Chicago Electric | MIG 180 | Owner`s manual | Chicago Electric MIG 180 Owner`s manual

OM-925
217 694B
August 2004
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
Description
Arc Welding Power Source And
Wire Feeder
R
Handler 140 / 180
And H-10 Gun
Visit our website at
www.HobartWelders.com
From Hobart to You
Thank you and congratulations on choosing Hobart. Now you can get the
job done and get it done right. We know you don’t have time to do it any
other way.
This Owner’s Manual is designed to help you get the most out of your
Hobart products. Please take time to read the Safety precautions. They
will help you protect yourself against potential hazards on the worksite.
We’ve made installation and operation quick
and easy. With Hobart you can count on years
of reliable service with proper maintenance.
And if for some reason the unit needs repair,
there’s a Troubleshooting section that will help
you figure out what the problem is. The parts
list will then help you to decide the exact part
Hobart is registered to the
you may need to fix the problem. Warranty and
ISO 9001:2000 Quality
service information for your particular model
System Standard.
are also provided.
Hobart Welders manufactures a full line
of welders and welding related equipment.
For information on other quality Hobart products, contact your local Hobart
distributor to receive the latest full line catalog or individual catalog sheets.
To locate your nearest distributor or service agency call 1-877-Hobart1.
Hob_Thank 7/03
Working as hard as you
do − every power source
from Hobart is backed by
the best warranty in the
business.
TABLE OF CONTENTS
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien de l’appareil. . . . . . . . . . . .
2-4. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Information sur les champs électromagnétiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 − DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 − SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 − INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Installing Welding Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Installing Work Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Process/Polarity Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4. Changing Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-5. Installing Gas Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-6. Selecting A Location And Connecting Input Power For 115 VAC Model . . . . . . . . . . . . . . . . . . . . . . . . .
5-7. Selecting A Location And Connecting Input Power For 230 VAC Model . . . . . . . . . . . . . . . . . . . . . . . .
5-8. Electrical Service Guide For 230 VAC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-9. Installing Wire Spool And Adjusting Hub Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-10. Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 − OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. Weld Parameter Chart For 115 VAC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Weld Parameter Chart For 230 VAC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 − MAINTENANCE &TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. Drive Motor Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4. Changing Drive Roll Or Wire Inlet Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5. Replacing Gun Contact Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-6. Cleaning Or Replacing Gun Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7. Replacing Switch And/Or Head Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-8. Troubleshooting Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8 − ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
3
3
4
4
5
5
5
7
8
8
9
9
9
9
10
11
12
12
12
13
13
14
15
16
17
17
18
19
19
20
22
24
24
24
24
25
25
26
27
28
29
TABLE OF CONTENTS
SECTION 9 − MIG WELDING (GMAW) GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-1. Typical MIG Process Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-2. Typical MIG Process Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-3. Holding And Positioning Welding Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-4. Conditions That Affect Weld Bead Shape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-5. Gun Movement During Welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-6. Poor Weld Bead Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-7. Good Weld Bead Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-8. Troubleshooting − Excessive Spatter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-9. Troubleshooting − Porosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-10. Troubleshooting − Excessive Penetration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-11. Troubleshooting − Lack Of Penetration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-12. Troubleshooting − Incomplete Fusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-13. Troubleshooting − Burn-Through . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-14. Troubleshooting − Waviness Of Bead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-15. Troubleshooting − Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-16. Common MIG Shielding Gases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-17. Troubleshooting Guide For Semiautomatic Welding Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 − PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARRANTY
31
31
32
33
34
35
35
35
36
36
36
37
37
37
38
38
39
39
42
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING
som _8/03
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Y Marks a special safety message.
. Means “Note”; not safety related.
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
1-2. Arc Welding Hazards
Y The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-5. Read and follow all
Safety Standards.
D If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Y Only qualified persons should install, operate, maintain, and
repair this unit.
D Wear a safety harness if working above floor level.
D Keep all panels and covers securely in place.
Y During operation, keep everybody, especially children, away.
D Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
D Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists after removal of
input power on inverters.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D Keep your head out of the fumes. Do not breathe the fumes.
D Always verify the supply ground − check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first − double-check connections.
D Frequently inspect input power cord for damage or bare wiring −
replace cord immediately if damaged − bare wiring can kill.
D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or poorly spliced cables.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not drape cables over your body.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D If inside, ventilate the area and/or use exhaust at the arc to remove
welding fumes and gases.
D If ventilation is poor, use an approved air-supplied respirator.
D Read the Material Safety Data Sheets (MSDSs) and the
manufacturer’s instructions for metals, consumables, coatings,
cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and if necessary, while wearing an
air-supplied respirator. The coatings and any metals containing
these elements can give off toxic fumes if welded.
OM-925 Page 1
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear a welding helmet fitted with a proper shade of filter to protect
your face and eyes when welding or watching (see ANSI Z49.1
and Z87.1 listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash and
glare; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant material (leather and wool) and foot protection.
BUILDUP OF GAS can injure or kill.
D Shut off shielding gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
HOT PARTS can cause severe burns.
D Do not touch hot parts bare handed.
D Allow cooling period before working on gun or
torch.
MAGNETIC FIELDS can affect pacemakers.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Protect yourself and others from flying sparks and hot metal.
D Do not weld where flying sparks can strike flammable material.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.
D Do not use welder to thaw frozen pipes.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
FLYING METAL can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
OM-925 Page 2
D Pacemaker wearers keep away.
D Wearers should consult their doctor before
going near arc welding, gouging, or spot
welding operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder − explosion will result.
D Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and CGA publication P-1 listed in Safety
Standards.
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
MOVING PARTS can cause injury.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
FALLING UNIT can cause injury.
H.F. RADIATION can cause interference.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are
long enough to extend beyond opposite side of
unit.
D
OVERUSE can cause OVERHEATING
D
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
D
D
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
ARC WELDING can cause interference.
MOVING PARTS can cause injury.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D
D
WELDING WIRE can cause injury.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-4. California Proposition 65 Warnings
Y Welding or cutting equipment produces fumes or gases which
contain chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California Health &
Safety Code Section 25249.5 et seq.)
For Gasoline Engines:
Y Engine exhaust contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive
harm.
Y Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
For Diesel Engines:
Y Diesel engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects, and
other reproductive harm.
OM-925 Page 3
1-5. Principal Safety Standards
Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,
from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
(phone: 305-443-9353, website: www.aws.org).
Boulevard, Rexdale, Ontario, Canada M9W 1R3 (phone:
800−463−6727 or in Toronto 416−747−4044, website: www.csa−international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126 (phone: 305-443-9353, website: www.aws.org).
Practice For Occupational And Educational Eye And Face Protection,
ANSI Standard Z87.1, from American National Standards Institute, 11
West 42nd Street, New York, NY 10036−8002 (phone: 212−642−4900,
website: www.ansi.org).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269−9101 (phone: 617−770−3000, website: www.nfpa.org and www.
sparky.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (phone:
617−770−3000,website: www.nfpa.org and www. sparky.org).
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202−4102 (phone: 703−412−0900, website: www.cganet.com).
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there
are 10 Regional Offices−−phone for Region 5, Chicago, is
312−353−2220,website: www.osha.gov).
1-6. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
To reduce magnetic fields in the workplace, use the following
procedures:
OM-925 Page 4
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
About Pacemakers:
Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.
SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANT
UTILISATION
som_fre 8/03
2-1. Signification des symboles
Signifie « Mise en garde. Faire preuve de vigilance. »
Cette procédure présente des risques identifiés par les
symboles adjacents aux directives.
Y Identifie un message de sécurité particulier.
. Signifie « NOTA » ; n’est pas relatif à la sécurité.
Ce groupe de symboles signifie « Mise en garde. Faire preuve de vigilance. » Il y a des dangers liés aux CHOCS ÉLECTRIQUES, aux
PIÈCES EN MOUVEMENT et aux PIÈCES CHAUDES. Se reporter
aux symboles et aux directives ci-dessous afin de connaître les mesures à prendre pour éviter tout danger.
2-2. Dangers relatifs au soudage à l’arc
Y Les symboles ci-après sont utilisés tout au long du présent
manuel pour attirer l’attention sur les dangers potentiels et les
identifier. Lorsqu’on voit un symbole, faire preuve de vigilance et
suivre les directives mentionnées afin d’éviter tout danger. Les
consignes de sécurité énoncées ci-après ne font que résumer le
contenu des normes de sécurité mentionnées à la section 2-4.
Lire et respecter toutes ces normes.
Y L’installation, l’utilisation, l’entretien et les réparations ne doivent être confiés qu’à des personnes qualifiées.
Y Pendant l’utilisation de l’appareil, tenir à l’écart toute personne,
en particulier les enfants.
LES DÉCHARGES ÉLECTRIQUES
peuvent être mortelles.
Un simple contact avec des pièces sous tension peut
causer une électrocution ou des blessures graves.
L’électrode et le circuit de soudage sont sous tension
dès que l’appareil est en fonctionnement. Le circuit
d’entrée et les circuits internes de l’appareil sont également sous tension.
En soudage semi−automatique ou automatique, le fil, le dévidoir, le
logement des galets d’entraînement et les pièces métalliques en contact
avec le fil de soudage sont sous tension. Tout matériel mal installé ou mal
mis à la terre présente un danger.
D Ne jamais toucher aux pièces électriques sous tension.
D Porter des gants et des vêtements de protection secs et exempts de
trous.
D S’isoler de la pièce et de la terre au moyen de tapis ou autres dispositifs isolants suffisamment grands pour empêcher tout contact
physique avec la pièce ou la terre.
D
D
D
Ne pas se servir d’une source de courant alternatif dans les zones humides, les endroits confinés ou là où on risque de tomber.
Ne se servir d’une source de courant alternatif QUE si le procédé de soudage l’exige.
Si l’utilisation d’une source de courant alternatif s’avère nécessaire, se servir de la fonction de télécommande si l’appareil en est équipé.
D Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation, à la réparation ou à l’entretien de l’appareil. Couper/étiqueter
l’alimentation selon la norme OSHA 29 CFR 1910.147 (voir les normes de sécurité).
D Installer et mettre à la terre correctement l’appareil conformément à
son manuel d’utilisation et aux codes nationaux, provinciaux et
municipaux.
D Toujours vérifier la terre du cordon d’alimentation − Vérifier et s’assurer que le fil de terre du cordon d’alimentation est bien raccordé à la
borne de terre du sectionneur ou que la fiche du cordon est raccordée
à une prise correctement mise à la terre.
D Pour exécuter les branchements d’entrée, fixer d’abord le conducteur
de mise à la terre adéquat et contre−vérifier les connexions.
D Vérifier fréquemment le cordon d’alimentation et s’assurer qu’il n’est
ni endommagé ni dénudé ; le remplacer immédiatement s’il est endommagé − tout câble dénudé peut causer une électrocution.
D Mettre l’appareil hors tension quand on ne l’utilise pas.
D Ne pas utiliser de câbles usés, endommagés, de calibre insuffisant ou
mal épissés.
D Ne pas s’enrouler les câbles autour du corps.
D Si la pièce soudée doit être mise à la terre, le faire directement avec un
câble distinct.
D Ne pas toucher l’électrode quand on est en contact avec la pièce, la
terre ou une électrode d’une autre machine.
D N’utiliser que du matériel en bon état. Réparer ou remplacer sur−le−
champ les pièces endommagées. Entretenir l’appareil conformément
au présent manuel.
D Porter un harnais de sécurité quand on travaille en hauteur.
D Maintenir solidement en place tous les panneaux et capots.
D Fixer le câble de retour de façon à obtenir un bon contact métal sur
métal avec la pièce à souder ou la table de travail, le plus près possible
de la soudure.
D
Ne pas connecter plus d’une électrode ou plus d’un câble de masse à un
même terminal de sortie.
Il subsiste un COURANT CONTINU IMPORTANT
dans les convertisseurs après la suppression de
l’alimentation électrique.
D Arrêter les convertisseurs, débrancher le courant électrique et décharger les condensateurs d’alimentation selon les instructions
énoncées à la section Entretien avant de toucher les pièces.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Le soudage génère des fumées et des gaz dont
l’inhalation peut être dangereuse pour la santé.
D Se tenir à distance des fumées et ne pas les inhaler.
D À l’intérieur, ventiler la zone et/ou utiliser un dispositif d’aspiration au
niveau de l’arc pour l’évacuation des fumées et des gaz de soudage.
D Si la ventilation est insuffisante, utiliser un respirateur à adduction
d’air agréé.
D Lire les fiches techniques de santé−sécurité (FTSS) et les instructions du fabricant concernant les métaux, les consommables, les
revêtements, les nettoyants et les dégraisseurs.
D Ne travailler dans un espace clos que s’il est bien ventilé ou porter un
respirateur à adduction d’air. Demander toujours à un surveillant dûment formé de se tenir à proximité. Des fumées et des gaz de soudage
peuvent se substituer à l’air, abaisser la teneur en oxygène et causer
des lésions ou des accidents mortels. S’assurer que l’air est respirable.
D Ne pas souder à proximité d’opérations de dégraissage, de nettoyage
ou de pulvérisation. La chaleur et les rayons de l’arc peuvent réagir en
présence de vapeurs et former des gaz hautement toxiques et irritants.
D Ne pas souder de métaux munis d’un revêtement, tels que la tôle
d’acier galvanisée, plombée ou cadmiée, à moins que le revêtement
n’ait été enlevé dans la zone de soudage, que l’endroit soit bien ventilé, et si nécessaire, porter un respirateur à adduction d’air. Les
revêtements et tous les métaux renfermant ces éléments peuvent dégager des fumées toxiques lorsqu’on les soude.
OM-925 Page 5
LES RAYONS DE L’ARC peuvent causer des brûlures oculaires et cutanées.
Le rayonnement de l’arc génère des rayons visibles et
invisibles intenses (ultraviolets et infrarouges) susceptibles de causer des brûlures oculaires et cutanées.
Des étincelles sont projetées pendant le soudage.
D Porter un masque de soudage muni d’un filtre de la nuance adéquate
pour se protéger le visage et les yeux pendant le soudage ou pour regarder (voir les normes de sécurité ANSI Z49.1 et Z87.1).
D Porter des lunettes de sécurité à écrans latéraux sous le masque.
D Utiliser des écrans ou des barrières pour protéger les tiers de l’éclat
éblouissant ou aveuglant de l’arc ; leur demander de ne pas regarder
l’arc.
D Porter des vêtements de protection en matière durable et ignifuge
(cuir ou laine) et des chaussures de sécurité.
LE SOUDAGE peut causer un incendie ou une explosion.
Le soudage effectué sur des récipients fermés tels que
des réservoirs, des fûts ou des conduites peut causer
leur éclatement. Des étincelles peuvent être projetées
de l’arc de soudure. La projection d’étincelles, les
pièces chaudes et les équipements chauds peuvent causer des
incendies et des brûlures. Le contact accidentel de l’électrode avec tout
objet métallique peut causer des étincelles, une explosion, un surchauffement ou un incendie. Avant de commencer le soudage, vérifier et
s’assurer que l’endroit ne présente pas de danger.
D Se protéger et protéger les tiers de la projection d’étincelles et de métal chaud.
D Ne pas souder à un endroit où des étincelles peuvent tomber sur des
substances inflammables.
D Placer toutes les substances inflammables à une distance de 10,7 m
de l’arc de soudage. En cas d’impossibilité, les recouvrir soigneusement avec des protections agréées.
D Des étincelles et des matières en fusion peuvent facilement passer
même par des fissures et des ouvertures de petites dimensions.
D Surveiller tout déclenchement d’incendie et tenir un extincteur à proximité.
D Le soudage effectué sur un plafond, un plancher, une paroi ou une
cloison peut déclencher un incendie de l’autre côté.
D Ne pas souder des récipients fermés tels que des réservoirs, des fûts
ou des conduites, à moins qu’ils n’aient été préparés conformément à
l’AWS F4.1 (voir les normes de sécurité).
D Brancher le câble sur la pièce le plus près possible de la zone de soudage pour éviter que le courant ne circule sur une longue distance, par
des chemins inconnus, et ne cause des risques d’électrocution et d’incendie.
D Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
D En cas de non utilisation, enlever la baguette d’électrode du porte−
électrode ou couper le fil au raz du tube−contact.
D Porter des vêtements de protection exempts d’huile tels que des
gants en cuir, une chemise en tissu épais, des pantalons sans revers,
des chaussures montantes et un masque.
D Avant de souder, retirer tout produit combustible de ses poches, tel
qu’un briquet au butane ou des allumettes.
LES PARTICULES PROJETÉES peuvent blesser les yeux.
D Le soudage, le burinage, le passage de la pièce à
la brosse métallique et le meulage provoquent
l’émission d’étincelles et de particules métalliques. Pendant leur refroidissement, les soudures risquent de projeter du
laitier.
D
Porter des lunettes de sécurité à écrans latéraux agréés, même sous le
masque de soudage.
OM-925 Page 6
LES ACCUMULATIONS DE GAZ peuvent causer des blessures ou même
la mort.
Couper l’alimentation en gaz protecteur en cas de
non utilisation.
Veiller toujours à bien ventiler les espaces confinés ou porter un respirateur à adduction d’air agréé.
D
D
LES PIÈCES CHAUDES peuvent causer des brûlures graves.
D Ne pas toucher les pièces chaudes à main nue.
D Prévoir une période de refroidissement avant
d’utiliser le pistolet ou la torche.
LES CHAMPS MAGNÉTIQUES peuvent
perturber le fonctionnement des stimulateurs cardiaques.
D
D
Les personnes qui portent un stimulateur cardiaque
doivent se tenir à distance.
Ils doivent consulter leur médecin avant de s’approcher d’un lieu où on exécute des opérations de soudage à l’arc, de gougeage ou de soudage par points.
LE BRUIT peut affecter l’ouïe.
Le bruit de certains processus et équipements peut
affecter l’ouïe.
D
Porter des protecteurs d’oreille agréés si le niveau
sonore est trop élevé.
Les BOUTEILLES
peuvent exploser.
endommagées
Les bouteilles de gaz protecteur contiennent du gaz
sous haute pression. Toute bouteille endommagée
peut exploser. Comme les bouteilles de gaz font
normalement partie du procédé de soudage, les
manipuler avec précaution.
D Protéger les bouteilles de gaz comprimé de la chaleur excessive, des
chocs mécaniques, du laitier, des flammes nues, des étincelles et des
arcs.
D Placer les bouteilles debout en les fixant dans un support stationnaire
ou dans un porte−bouteilles pour les empêcher de tomber ou de se
renverser.
D Tenir les bouteilles éloignées des circuits de soudage ou autres circuits électriques.
D Ne jamais poser une torche de soudage sur une bouteille de gaz.
D Ne jamais mettre une électrode de soudage en contact avec une bouteille de gaz.
D Ne jamais souder une bouteille contenant du gaz sous pression − elle
risquerait d’exploser.
D N’utiliser que les bouteilles de gaz protecteur, régulateurs, tuyaux et
raccords adéquats pour l’application envisagée ; les maintenir en bon
état, ainsi que les pièces connexes.
D Détourner la tête lorsqu’on ouvre la soupape d’une bouteille.
D Laisser le capuchon protecteur sur la soupape, sauf en cas d’utilisation ou de branchement de la bouteille
D Lire et suivre les instructions concernant les bouteilles de gaz comprimé, les équipements associés et les publications P−1 de la CGA,
mentionnées dans les normes de sécurité.
2-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien de
l’appareil.
Risque D’INCENDIE OU D’EXPLOSION
LES ORGANES MOBILES peuvent
causer des blessures.
D Ne pas placer l’appareil sur une surface inflammable, ni au−dessus ou à proximité d’elle.
D Se tenir à l’écart des organes mobiles comme les
ventilateurs.
D Maintenir fermés et bien fixés les portes,
panneaux, recouvrements et dispositifs de
protection.
D Ne pas installer l’appareil à proximité de produits inflammables.
D Ne pas surcharger l’installation électrique − s’assurer que l’alimentation est correctement dimensionnée et protégée avant de mettre
l’appareil en service.
LA CHUTE DE L’APPAREIL peut
blesser.
D N’utiliser que l’anneau de levage pour lever l’appareil. NE PAS utiliser le chariot, les bouteilles de
gaz ou tout autre accessoire.
D Utiliser un engin de capacité adéquate pour lever
l’appareil.
D Si on utilise un chariot élévateur pour déplacer l’unité, s’assurer que
les fourches sont suffisamment longues pour dépasser du côté opposé de l’appareil.
L’EMPLOI EXCESSIF peut FAIRE
SURCHAUFFER L’ÉQUIPEMENT.
D Prévoir une période de refroidissement ; respecter le cycle opératoire nominal.
D Réduire le courant ou le cycle opératoire avant de
reprendre le soudage.
D Ne pas obstruer les orifices ou filtrer l’alimentation en air du poste.
LES CHARGES ÉLECTROSTATIQUES peuvent endommager les circuits imprimés.
D Mettre un bracelet antistatique AVANT de manipuler des cartes ou des pièces.
D Utiliser des pochettes et des boîtes antistatiques
pour stocker, déplacer ou expédier des cartes de
circuits imprimés.
LES PIÈCES MOBILES peuvent causer des blessures.
D Se tenir à l’écart des pièces mobiles.
D Se tenir à l’écart des points de coincement tels
que les dévidoirs.
LES FILS DE SOUDAGE peuvent causer des blessures.
D Ne pas appuyer sur la gâchette avant d’en avoir
reçu l’instruction.
D Ne pas diriger le pistolet vers soi, vers d’autres
personnes ou vers toute pièce mécanique en engageant le fil de soudage.
LE RAYONNEMENT HAUTE FRÉQUENCE (H. F.) risque de causer des
interférences.
D Le rayonnement haute fréquence peut causer
des interférences avec les équipements de radionavigation et de communication, les services de
sécurité et les ordinateurs.
D Ne demander qu’à des personnes qualifiées familiarisées avec les
équipements électroniques de faire fonctionner l’installation.
D L’utilisateur est tenu de faire corriger rapidement par un électricien
qualifié les interférences causées par l’installation.
D Si la Federal Communications Commission signale des interférences, arrêter immédiatement l’appareil.
D Faire régulièrement contrôler et entretenir l’installation.
D Maintenir soigneusement fermés les panneaux et les portes des sources de haute fréquence, maintenir le jeu d’éclatement au réglage
adéquat et utiliser une terre et un blindage pour réduire les interférences éventuelles.
LE SOUDAGE À L’ARC peut causer
des interférences.
D L’énergie électromagnétique peut causer des
interférences avec l’équipement électronique
sensible tel que les ordinateurs et l’équipement
commandé par ordinateur tel que les robots.
D Veiller à ce que tout l’équipement de la zone de soudage soit compatible au point de vue électromagnétique.
D Pour réduire la possibilité d’interférence, maintenir les câbles de soudage aussi courts que possible, les grouper, et les poser aussi bas
que possible (par ex. : à terre).
D Veiller à souder à une distance de 100 mètres de tout équipement
électronique sensible.
D Veiller à ce que le poste de soudage soit posé et mis à la terre conformément au présent manuel.
D En cas d’interférences après exécution des directives précédentes, il
incombe à l’utilisateur de prendre des mesures supplémentaires telles que le déplacement du poste, l’utilisation de câbles blindés,
l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone de
travail.
LES CHAMPS MAGNÉTIQUES peuvent
affecter les stimulateurs cardiaques.
D Porteurs de stimulateur cardiaque, restez à distance.
D Les porteurs d’un stimulateur cardiaque doivent
d’abord consulter leur médecin avant de s’approcher des opérations de soudage à l’arc, de gougeage ou de soudage par points.
OM-925 Page 7
2-4. Principales normes de sécurité
Safety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1,
de l’American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
(téléphone : (305) 443−9353, site Web : www.aws.org).
Rexdale, Rexdale (Ontario) Canada M9W 1R3 (téléphone : (800)
463−6727 ou à Toronto : (416) 747−4044, site Web : www.csa−international.org).
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, norme American Welding Society AWS
F4.1, de l’American Welding Society, 550 N.W. LeJeune Rd, Miami, FL
33126 (téléphone : (305) 443−9353, site Web : www.aws.org).
Practice For Occupational And Educational Eye And Face Protection,
norme ANSI Z87.1, de l’American National Standards Institute, 11 West
42nd Street, New York, NY 10036−8002 (téléphone : (212) 642−4900,
site Web : www.ansi.org).
National Electrical Code, norme NFPA 70, de la National Fire Protection
Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
02269−9101 (téléphone : (617) 770−3000, sites Web : www.nfpa.org et
www.sparky.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, norme NFPA 51B, de la National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269−9101 (téléphone : (617) 770−3000, site Web : www.nfpa.org et www.sparky.org).
Safe Handling of Compressed Gases in Cylinders, brochure CGA P−1,
de la Compressed Gas Association, 1735 Jefferson Davis Highway,
Suite 1004, Arlington, VA 22202−4102 (téléphone : (703) 412−0900,
site Web : www.cganet.com).
Code for Safety in Welding and Cutting, norme CSA W117.2, de la Canadian Standards Association, Standards Sales, 178 boulevard
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, de l’U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (il y a
10 bureaux régionaux − Téléphone pour la Région 5, Chicago : (312)
353−2220, site Web : www.osha.gov).
2-5. Information sur les champs électromagnétiques
Données sur le soudage électrique et les effets des champs magnétiques basse fréquence sur l’organisme
En parcourant les câbles de soudage, le courant crée des champs électromagnétiques. Les effets potentiels de tels champs restent
préoccupants. Cependant, après avoir examiné plus de 500 études qui
ont été faites pendant une période de recherche de 17 ans, un comité
de spécialistes du National Research Council a conclu : « L’accumulation de preuves n’a pas démontré que l’exposition aux champs
magnétiques et aux champs électriques à haute fréquence constitue un
risque pour la santé humaine ». Toutefois, les études et l’examen des
preuves se poursuivent. En attendant les conclusions finales de la recherche, il serait souhaitable de réduire l’exposition aux champs
électromagnétiques pendant le soudage ou le coupage.
OM-925 Page 8
Afin de réduire les champs électromagnétiques en milieu de travail, respecter les consignes suivantes :
1. Garder les câbles ensemble en les torsadant ou en les fixant avec du
ruban adhésif.
2. Mettre tous les câbles du côté opposé à l’opérateur.
3. Ne pas s’enrouler les câbles autour du corps.
4. Garder le poste de soudage et les câbles le plus loin possible de soi.
5. Placer la pince de masse le plus près possible de la zone de soudage.
Consignes relatives aux stimulateurs cardiaques :
Les personnes qui portent un stimulateur cardiaque doivent avant tout
consulter leur médecin. Si ce dernier les déclare aptes, il leur est recommandé de respecter les consignes ci-dessus.
SECTION 3 − DEFINITIONS
3-1. Symbols And Definitions
A
V
Amperage
Hz
Voltage
Hertz
Negative
Positive
Direct Current
(DC)
Single Phase
Input
Output
Voltage Input
Off
On
Do Not Switch
While Welding
Gas Metal Arc
Welding (GMAW)
Wire Feed
SECTION 4 − SPECIFICATIONS
4-1. Specifications
A. 115 VAC Model
Rated Welding
Output
90 A @ 19 Volts DC,
20% Duty Cycle
63 A @ 21 Volts DC,
20% Duty Cycle*
Wire Type
And Diameter
Amperage
Range
25 − 140
Maximum OpenCircuit Voltage
DC
Amperes Input at
Rated Load Output
115 V, 60 Hz, SinglePhase
KVA
KW
20
2.90
2.50
15*
2.20*
1.77*
28
Solid/
Stainless
Flux Cored
Aluminum
.023 − .035 in
(0.6 − 0.9 mm)
.030 − .035 in
(0.8 − 0.9 mm)
.030 in
(0.8 mm)
Amperage
Range
Maximum OpenCircuit Voltage
DC
Amperes Input at
Rated Load Output
230 V, 50/60 Hz,
Single-Phase
Weight
W/ Gun
57 lb
(26 kg)
Overall
Dimensions
Length: 19-1/2 in
(495 mm)
Width: 10-5/8 in
(270 mm)
Height: 12-3/8 in
(314 mm)
Wire Feed Speed Range
50 − 740 IPM (1.3 − 18.8 m/min) At No Load
40 − 700 IPM (1.0 − 17.8 m/min) Feeding Wire
* CSA Rating
B. 230 VAC Model
Rated Welding
Output
130 A @ 20 Volts
DC, 30% Duty Cycle
At 60 Hz Input − 20%
Duty Cycle At 50 Hz
Input
Wire Type
And Diameter
KVA
KW
Weight
W/ Gun
Overall
Dimensions
Length: 19-1/2 in
(495 mm)
25 − 180
30
20
4.60
3.75
68 lb
(31 kg)
Width: 10-5/8 in
(270 mm)
Height: 12-3/8 in
(314 mm)
Solid/
Stainless
Flux Cored
Aluminum
.023 − .035 in
(0.6 − 0.9 mm)
.030 − .045 in
(0.8 − 1.2 mm)
.030 − .035 in
(0.8 − 0.9 mm)
Wire Feed Speed Range
50 − 740 IPM (1.3 − 18.8 m/min) At No Load
40 − 700 IPM (1.0 − 17.8 m/min) Feeding Wire
OM-925 Page 9
4-2. Duty Cycle And Overheating
Duty Cycle is percentage of 10
minutes that unit can weld at rated
load without overheating.
If unit overheats, thermostat(s)
opens, output stops, and cooling
fan runs. Wait fifteen minutes for
unit to cool. Reduce amperage or
duty cycle before welding.
A. 115 VAC Model
200
Output Amperes
140
Y Exceeding duty cycle can
damage unit or gun and void
warranty.
100
80
60
40
20
10
1
2
4
6
8 10
40
20
60 80 100
Duty Cycle %
20% duty cycle at 90 amps
2 Minutes Welding
8 Minutes Resting
B. 230 VAC Model
Output Amperes
200
180
130
100
80
60
40
20
10
10
20
30
40
50
60 70 80
100
Duty Cycle %
30% duty cycle at 130 amps, 60 Hz
20% duty cycle at 130 amps, 50 Hz
3 Minutes Welding
7 Minutes Resting
Overheating
A or V
0
15
Minutes
OR
Reduce Duty Cycle
duty1 4/95 − 217 623-A / 217 757-A
OM-925 Page 10
4-3. Volt-Ampere Curves
The volt-ampere curves show the
minimum and maximum voltage
and amperage output capabilities of
the welding power source. Curves
of other settings fall between the
curves shown.
A. 115 VAC Model
30.0
25.0
20.0
Voltage
RANGE4
15.0
RANGE3
RANGE2
RANGE1
10.0
5.0
0.0
0
10
20
30
40
50
60
70
80 90 100 110
Amperage
120 130
140 150 160
B. 230 VAC Model
30.0
25.0
20.0
RANGE 4
Voltage
RANGE 3
15.0
RANGE 2
RANGE 1
10.0
5.0
0.0
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150 160 170 180 190 200 210 220
Amperage
ssb1.1 10/91 − 217 624-A / 217 758-A
OM-925 Page 11
SECTION 5 − INSTALLATION
5-1. Installing Welding Gun
1
2
3
4
Drive Assembly
Gun Securing Thumbscrew
Gun End
Loosen thumbscrew. Insert end
through opening until it bottoms
against drive assembly. Tighten
thumbscrew.
2
3
Welding gun must be inserted
completely to prevent leakage of
shielding gas.
4
Gun Trigger Leads
Insert leads, one at a time, through
gun opening on front panel.
Connect female friction terminals to
matching male terminals in unit.
Polarity is not important.
1
Close door.
803 711-A
5-2. Installing Work Clamp
1
2
3
4
2
Tools Needed:
1
3
3/8, 7/16 in
Slide one insulating sleeve over
work cable before connecting to
clamp.
4
5
6
5
6
Insulating Sleeves
Nut
Work Cable From Unit
Work Clamp
Screw
Work Clamp Tabs
Bend tabs around work cable.
Slide insulating
handles.
sleeves
over
802 456-A
OM-925 Page 12
5-3. Process/Polarity Table
Process
Cable Connections
Polarity
Cable To Gun
Cable To Work
GMAW − Solid wire with shielding gas
DCEP − Reverse polarity
Connect to positive (+) output terminal
Connect to negative (−) output
terminal
FCAW − Self-shielding wire −
no shielding gas
DCEN − Straight Polarity
Connect to negative (−)
output terminal
Connect to positive (+) output
terminal
5-4. Changing Polarity
1
CHANGING
POLARITY
2
DCEN
Electrode negative for
flux cored wire
Lead Connections For Direct
Current Electrode Negative
(DCEN)
Lead Connections For Direct
Current Electrode Positive
(DCEP)
Always read and follow wire
manufacturer’s
recommended
polarity, and see Section 5-3.
Close door.
1
DCEP
Electrode positive for
solid wire
2
Ref. 209 228 / Ref. 209 229
OM-925 Page 13
5-5. Installing Gas Supply
Obtain gas cylinder and chain to
running gear, wall, or other
stationary support so cylinder
cannot fall and break off valve.
. DO NOT use Argon/Mixed gas regulator/flowmeter
with CO2 shielding gas. See Parts List for optional
CO2 gas regulator/flowmeter.
1
4
2
7
3
5
1
Cap
2
Cylinder Valve
Remove cap, stand to side of valve,
and open valve slightly. Gas flow
blows dust and dirt from valve.
Close valve.
3
Cylinder
4
Regulator/Flowmeter
Install so face is vertical.
5
Regulator/Flowmeter Gas
Hose Connection
6
Welding Power Source Gas
Hose Connection
Connect supplied gas hose
between regulator/flowmeter gas
hose connection, and fitting on rear
of welding power source.
7
Argon Gas Or
Mixed Gas
6
Flow Adjust
Turn flow adjust screw to increase
or decrease gas flow. Flow rate
should be set when gas is flowing
through welding power source and
welding gun. Turn Range switch to
Purge or Fan Only position. Press
gun trigger to start gas flow. Typical
flow rate is 20 cfh (cubic feet per
hour). Check wire manufacturer’s
recommended flow rate.
Tools Needed:
5/8, 1-1/8 in
Ref. 802 028-A / 802 441
OM-925 Page 14
5-6. Selecting A Location And Connecting Input Power For 115 VAC Model
1
2
1
18 in
(460 mm)
Rating Label
Grounded Receptacle
A 115 volt, 20 ampere individual
branch circuit protected by
time-delay fuses or circuit breaker
is required.
2
3
3
Plug From Unit
Select extension cord of 14 AWG
for up to 50 ft (15 m) or 12 AWG for
50 up to 200 ft (61 m).
Y Special installation may be
required where gasoline or
volatile liquids are present −
see NEC Article 511 or CEC
Section 20.
18 in
(460 mm)
803 712-B
OM-925 Page 15
5-7. Selecting A Location And Connecting Input Power For 230 VAC Model
1
Rating Label
Supply correct input power.
2
3
Plug (NEMA 6-50P)
Receptacle (NEMA 6-50R)
Connect plug to receptacle.
4
18 in (457 mm) of
space for airflow
Line Disconnect Device
See Section 5-8.
4
Y Special installation may be
required where gasoline or
volatile liquids are present −
see NEC Article 511 or CEC
Section 20.
L1
Y Always connect
grounding
conductor first.
L2
= GND/PE
1
2
3
L1
L2
230 VAC, 1
Y Do not move or operate unit
where it could tip.
ssb2.2* 1/94 − 803 713-B
OM-925 Page 16
5-8. Electrical Service Guide For 230 VAC Model
Input Voltage
230
Input Amperes At Rated Output
20
Max Recommended Standard Fuse Or Circuit Breaker Rating In Amperes
Circuit Breaker 1, Time-Delay 2
25
Normal Operating 3
30
14
Min Input Conductor Size In AWG
67
(20)
Max Recommended Input Conductor Length In Feet (Meters)
14
Min Grounding Conductor Size In AWG
Reference: 1999 National Electrical Code (NEC)
1 Choose a circuit breaker with time-current curves comparable to a Time Delay Fuse.
2 “Time-Delay” fuses are UL class “RK5” .
3 “Normal Operating” (general purpose − no intentional delay) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and
above).
5-9. Installing Wire Spool And Adjusting Hub Tension
Installing 4 in (102 mm) Wire Spool
When a slight force is needed
to turn spool, tension is set.
Installing 8 in (203 mm) Wire Spool
Adapter used with
8 in (203 mm)
spool only.
When a slight force is needed
to turn spool, tension is set.
Retaining ring used
with 8 in (203 mm)
spool only.
Tools Needed:
1/2 in
803 012 / 803 013 -B / Ref. 802 971-C
OM-925 Page 17
5-10. Threading Welding Wire
1
2
3
4
5
6
4
Wire Spool
Welding Wire
Inlet Wire Guide
Pressure Adjustment Knob
Drive Roll
Gun Conduit Cable
Lay gun cable out straight.
6
Tools Needed:
1
2
3
5
. Hold wire tightly to keep it
from unraveling.
4 in
(102 mm)
6 in
(150 mm)
Open pressure assembly. Make sure
feed roll is set to correct groove to
match wire size (see Section 7-4).
Pull and hold wire; cut off end.
. Use pressure indicator
Tighten
scale to set a desired
drive roll pressure.
1
2
3
4
Be sure that wire is positioned
in proper feed roll groove.
Close and tighten pressure
assembly, and let go of wire.
Push wire thru guides into gun;
continue to hold wire.
Pressure
Indicator
Scale
Remove gun nozzle
and contact tip.
Turn power on. Be sure that Voltage range
switch is set to range 1, 2, 3, or 4 to feed wire.
Rotate knob until it “clicks” into detent. Wire
will not feed if range switch is set between
ranges or if set in the “PURGE” position.
Tighten
WOOD
Press gun trigger until wire comes
out of gun.
Be sure that tip matches wire diameter.
Reinstall contact tip and nozzle.
1
2
3
4
Feed wire to check drive roll pressure.
Tighten knob enough to prevent slipping.
Cut off wire. Close door.
Ref. 803 714-A
OM-925 Page 18
SECTION 6 − OPERATION
6-1. Controls
1
2
3
4
DO NOT SWITCH
WHILE WELDING
2
NE PAS CHANGER
DE PROCÉDÉ
PURGE
1
V
3
1
Wire Speed Control
Use control to select a wire feed speed. As
Voltage switch setting increases, wire
speed range also increases (see weld
setting label in welding power source or
Sections 6-2 or 6-3, as applicable).
2
Power Switch
4
3
Voltage Switch
The higher the selected number, the
thicker the material that can be welded
(see weld setting label in welding power
source or Sections 6-2 and 6-3, as
applicable). Do not switch under load.
Ref. 217 617-A
4
Voltage Switch - “Purge” Position
In purge position, fan runs but there is no
weld output or wire feed. Use “PURGE”
setting when adjusting gas flow at the
regulator.
. Switch must “click” into detent position
1, 2, 3, 4, or purge for proper contact.
OM-925 Page 19
6-2. Weld Parameter Chart For 115 VAC Model
OM-925 Page 20
217 618-A
OM-925 Page 21
6-3. Weld Parameter Chart For 230 VAC Model
OM-925 Page 22
217 754-B
OM-925 Page 23
SECTION 7 − MAINTENANCE &TROUBLESHOOTING
7-1. Routine Maintenance
Y Disconnect power before maintaining.
3 Months
Replace
unreadable
labels.
Repair or
replace
cracked
weld cable.
Clean and
tighten weld
terminals.
6 Months
Blow out or
vacuum inside.
During heavy
service, clean
monthly.
Or
7-2. Overload Protection
1
Circuit Breaker CB1
CB1 protects unit from overload. If
CB1 opens, unit shuts down.
1
Reset breaker.
802 441
7-3. Drive Motor Protection
Drive motor protection circuit protects drive motor from overload. If drive motor becomes inoperative, release gun
trigger and wait until protection circuit resets allowing drive motor to feed wire again.
OM-925 Page 24
7-4. Changing Drive Roll Or Wire Inlet Guide
1
2
Loosen screw. Slide tip as close to
drive rolls as possible without
touching. Tighten screw.
1
3
3
2
Tools Needed:
Inlet Wire Guide Securing
Screw
Inlet Wire Guide
.030/.035 Groove
Stamped .024
The drive roll consists of two different sized grooves. The stamped
markings on the end surface of the
drive roll refers to the groove on the
opposite side of the drive roll. The
groove closest to the motor shaft is
the proper groove to thread (see
Section 5-10).
4
4
Drive Roll
Retaining Pin
To secure drive roll, locate open slot
and push drive roll completely over
retaining pin, then rotate drive roll
(1/4 turn) to closed slot.
.023/.025 Groove
Stamped .030/.035
Ref. 803 714-A
7-5. Replacing Gun Contact Tip
Y Turn Off power before
replacing contact tip.
1
2
Nozzle
Contact Tip
Cut off welding wire at contact tip.
Remove nozzle.
Remove contact tip and install new
contact tip. Reinstall nozzle.
2
1
Tools Needed:
Ref. 802 399-A
OM-925 Page 25
7-6. Cleaning Or Replacing Gun Liner
Tools Needed:
Y Disconnect gun from unit.
8 mm / 10mm
Head Tube
Remove nozzle, contact tip,
adapter, gas diffuser, and wire
outlet guide.
8 mm
10 mm
Remove liner.
To Reassemble Gun:
Insert new liner.
Lay gun cable out straight
before installing new liner.
Blow out gun casing.
Install wire outlet guide so that 1/8
in (3 mm) of liner sticks out. Hand
tighten outlet guide, and then
tighten two full turns more.
Cut liner off so that 3/4 in (19 mm)
sticks out of head tube.
Install gas diffuser, adapter, contact
tip, and nozzle.
Ref. 802 446-A
OM-925 Page 26
7-7. Replacing Switch And/Or Head Tube
Y Turn Off welding power source
/wire feeder and disconnect gun.
1
Remove handle
locking nut.
3
2
Slide handle.
Remove switch housing. Install new switch and
connect leads (polarity is not important).
Reassemble in reverse order. If replacing head
tube, continue to end of figure.
4 Secure head
tube in vice.
5
6
Loosen jam nut.
Remove from vice
and turn head tube
out by hand.
Hand-tighten head tube into cable connector.
8
7
Place head tube in vice and tighten until
nuts are tight.
Remove from vice. Reposition handle and install
switch housing. Secure with handle locking nut.
Tools Needed:
19 mm
Ref. ST-800 795-C
OM-925 Page 27
7-8. Troubleshooting Table
Trouble
Remedy
No weld output; wire does not feed; fan Secure power cord plug in receptacle (see Section 5-6).
does not run
run.
Replace building line fuse or reset circuit breaker if open.
Place Power switch in On position (see Section 6-1).
Reset welding power source circuit breaker if open.
No weld output; wire does not feed; fan Thermostat TP1 open (overheating). Allow fan to run with gun trigger switch off; thermostat closes when
unit has cooled (see Section 4-2).
motor continues to run.
Check Voltage range switch position. Rotate knob until it “clicks” into detent at desired range setting.
Voltage range switch set in “PURGE” position. Set switch to position 1, 2, 3, or 4.
Secure gun trigger leads (see Section 5-1).
No weld output; wire feeds.
Connect work clamp to get good metal to metal contact.
Replace contact tip (see Section 7-5).
Check for proper polarity connections (see Section 5-4).
Check thumbscrew securing gun end to feed head adapter and tighten if necessary.
Low weld output.
Connect unit to proper input voltage or check for low line voltage.
Place voltage switch in desired position (see Section 6-1).
Electrode wire feeding stops during Straighten gun cable and/or replace damaged parts.
welding
welding.
Adjust drive roll pressure (see Section 5-10).
Change to proper drive roll groove (see Section 7-4).
Readjust hub tension (see Section 5-9).
Replace contact tip if blocked (see Section 7-5).
Clean or replace wire inlet guide or liner if dirty or plugged (see Section 7-4 or Section 7-6).
Replace drive roll or pressure bearing if worn or slipping (see Section 7-4).
Secure gun trigger leads or repair leads (see Section 5-1).
Check and clear any restrictions at drive assembly and liner (see Section 5-10 or Section 7-6).
Release gun trigger and allow gun and motor protection circuitry to reset.
Gun is not secured to feed head. Check thumbscrew securing gun end to feed head adapter and tighten
if necessary.
Have nearest Factory Authorized Service Agent check drive motor.
OM-925 Page 28
SECTION 8 − ELECTRICAL DIAGRAM
217 621-A
Figure 8-1. Circuit Diagram For 115 VAC Model
OM-925 Page 29
217 755-A
Figure 8-2. Circuit Diagram For 230 VAC Model
OM-925 Page 30
SECTION 9 − MIG WELDING (GMAW) GUIDELINES
9-1. Typical MIG Process Connections
Y Weld current can damage
electronic parts in vehicles.
Disconnect both battery
cables before welding on a
vehicle. Place work clamp as
close to the weld as possible.
Regulator/
Flowmeter
Wire Feeder/
Power Source
Shielding Gas
Gas Hose
Gun
Work Clamp
Workpiece
light mig 5/97 / Ref. 803 715-A
OM-925 Page 31
9-2.
Typical MIG Process Control Settings
NOTE
These settings are guidelines only. Material and wire type, joint design, fitup,
position, shielding gas, etc. affect settings. Test welds to be sure they comply to
specifications.
Material thickness determines weld
parameters.
1/8 or 0.125 in
Convert Material
Thickness to
Amperage (A)
(0.001 in = 1 ampere)
0.125 in = 125 A
.035 in
Wire
Size
Wire Size
Amperage Range
0.023 in
30 − 90 A
0.030 in
40 − 145 A
0.035 in
50 − 180 A
Recommendation
Wire Speed
(Approx.)
0.023 in
3.5 in per ampere
3.5 x 125 A = 437 ipm
0.030 in
2 in per ampere
2 x 125 A = 250 ipm
0.035 in
1.6 in per ampere
1.6 x 125 A = 200 ipm
Select Wire Size
Select Wire Speed
(Amperage)
125 A based on 1/8 in
material thickness
ipm = inches per minute
Low voltage: wire stubs into work
High voltage: arc is unstable (spatter)
Select Voltage
Set voltage midway between high/low voltage
Wire speed (amperage) controls weld
penetration (wire speed = burn-off rate)
Voltage controls height
and width of weld bead.
Ref. 803 710-A
OM-925 Page 32
9-3.
Holding And Positioning Welding Gun
NOTE
Welding wire is energized when gun trigger is pressed. Before lowering helmet and
pressing trigger, be sure wire is no more than 1/2 in (13 mm) past end of nozzle,
and tip of wire is positioned correctly on seam.
1
1
3
2
2
3
4
5
5
Hold Gun and Control Gun
Trigger
Workpiece
Work Clamp
Electrode Extension (Stickout)
1/4 to 1/2 in (6 To 13 mm)
Cradle Gun and Rest Hand on
Workpiece
4
0°-15°
90°
90°
End View of Work Angle
Side View of Gun Angle
GROOVE WELDS
0°-15°
45°
45°
End View of Work Angle
Side View of Gun Angle
FILLET WELDS
S-0421-A
OM-925 Page 33
9-4.
Conditions That Affect Weld Bead Shape
NOTE
Weld bead shape depends on gun angle, direction of travel, electrode extension
(stickout), travel speed, thickness of base metal, wire feed speed (weld current),
and voltage.
10°
Push
10°
Drag
Perpendicular
GUN ANGLES AND WELD BEAD PROFILES
Short
Normal
Long
ELECTRODE EXTENSIONS (STICKOUT)
Short
Normal
Long
FILLET WELD ELECTODE EXTENSIONS (STICKOUT)
Slow
Normal
GUN TRAVEL SPEED
OM-925 Page 34
Fast
S-0634
9-5.
Gun Movement During Welding
NOTE
Normally, a single stringer bead is satisfactory for most narrow groove weld joints;
however, for wide groove weld joints or bridging across gaps, a weave bead or
multiple stringer beads works better.
1
1
2
2
3
Stringer Bead − Steady
Movement Along Seam
Weave Bead − Side To Side
Movement Along Seam
Weave Patterns
Use weave patterns to cover a wide
area in one pass of the electrode.
3
S-0054-A
9-6.
Poor Weld Bead Characteristics
1
2
3
1
2
3
4
5
Large Spatter Deposits
Rough, Uneven Bead
Slight Crater During Welding
Bad Overlap
Poor Penetration
4
5
S-0053-A
9-7.
Good Weld Bead Characteristics
1
2
3
1
Fine Spatter
Uniform Bead
Moderate Crater During
Welding
Weld a new bead or layer for each
1/8 in (3.2 mm) thickness in metals
being welded.
4
5
2
3
4
No Overlap
Good Penetration into Base
Metal
5
S-0052-B
OM-925 Page 35
9-8.
Troubleshooting − Excessive Spatter
Excessive Spatter − scattering of molten metal particles that
cool to solid form near weld bead.
S-0636
Possible Causes
Corrective Actions
Wire feed speed too high.
Select lower wire feed speed.
Voltage too high.
Select lower voltage range.
Electrode extension (stickout) too long.
Use shorter electrode extension (stickout).
Workpiece dirty.
Remove all grease, oil, moisture, rust, paint, undercoating, and dirt from work surface before welding.
Insufficient shielding gas at welding arc.
Increase flow of shielding gas at regulator/flowmeter and/or prevent drafts near welding arc.
Dirty welding wire.
Use clean, dry welding wire.
Eliminate pickup of oil or lubricant on welding wire from feeder or liner.
Incorrect polarity.
9-9.
Check polarity required by welding wire, and change to correct polarity at welding power source.
Troubleshooting − Porosity
Porosity − small cavities or holes resulting from gas pockets
in weld metal.
S-0635
Possible Causes
Insufficient shielding gas at welding arc.
Corrective Actions
Increase flow of shielding gas at regulator/flowmeter and/or prevent drafts near welding arc.
Remove spatter from gun nozzle.
Check gas hoses for leaks.
Place nozzle 1/4 to 1/2 in (6-13 mm) from workpiece.
Hold gun near bead at end of weld until molten metal solidifies.
Wrong gas.
Use welding grade shielding gas; change to different gas.
Dirty welding wire.
Use clean, dry welding wire.
Eliminate pick up of oil or lubricant on welding wire from feeder or liner.
Workpiece dirty.
Remove all grease, oil, moisture, rust, paint, coatings, and dirt from work surface before welding.
Use a more highly deoxidizing welding wire (contact supplier).
Welding wire extends too far out of nozzle.
Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
9-10. Troubleshooting − Excessive Penetration
Excessive Penetration − weld metal melting through base metal
and hanging underneath weld.
Excessive Penetration Good Penetration
Possible Causes
Excessive heat input.
Corrective Actions
Select lower voltage range and reduce wire feed speed.
Increase travel speed.
OM-925 Page 36
S-0639
9-11. Troubleshooting − Lack Of Penetration
Lack Of Penetration − shallow
fusion between weld metal and
base metal.
Lack of Penetration
Good Penetration
S-0638
Possible Causes
Corrective Actions
Improper joint preparation.
Material too thick. Joint preparation and design must provide access to bottom of groove while
maintaining proper welding wire extension and arc characteristics.
Improper weld technique.
Maintain normal gun angle of 0 to 15 degrees to achieve maximum penetration.
Keep arc on leading edge of weld puddle.
Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
Insufficient heat input.
Select higher wire feed speed and/or select higher voltage range.
Reduce travel speed.
Incorrect polarity.
Check polarity required by welding wire, and change to correct polarity at welding power source.
9-12. Troubleshooting − Incomplete Fusion
Incomplete Fusion − failure of weld metal to fuse completely with
base metal or a preceeding weld bead.
S-0637
Possible Causes
Corrective Actions
Workpiece dirty.
Remove all grease, oil, moisture, rust, paint, undercoating, and dirt from work surface before
welding.
Insufficient heat input.
Select higher voltage range and/or adjust wire feed speed.
Improper welding technique.
Place stringer bead in proper location(s) at joint during welding.
Adjust work angle or widen groove to access bottom during welding.
Momentarily hold arc on groove side walls when using weaving technique.
Keep arc on leading edge of weld puddle.
Use correct gun angle of 0 to 15 degrees.
9-13. Troubleshooting − Burn-Through
Burn-Through − weld metal melting completely through base metal
resulting in holes where no metal remains.
S-0640
Possible Causes
Excessive heat input.
Corrective Actions
Select lower voltage range and reduce wire feed speed.
Increase and/or maintain steady travel speed.
OM-925 Page 37
9-14. Troubleshooting − Waviness Of Bead
Waviness Of Bead − weld metal that is not parallel and does not cover
joint formed by base metal.
S-0641
Possible Causes
Corrective Actions
Welding wire extends too far out of nozzle.
Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
Unsteady hand.
Support hand on solid surface or use two hands.
9-15. Troubleshooting − Distortion
Distortion − contraction of weld metal during welding that forces
base metal to move.
Base metal moves
in the direction of
the weld bead.
Possible Causes
Excessive heat input.
S-0642
Corrective Actions
Use restraint (clamp) to hold base metal in position.
Make tack welds along joint before starting welding operation.
Select lower voltage range and/or reduce wire feed speed.
Increase travel speed.
Weld in small segments and allow cooling between welds.
OM-925 Page 38
9-16. Common MIG Shielding Gases
This is a general chart for common gases and where they are used. Many different combinations (mixtures) of
shielding gases have been developed over the years. The most commonly used shielding gases are listed in the
following table.
Application
Gas
Spray Arc Steel
Short Circuiting Steel
Short Circuiting
Stainless Steel
Aluminum
X
Argon
X
Argon + 25% CO2
80% or greater Argon +
balance CO2 or Oxygen
X
X1
X
100% CO2
Tri-Mix2
X
1
Limited short circuiting use
2
90% HE + 7-1/2% AR + 2-1/2% CO2
9-17. Troubleshooting Guide For Semiautomatic Welding Equipment
Problem
Probable Cause
Wire feed motor operates, but Too little pressure on wire feed rolls.
wire does not feed
feed.
Incorrect wire feed rolls.
Wire curling up in front of the
wire feed rolls (bird nesting)
nesting).
Wire feeds, but no gas flows.
Remedy
Increase pressure setting on wire feed rolls.
Check size stamped on wire feed rolls, replace to match
wire size and type if necessary.
Wire spool brake pressure too high.
Decrease brake pressure on wire spool.
Restriction in the gun and/or assembly.
Check and replace cable, gun, and contact tip if
damaged. Check size of contact tip and cable liner,
replace if necessary.
Too much pressure on wire feed rolls.
Decrease pressure setting on wire feed rolls.
Incorrect cable liner or gun contact tip size.
Check size of contact tip and check cable liner length
and diameter, replace if necessary.
Gun end not inserted into drive housing properly.
Loosen gun securing bolt in drive housing and push gun
end into housing just enough so it does not touch wire
feed rolls.
Dirty or damaged (kinked) liner.
Replace liner.
Gas cylinder empty.
Replace empty gas cylinder.
Gas nozzle plugged.
Clean or replace gas nozzle.
Gas cylinder valve not open or flowmeter not adjusted.
Open gas valve at cylinder and adjust flow rate.
Restriction in gas line.
Check gas hose between flowmeter and wire feeder, and
gas hose in gun and cable assembly.
Loose or broken wires to gas solenoid.
Have Factory Authorized Service Agent repair wiring.
Gas solenoid valve not operating.
Have Factory Authorized Service Agent replace gas
solenoid valve.
Incorrect primary voltage connected to welding power Check primary voltage and relink welding power source
source.
for correct voltage.
OM-925 Page 39
Problem
Probable Cause
Remedy
Welding arc not stable.
Wire slipping in drive rolls.
Adjust pressure setting on wire feed rolls. Replace worn
drive rolls if necessary.
Wrong size gun liner or contact tip.
Match liner and contact tip to wire size and type.
Incorrect voltage setting for selected wire feed speed on Readjust welding parameters.
welding power source.
Loose connections at the gun weld cable or work cable. Check and tighten all connections.
Gun in poor shape or loose connection inside gun.
OM-925 Page 40
Repair or replace gun as necessary.
Notes
OM-925 Page 41
SECTION 10 − PARTS LIST
22
. Hardware is common and
24
36
31
40
54
42
41
44
46
45
51
50
47
1
43
48
38
33
39
30
32
2
49
37
34
35
3
4
29
5
6
7
8
28
9
52
10
11
27
12
13
26
25
17
23
16
19
15
14
18
20
21
53
not available unless listed.
803 716-B
Figure 10-1. Main Assembly
OM-925 Page 42
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-1. Main Assembly
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
9
10
11
12
13
13
14
15
15
16
17
18
18
19
20
20
21
22
23
24
25
25
26
26
27
27
28
29
30
31
32
33
34
35
36
37
37
38
39
40
. . . . . . . . . . . . . . . 199 566
. . . . . . . . . . . . . . . 196 006
. . . . . . . . . . . . . . . 211 887
. . . . . . . . . . . . . . . 204 608
. . . . . . . . . . . . . . . 202 998
. . . . . . . . . . . . . . . 203 072
. . . . . . . . . . . . . . . 211 339
. . . . . . . . . . . . . . . 202 726
. . . . . . . . . . . . . . . 217 072
. . . . . . . . . . . . . . . 217 078
. . . . . . . . . . . . . . . 195 999
. . . . . . . . . . . . . . . 210 109
. . . . . . . . . . . . . . . 196 467
. . . . . . . . . . . . . . . 216 397
. . . . . . . . . . . . . . . 216 398
. . . . . . . . . . . . . . . 197 198
. . . . . . . . . . . . . . . 147 545
. . . . . . . . . . . . . . . 152 118
. . . . . . . . . . . . . . . 111 443
. . . . . . . . . . . . . . . 137 761
. . . . . . . . . . . . . . . 196 063
. . . . . . . . . . . . . . . 196 064
. . . . . . . . . . . 409 953-001
. . . . . . . . . . . . . . . 217 096
. . . . . . . . . . . . . . . 217 389
. . . . . . . . . . . . . . . 208 015
. . . . . . . . . . . . . . +196 005
. . . . . . . . . . . . . . . 204 036
. . . . . . . . . . . . . . . 203 491
. . . . . . . . . . . . . . . 193 039
. . . . . . . . . . . . . . . 193 040
. . . . . . . . . . . . . . . 203 868
. . . . . . . . . . . . . . . 203 874
. . . . . . . . . . . . . . . 193 191
. . . . . . . . . . . . . . . 193 316
. . . . . . . . . . . . . . . 193 193
. . . . . . . . . . . . . . . 217 831
. . . . . . . . . . . 405 576-001
. . . . . . . . . . . . . . . 193 144
. . . . . . . . . . . . . . . 193 194
. . . . . . . . . . . . . . . 216 830
. . . . . . . . . . . . . . . 134 201
. . . . . . . . . . . . . . . 409 477
. . . . . . . . . . . . . . . 209 873
. . . . . . . . . . . . . . . 217 062
. . . . . . . . . . . . . . . 214 739
. . . . . . . . . . . . . . . 010368
. . . . . . . . . . . . . . . 196 619
. . . . . . . . . . . . . . . 196 575
. . DOOR, access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . HINGE, door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . HUB, nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SPRING, cprsn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WASHER, flat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . HUB, spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . ADAPTER, spool hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CIRCUIT CARD ASSY, control (115 VAC model) . . . . . . . . . . . . . . . . . . .
. . CIRCUIT CARD ASSY, control (230 VAC model) . . . . . . . . . . . . . . . . . . .
. . BASE, lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CIRCUIT BREAKER, 25 amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TUBING, PVC .187 ID x .312 OD x 24.000 . . . . . . . . . . . . . . . . . . . . . . . .
. . VALVE, gas (115 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . VALVE, gas (230 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CABLE TIE, .700-.799 bundle dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CORD SET, 125V 5−15P 14GA 3/C 7ft SPT−3 jkt (115 VAC model) . . .
. . CORD SET, 250V 6−50P 12GA 3/C 7ft SPT−3 jkt (230 VAC model) . . .
. . BUSHING, strain relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, gas valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . MOTOR, fan (115 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . MOTOR, fan (230 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . BLADE, fan cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TRANSFORMER, power assy (115 VAC model) . . . . . . . . . . . . . . . . . . . .
. . TRANSFORMER, power assy (230 VAC model) . . . . . . . . . . . . . . . . . . . .
. . HANDLE, carrying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WRAPPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . LABEL, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CLAMP, capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CAPACITOR, electlt 53000uf (115 VAC model) . . . . . . . . . . . . . . . . . . . . .
. . CAPACITOR, electrlt 100000uf (230 VAC model) . . . . . . . . . . . . . . . . . . .
. . REACTOR ASSY (115 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . REACTOR ASSY (230 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . RECTIFIER ASSY (115 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . RECTIFIER ASSY (230 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . BUS BAR (positive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . BAFFLE, center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . BUSHING, terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . INSULATOR, output stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . BUS BAR (negative) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . LABEL, warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . STAND-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SWITCH, rotary 25A 5 position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . POTENTIOMETER, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . PANEL, front (purple) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . PANEL, front (black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CLAMP, work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CABLE, work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SWITCH, rocker SPST (115 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
OM-925 Page 43
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-1. Main Assembly (Continued)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
40
41
42
43
44
45
46
47
48
49
50
50
50
50
51
52
52
53
54
. . . . . . . . . . . . . . . 196 574 . . SWITCH, rocker DPST (230 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 207 079 . . KNOB, pointer (voltage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 211 338 . . KNOB, pointer (WFS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 217 778 . . MOTOR, gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 193 189 . . CONNECTOR, gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 196 654 . . SCREW, thumb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 196 009 . . FITTING, gas barbed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 202 925 . . ROLL, feed .024 in, .030/.035 in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 194 508 . . HEAD, feed assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 203 025 . . GUIDE, wire inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 217 618 . . LABEL, weld chart (115 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 221 079 . . LABEL, weld chart (115 VAC model) (French) . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 217 754 . . LABEL, weld chart (230 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 221 080 . . LABEL, weld chart (230 VAC model) (French) . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 204 711 . . LATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 217 584 . . CONTACTOR (115 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 217 585 . . CONTACTOR (230 VAC model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 203 572 . . LABEL, warn gen precaution (EN/FR models only) . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . LABEL, nameplate (order by model and serial number) . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-925 Page 44
1
3
2
4
5
6
7
9
8
11
10
802 447
Figure 10-2. H-10 Gun
Item
No.
Part
No.
195 957
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
2
2
2
3
4
5
6
7
8
9
9
9
9
10
11
. . . . . . . . . . . . . . . 169 715
. . . . . . . . . . . . . ♦087 299
. . . . . . . . . . . . . ♦000 067
. . . . . . . . . . . . . ♦000 068
. . . . . . . . . . . . . ♦000 069
. . . . . . . . . . . . . . . 169 716
. . . . . . . . . . . . . . . 170 470
. . . . . . . . . . . . . . . 169 718
. . . . . . . . . . . . . . . 169 738
. . . . . . . . . . . . . . . 169 719
. . . . . . . . . . . . . . . 079 975
. . . . . . . . . . . . . ♦194 010
. . . . . . . . . . . . . ♦194 011
. . . . . . . . . . . . . ♦194 012
. . . . . . . . . . . . . ♦194 014
. . . . . . . . . . . . . . . 197 123
. . . . . . . . . . . . . . . 196 255
Description
Quantity
Figure 10-2. H-10 Gun
. . . . NOZZLE, slip type .500 orf flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . TIP, contact scr .023 wire x 1.125
. . . . TIP, contact scr .030 wire x 1.125
. . . . TIP, contact scr .035 wire x 1.125
. . . . TIP, contact scr .045 wire x 1.125
. . . . ADAPTER, contact tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . RING, retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . TUBE, head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . NUT, locking handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . NUT, jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . O-RING, .187 ID x .103CS rbr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . LINER, monocoil .023/.025 wire x 15ft (consisting of) . . . . . . . . . . . . .
. . . . LINER, monocoil .030/.035 wire x 15ft (consisting of) . . . . . . . . . . . . .
. . . . LINER, monocoil .035/.045 wire x 15ft (consisting of) . . . . . . . . . . . . .
. . . . LINER, monocoil 4/64 AL wire x 10ft nyl(consisting of) . . . . . . . . . . . .
. . . . O-RING, .312 ID x .062 70 Dura BUNA-N . . . . . . . . . . . . . . . . . . . . . . .
. . SWITCH, trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
1
1
1
1
1
1
2
1
♦OPTIONAL
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-925 Page 45
10-3. Optional Drive Rolls
For All Feed Head Assemblies
PART NO.
WIRE DIAMETER
INCHES (mm)
202 925
.023/.025 (.6) and .030/.035 (.8 and .9)
202 926
.030/.035 (.8 and .9) and .045 (1.2 VK Groove)
10-4. Options
PART NO.
DESCRIPTION
REMARKS
770 187
Running Gear/Cylinder Rack
For One Small Gas Cylinder, 100 lb (45 kg) max.
194 776
Small Running Gear/Cylinder Rack
For One Small Gas Cylinder, 75 lb (34 kg) max.
195 957
H-10 Replacement Gun
10 ft length/.030-.035 wire size
195 186
Protective Cover
Weatherproof nylon
212 492
Regulator/Flowmeter
For use with CO2 shielding gas, 10−50 CFH
NOTE: If individual parts are required, see Parts List chapter of this manual for part number to order.
OM-925 Page 46
Effective January 1, 2003
Warranty Questions?
Call
1-877-HOBART1
for your local
Hobart distributor.
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor or
call 1-800-332-3281. The
expertise of the distributor
and Hobart is there to
help you, every step of
the way.
5/3/1 WARRANTY applies to all Handler 125, 135 and 175 models, Airforce 250, 250A, 375, 400
and 625 models, and Champion 4500 and 10,000 models, Beta-Mig 1800, Champ 1435, 2060, 8500
models, Ironman 210 and 250 models, Stickmate models, Tigmate models, and HSW-15 and
HSW-25 spot welder models effective with Serial No. KK200262 and newer.
This limited warranty supersedes all previous Hobart warranties and is exclusive with
no other guarantees or warranties expressed or implied.
Hobart products are serviced by Hobart or Miller Authorized Service Agencies.
LIMITED WARRANTY − Subject to the terms and conditions
below, Hobart/Miller Electric Mfg. Co., Appleton, Wisconsin,
warrants to its original retail purchaser that new Hobart
equipment sold after the effective date of this limited warranty is
free of defects in material and workmanship at the time it is
shipped by Hobart. THIS WARRANTY IS EXPRESSLY IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS.
Within the warranty periods listed below, Hobart/Miller will repair
or replace any warranted parts or components that fail due to
such defects in material or workmanship. Hobart/Miller must be
notified in writing within thirty (30) days of such defect or failure, at
which time Hobart/Miller will provide instructions on the warranty
claim procedures to be followed.
Hobart/Miller shall honor warranty claims on warranted
equipment listed below in the event of such a failure within the
warranty time periods. All warranty time periods start on the date
that the equipment was delivered to the original retail purchaser,
or one year after the equipment is sent to a North American
distributor or eighteen months after the equipment is sent to an
International distributor.
1.
2.
3.
4.
5 Years — Parts and Labor
*
*
Original Main Power Rectifiers
Transformers
*
*
Stabilizers
Reactors
3 Years — Parts and Labor
*
*
Drive Systems
PC Boards
*
*
Rotors, Stators and Brushes
Idle Module
*
*
Solenoid Valves
Switches and Controls
*
Spot Welder Transformer
1 Year — Parts and Labor Unless Specified
(90 days for industrial use)
*
*
Motor-Driven Guns
MIG Guns/TIG Torches
*
*
*
Relays
Contactors
Regulators
*
*
*
Water Coolant Systems
Flowgauge and Flowmeter Regulators (No Labor)
HF Units
*
*
Running Gear/Trailers
Plasma Cutting Torches
*
*
Remote Controls
Replacement Parts (No labor)
*
*
Accessories
Field Options
(NOTE: Field options are covered for the remaining
warranty period of the product they are installed in, or
for a minimum of one year — whichever is greater.)
Engines, batteries and tires are warranted separately by the
manufacturer.
Hobart’s 5/3/1 Limited Warranty shall not apply to:
1.
Consumable components such as contact tips, cutting
nozzles, slip rings, drive rolls, gas diffusers, plasma
torch tips and electrodes, weld cables, and tongs and
tips, or parts that fail due to normal wear. (Exception:
brushes, slip rings, and relays are covered on Hobart
Engine-Driven models.)
2.
Items furnished by Hobart/Miller, but manufactured by
others, such as engines or trade accessories. These items
are covered by the manufacturer’s warranty, if any.
3.
Equipment that has been modified by any party other than
Hobart/Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
HOBART PRODUCTS ARE INTENDED FOR PURCHASE AND
USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS
TRAINED AND EXPERIENCED IN THE USE AND
MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Hobart’s/Miller’s option: (1) repair;
or (2) replacement; or, where authorized in writing by
Hobart/Miller in appropriate cases, (3) the reasonable cost of
repair or replacement at an authorized Hobart/Miller service
station; or (4) payment of or credit for the purchase price (less
reasonable depreciation based upon actual use) upon return of
the goods at customer’s risk and expense. Hobart’s/Miller’s
option of repair or replacement will be F.O.B., Factory at
Appleton, Wisconsin, or F.O.B. at a Hobart/Miller authorized
service facility as determined by Hobart/Miller. Therefore no
compensation or reimbursement for transportation costs of any
kind will be allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL HOBART/MILLER BE
LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY
OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND
ANY
IMPLIED
WARRANTY,
GUARANTY
OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION, OPERATION OF LAW,
CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO
ANY
AND
ALL
EQUIPMENT
FURNISHED
BY
HOBART/MILLER IS EXCLUDED AND DISCLAIMED BY
Hobart/Miller.
Some states in the U.S.A. do not allow limitations of how long an
implied warranty lasts, or the exclusion of incidental, indirect,
special or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty provides specific
legal rights, and other rights may be available, but may vary from
state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations and
exclusions set out above may not apply. This Limited Warranty
provides specific legal rights, and other rights may be available,
but may vary from province to province.
hobart retail 8/03
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
Resources Available
Always provide Model Name and Serial/Style Number.
To locate a Distributor,
retail or service location:
Call 1-877-Hobart1 or visit our website at
www.HobartWelders.com
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
For technical assistance:
Call 1-800-332-3281
Service and Repair
Replacement Parts
Training (Schools, Videos, Books)
Hobart Welding Products
Technical Manuals (Servicing Information
and Parts)
An Illinois Tool Works Company
600 West Main Street
Troy, OH 45373 USA
Circuit Diagrams
For Technical Assistance:
Call1-800-332-3281
For Literature Or Nearest Dealer:
Call 1-877-Hobart1
Welding Process Handbooks
Contact the Delivering Carrier to:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims, contact
your distributor and/or equipment manufacturer’s
Transportation Department.
PRINTED IN USA
 2003 Hobart Welding Products.
1/03
Download PDF