Excellence through experience
Thurlby Thandar Instruments is one of Europe’s
leading manufacturers of test and measurement
instruments.
The company has wide experience in the design and
manufacture of advanced test instruments and power
supplies built up over more than thirty years
TTi is based in the United Kingdom, and all products
are built at the company’s facility in Huntingdon, close
to the famous university city of Cambridge.
Traceable quality systems
TTi is an ISO9001 registered company
operating fully traceable quality systems
for all processes from design through to
final calibration.
ISO9001:2008
Certificate number FM 20695
For complete information on any product, click the product title bar to link directly to our web site
tti-test.com
Thurlby Thandar Instruments Limited
Glebe Road, Huntingdon, Cambridgeshire
PE29 7DR England (United Kingdom)
Contact for international customers:
Web: www.tti-test.com
Telephone: +44 (0)1480 412451
Faximile: +44 (0)1480 450409
Email: [email protected]
Contact for UK customers:
Web: www.tti.co.uk
Telephone: 01480 412451
Faximile: 01480 450409
Email: [email protected]
Issue 3A - April 2010
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement