Blaupunkt Orlando DJ A Operating instructions

Blaupunkt Orlando DJ A Operating instructions
Radio / Cassette / Changer
Orlando DJ
A
Operating instructions
Orlando DJ A d®
1
13.05.2002, 11:07 Uhr
ENGLISH
23
22
21
19 18 17
20
FRANÇAIS
24
16 15
NEDERLANDS
ITALIANO
26 25
14
1
SVENSKA
13
3
4
5
6
7
8
9
10
11 12
PORTUGUÊS
ESPAÑOL
2
3
Orlando DJ A d®
3
13.05.2002, 11:07 Uhr
Switching the audio source ........ 38
Radio operation with RDS ........... 39
AF - Alternative frequency .................... 39
REG - regional programme .................. 39
Selecting a waveband .......................... 39
Station tuning ........................................ 39
Automatic tuning / ....................... 39
Manual tuning with << >> .................. 40
Scrolling through the broadcasting
networks (only FM) ............................... 40
Changing the memory bank (FM) ......... 40
Receiving traffic programme
stations with RDS-EON................ 44
Traffic announcement priority on/off .... 44
Warning beep ....................................... 44
Switching the warning beep off ......... 45
Automatic seek tuning start .................. 45
Adjusting the volume for traffic announcements and the warning beep ................ 45
Adjusting GEO for traffic messages
and the warning beep ........................... 45
CD changer control A 05 .............. 48
Switching to CDC operation ................. 48
Selecting CDs and titles ....................... 48
MIX playback ........................................ 48
Selecting the display mode .................. 48
Storing the display mode ...................... 49
SCAN operation .................................... 49
Entering CD names .............................. 49
Deleting CD names with
DSC-UPDATE ...................................... 49
DSC programming ....................... 50
Overview of the DSC factory settings .. 52
Appendix ....................................... 53
Specifications ........................................ 53
29
Orlando DJ A gb®
29
13.05.2002, 11:11 Uhr
DEUTSCH
ENGLISH
FRANÇAIS
Putting the unit into operation .............. 37
Removing the KeyCard ........................ 37
“Training” a second KeyCard/
Replacing a KeyCard ............................ 37
Displaying the radio pass data ............. 37
Short Additional Memory (S.A.M.) ........ 38
Turn On Message (T.O.M.) .................. 38
Optical indication for extra security ...... 38
Care of your KeyCard ........................... 38
ITALIANO
KeyCard theft protection
system ........................................... 37
Inserting a tape ..................................... 46
Removing a tape ................................... 46
Fast Forward/Rewind ........................... 46
Selecting titles with S-CPS ................... 46
Switching the tape side ........................ 46
Tape equalisation ................................. 46
Scanning cassette titles with SCAN ..... 47
Dolby B NR* .......................................... 47
Skipping unrecorded tape portions
with Blank Skip ..................................... 47
Listening to the radio during fast tape
winding with RM .................................... 47
Care notes ............................................ 47
NEDERLANDS
Precautions ........................................... 36
Traffic safety ......................................... 36
Installation ............................................. 36
Telephone mute .................................... 36
Accessories .......................................... 36
Tape operation ............................. 46
SVENSKA
Important notes ............................ 36
Storing stations ..................................... 40
Automatically storing the strongest stations with Travelstore ............................ 41
Recalling stored stations ...................... 41
Scanning stored stations with
Preset Scan .......................................... 41
Scanning stations with Radio-Scan ...... 41
Changing the scan time ........................ 41
Selecting the seek tuning sensitivity .... 41
Switching from stereo to mono (FM) .... 42
PTY – Programme Type ....................... 42
Switching PTY on/off ......................... 42
Programme type ................................... 42
Checking the programme type of
the station .......................................... 42
Displaying the selected programme
type .................................................... 42
Selecting a programme type ............. 42
Storing programme types .................. 43
Scanning stations with PTY-SCAN ... 43
PTY priority ........................................ 43
ESPAÑOL
Quick reference ............................ 30
PORTUGUÊS
Contents
Quick reference
1 Switching on/off with the ON button:
Press ON.
When switching the set on with the ON
button, the KeyCard has to be inserted. The unit will play with the preadjusted volume.
Switching on/off with the KeyCard:
The set has to be turned on via the ON
button.
Note:
Read the information in chapter
“KeyCard theft protection system”.
Switching on/off via the ignition:
When connected correspondingly, the
set can also be turned on and off via
the vehicle ignition.
After the ignition has been switched
off, a double beep tone will remind you
that you should remove the KeyCard
before leaving your vehicle.
Switching on with the ignition being
switched off:
To keep on operating the set when the
ignition is switched off (KeyCard is inserted), proceed as follows:
Press ON after the double beep tone.
The unit will be turned on.
To avoid that the battery goes flat, the
system will be turned off automatically
after a playback time of one hour.
2 VOL+ / VOLTo alter the volume.
Each time the set is switched on, it will
play with the pre-adjusted volume
(VOL FIX).
You may also change the VOL FIX setting (see chapter “DSC programming”).
3
For instantly muting the volume.
button the volume
By pressing the
will be muted immediately. “MUTE” will
appear in the display.
The function is cancelled by pressing
or VOL+.
button
When pressing VOL-, the normal volume will be by one grade lower than
the mute volume.
To programme the mute volume level,
proceed as follows:
• Adjust the desired volume.
for two seconds until you
• Press
hear a beep.
Now this volume level is stored as your
mute volume.
Extra function
Memory button in the DSC menu.
4 FMT
Press repeatedly to switch between
the FM memory banks I, II and T
(Travelstore).
When pressing this button, the system
will automatically switch to FM.
Extra function FMT
To store the six most powerful stations
automatically with Travelstore:
Press FMT until you hear a beep or
“T-STORE” appears in the display.
5 M•L - toggle switch
To toggle between medium and long
wave reception.
30
Orlando DJ A gb®
30
13.05.2002, 11:11 Uhr
DEUTSCH
6 Rocker switch
Radio operation
Changer operation
CD selection
Up
Fast forward
ITALIANO
Up
Down
Down
Fast rewind
Title selection
Stop function by pressing
.
Upwards: Press briefly.
CUE - fast advance (audible):
Keep depressed.
Downwards: Press as many times
as required.
To restart a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
Extra rocker switch functions:
Further setting functions with
AUD
J
GEO
I
DSC MODE H
PTY
>
Condition: The corresponding function
has to be activated.
31
Orlando DJ A gb®
31
13.05.2002, 11:11 Uhr
NEDERLANDS
Title selection (S-CPS)
SVENSKA
<</>> To scroll through the station networks when AF is on,
e.g. NDR 1, 2, 3, 4, N-JOY, FFN,
ANTENNE ... .
/
ESPAÑOL
Station search
Up
Down
<</>> Up/Down in short intervals when AF
is off
PORTUGUÊS
/
FRANÇAIS
ENGLISH
Tape operation
7 Display
f) lo
g) I, II, T
h) 6
i) LD
j)
k) AF
a
e fg h i j k l
m n
o
b
m) TA
n) PTY
o) B
p) MTL
r q p
c
l) TP
s
d
q) RM
r) BLS
s) MIX
a) NDR2
b) TR 2
- Station name
- Track (side) 2 of the cassette
c) VIVALDI - CD name or
d) 1 : 52
- CD time (playback time)
and number for changer
operation
e) FM
- Waveband
- Seek tuning sensitivity
- Memory bank I, II or
Travelstore
- Preset button (1-6)
- Loudness
- Stereo
- Alternative frequency for
RDS operation
- A traffic station is being received
- Priority for traffic stations
- Programme type function
- Dolby B noise reduction
- A metal or CrO2 type is being played
- Radio-Monitor (to listen to
the radio during fast tape
winding)
- Blank-Skip (to skip unrecorded tape portions)
- CD playback in random
order
8 KeyCard theft protection system
To operate the set it is necessary that
the KeyCard is inserted.
KeyCard
For this purpose, introduce the
KeyCard (with the contact area showing up) into the slot above the tongue
sticking out of the unit.
To remove the card, press first to unlock.
Read also the information in chapter
“KeyCard theft protection system”.
Flashing KeyCard tongue
When the radio is turned off and the
KeyCard removed, the KeyCard
tongue can be programmed to flash for
optical theft protection.
For more information see chapter
“DSC programming”.
This flashlight can be switched off by
pushing in the tongue and lock.
32
Orlando DJ A gb®
32
13.05.2002, 11:11 Uhr
Press MIX as many times until the desired function briefly appears in the
display.
: SC
Radio operation
Scan
Press SC briefly –
“FM SCAN” and the name of the
scanned station will alternately appear
in the display. The unit will scan all
stations which can be received.
CD-Scan
Press SC.
“CDC-SCAN” will appear in the display.
All CD titles will be scanned briefly.
To stop CD-Scan:
Press SC once again.
; lo
To switch the seek tuning sensitivity
level:
Press button briefly.
To switch between mono and stereo
reception:
Press button for approximately two
seconds (beep).
will disappear for
The stereo symbol
mono playback.
Regional function on/off:
Press the AF button for approximately
two seconds until you hear a beep.
“REG-ON” or “REG-OFF” will appear
in the display (see chapter REG - regional programme).
> PTY (Programme Type)
In the PTY mode, the preset buttons
become programme type buttons. With
each preset you can select one programme type, such as for example
NEWS, SPORT, POP MUSIC, EDUCATE, etc.
33
Orlando DJ A gb®
33
13.05.2002, 11:11 Uhr
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
MIX OFF
The Mix function is deactivated.
Changer operation
NEDERLANDS
MIX MAG
The CD titles will be played at random.
The individual discs are also selected
in random order.
= AF
Alternative frequency during RDS operation:
When “AF” lights up in the display, the
system will automatically seek a frequency offering better reception of the
same RDS programme.
AF on/off: Press AF briefly.
SVENSKA
MIX CD
The CD titles will be played at random.
The individual discs are selected in numeric order.
< TA (priority for traffic announcements)
When “TA” lights up in the display, the
system will play traffic stations only.
Priority on/off: Press TA.
ESPAÑOL
Changer (CDC) operation
Preset Scan
Press SC for approximately two seconds until you hear a beep.
“SCAN” and the name of the scanned
station will alternately appear in the
display. The unit will scan all stations
stored on the preset buttons.
To stop Scan / Preset Scan:
Press SC once again.
PORTUGUÊS
9 MIX
? SRC (source)
You can switch between the different
audio sources radio, tape, and CDC.
When this function has been activated,
“RM” shows on the display panel.
The radio is played back during fast
tape run.
@ DIS
D Cassette loading slot
Insert the tape with side A or 1 facing
up, the open side showing to the right.
E
B
Radio operation
Press to eject the tape.
When pressing the DIS button, the frequency will be displayed for approximately four seconds.
Tape operation
When pressing the DIS button, the station name/frequency will be displayed
for approximately four seconds.
Changer operation
To switch the display mode and select
between name, time (playback time)
and number (disc number):
• Press DIS briefly.
A RM (Radio Monitor)
Press this button to listen to the radio
while fast forwarding or rewinding the
tape.
To switch RM on/off: Press RM.
C 1, 2, 3, 4, 5, 6 - preset buttons
On FM, you can store six stations for
each of the memory banks I, II and T.
On MW/LW, you can store six stations
each.
To store a station: Press a preset
button during radio operation and hold
down until the set resumes play after
the muting and you hear a beep.
To recall a station: Select the desired
waveband. On FM, also adjust the
corresponding memory bank. Then
press the relevant preset button briefly.
Extra function preset buttons
To store and recall a PTY programme
type.
On FM, you can store and recall one
programme type on/from each preset
button when PTY is active (“PTY”
lights up in the display).
Tape side selector
Press this button to switch over to the
other side during tape operation. The
display shows “TR 1” or “TR 2”.
FB
Dolby B NR*
Press this button to play back a tape
which has been recorded with Dolby-B
noise reduction. When this button is
pressed, „B“ lights up in the display.
* Noise Reduction system manufactured under license from Dolby Laboratories Licensing Corporation. „Dolby“ and the double-D symbol are
trademarks of Dolby Laboratories Licensing Corporation.
G LD
Loudness - When listening at a low
level, the Loudness function creates a
more natural sound by boosting the
low frequency range.
LD on/off: Press the button.
When the Loudness function is active,
“LD” will light up in the display.
See chapter “DSC programming” for
more information.
34
Orlando DJ A gb®
34
13.05.2002, 11:11 Uhr
DEUTSCH
ENGLISH
J AUD
To adjust the treble and bass frequencies with the rocker switch.
NEDERLANDS
ITALIANO
I GEO
To adjust the balance (left/right) and
fader (front/rear) with the rocker
switch.
Extra function GEO
Separate balance and fader settings
for traffic messages. See chapter “Adjusting GEO for traffic messages and
the warning beep”.
FRANÇAIS
H DSC (Direct Software Control)
Use the DSC function to customise
certain programmable, basic settings
to suit your personal needs and preferences. See chapter “DSC programming” for more information.
ESPAÑOL
The last setting will be stored automatically.
To switch off GEO: Press button once
again.
If the setting remains unchanged
within four seconds, the display will
switch back to the previous condition.
The last setting will be stored automatically.
To switch off AUD: Press button once
again.
If the setting remains unchanged within four seconds, the AUD setting will
be terminated automatically.
PORTUGUÊS
Fader front
Fader rear
Balance left
Balance right
SVENSKA
Treble +
Treble –
Bass –
Bass +
35
Orlando DJ A gb®
35
13.05.2002, 11:11 Uhr
Important notes
Precautions
Installation
Accessories
Before starting to use your new car radio,
please read the following information carefully.
If you would like to install your new car stereo yourself or add other audio components
to existing ones, then please read carefully
the enclosed instructions on installation and
connection.
In order to ensure that the set operates properly it is necessary that the positive power
supply line is connected via the ignition and
the permanent +12 V lead.
Do not ground the loudspeaker outputs!
Use only the accessories and spare parts
approved by Blaupunkt.
Traffic safety
As the driver of a motor vehicle, it is your
responsibility to pay attention to the traffic
situation at all times. Never use your car
radio in a way that could distract you.
Please keep in mind that you travel a distance of 14 m per second at a speed of only
50 km/h.
Should the traffic situation become particularly demanding, we advise you not to use
the radio.
Always make sure that you are still able to
hear any warning signals coming from outside of the vehicle, such as police or fire
engine sirens, so that you can react accordingly.
Therefore, you should always select a
moderate volume for playing your car radio
while you are driving.
You can use the following Blaupunkt products with this car stereo:
Remote control
With the infrared remote control RC 05 you
can control all of the important functions of
your car hi-fi system from the steering wheel.
Telephone mute
If you have a mobile telephone installed in
your vehicle, radio, tape or changer playback can be muted automatically when using the phone (telephone mute).
“PHONE” will then appear in the display.
When TA is active, traffic messages will always have priority. The announcement will
be aborted by pressing the TA button.
Amplifier
All Blaupunkt amplifiers
36
Orlando DJ A gb®
36
13.05.2002, 11:11 Uhr
•
Turn on the set.
Introduce the KeyCard into the slot
with the contact area showing up
(KeyCard tongue sticking out).
The car radio is now ready for operation.
If a wrong KeyCard is inserted, then “CARD
Displaying the radio pass data
“Training” a second KeyCard/
Replacing a KeyCard
While operating the unit with the first
KeyCard, you can “train” a second one to
be also used with the set:
• Insert the first KeyCard and turn on the
set.
•
Using the KeyCard supplied with your set
you can have the radio pass data such as
the model name, product number (7 6 ...)
and serial number indicated on the display
panel.
Please refer to chapter “DSC programming
- READ KC”.
Press the DSC button and select
“LEARN KC” with / .
37
Orlando DJ A gb®
37
13.05.2002, 11:11 Uhr
ENGLISH
FRANÇAIS
ITALIANO
Remove the first KeyCard and insert
the new one while “CHANGE” is still
being displayed.
After the display indication “READY” or
“LEARN KC”,
• press DSC.
Now you can also use the new KeyCard for
operating your unit.
A maximum of two cards can be used for
the set.
When trying to “train” a third one, the access authorisation for the KeyCard not used
for the “training” process will be deleted
automatically.
NEDERLANDS
Never pull out the KeyCard directly!
• First, slightly push in the KeyCard.
This releases the card and puts it in the
proper position for being removed.
• Now you can pull it out.
•
SVENSKA
Removing the KeyCard
• Press << or >>.
The display will switch to “CHANGE”.
• Push in the KeyCard. The card is released and put in the proper position
for being removed.
ESPAÑOL
Putting the unit into operation
ERR” will appear in the display. In this case
please do not make any further adjustments.
The system will switch off after approximately ten seconds.
When inserting another card type (e.g.
phone or credit card), the display will show
“WRONG KC” for approximately two seconds.
Remove the wrong card and introduce the
correct KeyCard.
After the display indications “CARD ERR”
or “WRONG KC”:
• Press ON to turn on the set.
PORTUGUÊS
This car radio is supplied with one KeyCard
as standard, though it can also be operated
with a second card.
If you have lost your KeyCard or if it was
damaged, you can buy a new one from your
specialised dealer.
When using two KeyCards, the settings
stored on the first card will be adopted. However, you can individually store the following functions:
Preset button assignments, bass, treble,
balance and fader settings, Loudness, TA
(traffic announcement volume), beep volume.
In addition, the settings activated before
switching the radio off, such as the waveband, station, TA priority, AF, REG ON/OFF,
SCANTIME, seek tuning sensitivity and VOL
FIX will also remained stored.
This ensures that you will find your basic
settings re-adjusted automatically as soon
as you have inserted your KeyCard.
DEUTSCH
KeyCard theft protection system
Switching the audio source
Short Additional Memory
(S.A.M.)
Optical indication for extra
security
The second KeyCard available from your
specialised dealer offers you the possibility
to read out any short information, which will
be moved through the display, such as, for
example, the phone number of your car dealer or the emergency call number of your
automobile association. Please refer to
chapter “DSC programming - READ KC”.
The freely selectable text with a maximum
of 48 characters can be programmed by all
dealers who have the required equipment
available.
Flashing KeyCard tongue
radio,
When the vehicle is stationary and the
KeyCard removed, the KeyCard tongue can
be switched to flash for extra anti-theft security.
For this it is necessary that the positive power supply line and the permanent +12 V lead
are connected such as described in the installation instructions.
Be sure that “LED ON” is adjusted in the
DSC mode.
If required, please refer to chapter “DSC
programming - LED”.
tape,
Using the SRC button you can switch between the following audio sources:
changer.
Tape operation is only available if a cassette
is inserted.
To switch to another source,
• press SRC briefly.
Turn On Message (T.O.M.)
The second KeyCard available from your
specialised dealer also allows you to display a special turn-on message each time
the radio is switched on.
The freely selectable text with a maximum
of 48 characters can be programmed by all
dealers who have the required equipment
available.
The programmed text will be displayed each
time you turn on your system with the second KeyCard.
Switching off the flashlight
The flashlight can be switched off by pushing in the KeyCard and lock.
If you would like to deactivate the flashing
tongue with general effect, adjust the relevant item in the DSC menu to “LED OFF”.
Care of your KeyCard
For a proper function of the KeyCard it is
important that the contacts are free from any
foreign particles. Avoid direct skin contact.
If necessary, clean the KeyCard contacts
using a cotton swab soaked with alcohol.
38
Orlando DJ A gb®
38
13.05.2002, 11:11 Uhr
In order to switch this function on or off,
• press the AF button briefly.
While searching for the strongest reception
signal, the radio may switch to mute briefly.
With this car radio you can select between
the following wavebands:
FM 87.5 - 108 MHz
MW 531 - 1602 kHz
LW 153 - 279 kHz
• Select the desired waveband by pressing the FMT or M•L button.
To toggle between MW and LW:
• Press M•L.
Station tuning
Automatic tuning
39
•
Press / ; the car radio will automatically search for the next station.
When keeping the upper or lower part /
of the rocker switch depressed, seek tuning
will speed up in upwards or downwards direction.
13.05.2002, 11:11 Uhr
DEUTSCH
ENGLISH
FRANÇAIS
/
39
Orlando DJ A gb®
ITALIANO
Certain radio programmes are split up at
times into regional programmes offering local information. The 1st programme broadcast by NDR, for example, offers programmes with different contents in the
northern states of Germany SchleswigHolstein, Hamburg and Lower Saxony at
certain times of the day.
If you are listening to one programme and
move to an area where another linked regional programme becomes stronger, the
unit will switch to that programme.
If you wish to continue listening to the first
programme,
• press the AF button for approximately
two seconds.
“REG ON” appears in the display.
Selecting a waveband
SVENSKA
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected programme is always
tuned in automatically.
This function is activated when “AF” appears
in the display.
REG - regional programme
If you leave the service area of the regional
programme tuned into, or if you would like
to take advantage of the full RDS service,
switch to “REG OFF”.
• Press the AF button for approximately
two seconds until “REG OFF” appears.
“REG ON” or “REG OFF” will be briefly displayed each time the radio is switched on.
ESPAÑOL
AF - Alternative frequency
If “SEARCH” appears in the display when
switching on the radio or recalling one of the
stored frequencies, the unit is automatically
searching for an alternative frequency.
“SEARCH” will disappear from the display
when the alternative frequency has been
found or after the frequency band has been
run through completely.
If the reception quality of the selected programme becomes too bad:
• Tune into another station.
PORTUGUÊS
The Radio Data System offers you more
convenience when listening to FM radio stations.
More and more radio stations have begun
to broadcast RDS information alongside
their programmes.
As soon as a programme has been identified, the station name including a regional
identifier, if applicable, will appear in the display, for example, NDR1 NDS (regional programme in Lower Saxony, Germany).
When RDS is activated, the preset buttons
become programme buttons. You now know
exactly which programme you have tuned
into, making it easy to find the desired station quickly.
But RDS offers you further advantages:
NEDERLANDS
Radio operation with RDS (Radio Data System)
Scrolling through the broadcasting networks (only FM)
•
Press the FMT button as many times
until the desired memory bank lights
up in the display.
If necessary, deactivate these functions:
• Press AF or PTY.
You can use the << >> buttons to tune in
stations of your reception area.
If several programmes of the broadcasting
networks can be received, you can scroll
through them in forwards direction pressing
>>, or backwards using the << button, e.g.
NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE ...
For this it is necessary that the stations have
been tuned in at least once and that “AF” is
active (lights up in the display).
For this purpose, you may start Travelstore
seek operation:
• Press FMT for two seconds; the system starts to run through the frequency
band.
If “AF” does not light up,
• press AF.
With this, the requirements for selecting stations with << >> are fulfilled.
Manual tuning:
Changing the memory bank (FM) Notice:
•
You can shift between the memory banks I,
II and T in order to store stations and recall
them later.
The currently selected memory bank is indicated in the display.
Seek tuning
Up
Down
Down in short intervals
(“AF” must be switched off)
Up in short intervals
(“AF” must be switched off)
Manual tuning with << >>
You can also tune in a station manually.
Condition:
AF and PTY must be switched off (i.e. the
symbols do not light up in the display).
Press << >>; the frequency will change
in short intervals in downwards or upwards direction.
When holding the right or left part of the rocker switch depressed, the frequency scan is
speeded up.
Storing stations
On FM, you can store six stations on the
preset buttons 1-6 for each of the memory
banks I, II and T.
On MW/LW, you can store six stations each.
• Select the appropriate waveband with
FMT or M•L.
•
Tune in a station with the rocker switch
(either automatically / or manually
<< >>).
•
Press the desired preset button until
the radio resumes play after the muting (takes approximately two seconds,
confirmed by beep).
Now the station has been stored.
The activated preset button is indicated in
the display.
Should you tune in a station which has already been stored before on another
memory bank, the corresponding preset
button and the memory bank will briefly flash
in the display.
40
Orlando DJ A gb®
40
13.05.2002, 11:11 Uhr
You can recall any stored station at the touch
of a button.
• Select the waveband by pressing FMT
or M•L. On FM, also choose the corresponding memory bank by pressing
the FMT button as many times until the
desired bank appears in the display.
•
Scanning stations with RadioScan
You can also scan all stations which can be
received.
To start the Scan function:
• Press SC briefly.
The scanned frequency or the station name
will start flashing in the display. During the
actual scanning process “FM-SCAN” or
“AM-SCAN” will be displayed.
The scan time can be changed from between five to a maximum of 30 seconds.
Please refer to chapter “DSC programming
- SCANTIME”.
Selecting the seek tuning sensitivity
You can alter the automatic seek tuning
sensitivity.
If “lo” is displayed, the radio will only pick up
strong, local stations (low sensitivity).
If “lo” does not light up, the radio will also
pick up weaker, distant stations (high sensitivity).
The sensitivity level can be altered in both
modes (see also chapter “DSC programming”).
Press the corresponding preset button
briefly to recall the station.
41
Orlando DJ A gb®
41
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
To select a scanned station and switch
off Preset Scan:
• Press SC briefly.
Changing the scan time
NEDERLANDS
To start Preset Scan:
• Press SC for approximately two seconds.
All of the stored stations of the adjusted
waveband will be scanned one after the other. The memory bank and preset position of
the currently scanned station will flash in the
display.
SVENSKA
Recalling stored stations
You can have all of the stored stations briefly
scanned on all wavebands.
To select a scanned station and switch
off the Radio-Scan function:
• Press SC briefly.
If no station is selected, the scan function
will be automatically switched off after the
frequency band has been run through completely. The unit will tune in the station listened to before starting the scan.
ESPAÑOL
You can automatically store the six most
powerful FM stations of your current reception area sorted according to their signal
strength. This function is particularly convenient on longer trips.
• Press the FMT button for two seconds.
“T-STORE” will appear in the display.
The six strongest FM stations will be automatically stored on the memory bank “T”
(Travelstore). When this process has been
completed, the radio will play the first station.
If desired, stations can also be stored
manually on the Travelstore bank (see “Storing stations”).
Scanning stored stations with
Preset Scan
PORTUGUÊS
Automatically storing the
strongest stations with
Travelstore
13.05.2002, 11:11 Uhr
Switching from stereo to mono
(FM)
If reception is poor, you may get better
sound quality by switching to mono:
• Press the lo button for approximately
two seconds.
With mono playback, the stereo sign will
disappear from the display.
Each time the radio is switched on, stereo
playback is activated.
The unit will automatically switch to mono if
the received signal is not strong enough for
stereo playback.
PTY – Programme Type
PTY is an RDS service offered by more and
more radio broadcasters. This feature allows
you to select FM stations according to their
programme type. After you have chosen the
PTY of your preference, the corresponding
stations can be selected either by seek
tuning or using the scan function.
Switching PTY on/off
• Press PTY.
When the function is active, the programme
type selected last will briefly appear in the
display. “PTY” will be permanently indicated in the lower right corner of the display
panel.
Programme type
Use << >> to have the last selected programme type displayed and to choose a new
one.
You can select any one of the stored types
with the preset buttons 1 - 6.
Condition: PTY must be active.
Using DSC you can choose between German and English (see “DSC programming PTY LANG”).
All of the programme types listed below are
available.
The letters printed in bold are identical to
the actual short-time indication in the display.
NEWS
CURRENT AFFAIRS
INFORMATION
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP MUSIC
ROCK MUSIC
M.O.R. M (middle of the road music)
LIGHT M (light classical)
CLASSICS (serious classical)
OTHER M (other music)
Checking the programme type of the
station
•
Press PTY for approximately two seconds.
After the beep tone the display will show the
programme type offered by the tuned in station.
If “NO PTY” appears in the display, the current station has no PTY code.
Displaying the selected programme
type
• Press << or >>.
The programme type selected last will be
displayed briefly.
Selecting a programme type
a) Using the preset buttons
When PTY is switched on, you can use
the preset buttons 1-6 to select the
programme types stored at the factory.
• Press one of the presets 1 - 6.
The selected programme type will be
displayed for two seconds.
If you wish to listen to a station with
this PTY,
•
press /
eration.
PTY 16 to PTY 30 are not yet assigned.
42
Orlando DJ A gb®
42
13.05.2002, 11:11 Uhr
to start seek tuning op-
•
During this period press >> (forwards) or << (backwards) to select
the desired type.
Press << or >> as many times as
required.
If you wish to listen to a station offering
the selected PTY,
press / to start seek tuning operation.
If the system is unable to find a station offering the selected programme type, the display will show “NO PTY” and a beep tone
•
Select a programme type using buttons << >> and
•
hold down the desired preset button
(1-6) until you hear a beep.
Now the selected programme type can be
recalled by pressing this preset. For this the
PTY function must be active.
-
Station tuned in: NDR3.
-
“PTY” lights up in the display.
-
Programme type “POP” selected.
Scanning stations with PTY-SCAN
-
Seek tuning is started.
Condition: “PTY” must appear in the display.
-
• Press the SC button.
All received stations offering the selected
programme types will be scanned.
No station with “PTY-POP” can be
found.
-
The display shows “NO PTY” and
-
automatically switches back to NDR3.
To switch off PTY-SCAN:
• Press SC once again.
-
NDR2 airs a “PTY-POP” programme.
-
The system will switch to the linked
station NDR2 for the duration of the
“POP” programme.
43
Orlando DJ A gb®
43
13.05.2002, 11:11 Uhr
FRANÇAIS
ENGLISH
DEUTSCH
Example:
German broadcasting network NDR:
ITALIANO
•
PTY is switched on and lights up in the display.
No station offering the selected programme
type can currently be received (with seek
tuning or scan).
The set will switch back to the previous station.
As soon as a programme with such PTY can
be received within the broadcasting network,
the unit will switch over to the corresponding station for the duration of the programme.
NEDERLANDS
•
Press << or >>; the programme
type selected last will be displayed
for three seconds.
One programme type was assigned to each
of the preset buttons 1-6 at the factory.
If desired, you can also store other available programme types.
To do so, make sure that “PTY” lights up in
the display.
• If necessary, press the PTY button to
switch on the function.
Situation:
SVENSKA
•
Storing programme types
PTY priority
ESPAÑOL
b) Using the << >> buttons of the rocker
switch
When PTY is switched on, you can select a programme type using buttons
<< >>.
will be released. The station received before starting seek tuning will be tuned in.
PORTUGUÊS
If the system is unable to find a station offering the selected programme type, the display will show “NO PTY” and a beep tone
will be released. The station received before starting seek tuning will be tuned in.
You can assign different programme types
to each preset position. Please refer to the
next chapter “Storing programme types”.
Receiving traffic programme stations with RDS-EON
During tape or CDC operation, the set will
also automatically switch to the programme
offering the selected PTY within the broadcasting network.
After the PTY programme the system will
remain in the radio mode.
Notice:
As earlier mentioned, these functions are
currently only supported by a limited number
of RDS stations.
The abbreviation “EON” stands for Enhanced Other Networks, meaning the
exchange of information within a radio network.
Many FM broadcasters offer traffic messages for their service area at regular intervals.
All traffic programme stations transmit a
special carrier signal alongside their programmes, which is decoded by your car radio. If this signal is identified, “TP” will appear in the display (Traffic Programme).
In addition to these, there are also stations
which do not actually transmit traffic programmes themselves, but by using RDSEON they offer the possibility to receive the
traffic messages broadcast by another traffic programme station in the same radio
network.
If you wish to have the priority for traffic announcements activated while listening to
one of these stations (e.g. NDR3), “TA” must
appear on the display panel.
If a traffic announcement is broadcast, the
radio will automatically switch to the linked
traffic programme station (in this case,
NDR2) for the duration of the message and
return to the original programme (NDR3)
afterwards.
Traffic announcement priority
on/off
If the priority for traffic announcement programmes is activated, “TA” will light up in
the display.
To switch the priority on or off:
• Press the TA button.
When pressing TA while a message is being broadcast, this message will be interrupted. The unit will then switch back to the previous condition. The priority for other traffic
messages remains active.
Please note that several buttons have no
function while a traffic announcement is
broadcast.
Warning beep
If you leave the reception area of the traffic
programme station currently tuned into, you
will hear a warning beep after approximately 30 seconds.
This alarm tone will also be released when
pressing a preset button which has no traffic programme allocated to it.
44
Orlando DJ A gb®
44
13.05.2002, 11:11 Uhr
•
Press TA.
“TA” will disappear from the display.
Automatic seek tuning start
(tape and CD changer operation)
DEUTSCH
Adjusting GEO for traffic messages and the warning beep
You can separately adjust the balance and
fader settings for both traffic announcements
and the warning beep.
For example, it is possible to listen to traffic
reports via the front left (right) speaker only.
This provides the driver with the important
traffic information without bothering the rear
passengers too much.
To make a setting:
• During an announcement, adjust the
balance and fader settings to suit your
personal preferences.
PORTUGUÊS
When leaving the reception area of the
tuned in traffic programme station while
listening to a tape or CD, the system will
automatically start searching for a new TA
programme.
If no such station is found within approximately 30 seconds, tape or CD operation
will be stopped and a warning beep will
sound. To switch the warning beep off, proceed as described above.
ENGLISH
press a preset button which has a
traffic programme station allocated
to it.
Alternatively:
b) Switch off the priority for traffic announcements:
FRANÇAIS
•
This volume was preset at the factory,
though you can alter the value using the
DSC function (see “DSC programming, TA
VOL”).
ITALIANO
Press the rocker switch or
NEDERLANDS
•
SVENSKA
a) Tune into another station offering traffic information:
Adjusting the volume for traffic
announcements and the warning
beep
ESPAÑOL
Switching the warning beep off
45
Orlando DJ A gb®
45
13.05.2002, 11:11 Uhr
Tape operation
The car stereo has to be switched on.
Fast Forward/Rewind
portion of at least three seconds between
the individual titles.
The unit automatically switches to tape operation when a cassette is inserted.
Switching the tape side
(autoreverse)
Inserting a tape
•
Turn on the set.
• Insert a tape.
The tape will be automatically transported
to the playback position. Side A or 1 starts
to play.
During tape operation, “TR 1” or “TR 2”
(track) will show on the display panel.
Fast forward
Fast rewind
/
Title selection (S-CPS)
Stop function by pressing
Insert the tape with side A or 1 facing up, the
open side showing to the right.
Up
Down
.
Selecting titles with S-CPS
(Super Cassette Programme Search)
Use this function to skip ( ) and repeat ( )
recorded titles.
A maximum of nine titles can be skipped.
To do so,
• press the rocker switch as many times
as required.
The number of titles to be skipped appears
on the display panel.
If necessary, you can correct your entry by
pressing the opposite rocker switch button.
.
Stop by pressing
For a proper operation of the S-CPS function there has to be an unrecorded tape
Removing a tape
•
Press
.
The cassette will eject.
To change the tape direction during cassette
playback:
.
• Press
At the end of a tape side, the mechanism
changes directions automatically to play the
other side (autoreverse). The display shows
“TR1-PLAY” for track (side) 1 or “TR2-PLAY”
for track 2.
Notice:
If there is too much tension on the tape
during playback, the set may switch over by
itself before having reached the end of the
tape side. In this case check the condition
of the cassette tape. Sometimes it helps to
rewind it completely.
Tape equalisation
When a metal or CrO2 tape is inserted, the
tape mechanism automatically adjusts to
metal/CrO2 tape equalisation.
The “MTL” indicator will illuminate.
46
Orlando DJ A gb®
46
13.05.2002, 11:12 Uhr
To switch on/off:
• Press B (not during scan operation).
* Noise Reduction system manufactured under license
from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
Listening to the radio during fast
tape winding with RM
(Radio Monitor)
DEUTSCH
When the tape is fast forwarded or rewound
(also with S-CPS), the radio will normally
be muted. To listen to the radio during fast
winding, activate the Radio Monitor function.
To switch RM on and off:
• Press RM.
When the function is active, “RM” will light
up in the display.
SVENSKA
With this unit you can play back tapes recorded with Dolby-B NR or without noise
reduction.
Cassette tapes recorded with Dolby NR*
stand out by their reduced tape hiss and the
improved dynamics.
If Dolby-B NR is switched on, “B” will light
up in the display.
ESPAÑOL
Dolby B NR*
To switch the Blank Skip function on and
off:
• Press the RM button for approximately
one second until you hear a beep.
When the function has been activated, “BLS”
will appear in the display.
PORTUGUÊS
To start/stop the scan function:
• Press the SC button briefly.
You can individually adjust the scan time in
the DSC menu (see “DSC programming SCANTIME”).
To avoid possible problems, we recommend
you to use C-60/C-90 type cassette tapes
only. Store your tapes in a cool place away
from dirt, dust and temperatures exceeding
50 °Celsius. Allow very cold tapes to warm
up before playing them in order to avoid
uneven tape transport. After approximately
100 hours of use, dust particles collected
on the playback head or roller may lead to
tape run problems and sound distortions.
Use a head cleaning tape to remove normal dirt build-up. For tougher cases, use a
cotton swab (Q-Tip) soaked with alcohol. Do
not attempt to clean by inserting a hard object into the player!
47
Orlando DJ A gb®
47
ENGLISH
This function senses an unrecorded tape
portion continuing for more than 15 seconds
and automatically fast forwards the cassette
to the beginning of the next track.
During fast tape winding, “B-SKIP” will be
indicated on the display panel.
FRANÇAIS
You can have the cassette titles played briefly by using the scan function. If you like a
title, stop the scan to continue listening to
that track.
Care notes
ITALIANO
Skipping unrecorded tape portions with Blank Skip
NEDERLANDS
Scanning cassette titles with
SCAN
13.05.2002, 11:12 Uhr
CD changer control A05
Switching to CDC operation
MIX playback
Selecting the display mode
Make sure that at least one CD has been
inserted into the magazine.
You can have the CD tracks played in random order.
You can select the desired display mode for
CD operation:
Press SRC to go through the available audio sources:
• Press as many times until the display
briefly shows “CDC ON”.
MIX CD
“NAME”
– The specified name, for
example “MADONNA”
will be displayed.
“TIME”
– The elapsed playback
time of the title is displayed, for example
“2 : 32”.
Selecting CDs and titles
– The titles of the selected CD
will be played at random.
The next disc will be selected in numeric order.
MIX MAG – All CD titles will be played at
random.
The next disc will then also
be selected and played randomly, etc.
MIX OFF – The Mix function is deactivated. Discs and titles will be
selected in numeric order.
To alter the setting:
• Press MIX as many times until the desired function is briefly displayed.
If the function is active, “MIX” will appear in
the right display corner.
CD selection
Up
Down
Title selection
Upwards: Press briefly.
CUE - fast advance (audible): Keep
depressed.
“NUMBER”
– The CD position in the
magazine (disc number)
is displayed, for example
“CD8 T5”.
To switch the display mode:
• Press DIS during CD playback.
The display mode and the corresponding
setting or value will briefly show on the display panel, e.g. “TIME”, “2 : 32”.
If you have selected “NAME” without having specified a name for the corresponding
disc, “CD PLAY” will appear in the display.
Please read also the chapter “Entering CD
names”.
Downwards: Press as many times as
required.
To restart a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
48
Orlando DJ A gb®
48
13.05.2002, 11:12 Uhr
SCAN operation
Use this function to scan all of the CD tracks.
To start the Scan function:
• Press SC.
The titles will be scanned one after the other in ascending order.
To stop the Scan function:
• Press SC briefly.
The track currently being scanned is continued to be played.
SCAN will also be terminated by
• pressing one of the buttons AUD,
GEO, DSC, SRC, , << >> or / .
To start the entry:
• Press the DSC button.
“CDC-NAME” will be displayed.
• Press .
The first underscore character will flash.
• Select the first character with the help
of the rocker switch / .
You have the choice between the capital
letters A to Z, special characters and the
numbers 0 to 9.
• Use the rocker switch << >> to move
to the next underscore and select a
character.
You can select up to seven characters.
Once you have completed the name as desired:
in order to store it.
• Press
To quit the naming mode,
• leave the DSC menu by pressing DSC.
If you would like to name another CD,
• select a new disc.
You can change any existing name by entering and storing a new one (overwriting).
•
Press the DSC button.
•
Press / to select “CDC UPD”.
49
Orlando DJ A gb®
49
13.05.2002, 11:12 Uhr
ENGLISH
DEUTSCH
• Press << >>.
After the update has been completed,
“NEXT MAG” appears in the display.
• Press the button on the changer for
approximately two seconds.
The magazine will eject.
• Insert the next magazine.
Proceed as described above for all of the
CDs/magazines for which the entered name
is to be maintained.
• After having updated the last magazine, press .
To quit the function,
• press DSC.
The system has saved the name information for all of the CDs which were inserted.
For all other discs the CD names have been
deleted.
FRANÇAIS
Hold down the DIS button until you
hear a beep.
ITALIANO
•
You can delete a CD name with the help of
the DSC update function. Use “CDC UPD”
to confirm all of the CDs for which the specified name is not to be deleted.
• Insert a magazine with CDs for which
the stored information is to be maintained.
NEDERLANDS
You can name up to 99 discs.
The specified name (e.g. VIVALDI) will then
appear in the display.
Be sure to select the display mode “NAME”
using the DIS button.
SVENSKA
You can store your preferred display mode
which will then be active each time the radio is switched on.
If required,
• press DIS as many times until the desired setting is displayed.
Deleting CD names with
DSC-UPDATE
ESPAÑOL
Entering CD names
PORTUGUÊS
Storing the display mode
DSC programming
DSC (Direct Software Control) allows you
to customise certain programmable, basic
settings to suit your personal needs and
preferences and then store them.
The basic settings for this audio equipment
were made at the factory.
In the following you can find an overview of
these settings, so that you can always reset
to these if desired.
If you wish to alter any of the programming,
• press DSC.
button to
Use the rocker switch and the
select and adjust the functions described in
the following. The display will show you the
adjusted condition.
/
<< >>
Select function
Adjust/recall value
CDC NAME Only available for CD
changer playback.
Use this function to name
your CDs. (See “Entering
CD names”).
SPEECH
LOUDNESS Loudness - When listening
at a low level, the Loudness
function creates a more natural sound by boosting the
low frequency range.
LOUD 1 - Low boost
LOUD 6 - Max. boost
TA VOL
To adjust the traffic announcement and warning
beep volume from between
0 to 63.
The message will then come
through at this volume, if the
standard volume is lower.
Should the standard volume
be higher than the TA VOL
level, then the traffic report
will be played slightly louder
than the standard volume.
50
Orlando DJ A gb®
50
13.05.2002, 11:12 Uhr
In future many RDS radio
stations will differentiate between music and speech
programmes.
You can alter the tone for
speech programmes from
between “SPEECH 0 ... 4”.
SPEECH 0:
Music/speech off
SPEECH 1:
Linear reproduction (bass,
treble and Loudness set to
“0”)
SPEECH 2-4:
Different settings for volume, bass and treble with
the Loudness being
switched off.
Try out which SPEECH setting you like most.
LED ON
Here you can choose between LED ON or LED OFF.
With LED ON, the KeyCard
tongue will flash for extra
anti-theft protection when
the unit has been switched
off and the KeyCard removed.
LEARN KC
To “train” a second
KeyCard.
Please read the information
in chapter “KeyCard theft
protection system - “Training” a second KeyCard”.
DEUTSCH
To select the programme
type language:
DEUTSCH or ENGLISH
ENGLISH
PTY LANG
FRANÇAIS
You can adjust the display
brightness from between 1
to 16. You can also select
different values for day and
night.
Selecting the night brightness:
Switch on the vehicle lights
and programme the brightness value. The car radio’s
lighting connector must be
hooked up to the vehicle’s
electric system for this to
function properly.
green .............. light orange ................. red
ITALIANO
BRIGHT
To read out the KeyCard
data.
The card supplied with the
radio is used to display the
model name, type number
(7 6..) and the serial
number.
With the extra card it is possible to display the Short
Additional Memory (S.A.M.)
data entered by your specialised dealer. See chapter
“Short Additional Memory
S.A.M.”.
If you remove the KeyCard
during the reading process,
“READ KC” will show on the
display panel. The unit continues to play but does not
accept any operations except from being switched
off. Re-insert the card.
NEDERLANDS
Use this setting to alter the
viewing angle to your liking
from -1 to 0 to +1.
READ KC
PORTUGUÊS
ANGLE
COLOUR
(Variocolour) For gradually matching the
radio illumination with the
dashboard lighting.
SVENSKA
Acknowledgement tone for
all functions which require a
button to be pressed for
more than one second.
The volume can be adjusted
from between 0 to 9. (0 =
off).
ESPAÑOL
BEEP
51
Orlando DJ A gb®
51
13.05.2002, 11:12 Uhr
SCANTIME
S-DX
S-LO
Use this function to set the
scan time for the radio or
CD player from between five
and 30 seconds.
To adjust the seek tuning
sensitivity for distant reception.
DX 1 - high sensitivity
DX 3 - low sensitivity
To adjust the seek tuning
sensitivity for local reception.
LO 1 - high sensitivity
LO 3 - low sensitivity
The seek tuning sensitivity
values can be separately set
for AM and FM.
CDC UPD
VOL FIX
Use this function to delete
CD names during CDC operation, in order to have
more storage capacity for
new discs available. See
“Deleting CD names with
DSC-UPDATE”.
Use this function to select
the volume at which the radio is set when it is switched
on. Adjust the desired volume level with << >>. When
adjusted to “VOL 0”, the
system will come on with the
volume selected before
switching the radio off.
To quit the DSC programming mode
and store the adjustment:
• Press DSC.
Overview of the DSC factory
settings
CD NAME
LOUDNESS
TA VOL
SPEECH
BEEP
ANGLE
BRIGHT
COLOUR
LED
LEARN KC
READ KC
PTY LANG
SCANTIME
S - DX
S - LO
CD UPD
VOL FIX
52
Orlando DJ A gb®
52
13.05.2002, 11:12 Uhr
3
35
0
4
0
16
green
ON
ENGLISH
10 sec.
1
1
0
DEUTSCH
Appendix
Specifications
0.9 µV at 26 dB
signal-to-noise ratio
FM frequency response:
30 - 16 000 Hz
Tape player
Frequency response:
30 - 18 000 Hz
ENGLISH
-
Then call the following chargeable
phone number: 01 80 / 5 25 56 66.
-
Using the area code to be entered
you will be automatically given the
address and phone number of the
next Blaupunkt service centre. You
can also request this information
by fax.
PORTUGUÊS
ESPAÑOL
CD player
Frequency response:
5 - 20 000 Hz
Subject to modifications!
53
Orlando DJ A gb®
FRANÇAIS
If you would like to know the address of
the next Blaupunkt service centre of
your area without having our service list
at hand:
- Find out your area code.
ITALIANO
FM sensitivity:
87.5 – 108 MHz
531 – 1602 kHz
153 – 279 kHz
Address of the next service
centre in your vicinity
(only for Germany)
NEDERLANDS
Tuner
Wavebands:
FM
:
MW
:
LW
:
4 x 23 W RMS power
acc. to DIN 45324 at
14.4 V
4 x 35 W max. power
Blaupunkt
telephone hotline
SVENSKA
Amplifier
Output power:
53
13.05.2002, 11:12 Uhr
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
Blaupunkt-Werke GmbH
Bosch Gruppe
6/96 Pf
K7/VKD 8 622 400 800
29
Orlando DJ A d®
29
13.05.2002, 11:07 Uhr
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement