NX-8E Installation Manual Rev G
NetworX Series
NX-8E Control Panel
Installation and Startup
© 2002 GE Interlogix
All rights reserved.
Printed in the United States of America.
These instructions do not purport to cover all details or variations in equipment nor to provide every
possible contingency to be met during installation, operation, and maintenance. If further information is
desired or if particular problems arise that are not covered sufficiently for the purchaser’s purpose, the
matter should be referred to GE Interlogix, Gladewater, Texas, USA.
This document contains proprietary information of GE Interlogix, USA and is furnished to its customer
solely to assist that customer in the installation, testing, operations, and/or maintenance of the
equipment described. This document shall not be reproduced in whole or in part nor shall its contents
be disclosed to any third party without the written approval of GE Interlogix.
Please refer to the current GE Interlogix product catalog for detailed warranty information.
Main
800-727-2339
Outside the US
903-845-6941
Main Fax
903-845-6811
Web: www.caddx.com
www.ge-interlogix.com
Technical Support
Tech Support Fax
Sales & Literature
NetworX is a trademark of the GE Interlogix companies.
800-727-2339
903-845-8409
800-547-2556
Table of Contents
I.
GENERAL DESCRIPTION...........................................................................................................................3
II.
ORDERING INFORMATION ........................................................................................................................3
III.
GLOSSARY..................................................................................................................................................4
IV.
PROGRAMMING THE LED KEYPADS .......................................................................................................8
V.
PROGRAMMING THE CONTROL.............................................................................................................10
ENTERING THE PROGRAM MODE .................................................................................................10
SELECTING THE MODULE TO PROGRAM.....................................................................................10
PROGRAMMING A LOCATION.........................................................................................................10
EXITING A LOCATION ......................................................................................................................10
EXITING THE PROGRAM MODE .....................................................................................................10
VI.
PROGRAMMING DATA .............................................................................................................................12
NUMERICAL DATA............................................................................................................................12
FEATURE SELECTION DATA...........................................................................................................12
VII.
LOADING FACTORY DEFAULTS .............................................................................................................12
VIII.
ENROLLING MODULES AND KEYPADS .................................................................................................12
IX.
L
X.
PROGRAMMING LOCATIONS..................................................................................................................13
QUICK START INSTALLATION .........................................................................................................12
Table X-1 COMMUNICATOR FORMAT SELECTIONS....................................................................13
REPORTING EVENTS TO PHONE NUMBER 1 ...............................................................................14
REPORTING EVENTS TO PHONE NUMBER 2 ...............................................................................15
REPORTING EVENTS TO PHONE NUMBER 3 ...............................................................................16
XI.
DEFAULT ZONE TYPES (Configurations).................................................................................................19
Table XI-1 AUXILIARY OUTPUT EVENT SELECTION.....................................................................25
XII.
PROGRAMMING WORKSHEETS .............................................................................................................45
XIII.
NX-8E WIRING DIAGRAM.........................................................................................................................66
XIV.
TERMINAL DESCRIPTIONS .....................................................................................................................67
KEYPAD MAXIMUM WIRE RUN .......................................................................................................67
XV.
APPENDIX 1 ..............................................................................................................................................69
XVI.
APPENDIX 2 ..............................................................................................................................................70
XVII.
APPENDIX 3 ..............................................................................................................................................71
XVIII.
APPENDIX 4 ..............................................................................................................................................72
XIX.
TELEPHONE COMPANY INTERFACE INFORMATION ...........................................................................73
XX.
NOTICES ...................................................................................................................................................74
XXI.
UNDERWRITERS LABORATORIES INFORMATION ...............................................................................75
XXII.
BOARD INSTALLATION ............................................................................................................................77
XXIII.
SPECIFICATIONS .....................................................................................................................................78
NX-8E CONTROL
1
SAFETY SYMBOL LEGEND
Warning
Caution
Indicates a procedure, practice, condition, or statement that, if not strictly
observed, could result in personal injury.
* This symbol indicates electrical warnings and cautions.
Indicates a procedure, practice, condition, or statement that, if not strictly
observed, could result in damage to or destruction of equipment or property.
** This symbol indicates general warnings and cautions.
Indicates an essential or important procedure, instruction, condition, or
statement.
Note
Tip
2
Indicates a user tip. Provides helpful information that is not normally defined
in regular use, but from an experienced user.
NX-8E CONTROL
I.
GENERAL DESCRIPTION
The NetworX NX-8E represents a new approach to security systems design. Drawing on our experience in the world
market as the largest exporter of USA manufactured controls, we have developed the most flexible, durable, and userfriendly control ever seen in our industry. Featuring sophisticated software, which allows up to 240 users to interface
with 192 zones, 8 partitions, and a host of integrated fire, access, verification, and input/output modules, all reported
with the most comprehensive and fast SIA and Contact ID formats. The NetworX design allows a fully loaded system
to be housed in one single metal enclosure, establishing for the first time, a logical solution and design response to
modular systems. Up to 32 modules can be added to expand the capabilities of the NX-8E. For product warranty
information, please refer to the Interlogix Product Catalog.
II.
ORDERING INFORMATION
PART #
NX-8E
NX-848E-KIT
NX-108E
NX-116E
NX-124E
NX-148E
NX-200 **
NX-216E
NX-320E
NX-408E #
NX-416E #
NX-448E #
NX-507E
NX-508E
NX-534E **
NX-540 **
NX-591E **
NX-870E
NX-1192E
NX-1208E
NX-1248E
NX-1308E
NX-1316E
NX-1324E
NX-1448E
P-0003 **
8920 **
DESCRIPTION
NX-8E Control Only
NX-8E Control, NX-148E LCD Keypad, 16.5V 40VA Transformer
8 Zone LED Keypad
16 Zone LED Keypad
24 Zone LED Keypad
Alphanumeric LCD Keypad
Zone Doubling Kit (Includes 100 3.74k and 100 6.98k resistors)
16 Zone Expander Module
Smart Power Supply and Buss Extender
8 Zone Wireless Expansion Module (UL LISTED PART #60-904)
16 Zone Wireless Expansion Module (UL LISTED PART #60-904)
48 Zone Wireless Expansion Module (UL LISTED PART #60-904)
Seven Relay Module
Eight Output Module
Two-Way Listen-In Module
"Operator" Telephone Interface Module
Cellemetry Interface
Fire Supervision Module
192 Zone LCD Keypad
8 Zone LED Keypad
48 Zone LCD Keypad
8 Zone LED Door Design Keypad
16 Zone LED Door Design Keypad
24 Zone LED Door Design Keypad
48 Zone Fixed Language Icon Keypad
RS232 Adapter Cable
4-Wire Cable (For use on AUX 1-4)
** These products have not been tested and approved by Underwriters Laboratories, Inc.
# These wireless devices are only UL listed for residential applications.
NX-8E CONTROL
3
III.
GLOSSARY
Abort - If enabled, the NX-8E will wait the programmed number of seconds in location 40 prior to sending an alarm.
During this delay time, the "Cancel" LED will flash. To abort the report, type in a code and press the [Cancel] key. The
LED will extinguish. If the report is not aborted within the allotted time, the LED will extinguish when the report is sent.
ADialer Delay@ must be enabled in the ACharacteristic Select@ of locations 110-169. (See locations 40 and 110-169,
pages 23 and 33-37)
AC Fail / Low Battery Report/Warning- The NX-8E can be programmed to report AC failure and/or Low Battery
conditions to the central station. It can also be programmed to sound the keypad immediately upon detection of the
condition. The AC failure report/warning can be delayed. (See locations 37 and 39, page 22)
AC Power / Low Battery Sounder Alert- If enabled, the NX-8E will beep the keypad sounder upon arming or
disarming if the AC power is missing or a low battery has been detected. (See location 23, page 18)
Arm / Disarm Codes - The NX-8E can have 240 four-digit codes or 160 six-digit codes to arm/disarm the control. All
codes must have the same number of digits. The factory default for User #1 is [1]-[2]-[3]-[4] when using a 4-digit code,
or [1]-[2]-[3]-[4]-[5]-[6] for a 6-digit code. This code can then be used to enter the new arm/disarm codes. (See
location 41, page 23)
Automatic Arming - If programmed, the NX-8E will Auto Arm at a specified time. At this time, the keypad will beep for
50 seconds before the panel arms. The arming process will be stopped if a code is entered on the keypad. The NX-8E
will attempt to arm after every 45 minutes of inactivity until the next “opening” time (loc. 52), or until the system is
armed. The 45-minute timer will be extended when there is activity in the building causing the "Ready" LED to turn off
and on. If closing reports are sent, the user code will be 97. (See locations 23, and 52-55, pages 18 and 26) NOTE:
For UL installations, this feature shall be disabled.
Auto Cancel / Abort - If enabled, the Cancel and/or Abort features will be automatic (pressing the [Cancel] button is
not required). The Cancel and Abort features, in locations 23 and 40 respectively, must be enabled to permit this Auto
feature to work. For proper operation of these features, ADialer Delay@ must be enabled in the ACharacteristic Select@
of locations 110-169 Zone Types. (See location 41, page 23)
Automatic Bypass / Instant Arming - When enabled, the control panel can automatically bypass interior follower
zones if an exit is not detected during the exit delay time. Entry delay zones can also be made instant.
(See location 23, segments 1 and 3, page 18)
Auto Test- This feature will cause the panel to call the central station to report a communicator test at a specified
interval. (See location 51, page 26)
Auxiliary Outputs- The NX-8E has four programmable outputs that can be used to activate relays, LED=s, etc. (See
the terminal description on page 67 and locations 45-50, pages 24-25)
Auxiliary Power Overcurrent- The NX-8E will illuminate the "Service" LED on the keypad whenever too much
current is drawn from any device powered by the system. This condition can be reported to the central station.
(See location 37, page 22)
Box Tamper- The NX-8E has an input for a normally closed tamper switch (see terminal drawing). The Box Tamper
can be programmed to report and/or sound the siren and/or the keypad. These terminals can be enabled or disabled
in programming. (See locations 37 and 39, page 22)
Built In Siren Driver - The NX-8E has a built-in 112db-siren driver. When desired, this built-in driver can be easily
converted to a 1-amp voltage output through programming. (See location 37, page 22)
Bypass Toggle- This feature will enable the end user to toggle (turn on or off) the bypass of an interior zone with the
system armed by pressing the [Bypass] key. (See location 23, page 18)
Call Back- When enabled, the control will use the call back phone number to call the download computer before
beginning a download. (See location 21, page 18)
Cancel - If enabled, the NX-8E will send a "Cancel" report if when the system is disarmed and the [Cancel] button is
pressed within 5 minutes of an alarm. Once the [Cancel] key is pressed, the "Cancel" LED will illuminate until the
central station acknowledges the "Cancel" report. ADialer Delay@ must be enabled in the ACharacteristic Select@ of
locations 110-149. (See location 23, page 18)
4
NX-8E CONTROL
Code Required Options- The NX-8E can be programmed to require a code for bypassing zones and/or initiating a
download using the [r]-[9]-[8] or [r]-[9]-[9] function. (See locations 23 and 41, pages 18 and 23)
Communication Formats- The NX-8E can report in multiple formats. It is recommended that you use Contact ID or
SIA formats if possible. If you wish to report to a pager or in a 4+2 format to a central station, you must program each
code to be reported. (See locations 56-83 and 111-169, pages 27-29 and 33-37)
Cross Zoning - This feature requires two or more trips on a zone or zones programmed as "cross zones" within a
specified time before reporting an alarm. During the time between trips, the NX-8E can be programmed to sound the
keypad and/or the siren. The NX-8E can also be programmed to report an alarm after two or more trips on the same
zone. (See locations 37, 39, 40 and 110-149, pages 22, 23, 33-37)
Dual / Split / Multiple Reports - The NX-8E can send communication reports to three different phone numbers for
dual, split or multiple reports selectable by event or partition. (See locations 4, 10, and 16, pages 14, 15, 17)
Duress Code- If a duress code is programmed the NX-8E will send a duress signal whenever the panel is armed or
disarmed with this code. If open/close reports are sent, the user code will be 254. (See location 44, page 24)
Dynamic Battery Test - The NX-8E can be programmed to perform a Dynamic Battery Test for a selected duration
the first time the panel is armed or disarmed every day, as well as by pressing [r][4] Test Function. If the panel is not
armed or disarmed during the day, it will perform the test at midnight. The NX-8E can also be programmed to perform
a missing battery test every 12 seconds. (See locations 37 and 40, pages 22 and 23)
Early to Open / Late to Close – If an opening occurs before the opening and closing times, the NX-8E will send an
“Early Open” report. If it fails to close on or before the designated closing time, the NX-8E will send a “Late to Close”
report.
End of Line Resistor Defeat – The NX-8E can be programmed to make zones 1-8 for normally closed operation only,
eliminating the need for the end of line resistors on these zones. When a zone is programmed for normally closed
operation, a short on that zone will not change the loop condition, and an open on that zone will produce a faulted
condition. This feature will be ignored by any Priority zone. (See locations 111-169, pages 33-37) NOTE: For UL
installations, all zones must be programmed as supervised.
Entry-Guard - This unique low level arming mode has been developed to reduce the most common source of false
alarms. When armed with the AInstant@ LED on, the opening of any zones designated as "Entry Guard zone" will
initiate the keypad sounder and start the entry delay before creating an alarm. All other zones will function as normal.
This arming mode will encourage system owners to use their system more frequently when the premises are
occupied. (See locations 111-169, pages 33-37) NOTE: For UL installations, this feature shall be disabled.
Exit Error - If enabled, the NX-8E will send an "Exit Error Report" if an entry/exit zone is faulted at the instant the exit
delay expires. This report will be sent along with the user number that armed the system, if the panel is not disarmed
before the entry delay expires. The alarm report will also be sent. Even if this feature is not enabled, the siren will
sound if any entry/exit zone is faulted at the instant the exit delay expires. (See location 23, page 18)
Expander Trouble- The NX-8E will report expander trouble to the central station if enabled. This condition will
illuminate the "Service" LED on the keypad even if not reported. NOTE: The keypads are considered expanders. The
number of the expansion devices reported can be found on page 53. (See location 37, page 22)
Fail to Communicate- The NX-8E will illuminate the "Service" LED if a report fails to reach the central station. If
enabled, when the next report is successfully communicated, a Fail to Communicate code will be reported. (See
location 37, page 22)
Fire Alarm Verification - When enabled, the NX-8E will verify a Fire alarm by requiring more than one trip on a
smoke detector within a specified time before creating an alarm. (See location 40, page 23) This feature is not
approved for residential use in California.
Force Arming - When enabled, the NX-8E can be Force Armed with zones violated. Under this condition, if a force
armable zone is not secure, the "Ready" LED will flash. At the end of the exit delay, these zones will become
bypassed. If these zones become secured any time during the arming cycle, they will be unbypassed and active in the
system. If "Bypass Report" is enabled, the force arming zones can be programmed to report bypass when they are
Force Armed (default), or to not report bypass even if "Bypass Report" is enabled. (See locations 37, and 111-169,
pages 22 & 33-37) NOTE: For UL installations, this feature shall be disabled.
Ground Fault- If the NX-870 is used, a fault of the earth ground can be reported to the central station. If it is not
reported, this condition will illuminate the "Service" LED on the keypad. (See location 37, page 18)
NX-8E CONTROL
5
Group Bypass - A designated group of zones can be programmed to bypass by pressing [Bypass]- [0]-[Bypass][Bypass] prior to arming. (See locations 111-169, pages 33-37) NOTE: For UL installations, this feature shall be
disabled.
Immediate Restore By Zone- The NX-8E can be programmed to send alarm and restore reports as soon as they
occur, or wait until the siren time has expired. (See location 37, page 22)
Internal Event Log - Up to 512 events can be stored in memory along with the date and time of the event. These
events can later be viewed through downloading. All reportable events report to the log.
Keypad Activated Panics- The NX-8E has three keypad activated panics that will send reports to the central station:
Auxiliary 1 (Fire), Auxiliary 2 (Medical), and Keypad Panic. Auxiliary 1 will activate the steady (Fire) siren, Auxiliary 2
will sound the keypad, and the Keypad Panic can be programmed to be silent or audible (sound siren). (See location
23, page 18)
Keypad Sounder Control- The NX-8E can be programmed to sound the keypad sounder for certain events. (See
location 39, page 23)
Keypad Tamper- If enabled, the NX-8E will disable the keypad for 60 seconds and communicate a tamper signal to
the central station if 30 keypresses are entered without producing a valid code. (See location 23, page 18)
Keyswitch Arm/Disarm - Any zone on the NX-8E can be programmed as a keyswitch zone. If this is done, a
momentary short on this zone will arm/disarm the control. If opening/closing reports are sent, the user code will be 99.
(See "Default Zone Types", page 19)
LED Extinguish- This feature will extinguish all LEDs on the keypad, except the "Power" LED, after 60 seconds
without a keypress. Pressing any numeric key will illuminate all LED=s. (See location 23, page 18)
Local Programming Lockout- This feature will disable programming of all locations or specified locations from the
keypad. (See location 21, page 18)
Log Full Report- A report can be sent to the central station when the event log is full. (See location 37, page 21)
Lost Clock Service Light- The NX-8E can be programmed to illuminate the "Service" LED when the internal clock
has an invalid time due to power loss. (See location 37, page 22)
Manual Test- The NX-8E can be programmed to perform a bell and/or communicator test when [r]-[4]-[4] is entered
while the system is in the disarmed state. (See location 37, page 22)
Night Mode – (Applies to NX1208E / NX1248E keypads) In this mode, the control panel will bypass all zones that
have the Entry Guard feature enabled. (See location 23, page 18)
On Board Zone Disable- The eight zones on the NX-8E panel can be disabled in order to have a completely wireless
alarm system. (See location 37, page 22)
Partitions - The NX-8E can be partitioned into a maximum of eight separate systems with distinct reporting codes,
user codes, and operating features for each system. (See locations 26 - 36, pages 20-22)
Program Code - The factory default for the "Go To Program" code is [9]-[7]-[1]-[3] when using a 4-digit code or, if the
6-digit option is used, the default is [9]-[7]-[1]-[3]-[0]-[0]. The program code can also be used as an Arm/Disarm code.
If used as an Arm/Disarm code, and open/close reports are sent, the user code will be 255. (See location 43, pg 24)
Quick Arm Feature - The NX-8E has a one-button "Quick Arm" feature which can be used to arm the system by
pressing the [Exit] key or the [Stay] key on the keypad. If closing reports are sent, the user code will be 98. (See
location 23, page 18)
Recent Closing - If enabled, the NX-8E will send a "Recent Closing Report" to the central station if an alarm occurs
within 5 minutes after the panel is armed. The user number that armed the system will also be sent. (See location
23, page 18)
Re-exit - The NX-8E has the ability to restart the exit delay for a quick exit without disarming the system by pressing
the [Exit] key while the system is armed. (See location 23, page 18)
Shutdown- This mode will cause the keypads to turn off all LED=s, except the "Power" LED, and not accept
keypresses. (See location 21, page 18)
6
NX-8E CONTROL
Siren Blast For Arming- The NX-8E can be programmed to give a one-second siren blast when the panel is armed,
at the end of the exit delay, or when the central station receiver acknowledges the closing report. It can also give one
blast for remote (keyswitch) arming and two blasts for remote disarming. (See location 37, page 22)
Siren Supervision - The NX-8E has a ASiren Supervision@ circuit that will constantly monitor the siren on the NX-8E
and can be programmed to report if the wires are cut. (See location 37, page 22)
Silent Exit Option - The exit delay can be silenced by pressing [r]-[Exit] before arming the control panel or when
using the re-exit feature. The exit delay can also be silenced permanently in all partitions. (See location 37, page
22)
Start/End Programming and End Downloading- A report can be sent when local programming is started and
ended. A report can also be sent when a download session ends. (See location 37, page 22)
Swinger Shutdown - This feature allows a zone or zones to be automatically bypassed after a specified number of
alarms. When a zone is tripped, the alarm ‘counter’ reflects “1” in memory. If a new (first) alarm is detected in a
different zone, the counter remains at “1”. If an alarm is detected on a previously tripped zone, the count increments to
“2”. The ‘counter’ will increment each time an alarm is detected on a zone with multiple trips. Bypassing will occur on
the zone that causes the count to equal the number programmed in location 38; the ‘counter’ will reset to zero (0); and
begin a new trip count where the next alarm will set the ‘counter’ to 1. If immediate restore is enabled in location 37,
the alarms (and restores, if enabled) will be sent as they occur. If immediate restore is not enabled, a second or
subsequent alarm will not be sent until the siren times out. (See location 37 and 38, page 21) NOTE: For UL
installations, this feature shall be disabled.
Telephone Line Monitor - The NX-8E has a Telephone Line Monitor that monitors the voltage and current of the
telephone line for a detection of a faulted phone line. This condition can also be reported to the central station. If the
report is enabled, only the Telephone Line Restore will be reported unless the NX-870 is being used. (See locations
37, 39, and 40, pages 22-23)
Temporal Siren Disable - If disabled, the Fire Siren will be steady and Fire Voltage Out will be the same as Burglary
(continuous). Otherwise, the Fire Siren will be temporal. (See location 37, page 22) NOTE: For UL installations,
do NOT disable.
Tone Sniff Answering Machine Defeat- If enabled, only one call is required to defeat the answering machine. To use
this feature you must have a Hayes 1200 Smart Modem or a CADDX 1200 module. From the computer, call the panel
as normal. When the answering machine answers, the panel will hear the tones from the modem and seize the phone
line for a download. (See location 21, page 18)
Two Call Answering Machine Defeat - If enabled, to defeat an answering machine, two telephone calls must be
made to the premises. On the first call, let the phone ring one or two times. The control panel will detect these rings
and start a 45-second timer, during which, the control panel will answer the next call on the first ring. This is not
recommended for commercial applications. (See location 21, page 16)
Walk-Test Mode - If enabled, entering [r] [Chime] followed by a user code will allow a walk-through zone test where
all zones become silent and local (non-reporting). During this test the chime light will flash on the LED keypad. Each
time a zone is faulted, the zone light on the LED keypad will illuminate and the chime will sound. The number of the
faulted zone(s) will be displayed on the LCD keypad. It will also be entered into alarm memory and the internal log.
To exit at any time during this mode, enter a user code. Otherwise the AWalk-Test Mode@ will automatically exit after
15 minutes. (See location 41, page 22)
Wireless Sensor Missing/Low Battery - The NX-8E will send a report to the central station when a wireless sensor
has detected a low battery or has not reported to the receiver. The "Service" LED will illuminate when either condition
exists. (See location 37, page 21)
Zone Activity Monitor – This feature will send a report to the central station when a particular zone does not change
conditions within the specified number of days programmed. (See location 40, page 23 and locations 110-169,
page 33-37).
Zone Bypassed Sounder Alert- If this feature is enabled, the NX-8E will beep the keypad sounder upon arming if a
zone is bypassed. (See location 23, page 18)
Zone Doubling - This feature allows you to use the eight zones on the panel as sixteen normally closed zones. When
this feature is used, European double E.O.L. configuration cannot be used on the first sixteen zones. THIS FEATURE
DOES NOT INCREASE THE TOTAL NUMBER OF AVAILABLE ZONES BEYOND 192. If one of the sixteen zones
must be a fire zone, it must be one of Zones 1 to 8. The corresponding upper zone will become unavailable. For
example: if Zone 6 is a fire zone, then Zone 14 will not be available. (See location 37, page 22)
Zone Types (Configurations) - The NX-8E has 30 programmable Zone Types that determine how each zone will
function and report. The default Zone Types are listed on page 18. (See locations 111-169, pages 33-37)
NX-8E CONTROL
7
IV.
PROGRAMMING THE LED KEYPADS
This section describes how to program the address and partition of each keypad as well as the options that are
available. The address of the keypad is important because this is how the panel supervises the keypads.
The factory default for the Master code is [1]-[2]-[3]-[4] when using a 4-digit code or [1]-[2]-[3]-[4]-[5]-[6] for a 6-digit
code. The factory default for the "Go To Program" code is [9]-[7]-[1]-[3] for a 4-digit code or [9]-[7]-[1]-[3]-[0]-[0] for a
6-digit code.
[r] [9] [2] (Applies to LED keypad ONLY)
1) Enter [r] [9] [2] [program code].
2) Enter the zone number (1 - 192) you want the keypad to start at.
3) Enter [r] to save and exit.
[r]-[9]-[3] Set keypad options
1) Enter [r]-[9]-[3] [program code]- The "Service" LED will flash.
2) LEDs 1-8 can now be toggled on/off to enable/disable the following functions:
3) After enabling/disabling the desired functions press [r]
LED
Keypad Feature Enabled
1
RESERVED.
DO NOT PROGRAM THIS AT ALL!
2
Enable Silent Keypad option. Silences the entry/exit sounder & chime only.
3
Enable Ding-Dong sound for Chime - If off, chime will be a single tone. (See location 40, page 23)
4
Enable Keypress Silence option
(silences the pulsing keypad sounder for 5 seconds when a key is pressed)
5
Enable Armed Status Suppression
(will not allow the keypad to display faulted or bypassed zones when the system is armed)
6
Enable Panic, Fire, Medical Beeptone
(will sound a short beep to verify that the keypress was accepted)
7
Suppresses the "Service" LED (NOTE: For UL installations, the Service LED shall not be suppressed.)
(will not allow the "Service" LED to illuminate for any reason. If there is a system trouble, pressing [r]-[2]
will still show the service menu.)
8
Enable multi-partition viewing
(enables temporary viewing of all partitions by pressing [r]-[1]-[partition number])
[r]-[9]-[4] Set Keypad Number and Partition
1) Enter [r]-[9]-[4]-[program code]- The "Service" LED and the "Instant" LED will flash.
2) Enter the keypad number (1-8)
3) Press [r]- The "Instant" LED will illuminate steady and the "Service" LED will remain flashing.
4) Enter the partition number for the keypad (The keypad will automatically exit this mode at this time)
[r]-[9]-[5] Set elapsed increments since last autotest
1) Enter [r]-[9]-[5]-[program code]-The "Service" LED will flash.
2) Enter [100's digit] -[10's digit]-[1's digit]-[#]
[r]-[9]-[6] Set system date
1) Enter [r]-[9]-[6]-[master code]. The "Service" LED will flash.
2) Enter [day of week (1=Sun)]-[month 10's digit]-[month 1's digit]-[day 10's digit]
[day 1's digit] -[year 10's digit]-[year 1's digit]
[r]-[9]-[7] Set system clock
1) Enter [r]-[9]-[7]-[master code]. The "Service" LED will flash.
2) Enter [hour 10's digit]-[hour 1's digit]-[minutes 10's digit]-[minutes 1's digit]
8
NX-8E CONTROL
CHANGING USER CODES:
1) Enter [r]-[5]-[master code] - The "Ready" LED will flash.
2) Enter the 3 digit user number (i.e. “003 for user 3). Maximum number of users is 240.
3) Enter the new user code designated for that individual - The "Ready" LED will flash indicating that the code
was accepted. If it rejects the code, the sounder will beep 3 times,
4) If another user code needs to be programmed, return to step 2.
5) Press [#] while the "Ready" LED is flashing to exit the User Code Programming Mode.
ASSIGNING AUTHORITY LEVEL:
1) Enter [r]-[6]-[master code] - The "Ready" LED will flash.
2) Enter [3 digit user number] (always 3 digits such as “003” for user 3) - The "Ready" LED will illuminate
steady and the "Instant" LED will flash. Refer to the chart below for the description of each LED. Turn the
LED on for the features that you desire.
LED
ATTRIBUTES IF LED 8 IS OFF
LED
ATTRIBUTES IF LED 8 IS ON
1
Reserved
1
Activate output #1
2
Arm Only
2
Activate output # 2
3
Arm Only After Close Window
3
Activate output # 3
4
Master arm/disarm (can program other codes)
4
Activate output # 4
5
Arm/disarm code
5
Arm/disarm
6
Allowed to bypass zones (see location 23)
6
Bypass Zones
7
Code will send open / close reports
7
Open / Close Reporting
8
If this LED is on, LEDs 1-7 will use the chart to the right
8
If this LED is off, LEDs 1-7 use the chart to the left
3) Enter [r] - The "Instant" LED will illuminate steady.
This moves you to the partition enable. (This tells the system what partition this user can arm/disarm.
LEDs 1-8 illuminate for each partition that the user has authorization for. To change any of these
numbers, press 1-8 to permit or deny access to the user. (Example: If LED #2 is lit, then user has
assigned access to that partition. By pressing the [2] key, the LED will go off indicating the user has
been denied access to that partition.)
4) Enter [r]
This returns you back to step 2 above. At this point you may enter another user number to assign
attributes for. You may continue this procedure until you have assigned authority levels to all user
numbers - or - you may press [#] key to exit the Assigning Authority Level Program.
NOTE: Any master arm/disarm code can add or change a user code if the master code has access to the
same partitions as the code being added/changed. Consequently, when programming the user codes
for a partitioned system, leave at least one code (can be "go to program code" if enabled in location
43) access to all partitions or you will not be able to add new users. If you desire the end user to be
able to add new codes, you must remove the partition authority from all blank codes.
[r]-[9]-[8]
Pressing [r]-[9]-[8] while the system is disarmed will cause the control to do a callback for a download.
NOTE: A valid user code may be required after [r]-[9]-[8] if enabled in location 41, page 23.
[r]-[9]-[9]
Pressing [r]-[9]-[9] while the system is disarmed will cause the control panel to seize the phone line for a
download. NOTE: A valid user code may be required after [r]-[9]-[9] if enabled in location 41.
NX-8E CONTROL
9
V.
PROGRAMMING THE CONTROL
ENTERING THE PROGRAM MODE
To enter the Program Mode, press [r]-[8]. At this time, the five function LEDs (Stay, Chime, Exit, Bypass, & Cancel)
will begin to flash. Next, enter the "Go To Program Code" (FACTORY DEFAULT IS [9]-[7]-[1]-[3]). If the "Go To
Program Code" is valid, the "Service" LED will flash and the five function LEDs will illuminate steady. You are now in
the Program Mode and ready to select the module to program.
SELECTING THE MODULE TO PROGRAM
Since all modules connected to the NX-8E are programmed through the keypad, the module you are programming
should be the first entry. To program the NX-8E Control Panel, enter [0]-[#]. The [0] is the module number of the
control and [#] is the entry key. Other module entry numbers can be found in their corresponding manuals.
PROGRAMMING A LOCATION
Once the number of the module to be programmed has been entered, the "Armed" LED will illuminate, indicating it is
waiting for a programming location to be entered. Any location can be accessed by directly entering the desired
programming location followed by [#]. If the location entered is a valid location, the "Armed" LED will extinguish, the
"Ready" LED will illuminate and the binary data for the first segment of this location will be shown by the zone LED's.
While entering new data, the "Ready" LED will begin flashing to indicate a data change in process. The flashing will
continue until the new data is stored by pressing [r]. Upon pressing [r], the keypad will advance to the next segment
and display its data. This procedure is repeated until the last segment is reached. Pressing the [#] key will exit from
this location, and the "Armed" LED will illuminate again waiting for a new programming location to be entered. If the
desired location is the next sequential location, press the [POLICE] key. If the previous location is desired press the
[FIRE] key. If the same location is desired press the [MEDIC] key. To review the data in a location, repeat the above
procedure, pressing [r] without any numeric data entry. Each time [r] is pressed, the programming data of the next
segment will be displayed for review.
EXITING A LOCATION
After the last segment of a location is programmed, pressing [r] will exit that location, turn the "Ready" LED off and
the "Armed" LED on. The [r] must be pressed or the data will not be saved. To exit before the last segment, press
[#]. As before, you are now ready to enter another programming location. If an attempt is made to program an invalid
entry for a particular segment, the keypad sounder will emit a triple error beep (beep, beep, beep), and remain in that
segment awaiting a valid entry.
EXITING THE PROGRAM MODE
When all the desired changes in programming have been made, it is time to exit the program mode. Pressing [Exit]
will exit this programming level, and go to the "Select a Module To Program" level. If no additional modules are to be
programmed, pressing [Exit] again will exit the program mode. If there is a module to be programmed, it may be
selected by entering its address followed by [#] (see "Selecting the Module To Program" above). The procedure for
programming these devices is the same as for the control panel, except the locations will be for the module selected.
10
NX-8E CONTROL
PROGRAMMING EXAMPLE TO BE INSERTED HERE.
NX-8E CONTROL
11
VI.
PROGRAMMING DATA
Programming data is always one of two types. One type of data is numerical and can take on values from 0 to 15 or 0
to 255 depending on the location's segment. The other type of data is a feature selection type. Feature selection data
is used to turn features on or off. Use the following procedures when working with these two data types:
NUMERICAL DATA
Numerical data is programmed by entering a number from 0-255 on the numeric keys of the system keypad. To view
the data in a location, a binary process is used. With this process, the LEDs for zones 1 through 8 are utilized, and
the numeric equivalents of their illuminated LEDs are added together to determine the data in a programming location.
The numeric equivalents of these LEDs are as follows:
Zone 1 LED = 1
Zone 5 LED = 16
Zone 2 LED = 2
Zone 6 LED = 32
Zone 3 LED = 4
Zone 7 LED = 64
Zone 4 LED = 8
Zone 8 LED = 128
Example: If the numerical data to be programmed in a location is "66", press [6]-[6] on the keypad. The LEDs for Zone
2 and Zone 7 will become illuminated indicating 66 is in that location (2 + 64 = 66). See this example on page 11.
Once the data is programmed, press [r] to enter the data and advance to the next segment of that location. After the
last segment of a location is programmed, press [r] to exit that location, turn the "Ready" LED off and the "Armed"
LED on. As before, you are now ready to enter another programming location. If an attempt is made to program a
number too large for a particular segment, the keypad sounder will emit a triple beep, indicating an error, and remain
in that segment awaiting a valid entry. On the LCD keypad, the number in the location will be displayed. For locations
with a maximum of 15, the hexadecimal equivalent will be displayed in parenthesis. Example: 11 (B) or 14 (E).
FEATURE SELECTION DATA
Feature selection data will display the current condition (on or off) of eight features associated with the programming
location and segment selected. Pressing a button on the touchpad (1 thru 8) that corresponds to the "feature number"
within a segment will toggle (on/off) that feature. Pressing any numeric key between [1] and [8] for selection of a
feature, will make the corresponding LED illuminate (feature ON). Press the number again, and the LED will extinguish
(feature OFF). You will see that numerous features can be selected from within one segment. For instance, if all eight
features of a segment are desired, pressing [1]-[2]-[3]-[4]-[5]-[6]-[7]-[8] will turn on LED's 1 thru 8 as you press the
keys, indicating that those features are enabled. LCD Keypad Users Note: The numbers of the enabled features will be
displayed. However, the features not enabled will display a hyphen (-). After the desired setting of features is selected
for this segment, press [r]. This will enter the data and automatically advance to the next segment of the location.
When you are in the last segment of a location and press [r] to enter the data, you will exit that location. This will now
turn the "Ready" LED off and the "Armed" LED on. As before, you are now ready to enter another programming
location.
VII.
LOADING FACTORY DEFAULTS
To load the factory defaults, enter the program mode using the procedure on page 9, then type [9]-[1]-[0]-[#]. The
keypad will beep 3 times indicating that the loading is in progress. The loading takes about 6 seconds.
VIII.
ENROLLING MODULES AND KEYPADS
For supervision purposes, the NX-8E has the ability to automatically find and store in its memory, the presence of all
keypads, zone expanders, wireless receivers, and any other module connected to the data terminal. This allows these
modules to be supervised by the control panel. To enroll the modules, enter the Program Mode of the NX-8E control
panel as described on page 9. When the Program Mode is exited, the NX-8E control will automatically enroll the
devices. The enrolling process takes about 12 seconds, during which time the "Service" LED will illuminate. User
codes will not be accepted during the enrolling process. If a speaker is attached to the NX-8E, it will click at this time.
If a siren or bell is attached to the NX-8E, it will sound for about 1 second. Once a module is enrolled, if it is not
detected by the control, the "Service" LED will illuminate.
IX.
L QUICK START INSTALLATION
For most routine installations, the "Quick Start" option will allow for enabling a majority of the options available with the
NX-8E, when communicating in Contact ID or SIA formats and without partitioning. The "Quick Start" locations can be
identified by the L symbol.
12
NX-8E CONTROL
X.
L
L
L
PROGRAMMING LOCATIONS
LOCATION 0 - PHONE NUMBER 1 (20 segments, numerical data)
The first telephone number is programmed in location 0. A "14" indicates the end of the phone number. Delays of four
seconds can be programmed at any point in the phone number by programming a "13" in the appropriate segment. If
tone dialing is desired, program a "15" in the segment where tone dialing should begin. If the entire number should be
tone dialing, program a "15" in the first segment. Program an A11" for a Ar@, and a A12" for a A#@.
LOCATION 1 - ACCOUNT CODE FOR THE PHONE #1 (6 segments, numerical data)
The account code sent when Phone #1 is dialed is programmed in location 1. Program a A10" in the segment
immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments.
LOCATION 2 - COMMUNICATOR FORMAT FOR PHONE #1 (1 segment, numerical data)
Location 2 contains the communicator format used to transmit to the receiver connected to Phone #1. Consult the
instructions for your central station receiver to determine which format is compatible. Select a format from Table X-1
COMMUNICATOR FORMAT SELECTIONS. If you require a format other than those listed, review the override
options described in location 18, to build the appropriate format. A "15" must be programmed in location 2 in addition
to the entries in location 18 in order to create a special format. If this location contains a "0", the built-in communicator
will be disabled, and the NX-8E will function as a local only control.
Table X-1 COMMUNICATOR FORMAT SELECTIONS
DATA
L
FORMAT
DESCRIPTION
0
Local
Communicator is disabled
1
Universal 4+2
Two digit event code 1800hz transmit 2300hz handshake double round parity
40pps
2
3+1 fast (or 4+1)
One digit event code 1900Hz transmit 1400Hz handshake double round parity
20pps
3
Reserved
Reserved
4
Pager
2 digit event code DTMF transmission
5
3/1 or 4/1 slow
1800hz transmit 2300hz handshake double round parity 20 p.p.s. hex capability
6
3/1 or 4/1 slow
1800hz transmit 1400hz handshake double round parity 20 p.p.s. hex capability
7
3/1 or 4/1 fast
1800hz transmit 2300hz handshake double round parity 40 p.p.s. hex capability
8
3/1 or 4/1 fast
1800hz transmit 1400hz handshake double round parity 40 p.p.s. hex capability
9
3/1 or 4/1 fast with parity
1800hz transmit 2300hz handshake single round w/parity 40 p.p.s. hex
capability
10
3/1 or 4/1 fast with parity
1800hz transmit 1400hz handshake single round w/parity 40 p.p.s. hex
capability
11
4+2 express
2 digit event code DTMF transmission
12
4+2 fast
Two-digit event code 1900hz transmit 1400hz handshake double round parity
20 p.p.s.
13
Ademco Contact ID
DTMF (see pages 69 & 70)
14
SIA
FSK (see pages 69 & 70)
15
Custom format
(See location 18, page 17)
LOCATION 3 - DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE # 1 (2 segments, numerical data)
Segment 1- Dial attempts: Location 3, Segment 1 is used to enter the number of dial attempts (1 to 15 Attempts) the
communicator will make to Phone #1 before ending the notification process. Factory default is "8" and the
communicator will make eight (8) attempts to the first number.
Segment 2- Phone #1 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-8E to
make the designated number of attempts to Phone #2 before setting the "Fail To Communicate" condition and stop
reporting. Programming a "1" in this segment will cause the NX-8E to stop trying to communicate after the designated
NX-8E CONTROL
13
number of attempts have been made to Phone #1. If a "2" is programmed in this segment, it will cause the NX-8E to
make the dial attempts in increments of two. The first two attempts will be made to Phone #1, the next two attempts to
Phone #2, then repeating until the total number of attempts designated in Segment 1 is completed.
REPORTING EVENTS TO PHONE NUMBER 1
Phone #1 has two programming locations that are used to select which events are reported to this phone number.
Location 4 is used to select which events are reported to Phone #1. Location 5 is used to select which partitions are
reported to Phone #1. If dual or split reporting is not desired, location 4 should be used to select all events to Phone
#1 and location 5 should be left at the factory default of "0". If dual or split reporting is desired, and the split is based
on the event type (such as alarm, open/close, etc.), location 4 should be used to select only those events that should
be reported to Phone #1 and location 5 should be left at the factory default of "0". If dual or split reporting is desired,
and the split is based on partition, location 4 should be programmed as a "0" and location 5 should be used to select
those partitions that should be reported to Phone #1. If no events should be reported to Phone #1, both locations
should be programmed as "0" (disabling all options).
LOCATION 4 - EVENTS REPORTED TO PHONE # 1 (2 segments, feature selection data)
Segment 1:
1 = Alarms and Alarm Restores.
2 = Opening and Closings.
3 = Zone Bypass and Bypass Restores.
4 = Zone Trouble and Trouble Restores.
5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.
6 = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore.
7 = Test Reports.
8 = Start and End programming, Download complete.
Segment 2:
1 = Zone and Box Tamper and Tamper Restore.
2 = Auxiliary Power Overcurrent, Ground Fault, and Restore for both.
3 = Wireless Sensor Missing and Restore.
4 = Wireless Sensor Low Battery and Restore.
5 = Expander Trouble and Restore.
6 = Fail To Communicate.
7 = Zone Activity Monitor.
8 = Reserved.
LOCATION 5 - PARTITIONS REPORTED TO PHONE #1 (1 segment, feature selection data)
Location 5 is used when events to be reported to a phone number are based upon the partition regardless of the
event. If this location is used, location 4 should be programmed as "0".
Segment 1:
L
L
1 = Partition #1
2 = Partition #2
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 6 - PROGRAMMING PHONE #2 (20 segments, numerical data)
Phone #2 is programmed in location 6. A "14" indicates the end of the phone number. Delays of four seconds can be
programmed at any point in the phone number by programming a "13" in the appropriate segment. If tone dialing is
desired, program a "15" in the segment where tone dialing should begin. If the entire number should be tone dialing,
program a "15" in the first segment. Program an A11" for a Ar@, and a A12" for a A#@.
LOCATION 7 - ACCOUNT CODE FOR THE PHONE #2 (6 segments of numerical data)
The account code sent when Phone #2 is dialed is programmed in location 7. Program a A10" in the segment
immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments. If
this location is left unprogrammed, account code 1 will be used when the second phone number is dialed.
14
NX-8E CONTROL
L
LOCATION 8 - COMMUNICATOR FORMAT FOR PHONE # 2 (1 segment, numerical data)
Location 8 contains the communicator format used to transmit to the receiver connected to Phone #2. Consult the
instruction manual for your central station receiver to determine which format is compatible, and select from Table X-1
COMMUNICATOR FORMAT SELECTIONS on page 13. If you require a format other than those listed, review the
override options described in Location 18 to build the appropriate format. A "15" must be programmed in location 8 in
addition to the entries in location 18 in order to create a special format. If this location contains a "0", format 1 will be
used when Phone #2 is dialed.
LOCATION 9 - DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE #2 (2 segments, numerical data)
Segment 1, Dial attempts: Segment 1 of Location 9 is used to enter the number of dial attempts (1 to 15 attempts)
the communicator will make to Phone #2 before ending the notification process. Factory default is "8" and the
communicator will make the same number of attempts as those programmed in location 3.
Segment 2, Phone #2 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-8E to
make the designated number of attempts to Phone #1 before setting the "Fail To Communicate" condition and stop
reporting. Programming a "1" in this segment will cause the NX-8E to stop trying to communicate after the designated
number of attempts have been made to Phone #2. If a "2" is programmed in this segment, it will cause the NX-8E to
make the dial attempts in increments of two. The first two attempts will be made to Phone #2, the next two attempts to
Phone #1, then repeating until the total number of attempts designated in Segment 1 is completed.
REPORTING EVENTS TO PHONE NUMBER 2
Phone #2 can be used to back up Phone #1 or for a second receiver to multi-report or split report events. Phone #2
has two programming locations that are used to select which events are reported to this phone number. Location 10 is
used to select which events are reported to Phone #2, and location 11 is used to select which partitions are reported
to Phone #2. If dual or split reporting is not desired, location 10 and location 11 should be left at the factory default of
"0". If multi-reporting or split reporting is desired, and the split is based on the event type (such as alarm, open close
etc.), location 10 should be used to select only those events that should be reported to Phone #2, and location 11
should be left at the factory default of "0". If dual or split reporting is desired, and the split is based on partition, then
location 10 should be programmed as "0", and location 11 should be used to select those partitions that should be
reported to the Phone #2. If no events should be reported to Phone #2, both locations should be "0".
LOCATION 10 - EVENTS REPORTED TO PHONE #2 (2 segments of feature selection data)
Segment 1:
1 = Alarms and Alarm Restores.
2 = Opening and Closings.
3 = Zone Bypass and Bypass Restores.
4 = Zone Trouble and Trouble Restores.
5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.
6 = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore.
7 = Test Reports.
8 = Start and End programming, Download complete.
Segment 2:
1 = Zone and Box Tamper and Tamper Restore.
2 = Auxiliary Power Overcurrent and Ground Fault and Restore for both.
3 = Sensor Missing and Restore.
4 = Sensor Low Battery and Restore.
5 = Expander Trouble and Restore.
6 = Fail To Communicate.
7 = Zone Activity Monitor.
8 = Reserved.
NX-8E CONTROL
15
LOCATION 11 - PARTITIONS REPORTED TO PHONE #2 (1 segment, feature selection data)
Location 11 is used when events to be reported to a phone number are based upon the partition regardless of the
event. If this location is used, location 10 should be "0".
Segment 1:
1 = Partition #1
2 = Partition #2
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 12 - PROGRAMMING PHONE #3 (20 segments, numerical data)
Phone #3 is programmed in location 12. A "14" indicates the end of the phone number. Delays of four seconds can
be programmed at any point in the phone number by programming a "13" in the appropriate segment. If tone dialing is
desired, program a "15" in the segment where tone dialing should begin. If the entire number should be tone dialing,
program a "15" in the first segment. Program an A11" for a Ar@, and a A12" for a A#@.
LOCATION 13 - ACCOUNT CODE FOR PHONE #3 (6 segments, numerical data)
The account code sent when Phone #3 is dialed is programmed in location 13. Program a A10" in the segment
immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments. If
location 6 is left unprogrammed, account code 1 will be used when the Phone #3 is dialed.
LOCATION 14 - COMMUNICATOR FORMAT FOR PHONE #3 (1 segment, numerical data)
Location 14 contains the communicator format used to transmit to the receiver connected to phone #3. Consult the
instruction manual for your central station receiver to determine which format is compatible, and select from Table X-1
COMMUNICATOR FORMAT SELECTIONS on page 13. If you require a format other than those listed, review the
override options described in Location 18 to build the appropriate format. A "15" must be programmed in location 14
in addition to the entries in location 18 in order to create a special format. If this location contains a "0", format 1 will
be used when Phone #3 is dialed.
LOCATION 15 - DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE #3 (2 segments, numerical data)
Segment 1, Dial Attempts: Segment 1 of Location 15 is used to enter the number of dial attempts (1 to 15 attempts)
the communicator will try to Phone #3 before ending the notification process. Factory default is "8" and the
communicator will make the same number of attempts as those programmed in location 3.
Segment 2, Phone # 3 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-8E to
make the designated number of attempts to Phone #2 before setting the "Fail To Communicate" condition and stop
reporting. Programming a "1" in this segment will cause the NX-8E to stop trying to communicate after the designated
number of attempts have been made to Phone #3. If a "2" is programmed in this segment, it will cause the NX-8E to
make the dial attempts in increments of two. The first two attempts will be made to Phone #3, the next two attempts to
Phone #2, then repeating until the total number of attempts designated in Segment 1 is completed.
REPORTING EVENTS TO PHONE NUMBER 3
Phone #3 can be used for a third receiver to multi-report or split report events. Phone #3 has two programming
locations that are used to select which events are reported to this phone number. Location 16 is used to select which
events are reported to Phone #3, and Location 17 is used to select which partitions are reported to Phone #3. If dual
or split reporting is not desired, location 16 and location 17 should be left at the factory default of "0". If multireporting or split reporting is desired and the split is based on the event type (such as alarm, open/close, etc.), then
location 16 should be used to select only those events that should be reported to Phone #3 and location 17 should be
left at the factory default of "0". If dual or split reporting is desired, and the split is based on partition, then location 16
should be programmed to "0" and location 17 should be used to select those partitions that should be reported to
Phone #3. If no events should be reported to Phone #3, both locations should be "0".
16
NX-8E CONTROL
LOCATION 16 - EVENTS REPORTED TO PHONE #3 (2 segments, feature selection data)
Segment 1:
1 = Alarms and Alarm Restores.
2 = Opening and Closings.
3 = Zone Bypass and Bypass Restores.
4 = Zone Trouble and Trouble Restores.
5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.
6 = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore.
7 = Test Reports.
8 = Start and End programming, Download complete.
Segment 2:
1 = Zone and Box Tamper and Tamper Restore.
2 = Auxiliary Power Overcurrent and Ground Fault and Restore for both.
3 = Sensor Missing and Restore.
4 = Sensor Low Battery and Restore.
5 = Expander Trouble and Restore.
6 = Fail To Communicate.
7 = Zone Activity Monitor.
8 = Reserved.
LOCATION 17 - PARTITIONS REPORTED TO PHONE #3 (1 segment, feature selection data)
Location 17 is used when events to be reported to a phone number are based upon the partition regardless of the
event. If this location is used, location 16 should be "0".
Segment 1:
1 = Partition #1
2 = Partition #2
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 18 - CUSTOM COMMUNICATOR FORMAT (See locations 2, 8, &14)
Segment 1:
1 = On for 1800hz transmit; Off for 1900hz.
2= On for 2300hz handshake; Off for 1400hz.
3= On for cksum parity; Off for double round parity.
4= On for 2 digit event code; Off for 1 digit event code.
5= Reserved.
6= Reserved.
7= On for 20 p.p.s.; Off for 10 or 40 p.p.s.
8= On for 10 p.p.s.; Off for 20 or 40 p.p.s.
Segment 2:
1= On for pager format (no handshake required).
2= On for 1400/2300 handshake.
3= Reserved
4= Reserved.
5= On for Contact ID.
6= On for SIA.
7= On for Contact ID or 4+3.
8= On for DTMF.
Segment 3 & 4: Reserved.
L
L
LOCATION 19 - DOWNLOAD ACCESS CODE (8 segments, numerical data)
Location 19 contains the eight-digit access code the NX-8E must receive from the downloading software before the
panel will permit downloading to occur. The factory default code is 84800000.
LOCATION 20 - NUMBER OF RINGS TO ANSWER (1 segment, numerical data)
Location 20 contains the number of rings to answer for a download. Enter a number from A0" (disabled) to "15".
Factory default is "8" and the NX-8E will answer on 8 rings.
NX-8E CONTROL
17
L
L
L
LOCATION 21 - DOWNLOAD CONTROL (1 segment, feature selection data)
Location 21 contains the feature selections for the controlling of download sessions. The following features can be
enabled or disabled using this location. (See the feature definitions beginning on page 3)
Segment 1:
1On enables two call answering machine defeat.
2On enables tone sniff answering machine defeat.
3On requires call back before download session.
4Shutdown (can only be viewed from the keypad, must be changed through downloading).
5On locks all local programming. (can only be viewed from the keypad, must be changed through
downloading)
6On locks programming of all locations associated with the communicator (can only be viewed from the
keypad, must be changed through downloading)
7On locks out download section. (can only be viewed from the keypad, must be changed through
downloading. If "On", locations 19 - 22 cannot be viewed from the keypad; can only be viewed
from the keypad when "Off".)
8On enables call back at auto test interval.
LOCATION 22 - DOWNLOAD CALL BACK NUMBER (20 segments, numerical data)
If a telephone number is programmed into this location, and "Require Callback" is enabled in location 21, the control
panel will hang up for approximately 36 seconds (ensuring that the calling party has disconnected), and then call
back. If tone dialing is desired, program an "15" in the segment where tone dialing should begin. If the entire number
should be tone dialing, program an A15" in the first segment. Four-second delays can be obtained anywhere in the
sequence by programming a "13" in the appropriate delay location. WARNING: THE CALLBACK PHONE NUMBER
SHOULD ALWAYS BE REVIEWED FOR ACCURACY BEFORE DISCONNECTING.
LOCATION 23 - PARTITION 1, FEATURE AND REPORT SELECTIONS (5 segments, feature selection data)
Location 23 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in location 23. Each of these features can be enabled
by partition. For additional partition information see locations 88-109 on pages 30-32. If the feature selection
location for any partition is left blank, that partition will use this location for the feature selection.
This location contains 3 segments of 8 features each. (See the feature definitions beginning on page 3.)
18
Segment 1:
1 - On enables the Quick Arm feature.
2 - On enables the Re-exit feature.
3 - On enables the Automatic Bypass feature.
4 - On enables the Silent Keypad Panic feature (overrides the audible panic selection).
5 - On enables the Audible Keypad Panic feature.
6 - On enables the Keypad Aux 1 feature (FIRE).
7 - On enables the Keypad Aux 2 feature (MEDICAL).
8 - On enables the Keypad Multiple Code Attempt Tamper feature.
Segment 2:
1 - On enables the LED Extinguish feature.
2 - On enables the Require Code for Bypassing feature.
3 - On enables the Zone Bypassed Sounder Alert feature.
4 - On enables the AC Power/Low Battery Sounder Alert feature.
5 - On enables Bypass toggle.
6 - On enables Silent Auto Arm.
7 - On enables the Automatic Instant feature.
8 – On enables Instant mode. (Applies to NX1208E / NX1248E)
Segment 3:
1 - On enables Opening and Closing reports.
2 - On enables Zone Bypass reporting.
3 - On enables Zone Restore reporting.
4 - On enables Zone Trouble reporting.
5 - On enables Zone Tamper reporting.
6 - On enables the Cancel reporting.
7 - On enables the Recent Closing report.
8 - On enables the Exit Error report.
NX-8E CONTROL
L
Segment 4:
1 – On enables Late to Close / Early to Open.
2 – On enables Auto Arm in Stay Mode.
3 – On disables the door delays in Night mode. (Applies to NX1208E / NX1248E)
4 - 8 Reserved.
Segment 5:
Reserved
LOCATION 24 - ENTRY / EXIT TIMERS (6 segments, numerical data)
Location 24 is used to program the Entry/Exit times. There are 2 separate Entry/Exit times.
Segment 1,
Entry time 1: This is the entry time that will be used when a delay 1 zone type initiates an entry
delay. Valid entries are 10-255 seconds.
Segment 2, Exit time 1: This is the exit time that will be used for all zones designated as delay 1. Valid entries
are 10-255 seconds.
Segment 3, Entry time 2: This is the entry time that will be used when a delay 2 zone type initiates an entry
delay. Valid entries are 10-255 seconds.
Segment 4, Exit time 2: This is the exit time that will be used for all zones designated as delay 2. Valid entries
are 10-255 seconds.
Segments 5 & 6
Reserved.
XI.
DEFAULT ZONE TYPES (Configurations)
Zones can be programmed to be one of thirty different zone types (configurations). Zone types # 17 - 20 can be used
for wireless or hardwired zones using European double EOL configuration. The default zone types are listed below.
These zone types can be customized by programming locations 110-169.
DATA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
DESCRIPTION OF DEFAULT ZONE TYPES
DAY ZONE - Instant when system is armed trouble zone when system is disarmed.
24-HOUR AUDIBLE - Creates an instant yelping siren alarm regardless of the armed state of the control
panel.
ENTRY/EXIT DELAY 1- A trip will start entry delay 1. The lack of a trip during exit delay will enable the
Automatic Bypass or Instant mode if so programmed.
FOLLOWER WITH AUTO- BYPASS DISABLED - This zone will be instant when the system is armed and no
entry or exit delays are being timed. It is delayed during entry and exit delay 1 times. This zone will not
automatically bypass even if enabled in Segment 1 of Location 23.
INTERIOR FOLLOWER WITH AUTO- BYPASS ENABLED - This zone will be instant when the system is
armed and no entry or exit delay is being timed. It is delayed during entry and exit delay 1 times. This zone will
automatically bypass if enabled in Segment 1 of Location 23.
INSTANT - This zone creates an instant alarm whenever it is tripped and the Armed LED is on.
24-HOUR SILENT - Creates an instant silent alarm regardless of the armed state of the control panel. It will
not display on the keypad.
FIRE - This zone will light the Fire LED and sound the temporal siren each time the zone is shorted. It will also
rapidly flash the Fire LED indicating a trouble if the zone is open.
ENTRY/EXIT DELAY 2- A trip will start entry delay 2. The lack of a trip during exit delay will enable the
Automatic Bypass or Instant mode if so programmed.
24-HOUR SILENT SUPERVISED- Creates an instant silent alarm regardless of the armed state of the control
panel. It will display on the keypad.
KEYSWITCH ZONE - This zone type will arm and disarm the partition or partitions of the control panel that it
resides in each time the zone is shorted. Keyswitch arming will report as user #99.
INTERIOR FOLLOWER WITH "CROSS ZONE" ENABLED - This zone will be instant when the system is
armed and no entry or exit delay is being timed. It is delayed during entry and exit delay times. If a "Cross
Zone" is not being timed it will start a "Cross Zone" timer. If a "Cross Zone" is being timed it will create an
instant alarm. This zone will automatically bypass when enabled in Segment 1 of Location 23.
INSTANT ENTRY GUARD - This zone creates an instant alarm whenever it is tripped and the Stay LED is off.
It will start an entry delay time 2 if it is tripped and the system is armed and the Stay LED is on.
ENTRY/EXIT DELAY 1 WITH GROUP BYPASS ENABLED - A trip will start entry delay 1. This zone will
bypass when the "Group Bypass" command is entered at the keypad. The lack of a trip during exit delay will
enable the Automatic Bypass or Instant mode if so programmed.
NX-8E CONTROL
19
DATA
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
L
DESCRIPTION OF DEFAULT ZONE TYPES
INTERIOR FOLLOWER WITH GROUP BYPASS ENABLED - This zone will be instant when the system is
armed and no entry or exit delays are being timed. It is delayed during entry/exit delay times. This zone will
bypass when the "Group Bypass" command is entered at the keypad. This zone will automatically bypass if
enabled in Segment 1 of Location 23.
INSTANT WITH GROUP BYPASS ENABLED - This zone creates an instant alarm whenever it is tripped and
the Armed LED is on. This zone will bypass when the "Group Bypass" command is entered at the keypad.
ENTRY/EXIT DELAY 1 WITH TAMPER ENABLED- A trip will start entry delay 1. The lack of a trip during exit
delay will enable the Automatic Bypass or Instant mode if so programmed. This zone type can be used to
enable tamper on a wireless transmitter.
INTERIOR FOLLOWER WITH TAMPER AND AUTO-BYPASS ENABLED - This zone will be instant when
the system is armed and no entry or exit delay is being timed. It is delayed during entry and exit delay times.
This zone will automatically bypass if enabled in Segment 1 of Location 23. This zone type can be used to
enable tamper on a wireless transmitter.
INSTANT WITH TAMPER ENABLED - This zone creates an instant alarm whenever it is tripped and the
Armed LED is on. This zone type can be used to enable tamper on a wireless transmitter.
ENTRY/EXIT DELAY 2 WITH TAMPER ENABLED-A trip will start entry delay 2. The lack of a trip during exit
delay will enable the Automatic Bypass or Instant mode if so programmed. This zone type can be used to
enable tamper on a wireless transmitter.
GAS DETECTION- Creates an instant alarm regardless of the armed state of the control panel. It will display
on the keypad and activate the keypad sounder.
LOW TEMP DETECTION- Creates an instant silent alarm regardless of the armed state of the control panel. It
will display on the keypad and activate the keypad sounder.
HIGH TEMP DETECTION- Creates an instant silent alarm regardless of the armed state of the control panel. It
will display on the keypad and activate the keypad sounder.
MANUAL FIRE - This zone will illuminate the Fire LED and sound the temporal siren each time the zone is
shorted. It will also rapidly flash the Fire LED indicating a trouble if the zone is open.
CHIME ONLY - Creates no alarm regardless of the armed state of the control panel. It will chime anytime it is
faulted and will display on the keypad. Local only.
INTERIOR FOLLOWER DELAY 2 - This zone will be instant when the system is armed and no entry or exit
delay is being timed. It is delayed during entry and exit delay 2 times. This zone will automatically bypass if
enabled in Segment 1 of Location 23.
INTERIOR FOLLOWER FORCE ARMABLE - This zone will be instant when the system is armed and no
entry or exit delay is being timed. It is delayed during entry and exit delay 1 times. This zone will automatically
bypass if enabled in Segment 1 of Location 23.
ENTRY/EXIT FORCE ARMABLE DELAY 2 - A trip will start entry delay 2. The lack of a trip during exit delay
will enable the Automatic Bypass or Instant mode if so programmed.
INTERIOR FOLLOWER WITH ACTIVITY SUPERVISION ENABLED - This zone will be instant when the
system is armed and no entry or exit delay is being timed. It is delayed during entry and exit delay times. It will
send a report if the zone activity time is reached without a change of state. Refer to Location 40 / Segment 11.
This zone will automatically bypass if enabled in Segment 1 of Location 23.
ENTRY/EXIT WITH ACTIVITY SUPERVISION ENABLED- A trip will start entry delay 1. It will send a report if
the zone activity time is reached without a change of state. Refer to Location 40 / Segment 11. The lack of a
trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed.
LOCATION 25 - ZONES 1-8 ZONE TYPE (8 segments, numerical data)
Location 25 contains the Zone Type for zones 1-8. Segment 1 is for zone 1, and Segment 8 is for zone 8.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 26 - PARTITION SELECT, ZONES 1-8 (8 segments, feature selection data)
Location 26 is used to select the partition(s) that zones 1 - 8 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions
are armed. A zone that resides in more than 1 partition will be reported to its lowest partition number.
Location 26 has 8 segments. Segment 1 corresponds to zone 1, and Segment 8 corresponds to zone 8.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
20
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
NX-8E CONTROL
L
LOCATION 27 - ZONES 9-16 ZONE TYPE (8 segments, numerical data)
Location 27 contains the Zone Type for zones 9 -16. Segment 1 is for zone 9; Segment 8 is for zone 16.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 28 - PARTITION SELECT, ZONES 9-16 (8 segments, feature selection data)
Location 28 is used to select the partition(s) that zones 9-16 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions
are armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Location
28 has 8 segments. Segment 1 corresponds to zone 9 and Segment 8 corresponds to zone 16.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 29 - ZONES 17-24 ZONE TYPE (8 segments, numerical data)
Location 29 contains the Zone Type for zones 17-24. Segment 1 is for zone 17; Segment 8 is for zone 24.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 30 - PARTITION SELECT, ZONES 17-24 (8 segments, feature selection data)
Location 30 is used to select the partition(s) that zones 17-24 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions
are armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Location
30 has 8 segments. Segment 1 corresponds to zone 17 and Segment 8 corresponds to zone 24.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 31 - ZONES 25-32 ZONE TYPE GROUP (8 segments, numerical data)
Location 31 contains the Zone Type for zones 25-32. Segment 1 is for zone 25; Segment 8 is for zone 32.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 32 - PARTITION SELECT, ZONES 25-32 (8 segments, feature selection data)
Location 32 is used to select the partition(s) that zones 25-32 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition it will only be active when all partitions
are armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 25 and Segment 8 corresponds to zone 32.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 33 - ZONES 33-40 ZONE TYPE (8 segments, numerical data)
Location 33 contains the Zone Type for zones 33-40. Segment 1 is for zone 33 Segment 8 is for zone 40.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 34 - PARTITION SELECT, ZONES 33-40 (8 segments of feature selection data)
Location 34 is used to select the partition(s) that zones 33-40 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions
are armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 33 and Segment 8 corresponds to zone 40.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
NX-8E CONTROL
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
21
L
LOCATION 35 - ZONES 41-48 ZONE TYPE (8 segments of numerical data)
Location 35 contains the Zone type for zones 41-48. Segment 1 is for zone 41 Segment 8 is for zone 48.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 36 - PARTITION SELECT, ZONES 41-48 (8 segments, feature selection data)
Location 36 is used to select the partition or partitions that zones 41-48 reside in. A zone may reside in any
combination of the 8 partitions. If a burglary zone resides in more than 1 partition it will only be active when
all partitions are armed. A zone that resides in more than 1 partition will be reported to its lowest
partition. Location 36 has 8 segments. Segment 1 corresponds to zone 41 and Segment 8 corresponds to zone
48.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
22
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 37 - SIREN AND SYSTEM SUPERVISION (7 segments, feature selection data)
Location 37 is used to enable various system feature and reporting options. (Refer to the feature definitions.)
Segment 1:
1 - On if siren sounds for "Telephone Line Cut" when armed.
2 - On if siren sounds for "Telephone Line Cut" when disarmed.
3 - On if siren blast at arming.
4 - On if siren blast at exit expiration.
5 - On if siren blast at closing kissoff.
6 - On if siren sounds during a "Cross Zone" verification time.
7 - On if siren sounds for a Zone or Box Tamper.
8 - On if siren blasts 1 time for keyswitch or wireless arming; 2 times for disarming.
Segment 2:
1 - On if siren driver should be a voltage output. Off if on board siren driver enabled.
2 - On if siren sounds for expander trouble (required for UL installations).
3 - On for Immediate Restore by zone. Off for zones to restore only when siren is off.
4 - On if Dynamic Battery Test performed at arming. Off if performed at disarming. (See location
40)
5 - On if Battery Missing Test is performed every 12 seconds.
6 - On if Manual Bell Test performed during [r]-[4]-[4] test function.
7 - On if Manual Communicator Test performed during [r]-[4]-[4] test function.
8 - On if Box Tamper terminals on the control panel are enabled.
Segment 3:
1 - On if Box Tamper report enabled.
2 - On if AC Fail reporting enabled.
3 - On if Low Battery reporting enabled.
4 - On if Aux. Power Overcurrent report enabled.
5 - On if Siren Supervision report enabled.
6 - On if Telephone Line Cut report enabled.
7 - On if Ground Fault Detection report enabled.
8 - On if Expander Trouble reporting enabled.
Segment 4:
1 - On if Fail To Communicate report enabled.
2 - On if Log Full report enabled.
3 - On if Autotest report enabled.
4 - On if Start/End programming report enabled.
5 - On if End Download report enabled.
6 - On if Sensor Low Battery report enabled.
7 - On if Sensor Missing report enabled.
8 - Reserved.
Segment 5:
1 = On enable Lost Clock service light.
2 = On enables Zone Doubling (requires NX-200 Zone Doubling Kit).
3 = On disables On-Board 8 zones.
4 = On will allow two trips on same cross-zone to activate an alarm.
5 = On will not allow zones that are force armed to report bypass.
6 = On enables Silent Exit option.
7 = Use internal crystal for clock.
8 = Disable Temporal Siren on Fire. NOTE: Do NOT disable for UL listed systems.
NX-8E CONTROL
L
L
L
Segment 6:
1 = Enable 2 wire smoke.
2 = Reserved.
3 = Enable for Zone Activity in Hours (not Days)
4 = Enable Daylight Savings Time (DST)
5 = Reserved
6 = On to disable Clean Me report (Clean Me report is enabled at default)
7-8 = Reserved.
Segment 7:
Reserved
LOCATION 38 - SWINGER SHUTDOWN COUNT
Location 38 contains the number of trips during an arming cycle that the NX8 will allow before bypassing a zone.
The count determination is described in the feature definitions beginning on page 3. NOTE: For UL
installations, this feature shall be disabled.
.
LOCATION 39 - KEYPAD SOUNDER CONTROL (1 segment, feature selection data)
Segment 1:
1 - On if keypad sounds for ATelephone Line Cut@ when the system is armed.
2 - On if keypad sounds for ATelephone Line Cut@ when disarmed.
3 - On if keypad sounds upon AC Power Failure.
4 - On if keypad sounds when a Low Battery is detected.
5 - On if keypad sounds during Cross Zone trip time.
6 - On if keypad sounds for zone and box tampers.
7 - Reserved.
8 - On if keypad sounds for expander trouble (required for UL installations).
LOCATION 40 - SYSTEM TIMERS (14 segments, numerical data)
Location 40 contains the duration of various system timing functions. Example: If you desire the duration of the
Dynamic Battery Test to be 30 minutes, you should program [3]-[0]-[r] in segment 1 of this location. The [3]-[0]
is the number of minutes, and the [r] stores the data and moves to the next segment of this location.
Segment 1 Segment 2 Segment 3 Segment 4 Segment 5 Segment 6 Segment 7 -
Dynamic Battery Test duration in minutes 0-255 minutes ("0" = no test)
AC Fail report delay in minutes 0-255 minutes.
Power Up Delay in seconds 0-60 seconds ("0" = no power up delay).
Siren Time in minutes 1-255 minutes.
Telephone Line Cut delay in seconds 0-255 seconds ("0" = no TLM).
Cross Zone time in minutes 0-255 ("0" = no cross zoning).
Chime time in 50 mS (1/20th second) increments from 0-12 seconds ("0" = follows zone 255
latched).
Segment 8 - Dial delay in seconds 0-255 seconds (“0 ” = no abort delay).
Segment 9 - Fire Alarm Verification time in seconds 120-255 seconds ("0" = no fire alarm verification).
NOTE: This feature is not approved for residential use in California
Segment 10 -Listen-In time in seconds 0-255 ("0" = no Listen-In time).
Segment 11 –Zone Activity Monitor feature timed in days 0 – 255 (“0” = disabled)
Segments 12-14 Reserved.
Note: The "Listen-In" feature cannot be enabled for UL Listed systems. The "Dynamic Battery
Test" feature cannot exceed four (4) hours. The dial delay shall be set to -0-.
LOCATION 41 - SPECIAL FEATURES (1 segment, feature selection data)
Segment 1:
1On enables the 6-digit code option. If 6-digit option is enabled, all arm/disarm codes and the "Go To
Program Code" are 6 digits. If this option is enabled, the default user 1 code is [1]-[2]-[3]-[4]-[5]-[6].
NOTE: IF YOU ENABLE THIS OPTION, VERIFY THAT THE "GO TO PROGRAM CODE" IS A SIXDIGIT CODE BEFORE EXITING PROGRAMMING.
2On requires code entry for [r]-[9]-[8] (perform call back download) and [r]-[9]-[9] (answer incoming
call for download) functions.
3Enable Auto Cancel / Abort (Refer to feature definitions beginning on page 3)
4Enable Walk-Test Mode (Refer to feature definitions beginning on page 3)
5-8 Reserved.
NX-8E CONTROL
23
L
LOCATION 42 - GO TO PROGRAM CODE (6 segments, numerical data)
Location 42 contains the "Go To Program Code". This location contains either a 4 or 6-digit code. If the 6-digit
code option is enabled in Location 41, THIS CODE MUST CONTAIN SIX (6) DIGITS. If this option is not
enabled in location 41, the last 2 segments (digits) will be ignored. With the NX-8E disarmed, the "Go To
Program Code" can be used to enter the Program Mode.
LOCATION 43 - GO TO PROGRAM CODE PARTITION AND AUTHORIZATION (2 segments, feature
selection)
The "Go To Program Code" can be used as a standard arm/disarm code. When using the code to arm or disarm,
the user ID is 255. (This code may not be changed in the Run Mode.)
L
Segment 1:
1 - Reserved.
2 - On enables "Go To Program Code" as an arm only code.
3 - On enables "Go To Program Code" as an arm only after closing.
4 - On enables "Go To Program Code" as a master arm/disarm code (can change user codes)
5 - On enables "Go To Program Code" as an arm/disarm code.
6 - On enables "Go To Program Code" to bypass zones.
7 - On enables "Go To Program Code" opening and closing reports.
8 - Reserved.
Segment 2:
1 - On enables the "Go To Program Code" for Partition #1.
2 - On enables the "Go To Program Code" for Partition #2.
3 - On enables the "Go To Program Code" for Partition #3.
4 - On enables the "Go To Program Code" for Partition #4.
5 - On enables the "Go To Program Code" for Partition #5.
6 - On enables the "Go To Program Code" for Partition #6.
7 - On enables the "Go To Program Code" for Partition #7.
8 - On enables the "Go To Program Code" for Partition #8.
LOCATION 44 - DURESS CODE (6 segments, numerical data)
Location 44 contains the "Duress" code. This Location contains either 4 or 6 digits. If the 6-digit code option is
enabled in Location 41, THIS CODE MUST CONTAIN SIX (6) DIGITS. If the 6-digit option is not enabled in
location 41, the last 2 digits will be ignored. If the duress code is programmed, it will work for all partitions.
LOCATION 45 - AUXILIARY OUTPUT 1-4 PARTITION SELECTION (4 segments, feature selection data)
Location 45 is used to select which partition(s) the events must occur in before the output will activate. Location
45 has 4 segments. Segment 1 corresponds to output 1, and Segment 4 corresponds to output 4.
Segment 1 (Aux 1)
1= Partition #1
2= Partition #2
3= Partition #3
4= Partition #4
5= Partition #5
6= Partition #6
7= Partition #7
8= Partition #8
Segment 2 (Aux 2)
1= Partition #1
2= Partition #2
3= Partition #3
4= Partition #4
5= Partition #5
6= Partition #6
7= Partition #7
8= Partition #8
Segment 3 (Aux 3)
1= Partition #1
2= Partition #2
3= Partition #3
4= Partition #4
5= Partition #5
6= Partition #6
7= Partition #7
8= Partition #8
Segment 4 (Aux 4)
1= Partition #1
2= Partition #2
3= Partition #3
4= Partition #4
5= Partition #5
6= Partition #6
7= Partition #7
8= Partition #8
LOCATION 46 - AUXILIARY OUTPUT 1-4 SPECIAL TIMING (4 segments, feature selection data)
Location 46 contains special timing feature activation for the four auxiliary outputs. Segment 1 corresponds to
output 1; Segment 4 corresponds to output 4.
Segments 1 - 4:
24
1 = On if output should be timed in minutes; Off if timed in seconds.
2 = On if output should latch; Off if output should be timed.
3 = On if output should stop timing upon code entry; Off if the output should continue to time
upon code entry.
4 = On if output should only activate between the closing and opening time in loc. 52 and 53.
5 = On if output should only activate between the opening and closing time in loc. 52 and 53.
6 = On if output should be inverted (0 volts going to 12 volts when activated).
7 = Reserved.
8 = Reserved.
NX-8E CONTROL
LOCATION 47 - AUXILIARY OUTPUT #1, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Segment 2:
Use the chart on page 25 to select the event that will activate Auxiliary Output 1.
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 1, Location 46). Programming a "0" makes the output follow the event.
LOCATION 48 - AUXILIARY OUTPUT #2, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Segment 2:
Use the chart on page 25 to select the event that will activate Auxiliary Output 2.
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 2, Location 46). Programming a "0" makes the output follow the event.
LOCATION 49- AUXILIARY OUTPUT #3, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Segment 2:
Use the chart on page 25 to select the event that will activate Auxiliary Output 3.
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 3, Location 46). Programming a "0" makes the output follow the event.
LOCATION 50- AUXILIARY OUTPUT #4, EVENT AND TIME (2 segments, numerical data)
Segment 1:
Segment 2:
Use the chart on page 25 to select the event that will activate Auxiliary Output 4. .
Program the timing from 0-255 (minutes or seconds, depending on data programmed in
Segment 4, Location 46). Programming a "0" makes the output follow the event.
Table XI-1 AUXILIARY OUTPUT EVENT SELECTION
DATA
0
1
2
3
4
5
6
7
8
9
/
/
/
/
/
EVENT
DATA
EVENT
DATA
Burglary Alarm
Fire Alarm
24 Hour Alarm
Trouble Alarm
Tamper Alarm
Yelping Siren (Burglary)
Temporal Siren (Fire)
Any Siren
Any Bypass
18
19
20
21
22
23
24
25
26
Entry
Exit
Entry or Exit
Armed State
Disarmed State
Ready
Not Ready
Fire
Fire Trouble
36
37
38
39
40
41
42
43
44
AC Fail
27
Chime
45
/ Expander Trouble
Dynamic Battery Test Time
Open Period
Closed Period
10
11
12
13
Low Battery
/ Duress
/ Aux 1 Keypad Zone
/ Aux 2 Keypad Zone
28
29
30
31
46
47
48
49
14
/ Panic Keypad Zone
32
Listen-In
50
15
16
17
Keypad Tamper
/ Autotest
Alarm Memory
33
34
35
Line Seizure
Ground Start
Fail To Communicate
69
70
/
/
˜
/
˜
/
EVENT
Telephone Line Fault
Program Mode
Download In Process
Ground Fault
Short Circuit (Over-current)
Box Tamper
Siren Tamper
Any Open
Any Short
Any Fault (Open/ Short on
Non-Fire Zone)
Any Alarm
Beeping Keypad
Code Entry (See note below)
Key FOB Function 1
Key FOB Function 2
Forced Door Alarm
Forced Door Restore
˜ Events 49 & 50 require NX-408, NX-416, or NX-448 wireless receivers to operate.
/ If set to follow condition, these events will be 1 second.
Notes: When Event 48 is programmed, it is possible to program a user code's authorization to select which output(s)
a particular code will activate. When LED 8 is on for an authorization, then LEDs 1- 4 correspond to that code
activating outputs 1 - 4 respectively. (See programming the LED keypads on page 8.)
NX-8E CONTROL
25
L
LOCATION 51 - AUTOTEST CONTROL (4 segments, numerical data)
Segment 1:
Segment 2:
Segment 3:
Segment 4:
Program a "1" if the interval is to be in hours; Program a "0" if in days. Add a A2" to suppress
the daily test or a A3" to suppress the hourly test if any report has been sent.
Program the Autotest interval from 1-255 hours/days.
Program the Autotest report hour in 24-hour format (if the interval is in hours, this segment is
ignored).
Program the Autotest report time, number of minutes after the hour.
LOCATION 52 - OPENING TIME (2 segments, numerical data)
Location 52 contains the time in 24 hour format the NX-8E enables codes designated as arm only after closing.
This time is only valid on those days programmed in location 54. Note: Opening time must be earlier than
closing time for Auto Arm, Aux. Outputs, or Code Authorization to function properly.
Segment 1:
Segment 2:
Program the hour of the opening time.
Program the minutes after the hour of the opening time.
LOCATION 53 - CLOSING TIME/AUTOMATIC ARMING TIME (2 segments, numerical data)
Location 53 contains the time in 24 hour format the NX-8E disables the disarm capability for codes designated as
arm only after closing. This is also the time the Automatic Arming sequence will begin (if enabled in location 55)..
Segment 1:
Segment 2:
Program the hour of the closing / auto arm time.
Program the minutes after the hour of the closing / auto arm time.
LOCATION 54 - DAYS OF THE WEEK EACH PARTITION IS OPEN (8 Segments, feature selection data)
Location 54 selects which days of the week each partition is open. On these days, Aarm only after close window@
codes will be able to arm and disarm during open window. NOTE: If any partition is not programmed to be
opened and is programmed to Auto-Arm (Location 55), the NX-8E will try to arm every 45 minutes for the
duration of the closed period unless Auto Retry is disabled in location 55. On days not selected here, Aarm
only after close window@ codes will not disarm. Segment 1 is for partition 1, and segment 8 is for partition 8. (See
locations 52 and 53 for the opening and closing times for the open days.)
Segment 1-8: 1 - Open on Sunday.
2 - Open on Monday.
3 - Open on Tuesday.
4 - Open on Wednesday.
5 - Open on Thursday.
6 - Open on Friday.
7 - Open on Saturday.
8 – Reserved.
LOCATION 55 - DAYS OF THE WEEK FOR AUTO ARMING IN PARTITIONS 1 THRU 8 (8 Segments, feature
selection data)
Location 55 selects which days each partition will auto arm. Segment 1 is for partition 1, and segment 8 is for
partition 8. If a zone is faulted when the panel tries to auto arm, the zone will be bypassed.
Segments 1-8: 1 - Auto Arming on Sunday.
2 - Auto Arming on Monday.
3 - Auto Arming on Tuesday.
4 - Auto Arming on Wednesday.
5 - Auto Arming on Thursday.
6 - Auto Arming on Friday.
7 - Auto Arming on Saturday.
8 - Disable 45 minute retry timer.
26
NX-8E CONTROL
SLOW COMMUNICATOR FORMAT CODES
LOCATIONS 56- 83 ARE ONLY USED WHEN REPORTING EVENTS TO A PAGER OR USING A SLOW FORMAT
SUCH AS 4+2. WHEN USING CONTACT ID OR SIA, THERE IS NO NEED TO PROGRAM THESE LOCATIONS.
The digit programmed in each of the following locations will be sent as the upper HEX digit in place of the
alarm event code. The zone ID or user ID will always be reported as the lower HEX digit (1-F). For example, if
the zone ID or user ID is 15, the 4+2 lower digit will be “F” and if the zone ID or user ID is 16, the 4+2 digit will
be “1”. See Appendix 4 on page 72. NOTE: If Segments 2-8 are left as “0” (unprogrammed), they will follow
the Segment 1 selection. If Segment 1 is left as “0” and the feature is enabled in Location 23, the NX8E will
report “A”.
LOCATION 56 - RESTORE COMMUNICATOR CODE (8 segments, numerical data)
Location 56 contains the event code for any zone "Restore" for a 4+2 format. Refer to the box at the top of page 27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 57 - BYPASS COMMUNICATOR CODE
(8 segments, numerical data)
Location 57 contains the event code for a zone "Bypass" for a 4+2 format. Refer to the box at the top of page 27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 58 - TAMPER COMMUNICATOR CODE
(8 segments, numerical data)
Location 58 contains the event code for a zone "Tamper" for a 4+2 format. Refer to the box at the top of page 27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 59 - TROUBLE COMMUNICATOR CODE (8 segments, numerical data)
Location 59 contains the event code for a zone "Trouble" for a 4+2 format. Refer to the box at the top of page 27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 60 - SENSOR LOW BATTERY COMMUNICATOR CODE (8 segments, numerical data)
Location 60 contains the event code for a zone "Sensor Low Battery" for a 4+2 format. Refer to the box at the top of
page 27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 61- SENSOR MISSING COMMUNICATOR CODE (8 segments, numerical data)
Location 61 contains the event code for a zone "Sensor Missing" for a 4+2 format. Refer to the box at the top of page
27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 62 - DURESS COMMUNICATOR CODE (2 segments, numerical data)
Location 62 contains the digits that will be sent for a 4+2 format if the “Duress” code is enabled in location 44. Refer to
the box at the top of page 27.
LOCATION 63 - KEYPAD AUXILIARY 1 COMMUNICATOR CODE (2 segments, numerical data)
Location 63 contains the digits that will be sent for a 4+2 format if the keypad "Auxiliary 1" (Fire) is enabled in the
partition feature selection. Refer to the box at the top of page 27.
NX-8E CONTROL
27
SLOW COMMUNICATOR FORMAT CODES
LOCATION 64 - KEYPAD AUXILIARY 2 COMMUNICATOR CODE (2 segments, numerical data)
Location 64 contains the digits that will be sent for a 4+2 format if the keypad "Auxiliary 2" (Medical) is enabled in the
partition feature selection. Refer to the box at the top of page 27.
LOCATION 65 - KEYPAD PANIC COMMUNICATOR CODE (2 segments, numerical data)
Location 65 contains the digits that will be sent for a 4+2 format if the keypad "Panic" is enabled in the partition feature
selection. Refer to the box at the top of page 27.
LOCATION 66 - KEYPAD MULTIPLE CODE ENTRY TAMPER COMMUNICATOR CODE (2 segments, numerical
data)
Location 66 contains the digits that will be sent for a 4+2 format if the keypad "Multiple Code Entry" (Tamper) is
enabled in the partition feature selection. Refer to the box at the top of page 27.
LOCATION 67 - BOX TAMPER / BOX TAMPER RESTORE COMMUNICATOR CODE (4 segments, numerical
data)
Location 67 contains the digits that will be sent for a 4+2 format if the "Box Tamper" feature is enabled in location 37.
Segments 1 & 2 contain the digits of the "Box Tamper". Segments 3 & 4 contain the digits of the "Box Tamper
Restore". Refer to the box at the top of page 27.
LOCATION 68 - AC FAIL / AC FAIL RESTORE COMMUNICATOR CODES (4 segments, numerical data)
Location 68 contains the digits for a 4+2 format that will be sent if "AC Fail Reporting" is enabled. Segments 1 & 2
contain the digits of the "AC Fail". Segments 3 & 4 contain the digits of the "AC Fail Restore". Refer to the box at the
top of page 27.
LOCATION 69 - LOW BATTERY / LOW BATTERY RESTORE COMMUNICATOR CODES, SLOW SPEED
FORMATS ONLY (4 segments, numerical data)
Location 69 contains the digits for a 4+2 format that will be sent if "Low Battery Reporting" is enabled. Segments 1 & 2
contain the digits of the "Low Battery Reporting". Segments 3 & 4 contain the digits of the "Low Battery Restore".
Refer to the box at the top of page 27.
LOCATION 70 - AUX POWER OVERCURRENT/ AUX POWER OVERCURRENT RESTORE COMMUNICATOR
CODES (4 segments, numerical data)
Location 70 contains the digits for a 4+2 format that will be sent if "Aux Power Overcurrent Reporting" is enabled.
Segments 1 & 2 contain the digits of the "Aux Power Overcurrent Reporting". Segments 3 & 4 contain the digits of the
"Aux Power Overcurrent Restore". Refer to the box at the top of page 27.
LOCATION 71 - BELL TAMPER / BELL TAMPER RESTORE COMMUNICATOR CODES (4 segments, numerical
data)
Location 71 contains the digits for a 4+2 format that will be sent if siren supervision reporting is enabled. Segments 1
& 2 contain the digits of the "Bell Tamper Reporting". Segments 3 & 4 contain the digits of the "Bell Tamper Restore".
Refer to the box at the top of page 27.
LOCATION 72 - TELEPHONE LINE CUT / TELEPHONE LINE CUT RESTORE COMMUNICATOR CODES (4
segments, numerical data)
Location 72 contains the digits for a 4+2 format that will be sent if "Telephone Line Cut Reporting" is enabled.
Segments 1 & 2 contain the digits of the "Telephone Line Cut Reporting". Segments 3 & 4 contain the digits of the
"Telephone Line Cut Restore". Refer to the box at the top of page 27.
LOCATION 73 - GROUND FAULT / GROUND FAULT RESTORE COMMUNICATOR CODES (4 segments,
numerical data)
Location 73 contains the digits for a 4+2 format that will be sent if "Ground Fault Reporting" is enabled, and the NX870 is installed. Segments 1 & 2 contain the digits of the "Ground Fault Reporting". Segments 3 & 4 contain the digits
of the "Ground Fault Restore". Refer to the box on page 27.
28
NX-8E CONTROL
SLOW COMMUNICATOR FORMAT CODES
LOCATION 74 - EXPANDER TROUBLE / EXPANDER TROUBLE RESTORE COMMUNICATOR CODES (4
segments, numerical data)
Location 74 contains the digits for a 4+2 format that will be sent if "Expander Trouble Reporting" is enabled.
Segments 1 & 2 contain the digits of the "Expander Trouble Reporting". Segments 3 & 4 contain the digits of the
"Expander Trouble Restore". Refer to the box on page 27.
LOCATION 75 - FAIL TO COMMUNICATE COMMUNICATOR CODE (2 segments, numerical data)
Location 75 contains the digits for a 4+2 format that will be sent if the "Fail To Communicate Reporting" is enabled.
Refer to the box on page 27.
LOCATION 76 - LOG FULL COMMUNICATOR CODE (2 segments, numerical data)
Location 76 contains the digits for a 4+2 format if the "Log Full Reporting" is enabled. Refer to the box on page 27.
LOCATION 77 - OPENING COMMUNICATOR CODE (8 segments, numerical data)
Location 77 contains the digit of a 4+2 format if the "Opening Reporting" is enabled. Refer to the box on page 27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 78 - CLOSING COMMUNICATOR CODE (8 segments, numerical data)
Location 78 contains the digit of a 4+2 format if the "Closing Reporting" is enabled. Refer to the box on page 27.
Segment 1 = Partition 1
Segment 2 = Partition 2
Segment 3 = Partition 3
Segment 4 = Partition 4
Segment 5 = Partition 5
Segment 6 = Partition 6
Segment 7 = Partition 7
Segment 8 = Partition 8
LOCATION 79 - AUTOTEST COMMUNICATOR CODE (2 segments, numerical data)
Location 79 contains the digits for a 4+2 format that will be sent if the "Autotest" or "Manual Test" is enabled. Refer to
the box on page 27.
LOCATION 80 - RECENT CLOSING AND EXIT ERROR COMMUNICATOR CODE (2 segments, numerical data)
Location 80 contains the digits for a 4+2 format that will be sent if "Recent Closing" and/or "Exit Error Reporting" is
enabled. Segment 1 contains the digit for the "Recent Closing Reporting". Segment 2 contains the digit for the "Exit
Error Reporting". Refer to the box on page 27.
LOCATION 81 - START PROGRAM AND END PROGRAM COMMUNICATOR CODES (4 segments, numerical
data)
Location 81 contains the digits for a 4+2 format that will be sent if "Start / End Programming Reporting" is enabled.
Segment 1 contains the digit for the "Start Program Reporting". Segment 2 contains the digit for the "Start Program
Reporting". Segment 3 contains the digit for the "End Program Reporting". Segment 4 contains the digit for the "End
Program Reporting". Refer to the box on page 27.
LOCATION 82 - END DOWNLOAD COMMUNICATOR CODE (4 segments, numerical data)
Location 82 contains the digits for a 4+2 format that will be sent if "End Downloading Reporting" is enabled. Segment
1 and 2 are Reserved. Segment 3 contains the digit of the "End Download Reporting". Segment 4 contains the digit
of the "End Download Reporting". Note: A start download report will be sent to the internal event log. Refer to the box
on page 27.
LOCATION 83 - CANCEL COMMUNICATOR CODE (1 segments, numerical data)
Location 83 contains the digit for a 4+2 format that will be sent if "Cancel Reporting" is enabled. Segment 1 contains
the digit for the "Cancel Communicator Reporting". Refer to the box on page 27.
LOCATIONS 84-87 RESERVED.
NX-8E CONTROL
29
LOCATIONS 88-109 ARE FOR PROGRAMMING DIFFERENT ACCOUNT CODES AND/OR
FEATURES FOR EACH PARTITION. IF A LOCATION IS LEFT UNPROGRAMMED, THE
FEATURE FOR PARTITION 1 AND ACCOUNT CODE FOR THE PHONE NUMBER WILL BE USED.
LOCATION 88 - ACCOUNT CODE FOR PARTITION 1 (6 segments, numerical data)
Location 88 contains the account code sent when partition 1 is reported. If location 88 is left unprogrammed (all
A10"s), then the account code corresponding to the Phone number dialed will be used. If the account code is
less than six digits, program a A10" in the segment immediately after the last digit of the account code. If the account
code is 6 digits long, program all 6 segments.
LOCATION 89 - ACCOUNT CODE FOR PARTITION 2 (6 segments, numerical data)
Location 89 contains the account code sent when partition 2 is reported. If location 89 is left unprogrammed (all
A10"s), then the account code corresponding to the Phone number dialed will be used. If the account code is
less than six digits, program a A10" in the segment immediately after the last digit of the account code. If the account
code is 6 digits long program all 6 segments.
LOCATION 90 - PARTITION 2 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 90 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location
23 (page 18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1
will be used.
LOCATION 91 - PARTITION 2 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 91 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry time 1:
Segment 2, Exit time 1:
Segment 3, Entry time 2:
Segment 4, Exit time 2:
Segments 5 & 6:
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Reserved
LOCATION 92 - ACCOUNT CODE FOR PARTITION 3 (6 segments, numerical data)
The account code sent when partition 3 is reported is programmed in location 92. If location 92 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used. If
the account code is less than six digits, program a A10" in the segment immediately after the last digit of the account
code. If the account code is 6 digits long program all 6 segments.
LOCATION 93 - PARTITION 3 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 93 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be enabled
by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location 23 (page
18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1 will be
used.
LOCATION 94 - PARTITION 3 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 94 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry time 1:
Segment 2, Exit time 1:
Segment 3, Entry time 2:
Segment 4, Exit time 2:
Segments 5 & 6:
30
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Reserved
NX-8E CONTROL
LOCATION 95 - ACCOUNT CODE FOR PARTITION 4 (6 segments, numerical data)
The account code sent when partition 4 is reported is programmed in location 95. If location 95 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used. If the
account code is less than six digits, program a A10" in the segment immediately after the last digit of the account code.
If the account code is 6 digits long, program all 6 segments.
LOCATION 96 - PARTITION 4 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 96 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location
23 (page 18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1
will be used.
LOCATION 97 - PARTITION 4 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 97 is used to enter in seconds the Entry and exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry time 1:
Segment 2, Exit time 1:
Segment 3, Entry time 2:
Segment 4, Exit time 2:
Segments 5 & 6:
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Reserved
LOCATION 98 - ACCOUNT CODE FOR PARTITION 5 (6 segments, numerical data)
The account code sent when partition 5 is reported is programmed in location 98. If location 98 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used. If the
account code is less than six digits, program a A10" in the segment immediately after the last digit of the account code.
If the account code is 6 digits long, program all 6 segments.
LOCATION 99 - PARTITION 5 FEATURE AND REPORTING SELECTIONS (5 SEGMENTS, NUMERICAL DATA)
Location 99 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be enabled
by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location 23 (page
18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1 will be
used.
LOCATION 100 - PARTITION 5 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 100 is used to enter in seconds the Entry and exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1:
Segment 2, Exit Time 1:
Segment 3, Entry Time 2:
Segment 4, Exit Time 2:
Segments 5 & 6:
Entry time that will be used when a delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as delay 1.
Entry time that will be used when a delay 2zone type initiates an entry delay.
Exit time that will be used for all zones designated as delay 2.
Reserved
LOCATION 101 - ACCOUNT CODE FOR PARTITION 6 (6 segments, numerical data)
The account code sent when partition 6 is reported is programmed in location 101. If location 101 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used.
Program the account code is less than six digits, program a A10" in the segment immediately after the last digit of the
account code. If the account code is 6 digits long, program all 6 segments.
LOCATION 102 - PARTITION 6 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 102 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location
23 (page 18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1
will be used.
NX-8E CONTROL
31
LOCATION 103 - PARTITION 6 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 103 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1:
Segment 2, Exit Time 1:
Segment 3, Entry Time 2:
Segment 4, Exit Time 2:
Segments 5 & 6:
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Reserved
LOCATION 104 - ACCOUNT CODE FOR PARTITION 7 (6 segments, numerical data)
The account code sent when partition 7 is reported is programmed in location 104. If location 104 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used. If the
account code is less than six digits, program a A10" in the segment immediately after the last digit of the account code.
If the account code is 6 digits long, program all 6 segments.
LOCATION 105 - PARTITION 7 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 105 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location
23 (page 18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1
will be used.
LOCATION 106 - PARTITION 7 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 106 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1:
Segment 2, Exit Time 1:
Segment 3, Entry Time 2:
Segment 4, Exit Time 2:
Segments 5 & 6:
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 2.
Reserved
LOCATION 107 - ACCOUNT CODE FOR PARTITION 8 (6 segments, numerical data)
The account code sent when partition 8 is reported is programmed in location 107. If location 107 is left
unprogrammed (all A10") then the account code corresponding to the Phone number dialed will be used. If the
account code is less than six digits, program a A10" in the segment immediately after the last digit of the account code.
If the account code is 6 digits long, program all 6 segments.
LOCATION 108 - PARTITION 8 FEATURE AND REPORTING SELECTIONS (5 segments, feature selection data)
Location 108 is used to enable certain features that can be accessed or are visible to the user from the keypad of the
system. In addition, certain communicator reports are enabled in this location. Each of these features can be
enabled by partition. This location contains 5 segments, with eight possible features per segment. Refer to Location
23 (page 18) for the feature selections. If all segments are blank (nothing enabled), the features for partition 1
will be used.
LOCATION 109 - PARTITION 8 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 109 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid
entries are 10-255 seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1:
Segment 2, Exit Time 1:
Segment 3, Entry Time 2:
Segment 4, Exit Time 2:
Segments 5 & 6:
32
Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Exit time that will be used for all zones designated as Delay 1.
Entry time that will be used when a Delay 2 zone type initiates an entry Delay.
Exit time that will be used for all zones designated as Delay 2.
Reserved
NX-8E CONTROL
LOCATIONS 110-169 ARE USED TO CHANGE THE ZONE TYPES (Configurations) AS LISTED IN THE TABLE
ON PAGE 19. THESE LOCATIONS ARE CONSIDERED ADVANCED PROGRAMMING AND SHOULD
ONLY BE CHANGED WITH A THOROUGH UNDERSTANDING OF THE OPERATION OF EACH BIT.
LOCATION 110 - ZONE TYPE 1 ALARM EVENT CODE (1 segment, numerical data)
Location 110 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm.
4+2 Format Note: If 4+2 format is being used, the number programmed in this location will be sent as the upper hex
digit. The digit in location 110 should be from 1 to 15 when using 4+2 formats. The zone ID or user ID will be the
lower hex digit of the zone that is in alarm.
LOCATION 111 - ZONE TYPE 1 CHARACTERISTIC SELECT (5 segments, feature selection data)
Segment 1:
1 = Fire (turn on if this is a fire zone).
2 = 24 hour (turn on for non-fire 24 hour zones).
3 = Keyswitch zone. (normally open switch)
4 = Follower (turn on for burglary zones that are Instant during non-entry times).
5 = Delay 1 zone (follows timer 1 entry and exit times).
6 = Delay 2 zone (follows timer 2 entry and exit times).
7 = Interior (turn on if this zone should Automatically Bypass or Bypass for Stay Arming).
8 = Local only (turn on if this zone should not be reported).
Segment 2:
1 = On if Zone Type will beep the keypad for alarm.
2 = On if Zone Type will sound the yelping siren for alarm.
3 = On if Zone Type will sound the temporal siren for alarm.
4 = On if Zone Type will chime.
5 = On if Zone Type can be bypassed.
6 = On if Zone Type is included in the group shunt.
7 = On if Zone Type is force armable.
8 = On if Zone Type is entry guard.
Segment 3:
1 = On enables Fast Loop Response. (50mS)- Off= 500mS
2 = On enables Double End Of Line Tamper zone. (Mainly used for tamper on wireless zones)
3 = On enables Trouble Reporting zone. (Day zone and Fire zones)
4 = On if Zone Type is a Cross Zone.
5 = On enables Dialer Delay zone. (See location 40, page 23)
6 = On if Zone Type will swinger shutdown. (See location 38, page 23)
7 = On enables Restore reporting.
8 = On enables Listen-In. (See location 40, page 23)
Segment 4:
1 = On enables Zone Activity Monitor. (See location 40, page 23)
2 = On enables End of Line Resistor Defeat on Non-Fire/Non-Keyswitch zones.
3 = On delays alarm activation 60 seconds (Do not enable unless configured with Access Control.)
4 = On enables zone to act as request to exit input / disables for alarm activation.
5-8 = Reserved.
Segment 5:
Reserved.
LOCATION 112 - ZONE TYPE 2 ALARM EVENT CODE (1 segment, numerical data)
Location 112 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 113 - ZONE TYPE 2 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 114 - ZONE TYPE 3 ALARM EVENT CODE (1 segment, numerical data)
Location 114 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 115 - ZONE TYPE 3 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
NX-8E CONTROL
33
LOCATION 116 - ZONE TYPE 4 ALARM EVENT CODE (1 segment, numerical data)
Location 116 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 117 - ZONE TYPE 4 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 118 - ZONE TYPE 5 ALARM EVENT CODE (1 segment, numerical data)
Location 118 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 119 - ZONE TYPE 5 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 120 - ZONE TYPE 6 ALARM EVENT CODE (1 segment, numerical data)
Location 120 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 121 - ZONE TYPE 6 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 122 - ZONE TYPE 7 ALARM EVENT CODE (1 segment, numerical data)
Location 122 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 123 - ZONE TYPE 7 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 124 - ZONE TYPE 8 ALARM EVENT CODE (1 segment, numerical data)
Location 124 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 125 - ZONE TYPE 8 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 126 - ZONE TYPE 9 ALARM EVENT CODE (1 segment, numerical data)
Location 126 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 127 - ZONE TYPE 9 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 128 - ZONE TYPE 10 ALARM EVENT CODE (1 segment, numerical data)
Location 128 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 129 - ZONE TYPE 10 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 130 - ZONE TYPE 11 ALARM EVENT CODE (1 segment, numerical data)
Location 130 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 131 - ZONE TYPE 11 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
34
NX-8E CONTROL
LOCATION 132 - ZONE TYPE 12 ALARM EVENT CODE (1 segment, numerical data)
Location 132 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 133 - ZONE TYPE 12 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 134 - ZONE TYPE 13 ALARM EVENT CODE (1 segment, numerical data)
Location 134 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 135 - ZONE TYPE 13 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 136 - ZONE TYPE 14 ALARM EVENT CODE (1 segment, numerical data)
Location 136 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 137 - ZONE TYPE 14 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 138 - ZONE TYPE 15 ALARM EVENT CODE (1 segment, numerical data)
Location 138 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 139 - ZONE TYPE 15 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 140 - ZONE TYPE 16 ALARM EVENT CODE (1 segment, numerical data)
Location 140 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 141 - ZONE TYPE 16 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 142 - ZONE TYPE 17 ALARM EVENT CODE (1 segment, numerical data)
Location 142 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 143 - ZONE TYPE 17 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 144 - ZONE TYPE 18 ALARM EVENT CODE (1 segment, numerical data)
Location 144 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 145 - ZONE TYPE 18 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
NX-8E CONTROL
35
LOCATION 146 - ZONE TYPE 19 ALARM EVENT CODE (1 segment, numerical data)
Location 146 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 147 - ZONE TYPE 19 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 148 - ZONE TYPE 20 ALARM EVENT CODE (1 segment, numerical data)
Location 148 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 149 - ZONE TYPE 20 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 150 - ZONE TYPE 21 ALARM EVENT CODE (1 segment, numerical data)
Location 150 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 151 - ZONE TYPE 21 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 152 - ZONE TYPE 22 ALARM EVENT CODE (1 segment, numerical data)
Location 152 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 153 - ZONE TYPE 22 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 154 - ZONE TYPE 23 ALARM EVENT CODE (1 segment, numerical data)
Location 154 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 155 - ZONE TYPE 23 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 156 - ZONE TYPE 24 ALARM EVENT CODE (1 segment, numerical data)
Location 156 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 157 - ZONE TYPE 24 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 158 - ZONE TYPE 25 ALARM EVENT CODE (1 segment, numerical data)
Location 158 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 159 - ZONE TYPE 25 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
36
NX-8E CONTROL
LOCATION 160 - ZONE TYPE 26 ALARM EVENT CODE (1 segment, numerical data)
Location 160 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 161 - ZONE TYPE 26 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 162 - ZONE TYPE 27 ALARM EVENT CODE (1 segment, numerical data)
Location 162 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 163 - ZONE TYPE 27 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 164 - ZONE TYPE 28 ALARM EVENT CODE (1 segment, numerical data)
Location 164 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 165 - ZONE TYPE 28 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 166 - ZONE TYPE 29 ALARM EVENT CODE (1 segment, numerical data)
Location 166 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 167 - ZONE TYPE 29 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
LOCATION 168 - ZONE TYPE 30 ALARM EVENT CODE (1 segment, numerical data)
Location 168 contains the event code sent for a Contact ID or SIA report. The desired event code should be chosen
from the list on page 70. The zone ID will be that zone that is in alarm. If 4+2 format is being used, refer to Location
110 on page 33 for details.
LOCATION 169 - ZONE TYPE 30 CHARACTERISTIC SELECT (5 segments, feature selection data)
Use "Zone Type Characteristic Selections" described in Location 111, page 33.
L
LOCATION 170 - ZONES 49-56 ZONE TYPE (8 segments, numerical data)
Location 170 contains the Zone Type for zones 49 - 56. Segment 1 is for zone 49; Segment 8 is for zone 56. Default
Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 171 - PARTITION SELECT, ZONES 49-56 (8 segments of feature selection data)
Location 171 is used to select the partition(s) that zones 49-56 reside in. A zone may reside in any combination of the
8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 49 and Segment 8 corresponds to zone 56.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 172 - ZONES 57-64 ZONE TYPE (8 segments, numerical data)
Location 172 contains the Zone Type for zones 57-64. Segment 1 is for zone 57; Segment 8 is for zone 64. Default
Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
NX-8E CONTROL
37
LOCATION 173 - PARTITION SELECT, ZONES 57-64 (8 segments of feature selection data)
Location 173 is used to select the partition(s) that zones 57-64 reside in. A zone may reside in any combination of the
8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 57 and Segment 8 corresponds to zone 64.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 174 - ZONES 65-72 ZONE TYPE (8 segments, numerical data)
Location 174 contains the Zone Type for zones 65 - 72. Segment 1 is for zone 65; Segment 8 is for zone 72. Default
Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 175 - PARTITION SELECT, ZONES 65-72 (8 segments of feature selection data)
Location 175 is used to select the partition(s) that zones 65-72 reside in. A zone may reside in any combination of the
8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 65 and Segment 8 corresponds to zone 72.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 176 - ZONES 73-80 ZONE TYPE (8 segments, numerical data)
Location 176 contains the Zone Type for zones 73-80. Segment 1 is for zone 73; Segment 8 is for zone 80. Default
Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 177 - PARTITION SELECT, ZONES 73-80 (8 segments of feature selection data)
Location 177 is used to select the partition(s) that zones 73-80 reside in. A zone may reside in any combination of the
8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 73 and Segment 8 corresponds to zone 80.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 178 - ZONES 81-88 ZONE TYPE (8 segments, numerical data)
Location 178 contains the Zone Type for zones 81-88. Segment 1 is for zone 81; Segment 8 is for zone 88. Default
Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 179 - PARTITION SELECT, ZONES 81-88 (8 segments of feature selection data)
Location 173 is used to select the partition(s) that zones 81 - 88 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 81 and Segment 8 corresponds to zone 88.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 180 - ZONES 89-96 ZONE TYPE (8 segments, numerical data)
Location 180 contains the Zone Type for zones 89 - 96. Segment 1 is for zone 89; Segment 8 is for zone 96. Default
Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
38
NX-8E CONTROL
LOCATION 181 - PARTITION SELECT, ZONES 89-96 (8 segments of feature selection data)
Location 181 is used to select the partition(s) that zones 89 - 96 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 89 and Segment 8 corresponds to zone 96.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 182 - ZONES 97-104 ZONE TYPE (8 segments, numerical data)
Location 182 contains the Zone Type for zones 97-104. Segment 1 is for zone 97; Segment 8 is for zone 104.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 183 - PARTITION SELECT, ZONES 97-104 (8 segments of feature selection data)
Location 183 is used to select the partition(s) that zones 97-104 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 97 and Segment 8 corresponds to zone 104.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 184 - ZONES 105-112 ZONE TYPE (8 segments, numerical data)
Location 184 contains the Zone Type for zones 105-112. Segment 1 is for zone 105; Segment 8 is for zone 112.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 185 - PARTITION SELECT, ZONES 105-112 (8 segments of feature selection data)
Location 185 is used to select the partition(s) that zones 105-112 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 105 and Segment 8 corresponds to zone 112.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 186 - ZONES 113-120 ZONE TYPE (8 segments, numerical data)
Location 186 contains the Zone Type for zones 113-120. Segment 1 is for zone 113; Segment 8 is for zone 120.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 187 - PARTITION SELECT, ZONES 113-120 (8 segments of feature selection data)
Location 187 is used to select the partition(s) that zones 113-120 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 113 and Segment 8 corresponds to zone 120.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 188 - ZONES 121-128 ZONE TYPE (8 segments, numerical data)
Location 188 contains the Zone Type for zones 121-128. Segment 1 is for zone 121; Segment 8 is for zone 128.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 189 - PARTITION SELECT, ZONES 121-128 (8 segments of feature selection data)
Location 189 is used to select the partition(s) that zones 121-128 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 121 and Segment 8 corresponds to zone 128.
NX-8E CONTROL
39
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 190 - ZONES 129-136 ZONE TYPE (8 segments, numerical data)
Location 190 contains the Zone Type for zones 129-136. Segment 1 is for zone 129; Segment 8 is for zone 136.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 191 - PARTITION SELECT, ZONES 129-136 (8 segments of feature selection data)
Location 191 is used to select the partition(s) that zones 129-136 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 129 and Segment 8 corresponds to zone 136.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 192 - ZONES 137-144 ZONE TYPE (8 segments, numerical data)
Location 192 contains the Zone Type for zones 137-144. Segment 1 is for zone 137; Segment 8 is for zone 144.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 193 - PARTITION SELECT, ZONES 137-144 (8 segments of feature selection data)
Location 193 is used to select the partition(s) that zones 137-144 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 137 and Segment 8 corresponds to zone 144.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 194 - ZONES 145-152 ZONE TYPE (8 segments, numerical data)
Location 194 contains the Zone Type for zones 145-152. Segment 1 is for zone 145; Segment 8 is for zone 152.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 195 - PARTITION SELECT, ZONES 145-152 (8 segments of feature selection data)
Location 195 is used to select the partition(s) that zones 145-152 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 145 and Segment 8 corresponds to zone 152.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 196 - ZONES 153-160 ZONE TYPE (8 segments, numerical data)
Location 196 contains the Zone Type for zones 153-160. Segment 1 is for zone 153; Segment 8 is for zone 160.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 197 - PARTITION SELECT, ZONES 153-160 (8 segments of feature selection data)
Location 197 is used to select the partition(s) that zones 153-160 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 153 and Segment 8 corresponds to zone 160.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
40
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
NX-8E CONTROL
L
LOCATION 198 - ZONES 161-168 ZONE TYPE (8 segments, numerical data)
Location 198 contains the Zone Type for zones 161-168. Segment 1 is for zone 161; Segment 8 is for zone 168.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 199 - PARTITION SELECT, ZONES 161-168 (8 segments of feature selection data)
Location 199 is used to select the partition(s) that zones 161-168 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 161 and Segment 8 corresponds to zone 168.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 200 - ZONES 169-176 ZONE TYPE (8 segments, numerical data)
Location 200 contains the Zone Type for zones 169-176. Segment 1 is for zone 169; Segment 8 is for zone 176.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 201 - PARTITION SELECT, ZONES 169-176 (8 segments of feature selection data)
Location 201 is used to select the partition(s) that zones 169-176 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 169 and Segment 8 corresponds to zone 176.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 202 - ZONES 177-184 ZONE TYPE (8 segments, numerical data)
Location 202 contains the Zone Type for zones 177-184. Segment 1 is for zone 177; Segment 8 is for zone 184.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 203 - PARTITION SELECT, ZONES 177-184 (8 segments of feature selection data)
Location 203 is used to select the partition(s) that zones 177-184 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 177 and Segment 8 corresponds to zone 184.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
L
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 204 - ZONES 185-192 ZONE TYPE (8 segments, numerical data)
Location 204 contains the Zone Type for zones 185-192. Segment 1 is for zone 185; Segment 8 is for zone 192.
Default Zone Types are found in the table on page 19. To customize a Zone Type, see page 33.
LOCATION 205 - PARTITION SELECT, ZONES 185-192 (8 segments of feature selection data)
Location 205 is used to select the partition(s) that zones 185-192 reside in. A zone may reside in any combination of
the 8 partitions. If a burglary zone resides in more than 1 partition, it will only be active when all partitions are
armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1
corresponds to zone 185 and Segment 8 corresponds to zone 192.
Segments 1 - 8:
1 = Partition #1
2 = Partition #2
NX-8E CONTROL
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
41
LOCATION 206 – AUTO DISARM DAY SELECTOR (8 segments of feature selection data)
Location 206 selects which days each partition will auto disarm. Segment 1 is for partition 1, and segment 8 is for
partition 8. If a zone is faulted when the panel tries to auto disarm, the zone will be bypassed.
Segments 1-8: 1 - Auto Disarming on Sunday.
2 - Auto Disarming on Monday.
3 - Auto Disarming on Tuesday.
4 - Auto Disarming on Wednesday.
5 - Auto Disarming on Thursday.
6 - Auto Disarming on Friday.
7 - Auto Disarming on Saturday.
8 - Reserved.
LOCATION 207 – SERIAL PORT SELECTOR (1 segment of feature selection data)
Location 206 enables the serial port operations. There is one segment
“0” = Disabled (Default)
“1” = NX584 enabled
“2” = Serial Printer Enabled.
LOCATION 208 – BAUD RATE TABLE (1 segment of numerical data)
The NX584 can operate on a number of different baud rates. Consult the home automation application information to
determine the best baud rate for your application and program it in Location 208. The default is “2” – 9600 Baud or
the serial printer baud rate.
0 = 2400 Baud (2.4K)
1 = 4800 Baud (4.8K)
2 = 9600 Baud (9.6K)
3 = 19200 Baud (19.2K)
4 = 38400 Baud (38.4K)
5-7 = Reserved
LOCATION 209 – PROGRAMMING THE NX-8E HOME AUTOMATION PROTOCOL (1 segment of numerical data)
The NX-8E home automation protocol can operate in one of two possible modes - binary or ASCII. Consult the home
automation application information to determine the proper mode for your application and program it in Location 209.
The default is “Off” – Binary.
Option 1
LED 0ff = Binary
LED On = ASCII
Options 2 - 8
Reserved
LOCATION 210 – ENABLING THE NX-8E TRANSITION-BASED BROADCASTS (2 segments of feature
selection data)
The NX-8E can be programmed to automatically send information to the home automation system whenever there has
been a change in this information. This is referred to as ‘transition-based broadcasting’. Which information packets
use ‘transition-based broadcasting’ is dependent upon the application and the capabilities of the home automation
system. Location 210 is used to enable and disable the appropriate transition based broadcasts. Consult the home
automation application information and enable the appropriate transition based broadcasts in Location 210.
Segment 1:
DATA
1
2
3-4
5
6
7
8
ENABLES TRANSITION
Reserved
Interface Configuration at power-up / end of download / program mode
Reserved
Zone Status Message
Zones Snapshot Message
Partition Status Message
Partitions Snapshot Message
Segment 2:
DATA
1
2
3
4
5-8
42
ENABLES TRANSITION
System Status Message
X-10 Message Received
Log Event Message
Keypad Message Received
Reserved
NX-8E CONTROL
LOCATION 211 - PROGRAMMING THE COMMAND/REQUEST ENABLES (4 segments of feature selection
data)
The NX-8E has the ability to perform a variety of commands asked of it by the home automation system. For example,
it is possible to allow arming and disarming of the security system, programming of the security system, or bypassing
of zones by the home automation system. Location 211 is used to select which commands, if any you wish the home
automation system to have access. Consult the home automation application information and enable the appropriate
commands for your application. CAUTION: IT IS IMPORTANT TO UNDERSTAND THE CAPABILITES OF THE
HOME AUTOMATION SYSTEM TO AVOID COMPROMISING THE SECURITY OF YOUR SYSTEM WHEN
PROGRAMMING THIS LOCATION.
Segment 1:
DATA
1
2
3
4
5
6
7
8
SUPPORTED REQUEST / COMMAND
Reserved
Interface Configuration Request
Reserved
Zone Name Request
Zone Status Request
Zones Snapshot Request
Partition Status Request
Partitions Snapshot Request
Segment 2:
DATA
1
2
3
4
5
6-8
SUPPORTED REQUEST / COMMAND
System Status Request
Send X-10 Message
Log Event Request
Send Keypad Text Message
Keypad Terminal Mode Request
Reserved
Segment 3:
DATA
1
2
3
4
5
6
7
8
SUPPORTED REQUEST / COMMAND
Program Data Request
Program Data Command
User Information Request with PIN
User Information Request without PIN
Set User Code Command with PIN
Set User Code Command without PIN
Set User Authorization Command with PIN
Set User Authorization Command without PIN
Segment 4:
DATA
1
2
3
4
5
6
7
8
NX-8E CONTROL
SUPPORTED REQUEST / COMMAND
Reserved
Reserved
Store Communication Event Command
Set Clock / Calendar Command
Primary Keypad Function with PIN
Primary Keypad Function without PIN
Secondary Keypad Function
Zone Bypass Toggle
43
LOCATION 212 - PROGRAMMING THE LCD KEYPAD ADDRESS
(1 segment of numerical data)
Certain commands in the NX-8E require it to know the location of at least 1 LCD keypad (if one exists in the system). If
your system has an LCD keypad it is recommended that it be placed in partition 1 keypad 1. This will allow location
212 to be left at the factory default. If the LCD keypad is selected as something other than partition 1/ keypad 1
program the appropriate address in location 212. Select the address from the following chart.
44
KEYPAD
PART 1
PART 2
PART 3
PART 4
PART 5
PART 6
PART 7
PART 8
1
192
193
194
195
196
197
198
199
2
200
201
202
203
204
205
206
207
3
208
209
210
211
212
213
214
215
4
216
217
218
219
220
221
222
223
5
224
225
226
227
228
229
230
231
6
232
233
234
235
236
237
238
239
7
240
241
242
243
244
245
246
247
8
248
249
250
251
252
253
254
255
NX-8E CONTROL
XII.
PROGRAMMING WORKSHEETS
(Factory defaults for segments are in bold italics text and "Quick Start" locations are identified with the L symbol.)
LOC
PG
DESCRIPTION
L
0
13
PHONE #1
L
L
L
1
13
PHONE #1, ACCOUNT CODE
2
13
PHONE #1, REPORTING FORMAT
3
13
4
DEFAULT
PROGRAMMING DATA
14-14-14-14-14-14-14-14-1414-14-14-14-14-14-14-14-1414-14
10 - 10 - 10 - 10 - 10 - 10
__ __ __ __ __ __ __ __ __ __
__ __ __ __ __ __ __ __ __ __
0
_
______
PHONE #1, DIAL ATTEMPTS
8
_
BACKUP CONTROL
0
_
14 PHONE #1, SELECTING EVENTS TO REPORT TO PHONE #1
Segment #1 (Circle Numbers To Program)
Segment #2 (Circle Numbers To Program)
L
6
L
L
7
1 = Alarms and Restores
1 = Tampers
2 = Open/Close
2 = Short Circuit & Ground Fault
3 = Bypass
3 = Sensor Lost
4 = Zone Trouble
4 = Sensor Low Battery
5 = Power Trouble (AC Failure or Low Battery) 5 = Expander Trouble
6 = Siren & Telephone Fault
6 = Failure To Communicate
7 = Test Reports
7 = Zone Activity Monitor
8 = Program, Download, & Log Full
8 = Reserved
14 PHONE #1, SELECTING WHICH PARTITIONS REPORT TO PHONE #1
Segment #1 (Circle Numbers To Program)
1 = Partition #1
3 = Partition #3
5 = Partition #5
7 = Partition #7
2 = Partition #2
4 = Partition #4
6 = Partition #6
8 = Partition #8
14 PHONE #2
14-14-14-14-14-14-14-14-14-14- __ __ __ __ __ __ __ __ __ __
14-14-14-14-14-14-14-14-14-14 __ __ __ __ __ __ __ __ __ __
14 PHONE #2, ACCOUNT CODE
10 - 10 - 10 - 10 - 10 - 10
______
8
15
9
15
5
10
11
12
13
PHONE #2, REPORTING FORMAT
0
_
PHONE #2, DIAL ATTEMPTS
8
_
BACKUP CONTROL
0
_
15 PHONE #2, SELECTING EVENTS TO REPORT TO PHONE #2
Segment #1 (Circle Numbers To Program)
Segment #2 (Circle Numbers To Program)
1 = Alarms and Restores
1 = Tampers
2 = Open/Close
2 = Short Circuit & Ground Fault
3 = Bypass
3 = Sensor Lost
4 = Zone Trouble
4 = Sensor Low Battery
5 = Power Trouble (AC Failure or Low Battery)
5 = Expander Trouble
6 = Siren & Telephone Fault
6 = Failure To Communicate
7 = Test Reports
7 = Zone Activity Monitor
8 = Program, Download, & Log Full
8 = Reserved
16 PHONE #2, SELECTING WHICH PARTITIONS REPORT TO PHONE #2
Segment #1 (Circle Numbers To Program)
1 = Partition #1
3 = Partition #3
5 = Partition #5
7 = Partition #7
2 = Partition #2
4 = Partition #4
6 = Partition #6
8 = Partition #8
16 PHONE #3
14-14-14-14-14-14-14-14-14-14- __ __ __ __ __ __ __ __ __ __
14-14-14-14-14-14-14-14-14-14 __ __ __ __ __ __ __ __ __ __
16
NX-8E CONTROL
PHONE #3, ACCOUNT CODE
10 - 10 - 10 - 10 - 10 - 10
______
45
LOC
14
15
19
PG
DESCRIPTION
DEFAULT
PROGRAMMING DATA
16 PHONE #3, REPORTING FORMAT
0
_
16 PHONE #3, DIAL ATTEMPTS
8
_
BACKUP CONTROL
0
_
17 PHONE #3, SELECTING EVENTS TO REPORT TO PHONE #3
Segment #1 (Circle Numbers To Program)
Segment #2 (Circle Numbers To Program)
1 = Alarms and Restores
1 = Tampers
2 = Open/Close
2 = Short Circuit & Ground Fault
3 = Bypass
3 = Sensor Lost
4 = Zone Trouble
4 = Sensor Low Battery
5 = Power Trouble (AC Failure or Low Battery) 5 = Expander Trouble
6 = Siren & Telephone Fault
6 = Failure To Communicate
7 = Test Reports
7 = Zone Activity Monitor
8 = Program, Download, & Log Full
8 = Reserved
17 PHONE #3, SELECTING WHICH PARTITIONS REPORT TO PHONE #3
Segment #1 (Circle Numbers To Program)
1 = Partition #1
3 = Partition #3
5 = Partition #5
7 = Partition #7
2 = Partition #2
4 = Partition #4
6 = Partition #6
8 = Partition #8
17 FORMAT OVERRIDE
Segment #1 (Circle Numbers To Program)
Segment #2 (Circle Numbers To Program)
1 = ON - 1800hz transmit; OFF - 1900hz
1 = ON - pager format (no handshake required)
2 = ON - 1400/2300 handshake
2 = ON - 2300hz handshake; OFF - 1400hz.
3 = ON - cksum parity; OFF - double round 3 = Reserved
parity
4 = Reserved
4 = ON - 2 digit event code; OFF - 1 digit code 5 = ON - Contact ID
5 = Reserved.
6 = ON - SIA
6 = Reserved.
7 = ON - Contact ID or 4+3
7 = ON - 20 p.p.s.; OFF - 10 or 40 p.p.s.
8 = ON - DTMF
8 = ON - 10 p.p.s.; OFF - 20 or 40 p.p.s.
Segments #3 & #4 RESERVED
17 DOWNLOAD ACCESS CODE
8-4-8-0-0-0-0-0
________
20
17
RINGS TO ANSWER DOWNLOAD
21
18
DOWNLOAD CONTROL
16
17
18
L
L
L
L
46
22
18
8
Segment #1 (Circle Numbers To Program)
1 = Enables two call answering machine defeat
2 = Enables tone sniff answering machine defeat
3 = Requires callback before downloading
4 = Shutdown control panel
5 = Lock out local programming
6 = Lock out communicator programming
7 = Lock out download section
8 = Enables callback at autotest interval
CALLBACK PHONE NUMBER
14-14-14-14-14-14-14-14-1414-14-14-14-14-14-14-14-1414-14
_
__ __ __ __ __ __ __ __ __ __
__ __ __ __ __ __ __ __ __ __
NX-8E CONTROL
LOC
23
L
L
24
PG
18
DESCRIPTION
PARTITION #1, FEATURE SELECTION
DEFAULT
19
Segment #1
1 = Quick Arm
2 = Re-Exit
3 = Auto Bypass
4 = Silent Panic
Segment #2
1 = LED extinguish enable
2 = Require user code for bypassing zones
3 = Bypass sounder alert
4 = AC power/low battery sounder alert
Segment #3
1 = Open/Close
2 = Bypass
3 = Restore
4 = Trouble
Segment #4
1 = Late to Close / Early to Open
2 = Auto Arm in Stay Mode
3 = Reserved
4 = Disables door delay in Night Mode
Segment #5 RESERVED
ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segments #5 & #6
L
L
25
26
27
28
20
20
21
21
NX-8E CONTROL
PROGRAMMING DATA
5 = Audible Panic
6 = Auxiliary 1
7 = Auxiliary 2
8 = Multi Keypress Tamper
5 = Enables bypass toggle
6 = Enables silent auto arm
7 = Enables automatic instant
8 = Enables Instant Mode toggle
5=
6=
7=
8=
Tamper
Cancel
Recent Closing
Exit Error
5 = Reserved
6 = Reserved
7 = Reserved
8 = Reserved
30
60
30
60
Reserved
ZONES 1-8, ZONE TYPES
3-5-6-6-6-6-6-6
________
ZONES 1-8, PARTITION SELECTION (Segment 1=Zone 1 thru Segment 8=Zone 8)
Segments
1
2
3
4
5
6
7
8
Partition #1
Partition #2
Partition #3
Partition #4
Partition #5
Partition #6
Partition #7
Partition #8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
ZONES 9-16, ZONE TYPES
6-6-6-6-6-6-6-6
________
ZONES 9-16, PARTITION SELECTION (Segment 1=Zone 9 thru Segment 8=Zone 16)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
8
1
2
3
4
5
6
7
8
47
LOC
L
L
L
L
48
PG
DESCRIPTION
DEFAULT
PROGRAMMING DATA
6-6-6-6-6-6-6-6
________
29
21
ZONES 17-24, ZONE TYPES
30
21
ZONES 17-24, PARTITION SELECTION (Segment 1=Zone 17 thru Segment 8=Zone 24)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
31
21
ZONES 25-32, ZONE TYPES
32
21
ZONES 25-32, PARTITION SELECTION
Segments
1
2
1
1
Partition #1
2
2
Partition #2
3
3
Partition #3
4
4
Partition #4
5
5
Partition #5
6
6
Partition #6
7
7
Partition #7
8
8
Partition #8
6-6-6-6-6-6-6-6
8
1
2
3
4
5
6
7
8
________
(Segment 1=Zone 25 thru Segment 8=Zone 32)
3
4
5
6
7
1
1
1
1
1
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
7
7
7
7
7
8
8
8
8
8
6-6-6-6-6-6-6-6
8
1
2
3
4
5
6
7
8
33
21
ZONES 33-40, ZONE TYPES
34
21
ZONES 33-40, PARTITION SELECTION (Segment 1=Zone 33 thru Segment 8=Zone 40)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
6-6-6-6-6-6-6-6
________
35
22
ZONES 41-48, ZONE TYPES
36
22
ZONES 41-48, PARTITION SELECTION (Segment 1=Zone 41 thru Segment 8=Zone 48)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
8
1
2
3
4
5
6
7
8
________
8
1
2
3
4
5
6
7
8
NX-8E CONTROL
LOC
L
37
PG
22
NX-8E CONTROL
DESCRIPTION
DEFAULT
PROGRAMMING DATA
SIREN AND SYSTEM SUPERVISION
Segment #1 (Circle numbers to program)
Siren sounds for telephone line cut while armed.
1
Siren sounds for telephone line cut while disarmed.
2
Siren blast at arming.
3
Siren blast at exit delay expiration.
4
Siren blast at closing kissoff.
5
Siren sounds during a cross-zone verification time.
6
Siren sounds for a tamper.
7
Siren blast one time for keyswitch arming, two times for disarming.
8
Segment #2 (Circle numbers to program)
Convert siren driver to voltage out.
1
Siren sounds for expander trouble (required for U.L.).
2
Immediate Restore by zone.
3
Dynamic battery test performed upon arming.
4
Battery missing test performed every 12 seconds.
5
Manual bell test performed during [r]-[4]-[4] test function.
6
Manual communicator test performed during [r]-[4]-[4] test function.
7
Box tamper enabled.
8
Segment #3 (Circle numbers to program)
Box Tamper report enabled.
1
AC Fail report enabled.
2
Low Battery report enabled.
3
Auxiliary power over current report enabled.
4
Siren supervision report enabled.
5
Telephone Line Cut report enabled.
6
Ground Fault Detection report enabled.
7
Expander trouble report enabled.
8
Segment #4 (Circle numbers to program)
Failure To Communicate report enabled.
1
Log Full report enabled.
2
Autotest report enabled.
3
Start and End Programming report enabled.
4
End Download report enabled.
5
Sensor Low Battery report enabled.
6
Sensor Missing report enabled.
7
Reserved.
8
Segment #5 (Circle numbers to program)
Lost Clock service LED enable.
1
Zone Doubling enable.
2
Disable on-board eight zones.
3
Enables two trips on the same cross-zone to activate the alarm.
4
Disables bypass reports for force armed zones
5
Silent exit.
6
Clock uses internal crystal.
7
Disable Temporal Siren on Fire (Do not disable on UL listed systems)
8
Segment #6
Enable 2-wire Smoke Detector.
1
Reserved.
2
Enable Zone Activity in Hours (not Days)
3
Enable Daylight Savings Time (DST)
4
Reserved
5
Disable Clean Me report.
6
Reserved.
7-8
Segment #7 - RESERVED
49
LOC
PG
DESCRIPTION
DEFAULT
L
L
38
23
SWINGER SHUTDOWN COUNT
39
23
KEYPAD SOUNDER CONTROL
Segment #1 (Circle numbers to program)
1
Keypad sounds for Telephone Line Cut when in the Armed state.
2
Keypad sounds for Telephone Line Cut when in the Disarmed state.
3
Keypad sounds upon AC Power Failure.
4
Keypad sounds upon Low Battery Detection.
5
Keypad sounds during Cross Zone Trip Time.
6
Keypad sounds for Tamper Alarm.
7
Reserved.
8
Keypad sounds for expander trouble (required for UL).
L
40
23
SYSTEM TIMERS
Segment #1 Dynamic Battery Test duration (0-255 minutes)
Segment #2 AC Failure report delay (0-255 minutes)
Segment #3 Power Up Delay (0-60 seconds)
Segment #4 Siren Time (1-255 minutes)
Segment #5 Telephone Line Cut delay (0-255 seconds)
Segment #6 Cross Zone Time (0-255 minutes)
Segment #7 Chime Time in 50 mS increments (0-255)
Segment #8 Dialer delay ( 0-255 seconds)
Segment #9 Fire Alarm Verification Time (120-255 sec.)
Segment #10 Listen-In Time (0-255 seconds)
Segment #11 Zone Monitor Timer (0-255 Days)
Segment #12 – 14 Reserved
L
50
DATA
0
_
0
5
0
8
0
5
3
0
0
0
_
_
_
_
_
_
_
_
_
_
41
23
SPECIAL FEATURES
Segment #1 (Circle numbers to program)
Enables 6-digit code option. All arm/disarm/Go To Program codes require six digits
1
Requires valid user code entry for [r]-[9]-[8] and [r]-[9]-[9] functions to work.
2
Enable Auto Cancel / Abort.
3
Enable Walk-Test Mode.
4
Reserved.
5
Reserved.
6
Reserved.
7
Reserved.
8
42
24
GO TO PROGRAM CODE
43
24
GO TO PROGRAM CODE PARTITION AND AUTHORIZATION
Segment #1 (Circle numbers to program)
Reserved.
1
Enables "Go To Program Code" as an arm only code.
2
Enables "Go To Program Code" as an arm only after closing.
3
Enables "Go To Program Code" as a master arm/disarm code (can change user codes)
4
Enables "Go To Program Code" as an arm/disarm code.
5
Enables "Go To Program Code" to bypass zones.
6
Enables "Go To Program Code" opening and closing reports.
7
Reserved.
8
9-7-1-3-0-0
______
NX-8E CONTROL
LOC
L
DESCRIPTION
43
24
Segment #2 (Circle numbers to program)
Enables "Go To Program Code" for partition #1.
1
Enables "Go To Program Code" for partition #2.
2
Enables "Go To Program Code" for partition #3.
3
Enables "Go To Program Code" for partition #4.
4
Enables "Go To Program Code" for partition #5.
5
Enables "Go To Program Code" for partition #6.
6
Enables "Go To Program Code" for partition #7.
7
Enables "Go To Program Code" for partition #8.
8
44
24
DURESS CODE
45
24
46
L
PG
DEFAULT
DATA
15-15-15-15-15-15
______
AUXILIARY OUTPUTS 1-4 PARTITION SELECTION
Segments
1
2
3
4
1
1
1
1
Partition #1
2
2
2
2
Partition #2
3
3
3
3
Partition #3
4
4
4
4
Partition #4
5
5
5
5
Partition #5
6
6
6
6
Partition #6
7
7
7
7
Partition #7
8
8
8
8
Partition #8
24 AUXILIARY OUTPUTS 1-4 SPECIAL TIMING
Segments
Auxiliary output timed in minutes.
Auxiliary output to latch.
Auxiliary output to stop timing upon user code entry.
Auxiliary output to activate only between closing and opening time.
Auxiliary output to activate only between opening and closing time.
Invert auxiliary output (0 volts going to 12 volts when activated).
Reserved
Reserved
47
25
48
25
49
25
50
25
51
26 AUTOTEST CONTROL
Segment #1: Program a "1" if the interval is hours, a "0" if in
days. Add a A2" to suppress the daily test or a A3" to suppress
the hourly test.
Segment #2: Program the autotest interval from 1-255 days or
hours.
Segment #3: Program the autotest report in 24-hour time
format.
Segment #4: Program the autotest report time, minutes after
the hour.
NX-8E CONTROL
1
1
2
3
4
5
6
7
8
2
1
2
3
4
5
6
7
8
3
1
2
3
4
5
6
7
8
4
1
2
3
4
5
6
7
8
AUXILIARY OUTPUT #1, EVENT & TIME
Segment #1: Program the event number for output #1 here. 0=Burglary alarm
Segment #2: Program the timing for output #1 here.
10 seconds
AUXILIARY OUTPUT #2, EVENT & TIME
Segment #1: Program the event number for output #2 here.
1=Fire alarm
Segment #2: Program the timing for output #2 here.
10 seconds
AUXILIARY OUTPUT #3, EVENT & TIME
Segment #1: Program the event number for output #3 here. 2= 24 Hour Alarm
Segment #2: Program the timing for output #3 here.
10 seconds
AUXILIARY OUTPUT #4, EVENT & TIME
Segment #1: Program the event number for output #4 here.
21-Armed State
Segment #2: Program the timing for output #4 here.
0=Follow condition
1
24
2
0
51
LOC
52
53
54
55
PG
DESCRIPTION
DEFAULT
26 OPENING TIME
Segment #1: Program the hour of the opening time.
Segment #2: Program the minutes after the hour of the
opening time.
26 CLOSING TIME / AUTO ARMING TIME
Segment #1: Program the hour of the closing time / auto
arming time.
Segment #2: Program the minutes after hour of closing / auto
arming time.
26
26
DAYS OF THE WEEK EACH PARTITION IS OPEN
Segments
1
2
3
4
1
1
1
1
Sunday
2
2
2
2
Monday
3
3
3
3
Tuesday
4
4
4
4
Wednesday
5
5
5
5
Thursday
6
6
6
6
Friday
7
7
7
7
Saturday
8
8
8
8
Reserved
DATA
8
0
20
0
5
1
2
3
4
5
6
7
8
6
1
2
3
4
5
6
7
8
DAYS OF THE WEEK "AUTO ARMING" WILL OCCUR IN PARTITIONS 1-8
Segments
1
2
3
4
5
6
1
1
1
1
1
1
Sunday
2
2
2
2
2
2
Monday
3
3
3
3
3
3
Tuesday
4
4
4
4
4
4
Wednesday
5
5
5
5
5
5
Thursday
6
6
6
6
6
6
Friday
7
7
7
7
7
7
Saturday
8
8
8
8
8
8
Disable Retry
7
1
2
3
4
5
6
7
8
8
1
2
3
4
5
6
7
8
7
1
2
3
4
5
6
7
8
8
1
2
3
4
5
6
7
8
COMMUNICATOR CODES FOR SLOW SPEED FORMATS ONLY
The digit programmed in each of the following locations will be sent as the upper HEX digit in place of the alarm
event code. The zone ID or user ID will always be reported as the lower HEX digit (1-F). For example, if the zone ID
or user ID is 15, the 4+2 lower digit will be “F” and if the zone ID or user ID is 16, the 4+2 lower digit will be “1”.
NOTE: If Segments 2-8 are left as “0” (unprogrammed), they will follow the Segment 1 selection. If Segment 1 is
left as “0” and the feature is enabled, the NX8E will report “”A”.
LOC
56
52
PG
27
DESCRIPTION
DEFAULT
RESTORE COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY
Segment #1: Partition #1 Restore code
0
Segment #2: Partition #2 Restore code
0
Segment #3: Partition #3 Restore code
0
Segment #4: Partition #4 Restore code
0
Segment #5: Partition #5 Restore code
0
Segment #6: Partition #6 Restore code
0
Segment #7: Partition #7 Restore code
0
Segment #8: Partition #8 Restore code
0
DATA
_
_
_
_
_
_
_
_
NX-8E CONTROL
LOC
57
58
59
60
61
PG
27
27
27
27
27
LOC
PG
62
63
64
65
66
67
68
27
27
28
28
28
28
28
NX-8E CONTROL
DESCRIPTION
DEFAULT
BYPASS COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY
Segment #1: Partition #1 Bypass code
0
Segment #2: Partition #2 Bypass code
0
Segment #3: Partition #3 Bypass code
0
Segment #4: Partition #4 Bypass code
0
Segment #5: Partition #5 Bypass code
0
Segment #6: Partition #6 Bypass code
0
Segment #7: Partition #7 Bypass code
0
Segment #8: Partition #8 Bypass code
0
TAMPER COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY
Segment #1: Partition #1 Tamper Code
0
Segment #2: Partition #2 Tamper Code
0
Segment #3: Partition #3 Tamper Code
0
Segment #4: Partition #4 Tamper Code
0
Segment #5: Partition #5 Tamper Code
0
Segment #6: Partition #6 Tamper Code
0
Segment #7: Partition #7 Tamper Code
0
Segment #8: Partition #8 Tamper Code
0
TROUBLE COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY
Segment #1: Partition #1 Trouble Code
0
Segment #2: Partition #2 Trouble Code
0
Segment #3: Partition #3 Trouble Code
0
Segment #4: Partition #4 Trouble Code
0
Segment #5: Partition #5 Trouble Code
0
Segment #6: Partition #6 Trouble Code
0
Segment #7: Partition #7 Trouble Code
0
Segment #8: Partition #8 Trouble Code
0
SENSOR LOW BATTERY COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY
Segment #1: Partition #1 Sensor Low Battery Code
0
Segment #2: Partition #2 Sensor Low Battery Code
0
Segment #3: Partition #3 Sensor Low Battery Code
0
Segment #4: Partition #4 Sensor Low Battery Code
0
Segment #5: Partition #5 Sensor Low Battery Code
0
Segment #6: Partition #6 Sensor Low Battery Code
0
Segment #7: Partition #7 Sensor Low Battery Code
0
Segment #8: Partition #8 Sensor Low Battery Code
0
SENSOR MISSING COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY
Segment #1: Partition #1 Sensor Missing Code
0
Segment #2: Partition #2 Sensor Missing Code
0
Segment #3: Partition #3 Sensor Missing Code
0
Segment #4: Partition #4 Sensor Missing Code
0
Segment #5: Partition #5 Sensor Missing Code
0
Segment #6: Partition #6 Sensor Missing Code
0
Segment #7: Partition #7 Sensor Missing Code
0
Segment #8: Partition #8 Sensor Missing Code
0
DESCRIPTION
DURESS
AUXILIARY 1
AUXILIARY 2
KEYPAD PANIC
KEYPAD MULTIPLE CODE ENTRY TAMPER
BOX TAMPER / BOX TAMPER RESTORE
AC FAIL / AC RESTORE
DATA
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
DEFAULT
DATA
0-0
0-0
0-0
0-0
0-0
0-0-0-0
0-0-0-0
__
__
__
__
__
____
____
53
LOC
PG
69
70
71
72
73
74
75
76
77
28
28
28
28
28
29
29
29
29
78
29
79
80
81
82
83
84-87
88
89
29
29
29
29
29
29
30
30
90
30
54
DESCRIPTION
LOW BATTERY / LOW BATTERY RESTORE
POWER SHORT / POWER SHORT RESTORE
BELL TAMPER / BELL TAMPER RESTORE
TELEPHONE LINE CUT / LINE CUT RESTORE
GROUND FAULT / GROUND FAULT RESTORE
EXPANDER TROUBLE / EXP TROUBLE RESTORE
FAILURE TO COMMUNICATE
LOG FULL COMMUNICATOR CODE
OPENING CODE COMMUNICATOR CODE
Segment #1: Opening Code for Partition #1
Segment #2: Opening Code for Partition #2
Segment #3: Opening Code for Partition #3
Segment #4: Opening Code for Partition #4
Segment #5: Opening Code for Partition #5
Segment #6: Opening Code for Partition #6
Segment #7: Opening Code for Partition #7
Segment #8: Opening Code for Partition #8
CLOSING COMMUNICATOR CODE
Segment #1: Closing Code for Partition #1
Segment #2: Closing Code for Partition #2
Segment #3: Closing Code for Partition #3
Segment #4: Closing Code for Partition #4
Segment #5: Closing Code for Partition #5
Segment #6: Closing Code for Partition #6
Segment #7: Closing Code for Partition #7
Segment #8: Closing Code for Partition #8
AUTOTEST COMMUNICATOR CODE
RECENT CLOSING AND EXIT ERROR
START PROGRAMMING / END PROGRAMMING
END DOWNLOAD
CANCEL COMMUNICATOR CODE
RESERVED
PARTITION 1, ACCOUNT CODE
PARTITION 2, ACCOUNT CODE
PARTITION 2, FEATURE AND REPORTING SELECTION
Segment #1
1
Quick Arm
5
2
Re-Exit
6
3
Auto Bypass
7
4
Silent Panic
8
Segment #2
1
LED extinguish enable
5
2
Require user code for bypassing zones
6
3
Bypass sounder alert
7
4
AC power/low battery sounder alert
8
Segment #3
1
Open/Close
5
2
Bypass
6
3
Restore
7
4
Trouble
8
Segment #4
1
Late to Close / Early to Open
2-8 Reserved
Segment #5 RESERVED
DEFAULT
DATA
0-0-0-0
0-0-0-0
0-0-0-0
0-0-0-0
0-0-0-0
0-0-0-0
0-0
0-0
____
____
____
____
____
____
__
__
0
0
0
0
0
0
0
0
_
_
_
_
_
_
_
_
0
0
0
0
0
0
0
0
0-0
0-0
0-0-0-0
0-0-0-0
0
0-0-0-0
10-10-10-10-10-10
10-10-10-10-10-10
_
_
_
_
_
_
_
_
__
__
____
XX__
_
Reserved
_ ____
_ _ __ _ _
Audible Panic
Auxiliary 1
Auxiliary 2
Multi Keypress Tamper
Enables bypass toggle
Enables silent auto arm
Enables automatic instant
Reserved
Tamper
Cancel
Recent Closing
Exit Error
NX-8E CONTROL
LOC
91
92
93
94
95
96
PG
DESCRIPTION
DEFAULT
DATA
0
0
0
0
_
_
_
_
PARTITION 3, ACCOUNT CODE
PARTITION 3, FEATURE AND REPORTING SELECTION
Segment #1
1
Quick Arm
5
2
Re-Exit
6
3
Auto Bypass
7
4
Silent Panic
8
Segment #2
5
LED extinguish enable
1
6
Require user code for bypassing zones
2
7
Bypass sounder alert
3
8
AC power/low battery sounder alert
4
Segment #3
1
Open/Close
5
2
Bypass
6
3
Restore
7
4
Trouble
8
Segment #4
1
Late to Close / Early to Open
2-8 Reserved
Segment #5 RESERVED
PARTITION 3 ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segment #5 & #6 RESERVED
10-10-10-10-10-10
______
0
0
0
0
_
_
_
_
PARTITION 4, ACCOUNT CODE
PARTITION 4, FEATURE AND REPORTING SELECTION
Segment #1
5
Quick Arm
1
6
Re-Exit
2
7
Auto Bypass
3
8
Silent Panic
4
Segment #2
5
LED extinguish enable
1
6
Require user code for bypassing zones
2
7
Bypass sounder alert
3
8
AC power/low battery sounder alert
4
Segment #3
5
Open/Close
1
6
Bypass
2
7
Restore
3
8
Trouble
4
Segment #4
1
Late to Close / Early to Open
2-8 Reserved
Segment #5 RESERVED
10-10-10-10-10-10
______
30 PARTITION 2 ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segment #5 & #6 RESERVED
30
30
30
31
31
NX-8E CONTROL
Audible Panic
Auxiliary 1
Auxiliary 2
Multi Keypress Tamper
Enables bypass toggle
Enables silent auto arm
Enables automatic instant
Reserved
Tamper
Cancel
Recent Closing
Exit Error
Audible Panic
Auxiliary 1
Auxiliary 2
Multi Keypress Tamper
Enables bypass toggle
Enables silent auto arm
Enables automatic instant
Reserved
Tamper
Cancel
Recent Closing
Exit Error
55
LOC
PG
97
31
98
99
100
101
102
56
31
31
31
31
31
DESCRIPTION
DEFAULT
DATA
0
0
0
0
_
_
_
_
PARTITION 5, ACCOUNT CODE
PARTITION 5, FEATURE AND REPORTING SELECTION
Segment #1
5
Quick Arm
1
6
Re-Exit
2
7
Auto Bypass
3
8
Silent Panic
4
Segment #2
5
LED extinguish enable
1
6
Require user code for bypassing zones
2
7
Bypass sounder alert
3
8
AC power/low battery sounder alert
4
Segment #3
5
Open/Close
1
6
Bypass
2
7
Restore
3
8
Trouble
4
Segment #4
1
Late to Close / Early to Open
2-8 Reserved
Segment #5 RESERVED
PARTITION 5, ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segment #5 & #6 RESERVED
10-10-10-10-10-10
______
0
0
0
0
_
_
_
_
PARTITION 6, ACCOUNT CODE
PARTITION 6, FEATURE AND REPORTING SELECTION
Segment #1
1
Quick Arm
5
2
Re-Exit
6
3
Auto Bypass
7
4
Silent Panic
8
Segment #2
1
LED extinguish enable
5
2
Require user code for bypassing zones
6
3
Bypass sounder alert
7
4
AC power/low battery sounder alert
8
Segment #3
1
Open/Close
5
2
Bypass
6
3
Restore
7
4
Trouble
8
Segment #4
1
Late to Close / Early to Open
2-8 Reserved
Segment #5 RESERVED
10-10-10-10-10-10
______
PARTITION 4, ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segment #5 & #6 RESERVED
Audible Panic
Auxiliary 1
Auxiliary 2
Multi Keypress Tamper
Enables bypass toggle
Enables silent auto arm
Enables automatic instant
Reserved
Tamper
Cancel
Recent Closing
Exit Error
Audible Panic
Auxiliary 1
Auxiliary 2
Multi Keypress Tamper
Enables bypass toggle
Enables silent auto arm
Enables automatic instant
Reserved
Tamper
Cancel
Recent Closing
Exit Error
NX-8E CONTROL
LOC
PG
103
32
104
105
106
107
108
32
32
32
32
32
NX-8E CONTROL
DESCRIPTION
DEFAULT
DATA
0
0
0
0
_
_
_
_
PARTITION 7, ACCOUNT CODE
PARTITION 7, FEATURE AND REPORTING SELECTION
Segment #1
1
Quick Arm
5
2
Re-Exit
6
3
Auto Bypass
7
4
Silent Panic
8
Segment #2
1
LED extinguish enable
5
2
Require user code for bypassing zones
6
3
Bypass sounder alert
7
4
AC power/low battery sounder alert
8
Segment #3
1
Open/Close
5
2
Bypass
6
3
Restore
7
4
Trouble
8
Segment #4
1
Late to Close / Early to Open
2-8 Reserved
Segment #5 RESERVED
PARTITION 7, ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segment #5 & #6 RESERVED
10-10-10-10-10-10
______
0
0
0
0
_
_
_
_
PARTITION 8, ACCOUNT CODE
PARTITION 8, FEATURE AND REPORTING SELECTION
Segment #1
1
Quick Arm
5
2
Re-Exit
6
3
Auto Bypass
7
4
Silent Panic
8
Segment #2
1
LED extinguish enable
5
2
Require user code for bypassing zones
6
3
Bypass sounder alert
7
4
AC power/low battery sounder alert
8
Segment #3
1
Open/Close
5
2
Bypass
6
3
Restore
7
4
Trouble
8
Segment #4
1
Late to Close / Early to Open
2-8 Reserved
Segment #5 RESERVED
10-10-10-10-10-10
______
PARTITION 6, ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segment #5 & #6 RESERVED
Audible Panic
Auxiliary 1
Auxiliary 2
Multi Keypress Tamper
Enables bypass toggle
Enables silent auto arm
Enables automatic instant
Reserved
Tamper
Cancel
Recent Closing
Exit Error
Audible Panic
Auxiliary 1
Auxiliary 2
Multi Keypress Tamper
Enables bypass toggle
Enables silent auto arm
Enables automatic instant
Reserved
Tamper
Cancel
Recent Closing
Exit Error
57
LOC
PG
109
32
110
111
33
33
DESCRIPTION
DEFAULT
DATA
0
0
0
0
_
_
_
_
8
_
PARTITION 8, ENTRY/EXIT TIMERS
Segment #1 (Entry Time #1)
Segment #2 (Exit Time #1)
Segment #3 (Entry Time #2)
Segment #4 (Exit Time #2)
Segment #5 & #6 RESERVED
ZONE TYPE 1 ALARM EVENT CODE
ZONE TYPE 1 CHARACTERISTIC SELECT
Segment #1 (Circle numbers to program)
1 Fire (enable for fire zone).
2 24 Hour (enable for non-fire 24 hour
zone).
3 Keyswitch zone.
4 Follower (enable for burg zones that are
instant during non-entry times).
Segment #2 (Circle numbers to program)
1 Keypad audible on alarm.
2 Yelping siren on alarm.
3 Temporal siren on alarm.
4 Chime.
Segment #3 (Circle numbers to program)
1 Fast Loop Response.
2 Double End of Line Tamper zone.
3 Trouble zone (Day zone).
4 Cross Zone.
Segment #4 (Circle numbers to program)
1 Zone Activity Monitor.
2 End of Line Resistor Defeat.
3 Delays alarm activation 60 seconds.
4 Zone acts as request to exit input.
Segment #5 - Reserved
7
8
Delay 1 zone (enable to follow Timer 1 Entry/Exit
times).
Delay 2 zone (enable to follow Timer 2 Entry / Exit
times).
Interior (Enable for auto bypass or stay arming).
Local Only (enable if zone is not to be reported).
5
6
7
8
Bypassable.
Group Shunt.
Force armable.
Entry Guard.
5
6
7
8
Dialer Delay zone.
Swinger zone.
Restore reporting.
Listen-In.
5
6
7
8
Reserved.
Reserved.
Reserved.
Reserved.
5
6
THE DEFAULTS LISTED IN THE ODD NUMBERED LOCATIONS BELOW REPRESENT THE THREE SEGMENTS OF
EACH OF THOSE LOCATIONS. USE THE THREE SEGMENT CHARTS FROM LOCATION 111 TO UNDERSTAND
THESE DEFAULTS.
LOC
PG
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
33
33
33
33
34
34
34
34
34
34
34
34
34
34
34
34
34
34
58
DESCRIPTION
ZONE TYPE 2 ALARM EVENT CODE
ZONE TYPE 2 CHARACTERISTIC SELECT
ZONE TYPE 3 ALARM EVENT CODE
ZONE TYPE 3 CHARACTERISTIC SELECT
ZONE TYPE 4 ALARM EVENT CODE
ZONE TYPE 4 CHARACTERISTIC SELECT
ZONE TYPE 5 ALARM EVENT CODE
ZONE TYPE 5 CHARACTERISTIC SELECT
ZONE TYPE 6 ALARM EVENT CODE
ZONE TYPE 6 CHARACTERISTIC SELECT
ZONE TYPE 7 ALARM EVENT CODE
ZONE TYPE 7 CHARACTERISTIC SELECT
ZONE TYPE 8 ALARM EVENT CODE
ZONE TYPE 8 CHARACTERISTIC SELECT
ZONE TYPE 9 ALARM EVENT CODE
ZONE TYPE 9 CHARACTERISTIC SELECT
ZONE TYPE 10 ALARM EVENT CODE
ZONE TYPE 10 CHARACTERISTIC SELECT
DEFAULT
DATA
2
2-125-78-0-0
7
5-1245-5678-0-0
5
45-125-5678-0-0
5
457-125-5678-0-0
4
0-1245-5678-0-0
0
2-0-78-0-0
1
1-13-378-0-0
7
6-1245-5678-0-0
2
24-5-78-0-0
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
NX-8E CONTROL
LOC
PG
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
34
34
35
35
35
35
35
35
35
35
35
35
35
35
35
35
36
36
36
36
36
36
36
36
36
36
36
36
36
36
37
37
37
37
37
37
37
37
37
37
L
DESCRIPTION
ZONE TYPE 11 ALARM EVENT CODE
ZONE TYPE 11 CHARACTERISTIC SELECT
ZONE TYPE 12 ALARM EVENT CODE
ZONE TYPE 12 CHARACTERISTIC SELECT
ZONE TYPE 13 ALARM EVENT CODE
ZONE TYPE 13 CHARACTERISTIC SELECT
ZONE TYPE 14 ALARM EVENT CODE
ZONE TYPE 14 CHARACTERISTIC SELECT
ZONE TYPE 15 ALARM EVENT CODE
ZONE TYPE 15 CHARACTERISTIC SELECT
ZONE TYPE 16 ALARM EVENT CODE
ZONE TYPE 16 CHARACTERISTIC SELECT
ZONE TYPE 17 ALARM EVENT CODE
ZONE TYPE 17 CHARACTERISTIC SELECT
ZONE TYPE 18 ALARM EVENT CODE
ZONE TYPE 18 CHARACTERISTIC SELECT
ZONE TYPE 19 ALARM EVENT CODE
ZONE TYPE 19 CHARACTERISTIC SELECT
ZONE TYPE 20 ALARM EVENT CODE
ZONE TYPE 20 CHARACTERISTIC SELECT
ZONE TYPE 21 ALARM EVENT CODE
ZONE TYPE 21 CHARACTERISTIC SELECT
ZONE TYPE 22 ALARM EVENT CODE
ZONE TYPE 22 CHARACTERISTIC SELECT
ZONE TYPE 23 ALARM EVENT CODE
ZONE TYPE 23 CHARACTERISTIC SELECT
ZONE TYPE 24 ALARM EVENT CODE
ZONE TYPE 24 CHARACTERISTIC SELECT
ZONE TYPE 25 ALARM EVENT CODE
ZONE TYPE 25 CHARACTERISTIC SELECT
ZONE TYPE 26 ALARM EVENT CODE
ZONE TYPE 26 CHARACTERISTIC SELECT
ZONE TYPE 27 ALARM EVENT CODE
ZONE TYPE 27 CHARACTERISTIC SELECT
ZONE TYPE 28 ALARM EVENT CODE
ZONE TYPE 28 CHARACTERISTIC SELECT
ZONE TYPE 29 ALARM EVENT CODE
ZONE TYPE 29 CHARACTERISTIC SELECT
ZONE TYPE 30 ALARM EVENT CODE
ZONE TYPE 30 CHARACTERISTIC SELECT
DEFAULT
DATA
3
3-0-0-0-0
5
457-125-45678-0-0
4
0-12458-5678-0-0
7
5-12456-5678-0-0
5
457-1256-5678-0-0
4
0-12456-5678-0-0
7
5-1245-25678-0-0
5
457-125-25678-0-0
4
0-1245-25678-0-0
7
6-1245-25678-0-0
15
24-15-78
20
24-15-78
21
24-15-78
22
1-13-378
14
248-45-0-0-0
5
467-125-5678-0-0
5
457-1257-5678-0-0
7
6-12457-5678-0-0
5
457-125-5678-1-0
7
5-1245-5678-1-0
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
__
__ __ __ __ __
6-6-6-6-6-6-6-6
________
170
37 ZONES 49-56, ZONE TYPES
171
37 ZONES 49-56, PARTITION SELECTION (Segment 1=Zone 49 thru Segment 8=Zone 56)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
NX-8E CONTROL
8
1
2
3
4
5
6
7
8
59
LOC
L
L
L
L
60
PG
DESCRIPTION
DEFAULT
DATA
6-6-6-6-6-6-6-6
________
172
37 ZONES 57-64, ZONE TYPES
173
38 ZONES 57-64, PARTITION SELECTION (Segment 1=Zone 57 thru Segment 8=Zone 64)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
174
38 ZONES 65-72, ZONE TYPES
6-6-6-6-6-6-6-6
175
38 ZONES 65-72, PARTITION SELECTION (Segment 1=Zone 65 thru Segment 8=Zone 72)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
6-6-6-6-6-6-6-6
________
176
38 ZONES 73-80, ZONE TYPES
177
38 ZONES 73-80, PARTITION SELECTION (Segment 1=Zone 73 thru Segment 8=Zone 80)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
6-6-6-6-6-6-6-6
8
1
2
3
4
5
6
7
8
8
1
2
3
4
5
6
7
8
________
178
38
ZONES 81-88, ZONE TYPES
179
38
ZONES 81-88, PARTITION SELECTION (Segment 1=Zone 81 thru Segment 8=Zone 88)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
8
1
2
3
4
5
6
7
8
________
8
1
2
3
4
5
6
7
8
NX-8E CONTROL
LOC
L
L
L
L
PG
DESCRIPTION
DEFAULT
DATA
6-6-6-6-6-6-6-6
________
180
38 ZONES 89-96, ZONE TYPES
181
39 ZONES 89-96, PARTITION SELECTION (Segment 1=Zone 89 thru Segment 8=Zone 96)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
182
39 ZONES 97-104, ZONE TYPES
6-6-6-6-6-6-6-6
183
39 ZONES 97-104, PARTITION SELECTION (Segment 1=Zone 97 thru Segment 8=Zone 104)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
6-6-6-6-6-6-6-6
________
184
39 ZONES 105-112, ZONE TYPES
185
39 ZONES 105-112, PARTITION SELECTION (Segment 1=Zone 105 thru Segment 8=Zone 112)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
8
1
2
3
4
5
6
7
8
________
186
39
ZONES 113-120, ZONE TYPES
187
39
ZONES 113-120, PARTITION SELECTION (Segment 1=Zone 113 thru Segment 8=Zone 120)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
NX-8E CONTROL
6-6-6-6-6-6-6-6
8
1
2
3
4
5
6
7
8
8
1
2
3
4
5
6
7
8
________
8
1
2
3
4
5
6
7
8
61
LOC
L
L
L
L
62
PG
DESCRIPTION
DEFAULT
DATA
6-6-6-6-6-6-6-6
________
188
39 ZONES 121-128, ZONE TYPES
189
39 ZONES 121-128, PARTITION SELECTION (Segment 1=Zone 121 thru Segment 8=Zone 128)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
190
40 ZONES 129-136, ZONE TYPES
6-6-6-6-6-6-6-6
191
40 ZONES 129-136, PARTITION SELECTION (Segment 1=Zone 129 thru Segment 8=Zone 136)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
6-6-6-6-6-6-6-6
________
192
40 ZONES 137-144, ZONE TYPES
193
40 ZONES 137-144, PARTITION SELECTION (Segment 1=Zone 137 thru Segment 8=Zone 144)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
6-6-6-6-6-6-6-6
8
1
2
3
4
5
6
7
8
8
1
2
3
4
5
6
7
8
________
194
40
ZONES 145-152, ZONE TYPES
195
40
ZONES 145-152, PARTITION SELECTION (Segment 1=Zone 145 thru Segment 8=Zone 152)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
8
1
2
3
4
5
6
7
8
________
8
1
2
3
4
5
6
7
8
NX-8E CONTROL
LOC
L
L
L
L
PG
DESCRIPTION
DEFAULT
DATA
6-6-6-6-6-6-6-6
________
196
40 ZONES 153-160, ZONE TYPES
197
40 ZONES 153-160, PARTITION SELECTION (Segment 1=Zone 153 thru Segment 8=Zone 160)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
198
41 ZONES 161-168, ZONE TYPES
6-6-6-6-6-6-6-6
199
41 ZONES 161-168, PARTITION SELECTION (Segment 1=Zone 161 thru Segment 8=Zone 168)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
6-6-6-6-6-6-6-6
________
200
41 ZONES 169-176, ZONE TYPES
201
41 ZONES 169-176, PARTITION SELECTION (Segment 1=Zone 169 thru Segment 8=Zone 176)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
8
1
2
3
4
5
6
7
8
________
202
41
ZONES 177-184, ZONE TYPES
203
41
ZONES 177-184, PARTITION SELECTION (Segment 1=Zone 177 thru Segment 8=Zone 184)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
NX-8E CONTROL
6-6-6-6-6-6-6-6
8
1
2
3
4
5
6
7
8
8
1
2
3
4
5
6
7
8
________
8
1
2
3
4
5
6
7
8
63
LOC
L
DESCRIPTION
DEFAULT
DATA
6-6-6-6-6-6-6-6
________
204
41 ZONES 185-192, ZONE TYPES
205
41 ZONES 185-192, PARTITION SELECTION (Segment 1=Zone 185 thru Segment 8=Zone 192)
Segments
1
2
3
4
5
6
7
1
1
1
1
1
1
1
Partition #1
2
2
2
2
2
2
2
Partition #2
3
3
3
3
3
3
3
Partition #3
4
4
4
4
4
4
4
Partition #4
5
5
5
5
5
5
5
Partition #5
6
6
6
6
6
6
6
Partition #6
7
7
7
7
7
7
7
Partition #7
8
8
8
8
8
8
8
Partition #8
206
207
208
209
210
64
PG
42 DAYS OF THE WEEK "AUTO DISARMING" WILL OCCUR IN PARTITIONS 1-8
Segments
1
2
3
4
5
6
1
1
1
1
1
1
Sunday
2
2
2
2
2
2
Monday
3
3
3
3
3
3
Tuesday
4
4
4
4
4
4
Wednesday
5
5
5
5
5
5
Thursday
6
6
6
6
6
6
Friday
7
7
7
7
7
7
Saturday
8
8
8
8
8
8
Reserved
42 SERIAL PORT ENABLE
0
0 = Disabled
1 = Home Automation Protocol Enabled
2 = Serial Printer Mode
42 SERIAL PORT BAUD RATE
2
0 = 2400 (2.4K)
3 = 19200 (19.2K)
1 = 4800 (4.8K)
4 = 38400 (38.4K)
2 = 9600 (9.6K)
5-7 = Reserved
42 HOME AUTOMATION PROTOCOL
Off
LED Off = Binary LED On = ASCII
42 NX8E TRANSITION-BASED BROADCASTS
Segment #1
Segment #2
1 = System Status Message
1 = Reserved
2 = X-10 Message Received
2 = Interface Configuration
3 = Log Event Message
3-4 = Reserved
4 = Keypad Message Received
5 = Zone Status Message
5 –8 = Reserved
6 = Zones Snapshot Message
7 = Partition Status Message
8 = Partitions Snapshot Message
7
1
2
3
4
5
6
7
8
_
8
1
2
3
4
5
6
7
8
8
1
2
3
4
5
6
7
8
NX-8E CONTROL
211
212
43 NX-584 COMMAND/REQUEST ENABLE
Segment #1
1 = Reserved
2 = Interface Configuration Request
3 = Reserved
4 = Zone Name Request
5 = Zone Status Request
6 = Zones Snapshot Request
7 = Partition Status Request
8 = Partitions Snapshot Request
Segment #3
1 = Program Data Request
2 = Program Data Command
3 = User Information Request with PIN
4 = User Information Request without PIN
5 = Set User Code Command with PIN
6 = Set User Code Command without PIN
7 = Set User Authorization Comm with PIN
8 = Set User Authorization Comm without PIN
44 LCD KEYPAD ADDRESS FOR NX-584
Segment #2
1 = System Status Request
2 = Send X-10 Message
3 = Log Event Request
4 = Send Keypad Text Message
5 = Keypad Terminal Mode Request
6-8 = Reserved
Segment #4
1-2 = Reserved
3 = Store Communication Event Command
4 = Set Clock / Calendar Command
5 = Primary Keypad Function with PIN
6 = Primary Keypad Function without PIN
7 = Secondary Keypad Function
8 = Zone Bypass Toggle
192
KP PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
1
192
193
194
195
196
197
198
199
2
200
201
202
203
204
205
206
207
3
208
209
210
211
212
213
214
215
4
216
217
218
219
220
221
222
223
5
224
225
226
227
228
229
230
231
6
232
233
234
235
236
237
238
239
7
240
241
242
243
244
245
246
247
8
248
249
250
251
252
253
254
255
213
NX-8E CONTROL
RESERVED
65
XIII.
66
NX-8E WIRING DIAGRAM
NX-8E CONTROL
XIV.
TERMINAL DESCRIPTIONS
TERMINAL
R1
R
T
T1
EARTH
AC
BELL + &
BELL -
KP DATA
KP COM
KP POS
SMOKE+
COM
AUX PWR+
ZONE 8
COM
ZONE 7
ZONE 6 ZONE 1
RELAY
C
2
NO
COM
RELAY
NC
1
C
(See terminal
drawing)
DESCRIPTION
House Telephone Ring (Grey).
Telephone Ring (Red).
Telephone Tip (Green).
House Telephone Tip (Brown).
Earth Ground. Connect to a cold water pipe or a 6 to 10 foot driven rod.
AC input. Connect to a 16.5V, 40VA or 50 VA Class ll U.L. approved transformer.
If used as a siren output (default), the speaker rating should be 15 watt at 8 or 16 ohm, or 30/40
watt at 4, 8, or 16 ohms. If voltage output is selected in location 37, this output becomes voltage
output, 12VDC, 1 Amp maximum load. NOTE: A 3.3K Ω resistor may be required across the
bell terminals when a 12 VDC siren is used. If no resistor is used, you may experience
voltage leakage into the siren, which will cause these devices to output a small signal.
Connect to the data terminal on the keypads and the expanders. Maximum number of devices
(keypads + expanders) is 32. See AMaximum Wire Run@ chart below.
Connect to the Common terminal on the keypads and the expanders.
Connect to the POS terminal on the keypads and the expanders. Individually, this terminal is
limited to 1 Amp. Combined, this terminal and AUX PWR + are limited to 2 amps total current.
Smoke detector power 12VDC, 1.5 amps maximum (For those jurisdictions which allow the Priority
zone to be used with smoke detectors.)
Connect negative wire of powered devices such as motion detectors and smoke detectors.
Connect positive wire of all powered devices except smoke detectors and keypads. Individually,
this terminal is limited to 1 Amp. Combined, this terminal and KP POS are limited to 2 amps total
current.
Connect to one side of zone 8 loop. Connect the other side to com terminal. Open or short causes
alarm. Zone 8 may be used for a two-wire smoke detector using a 680 Ω E.O.L. resistor.
Connect one side to AUX PWR+ ONLY if using 2-wire smoke. Refer to wiring diagram.
Program location 37, segment 6, option 1.
Common (-) terminal for zones 7 & 8. (See the wiring diagram for examples.)
Connect to one side of zone 7 loop. Connect the other side to COM terminal. Open or short causes
alarm.
Connect as described for zones 7 & 8. Only zone 8 can be a two-wire zone. (See the wiring
diagram for examples.)
Closed dry contact rated 1 Amp at 30 Volts.
NOTE: These terminals can be
Normally open dry contact rated 1 Amp at 30 Volts.
set for 12VDC. Install J12 for
Common used to ground any devices connected to relays.
AUX1 and J13 for AUX2 (See
Normally closed dry contact rated 1 Amp at 30 Volts
terminal drawing.)
Closed dry contact rated 1 Amp at 30 Volts
Connect negative lead of low current device [relay, LED (install 1kΩ resistor in series
AUX 1- with LED), etc.]. Connect positive lead of device to AUX PWR +. Current is limited to
AUX 4
50mA when output is negative, and 250FA when output is positive. Part number #8920
is 4-wire cable.
KEYPAD MAXIMUM WIRE RUN
(Note: These numbers are for one keypad at the end of the wire. When connecting more than one keypad to the end
of the wire, a higher gauge wire will be required.)
Length in feet
250
500
1000
1500
2500
NX-8E CONTROL
WHEN CONNECTED TO NX-8E
WHEN CONNECTED TO NX320-E
Wire Gauge
24
20
18
16
14
Wire Gauge
22
18
16
14
12
67
ZONE WORKSHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
68
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
NX-8E CONTROL
XV.
APPENDIX 1
REPORTING FIXED CODES IN CONTACT ID AND SIA
The table lists the event codes sent for the following reports (if enabled) when using CONTACT ID or SIA formats.
REPORT
MANUAL TEST
AUTOTEST
OPEN (user number)
CLOSE (user number)
CANCEL (user number)
DOWNLOAD COMPLETE
START PROGRAM
END PROGRAM
GROUND FAULT
GROUND FAULT RESTORE
RECENT CLOSE (user number)
EXIT ERROR (user number)
EVENT LOG FULL
FAIL TO COMMUNICATE
EXPANDER TROUBLE (device number)
EXPANDER RESTORE (device number)
TELEPHONE FAULT
TELEPHONE RESTORE
SIREN TAMPER (device number)
SIREN RESTORE (device number)
AUX POWER OVER CURRENT (device number)
AUX POWER RESTORE (device number)
LOW BATTERY (device number)
LOW BATTERY RESTORE (device number)
AC FAIL (device number)
AC RESTORE (device number)
BOX TAMPER (device number)
BOX TAMPER RESTORE (device number)
KEYPAD TAMPER
KEYPAD PANIC (audible)
KEYPAD PANIC (silent)
DURESS
KEYPAD AUXILIARY 1
KEYPAD AUXILIARY 2
RF SENSOR LOST (zone number)
RF SENSOR RESTORE (zone number)
SENSOR LOW BATTERY (zone number)
SENSOR BATTERY RESTORE (zone number)
ZONE TROUBLE (zone number)
ZONE TROUBLE RESTORE (zone number)
ZONE TAMPER (zone number)
ZONE TAMPER RESTORE (zone number)
ZONE BYPASS (zone number)
BYPASS RESTORE (zone number)
EARLY OPEN/LATE CLOSE
FAIL TO CLOSE
ZONE ACTIVITY FAULT
ZONE ACTIVITY RESTORE
CONTACT ID
601
602
401
401
406
412
627
628
310
310
401
457
605
354
333
333
351
351
321
321
312
312
309
309
301
301
137
137
137
120
121
121
110
100
381
381
384
384
380
380
137
137
570
570
451
454
391
391
SIA
RX
RP
OP
CL
OC
RS
LB
LX
GF
GK
CR
EE
JL
RT
ET
ER
LT
LR
YA
YH
YP
YQ
YT
YR
AT
AR
TA
TR
TA
PA
HA
HA
FA
MA
*T
*R
XT
XR
*T
*R
TA
TR
*B
*U
OK
CI
NA
NS
THE NUMBER IN PARENTHESES FOLLOWING THE EVENT IS THE NUMBER THAT WILL BE REPORTED AS
THE ZONE NUMBER. IF THERE ARE NO PARENTHESES, THE ZONE WILL BE A0". SEE PAGE 71 FOR THE
DEVICE NUMBERS.
* The character transmitted in this slot will be the first character from the event code of the zone that is
bypassed or in trouble. (See locations 110 - 141)
NX-8E CONTROL
69
XVI.
APPENDIX 2
REPORTING ZONE CODES IN SIA OR CONTACT ID
The NX-8E has the ability to report SIA level 1 transmissions to either or both phone numbers. Each report in SIA consists
of an Event Code and a Zone or User ID. The Zone ID will be the zone number that is in alarm. The event code will come
from the chart below and be programmed in the zone type event code.
Programmed Event Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
SIA Code
HA
FA
PA
BA
BA
BA
UA
BA
BA
UA
HA
MA
PA
TA
RP
GA
KA
WA
QA
SA
ZA
KH
FA
Description
Holdup Alarm
Fire Alarm
Panic alarm
Burglary Alarm
Burglary Alarm
Burglary Alarm
Untyped Alarm
Burglary Alarm
Burglary Alarm
Untyped Alarm
Holdup Alarm
Medical Alarm
Panic alarm
Tamper Alarm
Periodic Test
Gas Alarm
Heat Alarm
Water Alarm
Emergency Alarm
Sprinkler Alarm
Freeze Alarm
High Temp Alarm
Manual Fire Alarm
The NX-8E has the ability to report Ademco Contact ID transmissions. Each report in Contact ID consists of an Event Code
and a Zone ID. The zone ID is the zone that created the alarm. The event code will come from the chart below and be
programmed in the zone type event code.
Programmed Event Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
70
Contact ID Code
122
110
120
130
131
132
133
134
135
150
121
100
123
137
602
151
158
154
140
140
159
158
115
Description
Silent Panic
Fire Alarm
Panic alarm
Burglary Alarm
Perimeter Alarm
Interior Alarm
24 Hour Burglary
Entry Alarm
Day/Night Alarm
Non Burglary 24 Hour
Duress Alarm
Medical Alarm
Audible Panic Alarm
Tamper Alarm
Periodic Test
Gas Detected
High Temp
Water Leakage
General Alarm
General Alarm
Low Temp
High Temp Alarm
Manual Fire Alarm
NX-8E CONTROL
XVII.
APPENDIX 3
EXPANDER NUMBERS FOR REPORTING EXPANDER TROUBLE
The tables below list the device numbers that will be reported for trouble conditions.
Device
NX-8E Control Panel
NX-534E Two Way Listen-In
NX-540E “Operator”
NX-591E Cellemetry Interface
NX-870E Fire Supervision
Device # reported
0
64
40
76
9
See page 69 for possible report codes.
KEYPADS
KEYPAD
1
2
3
4
5
6
7
8
PART 1
192
200
208
216
224
232
240
248
PART 2
193
201
209
217
225
233
241
249
PART 3
194
202
210
218
226
234
242
250
PART 4
195
203
211
219
227
235
243
251
HARDWIRE EXPANDER (NX-216E)
Starting zone number
Expander # reported
Zone 09 (All switches off)
22
Zone 09 (Switch 1 on)
23
Zone 17 (Switch 2 on)
16
Zone 25 (Switches 1 & 2 on)
17
Zone 33 (Switch 3 on)
18
Zone 41 (Switches 1 & 3 on)
19
Zone 49 (Switches 2 & 3 on)
20
Zone 57 (Switches 1, 2 & 3 on)
21
Zone 65 (Switch 4 on)
96
Zone 73 (Switches 1 & 4 on)
97
Zone 81 (Switches 2 & 4 on)
98
Zone 89 (Switches 1, 2 & 4 on)
99
PART 5
196
204
212
220
228
236
244
252
PART 6
197
205
213
221
229
237
245
253
PART 7
198
206
214
222
230
238
246
254
PART 8
199
207
215
223
231
239
247
255
Starting zone number
Expander # reported
Zone 97 (Switches 3 & 4 on)
100
Zone 105 (Switches 1, 3 & 4 on)
101
Zone 113 (Switches 2, 3 & 4 on)
102
Zone 121 (Switches 1, 2, 3 & 4 on)
103
Zone 129 (Switch 5 on)
104
Zone 137 (Switches 1 & 5 on)
105
Zone 145 (Switches 2 & 5 on)
106
Zone 153 (Switches 1, 2 & 5 on)
107
Zone 161 (Switches 3 & 5 on)
108
Zone 169 (Switches 1, 3 & 5 on)
109
Zone 177 (Switches 2, 3 & 5 on)
110
Zone 185 (Switches 1, 2, 3 & 5 on)
111
REMOTE POWER SUPPLY (NX-320E)
Switch Setting
Address
All switches off
84
Switch 1 on
85
Switch 2 on
86
Switch 1 & 2 on
87
Switch 3 on
88
Switch 1 & 3 on
89
Switch 2 & 3 on
90
Switches 1, 2, & 3 on
91
WIRELESS RECEIVER (NX-448E)
Switch Setting
Expander # reported
All switches off
35
Switch 1 on
36
Switch 2 on
37
Switches 1 & 2 on
38
Switch 3 on
39
Switches 1 & 3 on
32
Switches 2 & 3 on
33
Switch 1, 2 & 3 on
34
OUTPUT MODULE (NX-508E)
Switch Setting
Switch 1 & 2 on
Switch 3 on
Switch 1 & 3 on
Switch 2 & 3 on
Switch Setting
Switch 1,2,&3 on
All switches off
Switch 1 on
Switch 2 on
NX-8E CONTROL
Address
24
25
26
27
Address
28
29
30
31
71
XVIII.
APPENDIX 4
USER ID OR ZONE ID HEX DIGIT FOR 4+2 FORMATS
The following appendix applies only to slow formats (locations 56- 83 lower digit). The digit programmed in the
locations will be sent as the upper HEX digit in place of the alarm event code. The zone ID or user ID will always be
reported as the lower HEX digit (1-F) as shown in the chart below. For example, if the zone ID or user ID is 15, the 4+2
lower digit will be “F” and if the zone ID or user ID is 166, the 4+2 digit will be “1”. Use the chart shown below for
convenience. NOTE: If Segments 2-8 are left as “0” (unprogrammed), they will follow the Segment 1 selection. If
Segment 1 is left as “0” and the feature is enabled in Location 23, the NX8E will report “A”.
ZONE
USER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
72
HEX
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
ZONE
USER
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
HEX
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
ZONE
USER
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
HEX
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
ZONE
USER
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
HEX
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
ZONE
USER
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
HEX
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
ZONE
USER
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
HEX
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
NX-8E CONTROL
XIX.
TELEPHONE COMPANY INTERFACE INFORMATION
TELEPHONE CONNECTION REQUIREMENTS
Except for telephone company provided ringers, all connections to the telephone network shall be made through
standard plugs and standard telephone company provided jacks or equivalent in such a manner as to allow for
immediate disconnection of the terminal equipment. Standard jacks shall be so arranged that if the plug connected
thereto is withdrawn, no interference to the operation of the equipment at the customer’s premises, which remains
connected to the telephone network, shall occur by reason of such withdrawal.
INCIDENCE OF HARM
Should terminal equipment or protective circuitry cause harm to the telephone network, the telephone company shall,
where practical, notify the customer that temporary discontinuance of service may be required. However, where prior
notice is not practical, the telephone company may temporarily discontinue service if such action is deemed reasonable
in the circumstances. In the case of such temporary discontinuance, the telephone company shall promptly notify the
customer who will be given the opportunity to correct the situation. The customer also has the right to bring a complaint
to the FCC if he feels the disconnection is not warranted.
CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES
The telephone company may make changes in its communications facilities, equipment, operations, or procedures
where such action is reasonably required and proper in its business. Should any such change render the customers
terminal equipment incompatible with the telephone company facilities, the customer shall be given adequate notice to
make modifications to maintain uninterrupted service.
GENERAL
The FCC prohibits customer-provided terminal equipment to be connected to party lines.
IMPORTANCE OF THE RINGER EQUIVALENCE NUMBER
The Ringer Equivalence Number (REN) of this device is 0.1B. This number is a representation of the electrical load that
it applies to your telephone line.
MALFUNCTION OF THE EQUIPMENT
In the event that the device should fail to operate properly, the customer shall disconnect the equipment from the
telephone line to determine if it is the customers’ equipment that is not functioning properly. If the problem is with the
device, the customer shall discontinue use until it is repaired.
EQUIPMENT INFORMATION
MANUFACTURER OF CONNECTING EQUIPMENT: CADDX CONTROLS, INC.
FCC REGISTRATION NUMBER: GCQUSA-31771-AL-T, RINGER EQUIVALENCE: 0.1 B
INDUSTRY CANADA INFORMATION
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets
telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the
user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions might not prevent degradation of service in some
situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or
alternations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their protection that the electrical ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in
rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electrical
inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number (REN) of this device is 0.1B. This number is a representation of the electrical load that it
applies to your telephone line. NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed 5.
NX-8E CONTROL
73
XX.
NOTICES
(Applies to products which have the CE mark
attached)
DECLARATION OF CONFORMITY
Manufacturer’s Name:
Caddx Controls
Manufacturer’s Address: 1420 North Main Street
Gladewater Texas 75647
EU Representative:
Interlogix Europe
Product Identification
Product:
Model Numbers:
Brand:
NetworX
NX-8E
CADDX
R&TTE Directive
See EMC and LVD tests below
Network Compatibility Declaration
We declare under our sole responsibility that this product
is designed to work with the networks in the countries
marked with a check () and may have interworking
problems with the countries that are not checked. Due to
the inherent differences in the individual PSTNs, certain
software settings may need to be adjusted on a countryto-country basis. If it is desired to use this equipment on
a network other than the one on which it was originally
installed, you should contact your equipment supplier.
() Austria
() Belgium
() Denmark
() Finland
() France
() Germany
() Greece
() Iceland
() Ireland
() Italy
(_) Liechtenstein
() Luxembourg
() Netherlands
() Norway
() Poland
() Portugal
() Spain
() Sweden
() Switzerland
() United Kingdom
EMC Directive
EN50081-1
EN50130-4
EN55022
EN60950
EN61000-3-2
EN61000-3-3
LVD Directive
EN 60950: 1999-4 3rd edition
Means of Conformity
We declare under our sole responsibility that this product
is in conformity with Directive 1999/5/EC (R&TTE);
Directive 73/23/EEC (LVD); and Directive 89/336/EEC
(EMC) and based on test results using (non)-harmonized
standards in accordance with the Directives mentioned.
Telecom Approval Notice
This equipment has been approved in accordance with
the Council Decision 98/482/EC for pan-European, single
terminal connection to the public switched telephone
network (PSTN). However, due to the differences
between the individual PSTNs provided in different
countries, the approval does not, of itself, give an
unconditional assurance of successful operation on every
PSTN network termination point. In the event of
problems, you should contact your equipment supplier in
the first instance.
Electrical Requirements
This device automatically adjusts to voltages within the
range of 230 V 50/60 Hz.
Fuse: Type T 200mA 250 VAC
Additional Tests
This equipment has been tested and found to comply
with the following standards (which are no longer
required for compliance).
74
NX-8E CONTROL
XXI.
UNDERWRITERS LABORATORIES INFORMATION
The NetworX NX-8E holds the following listings from Underwriters Laboratories (US and Canadian):
UL609
CAN/ULC-S303-M91
UL985
CAN/ULC-S545-M89
UL1023
ORD-C1023-1974
UL1610
CAN/ULC-S304-M88
UL1637
Local Grade A Mercantile, Police Station Connect with Basic Line Security
* requires #NX-003-C enclosure
Household Fire
Household Burglary
Grade B & C Central Station Burglar Alarm Unit
Home Health Care Signaling
WHEN INSTALLING AN NX-8E IN COMPLIANCE WITH UNDERWRITERS LABORATORIES, THE
FOLLOWING INSTRUCTIONS MUST BE OBSERVED:
• Initiating and indicating devices must be rated at 11.5 to 12.4 V DC residential, 12.0 V DC commercial.
• When using partitioning in Commercial Burglary applications, the main control must be protected by a 24-hour alarm
circuit.
• Force Arming and Auto Arming shall not be enabled.
• For residential fire applications, the indicating devices shall be a Wheelock 34T-12 or equivalent.
• The "Listen-In" feature shall not be enabled.
• The Siren/Bell Test shall be enabled. The auxiliary outputs controlling the audible device require a minimum cutoff
time of 15 minutes for commercial burglary, 4 minutes for residential applications, or 30 minutes for Commercial
Burglary for Canada.
• For residential fire installations, the Dynamic Battery Test time cannot exceed four (4) hours.
• Ringback shall be enabled on UL commercial burglary installations.
• On commercial burglary installations, the fire initiating circuits shall not be connected.
• The Entry-Guard feature shall be disabled.
• Swinger Shutdown shall be disabled.
• Group Bypassing shall be disabled.
• Delay before dial seizure shall be set to "0".
• Total current draw from aux power connections at terminal positions POS, AUX PWR, and SMOKE PWR must not
exceed 400 mA.
• Remote Downloading shall not be used on UL listed systems.
• For residential burglary applications, the maximum entry and exit delay times shall be 45 and 60 seconds respectively.
The exit delay time shall not exceed 60 seconds for commercial burglar alarm applications.
• The keyswitch option shall not be used.
• The telephone line monitor shall be enabled.
• The Telephone Line Cut delay shall not exceed 90 seconds.
• 24-hour communicator test transmission is required.
• For 24 hours of standby power using a 7.0 AH battery, limit auxiliary power load to 140 mA.
• For 24 hours of standby power using a 17.2 AH battery, limit auxiliary power load to 400 mA.
• The silent keypad option shall not be enabled.
• UL has only verified compatibility with the following listed DACRs and formats: Sure-Gard SG-MLR2-DG:
2,9,10,12,13,14; Silent Knight 9000 - 2,12; FBI - CP220FBI, 13; and Ademco 685: 2,11,12, and 13.
• For burglary installations, cross-zoned detectors shall overlap 100 percent in the area of coverage and similar
coverage areas must be used. For example, interior protection is cross-zoned with interior protection, and so on.
• Expander trouble must activate the siren (Loc. 37, Segment 2, LED 2)
• For UL 1637, expander trouble must activate keypad sounder (Loc. 39, Segment 1, LED 8)
NX-8E CONTROL
75
• If the Late to Close/Early to Open feature is enabled, the Opening and Closing reports shall be enabled (Loc. 23, Seg.
4, Option 1 and Loc. 23, Seg. 3, Option 1).
• For Canadian installations, the class II transformer secure tab shall not be employed.
MINIMUM SYSTEM CONFIGURATIONS FOR UL INSTALLATIONS
(Residential Fire, Residential Burglary, Commercial Burglary)
• The NetworX NX-8E panel is necessary to initiate Residential and Commercial installations.
• At least one compatible keypad is needed for all applications.
• At least one bell fixture is required for all applications, except Grade C Central Station. For Grade A Local, the AD1012 bell and Grade A bell housing shall be used.
• Commercial UL applications require #NX-003-C metal enclosure. Supplied screws to be used.
• A minimum of two (2) keypads is required for Home Health applications and each keypad must be set to a unique
address.
• The wireless devices are only UL listed for residential applications.
• The DACT shall be enabled for all commercial burglary applications.
STANDBY TIME
24 hours
TOTAL AUXILIARY
CURRENT
1.9 Amps
1.25 Amps
600 mA
48 hours
900 mA
600 mA
300 mA
72 hours
600 mA
400 mA
200 mA
• Calculations based on three 17-Amp batteries.
STANDBY BATTERY
CAPACITY
ALARM CURRENT
51 AH
34 AH
17 AH
51 AH
34 AH
17 AH
51 AH
34 AH
17 AH
600 mA
1 Amp
1 Amp
1 Amp
1 Amp
1 Amp
1 Amp
1 Amp
1 Amp
K
IMPORTANT!
1. If separate power supplies are necessary to accommodate additional devices, safety standards
require that each power supply be prominently marked with adequate instructions for removing all
power from the unit.
2. Dispose of used batteries according to the manufacturer’s instructions and/or local government
authorities.
3. Installation personnel should thoroughly read and understand the installation instructions and the
users manuals for the panel and all the accessories to be included with the system before attempting
to install a security system.
WARNING!
Replace only with Panasonic #LC12V4BP or Yuasa #NP4-12 battery. Observe polarity when installing a
new battery. Installing the battery backwards may cause damage to the panel. There is a risk of explosion
if the battery is replaced with an incorrect type.
NOTE
Electrical codes will vary depending upon the country and city where the system is installed. It is the
installer’s responsibility to ensure that the electrical installation is safe and conforms to all applicable
codes, laws, or regulations. Only qualified persons should connect this device to the mains supply.
76
NX-8E CONTROL
XXII.
BOARD INSTALLATION
Inside the can, several 2-holed insertion points have been constructed. This
allows for either vertical or horizontal placement of the modules. Notice that
each insertion point has two sizes of holes -a larger hole and a smaller hole.
Diagram 1: The black plastic PCB guides are grooved on one edge where the
PC board will be seated. The end with the half-moon protrusion fits into the
larger hole. The smaller hole is for the screw.
Diagram 2: Place the first black plastic PCB guide in the top insertion point,
grooved edge downward. The half-moon protrusion will be in the large hole. It
does not require force. Insert one of the provided screw into the smaller hole
(from inside the can) to secure it in place. A screwdriver should reach through
the notch that runs the length of the guide to tighten the screw. The second
PBC guide should be positioned opposite the first (grooved edge up) and placed
in the lower insertion point, using the same procedures described above. Once
mounted, screw it in securely.
Diagram 3: The PC Board should slide freely in the grooves of both guides.
NX-8E CONTROL
77
XXIII.
SPECIFICATIONS
OPERATING POWER
16.5 VAC, 40 or 50 VA Transformer
AUXILIARY POWER
w/40 or 50 VA Transformer
w/NX-320 Power Supply
12 VDC Regulated 2 AMP
12 VDC Regulated 2 AMPS + Control
Panel Power
LOOP RESISTANCE
Standard Loop
2-Wire Smokes
300 Ohms Maximum
30 Ohms Maximum
BUILT-IN SIREN DRIVER
2-tone (Temporal and Yelp)
LOOP RESPONSE
Selectable 50mS or 500mS
OPERATING TEMPERATURE
32 to 120 degrees F
LED KEYPAD
Current Draw
Zones Normal w/o Sounder
Dimensions
NX148E LCD KEYPAD
Current Draw
w/o Sounder
Dimensions
130 mA max.
55 mA
6.4" Wide
4.0" High
1.1" Deep
110 mA max.
75 mA
6.4" Wide
5.3" High
1.0" Deep
METAL ENCLOSURE DIMENSION
11.25" Wide
11.25" High
3.50" Deep
SHIPPING WEIGHT
9 lbs.
GE INTERLOGIX
1420 NORTH MAIN STREET
GLADEWATER, TEXAS 75647
www.caddx.com
Main
Outside the US
Main Fax
NX-8E INSTALLATION MANUAL
NX8EIG02
REV. G (12-02-02)
800-727-2339
903-845-6941
903-845-6811
Technical Support
Tech Support Fax
Sales & Literature
800-727-2339
903-845-8409
800-547-2556
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising