Technical Manual - DCS-550M Master SERIES2 ver2

Technical Manual - DCS-550M Master SERIES2 ver2
TECHNICAL MANUAL for the
JACQUES DCS-550M SERIES II MASTER
Publication version 2 March 2003
Jacques Electronics Pty Ltd ABN 11 010 416 323
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
About this manual
This is the Technical Manual, used with the JACQUES DCS-550M Series 2 Master Station.
This document is only to be used by qualified JACQUES Technicians to make specific menu changes,
and in it describes the following:
Lists the operations and configurations of all the User-menus. Including…
•
•
Describes how to show and hide any one or more of the User-menus
Includes addition information not included in the Operating Manual on the User-menus:
o Door Call Answer
o Audio Mode
•
This Technical Manual does not include the following topics, as they are already included in
the separate JACQUES DCS-550M Operating Manual:
o How to make Calls
o How to Answer calls
o How to make Group calls
o How to adjust volumes
JACQUES ELECTRONICS PTY LTD
ABN 11 010 416 323
Copyright © 2003
The contents of this document may not be reproduced, stored in a retrieval system or transmitted in
any form by any means; electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of Jacques Electronics Pty Ltd. Jacques Electronics Pty Ltd reserves the right
to continually improve products by updating any equipment specifications, document context and
design styling. Always quote this manual publication version (found on the front cover), when
enquiring about any further product information.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
2
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
Contents
SECTION 1 – Overview
The DCS-550M Series 2 Master .................................................................4
Device Identification Codes ........................................................................5
Code Types..................................................................................................5
Power-up sequence......................................................................................7
SECTION 2 – Menu Operations
User-menus..................................................................................................8
Hidden User-menus.....................................................................................10
Enabling User-menus ..................................................................................10
Disabling User-menus .................................................................................11
Saving your selections.................................................................................12
CPU Radio...................................................................................................13
Sys Info .......................................................................................................14
Scroll Tag List.............................................................................................15
Remote Mode ..............................................................................................16
Auto Call End..............................................................................................18
Door Call Answer........................................................................................19
Set Date/Time..............................................................................................20
About the Time function .............................................................................20
Setting the RTC...........................................................................................21
Alarm Delay ................................................................................................23
Audio Mode.................................................................................................24
Relay Settings..............................................................................................25
Get Tags?.....................................................................................................26
Isolate Slave ................................................................................................27
Scrolling through the Isolated Slaves..........................................................28
De-Isolate Slave ..........................................................................................29
Aux Channel Set..........................................................................................30
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
3
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 1 – Overview
The DCS-550M Series 2 Master
The Jacques DCS-550M Series 2 Master is available as either a standalone or desktop Master
console. It is available as an option to the Jacques PCC-550M PC Master.
FIGURE 1 shows the front panel and switch layout for the Jacques DCS-550M Series 2 Master unit.
The main display comprises of a custom two lined LCD character display, sizing sixteen (16) large
characters, each measuring 8mm high x 5mm wide.
All user-function menus and calling information are clearly displayed on this screen.
FIGURE 1: Front panel layout of the DCS-550M Series 2 Master
5
1
2
4
3
User controls and functions:
1. Large LCD display, backlit for easy viewing
2. Sixteen user pushbuttons
3. Internal Electret Microphone
4. Eight function pushbuttons
5. Internal water-resistant speaker
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
4
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 1 – Overview
Device Identification Codes
The DCS-550M Series 2 Master displays Identification Codes that are used to represent Devices (see
FIGURE 2).
Devices are attached Intercom Slaves or Accessories that make up the JACQUES Intercom System,
and are individually controlled by the Master.
Every JACQUES Device has to be registered within the operating software by means of Identification
Codes. These codes are critical for correct Device identification and operation within the Jacques
intercom system and consist of four different individual codes:
FIGURE 2
The four different codes, as displayed on the
LCD screen.
“CELL 1” = Device Descriptor
“3” = Indicates the 3rd Tag on the list
“130” = Device Tag number
“Slave” = Device Class type
Code Types
1/ Descriptor (Example: CELL 1)
A Descriptor is another software address identifier code used to identify the Device. They are
displayed on the LCD screen.
It is text up to 16 characters long (to fit within the 16-character LCD screen size), stored inside the
EEPROM memory chip located on the actual Pro Slave PCB, or inside the Concentrator unit (when
using Concentrator Slaves).
Descriptors are NOT changeable by the Operator and can only be changed by a Technician from the
Setup menu (see separate JACQUES PC Master Technical Manual), and only from a Higher-Level
Jacques PCC-550M PC Master.
2/ List Tag (Example: 3)
List Tag numbers, are numbers between 1 and the last Tag found in the networked intercom system.
They are a counter value that simply lists the place a Tag is within the Tags list. Therefore, as you
scroll through the Tags, this number will increment or decrement accordingly. Every Device has a
different List Tag number.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
5
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 1 – Overview
Code Types (continued)
3/ Tag (Example: 130)
A Tag can be described as one of the software address identifier codes, to the rest of the system.
The Tag is stored inside the EEPROM memory chip, located on the actual Concentrator-type Slave
PCB or inside the Concentrator unit (when using Concentrator-type Slaves).
They are displayed on the LCD screen.
Tags are NOT changeable by the Operator and can only be changed by a Technician from the Setup
menu (see separate JACQUES PC Master Technical Manual), and only from a Higher-Level
Jacques PCC-550M PC Master.
4/ Device Class (Example: Slave)
Device Class numbers, are numbers between 0 to 255 inclusive that are given to a Jacques Device.
They are used to describe the type of Jacques Device that is used with that specific Tag number,
described in one of the following ways: (see TABLE 1)
TABLE 1 - Device Classes
JACQUES ELECTRONICS DEVICE CLASSES and DISPLAYS
CLASS #
JACQUES DEVICE TYPES
LCD DISPLAY
1
2
3
4
5
6
7
8
Any other number
Slave
CPU
Printer
Audio recorder Interface
24 way I/O card
Slave Concentrator
PA Amplifier
Door / Gate Slave
Any other Device
Slave
CPU
Printer
Recordr
IO24
Concent
PA Amp
DoorSlv
<displays CLASS #>
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
6
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 1 – Overview
Power-up sequence
The DCS550M Series 2 Master automatically runs through a special Power-On-Self-Test (POST)
routine every time the unit is first switched on. This ensures that it sees all other connected devices
within the network intercom system and that all available connected devices and their tags are
correctly initialized and tested.
Switch on the power to the DCS-550M series 2 Master. The POST test begins….
Displays software version number
Finds the current time from the intercom Master
Finds the CPU code version
System ready for operation
Goes into Remote mode or Idle mode, depending on the
user settings from the Remote mode menu
Idle mode
Remote mode
The Master will either go into Remote or Idle modes, depending on the operator savings.
Once the Master shows the System Idle screen, (FIGURE 3) the operator can select any of the
enabled function menus. (See Section 3)
FIGURE 3: DCS-550M Master System Idle mode
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
7
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Important Note:
Some of the function menus shown here in the User-menu list MAY NOT BE ENABLED on your
DCS-550M Master.
If they are not enabled, they will not appear when you scroll through the menu list and are known
as “Hidden-menus”.
User-menus
The DCS-550M Series 2 Master has an internal menu-select type operation. These menus are selected
and used by the Operator to control all of its many functions and calling control.
To enter the menu options, press the MENU key from the System Idle screen (FIGURE 4) and then
use the UP and DOWN arrow keys to find the menu you require.
FIGURE 4:
To display the menus, press the MENU
key from the System Idle screen.
CPU Radio
01/01/2001 12:00
Then use the UP DOWN keys
to scroll through the different
User-menus.
Press the ENTER key to
enter the selected menu
Channel OFF
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
8
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
There are thirteen (13) User-menus available in the DCS-550M Master Series 2 software. They are:
CPU Radio
This menu switches ON or OFF the two Auxiliary audio channels, which can be heard
through the DCS-550M Master’s internal speaker.
Sys Info
This menu shows the current Master version software loaded and the Master controller
version that it is connected to.
Scroll Tag List
This menu displays all current and active Tags (Slaves, Masters and other Devices) that
are connected to the Master. This is a viewer only function and no changes can be made
to the Tags from this menu.
Remote Mode
This menu enables or disables the Remote mode. Once in Remote mode, the Master is
completely controlled by the next Higher-Level Master. All incoming calls will then be
diverted to that Higher-Level Master, after a selection of preset times.
Auto Call End
This menu is used to set the time that a call will automatically end, if no further call
activity is detected.
Door Call Answer
This menu allows Door Slave Stations to be used within the intercom system. DoorSlaves are usually only used with third-party security and monitoring systems.
Set Date/Time
This menu allows the operator to change the RTC’s Time and Date locally. However, the
time and date will automatically be updated from a Higher-level Master (if used).
Alarm Delay
This menu is used to set the properties of the “Tamper Alarm” and “Button Stuck”
features that are built into the JACQUES RS485 Slave Stations.
Audio Mode
This menu is used to set the HandsFree properties of the Master’s internal microphone.
Relay Settings
This menu is used to set the Relay switching properties, which are located on the Slaves.
Get Tags?
This menu allows the operator to get Tag, Descriptor and Class ID information from the
connected Devices within the Intercom System.
Isolate / De-Isolate Slave
This menu allows the operator to Disable or Isolate selected Slaves from the intercom
system. When a Slave is Isolated, it is effectively disabled from the system, until it is
Enabled again (De-Isolate) from this same menu.
Aux Channel Set
This menu allows the operator to change the individual Auxiliary audio channels and
speaker volume levels of connected JACQUES Slaves.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
9
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Hidden User-menus
Hidden User-menus are those User-menu options that are not shown (hidden) within the User-menu
list. They can be changed from disabled (hidden), to enabled (shown).
Hidden menus allow the versatility of custom-made functions that specific customers require,
providing the advantages of easier operation (less menus to setup and use), and the benefit to upgrade
and expand later.
Enabling User-menus
This function allows the Operator to Enable (show) all twelve User-menus.
To show and use all of the User-menu options (all twelve of them), simply press the # - 1 - # keys,
from the System Idle screen.
If there were any previous hidden menus, they are now reset to be viewable (not hidden).
FIGURE 6. Enabling all user-menus.
Make sure that the screen is in the
System Idle mode before
changing any user-menu options.
To Enable and Show all
user-menu options,
press the # - 1 - # keys
This screen is displayed for
about a second to confirm
that all the user-menus are
now able to be displayed.
Show_all = 1
Press the MENU key and scroll
with the UP and DOWN keys to
see all twelve of the User-menus.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
10
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Disabling User-menus
This function allows the Operator to Disable (hide) selected User-menus. Any one (or all) of the User
menus can be hidden from the operator. Press the # - 0 - # keys from the System Idle screen.
FIGURE 7. Hiding selected user-menus.
Make sure that the screen is in
the System Idle mode before
changing any menu options.
This screen is displayed for
about a second to confirm
that the selected user-menus
are now ready to be hidden.
Enable the hide menu select
mode by pressing
the # - 0 - # keys
Show_all = 0
Press the MENU key and use the UP DOWN keys to
find the menu(s) required be hidden.
In this example, the CPU Radio menu is selected.
CPU Radio
01/01/2001 12:00
Enable the menu (CPU Radio) as a hidden menu:
Press the * key, to Enable.
A “!” is displayed in the top right-hand corner of the screen.
(Press the * key again will Disable. Additional presses toggle.)
CPU Radio
!
01/01/2001 12:00
Options Saved
Save the menu (CPU Radio) as a hidden menu:
Press the A key to Save.
After the hidden menus have
been selected, disable the hide
menu select mode by again
pressing the # - 0 - # keys
Press the MENU key to view the
new user-menus. It will now not
display any hidden menus.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
11
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Saving your selections
The following user-menus require the operator to select one of a multiple choice function list.
• CPU Radio
(Channel Off, Channel 1, Channel 2)
• Remote Mode
(Disable REM key, Disable AutoRem, AutoRem 10min, AutoRem
2min, AutoRem 12sec)
• Auto Call End
(Disable AutoEnd, AutoEnd 2min, AutoEnd 10min, AutoEnd 30min)
• Door Call Answer
(Never, Always, Special)
• Alarm Delay
(Disable Alarm, 20min Delay, 10min Delay, 2min Delay, No Delay)
• Audio Mode
(HandsFree Off, HandsFree On)
When you enter one of the above User-menus, select the option required and then save that option by
pressing the MENU key and then the A key (FIGURE 8)
FIGURE 8: Saving the user-menu settings.
Select your preferred user-menu option settings, from the individual menus.
Press MENU key
Press A key
Your settings have now been saved into the Master’s internal Flash ROM, and they will not need to be
reprogrammed the next time this console is switched on.
System Idle screen
Press the END key to return to the
System Idle screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
12
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
CPU Radio
The CPU Radio menu (FIGURE 9) is used to change the two different Auxiliary audio channels.
These audio channels can be heard through the internal speaker of the Master.
By using the UP and DOWN keys, the operator can select between enabling Auxiliary audio channel
1, Auxiliary audio channel 2, or no channels (both channels off – no audio).
Once selected, press the ENTER key to save the selection and then press the END key to return back
to the System Idle screen.
NOTE: If your selection cannot be heard, press the UP key to adjust the channel volume.
FIGURE 9: CPU Radio menu option
Use the UP DOWN keys to select the CPU Radio menu option.
Press ENTER to begin.
CPU Radio
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Channel Off
(Both audio channels off – no audio).
Channel Off
Channel 1
Use the UP DOWN
keys to scroll through
the choices.
Channel 2
Press the ENTER key to
save the setting and return
to the CPU Radio
screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
13
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Sys Info
The Sys Info menu (FIGURE 10) shows the current Master version software loaded as well as the
Master controller version used. This is used to identify current operating software versions.
Example of Sys Info screen display. This may be different, due to software upgrades.
FIGURE 10: Sys Info menu option
Use the UP DOWN keys to select the Sys Info menu option.
Press ENTER to begin.
Sys Info
01/01/2001 12:00
Display shows Master console version, as well as
Master controller version
Console 1.00
Master 2.2.83
Press the END key to return to
the System Idle screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
14
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Scroll Tag List
The Scroll Tag List menu (FIGURE 11) is used to view all Slaves, Masters and other Devices that
are connected to the Master unit. This menu functions as a viewer only and NO changes can be made
to the Tags. Once in the Scroll Tag List menu, the operator can scroll through the Devices by using
the UP and DOWN keys.
Press the END key to return to the Scroll Tag List screen. Press the END key (again) to return to
the System Idle screen.
FIGURE 11: Scroll Tag List menu option.
Use the UP DOWN keys to select the Scroll Tag List menu option.
Press ENTER to begin.
Scroll Tag List
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Use the UP, DOWN keys to scroll
through the Tags.
L1 MASTER
1:2 CPU
Examples only.
Actual content will be different to yours.
L2 MASTER
2:32 CPU
CELL 1
3:131 Slave
Press the END key to return
to the Scroll Tag List
screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
15
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Remote Mode
In a multi-Master intercom system, there may be times when a Master station will be left unattended,
leaving some incoming calls unanswered.
The Remote Mode menu (FIGURE 12) allows the choice of those incoming unanswered calls to
(after a preset time has passed) be automatically diverted to the next higher-level Master.
When first switched on, the Master will either automatically go into either remote or idle modes,
depending on the options saved by the operator. For more information about remoting, see next page.
• When the Master is first turned on, it will either automatically go into either remote or idle modes,
•
•
•
•
depending on the options saved by the operator.
Press the REM or END key to turn-off the remote function (if enabled).
To disable the remote function completely, select Disable REM Key option from the menu
selection.
To otherwise enable the remote function, press the REM key.
The AutoRem 10 min, AutoRem 2 min and AutoRem 12 sec, menu options are
selected as the amount of time that passes on an unanswered incoming call, before the Master
automatically goes into remote mode.
FIGURE 12: Remote Mode menu option.
Use the UP DOWN keys to select the Remote Mode menu option.
Press ENTER to begin.
Remote Mode
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Use the UP, DOWN
keys to select the
following different
selections
These settings determine the
amount of time that passes on
an unanswered incoming call,
before the Master automatically
goes into remote mode.
Disable AutoRem will
disable this function.
Disable REM key
This setting is used to
disable the REM key on
the front panel of the
Master, stopping the
operator to turn-on/off the
remote function.
Disable AutoRem
AutoRem 10 min
AutoRem 2 min
AutoRem 12 sec
Press the ENTER key to
save the setting and return
to the Remote Mode
screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
16
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Remote Mode (continued)
In a multi-Master intercom system and a Master is remoted, then that Master’s operations are no
longer controlled by the operator. The calling operations are now effectively disabled. All Slaves and
Devices are all now controlled from the next-level up Master.
The following diagrams illustrates this.
FIGURE 13 shows the operators signal path between three level Masters, all are in Remote Off mode.
This allows all three Masters to individually operate and control its own level Slaves and Devices.
FIGURE 14 shows the new operators signal path between the same Masters, however the Level 2
Master is now in Remote On mode. The operators signal path has now changed.
Level 3 Master now controls Level 3 Slaves and Devices (as before) as well as all of Level 2 Slaves
and Devices (because Level 2 is in Remote On mode). Level 1 Master still controls Level 1 Slaves
and Devices (as before).
FIGURE 13
FIGURE 14
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
17
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Auto Call End
The Auto Call End menu (FIGURE 15) is used to automatically disconnect an already connected
call. It disconnects after a preset time has passed and that there is no call activity detected.
FIGURE 15: Auto Call End menu option.
Use the UP DOWN keys to select the Auto Call End menu option.
Press ENTER to begin.
Auto Call End
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Use the UP, DOWN
keys to select the
following different
selections
Disable AutoEnd
AutoEnd 2 min
AutoEnd 10 min
AutoEnd 30 min
These settings determine
the amount of time that
passes on an already
connected call, before the
Master automatically
disconnects that call.
Disable AutoEnd will
disable this function.
Press the ENTER key to
save the setting and return
to the Auto Call End
screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
18
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Door Call Answer
The Door Call Answer menu (FIGURE 16) is used to configure the way the Master answers Door
Slaves.
Door Slaves are normally controlled by third-party security management systems, however they can
also be answered by Jacques Masters, just like a normal Slave.
FIGURE 16: Door Call Answer menu option.
Use the UP DOWN keys to select the Door Call Answer menu option.
Press ENTER to begin.
Door Call Answer
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Use the UP, DOWN keys to
select the following different
selections
Never
Press the ENTER key
to save the setting and
return to the Door
Call Answer
screen.
Always
Special
•
•
•
Never: When this option is selected, the Master will never be able to answer incoming calls
from Door Slaves. (Door Slave answering is disabled)
Always: When this option is selected, the Master will always be able to answer incoming
calls from Door Slaves, just like answering normal Slaves. Answer the incoming Door Slave
call, by pressing the ENTER key.
Special: When this option is selected, the Master will be able to answer incoming calls
from Door Slaves, however the operator will need to use a different answer key sequence.
Answer the incoming Door Slave call, by first pressing the star (*) key and then by pressing
ENTER key.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
19
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Set Date/Time
This Section covers the following key areas of maintaining the Master’s correct time:
• About the Time function
• Setting the RTC
About the time function
The DCS-550M Series 2 Master has an inbuilt Real Time Clock (RTC) function built in.
The RTC is a self-oscillating clock that has an internal back up battery, able to maintain its correct
time for a few days without power.
Single-Level Intercom Systems
In a single-level Intercom System, the internal RTC maintains the correct time.
The RTC inside the DCS-550M Master can be correctly set (date and time) from the Set Date/Time
menu. (refer to the DCS-550M Master Operator Manual for details).
FIGURE 17:
The DCS-550M Master’s internal RTC maintains the correct time, in a single-level Intercom System.
Multi-Level Intercom Systems
When using multiple Levels in a single Intercom System, generally more than one Master is used.
In all multi-level systems, the highest-level master will ultimately control all other Master’s clocks,
regardless of their own RTC clock settings.
FIGURE 18:
Shown here is a three-level
Intercom System, with a PC as
the Highest Level Master.
The PC has an internal RTC and
sends out a continuous signal that
synchronizes all other Masters
below, to it.
The result is that all three
Masters have exactly the same
time, regardless of what the
individual RTC’s are set to inside
the other two Masters.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
20
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Set Date/Time (continued)
Multi-Level Intercom Systems, with High-Level-Interface (HLI)
A High-Level-Interface is a third party Control or Security System, added to a JACQUES Intercom
System, located above the Highest Level Master. The HLI is able to control all other Masters and
connected Devices.
In a HLI featured Intercom system, it is the HLI’s internal RTC clock that will synchronize all other
Masters below, to it.
FIGURE 19:
Shown here is a two-level Intercom
System, with a third-party HighLevel-Interface (HLI), used to control
all other Masters below it.
The HLI has an internal RTC and
sends out a continuous signal that
synchronizes all other Masters below,
to it.
The result is that all the Masters have
exactly the same time, regardless of
what the individual RTC’s are set to
inside the other Masters.
Setting the RTC
*Important:
To set the Date/Time function, the REM key must be disabled. To do this,
1. Select the Remote Mode from the user menus.
2. Select Disable REM key.
3. Press the END key to save and exit.
The following FIGURE 20 (next page) shows how to set the Date and Time into the RTC.
The current Date and Time can be set and saved to the RTC inside the Master.
This is done in single-Level Intercom Systems, or when the RTC is not automatically updated by
High-Level Masters or other High-Level-Interfaces. (The Master relies on the internal RTC for the
correct Date/Time.)
After the Time and Date has been correctly set (by the UP / DOWN arrow keys and ENTER to scroll
through the Minute/Hour/Year/Month/Day), the Operator can check the settings by retrieving the
Date/Time by pressing the C key.
The Operator can save the Date/Time into the RTC by pressing the A key.
Press the END key to exit.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
21
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Set Date/Time (continued)
FIGURE 20: Set Date/Time menu option. (set from the Highest-Level Master)
Use the UP DOWN keys to select the Set Date/Time menu option.
Press ENTER to begin.
Set Date/Time
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Use the UP, DOWN
keys to enable the
different selections of:
Seconds,
Minutes,
Hours,
Year,
Month and Day.
New Date & Time
01/01/2001 12:0X
New Date & Time
01/01/2001 12:X0
New Date & Time
X1/01/2001 12:00
Retrieve and view the time
by pressing the C key.
Save the time by
pressing the A key.
Press the END key to exit back to the main menu.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
22
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Alarm Delay
The Alarm Delay menu is used to set the properties of the “Tamper Alarm” and “Button Stuck”
features that are built into the JACQUES RS485 Slaves. See FIGURE 21 below for changing the
Alarm Delay properties.
Note: These Alarm features are only found with the JACQUES RS485 Slaves.
• The Tamper Alarm feature is used to alert the Operator on the Master display screen, that a
Slave has been pulled out of its mounting.
• The Button Stuck feature is used to alert the Operator on the Master display screen, that a
Slave has a jammed Call button pushed in.
FIGURE 21: The Alarm Delay menu selects the Tamper and Button Stuck Alarm options.
Use the UP DOWN keys to select the Alarm Delay menu option.
Press ENTER to begin.
Alarm Delay
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Use the UP, DOWN keys to
select the different options.
Disable Alarm
These Delay settings determine the
amount of time that passes on a valid
Alarm message to be resent to the
Master, IF the Alarm is not cleared.
EG:
- Slave produces an Alarm.
- Slave sends Alarm message to
Master
- Master displays Alarm
- Operator clears Alarm on Master
- x minutes later, the Alarm message
will reappear at the Master, IF the
Alarm is not cleared at the Slave.
The Disable Alarm
setting is used to completely
disable the Alarm function.
(The Master will not display
any Alarm messages at all).
20min. Delay
10min.Delay
2min.Delay
Press the ENTER key
to save the setting and
return to the Alarm
Delay screen.
No Delay
The No Delay setting will allow predetermined Delay times on
Alarm messages sent from the Slaves.
Button Stuck = every 2 minutes, Tamper = every 20 seconds
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
23
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Audio Mode
The Audio Mode menu is used to set the HandsFree properties of the Master’s microphone.
The microphone used for the Operator to talk to the Caller during an Intercom call or PA
announcement, is located inside the DCS-550M Master, at the bottom Right-Hand corner of the front
panel.
This microphone can be set in one of two modes. See FIGURE 23 below for changing the options.
HandsFree Off:
The Operator needs to press a Push-To- Talk key (ENTER key), located on the front panel of the
DCS-550M Master, to enable the microphone when a call is connected.
HandsFree On:
The Operator doesn’t need to press a key to enable the microphone – it is always active, when a call is
connected.
FIGURE 23: The Audio Mode menu enables the Push-To-Talk microphone function
Use the UP DOWN keys to select the Audio Mode menu option.
Press ENTER to begin.
Audio Mode
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Use the UP, DOWN keys to
select the different options.
HandsFree Off
HandsFree On
Press the ENTER key
to save the setting and
return to the Audio
Mode screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
24
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Relay Settings
The DCS-550M Master can switch up to two individual Relays, which are located on the Slave
Stations, during a Call connect. These Relays are used to activate external devices, such as Boom
Gates and Door Locks, during a Call connection. See FIGURE 22 below for changing the Alarm
Delay properties.
FIGURE 22: The Relay Settings menu selects the Slave Station relay switching options.
Press the END
key to return to
the System
Idle screen.
Use the UP DOWN keys to select the Relay Settings menu option.
Press ENTER to begin.
Press the ENTER
key to Save settings.
Relay Settings
01/01/2000 12:00
Use the ASTERISK key to toggle between
Enabled or Disabled.
Press the ENTER key to
change settings
Relay x Disabled
ON time = 1.0s
Relay 1 Enabled
ON time = 1.0s
Relay x Enabled
ON time = 1.0s
Use the UP / DOWN keys to select
Relay 1 / Relay 2 options:
End Call
Use the NUMBER keys
to enter in the desired
Relay ON time (in 0.1
second units, ignoring the
decimal point).
Relay x Enabled
End Call = No
EG: Keying in 5 and 6
will change the Relay ON
time to 5.6 seconds.
Press the ENTER key to Save settings.
Use the ASTERISK key to toggle
between Yes or No.
Relay 1 Enabled
End Call = Yes
Use the UP / DOWN keys to select
Relay 1 / Relay 2 options:
Enabled/Disabled
ON time.
Relay 1 Enabled
End Call = No
Relay 2 Disabled
End Call function (if enabled) will automatically
energise the Relay and then end the call after xx seconds
Default setting = No
Note: If a relay is Disabled, then End Call will not be displayed along the bottom row of the display
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
25
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Get Tags?
In a finished Intercom System, the Master needs to find and validate all of the connected Devices,
Tags and Class ID. This process needs doing only the once and then every time a new Device is added
to the Intercom System.
The following FIGURE 24 shows how the DCS-550M Master finds the attached Devices. When it
finds a Device, it then records its individual Tag, Descriptor and Class ID and stores this information
into its own internal Flash ROM.
This provides a database of all the Devices and Tags found within the Intercom System.
FIGURE 24: The following Get Tags procedure needs to be done when the Intercom System is first
commissioned and then every time a new Device is added to the Intercom System.
Use the UP DOWN keys to select the Get Tags menu option.
Press ENTER to begin.
Press the END key to
return to the System
Idle screen.
Get Tags ?
(1=Yes, *=No)
Press the 1 key to Get the Tags.
Press the * key to Abort and Exit.
The Master begins to search all of the Tags
and Descriptors in the Intercom System
Requesting Tags
xx Tag(s) Found
Save Tags ?
(1=Yes, *=No)
x Tags Saved
Any key to exit
Req Descriptors
Press the 1 key to Save the Tags.
Press the * key to Abort and Exit.
All of the Devices Tags, Descriptors and Class ID’s
have now been saved into the Flash ROM, located
inside the Master.
Press any key to Exit.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
26
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Isolate Slave
The Isolate Slave menu (FIGURE 25) is used to allow the operator to disable or isolate selected
Slaves within an intercom system. When a Slave is isolated, it is effectively disabled from the system,
until it is re-enabled from this same menu (see next page).
A Slave may need to be isolated if for example, a Cell or room is empty, or if the Slave is faulty or
damaged.
FIGURE 25: Isolate Slave menu option.
Use the UP DOWN keys to select the Isolate Slave menu option.
Press ENTER to begin.
Isolate Slave
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
In order to isolate a particular
Slave, that Slave’s Tag number
must be entered at the Isolate
menu, followed by the ENTER
key.
Any number of Tags can be
entered here.
Isolate
Example: Isolate Tag# 3
Example: Isolate Tag# 131
Press the END key to
return to the Isolate
Slave screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
27
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Isolate Slave (continued)
Scrolling through the Isolated Slaves
If ISO is displayed on the top right-hand side of the System Idle screen (FIGURE 26), it indicates
that there are one or more Slaves already isolated.
To quickly view these isolated Slaves, go to the Isolate Slave menu and then press the ENTER
key. Scroll through the isolated Slaves by using the UP and DOWN keys.
FIGURE 26: ISO is displayed on the top right of the System Idle screen.
ISO.
Use the UP DOWN keys to select the Isolate Slave menu option.
Press ENTER to begin.
Isolate Slave
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Isolate
Example:
Scroll to 2nd Isolated Slave, Tag# 3
Cell 1
2:3 Slave
Press the END key to
return to the Isolate
Slave screen.
L1 EXIT
1:131 Slave
Use the UP DOWN keys
to scroll through the Isolated Slaves
Example:
Scroll to 1st Isolated Slave, Tag# 131
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
28
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Isolate Slave (continued)
De-Isolate Slaves
If ISO is displayed on the top right-hand side of the System Idle screen (FIGURE 27), it indicates
that there are one or more Slaves already isolated. At some time, those Slaves will need to be deisolated to bring them back online into the intercom system.
To De-Isolate these Slaves, use the same procedure as the Isolate Slave function, except that the
Slave’s Tag number must be followed by a “D” key, instead of “ENTER”.
FIGURE 27: De-Isolate Slave menu option.
ISO.
Use the UP DOWN keys to select the Isolate Slave menu option.
Press ENTER to begin.
Isolate Slave
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
In order to De-Isolate a
particular Slave, that Slave’s
Tag number must be entered
at the Isolate menu,
followed by the D key.
Isolate
Any number of Tags can be
entered here.
Example: De-Isolate Tag# 3
Example: De-Isolate Tag# 131
Press the END key to
return to the Isolate
Slave screen.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
29
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Aux Channel Set
The Aux Channel Set menu (FIGURE 28) is used to allow the operator to change the auxiliary
audio channel number and volume level, for any connected Slaves, directly from the Master.
About Auxiliary audio channels:
There are two auxiliary audio channels present within the Jacques Intercom system. Usually one
channel will be connected to a radio tuner and the other to another audio source such as a CD player.
These two audio channels can each be individually activated and controlled via the Aux Channel Set
menu.
The audio from the Aux audio channels are heard through the individual Slaves speakers. The Aux
Channel Set menu is used to set the audio channels and individual volume levels.
It is noted here that even once these levels are set from the Master, the Slave can still override these
settings if that Slave has separate Volume and Aux select buttons.
FIGURE 28: Aux Channel Set menu option.
Use the UP DOWN keys to select the Aux Channel Set menu option.
Press ENTER to begin.
Aux Channel Set
01/01/2001 12:00
Press the END key to return to
the System Idle screen.
Slave?
Select the Slave to be changed by either one of two ways:
Key in the correct Tag number of the Slave (eg: 5678) and then press the ANSWER key.
Scroll through the tag list by using the UP and DOWN keys and then press the ANSWER key.
The display changes to:
Slave: 5678
Ch=1 Vol=5
…continued next page:
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
30
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
SECTION 2 – Menu Operations
Aux Channel Set (continued)
Slave: 5678
Ch=1 Vol=5
Slave: 5678 is the selected Slave’s Tag number.
Ch=1 is the current channel selection value. Channels can have one of four values, they are:
• “OFF” - There are no auxiliary audio channels selected. When this is set, the volume
selection disappears from the screen.
• “1” – Auxiliary audio channel number 1 has been selected.
• “2” - Auxiliary audio channel number 2 has been selected.
• “3” – This is reserved for future use.
Vol=5 is the current volume level value. Volume levels can have one of eight values, they are:
• “0” – no volume or speaker mute.
• “1”, “2”, “3”, “4”, “5”, “6”, “7” – Slave speaker volume levels. Level 1 is the softest level,
Level 7 is the loudest level.
To change the settings:
The Ch=? and Vol=? Values can be changed in this screen.
•
•
•
Use the star “*” key to toggle between these two values.
Use the UP and DOWN keys to change the values.
Once the values have been correctly entered, press the ANSWER key to save these changes.
The display will show your new values for 3 seconds, before it goes back into Slave selection screen:
Slave selection screen:
Slave?
The top line displays the tag number of the Slave last used. You can either press the ANSWER key to
edit the same Slave (in case you made a mistake before), or enter a new Tag number as before.
Tag numbers can be in the range from 1 to 8191.
If you enter number “9999”, the selected channel number and volume level will apply to all local
intercoms.
To exit and save all changes, press the END key.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
31
Jacques Electronics Pty Ltd
TECHNICAL MANUAL - JACQUES DCS-550M SERIES 2 MASTER
For further details about JACQUES Intercom features and designs,
please visit the JACQUES website at: www.jacques.com.au
 copyright 2002 JACQUES ELECTRONICS Pty Ltd
Jacques Electronics Pty Ltd reserves the right to continually improve products by updating any
equipment specifications, document context and design styling and then passing this information onto
this document.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Email: [email protected]
268 Montague Road, West End
Queensland, Brisbane, Australia 4101
Web: http://www.jacques.com.au
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement