PORTSMOUTH™ Installation Instructions 4285.001

PORTSMOUTH™ Installation Instructions 4285.001
Installation
Instructions
PORTSMOUTH™
4285.001
4285.001F15
SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
M965472 REV. 1.2 (12/14)
Recommended tools
Phillips Screwdriver
Regular Screwdriver
1
Adjustable Wrench
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
Plumbers' Putty or Caulking
Turn off hot and cold water
supplies before beginning.
Make certain the SEAL (9) is properly seated in recess of spout base.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and
mounting surface. Do not use putty.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
7
A
7
B
9
10
1
9
PUTTY
3
2
2
3
4
SINK OR
MOUNTING
S U R FA C E
4
5
5
8
6
8
6
2
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
2
1
Faucet supplies are 21" long from faucet base.
COLD
Note: If additional supply length is
required, installer must purchase
additional parts separately.
HOT
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
3
INSTALL SPRAY HOLDER
On model with separate spray, place the SPRAY HOLDER (1)
into the appropriate mounting hole. Assemble the SPRAY
HOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1)
from below and hand tighten. Do not use putty.
For installation less spray, cap off SPRAY HOSE
CONNECTION (3) with PIPE CAP (4).
1
5
CONNECT HOSE SPRAY
Feed SPRAY HOSE (5) through SPRAY
HOLDER (1) and attach COUPLING NUT (6)
of HOSE (5) to SPRAY HOSE CONNECTION (3)
on valve body. Tighten COUPLING NUT (6)
firmly.
SPRAY HOSE
CONNECTION
3
2
4
6
4
TEST INSTALLED FAUCET
2
3
Move HANDLE down into "off" position and remove
AERATOR (1).
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
For faucet with spray, direct SPRAY HEAD (3) into sink and
activate SPRAY (3). Check hose connections for leaks.
Move HANDLE (2) down to "off" position and replace
AERATOR (1).
1
CHECK CONNECTIONS
FOR LEAKS
M965472 REV. 1.2 (12/14)
5
SERVICE
Reduced flow. If the flow gradually reduces over a number of months, the AERATOR (12) may have collected debris.
To clean, remove AERATOR (12) and rinse with water and remove any debris. Turn on faucet to wash any debris
out of the faucet. Thread AERATOR (12) back into spout. Operate faucet.
Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows
and check SPOUT O-RINGS. First turn off water supply.
1
3
Remove HANDLE BUTTON (2) and loosen SET SCREW (1) with 2.5mm HEX
WRENCH (11) supplied. Pull HANDLE (3) off valve stem.
Pull off CAP (4). Loosen CARTRIDGE SCREWS (5) and remove CARTRIDGE (6).
2
4
11
Remove SPOUT (7) by pulling up gently while moving SPOUT (7) side to side.
5
Check both SPOUT O-RINGS (8) for damage. Replace if necessary.
On models with SPRAYS, DIVERTER (9) can be cleaned by pulling
DIVERTER (9) out of the MANIFOLD (10). Rinse clean the DIVERTER (9)
and MANIFOLD (10). Push DIVERTER (9) back into MANIFOLD (10).
6
13
Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
7
Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and
remove HANDLE (3).
Remove ESCUTCHEON CAP (4). Unscrew the three CARTRIDGE
SCREWS (5). Clean MANIFOLD (10), CARTRIDGE (6) ports and
SEALS (13).
12
Clean inlets of CARTRIDGE (6) and MANIFOLD (10).
SPOUT
HUB
10
8
9
Reassemble CARTRIDGE (6), alternately tightening SCREWS (5).
Replace CAP (4) and HANDLE (3). Check flow.
6
ADJUST HOT LIMIT STOP
HOT LIMIT SAFETY STOP ADJUSTMENT
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to
adjust min./max. discharge temperature. "1" being the hottest to "8" the coldest temperature setting. Factory set at "1".
"A"
"RED RING"- HOT LIMIT SAFETY STOP
ADJUSTMENT WHEN WATER IS TOO HOT
PRY RED RING UPWARD
AND ROTATE CLOCKWISE
"A"
TEMPERATURE
SETTING NUMBERS
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
PRY RED RING UPWARD
AND ROTATE
COUNTER-CLOCKWISE
7
"B"
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M965472 REV. 1.2 (12/14)
PORTSMOUTH™
SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
MODEL NUMBERS
4285.001
4285.001F15
M962994-0070A
BUTTON AND
SCREW KIT
M964398-YYY0A
HANDLE KIT
M907360-YYY0A
ESCUTCHEON CAP
M918506-0070A
CARTRIDGE SCREWS
A951470-0070A
CARTRIDGE
Replace the YYY with
Appropriate finish code
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
042850-0070A
DIVERTER
M923825-YYY0A (2.2 GPM)
AERATOR
M922881-YYY0A (1.5 GPM)
AERATOR
M907989-YYYOA
MOUNTING RING KIT
M953668-YYY0A
HANDSPRAY & HOSE
A911897-0070A
SEAL
M964065-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M953040 -YYY0A
SPRAY HOLDER
M962146-0070A
MOUNTING KIT
HOT LINE FOR HELP
M965472 REV. 1.2 (12/14)
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising