Daewoo KOR-8A0R5S Service manual

Daewoo KOR-8A0R5S Service manual
S/M No. :
R8CBB5W001
Service Manual
Microwave Oven
Model: KOR-8CBB5W
✔ Caution
: In this Manual, some parts can be changed for improving,
their performance without notice in the parts list. So, if you
need the latest parts information, please refer to PPL(Parts
Price List) in Service Information Center (http://svc.dwe.co.kr).
Mar. 2010
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and
sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5)
Evidence of dropping or abuse.
(c) Before turning on power to the microwave oven for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation
and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the federal performance standard should be performed on each oven prior to release to the owner.
TABLE OF CONTENTS
SAFETY AND PRECAUTIONS ...........................................................................................................................................2
1. FOR SAFE OPERATION ..................................................................................................................................2
2. FOR SAFE SERVICE PROCEDURES .............................................................................................................2
SPECIFICATIONS ...............................................................................................................................................................3
EXTERNAL VIEW................................................................................................................................................................4
1. OUTER DIMENSION.........................................................................................................................................4
2. FEATURE DIAGRAM ........................................................................................................................................5
3. CONTROL PANEL ............................................................................................................................................6
INSTALLATION ...................................................................................................................................................................7
OPERATIONS AND FUNCTIONS.......................................................................................................................................8
DISASSEMBLY AND ASSEMBLY......................................................................................................................................9
INTERLOCK MECHANISM AND ADJUSTMENT.............................................................................................................16
TROUBLESHOOTING GUIDE ..........................................................................................................................................17
MEASUREMENT AND TEST ............................................................................................................................................21
1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ........................................................................21
2. MICROWAVE RADIATION TEST ...................................................................................................................22
3. COMPONENT TEST PROCEDURE ...............................................................................................................23
WIRING DIAGRAM............................................................................................................................................................24
PRINTED CIRCUIT BOARD..............................................................................................................................................25
1. CIRCUIT CHECK PROCEDURE ....................................................................................................................25
2. PCB CIRCUIT DIAGRAM................................................................................................................................28
3. P.C.B. LOCATION NO ....................................................................................................................................29
EXPLODED VIEW AND PARTS LIST...............................................................................................................................30
1. DOOR ASSEMBLY .........................................................................................................................................30
2. CONTROL PANEL ASSEMBLY......................................................................................................................30
3. TOTAL ASSEMBLY.........................................................................................................................................30
1
SAFETY AND PRECAUTIONS
1. FOR SAFE OPERATION
Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may
cause serious bodily injury to the operator.
IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
(Only a trained service personnel should make repairs.)
(1) A broken door hinge.
(2) A broken door viewing screen.
(3) A broken front panel, oven cavity.
(4) A loosened door lock.
(5) A broken door lock.
The door gasket plate and oven cavity surface should be kept clean.
No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven.
DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN.
The microwave oven has concealed switches to make sure the power is turned off when the door is opened.
Do not attempt to defeat them.
DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
2. FOR SAFE SERVICE PROCEDURES
1. If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the
oven.
2. If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the
oven.
(a) inform the manufacturer, importer or assembler,
(b) repair the unit at no cost to the owner,
(c) attempt to ascertain the cause of the excessive leakage,
(d) tell the owner of the unit not to use the unit until the oven has been brought into compliance.
3. If the oven operates with the door open, the service person should tell the user not to operate the oven and contact
the manufacturer and the dealer immediately.
IMPORTANT
The wire in this mains lead colored in accordance with the following code.
Green-and-yellow : Earth
Blue
: Neutral
Brown
: Live
As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows.
The wire which is colored green-and-yellow must be connected to the terminal in the plug which is marked with
the letter ‘E’, earth symbol or colored green-and-yellow.
The wire which is colored blue must be connected to the terminal which is marked with the letter ‘N’ or colored
black.
The wire which is colored brown must be connected to the terminal which is marked with the letter ‘L’ or
coloured red.
NOTE :
The oven is designed for counter-top use only.
2
SPECIFICATIONS
MODEL
KOR-8CBB5W
POWER SUPPLY
230V-50Hz, SINGLE PHASE WITH EARTHING
MICROWAVE
POWER CONSUMPTION
1200W
GRILL
COMBINATION
MICROWAVE ENERGY OUTPUT
800W
MICROWAVE FREQUENCY
2450MHz
OUTSIDE DIMENSIONS (W X H X D)
465 x 287 x 364 mm
CAVITY DIMENSIONS (W X H X D)
298 x 230 x 330 mm
NET WEIGHT
APPROX. 11.8 kg
TIMER
59 min. 90 sec.
function selections
MICROWAVE
POWER selections
10 LEVELS
cavity volume
23 L
* Specifications are subject to change without notice.
3
EXTERNAL VIEW
1. OUTER DIMENSION
4
2. FEATURE DIAGRAM
1 2
3
7 45
6
8
9
q
0
1 DOOR HOOK - When the door is closed, it will automatically lock shut.
If door is opened while oven is operating, magnetron tube will immediately stop operating.
2 DOOR SEAL - Door seal maintains the microwave within the oven cavity and prevents microwave leakage.
3 OVEN CAVITY
4 OVEN LAMP - Automatically turns on during oven operating.
5 SAFETY INTERLOCK SYSTEM
6 CONTROL PANEL
7 SPATTER SHIELD - Protects the microwave outlet from splashes of cooking foods.
8 COUPLER - This fits over the shaft in the center of the oven cavity floor.
This is to remain in the oven for all cooking.
9 GLASS COOKING TRAY - Made of special heat resistant glass. The tray must always be in proper position before operating. Do not cook food directly on the tray.
0 ROLLER GUIDE - Supports the glass cooling tray.
q DOOR SCREEN - Allows viewing of food. Microwave cannot pass through perforations in screen.
5
3. CONTROL PANEL
1
2
3
6
8
7
5
4
9
0
q
1 DISPLAY-Cooking time, power level, indicators and the current time are displayed.
2 AUTO COOK-Used to cook or reheat many of favorite food.
3 ONE TOUCH COOK-Used to cook or reheat specific quantities of food.
4 UP-Used to add time to cooking.
5 DOWN-Used to decrease time to cooking.
6 CLOCK-Used to set clock.
7 DEFROST-Used to defrost foods for time.
8 POWER-Used to set power level.
9 TIME SET PAD-Used to set the cooking time and the current time.
0 STOP/CLEAR-Used to stop the oven operation or to delete the cooking data.
q START/SPEEDY COOK-Used to start the oven
and also used to set a reheat time.
6
INSTALLATION
1. Steady, flat location
This microwave oven should be set on a steady, flat surface.
This microwave oven is designed for counter top use only.
2. Leave space behind and side
All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually,
cause failure.
3. Away from radio, and TV sets
Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or feeder
and so on. Position the oven as far from them as possible.
4. Away from heating appliances and water taps
Keep the oven away from hot air, steam and splash when choosing a place to position it, or the insulation might be
adversely affected and breakdowns occur.
5. Power supply
• Check your local power source.
This microwave oven requires a current of approximately 12 amperes, 230 Volts, 50 Hz.
• Power supply cord is about 0.8 meters long.
• Used the voltage must be the same as specified on this oven. Using a higher voltage may result in a fire or other
accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage
resulting from use of this oven with a voltage of ampere fuse other than those specified.
• This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same type.
Such a cable can be purchased from DAEWOO and must be installed by a qualified person.
6. Examine the oven after unpacking for any damage such as:
A misaligned door, broken door or a dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
7. Do not operate the oven if it is colder than room temperature
(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric shock
by providing an escape wire for the electric current. This appliance is equipped with a cord having a earthing plug. The
plug must be plugged into an outlet that is properly installed and earthed.
WARNING
Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified electrician or service-man if
the earthing instructions are not completely understood, or if doubt exists as to whether the appliance is properly
earthed, and either : If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade
earthing plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension
cord should be equal to or greater than the electrical rating of the appliance, or DO NOT USE an extension cord.
7
OPERATIONS AND FUNCTIONS
1. Connect the mains lead to an electrical outlet.
2. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always
be in place during cooking.
3. Close the door securely.
4. When the oven door is opened, the light turns off.
5. The oven door can be opened at any time during operation by pushing the door release button on the control panel.
The oven will automatically shut off. To restart the oven, close the door and then touch the START pad.
6. Each time a pad is touched. a BEEP will sound to acknowledge the touch.
7. The oven automatically cook on full power unless set to a lower power level.
8. The display will show : 0 when the oven is plugged in.
9. Time clock returns to the present time when the cooking time ends.
10. When the STOP/CLEAR pad is touched during the oven operation, the oven stops cooking and all information retained.
To erase all information (except the present time), touch the STOP/CLEAR pad once more. If the oven door is opened
during the oven operation, all information is retained.
11. If the START pad is touched and the oven does not operate, check the area between the door and door is closed
securely. The oven will not start cooking under the door is completely closed or the program has been reset.
Make sure the oven is properly installed and plugged into the electrical.
Wattage output chart
The power level is set by touching the POWER pad. The chart shows the display, the power level and the percentage
of power.
Touch POWER Pad
Power Level(Display)
Approximate Percentage of Power
Once
P-HI
100%
Twice
P-90
90%
3 times
P-80
80%
4 times
P-70
70%
5 times
P-60
60%
6 times
P-50
50%
7 times
P-40
40%
8 times
P-30
30%
9 times
P-20
20%
10 times
P-10
10%
11 times
P-00
00%
8
DISASSEMBLY AND ASSEMBLY
Cautions to be observed when troubleshooting.
Unlike many other appliances, the microwave oven is high-voltage, high-current equipment.
It is completely safe during normal operation.
However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit.
You are asked to observe the following precautions carefully.
1. Always remove the power plug from the outlet before servicing.
2. Use an insulated screwdriver and ware rubber gloves when servicing the high voltage side.
3. Discharge the high voltage capacitor before touching any oven components or wiring.
(1) Check the grounding.
Do not operate on a two-wire extension cord.
The microwave oven is designed to be used while earthed.
It is imperative, therefore, to make sure it is earthed
properly before beginning repair work.
(2) Warning about the electric charge in the high voltage capacitor.
For about 30 seconds after the operation stopped and electric
charge remains in the high voltage capacitor.
When replacing or checking parts, short between oven chassis and
the negative high terminal of the high voltage capacitor by using a
properly insulated screwdriver to discharge.
4. When the 10A fuse is blown out due to the operation of the monitor
switch; replace primary interlock switch, secondary interlock switch and
interlock monitor switch.
5. After repair or replacement of parts, make sure that the screws are
properly tightened, and all electrical connections are tightened.
6. Do not operate without cabinet.
SHORT
CAUTION : Service personnel should remove their watches whenever working close to or replacing the magnetron.
WARNING : When servicing the appliance, need a care of touching or replacing high potential parts because of
electrical shock or exposing microwave. These parts are as follows - HV Transformer, Magnetron,
HV Capacitor, HV Diode, HV fuse.
9
1. To remove cabinet
1) Remove three screws on cabinet back.
2) Pull the cabinet backward.
2. To remove door assembly
1) Remove two screws which secure the stopper hinge
top.
2) Remove the door assembly from top plate of cavity.
3) Reverse the above for reassembly.
NOTE : After replacing the door assembly, perform a check of correct alignment with the hinge and cavity front plate.
10
3. To remove door parts.
DOOR ASSEMBLY : 3511730310
REF NO.
PART CODE
A01
3512209070
A02
PART NAME
DESCRIPTION
Q’TY
FRAME DOOR
HIPS SG-970 HG-1760H
1
3517007300
BARRIER-SCREEN*0
PET T0.125
1
A03
3515204100
STOPPER HINGE *T AS
KOR-63150S
1
A04
3511719500
DOOR PAINTING AS
KOR-6C0B5S
1
A05
3517002800
BARRIER-SCREEN *I
POLYESTER T0.1
1
A06
3512300210
GASKET DOOR
PP
1
A07
3513100750
HOOK
POM
1
A08
3515102000
SPRING HOOK
PW1
1
(1) Remove the gasket door from door painting as.
(2) Remove the door frame from door painting as.
(3) Remove the stopper hinge top from door painting as.
(4) Remove the spring and the hook.
(5) Remove the barrier screen outer from door frame.
(6) Reverse the above steps for reassembly.
11
REMARK
4. Method to reduce the gap between the door seal and the oven front surface.
(1) To reduce gap located on part ‘A’
Loosen two screws on stopper hinge top, and then
push the door to contact the door seal to oven front
surface.
Tighten two screws.
(2) To reduce gap located on part ‘B’
Loosen two screws on stopper hinge under, and then
push the door to contact the door seal to oven front
surface.
Tighten two screws.
NOTE : A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm2.
12
5. To remove control panel parts.
C/PANEL ASSEMBLY : PKCPSWF620
REF NO.
PART CODE
PART NAME
DESCRIPTION
Q’TY
B01
3518571630
SWITCH MEMBRANE
KOR-6QBB5S
1
B02
3516733830
CONTROL PANEL
HIPS SG-970 HG-1760H
1
B03
PKMPMSBA60
PCB AS
6N(800W,W,10,59)
1
B04
7122401211
SCREW TAPPING
T2S TRS 4X12 MFZN
4
REMARK
(1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel assembly.
(2) Remove four screws which secure the PCB assembly to control panel.
(3) Disconnect membrane tail from the connector of the PCB assembly.
(4) Detach membrane from the control panel.
(5) Reverse the above steps for reassembly.
13
6. To remove high voltage capacitor.
1) Remove a screw which secure the grounding ring
terminal of the H.V. diode and the capacitor holder.
2) Remove the H.V. diode from the capacitor holder.
3) Reverse the above steps for reassembly.
◆ High voltage circuit wiring
7. To remove magnetron.
1) Remove a screw which secure the magnetron.
2) Remove the magnetron.
3) Reverse the above steps for reassembly.
NOTE : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall
not exceed 4mW/cm2 for a fully assembled oven with door normally closed.
Magnetron antenna
Metallic
gasket
plate
Cooling fin
Filament
terminal
<MAGNETRON>
14
8. To remove wind guide assembly.
1) Remove a screw for earthing.
2) Remove the noise filter from the wind guide.
3) Remove a screw which secure the wind guide assembly.
4) Draw forward the wind guide assembly.
5) Pull the fan from the motor shaft.
6) Remove two screws which secure the motor shaded pole.
7) Remove the motor shaded pole.
8) Reverse the above steps for reassembly.
9. To remove H.V.transformer.
1) Remove four screws holding the H.V.transformer.
2) Remove the H.V.transformer.
3) Reverse the above steps for reassembly.
15
INTERLOCK MECHANISM AND ADJUSTMENT
The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when
the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
(1) Primary interlock switch
When the door is closed, the hook locks the oven door. If the door is not closed properly, the oven will not operate.
When the door is closed, the hook pushes the button of the microswitch. Then the button of the primary interlock switch
bring it under NO condition.
(2) Secondary interlock switch and interlock monitor switch
When the door is closed, the hook pushes the lock lever downward. The lock lever presses the button of the interlock
monitor switch to bring it under NO condition and presses the button of the secondary interlock switch to bring it under
NO condition.
ADJUSTMENT :
Interlock monitor switch
When the door is closed, the interlock monitor switch should be changed (NO condition) before other switches are closed.
When the door is opened, the interlock monitor switch should be changed (NC condition) after other switches are opened.
(3) Adjustment steps
a) Loosen the mounting screw.
b) Adjust interlock switch assembly position.
c) Make sure that lock lever moves smoothly after adjustment is completed.
d) Tighten completely a mounting screw.
NOTE :
Microwave emission test should be performed after adjusting interlock mechanism. If the microwave emission exceed
4mW/cm2, readjust interlock mechanism.
16
TROUBLESHOOTING GUIDE
Following the procedure below to check if the oven is defective or not.
1. Check grounding before trouble checking.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor.
4. When checking the continuity of the switches, fuse or high voltage transformer, disconnect one lead wire from these parts
and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter.
NOTE : When electric parts are checked, be sure the power cord is not inserted the wall outlet.
Check wire harness, wiring and connected of the terminals and power cord before check the parts listed
below.
(TROUBLE 1) Oven does not operate at all ; any inputs can not be accepted.
CONDITION
CHECK
RESULT
Check continuity of interlock
monitor switch with door closed
Continuity
Fuse blows.
CAUSE
Malfunction of
interlock monitor switch
REMEDY
Replace
No Continuity
Check continuity of both primary
and secondary interlock switch
with door colosed
Check continuity of primary
inter-lock switch contact with
door partially open until interlock mon-itor switch contact
close (COM ↔ NC)
Check continuity of primary
winding of low voltage transformer
No Continuity
Malfunction of
interlock switch
Replace
Continuity
Continuity
Shorted contacts of primary
interlock switch.
Replace
No Continuity
0Ω or infinite
Approx.
310~420
(normal)
Fuse again
blows
Disconnect high voltage fuse
and operate the unit
17
Defective low
voltage transformer
Defective low
voltage trans-former
Replace
Replace
CONDITION
Outlet has
proper voltage Fuse
does not
blow.
CHECK
RESULT
CAUSE
REMEDY
No
Continuity
Defective magnetron
Replace
Check continuity of magnetron
Check continuity of
noise filter board
No
Continuity
Defective magnetron
Replace
Check continuity of
power supply cord
No
Continuity
Open power supply cord
Replace
Normal
Defective touch
control circuit
Replace
NOTE
All these switches must be replaced at the same time, please refer to “Interlock Mechanism And Adjustment”.
(TROUBLE 2) Display shows all figures selected, but oven does not start cooking, even though desired program and
time are set and START button is tapped.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
Turn table
motor and
oven lamp
do not turn
on
Check continuity of primary interlock switch
No
Continuity
Malfunction of primary interlock
switch
Adjust or
replace
Check continuity of secondary
interlock switch
No
Continuity
Check D.C. voltage being supplied to RELAY (RY2) coil
0V
Defective touch
control circuit
Approx.
15 VDC
Faulty contacts of
RELAY (RY2) or
open relay coil
18
Malfunction of secondary interlock
switch
Adjust or
replace
Replace
Replace
(TROUBLE 3)
No microwave oscillation even though fan motor rotates.
CONDITION
CHECK
No
microwave
oscillation
Check continuity of high
voltage fuse
RESULT
CAUSE
REMEDY
Continuity
Replace high voltage fuse
Check continuity of high
voltage capacitor terminals
with wires removed
Continuity
Defective high
voltage transformer
Replace
Check continuity of high voltage
rectifier in forward and backward
direction with DC megger
Continuity in
backward
direction
Defective high
voltage rectifier
Replace
Connect megger leads to magnetron terminal and magnetron
body
Continuity
Defective magnetron
Replace
Check resistance of primary and
secondary coil of high voltage
transformer
0 Ω or ∞
Defective high
voltage transformer
Replace
No
Continuity
Defective magnetron
Replace
No
Continuity
Defective high
voltage transformer
Replace
Check continuity of magnetron
with wires removed
Check continuity of filament terminal of high voltage transformer
0V
Defective touch
control circuit
Check D.C. voltage being supplied to RELAY (RY1) coil
Approx
15 VDC
19
Faulty
contacts or
RELAY (RY1)
or open relay coil
Replace
Replace
(TROUBLE 4) The following visual conditions indicate a probable defective touch control circuit
1. Incomplete segments,
1) Segments missing.
2) Partical segments missing.
3) Digit flickering other than normal display slight flickering.
4) " :0" does not display when power is on.
2. A distinct change in the display are not on when they numbers is the
display.
3. One or more digits in the display are not on when they should be.
4. Display indicates a number different from one touched.
5. Specific numbers (for example 2 or 3) will not display when the panel is touched.
6. Display does not count down or up with time cooking or clock operation.
7. Oven is programmable and cooks normally but no display shows.
8. Display obviously jumps in time while counting down.
9. Display counts down noticeably too fast while cooking.
10. Display does not show the time of day when the STOP/CLEAR button is pushed. (in case of setting the present time)
11. Oven lamp and turntable motor do not stop although cooking is finished. Check if the RELAY 2 contacts close.
If they close, replace P.C.B assembly.
CONDITION
CHECK
Display does
not show
programming
at all, even if
keyboard is
touched.
Check each pad for
continuity of the membrane
keyboard for the following keyboard check procedure
RESULT
CAUSE
REMEDY
Normal
Malfunction
of the control circuit board
Replace the
control circuit
board
Abnormal
Malfunction
of the membrane
keyboard
Replace the
membrane
keyboard
NOTE
Before following the particular steps listed above in the troubleshooting guide for the failure of membrane keyboard, please check for the continuity of each wire-harness between the membrane keyboard and P.C.B.
assembly.
20
MEASUREMENT AND TEST
1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT
Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water
exposed to the microwave as directed below.
PROCEDURE
1. Microwave power output measurement is made with the microwave oven
supplied at rated voltage and operated at its maximum microwave power
setting with a load of 1000±5cc of potable water.
2. The water is contained in a cylindrical borosilicate glass vessel having a
maximum material thickness of 3 mm and an outside diameter of approximately 190 mm.
3. The oven and the empty vessel are at ambient temperature prior to the
start of the test.
The initial temperature of the water is 10±2˚C (50±3.6˚F)
It is measured immediately before the water is added to the vessel.
After addition of the water to the vessel, the load is immediately placed on
the center of the shelf, which is in the lowest normal position.
4. Microwave power is switched on.
5. Heating time should be exactly A seconds. (Refer to table as following)
Heating time is measured while the microwave generator is operating at full power.
The filament heat-up time for magnetron is not included.
6. The initial and final temperature of water is selected so that the maximum difference between the ambient and final
water temperature is 5K.
7. The microwave power output P in watts is calculated from the following formula :
P=4187 X ▲T/t
• ▲T is difference between initial and ending temperature.
• t is the heating time.
The power measured should be B (Refer to SPECIFICATIONS)W±10.0%.
CAUTION :
1. Water load should be measured exactly to 1 liter.
2. Input power voltage should be exactly specified voltage(Refer to SPECIFICATIONS).
3. Ambient temperature should be 20±2˚C(68±3.6˚F)
Heating time for power output:
A(second)
70
64
60
56
52
49
47
44
42
40
38
B(W)
600
650
700
750
800
850
900
950
1000
1050
1100
21
2. MICROWAVE RADIATION TEST
CAUTION :
1. Make sure to check the microwave leakage before and after repair of adjustment.
2. Always start measuring of an unknown field to assure safety for operating personnel from microwave energy.
3. Do not place your hands into any suspected microwave radiation field unless the safe density level is known.
4. Care should be taken not to place the eyes in direct line with the source of microwave energy.
5. Slowly approach the unit under test until the radiometer reads an appreciable microwave leakage from the unit
under the test.
PROCEDURES
1. Prepare Microwave Energy Survey Meter, 600cc glass
beaker, and glass thermometer 100˚C(212˚F).
2. Pour 275cc±15cc of tap water initially at 20±5˚C(68±9˚F) in
the 600cc glass beaker with an inside diameter of approx.
95mm(3.5in.).
3. Place it at the center of the tray and set it in a cavity.
4. Close the door and operate the oven.
5. Measure the leakage by using Microwave Energy Survey
Meter with dual ranges, set to 2450MHz.
1) Measured radiation leakage must not exceed the value
prescribed below. Leakage for a fully assembled oven with
door normally closed must be less than 4mW/cm2.
2) When measuring the leakage, always use the 5cm(2in.)
space cone with probe. Hold the probe perpendicular to
the cabinet and door. Place the space cone of the probe
on the door, cabinet, door seem, door viewing screen, the
exhaust air vents and the suction air vents.
3) Measuring should be in a counter-clockwise direction at a
rate of 1 in./sec. If the leakage of the cabinet door is
unknown, move the probe more slowly.
4) When measuring near a corner of the door, keep the probe
perpendicular to the areas making sure the probe end at
the base of the cone does not get closer than 2 in. from
any metal. If it does not, erroneous reading may result.
22
3. COMPONENT TEST PROCEDURE
• High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle.
• It is neither necessary nor advisable to attempt measurement of the high voltage.
• Before touching any oven components or wiring, always unplug the oven from its power source and discharge the
capacitor.
1. High voltage transformer
(1) Remove connections from the transformer terminals and check continuity.
(2) Normal readings should be as follows:
Secondary winding ...................Approx. 140Ω±10%
Filament winding....................................Approx. 0Ω
Primary winding .....................................Approx. 2Ω
2. High voltage capacitor
(1) Check continuity of capacitor with meter on the highest OHM scale.
(2) A normal capacitor will show continuity for a short time, and then indicate 10MΩ once the capacitor is charged.
(3) A shorted capacitor will show continuous continuity.
(4) An open capacitor will show constant 10MΩ.
(5) Resistance between each terminal and chassis should be infinite.
3. High voltage diode
(1) Isolate the diode from the circuit by disconnecting the leads.
(2) With the ohmmeter set on the highest resistance scale measure the resistance across the diode terminals.
Reverse the meter leads and again observe the resistance reading.
Meter with 6V, 9V or higher voltage batteries should be used to check the front-back resistance of the diode, otherwise an infinite resistance may be read in both directions.
A normal diode’s resistance will be infinite in one direction and several hundred KΩ in the other direction.
4. Magnetron
For complete magnetron diagnosis, refer to “Measurement of the Microwave Power Output”.
Continuity checks can only indicate and open filament or a shorted magnetron.
To diagnose for an open filament or a shorted magnetron.
(1) Isolate magnetron from the circuit by disconnecting the leads.
(2) A continuity check across magnetron filament terminals should indicate 0.1Ω or less.
(3) A continuity check between each filament terminal and magnetron case should read open.
5. Fuse
If the fuse in the primary and monitor switch circuit is blown when the door is opened, check the primary and monitor
switch before replacing the blown fuse.
In case the fuse is blown by an improper switch operation, replace the defective switch and fuse at the same time.
Replace just the fuse if the switches operate normally.
23
WIRING DIAGRAM
24
PRINTED CIRCUIT BOARD
1. CIRCUIT CHECK PROCEDURE
1. Low Voltage Transformer check
The low voltage transformer is located on the P.C.B.
Measuring condition: input voltage : 230V/Frequency : 50Hz
Terminal Voltage
5-6-7
LOAD
AC 12.6 V
NO LOAD
AC 14.7 V
NOTE :
1. Refer to Circuit Diagram (point 4).
2. Secondary side voltage of the low voltage transformer changes in proportion to fluctuation of power source voltage.
3. The allowable tolerance of the secondary voltage is within 5% of nominal voltage.
2. Voltage check
Key check point
NO
CHECK POINT
1
IC 1 PIN 5
2
IC 1 PIN 8
REMARK
5 VDC
T:20ms(50Hz)
3
IC 1 PIN 35 OR PIN 36
T:250ns(4MHz)
Check method
NO
MEASURE POINT
1
MP1
2
MP2
WAVE FORM
REMEDY
REMARK
DC 5V 0.25V
Replace VL1, EC1
NO LOAD
DC 12V 2.0V
Replace EC2, D11, D13, D14
NO LOAD
NOTE :
Each measure point must be measured with GND point.
25
MP1
MP2
GND
Measure Point
26
3. When there is no microwave oscillation
1) When touching START pad, oven lamp does not turn on.
Fan motor does not rotate, but cook indicator in display comes on.
B
A
RY2
42
D10
(TRAY
LAMP)
Q10
RY2
- Check method
POINT
A
B
RELAY 2 ON
5VDC
GND
RELAY 2 OFF
GND
12VDC
STATE
2) When touching START pad, oven lamp turns on.
Fan motor and turntable rotate and cook indicator in display comes on.
B
A
RY1
41
D8
(M/W)
Q9
RY1
- Check method
POINT
A
B
RELAY 1 ON
5VDC
GND
RELAY 1 OFF
GND
12VDC
STATE
4. When the door is opened during operation, the count down timer does not stop.
A
B
R1
CN1
1
2
27
R10
C1
R9
D.O.M SW
+5V
-Check method
POINT
A
B
1) DOOR OPEN
OPEN
5VDC
2) DOOR CLOSED
CLOSE
GND
STATE
CHECK NO
1
C2
METHOD
REMEDY
Check the stage (ON, OFF) of the door open monitor switch by
resistance measurement.
5. When the digital clock does not operate properly.
Refer to Circuit Diagram.
POINT
WAVE FORM
IC 1 PIN 8
T:20ms(50Hz)
* If clock does not keep exact time, you must check resistor R20 and zener diode ZD2.
27
Replace door open monitor
switch.
2. PCB CIRCUIT DIAGRAM
28
3. PCB LOCATION NO.
NO
NAME
SYMBOL
SPECIFICATION
PART CODE
Q’TY
1
BUZZER
BZ1
BM-20K
3515600100
1
2
C ARRAY
CA1
7P(6) 1000PF M 50V
CN6XB-102M
1
3
CAPACITOR ELEC
EC1
50V RS 10UF
CEXE1H100A
1
4
CAPACITOR ELEC
EC2
25V RSS 1000MF
CEXF1E102V
1
5
CONNECTOR WAFER
CN1
YW396-02V
3519150520
1
6
CONNECTOR WAFER
CN2
FCZ 254-11
441M367160
1
7
CONNECTOR WAFER
CN3
YW396-05AV
3519150510
1
8
DIODE RECTIFY
D1~5, D8~D12
1N4148
DZN4148---
10
9
DIODE RECTIFY
D13,14
KN4004A
DZN4004A--
2
10
DIODE ZENER
ZD1
UZ- 3.3BSB 1/2W
DZUZ3R3BSB
1
11
DIODE ZENER
ZD2
UZ- 5.1BSB 1/2W
DZUZ5R1BSB
1
12
LED DISPLAY
DP1
ELF-496GWB
DDDG631H--
1
13
PCB MAIN
M158-1
81.5X139.9
3514315411
1
14
R ARRAY
RA2
8P(7) 1/8 100K OHM J
RA-88X104J
1
15
R ARRAY
RA1
7P(6) 1/8 100K OHM J
RA-87X104J
1
16
RESISTOR
R2~8
1/6W 330 5%
RD-AZ331J-
7
17
RESISTOR
R1,10,12,17,18,22
1/6W 1K 5%
RD-AZ102J-
6
18
RESISTOR
R9
1/6W 100K 5%
RD-AZ104J-
1
19
RESISTOR
R11
1/6W 200 5%
RD-AZ201J-
1
20
RESISTOR
R13,R19,R20
1/6W 10K 5%
RD-AZ103J-
3
21
RESISTOR
R14
1/6W 1M 5%
RD-AZ105J-
1
22
RESISTOR
R21
1/4W 51 5%
RD-4Z510J-
1
23
RESONATOR CERA
CR1
CRT 4.00MS
5P4R00MTS-
1
24
IC REGULATOR
VL1
MC7805C
1CPMC7805C
1
25
TRANSISTOR
Q1~5
KRA106M
TZRA106M--
5
26
TRANSISTOR
Q9~11
KRC106M
TZRC106M--
3
27
TRANSISTOR
Q6
KTA-1266Y
TZTA1266Y-
1
28
CAPACITOR CERA
C5
102 50V Z AXIAL
CCZB1H102K
1
29
CAPACITOR CERA
C1~4,C6~7
104 50V Z AXIAL
CCZF1H104Z
6
30
TRANS POWER
LVT1
DMR-631FS EU
5EPK035303
1
31
WIRE COPPER
J1~J10,J13,J14
1/0.52 TIN COATING
85801052GY
12
32
WIRE COPPER
J11,J12
1/0.52 TIN COATING
85801053GY
2
33
SW RELAY
RY2
CS11-12SH 1C 1P
5SC0101128
1
34
IC MICOM
IC1
HMS81C1708B-HN017-1
150S63MB00
1
35
WIRE COPPER
SJ3, SJ4, SJ6
1/0.52 TIN COATING
85801052GY
1
36
SW RELAY
RY1
G5G-1A DC12V
5SC0101121
1
29
EXPLODED VIEW AND PARTS LIST
1. DOOR ASSEMBLY
Refer to Disassembly and assembly.
2. CONTROL PANEL ASSEMBLY
Refer to Disassembly and assembly.
3. TOTAL ASSEMBLY
30
✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the
parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service
Information Center (http://svc.dwe.co.kr).
NO
PART CODE
PART NAME
A00
B00
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
3511730310
PKCPSWF620
3510805300
3516109970
7112401011
7122401211
7122401211
7112401011
35113AEQ0D
7112401011
3518607600
7121402511
3963512310
3512517000
3511800300
3518003700
3516004000
7272400811
3513003200
3518302201
3518400900
3518701100
3518122310
3516003700
3510311700
7112401011
3512101900
3512102000
7272400811
3515201101
3512718720
4415A17352
4415A66910
3518571000
3513702620
3513811750
3513601600
7112401011
3966031600
3518906400
3513003410
7272400811
3511406220
3517400620
3512517300
3514700710
3517203600
DOOR AS
CONTROL-PANEL AS
CABINET AS
CAVITY AS
SCREW TAPPING
SCREW TAPPING
SCREW TAPPING
SCREW TAPPING
CORD POWER AS
SCREW TAPPING
NOISE-FILTER
SCREW TAPPING
MOTOR SHADED POLE
GUIDE WIND
FAN
MAGNETRON
SCREW TAPTITE
SPECIAL SCREW
HOLDER HV CAPACITOR
CAPACITOR HV
DIODE HV AS
FUSE HV
TRANS HV
SPECIAL SCREW
BASE
SCREW TAPPING
FOOT *B
FOOT *F
SPECIAL SCREW
STOPPER HINGE *U
HARNESS MAIN
SW MICRO
SW MICRO
SWITCH PUSH
LEVER LOCK
LOCK
LAMP
SCREW TAPPING
MOTOR SYNCRO
THERMOSTAT
HOLDER THERMOSTAT
SCREW TAPTITE
COVER WAVE GUIDE
COUPLER
GUIDE ROLLER
ROLLER
TRAY
DESCRIPTION
KOR-8CB75S
KOR-6QBB5W
KOR-61150S
KOR-8A0R5S
T1 TRS 4X10 MFZN
T2S TRS 4X12 MFZN
T2S TRS 4X12 MFZN
T1 TRS 4X10 MFZN
3X0.75 70X70 100-RTML
T1 TRS 4X10 MFZN
DWLF-M12 A
T2S PAN 4X25 MFZN
230V 50HZ MW10CA-M02
PP
PP+30%GLASS
2M218JFL 6CF
T2 BOLT FLANGE 5X12 DACRO
TT3 TRS 4X8 MFZN
SECC T0.6
2100VAC 0.98UF #187 75MM
HVR-1X-30B #187
5KV 0.55A HV-41A55-02
R1S58B(LA00)
TT3 HEX 4X8 FLG MFZN
SBHG T0.6
T1 TRS 4X10 MFZN
PP
PP
TT3 TRS 4X8 MFZN
SCP-1 T2.5
KOR-8A0R5S
VP-533A-OF SPNO #187 200G
VP-531A-OF SPNC #187 200G
MP101C
POM
CHEIL(FH-44N)
BL 240V 25W T25 C7A H187
T1 TRS 4X10 MFZN
220/240V 50/60HZ ST-16 MN73MQAD A
OFF:85 ON:75 #187 NB
PP(BK)
TT3 TRS 4X8 MFZN
PP J640A WHITE
XAREC
PP 5113MF6 A353B
TEFLON
GLASS
31
Q'TY
1
1
1
1
3
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
1
5
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
1
DAEWOO ELECTRONICS CORP.
1-2, Jeo-dong 1(il)-ga, Jung-gu, Seoul, Korea
C.P.O. BOX 8003 SEOUL, KOREA
TELEX: DWELEC K28177-8
CABLE: “DAEWOOELEC”
S/M NO. :
PRINTED DATE: Mar. 2010
ABOUT THIS MANUAL
[email protected]@incN
Է‫΂ܞ ړ‬ĸ ࣃ‫ۉ‬ʷ
V Ѩ‫ێ ݖ‬Οӂ˱ T ࠚ
ɽ
ʁ
Ũٙ‫ ݘ‬ɮ
[email protected]@[email protected]@l
[email protected]
‫܂‬
RPQPNPSNQP
ր
Q޵
R޵
‫ۑ‬
‫܄‬
S޵
T޵
U޵
‫܆‬
ࣽ
Ŕ
ÿ
‫ې‬
॥
լ
[email protected]@߭ SS
QPNPSNQPMह‫ݖ‬[email protected]ह‫˒ݖ‬[email protected][email protected][email protected][email protected][email protected][email protected]@֭Ŕ X
QPNPSNQQMS@ր‫֭@܄‬Ŕ XQ
ِ͊ߏ
vision ɽ ʁ
і О ր
telZ [email protected] WSPMSWXX
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement