PARADOX Insight HD77 Installation manual

Add to my manuals
36 Pages

advertisement

PARADOX Insight HD77 Installation manual | Manualzz
Paradox Insight™
HD77
Installation Guide
Revision 1.00
paradox.com
HD77 Installation Guide
1
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on
the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all
warranty terms and conditions. Please ensure compliance with the applicable laws of local jurisdictions
including privacy laws.
© 2014 Paradox Ltd. All rights reserved. Specifications may change without prior notice. Canadian and
international patents may apply. EVOHD Digiplex is a trademark or registered trademark of Paradox Ltd. or its
affiliates in Canada, the United States and/or other countries. LODIFF® is a registered trademark of Fresnel
Technologies Inc.
For the latest information on products approvals, such as UL and CE, please visit www.paradox.com.
Note:
This hardware or software product (“product(s)”) and its related documentation are provided by
Paradox for use complying with all local, national, and international laws. any express or implied
warranties, including, but not limited to, the implied warranties of merchantability, fitness for a
particular purpose and noninfringement are disclaimed. In no event shall Paradox be liable to any
customer or third party for any direct, indirect, special, exemplary, or consequential damages of any
kind (including, but not limited to, payment for procurement of substitute goods or services; loss of
property, data, or profits; or business interruption) however caused and on any theory of liability,
whether in contract, strict liability, or tort (including negligence or otherwise) arising in any way from
the use of the product(s) and related documentation.
This product is manufactured in Canada.
Paradox
780 Industrial Boulevard
St-Eustache, Quebec
Canada, J7R 5V3
Tel: (450) 491-7444
Fax: (450) 491-2313
Contents
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1
HD77 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.3
LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Chapter 2
Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2
Location and Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.3
HD77 Installation (Wall or Corner Mount) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Chapter 3
Configure IP Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1
Setting Up the Router for Port Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2
Reserve the IP or Bind the IP to a MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 4
HD77 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1
PIR programming Through BabyWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2
System Programming Through BabyWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.3
Registering your Customer’s System with ParadoxMyHome . . . . . . . . . . . . . . 27
4.4
Upgrading Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 5
Insight Application Configuration . . . . . . . . . . . . . . . . . . . . . . . . 31
Appendix: A
Specifications ............................................................................32
HD77 Specifications ............................................................................................................32
Appendix: B
PIR Detector Beam Pattern .......................................................33
Appendix: C
Certifications .............................................................................34
HD77 Installation Guide
3
Introduction
1
Introduction
1
The Paradox HD77 is an HD video & audio camera with superior PIR detector. HD77 is a high-performance HD
720p color camera, and a microphone with an integrated PIR detector. It offers superior motion detection with
video verification, for areas up to 12m x 12m (40ft x 40ft).
The HD77 enables streaming Video On Demand (VOD) and Record On Demand (ROD) functionality using the
Insight Application. Video and JPEG outputs can be sent to the IPRS-7 monitoring software and to the user's
email to help determine the cause of an alarm, and apply an appropriate response to the situation.
The HD77 provides 24/7 continuous monitoring of your property. The high definition digital video camera
transmits a color signal at 360p resolution during normal light conditions. During periods of low light the HD77
supplies IR illumination that supports the HD77 camera down to zero lumens of light with black and white
signal transmission.
The high quality microphone supplements the video with superior quality audio.
The system’s master user can ensure privacy by setting viewing rights by user. This can be done through the
Paradox Insight app. The HD77 also increases privacy and security by storing video recordings within the
module. This way any recordings are more secure than video files stored on a pubic or private server. The
module only records upon a detection event or when Record On Demand is enabled.
The HD77 is user-centered and respects user privacy. There are 2 levels of authorization. The lower level
authorized users receive 15 minutes of viewing after an alarm. The higher level authorized users have unlimited
viewing and authorization to Record On Demand.
Recording only takes place when an alarm is triggered, or when an authorized user implements Record On
Demand. Each time ROD is enabled the recording is limited to 5 minutes. Images sent to the CMS include only
those from actual alarm events, as defined during installation. Recordings of events remain in control of the
user and are stored within the HD77 device. The master user can download the recordings at his convenience
and to his preferred files location.
1.1 HD77 Key Features
•
•
•
•
•
•
•
•
•
•
•
•
•
4
HD 720p 1.4 Mega Pixel color image sensor
Video and Audio H.264 streaming for VOD and ROD
Paradox patented PIR technology
Video verification of an alarm event viewable by IPRS-7/CMSI or the Mobile application
Integrated email client to send notification of events as video and/ or images
Multiple simultaneous multimedia streams
Event file names and video file names are linked through the naming convention for easy identification
Auto Gain Control, Auto White Balance, Auto Exposure
Zero-lux vision using high power IR LEDs
Microphone for high quality sound transmission
4 GB Micro SD card
Digibus connection to Paradox EVOHD Panel
LAN connection
HD77 Installation Guide
1.2 Overview
The Paradox HD77 is an HD video and audio camera with a superior PIR detector.
P A R A D O X
Camera
Microphone
IR LEDs
TX
RX
Information
LED 1
LED 2 LED 3 LED 4 LED 5
Figure 1 – Front view
1.3 LED Status Indicators
The following table describes the HD77 LEDS and their functionality.
TX
RX
LED 1 LED 2 LED 3 LED 4 LED 5
Figure 2 – LED Arrangement
LEDs 1, 2, 4, and 5 are used for installer diagnostics. These LEDs are active after boot up, when the lock
mechanism is opened.
HD77 Installation Guide
5
Table 1: LED Status Indicators
LED
Functionality
LED assignment
LED1
Data TX
Flashing green = data
transmission
Off = No data
LED2
Data RX
Flashing green = data
reception
Off = No data
LED3
(both with the case
locked and
unlocked)
HD77 module is up and running. There are currently no
alarms or requests for VOD/ROD.
OFF
Firmware upgrade in progress
Flashing Purple
VOD (no PIR detection)
Blue on
Power-up (PIR stabilization and CPU not fully ready –
waiting for all labels)
Flashing Blue
Locate mode
Flashing Blue
General bus failure, wiring problem, too many modules
communication problem
Red on
Bus low power
Flashing Red
PIR alarm
Red for 5 sec
LED4
Active Web connection
Green
LED5
100MB/10MB link
100MB/10MB data TX or RX
Green = LAN Active
Off = No Connection
Flashing green on data
Important - LED3: PIR indication can be set to On or Off by the installer, however, the VOD indication can be
turned off only by the master user using the Insight application.
Turning the VOD LED off may be considered in some countries as a violation of applicable laws. Make sure to
install the HD77 according to Local Laws.
6
HD77 Installation Guide
Hardware Installation
2
Hardware Installation
2
This section explains the hardware requirements and mounting instructions.
2.1 Requirements
Before you start the installation make sure you have all of the required infrastructure, tools and software.
2.1.1 Hardware
Note:
A singleCAT5 or higher cable can be used to wire a single HD77 camera. This cable includes 2 twisted
pairs for the 4-wire combus and 2 twisted pairs for the Ethernet lines. When using this option the cable
length is limited to 50 meters. When using this option the cable length is limited to 50 meters.
Note:
An alternate wiring scheme is to wire the HD77 with two separate cables. 1 Ethernet cable and 1– 4wire combus.
In order to take full advantage of all that the Insight Solution has to offer ensure that the mounting location has
the following infrastructure:
• 4-wire combus cable that connects to the EVOHD
• Ethernet line that connects to a router or Ethernet switch
• a router with enough ports to connect all of the cameras (1 port for each camera) plus 1 port if you are
using an IP150, 1 port for your computer, and 1port for the incoming internet connection
If the router does not have enough ports you will also need a switch.
The router will need to be configured for port forwarding for the HD77. Each HD77 in the system will
have a different IP address and each one will need port forwarding to two ports of its IP address. One
from the external IP address:port (any port above port #1024) to the internal <IP address>:80 and
one for <IP address>:443.
The installer will also need to have the following job specific tools and equipment:
• a laptop with Windows 7
• a connection from your laptop to the system either by:
• 307USB cable
OR
• IP150 Internet module to connect to the EVOHD serial port
Figure 3 – Recommended wiring for using the oneCAT5 or higher cable
HD77 Installation Guide
7
Figure 4 – HD77 Hardware Connections
2.1.2 Software
The installer will also need to have the following software available on his laptop.
• BabyWare Installer software V 2.5 or higher (downloadable from paradox.com)
• Paradox IP Exploring Tool V1.66 or higher (downloadable from paradox.com)
2.2 Location and Mounting
Follow the recommendations and cautions in order to get the most out of your system.
2.2.1 Recommendations
• Install the device at a height between 2.1m to 2.7m (7ft to 9ft), allowing a minimum gap of 2cm (~1 in)
from the ceiling (to allow for opening/closing of the cover).
8
HD77 Installation Guide
Figure 5 – Mounting Guidelines
• Install the device in a location where the detector and camera’s field of view is clear of any obstacles.
• For LAN connection, use a CAT5e/CAT6 Ethernet cable (70m Max.) between the HD77 and the router.
• Mount the module so that walking traffic cuts across the beam pattern.
2.2.2 Cautions
• Do not install the device near objects causing temperature changes such as heaters, refrigerators and
ovens.
• Do not install the device in the path of air flow from vents, fans or windows.
• Do not install the device in the path of reflective surfaces, direct sunlight or infrared light.
• Do not install the device where it is exposed to oil vapors or steam.
• Do not touch the sensor surface or the camera lens as this could result in a detector malfunction.
2.3 HD77 Installation (Wall or Corner Mount)
1. Separate the front from the back plate of the HD77:
Step 1.
Open the lock mechanism at the bottom of the device.
Step 2.
Pry the cover off from the bottom of the unit.
Step 3.
Lift the front cover up and away. On the back of this module you will see the serial number.
Step 4.
Knock out the appropriate holes on the back plate. Use an awl or an ice pick.
Step 5.
Write the serial number of the module into your module table. Include the exact location of this
module. If you are using BabyWare the serial number will be displayed, but you will need to
write down the correct location for each module serial number.
2. Ensure to include the wall tamper knockout for the installation.
HD77 Installation Guide
9
Wall mount
Corner mount
Ceiling
Anti-Tamper
Anti-Tamper
For wall
installation
For corner
installation
R B G Y Rx- RX+ TX-Tx+
R B G Y Rx- RX+ TX-Tx+
Figure 6 – Knockout Locations
3. Secure the back plate to the wall at the location:
Note:
10
Step 1.
Install the device a minimum of 2cm (~1 in) from the ceiling, between 2.1m and 2.7m off the
floor.
Step 2.
Insert the Ethernet and 4-wire combus cables through the wiring slot of the back plate.
Step 3.
Secure the back plate to the wall with screws. (use wall anchors if required).
Step 4.
Ensure that the wall tamper knockout is secured to the wall.
Step 5.
Wire up both the 4-wire combus and the Ethernet cable.
Step 6.
Connect the wires to the terminal board as seen in Figure 8 on page 11 and Figure 7 on page 11.
A singleCAT5 or higher cable can be used to wire a single HD77 camera. This cable includes 2 twisted
pairs for the 4-wire combus and 2 twisted pairs for the Ethernet lines. When using this option the cable
length is limited to 50 meters. When using this option the cable length is limited to 50 meters.
HD77 Installation Guide
Figure 7 – Recommended wiring for using theCAT5 or higher cable option.
4-wire combus
Ethernet
R
B
G
Y RD- RD+TD- TD+
Figure 8 – HD77 2 Cables Wiring
Note:
These are 2 separate cables going to two different locations. One cable to the router and one cable to
the EVOHD.
Step 7.
Slack wire should not interfere with closing the cover.
HD77 Installation Guide
11
4. Place the front cover onto the back plate:
Step 1.
Install the top of the unit first.
Step 2.
Close the HD77 onto the back plate.
Step 3.
Close the lock mechanism at the bottom of the device. (note that by securing the lock, the technician indication LEDs will be turned off ).
5. Connect the Ethernet line to the router (if not already connected). Make sure the router is turned on.
6. Connect the Ground from the power line to the metal box and to the GND connector on the EVOHD board.
If a plastic box is used connect the power ground to the GND connector on the EVOHD board directly.
Warning:
Connect the box and board to a valid ground connection.
7. After the whole system hardware is connected power up the system by connecting the power lines from
the 16V AC transformer to an outlet.
Note:
This outlet must not have any in-line switches!
8. The system will boot-up including the HD77s.
The HD77 boot-up is indicated by LED3. The LED will flash blue for up to 3 minutes.
12
HD77 Installation Guide
Configure IP Router
3
Configure IP Router
3
With the IP150 and Cameras wired to the router, perform the port forwarding and reserve the IP addresses of
the IP150 and the HD77cameras.
Determine if this job site has a network administrator. See if he is able to assist you in this part of the
installation.
Note:
This procedure is dependent upon the individual router and network security for the end user’s system.
The end user’s router may require a different procedure.
The following provides an example for one type of router. Refer to the router manufacturer's documentation for
detailed instructions. If the end user does not have his router documentation you can find the correct
instructions on the internet.
3.1 Setting Up the Router for Port Forwarding
Following is an example of instructions for port forwarding.
Note:
The end users specific router may require different instructions.
EXAMPLE:
1. Ensure that the router is connected properly as indicated in the router’s instructions.
2. Access your router’s configuration page:
Step 1.
Refer to your router’s manual for the exact procedure. In most cases, this is done by entering
the router’s IP address in the address bar of your web browser. Your router’s IP address may be
indicated in the router’s instructions or on a sticker on the router.
Step 2.
If you cannot find the IP address of the router, try the following from your Windows Screen:
Step a. Open a command prompt window. Press the windows button on your keyboard.
In the search programs and files window type in Command.
Step b. Select Command Prompt.
Step c. At the prompt Type ipconfig
Step d. Press Enter.
The router IP address will be the Default Gateway . . . . .:xx.xx.xx.xxx
HD77 Installation Guide
13
Figure 9 – Command Prompt ipconfig
Step e. Enter this IP address into the address bar at the top of the browser page. Press
Enter.
Step f.
Step 3.
14
Put in the user name and password. If you do not know the user name and password, go to the site www.routerpasswords.com and select your router manufacturer and model. The default user name and password should be listed.
For this instruction sheet, we will use 10.0.0.138 as an example, since it is the router IP address
seen in Figure 9.
HD77 Installation Guide
3. In the router’s configuration page, check the DHCP settings:
Step 1.
If DHCP is enabled, verify that the IP address range is large enough to accommodate all of your
cameras. Four cameras will require 4 IP addresses.
Figure 10 – DHCP Enable
Step 2.
Record one address at the upper end of the DHCP range for each HD77 in your system. You will
need two ports for each IP address one port for (port 80) for HTTP and one port for (port 443)
for HTTPS.
Step 3.
DHCP Settings (screenshot may differ depending on type of router used).
Figure 11 – Port Forwarding
Figure 12 – Fill in the Port Forwarding Information
HD77 Installation Guide
15
4. In the router’s configuration page, go to the Port Forwarding section (also known as “port mapping”, "NAT",
(network address translation), or “port redirection”).
5. Select an available port on the router and assign it to the HD77 camera. Select a port above #10000 for the
external port. This will be internal port 80 on the camera side. For example, set the router port number to
10166 (assuming that it is available) to HD77 port 80. The HD77 IP address according to the IP Exploring
tool is 10.0.0.166:10166.
6. Repeat the procedure using the same IP address, select the next consecutive port and assign it to port 443
for HTTPS.
16
HD77 Installation Guide
Note:
As a suggested standard try to assign the port so that it has 10 + the last section of the IP address.
In step 5 above notice that The IP address is 10.0.0.166 and the port # is 10166. The port number is
chosen arbitrarily by the installer. Choosing the port number to match the IP address will make
configuration easier.
Example of IP addresses and ports for 4 cameras.
Table 2: List of Cameras
Camera name
Location
IP Address
Living room
facing front door
10.0.0.166
Den
Safe room
2nd floor
Note:
facing sliding rear
door
10.0.0.168
facing the safe
10.0.0.170
looking down the
staircase
External port
number
Internal port
number
10166
80
10167
443
10168
80
10169
443
10170
80
10171
443
10172
80
10173
443
10.0.0.172
Each camera needs a separate IP address and matching external port.
Figure 13 – HD77 IP Address
Note:
The IP Exploring tool must be closed before you try and connect to the EVOHD panel through
BabyWare.
3.2 Reserve the IP or Bind the IP to a MAC
You need to bind the IP address of the HD77 to a MAC address in your router. This is called reserving an IP
address or binding an IP address.
This is done on the router, just like you connected to the router for port forwarding you will need to connect for
reserving a port. This should be under the LAN properties.
HD77 Installation Guide
17
Since each router is different you may need to use the router user manual or search online for instructions for
your particular router.
You can also try searching the internet for videos on routers and reserving IP addresses (screenshots may differ
depending on type of router used).
Router Configuration page
Paradox IP Exploring Tool
Figure 14 – Binding or Reserving a Port
Once the IP is successfully reserved:
1. Make sure that you are disconnected from BabyWare.
2. Open the IP Exploring Tool.
3. Right click the HD77 camera.
4. Select Module Setup.
5. Check the box for “Obtain an IP address automatically”. This means that DHCP is enabled.
6. Put in the Module password [paradox].
7. Click OK.
18
HD77 Installation Guide
HD77 Programming
4
HD77 Programming
4
All PIR parameters of the HD77 can be configured by the installer using the TM50 touchpad, the K641 plus
keypad, and by using BabyWare software. Server parameters must be programmed through BabyWare, only.
Note:
To program the module sections from any keypad BabyWare must be disconnected from the system.
Note:
ALWAYS DO A READ before programming.
4.1 PIR programming Through BabyWare
1. In BabyWare under the Security Modules double click the HD77 modules or right click the HD77 module
and Click Properties. The HD77 Programming screen appears.
Note:
Due to our constant efforts to improve our products the software screen grabs may not be exactly the
same as your screen.
Figure 15 – BabyWare Main Screen
Note:
This may take up to 1 minute.
2. Wait for the properties to appear.
3. Use VOD to verify Camera vision / image / angle.
In BabyWare => HD77 Properties => Video tab => play button
HD77 Installation Guide
19
Figure 16 – HD77 Video Stream in BabyWare
4. Configure PIR settings.
Note:
Always do a Receive Programming before configuring.
Figure 17 – Receive Programming
5. Select the configuration parameters (See Figure 18 on page 21):
• Show PIR LED Check this box to activate LED#3 to display when PIR motion is detected LED#3 lights up Red.
When this box not checked LED#3 stays off when PIR motion is detected. – Default is on.
• PIR sensitivity level – Default is #3.
Sensitivity level 1 is low sensitivity, useful for a room with large windows, or a small room.
Sensitivity level 5 is high sensitivity, useful for a large room with small windows.
• PIR Security level – Default is Normal.
20
HD77 Installation Guide
Sensitivity level “Normal” is low sensitivity, useful for a room with large windows, light curtains that
may move when the window is open, or a room with windows on the sunny side of the hose.
Sensitivity level “High” is high sensitivity, useful for a large room with small windows not on the
sunny side of the house, big heavy curtains.
Figure 18 – PIR Parameters
6. Perform a walk test to verify that detection is good.
4.2 System Programming Through BabyWare
Note:
Every parameter configurable through the programming guide is accessible and configurable through
BabyWare.
HD77 Module parameters
1. Use Babyware to configure the system: module names, labels, zones, partition assignments, arming
settings etc.
2. Confirm that the IP address field contains the correct IP address. If not use the IP Exploring tool.
HD77 Installation Guide
21
Figure 19 – Server Parameters
PIR Programming Through the TM50 touchpad
Only PIR parameters for the HD77 can be configured through the touchpad.
Home
Screen
System
Programming
Menu
Enter
[4003]
Advanced
Enter serial
number
Installer
programming
Enter Next
Enter
Installer code
Enter Module
Section
Select
options
Figure 20 – Flow through the TM50 Touchscreen
1. Select the [Menu] key.
22
HD77 Installation Guide
Figure 21 – Main Screen
2. Select the [Advanced] key.
Figure 22 – Menu Selections Screen
3. Select the [Installer Programming] key.
Figure 23 – Advanced Screen
HD77 Installation Guide
23
4. Enter your [Installer Code].
Figure 24 – Installer Code
5. Select the [System Programming] key.
Figure 25 – Installer Programming Screen
6. Key in Section [4003].
Figure 26 – Installer Programming Screen
24
HD77 Installation Guide
7. Enter the module’s [Serial Number]. Click Next.
Figure 27 – Module Serial Number Screen
8. Enter Section [001].
Figure 28 – Programming Section
9. Option 1 is for PIR LED On/Off;
On – LED#3 is will light up Red when PIR motion is detected.
Off – LED#3 stays off when the PIR motion is detected.
Default is On.
Options 2 through 8 are not relevant for the HD77.
Figure 29 – Options Selection Screen
10. Enter Section [002].
11. Select PIR sensitivity level, level 1 to level 5 – Default is #3.
12. Enter Section [003].
13. Select PIR security level, level 1 to level 3 – Default is #1.
HD77 Installation Guide
25
PIR Programming Through the K641+ keypad
Only PIR parameters for the HD77 can be configured through the touchpad.
1. Press and hold the [0] key. The installer will be asked to input his installer code.
2. Enter your [Installer Code]. The default installer code is 000000.
3. Key in Section [4003].
4. Enter the module’s [Serial Number].
5. Enter Section [001].
6. Option 1 is for PIR LED On/Off; On – LED#3 is Red when PIR motion is detected. Off – LED#3 stays off when
the PIR motion is detected.
Default is On
Options 2 through 8 are not relevant for the HD77.
7. Enter Section [002].
8. Select PIR sensitivity level, level 1 to level 5. Default is level 3.
9. Enter Section [003].
10. Select PIR security level, level 1 to level 3. Default is level 1.
PIR Settings
Table 3: PIR Configuration Settings
Description
Section
Setting
Setting Details
Example
1. PIR LED display
[001]
[1] Off
[1] On
PIR LED Off
PIR LED On
(1*******)
2. PIR Sensitivity
[002]
[1]
Low (Sensitivity level)
(001) 000-005
[2]
[3]
Default
[4]
3 Security Level
26
[003]
[5]
High (Sensitivity level)
[1]
Normal
(Mild environment)
[2]
Medium
[3]
High (Harsh
environment)
(001) 000-003
HD77 Installation Guide
4.3 Registering your Customer’s System with ParadoxMyHome
ParadoxMyHome is a Paradox Domain Name System (DNS) service that enables the user/installer to remotely
access a Paradox Reporting Device (e.g. IP150 or HD77) connected to an Internet Service Provider that uses
dynamic IP addresses. A dynamic IP address is assigned automatically, and can change on a regular basis.
ParadoxMyHome keeps track of these changes and will associate it to a Site ID (e.g. John house).
If you do not already have an account at ParadoxMyHome you will need to open one. Using any Browser go to
ParadoxMyHome.com. Click on Create Login, and follow the directions.
4.3.1 Setting up ParadoxMyHome
Using the ParadoxMyHome service will allow you to access your system over the Internet with a dynamic IP
address. The HD77 will then poll the ParadoxMyHome server to keep the information updated. To set up the
ParadoxMyHome service:
1. Go to www.paradoxmyhome.com.
2. Click Request Login and provide the requested information.
4.3.2 Registering the HD77 to ParadoxMyHome
1. Start the Paradox IP Exploring Tools software and right-click the HD77.
2. Select Register to ParadoxMyHome (choose a site ID or use the one created for the IP150).
Figure 30 – IP Exploring Tool
3. Enter the requested information. The SiteID should be unique for the module.
HD77 Installation Guide
27
Figure 31 – ParadoxMyHome Registration Page
Figure 32 – Registration Successful
4. Ensure the HD77 has access to reach the public network.
5. Verify HD77 updated PMH with status, public IP and ports.
Figure 33 – ParadoxMyHome Site
28
HD77 Installation Guide
4.3.3 Deleting a Site from PMH
When deleting a site form my PMH you may get an error message that the site still exists. If you delete a site
from PMH on the registered devices page you then have to go to the Deleted devices page and delete it again
from there. Or else PMH keeps the site just like the Windows recycle bin makes you empty your recycle bin after
you have already deleted your file.
Note:
To delete a site from PMH first delete the site from the Registered devices page and then delete it from
the Deleted Devices page.You must delete your site from BOTH pages.
4.4 Upgrading Firmware
1. Use Babyware to upgrade firmware on all of HD77s on your site. To update FW on the HD77 you will need
BabyWare V2.5 or higher.
2. Double click on any connected HD77 module listed in BabyWare.
Figure 34 – Select HD77
3. On the HD77 programing page click Update.
Figure 35 – Update button
HD77 Installation Guide
29
The following window opens up.
Figure 36 – Click Update
4. Click Update in this window. This will take a few minutes.
5. In order to see if the FW upgrade was successful, after the camera boots up you will need to disconnect and
reconnect to BabyWare. You can also close down and restart BabyWare.
30
HD77 Installation Guide
Insight Application Configuration
5
Insight Application Configuration
5
After installing the Insight application on your smart phone, the application will start in the “System Settings”
screen.
1. Enter the desired site label, provide a valid site ID [Registered to ParadoxMyHome] (as provided by your
installer), and a server password (default: paradox).
2. Tap “OK”, if the communication to the site was validated, you will be able to proceed and click “Next”.
3. The new site will appear on the dashboard, showing its status, and allowing you to login using your security
system user code (the same one you use to turn off the alarm system when you get in to your home or
business).
Figure 37 – System Settings
HD77 Installation Guide
31
Appendix: A
Specifications
HD77 Specifications
Table 4: HD77 Specifications
Image sensor type
1.4 Mega pixel, CMOS sensor
Voltage input
Nominal: 12VDC, range 9-16VDC
Current consumption
330 mA RMS
Installation Height
2.1 m - 2.7 m (7 ft - 9 ft)
Installation Options
Wall or corner, optional swivel bracket
Coverage
12 m x 12 m (40 ft x 40 ft) / 110°
PIR Type
Quad PIR, Auto pulse,
Auto dual edge, Digital detector
Micro SD card size
4GB
Camera recording resolution
720p
Streaming video resolution
360p
Video on Demand recording time
2 minutes each
Number of VOD files stored
~ 12 files
Alarm/Motion recording time
10 seconds each
Pre-Event Recording
3 seconds prior to PIR activation / alarm
Number of alarm/motion files that can be saved on the
Micro SD card
~40 files
PIR and video linked files
The file naming conventions link the PIR file with its corresponding video file
Detection speed
0.2 m/s to 2.5 m/s (0.6 ft/s to 11.5 ft/s)
Angle of view (Camera)
62.7° (V) x 91.4° (H) x 121.4° (D)
Video Image Resolution
1280 x 720 pixels
Facial Identification
4.5 meters
Facial Recognition
7 meters
Streaming Video
360p H.264 10 FPS
Audio
16 bit, 16KHz sampling rate, 32Kb/s mono
Physical Size
(H x W x D)15 cm x 7.5 cm x 5 cm (6 in x 3 in x 2 in)
Environmental
See the Paradox.com website for the latest certifications for this product.
Operating temperature
-10° C to +55° C (14° F to 131° F)
32
HD77 Installation Guide
Appendix: B
PIR Detector Beam Pattern
The beam pattern for the Detector is shown below.
Side view
Top view
(40)
4
2
(5.6)
(13)
2.1m
(6'8")
(26)
(40)
Feet
(30 )
(20)
(10 )
Feet
(10)
(20)
(30 )
(40)
(13)
12.0
10.0
(30 )
(6'6")
8.0
Feet
0
2
4
(40)
6
8
10
12
14
Meters
Meters
6.0
(20)
4.0
(10 )
2.0
100
degrees
12.0 10.0 8.0
6.0
4.0
2.0
Meters
2.0
4.0
6.0
8.0
10.0 12.0
Figure 38 – PIR Detector Beam Pattern
Note:
EN 50131 testing has been performed for 100 degrees
HD77 Installation Guide
33
Appendix: C
Certifications
Table 5:
Mark/
Area/Country
level/Grade/Class
European Economic Area (EEA)
34
European Economic Area (EEA)
WEEE
European Economic Area (EEA)
EN 50131-2-2 Grade 2
Environmental Class II
HD77 Installation Guide
HD77 Installation Guide
35
The whole Paradox team wishes you a successful and easy installation.
We hope this product performs to your complete satisfaction.
Should you have any questions or comments, please contact us.
For support, please contact your local distributor, or dial 1-800-791-1919
(in North America) or +1-450-491-7444 (outside North America), Monday
to Friday, from 8:00 a.m. to 8:00 p.m. EST.
You may also e-mail us at [email protected].
Additional information can be found at PARADOX.COM
Printed in Canada
HD77-EI00
paradox.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement