advertisement
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page a (1,1)
INSTRUCTION MANUAL
VHF MARINE TRANSCEIVER
iM503
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page b (1,1) i
IN CASE OF EMERGENCY
If your vessel requires assistance, contact other vessels and the Coast Guard by sending a distress call on Channel 16.
USING CHANNEL 16
DISTRESS CALL PROCEDURE
1. “MAYDAY MAYDAY MAYDAY.”
2. “THIS IS ...............” (name of vessel)
3. Your call sign or other indication of the vessel (AND 9-digit DSC ID if you have one).
4. “LOCATED AT ...............” (your position)
5. The nature of the distress and assistance required.
6. Any other information which might facilitate the rescue.
Or, transmit your distress call using digital selective calling on
Channel 70 (the optional DS-100 (#02) must be installed).
USING DIGITAL SELECTIVE CALLING
(Ch 70)
(DS-100 (#02) DSC CONTROLLER is required)
DISTRESS CALL PROCEDURE
1. Push and hold [DISTRESS] on the DS-100 for 5 sec. until you hear 5 short beeps change to one long beep.
2. Wait for an acknowledgment from a coast station.
• Channel 16 is automatically selected.
3. Push and hold [PTT], then transmit the appropriate information as at left.
Versions of the IC-M503 which display the “CE” symbol on the serial number seal, comply with the essential requirements of the
European Radio and Telecommunication Terminal Directive
1999/5/EC.
This warning symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use. Be sure to check that you have the correct version of this radio or the correct programming of this radio, to comply with national licensing requirements.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page c (1,1)
TABLE OF CONTENTS
IN CASE OF EMERGENCY ........................i
TABLE OF CONTENTS ..............................ii
IMPORTANT ..............................................iii
CAUTIONS.................................................iii
1 OPERATING RULES .......................... 1
2 PANEL DESCRIPTION .................. 2 – 5
■ Panel description ............................. 2
■ Function display ............................... 4
■ Microphone ...................................... 5
3 BASIC OPERATION .................... 6 – 10
■ Channel selection ............................ 6
■ Receiving and transmitting .............. 8
■ Call channel programming ............... 9
■ Channel names ................................ 9
■ Optional voice scrambler operation .. 10
4 DUALWATCH/TRI-WATCH ............... 11
■ Description ..................................... 11
■ Operation ....................................... 11
5 SCAN OPERATIONS ................. 12 – 13
■ Scan types ..................................... 12
■ Setting tag channels ...................... 13
■ Starting a scan ............................... 13
6 SET MODE ................................. 14 – 16
■ Set mode programming ................. 14
■ Set mode items .............................. 15
7 INTERCOM OPERATION ................. 17
■ Intercom operation ......................... 17
8 CONNECTIONS AND
MAINTENANCE ......................... 18 – 24
■ Unpacking ...................................... 18
■ Antenna ......................................... 18
■ Fuse replacement .......................... 18
■ Cleaning ......................................... 18
■ Connections ................................... 19
■ Microphone hanger ........................ 20
■ Mounting the transceiver ............... 21
■ Optional unit installation ................. 23
■ Dimensions ..................................... 24
9 TROUBLESHOOTING ...................... 25
10 CHANNEL LIST ................................ 26
11 SPECIFICATIONS AND OPTIONS ... 27
■ Specifications ................................. 27
■ Options .......................................... 27
12 HM-134 REMOTE-CONTROL
MICROPHONE ........................... 28-38
■ Panel description ........................... 28
■ Function display ............................. 30
■ Channel selection .......................... 32
■ Receiving and transmitting ............ 33
■ Lock functions ................................ 34
■ Display backlighting ....................... 34
■ Monitor function ............................. 34
■ Call channel programming ............. 35
■ Optional voice scrambler operation......................................... 35
■ Starting a scan ............................... 36
■ Setting tag channels ...................... 36
■ Dualwatch/Tri-watch operation ...... 36
■ Set mode programming ................. 37
■ Intercom operation ......................... 38
■ Channel names .............................. 38
13 HM-134 CONNECTIONS AND
INSTALLATION ........................... 39-41
■ HM-134 supplied accessories .........39
■ Installation .......................................39
MB-75 TEMPLATE
INSTALLATION NOTES ii
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page d (1,1) iii
IMPORTANT
READ ALL INSTRUCTIONS
carefully and completely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL —
This instruction manual contains important operating instructions for the IC-M503.
CAUTIONS
RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock.
NEVER
connect the transceiver to a power source of more than 15.6 V DC or using reverse polarity. This will ruin the transceiver.
NEVER
cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver may be damaged.
NEVER
place the transceiver where normal operation of the vessel may be hindered or where it could cause bodily injury.
KEEP
the transceiver at least 1 m away from the ship’s navigation compass.
DO NOT
use or place the transceiver in areas with temperatures below –20°C or above +60°C or, in areas subject to direct sunlight, such as the cockpit.
AVOID
the use of chemical agents such as benzine or alcohol when cleaning, as they may damage the transceiver surfaces.
BE CAREFUL!
The transceiver rear panel will become hot when operating continuously for long periods.
BE CAREFUL!
The optional HM-134 remote-control microphone’s rear panel will become hot when monitoring continuously for long periods.
Place the transceiver in a secure place to avoid inadvertent use by children.
After exposure to salt water, clean the transceiver thoroughly with fresh water to avoid corrosion.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 1 (1,1)
• Read all rules and regulations pertaining to priorities and keep an up-to-date copy handy. Safety and distress calls take priority over all others.
• You must monitor Channel 16 when you are not operating on another channel.
• False or fraudulent distress signals are prohibited and punishable by law.
• Information overheard but not intended for you cannot lawfully be used in any way.
• Indecent or profane language is prohibited.
OPERATING RULES
1
(2) OPERATOR’S LICENSE
A Restricted Radiotelephone Operator Permit is the license most often held by small ship radio operators when a radio is not required for safety purposes.
The Restricted Radiotelephone Operator Permit must be posted or kept with the operator. Only a licensed radio operator may operate a transceiver.
However, non-licensed individuals may talk over a transceiver if a licensed operator starts, supervises, ends the call and makes the necessary log entries.
Keep a copy of the current government rules and regulations handy.
(1) SHIP STATION LICENSE
You must have a current radio station license before using the transceiver. It is unlawful to operate a ship station which is not licensed.
Inquire through your dealer or the appropriate government agency for a Ship-Radiotelephone license application. This government-issued license states the call sign which is your ship’s identification for radio purposes.
1
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 2 (1,1)
2
PANEL DESCRIPTION
■ Panel description
!1
!0
VHF MARINE iM503 o i
Function display
Speaker q
POWER
VOL
16
DUAL
WATER RESISTANT
SCAN
TAG
DIAL
HI/LO
SQL
CALL
DIMMER
2 w q POWER SWITCH [POWER]
Push to toggle the transceiver power ON and OFF.
w VOLUME CONTROL [VOL]
Adjusts the audio level. (p. 8) e SQUELCH CONTROL [SQL]
Sets the squelch threshold level. (p. 8) e r t y u r TRANSMIT POWER SWITCH [HI/LO]
➥Push to Toggle high and low power . (p. 8)
• Some channels are set to low power only.
➥While pushing and holding this switch, other switches perform secondary functions.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 3 (1,1)
PANEL DESCRIPTION
2 t CHANNEL SELECTOR [CHANNEL]
Rotate [CHANNEL] to select the operating channels, set mode contents, etc. (p. 8) y DIMMER SWITCH [DIMMER]
➥Push to select one of 8 backlighting (LCD and switches) levels.
➥Push and hold for 1 sec. to turn the intercom mode ON.
u CALL CHANNEL SWITCH [CALL]
➥Push to select the call channel. (p. 6)
➥Push and hold for 3 sec. to enter call channel programming condition. (p. 9)
➥While pushing and holding [HI/LO], enters memory name programming condition. (p. 9) i CHANNEL 16 SWITCH [16]
➥Push to select Channel 16. (p. 6)
➥While turning power ON, push to enter initial set mode.
(p. 14) o DIAL SWITCH [DIAL]
➥Push to exit from Channel 16 or call channel.
(p. 6)
➥While pushing and holding [HI/LO], push to select channel group. (pgs. 6, 7)
• The “EUR” version has International channels only and this function is not available.
!0 SCAN SWITCH [SCAN/TAG] (p. 13)
➥When tag channels are programmed, starts and stops normal or priority scan.
➥Push and hold [SCAN/TAG] for 1 sec. to set the displayed channel as a tag (scanned) channel.
➥While pushing and holding [HI/LO], push and hold for 3 sec. to clear all tag channels.
!1 DUALWATCH/TRI-WATCH SWITCH [DUAL] (p. 11)
➥Push to start dualwatch or tri-watch.
➥When dualwatch/tri-watch is activated, push to stop them.
3
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 4 (1,1)
4
2
PANEL DESCRIPTION
■ Function display
q w e r
BUSY
o i
INT
25W CALL
TAG SC DUP
CALLING
t y u q BUSY/TRANSMIT INDICATOR (p. 8)
➥“BUSY” appears when receiving a signal or when the squelch opens.
➥“TX” appears while transmitting.
w POWER INDICATOR (p. 8)
➥“25W” appears when high power is selected.
➥“1W” appears when low power is selected.
e TAG CHANNEL INDICATOR (p. 13)
Appears when a tag channel is selected.
r CHANNEL NAME INDICATOR
➥Channel comment appears if programmed. (p. 9)
➥“Low Battery” appears when the battery voltage drops to approx. 10 V DC or below.
➥“DUAL” appears during dualwatch; “TRI” appears during tri-watch. (p. 11)
➥“WAIT” appears in the IC-M503 display while transmitting via the HM-134 remote-control microphone.
• In the above case, the connected HM-134 has priority.
➥“LSTN” appears in the IC-M503 display when pushing the PTT switch on the HM-134, while the intercom function is activated.
t SCRAMBLER INDICATOR (p. 10)
Appears when the optional voice scrambler is activated.
y DUPLEX INDICATOR
Appears when a duplex channel is selected.
u CHANNEL NUMBER READOUT
➥Indicates the selected operating channel number. “A” appears when a simplex channel is selected. (p. 6)
➥In set mode, indicates the selected condition. (pgs.
15,16) i CHANNEL GROUP INDICATOR (p. 6)
Indicates whether an International, U.S.A., Holland, DSC or ATIS channel is selected.
• Available channel groups depend on version.
o CALL CHANNEL INDICATOR (pgs. 6, 9)
Appears when a call channel is selected.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 5 (1,1)
■ Microphone
q w
Speaker
Microphone e q PTT SWITCH [PTT]
Push and hold to transmit; release to receive. (p. 8)
Push either switch to change the operating memory channel, set mode contents, etc. (p. 8) e TRANSMIT POWER SWITCH [HI/LO]
➥Same as the [HI/LO] switch on the front panel.
➥When pushed at power ON, toggles the [Y]/[Z] and
[HI/LO] switch functions ON and OFF.
PANEL DESCRIPTION
2
5
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 6 (1,1)
6
3
BASIC OPERATION
■ Channel selection
Channel 16 is the distress and safety channel. It is used for establishing initial contact with another station and for emergency communications. Channel 16 is monitored during both dualwatch and tri-watch. While standing by, you must monitor
Channel 16.
➥Push [16] to select Channel 16.
• Output power turns to “25W” automatically, whenever Channel
16 is selected. For example, when selecting Channel 16 via the dial, a scan stops at Channel 16 or [16•C] on the HM-134 is pushed, etc.
➥Push [DIAL] to return to the condition before selecting Channel 16, or rotate [CHANNEL] to select operating channel.
• Output power returns to the previous output power automatically.
INT
Push 16
25W
TAG
CALLING
Each regular channel group has a separate leisure-use call channel. The call channel is monitored during tri-watch. The call channels can be programmed (p. 9) and are used to store your most often used channels in each channel group for quick recall.
➥Push [CALL] to select the call channel of the selected channel group.
• “CALL” and call channel number appear.
➥Push [DIAL] to return to the condition before selecting call channel , or rotate [CHANNEL] to select operating channel.
Push CALL
25W
TAG
CALLING
INT
CALL
There are 57 International channels for the IC-M503.
q Push [DIAL] to select a regular channel.
w While pushing and holding [HI/LO], push [DIAL]to change the channel group, if necessary.
• “INT” appears when International channels are selected.
e Rotate the channel selector to select a channel.
• “DUP” appears for duplex channels.
25W
TAG
INTL
INT
DUP
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 7 (1,1)
BASIC OPERATION
3
ï (U.K. version only)
For the U.K. versions, there are 58 U.S.A. channels in addition to 57 International channels.
q Push [DIAL] to select a regular channel.
w While pushing and holding [HI/LO], push [DIAL] to change the channel group.
• International and U.S.A. channels can be selected in sequence.
e Rotate the channel selector to select a channel.
• Channels are memorized separately for each channel group.
USA
25W
TAG
CCG
ï
(Holland version only)
For Holland versions, there are 59 Holland channels in addition to 57 International channels.
q Push [DIAL] to select a regular channel.
w While pushing and holding [HI/LO], push [DIAL] to change the channel group.
• International and Holland channels can be selected in sequence.
e Rotate the channel selector to select a channel.
• Channels are memorized separately for each channel group.
1W
INTL
HOLLAND
DUP
ï
(FRG version only)
For the FRG versions, there are 57 ATIS and 57 DSC channels in addition to 57 International channels.
q Push [DIAL] to select a regular channel.
w While pushing and holding [HI/LO], push [DIAL] to change the channel group.
• International, ATIS and DSC channels can be selected in sequence.
e Rotate the channel selector to select a channel.
• Channels are memorized separately for each channel group.
ATIS
25W
TAG
INTL
DUP
7
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 8 (1,1)
8
3
BASIC OPERATION
■ Receiving and transmitting
CAUTION:
Transmitting without an antenna may damage the transceiver.
q Push [POWER] to turn power ON.
w Set the audio and squelch levels.
➥Rotate [SQL] fully counterclockwise in advance.
➥Rotate [VOL] to adjust the audio output level.
➥Rotate [SQL] clockwise until the noise disappears.
e While pushing and holding [HI/LO], push [DIAL] to change the channel group. (p. 6)
• The European version has International channels only.
r Rotate the channel selector or push [Y]/[Z] on the microphone to select the desired channel.
• When receiving a signal, “BUSY” appears and audio is emitted from the speaker.
• Further adjustment of [VOL] may be necessary at this point.
• Use the optional voice scrambler function for privacy. (p. 10) t Push [HI/LO] to select the output power if necessary.
• “25W” or “1W” appears when high or low power is selected, respectively.
• Choose low power to conserve power, choose high power for longer distance communications.
• Some channels are for low power only.
y Push and hold [PTT] to transmit, then speak into the microphone.
• “TX” appears.
• Channel 70 cannot be used for transmission (for GMDSS use).
u Release [PTT] to receive.
IMPORTANT: To maximize the readability of your transmitted signal, pause a few sec. after pushing [PTT], hold the microphone 2 to 5 cm from your mouth and speak at a normal voice level.
q t e
VHF MARINE iM503
POWER
VOL
16
DUAL
WATER RESISTANT
SCAN
TAG
DIAL
HI/LO
SQL
CALL
DIMMER y u w r r t
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 9 (1,1)
■ Call channel programming
The call channel switch can be programmed to your most often-used channels in each channel group for quick recall.
q While pushing and holding [HI/LO], push [DIAL] one or more times to select the desired channel group (International, U.S.A., Holland, ATIS, DSC) to be programmed.
w Push and hold [CALL] for 3 sec. to enter the call channel programming condition.
• Channel number starts flashing.
25W
TAG
CALLING
INT
CALL e Rotate the channel selector to select the desired channel.
25W
TAG
INTL
INT
CALL
DUP r Push [CALL] to program the displayed channel as the call channel.
• Push [DIAL] to cancel the programming.
• The channel number stops flashing.
BASIC OPERATION
3
■ Channel names
Memory channels can be tagged with alphanumeric names of up to 10 characters each.
Capital letters, small letters, numerals, some symbols (! " # $
% & ' ( ) ✱ + , – . ⁄) and spaces can be used.
q Select the desired memory channel.
• Cancel dual watch, tri-watch or scan in advance.
w While pushing and holding [HI/LO], push [CALL] to edit the memory channel name.
• A cursor appears and blinks.
25W
TAG
äLEASURE
INT e Select the desired character by rotating the channel selector or by pushing [Y]/[Z] on the microphone.
• Push and hold [SCAN] or [DIAL] for cursor movement.
r Push [CALL] to input and set the name.
• The cursor disappears.
t Repeat steps q to r to program another memory channel name, if desired.
9
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 10 (1,1)
10
3
BASIC OPERATION
■ Optional voice scrambler operation
The optional voice scrambler provides private communications. In order to receive or send scrambled transmissions you must first activate the scrambler function. To activate the function, an optional UT-98 or UT-112 is necessary. See p. 16 for selecting the unit. Ask your dealer for details.
q Select an operating channel other than Channel 16 and
70.
w While pushing and holding [HI/LO], push [DIMMER] to toggle an optional scrambler function ON or OFF.
• “SC” appears.
e To turn the scrambler function OFF, repeat step w.
• “SC” disappears.
There are 128 or 32 codes (0 to 127 or 1 to 32) available for programming. In order to understand one another, all transceivers in your group must have the same scramble code.
This function may not be available depending on dealer setting.
q Turn power OFF.
w While pushing and holding [16], turn power ON to enter set mode.
e After the display appears, release [16].
r Push [16] one or more times to select the scrambler code item.
• “Scrambler code” appears.
t Rotate the channel selector to select the desired scrambler code.
y Turn power OFF, then ON again to exit set mode.
[Example]: Programming scrambler code 127.
16 + POWER
Enter set mode
Set mode
Beep
Set mode
16
Push one or more times.
Set mode
Scrambler code
Scrambler code item
Select code
Set mode
Scrambler code
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 11 (1,1)
■ Description
Dualwatch monitors Channel 16 while you are receiving another channel; tri-watch monitors Channel 16 and the call channel while receiving another channel.
DUALWATCH/TRI-WATCH SIMULATION
Dualwatch
Call channel
Tri-watch
• If a signal is received on Channel 16, dualwatch/tri-watch pauses on Channel 16 until the signal disappears.
• If a signal is received on the call channel during tri-watch, triwatch becomes dualwatch until the signal disappears.
• To transmit on the selected channel during dualwatch/tri-watch, push and hold [PTT].
DUALWATCH/TRI-WATCH
4
■ Operation
q Select the desired operating channel.
w Select dualwatch or tri-watch in set mode. (p. 15) e Push [DUAL] to start dualwatch or tri-watch.
• “DUAL” appears during dualwatch; “TRI” appears during triwatch.
• Beep tone sounds when a signal is received on Channel 16.
• Tri-watch becomes dualwatch when receiving a signal on the call channel.
r To cancel dualwatch/tri-watch, push [DUAL] again.
[Example]: Operating tri-watch on INT Channel 25.
INT
Tri-watch starts.
25W
TAG
TRI
DUP
16
BUSY
25W
TAG
CALLING
INT
CALL
16
Signal is received on call channel.
BUSY
25W
TAG
CALLING
INT
DUP
16
25W
TAG
TRI
INT
DUP
16
Signal received on
Channel 16 takes priority.
Tri-watch resumes after the signal disappears.
11
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 12 (1,1)
12
5
SCAN OPERATIONS
■ Scan types
Scanning is an efficient way to locate signals quickly over a wide frequency range. The transceiver has priority scan and normal scan.
PRIORITY SCAN
CH 01 CH 02
Set the tag channels (scanned channel) before scanning.
Clear the tag channels which inconveniently stop scanning, such as those for digital communication use.
Choose priority scan or normal scan in set mode in advance. (p. 15)
NORMAL SCAN
CH 01 CH 02
CH 06 CH 06 CH 16 CH 03
CH 05 CH 04
Priority scan searches through all tag channels in sequence while monitoring Channel 16. When a signal is detected on Channel 16, scan pauses until the signal disappears; when a signal is detected on a channel other than
Channel 16, scan becomes dualwatch until the signal disappears.
CH 03
CH 05 CH 04
Normal scan, like priority scan, searches through all tag channels in sequence. However, unlike priority scan, Channel 16 is not checked unless Channel 16 is set as a tag channel.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 13 (1,1)
SCAN OPERATION
5
■ Setting tag channels
For more efficient scanning, add desired channels as tag channels or clear tag channels that are unwanted channels.
Channels set as non-tag channels will be skipped during scanning. Tag channels can be assigned to each channel group (International, U.S.A., Holland, DSC, ATIS) independently.
for 3 sec. to clear all tag channels in the channel group.
■ Starting a scan
Set scan type (priority or normal scan) and scan resume timer in advance using set mode. (p. 15) q While pushing and holding [HI/LO], push [DIAL] one or more times to select the desired channel group, if desired.
w Select the desired channel to set as a tag channel.
e Push and hold [SCAN/TAG] for 1 sec. to set the displayed channel as a tag channel.
• “TAG” appears in the function display.
r To cancel the tag channel setting, repeat e.
• “TAG” disappears.
• Clearing all tag channels in the selected channel group
➥While pushing and holding [HI/LO], push and hold [DIAL]
[Example]: Starting a normal scan.
25W
TAG
INTL
INT
DUP
Push
SCAN
TAG
INT
25W
TAG DUP
Normal scan q Set tag channels as described at left.
w While pushing and holding [HI/LO], push [DIAL] one or more times to select the desired channel group, if desired.
e Push [SCAN] to start priority or normal scan.
• “Pri scan 16” or “Normal scan” appears in the function display.
• When a signal is detected, scan pauses until the signal disappears or resumes after pausing 5 sec. according to set mode setting. (Channel 16 is still monitored during priority scan.)
• Rotate the channel selector to check the scanning tag channels, to change the scanning direction or resume the scan manually.
• “16” flashes and a beep tone sounds when a signal is received on Channel 16 during priority scan.
r To stop the scan, push [SCAN].
• “Pri scan” or “Normal scan” disappears.
Scan starts.
BUSY
25W
INT
TAG DUP
Normal scan
When a signal is received
13
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 14 (1,1)
14
6
SET MODE
■ Set mode programming
Set mode is used to change the conditions of the transceiver’s functions: scan mode (normal or priority), scan resume timer, dualwatch/tri-watch selection, beep tone function
(transceiver or HM-134), internal speaker (transceiver or HM-
134), LCD contrast (transceiver or HM-134), scrambler code, scrambler type and ATIS check.
• Available functions may differ depending on dealer setting.
• The optional HM-134 has it’s own settings for the beep tone, internal speaker and LCD contrast.
q Turn power OFF.
w While pushing and holding [16], turn power ON to enter set mode.
e After the display appears, release [16].
r Push [16] to select the desired item, if necessary.
t Rotate the channel selector to select the desired condition of the item.
y Turn power OFF, then ON again to exit set mode.
• SET MODE CONSTRUCTION
ATIS check
ATIS check
Scrambler type
Scrambler type
Scan mode
Scan mode
Scan resume timer
Scan timer
Push 16
Scrambler code
Scrambler code
LCD contrast
LCD contrast
Dual/tri watch
DUAL/TRI
Beep tone
Beep
Internal speaker
Internal speaker
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 15 (1,1)
SET MODE
6
■ Set mode items
The transceiver has 2 scan modes: normal scan and priority scan. Normal scan searches all tag channels in the selected channel group. Priority scan searches all tag channels in sequence while monitoring channel 16.
Set mode
Scan mode
Priority scan (default) Normal scan
This item sets the [DUAL] switch function as dual watch or triwatch.
See the section ‘Dual watch/Tri-watch’ for details.
Set mode
DUAL/TRI
Dual watch (default) Tri-watch
The scan resume timer can be selected as a pause (OFF) or timer scan (ON). When OFF is selected, the scan pauses until the signal disappears. When ON is selected, the scan pauses 5 sec. and resumes even if a signal is being received on channels, except for Channel 16.
Set mode
Scan timer
Scan timer ON (default) Scan timer OFF
You can select silent operation by turning beep tones OFF or you can have confirmation beeps sound at the push of a switch by turning beep* tones ON.
Set mode
Beep
Beep tone ON (default) Beep tone OFF
*Beep tones setting are selectable on IC-M503 and HM-134 independently
15
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 16 (1,1)
6
SET MODE
16
When an optional external speaker is connected, the speakers on the transceiver and microphone can be muted.
Set mode
Internal speaker
Internal speaker ON (default) Internal speaker OFF
*Internal speaker setting is selectable on IC-M503 and HM-134 independently
This item adjusts the contrast of the LCD in 8 steps.
Set mode
LCD contrast
LCD contrast 4 (default)
*LCD contrast setting is adjustable on IC-M503 and HM-134 independently
When an optional scrambler unit is connected, the scrambler code can be set depending on dealer setting.
When the UT-98 or UT-112 is installed, 128 or 32 codes (0 to
127 or 1 to 32) can be selected, respectively.
Set mode
Scrambler code
Scrambler code 0 (UT-98 default)
The ATIS ID code can be checked in set mode.
Set mode
ATIS check
0123456789
ATIS code
Scrambler code 127
When an optional scrambler unit is connected, the scrambler unit can be selected in set mode depending on dealer setting.
Set mode
Scrambler type
UT-98 scrambler unit UT-112 scrambler unit
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 17 (1,1)
INTERCOM OPERATION
7
■ Intercom operation
The optional intercom function allows you to talk to the deck from the cabin. The optional HM-134*
REMOTE
-
CONTROL MI
-
CROPHONE is required for intercom operation.
*DO NOT connect another remote-control microphone.
Connect an optional HM-134 as described on p. 39.
• Transmitting is impossible during intercom operation.
• The received signal is muted during intercom operation.
q Push and holding [DIMMER] for 1 sec. to enter intercom mode.
• The HM-134 power is automatically turned ON, even if the power is OFF.
Intercom
INT
INT
IC-M503 HM-134 w Push and hold [DIMMER] again to call up.
• The transceiver and microphone emit call beeps.
e Push and hold the PTT switch and speak at a normal voice level into the microphone.
• “TALK” or “LSTN” appears on the caller or listener function display, respectively.
• To adjust the IC-M503’s speaker output level, rotate [VOL].
• To adjust the HM-134’s speaker output level, push [Y]/[Z] after pushing [VOL].
INT
INT
Intercom
TALK
IC-M503 (caller) HM-134 (listener) r After releasing the PTT switch you can hear the response through the speaker.
t To return to normal operation, push [DIMMER] momentarily.
• Other switches also turn the function OFF, however, the corresponding function is then activated e.g. pushing [16] selects
Channel 16.
• While in the intercom mode, the transceiver functions
(transmit and receive) are interrupted. If the transceiver is in transmit condition, the intercom function is not available.
17
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 18 (1,1)
18
8
CONNECTIONS AND MAINTENANCE
■ Unpacking
The following accessories are supplied: Qty.
q Mounting bracket ............................................................ 1 w DC power cable (OPC-891) ........................................... 1 e Microphone hanger ........................................................ 1 r Microphone hanger cable*
(OPC-1096 : Black) ........................................................ 1 t Mounting bracket knobs ................................................. 2 y Microphone hanger screws (3 × 16 mm
) ......................... 2 u Mounting screws (5 × 20 mm ) ......................................... 2 i Flat washers (M5) ........................................................... 2 o Spring washers (M5) ...................................................... 2
* Depending on version.
■ Antenna
A key element in the performance of any communication system is an antenna. Ask your dealer about antennas and the best places to mount them.
■ Fuse replacement
Two fuses are installed in the supplied DC power cable. If a fuse blows or the transceiver stops functioning, track down the source of the problem, if possible, and replace the damaged fuse with a new, rated one.
q e t y
■ Cleaning
If the transceiver becomes dusty or dirty, wipe it clean with a soft, dry cloth.
AVOID the use of solvents such as benzene or alcohol, as they may damage transceiver surfaces.
u i o w r
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 19 (1,1)
■ Connections
q w t r e q DC POWER CONNECTOR
Connects the supplied DC power cable from this connector to an external 12 V DC power source.
CAUTION:
After connecting the DC power cable and external speaker jack, cover the connector and jack as shown below to avoid water seeping into the transceiver.
CONNECTIONS AND MAINTENANCE
8 w EXTENSION JACK
Connects to the optional DS-100 (#02) DSC CONTROLLER .
e EXTERNAL MICROPHONE CONNECTOR
Connects to the optional HM-134
REMOTE
-
CONTROL MICRO
-
PHONE
.
• Intercom function is available.
CAUTION: NEVER
connect another microphone such as the HM-127, etc. It may cause damage to the transceiver.
r ANTENNA CONNECTOR
Connects a marine VHF antenna with a PL-259 connector to the transceiver.
CAUTION :
Transmitting without an antenna may damage the transceiver.
t EXTERNAL SPEAKER JACK
Connects to an external speaker. See ‘Options’ on p. 27 for available external speakers.
19
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 20 (1,1)
8
CONNECTIONS AND MAINTENANCE
■ Microphone hanger
20
OPC-1096
Rest the supplied microphone on the hanger when not in use.
Connect the OPC-1096* to the transceivers chassis and microphone hanger to use the microphone hanger function.
* Depending on version.
• Tighten the screw at fixing torque 0.7 N •m (6.9 kg•m).
• If the microphone hanger function is used, Channel 16 is selected automatically when the supplied microphone is rested on the hanger.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 21 (1,1)
CONNECTIONS AND MAINTENANCE
8
• OVERHEAD MOUNTING
■ Mounting the transceiver
The universal mounting bracket supplied with your transceiver allows overhead or dashboard mounting.
• Mount the transceiver securely with the 2 screws supplied
(M5 × 20) to a surface which is more than 10 mm thick and can support more than 5 kg.
• Mount the transceiver so that the face of the transceiver is at
90° to your line of sight when operating it.
CAUTION:
KEEP the transceiver and microphone at least 1 meter away from your ship’s magnetic navigation compass.
NOTE: Check the installation angle; the function display may not be easy-to-read at some angles.
• MOUNTING ON DASHBOARD
21
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 22 (1,1)
22
8
CONNECTIONS AND MAINTENANCE
An optional MB-75 FLUSH MOUNT is available for mounting the transceiver to a flat surface such as an instrument panel.
CAUTION:
KEEP the transceiver and microphone at least 1 meter away from your ship’s magnetic navigation compass.
q Using the template on the last page, carefully cut a hole into the instrument panel (or wherever you plan to mount the controller).
w Slide the transceiver through the hole as shown below.
r Attach the clamps on either side of the transceiver.
• Make sure that the clamps align parallel to the transceiver body.
t Tighten the end bolts on the clamps (rotate clockwise) so that the clamps press firmly against the inside of the instrument control panel.
y Tighten the locking nuts (rotate counterclockwise) so that the transceiver is securely mounted in position as below.
u Connect the antenna and control cable, then return the instrument control panel to its original place.
e Attach the 2 bolts supplied (M5 × 8 mm) on either side of the IC-M503.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 23 (1,1)
CONNECTIONS AND MAINTENANCE
8
■ Optional unit installation
CAUTION:
DISCONNECT the DC power cable from the transceiver before performing any work on the transceiver.
Otherwise, there is danger of electric shock and/or equipment damage.
w Remove the 4 screws from the shielding plate, then lift up the shielding plate.
e Plug an optional unit to the MAIN unit as shown below.
Follow the case opening procedure shown here when you want to install an optional unit, etc.
q Remove the 6 screws as shown below and open the transceiver.
Optional unit r Return the shielding plate and assemble the units to their original positions.
23
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 24 (1,1)
8
CONNECTIONS AND MAINTENANCE
■ Dimensions
145.0 (5 23 ⁄
32
˝)
24
165.0 (6 1 ⁄ 2 ˝)
31.4
(1 1 / 4 ˝)
53.0
(2 3 / 32 ˝)
Unit: mm (inch)
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 25 (1,1)
TROUBLESHOOTING
9
PROBLEM
No power comes ON.
No sound comes from the speaker.
POSSIBLE CAUSE
• Bad connection to the power supply.
• Squelch level is too deep.
• Volume level is too low.
• Speaker has been exposed to water.
Transmitting is impossible, or high power can not be selected.
Scan does not start.
• Some channels are for low power or receive only.
er can
• The output power is set to low.
• “TAG” channel is not programmed.
No beep sounds.
Receive signal cannot be understood.
• Beep tone is turned OFF.
• Optional voice scrambler is turned OFF.
• Scramble code is not set correctly.
SOLUTION
• Check the connection to the transceiver.
• Set squelch to the threshold point.
• Set [VOL] to a suitable level.
• Drain water from the speaker.
• Change channels.
• Push [HI/LO] to select high power.
• Set the desired channels as “TAG” channels.
• Turn the beep tone ON in SET mode.
• Turn the optional voice scrambler ON.
• Reset the scramble code.
REF.
p. 19 p. 8 p. 8
— pgs.
6, 26 p. 8 p. 13 p. 15 p. 10 p. 16
25
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 26 (1,1)
26
10
CHANNEL LIST
• International channels
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
01 156.050
160.650
11 156.550
156.550
21 157.050
161.650
62 156.125
160.725
72 156.625
156.625
82 157.125
161.725
02 156.100
160.700
12 156.600
156.600
22 157.100
161.700
63 156.175
160.775
73 156.675
156.675
83 157.175
161.775
03 156.150
160.750
13 156.650
156.650
23 157.150
161.750
64 156.225
160.825
74 156.725
156.725
84 157.225
161.825
04 156.200
160.800
14 156.700
156.700
24 157.200
161.800
65 156.275
160.875
75 † 156.775
156.775
85 157.275
161.875
05 156.250
160.850
15 † 156.750
156.750
25 157.250
161.850
66 156.325
160.925
76 † 156.825
156.825
86 157.325
161.925
06 156.300
156.300
16 156.800
156.800
26 157.300
161.900
67 156.375
156.375
77 156.875
156.875
87 157.375
157.375
07 156.350
160.950
17 † 156.850
156.850
27 157.350
161.950
68 156.425
156.425
78 156.925
161.525
88 157.425
157.425
08 156.400
156.400
18 156.900
161.500
28 157.400
162.000
69 156.475
156.475
79 156.975
161.575
09 156.450
156.450
19 156.950
161.550
60 156.025
160.625
70 ‡ 156.525
156.525
80 157.025
161.625
10 156.500
156.500
20 157.000
161.600
61 156.075
160.675
71 156.575
156.575
81 157.075
161.675
• USA channels (for U.K. version only)
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
01A 156.050
156.050
12 156.600
156.600
22A 157.100
157.100
64A 156.225
156.225
77 156.875
156.875
86 157.325
161.925
-- - - - 13 † 156.650
156.650
23A 157.150
157.150
65A 156.275
156.275
78A 156.925
156.925
86A 157.325
157.325
03A 156.150
156.150
14 156.700
156.700
24 157.200
161.800
66A 156.325
156.325
79A 156.975
156.975
87 157.375
161.975
-- - - - 15 † 156.750
156.750
25 157.250
161.850
67 † 156.375
156.375
80A 157.025
157.025
87A 157.375
157.375
05A 156.250
156.250
16 156.800
156.800
26 157.300
161.900
68 156.425
156.425
81A 157.075
157.075
88 157.425
162.025
06 156.300
156.300
17 † 156.850
156.850
27 157.350
161.950
69 156.475
156.475
82A 157.125
157.125
88A 157.425
157.425
07A 156.350
156.350
18A 156.900
156.900
28 157.400
162.000
70 ‡ 156.525
156.525
83A 157.175
157.175
08 156.400
156.400
19A 156.950
156.950
37A 157.850
157.850
71 156.575
156.575
84 157.225
161.825
09 156.450
156.450
20 157.000
161.600
61A 156.075
156.075
72 156.625
156.625
84A 157.225
157.225
10 156.500
156.500
20A 157.000
157.000
-- - - - 73 156.675
156.675
85 157.275
161.875
11 156.550
156.550
21A 157.050
157.050
63A 156.175
156.175
74 156.725
156.725
85A 157.275
157.275
† Low power only.
‡ Receive only.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 27 (1,1)
SPECIFICATIONS AND OPTIONS
11
■ Specifications
• GENERAL
• Frequency coverage :
Transmit 156.000–161.450 MHz
Receive 156.000–163.425 MHz
• Mode : FM (16K0G3E)
• Channel spacing
• Current drain (at 13.8 V)
: 25 kHz
: TX high
Max. audio
6.0 A max.
1.5 A max.
• Power supply requirement : 13.8 V DC (10.8 to 15.6 V)
• Frequency stability : ±10 ppm (–20°C to +60°C)
• Dimensions : 165(W)
×110(H)×109.4(D) mm
(Projection not included)
• TRANSMITTER
• Output power
• Modulation system
: 25 W and 1 W
: Variable reactance phase modulation
• Max. frequency deviation : ±5.0 kHz
• Spurious emissions : Less than 0.25 µW
• RECEIVER
• Receive system : Double conversion superheterodyne
• Sensitivity (20 dB SINAD) : Less than –3dBµ EMF (typical)
• Squelch sensitivity : Less than 0dBµ EMF
• Intermodulation rejection ratio : More than 68 dB
• Spurious response rejection ratio: More than 70 dB
• Adjacent channel selectivity : More than 70 dB
• Audio output power
IC-M503
HM-134
:
2 W at 10% distortion with a 4
Ω load
2 W at 10% distortion with a 8
Ω load
■ Options
• DS-100 (#02)
DSC CONTROLLER
When the DS-100 is installed, the transceiver conforms to
DSC Class D for marine digital communications.
• MB-75
FLUSH MOUNT
For mounting the transceiver to a panel.
• HM-134
REMOTE
-
CONTROL MICROPHONE
External microphone-type controller. Provides optional intercom operation. 6 m (20 feet) microphone cable and mounting base included. Black color is available.
• OPC-999
MICROPHONE EXTENSION CABLE
6 m (20 feet) microphone extension cable for optional
HM-134. Up to 2 OPC-999 can be connected. (18 m; 60 feet maximum)
• SP-5
EXTERNAL SPEAKER
(IC-M503
ONLY
)
A large, external speaker for superior audio output.
• SP-10
EXTERNAL SPEAKER
(IC-M503
ONLY
)
A compact, external speaker. Features easy installation.
• UT-98
VOICE SCRAMBLER UNIT
• UT-112
VOICE SCRAMBLER UNIT
Ensures private communications. 128 or 32 codes are available. Not available in some countries.
All stated specifications are subject to change without notice or obligation.
27
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 28 (1,1)
28
12
HM-134 REMOTE-CONTROL MICROPHONE
■ Panel description
The optional HM-134 remotely controls the IC-M503 and provides an optional intercom function.
q
!0
o w e r
!1
C
DIM
VOL
MONI L
SQL
DIAL
IC
DUAL i u y t
OPTIONAL
q POWER SWITCH [PWR] (pgs. 8, 33)
When the IC-M503 power is turned ON, push and hold for
2 sec. to turn the HM-134 power ON or OFF.
w PTT SWITCH [PTT] (pgs. 8, 33)
Push and hold to transmit; release to receive.
e CHANNEL UP/DOWN SWITCHES [Y
➥Push either switch to change the operating channel, set mode contents, etc. (pgs. 8, 33)
➥While pushing and holding [VOL], push [Y]/[Z] to adjust the brightness of the LCD and switch backlight. (p. 34)
➥After [VOL] or [SQL] is pushed, push either switch to adjust audio level or noise squelch level, respectively. (pgs.
8, 33)
➥In set mode, changes setting of the selected item. (pgs.
9, 37)
➥During scanning, checks tag channels or changes scanning direction. (pgs. 8, 36) r CHANNEL 16/CALL CHANNEL SWITCH [16•C]
➥When pushed, selects Channel 16. (pgs. 6, 32)
➥When pushed and held for 1 sec., selects call channel.
(pgs. 6, 32)
• “CALL” appears when call channel is selected.
➥When call channel is selected, push and hold for 3 sec.
to enter call channel programming condition. (pgs. 9, 35)
➥While pushing and holding [H/L], enters memory name programming condition. (pgs. 9, 38)
To IC-M503
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 29 (1,1)
➥Enter set mode when pushed and held while turning power ON. (pgs. 14, 37) t DIAL SWITCH [DIAL]
➥Selects and toggles the regular channels when pushed momentarily. (pgs. 6, 7, 32)
➥While pushing and holding [H/L], push to select channel group. (pgs. 6, 7 and 32)
• The “ EUR” version has International channels only and this function is not available.
y DUAL-WATCH/INTERCOM SWITCH [DUAL•IC]
➥Push to start dualwatch or tri-watch. (pgs. 11, 36)
➥Push and hold for 1 sec. to activate the intercom function. (pgs. 17, 38)
➥Push to stop dualwatch or tri-watch when either is activated.
➥While pushing and holding the switch, you can call the
IC-M503 in intercom mode. (pgs. 17, 38) u SQUELCH/MONITOR/LOCK SWITCH [SQL•MONI•L]
➥After pushing [SQL], [Y]/[Z] sets the squelch threshold level. (p. 33)
➥Push and hold [SQL•MONI] for 1 sec. to turn the monitor function ON. (p. 34)
➥While pushing and holding [H/L], push [SQL•MONI•L] to toggle the microphone key lock function ON or OFF. (p.
34)
• “ T ” appears while key lock function is in use.
• [PWR], [PTT], [VOL], [SQL] and [H/L] still function when the
HM-134 REMOTE-CONTROL MICROPHONE
12 microphone key lock function is turned ON.
➥Advances the cursor while in memory name programming condition. (pgs. 9, 38) i VOLUME/DIMMER SWITCH [VOL•DIM]
➥After pushing [VOL], [Y]/[Z] adjusts the audio level.
➥Push and hold [VOL•DIM] for 1 sec. to adjust the brightness of the LCD and switch backlight. (p. 34)
➥Moves the cursor backward while in memory name programming condition. (pgs. 9, 38) o TRANSMIT POWER SWITCH [H/L]
➥When pushed, toggles high and low power. (pgs. 8, 33)
• Some channels are set to low power only.
➥While pushing and holding this switch, other switches perform secondary functions.
➥Toggles the all key lock function ON or OFF when pushed and held while turning power ON. (p. 34)
• “ T ” flashes while the all key lock function is in use.
• Only [PWR] and [PTT] function when the all key lock function is in use.
!0 SCAN SWITCH [SCAN•TAG] (pgs. 13, 36)
➥Starts and stops normal or priority scan when tag channels are programmed.
➥Push and hold [SCAN•TAG] for 1 sec. to set the displayed channel as a tag (scanned) channel.
➥While pushing and holding [H/L], push and hold for 3 sec. to clear all tag channels.
29
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 30 (1,1)
30
12
HM-134 REMOTE-CONTROL MICROPHONE
!1 EXTERNAL SPEAKER JACK
➥Connect the external speaker ( an 8 Ω load) . The internal speaker can be deactivated via the Set mode programming. (p. 37)
• The speaker output employs a BTL (Balanced Trans-
Less) circuit, NEVER connect the speaker cable to ground (or chassis). Use a floating setup.
CAUTION:
After connecting the external speaker jack, cover the jack with water resistant tape as shown below to avoid water seeping into the microphone.
Binding the mic-cable and external-speaker jack connection mold with water resistant tape increases the waterproofing of the connection mold.
External SP jack
Connection mold
■ Function display
!7
!6 !5
!4
!3
!2
!1
q w e r t
WAIT TX BUSY TAG CALL LOW
USA
INT
L
DUP DUAL
P SCAN TRI
VOL
SQL
SCRM
!0
o i u y q CHANNEL GROUP INDICATOR (pgs. 6, 32)
Indicates whether an International (INT) or U.S.A. (USA) channel is selected.
w KEY LOCK INDICATOR (p. 34)
➥Appears while the key lock function is in use.
➥Flashes while the all key lock function is in use.
e CHANNEL NUMBER READOUT
➥Indicates the selected operating channel number. “A” appears when a simplex channel is selected. (pgs. 6,
32)
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 31 (1,1)
➥In set mode, indicates the selected condition. (pgs. 14,
37) r VOLUME INDICATOR (p. 33)
Appears while audio output level is adjusted.
t SQUELCH INDICATOR (p. 33)
Appears while noise squelch level is adjusted.
y CHANNEL NAME INDICATOR
➥Channel comment appears (and scrolls) if programmed.
(pgs. 9, 38)
➥In set mode, indicates or scrolls the selected set mode item. (pgs. 14, 37) u SCRAMBLER INDICATOR (pgs. 10, 35)
Appears when an optional voice scrambler is activated.
i SCAN INDICATOR (pgs. 13, 36)
➥“SCAN” appears during normal scan.
➥“P SCAN” appears during priority scan.
o PRIORITY CHANNEL INDICATOR
➥Indicates a priority channel during priority scan or dual/tri-watch. (pgs. 12, 36)
➥“IC” appears during intercom mode. (pgs. 17, 38)
!0 DUAL/TRI WATCH INDICATOR (pgs. 11, 36)
“DUAL” appears during dualwatch; “TRI” during tri-watch.
!1 LOW POWER INDICATOR (pgs. 8, 33)
HM-134 REMOTE-CONTROL MICROPHONE
12
Appears when low power is selected.
!2 CALL CHANNEL INDICATOR (pgs. 6, 32)
Appears when the call channel is selected.
!3 DUPLEX INDICATOR (pgs. 6, 32)
Appears when a duplex channel is selected.
!4 TAG CHANNEL INDICATOR (pgs. 13, 36)
Appears when a tag channel is selected.
!5 BUSY INDICATOR (pgs. 8, 33, 34)
Appears when receiving a signal or when the squelch opens.
!6 TRANSMIT INDICATOR (pgs. 8, 33)
Appears while transmitting.
!7 “WAIT” INDICATOR
“WAIT” appears in the HM-134 display while transmitting via the IC-M503’s attached microphone.
• In the above case, the connected HM-134 does not have priority.
31
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 32 (1,1)
32
12
HM-134 REMOTE-CONTROL MICROPHONE
■ Channel selection
q Push [16•C] to select Channel
16.
w Push [DIAL] to return to the condition before selecting Channel
16, or push [Y] or [Z] to select operating channel.
• Output power turns to “25W” automatically, whenever Channel 16 is selected. q Push [DIAL] to select regular channel.
w While pushing and holding [H/L], push [DIAL] to select channel group.
• U.S.A. or International can be selected in sequence.
q Push and hold [16•C] for 1 sec.
to select call channel.
w Push [DIAL] to return to the condition before selecting call channel, or push [Y] or [Z] to select operating channel.
U.S.A. channels
Push and hold then push
DIAL
International channels
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 33 (1,1)
HM-134 REMOTE-CONTROL MICROPHONE
12
■ Receiving and transmitting
q Push [PWR] to turn power ON.
w Push [VOL], then [Y]/[Z] to adjust audio output level.
• Push [SQL], then [Y]/[Z] to mute any audio noise, if necessary.
e Push [Y]/[Z] to select the desired channel.
• When receiving a signal, “ from the speaker.
” appears and audio is emitted
• Further adjustment of audio level may be necessary at this point.
• Use the optional voice scrambler function for privacy. (pgs. 10,
35) r Push [H/L] to select the output power, if necessary.
• “LOW” appears when low power is selected.
• Choose low power for shorter, high power for longer distance communications.
• Some channels are low power only.
q Turn power ON r Set output power t Push and hold [PTT] to transmit, then speak into the microphone.
• “ ” appears.
• Channel 70 cannot be used for transmission (for GMDSS use).
y Release [PTT] to receive.
IMPORTANT: To maximize the readability of your transmitted signal (voice), pause a few sec. after pushing [PTT], hold the microphone 10 to 15 cm (4 to 6 inches) from your mouth and speak at a normal voice level.
t Push to
transmit y Release
to receive e Set channel w Set volume w Set squelch,
if required t Speak into
microphone
33
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 34 (1,1)
34
12
HM-134 REMOTE-CONTROL MICROPHONE
■ Lock functions
The lock function electronically locks keys and switches to prevent accidental changes and function access from the microphone.
• All keys, switches and controllers on the transceiver are functional.
function
➥While pushing and holding
[H/L], push [SQL] to turn the lock function ON and OFF.
• “ ” appears.
• Only [PWR], [PTT], [H/L],
[SQL•MONI], [VOL]+[Y]/[Z] and
[SQL]+[Y]/[Z] are functional.
Appears when the lock function is in use.
■ Display backlighting
The function display and switches can be backlit for better visibility under low light conditions. And the backlighting condition can be adjusted independently from the transceiver.
q Push and hold [VOL•DIM] for 1 sec. to enter backlight adjusting mode.
• “ ” with number of backlight level appears in the channel name indicator.
w Push [Y]/[Z] to adjust the backlight level.
• The backlight level is adjustable between 0 (lights OFF) and 3
(brightest).
lock function
➥While pushing and holding
[H/L], turn the power ON by pushing [PWR] to turn the all key lock function ON and OFF.
• “ ” flashes.
• Only [PWR] and [PTT] are functional.
Flashes when the all lock function is in use.
■ Monitor function
The monitor function releases the noise squelch mute of the microphone only. (An independent noise squelch system is employed.)
➥Push and hold [SQL•MONI] for 1 sec. to activate the monitor function.
• “ ” flashes and audio is emitted.
• Any key, except [Y]/[Z], cancels the monitor function.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 35 (1,1)
■ Call channel programming
q While pushing and holding [H/L], push [DIAL] several times to select the desired channel group (USA or
INT) to be programmed.
w Push and hold [16•C] for 1 sec. to select the call channel of the selected channel group.
• “CALL” and call channel number appear.
e Push and hold [16•C] again for
3 sec. (until long beep changes to
2 short beeps) to enter call channel programming condition.
• Call channel number and channel group to be programmed flashes.
r Push [Y]/[Z] to select the desired channel.
t Push [16•C] to program the displayed channel as the call channel.
• The call channel number and channel group stop flashing.
HM-134 REMOTE-CONTROL MICROPHONE
12
■ Optional voice scrambler operation
q Select an operating channel, other than Channel 16.
w While pushing and holding
[H/L], push [DUAL] to turn the voice scrambler function
ON.
• “SCRM” appears.
e To turn the scrambler function OFF, repeat step w.
• “SCRM” disappears.
Appears when the voice scrambler function is in use.
There are 128 codes (00 to 127) available with UT-98 or 32 codes (01 to 32) available with the UT-112 for programming.
In order to understand one another, all transceivers in your group must have the same scrambler code, as well as the same scrambler unit. The scrambler code is programmed in set mode. See pgs. 10, 16, 37 for details.
35
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 36 (1,1)
36
12
HM-134 REMOTE-CONTROL MICROPHONE
■ Starting a scan
q While pushing and holding [H/L], push [DIAL] several times to select the channel group (USA or INT), if desired.
w Push [SCAN] to start priority or normal scan.
• “SCAN” appears during normal scan.
• The priority channel readout indicates
“16”, and “P” and “SCAN” indicators appear during priority scan.
• When a signal is received, scan pauses until the signal disappears or resumes after pausing 5 sec. according to set mode setting (Channel 16 is still monitored during priority scan).
• Push [Y]/[Z] to check the scanning tag channels, to change the scanning direction or resume the scan manually.
e To stop the scan, push [SCAN].
• “SCAN” disappears.
• Pushing [PTT], [16•C] or [DIAL] also stops the scan.
■ Setting tag channels
q While pushing and holding [H/L], push [DIAL] several times to select the channel group (USA and INT), if desired.
w Push [Y]/[Z] to select the desired channel to set as a tag channel.
e Push and hold [SCAN•TAG] for
1 sec. to set the displayed channel as a tag channel.
• “ ” appears.
r To cancel the tag channel setting, push and hold [SCAN•TAG] for
1 sec.
• “ ” disappears.
• Clearing all tag channels in the selected channel group
➥While pushing and holding [H/L], push [SCAN•TAG] for 3 sec. to clearing all tag channels. (until long beep changes to 2 short beeps)
■ Dualwatch/Tri- watch operation
q Push [Y]/[Z] to select the desired channel.
• While pushing and holding [H/L], push
[DIAL] several times to select the channel group (USA, INT), if desired.
w Push [DUAL] to start dualwatch or tri-watch.
• “DUAL” appears during dualwatch; “TRI” appears during tri-watch.
• Beep tone sounds when a signal is received on Channel 16.
• Tri-watch becomes dualwatch when receiving a signal on the call channel.
e To cancel dualwatch/tri-watch, push
[DIAL] again.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 37 (1,1)
■ Set mode programming
Set mode is used to change the condition of the transceiver’s functions and the microphone’s own functions:
Transceiver’s functions—
Scan mode (normal or priority), scan resume timer, dualwatch/tri-watch selection, beep tone function, internal speaker, LCD contrast, scrambler code, scrambler type and
ATIS check.
Microphone’s own functions—
Beep tone function, LCD contrast and internal speaker.
In this section, instructions are for the microphone’s own functions only. Refer to pgs. 14–16 for the setting of the other functions. (Some functions may not be selectable from the microphone.)
HM-134 REMOTE-CONTROL MICROPHONE
12
• Beep tone “BEEP”
➥Push [Y] to turn ON, [Z] to turn OFF the beep output.
Push
• LCD contrast “LCD CONTRAST”
➥Push [Y]/[Z] to adjust to a suitable LCD contrast.
• •
Push
• • q Turn power OFF.
w While pushing and holding [16•C], turn power ON.
• After beep emission, a set mode item (in the channel name indicator and condition in the channel number readout) is displayed.
e Push [16•C] to select the desired item, if necessary.
r Push [Y]/[Z] to select the desired condition of the item.
t Turn power OFF, then ON to exit set mode.
• Internal speaker “INT-SPEAKER”
➥Push [Y]/[Z] to turn the HM-134 internal-speaker ON/OFF.
Push
37
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 38 (1,1)
38
12
HM-134 REMOTE-CONTROL MICROPHONE
■ Intercom operation
q Push and hold [DUAL] for 1 sec.
to activate the intercom function.
• “IC” appears in the priority channel readout.
• The channel name disappears.
w Push [PTT] to talk.
• “ ” appears in the channel name indicator.
e Release [PTT] to listen.
Appears when the intercom function is in use.
• “ ” appears in the channel name indicator when the transceiver is in talking mode.
r Push [DUAL] to cancel the intercom function.
• Pushing [16], [SCAN•TAG] or [DIAL] is also cancels the intercom function.
For your reference:
In case the intercom mode is selected with the transceiver during microphone power OFF, the microphone power is automatically turned ON and the intercom mode is selected.
➥Push and hold [DIAL] for more than 1 sec.
• Emits intercom beep while holding.
■ Channel names
q Push [Y]/[Z] to select a channel to program.
• While pushing and holding [H/L], push [DIAL] several times to select the channel group (USA and INT), if desired.
w While pushing and holding [H/L], push [16•C].
• The 1st character of the currently programmed comment flashes.
e Push [Y]/[Z] to select a character.
r Push [SQL] to move to right; then push [Y]/[Z] to select a character.
• Push [VOL] to move to the left.
t Continue until the desired characters have been selected, then push [16•C] to return to normal operation.
• Available characters
(space) (!) (") (#) ($) (%) (&) (’) (( ) ( ))
(
✱)
(4)
(+)
(5)
(,)
(6)
(–)
(7)
(.)
(8)
(/)
(9)
(0)
(A)
(1)
(B)
(2)
(C)
(3)
(D)
(E)
(O)
(Y)
(F)
(P)
(Z)
(G) (H)
(Q)
(a)
(R)
(b)
(I)
(S)
(c)
(J) (K) (L)
(T)
(d)
(U)
(e)
(V)
(f)
(M)
(W)
(g)
(N)
(X)
(h)
(i)
(s)
(j) (k) (l) (m) (n) (o) (p)
(t) (u) (v) (w) (x) (y) (z)
(q) (r)
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 39 (1,1)
HM-134 CONNECTIONS AND INSTALLATION
13
■ HM-134 supplied accessories
Accessories included with the HM-134: Qty.
q Connection cable (OPC-1000: 6 m; 20 ft) ...................... 1 w Mounting base ................................................................ 1 e Microphone hanger ........................................................ 1 r Screws (M3 × 16; tapping) ............................................. 5
■ Installation
The optional HM-134 can be connected to the transceiver directly, as well as via the supplied connection cable for longer distance remote operation. The connector of the connection cable can be installed into a cabinet, wall, etc., as a built-in plug.
For longer distance remote operation, the optional extension cable, OPC-999 (6 m; 20 ft/Connecting between transceiver and the connection cable.), is available, and up to 2 OPC-999 can be added.
q Insert the supplied cable into the external microphone jack and tighten the cable nut as shown below.
w e r q
39
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 40 (1,1)
13
HM-134 CONNECTIONS AND INSTALLATION w To use the supplied cable as a wall socket, see the following steps.
e Using the mounting base, carefully mark off the 2 spots where the cable and screws will be fastened.
r Drill holes at these marks.
t Install the mounting base using screws as shown below.
y The installation is completed.
Mounting base Nut
Gasket
Screw holes
(approx. 2 (d) mm; 3 ⁄
32
″)
Cap
40
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 41 (1,1)
2 mm; 3 ⁄
32
˝
HM-134 CONNECTIONS AND INSTALLATION
13
Mounting base
5 mm; 3 ⁄
16
˝ 2 mm; 3 ⁄ 32 ˝ x 3
Gasket
Nut
Cap
24 to 27 (d) mm
( 15 ⁄ 16 to 1 1 ⁄ 16 ˝)
41
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 43 (1,1)
MB-75
HM-134
24 to 27 (d) mm
( 15 ⁄ 16 to 1 1 ⁄ 16 ˝)
149 (5 7 ⁄
8
˝)
MB-75 TEMPLATE
4–R11
2 mm; 3 ⁄ 32 ˝
Unit: mm (inch)
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 45 (1,1)
INSTALLATION NOTES
■ Installation notes
The installation of this equipment should be made in such a manner as to respect the EC recommended electromagnetic field exposure limits (1999/519/EC).
The maximum RF power available from this device is 25 watts. The antenna should be installed as high as possible for maximum efficiency and that this installation height should be at least 5 meters above ground (or accessible) level. In the case where an antenna cannot be installed at a reasonable height, then the transmitter should neither be continuously operated for long periods if any person is within 5 meters of the antenna, nor operated at all if any person is touching the antenna.
In all cases any possible risk depends on the transmitter being activated for long periods. (actual recommendation limits are specified as an average of 6 minutes) Normally the transmitter is not active for long periods of time. Some radio licenses will require that a timer circuit automatically cuts the transmitter after 1–2 minutes etc.
Similarly some types of transmitter, SSB, CW, AM, etc. have a lower ‘average’ output power and the perceived risk is even lower.
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page 46 (1,1)
DECLARATION
OF CONFORMITY
We Icom Inc. Japan
1-1-32 Kamiminami, Hirano-ku,
Osaka 547-0003 Japan
Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.
Kind of equipment: VHF MARINE TRANSCEIVER
Type-designation: iC- m503
Version (where applicable):
This compliance is based on conformity with the following harmonised standards, specifications or documents: i) EN 301 025-1 ii) EN 301 025-2
V1.1.2 (2000-08)
V1.1.1 (2000-08) iii) EN 301 025-3 iv) EN 300 162-2 v) EN 300 162-3 vi) EN 60945 vii) EN 60950 viii) EN 300 698-2
V1.1.1 (2001-05)
V1.1.2 (2000-12)
V1.1.1 (2001-05)
1997
1992
V1.1.1 ( 2000-8)
Signature
0560
Düsseldorf 25th Sept. 2001
Place and date of issue
Icom (Europe) GmbH
Himmelgeister straße 100
D-40225 Düsseldorf
Authorized representative name
T. Maebayashi
General Manager
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page Z (1,1)
Count on us!
< Intended Country of Use >
GER
AUT
FRA
NED
ESP
POR
SWE
DEN
BEL
LUX
ITA
GRE
FIN
SUI
GBR
IRL
A-6097D-1EU-q
Printed in Japan
© 2001 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan
01 IC-M503-(1).qxd 01.12.17 5:00 PM Page AA (1,1)
AA
10
CHANNEL LIST
• International channels
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
01 156.050
160.650
11 156.550
156.550
21 157.050
161.650
62 156.125
160.725
72 156.625
156.625
82 157.125
161.725
02 156.100
160.700
12 156.600
156.600
22 157.100
161.700
63 156.175
160.775
73 156.675
156.675
83 157.175
161.775
03 156.150
160.750
13 156.650
156.650
23 157.150
161.750
64 156.225
160.825
74 156.725
156.725
84 157.225
161.825
04 156.200
160.800
14 156.700
156.700
24 157.200
161.800
65 156.275
160.875
75 † 156.775
156.775
85 157.275
161.875
05 156.250
160.850
15 † 156.750
156.750
25 157.250
161.850
66 156.325
160.925
76 † 156.825
156.825
86 157.325
161.925
06 156.300
156.300
16 156.800
156.800
26 157.300
161.900
67 156.375
156.375
77 156.875
156.875
87 157.375
157.375
07 156.350
160.950
17 † 156.850
156.850
27 157.350
161.950
68 156.425
156.425
78 156.925
161.525
88 157.425
157.425
08 156.400
156.400
18 156.900
161.500
28 157.400
162.000
69 156.475
156.475
79 156.975
161.575
09 156.450
156.450
19 156.950
161.550
60 156.025
160.625
70 ‡ 156.525
156.525
80 157.025
161.625
10 156.500
156.500
20 157.000
161.600
61 156.075
160.675
71 156.575
156.575
81 157.075
161.675
• USA channels (for U.K. version only)
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
CH
Frequency (MHz)
Transmit Receive
01A 156.050
156.050
12 156.600
156.600
22A 157.100
157.100
64A 156.225
156.225
77 156.875
156.875
86 157.325
161.925
-- - - - 13 † 156.650
156.650
23A 157.150
157.150
65A 156.275
156.275
78A 156.925
156.925
86A 157.325
157.325
03A 156.150
156.150
14 156.700
156.700
24 157.200
161.800
66A 156.325
156.325
79A 156.975
156.975
87 157.375
161.975
-- - - - 15 † 156.750
156.750
25 157.250
161.850
67 † 156.375
156.375
80A 157.025
157.025
87A 157.375
157.375
05A 156.250
156.250
16 156.800
156.800
26 157.300
161.900
68 156.425
156.425
81A 157.075
157.075
88 157.425
162.025
06 156.300
156.300
17 † 156.850
156.850
27 157.350
161.950
69 156.475
156.475
82A 157.125
157.125
88A 157.425
157.425
07A 156.350
156.350
18A 156.900
156.900
28 157.400
162.000
70 ‡ 156.525
156.525
83A 157.175
157.175
08 156.400
156.400
19A 156.950
156.950
37A 157.850
157.850
71 156.575
156.575
84 157.225
161.825
09 156.450
156.450
20 157.000
161.600
61A 156.075
156.075
72 156.625
156.625
84A 157.225
157.225
10 156.500
156.500
20A 157.000
157.000
-- - - - 73 156.675
156.675
85 157.275
161.875
11 156.550
156.550
21A 157.050
157.050
63A 156.175
156.175
74 156.725
156.725
85A 157.275
157.275
† Low power only.
‡ Receive only.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project