advertisement
XR8 WASH
XR8 WASH (Cod. 03.MW001.L)
• Electromagnetic ballast 230V 50/60 Hz • Black colour
XR8 WASH (100V) (Cod. 03.MW001.100.L)
• Electromagnetic ballast 100V 50/60 Hz • Black colour
XR8 WASH (120V) (Cod. 03.MW001.120.L)
• Electromagnetic ballast 120V 50/60 Hz • Black colour
User’s Manual Rel 1.1
GB
D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.it
Made in Italy
2
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso scritto della D.T.S.
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de ningún tipo sobre la utilización o sobre la aplicació n de los productos o de los circuitos descritos.
XR8 WASH (Cod. 03.MW001.L)
• Electromagnetic ballast 230V 50/60 Hz • Black colour
XR8 WASH (100V) (Cod. 03.MW001.100.L)
• Electromagnetic ballast 100V 50/60 Hz • Black colour
XR8 WASH (120V) (Cod. 03.MW001.120.L)
• Electromagnetic ballast 120V 50/60 Hz • Black colour
3
INDEX:
1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention
2.2 Prevention of electric shock
2.3 Protection against ultraviolet radiation
2.4 Safety
2.5 Level of protection against the penetration of solid and liquid matter
5
3- MOUNTING THE LAMP
3.1 Lamp alignment
6
4- VOLTAGE AND FREQUENCY
5- INSTALLATION
5.1 Safety cable
5.2 Protection against liquids
5.3 Movement
5.4 Risk of fire
5.5 Forced ventilation
5.6 Ambient temperature
6- MAINS CONNECTION
6.1 Protection
7- DMX SIGNAL CONNECTION
7.1 DMX Addresses
7.2 Selecting the DMX address
7
7
8
9
8- DISPLAY FUNCTIONS 11
9- PAN & TILT SPEED 14
10- FANS SPEED
11- ERROR MESSAGES
12- HIDDEN MENU 15
16 13- OPENING THE PROJECTOR HOUSING
14- PERIODIC CLEANING
14.1 Lenses and reflectors
14.2 Fans and air passages
15- PERIODIC CONTROLS
16- DMX PROTOCOLS 17
17-COLOUR WHEEL 22
18- MOTORS CONTROL CARD 23
19- PAN & TILT CARD 24
20-CABLES RESEND CARD
21-DISPLAY CARD
22- LAMP ON-OFF CONTROL CARD
4
1- TECHNICAL FEATURES
The XR8 Wash is fitted with a Philips MSR 575/2 discharge lamp
(GX9,5 lampholder base), with a colour temperature of 7,200 °K and a luminous flux of
49,000 Lumens.
Duration is 750 hours, with replacement recommended before 1000 hours
Other recommended lamps: Philips 575 MSD (6.000K°-49.000 Lumens-3.000 hours)
The unit incorporates:
Motorized zoom (20°-45°), rotating and indexable beam shaper (0°-180°), frost filter, 2 colour conversion filters (3.200°K and 5.600°K), CMY colour generation + a colour wheel (6 dichroic filters + open, with linear selection, and electronic or electromagnetic ballast.
Optical group
Fresnel lens Ø 200 mm (Borosilicate dichroic parabolic reflector)
Zoom
Motorized zoom (20°-45°)
Dimmer / shutter / strobo
Linear dimmer - Shutter - Strobe from 0,85 flash/sec to 10 flash/sec
Colours
CMY color generation system with 3 palettes for gradual and linear insertion + colour wheel (6 colours + open). Color change with blackout sync
Effects
Rotating and indexable beam shaper (0°-180°)
Colour conversion filters
3.200°K and 5.600°K
Pan / Tilt
Pan 540° (3,9 sec.) Tilt 320° (2,6 sec.) 16-bit resolution
16 DMX channels
Connections
2 XLR connectors (In and Out) with 3 and 5 pins selectable by user
Power supply
Electromagnetic ballast: 230 V 50-60 Hz (Standard)
On request: 100 V 50-60 Hz /120 V 60 HZ
Power consumption 750 W
Remote Lamp on/off via DMX
Operating ambient temperature -10° / 40°
Weight
29 Kg (XR8 Wash Electromagnetic ballast: 230 V 50-60 Hz)
Packing Dimensions
(HxWxL)
800 x 440 x 550 mm
Weight
36 Kg
5
XR8 WASH
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention:
XR8 uses a Philips 575 MSR/2 or MSD
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
-Minimum distance from the closest illuminable surface: 2 MT.
-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
2.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head, including lamp replacement.
-The level of technology present in the XR8 requires the assistance of specialised personnel for all servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
2.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
2.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
2.5 Level of protection against the penetration of solid and liquid matter:
-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid matter is IP 20.
6
XR8 WASH
3- MOUNTING THE LAMPS
Warning: Switch off the unit before replacing the lamp.
Philips 575 MSR/2
Power 575W
Luminous flux 49,000 lm
Colour temperature 7.200°K
Lampbase GX9,5
Rated life 1,000 hours
Philips 575 MSD
Power 575W
Luminous flux 43,000 lm
Colour temperature 6.000°K
Lampbase GX9,5
Rated life 3,000 hours
1) Using a screwdriver, remove the 3 screws A,B, C, (photo 1) which fix the lamp holder.
Photo 1 Photo 2 Photo 3 Photo 4
2) Remove the lamp holder assembly (photo2).
3)Insert the lamp (photo 3).
The lamp used on XR8 is made in quartz glass and should be handled with care. Always follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided in the lamp's packaging. The GX9,5 lamp socket is symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat the procedure.
4) Replace the lamp assembly and tighten the screws A,B,C, which were previously removed (photo4).
3.1 Lamp alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic filters and other components inside the unit.
Photo 5
Alignment is carried out using the 3 adjusters X, Y and Z.
During this operation you must have a uniform luminosity all around the projected area.
7
XR8 WASH
4- VOLTAGE AND FREQUENCY
The XR8 with electromagnetic ballast can operate at 230 V 50-60 Hz (Standard)
On request: 100 V 50-60 Hz /120 V 60 HZ
5- INSTALLATION
XR8 may be either floor or ceiling mounted.
For floor mounting installations, the XR8 is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to move or shake whilst the XR8 is moving.
Four quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps
.
provided in the box, to fix the unit in any position.
5.1- Safety cable
We recommend the use of a safety cable or chain connected to the XR8 and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the picture below.
A
5.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.
8
5.3- Movement
The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any obstructions in the path of the projector's movement.
270°
XR8 WASH
540°
5.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 2 MT.
5.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
5.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.
6- MAINS CONNECTION
XR8 with electromagnetic ballast operate at 230 VOLT 50-60 Hz
(On request: 100 V 50-60 Hz /120 V 60 HZ
Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 6,3 amps at 208-230V,
Or 12 amps at 100-120 V
Strict adherence to regulatory norms is strongly recommended.
6.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each XR8.
A good earth connection is essential for the correct operation of the projector.
Electromagnetic ballast
230 V 50/60 Hz (standard)
On request: 100 V 50-60 Hz
120 V 60 HZ
7- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a
CANNON XLR 5 or 3 pins connector.
9
XR8 WASH
Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
5
4
CONTROLLER
S T A N D A R D
DM X 5 1 2
1
2
1=GND
2=DATA-
3=DATA+
3
For Installations where long distance DMX cable connections are needed,we suggest to use a DMX terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
5
4
3
2
1
OUT
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
120 ohm
PIN 3
PIN 2
10
7.1-DMX Addresses
XR8 Wash have 16 DMX channels.
Set the following addresses on the mixer:
Projector 1 A001
Projector 2 A017
Projector 3 A033
…..
A….
projector 6 A081
If you want to select the next projector, just add “16”
XR8 WASH
7.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.
11
XR8 WASH
8- DISPLAY FUNCTIONS
MAINS
Electronic ballast
90-245V 50 / 60Hz
Electromagnetic ballast
230 V 50/60 Hz (standard)
On request: 100 V 50-60 Hz
120 V 60 HZ / 208 V 60 Hz
DISPLAY
DMX IN
DMX OUT
MENU
ENTER
UP
DOWN
DISPLAY FUNCTIONS
The XR8 display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
MENU Up-Down
PAN MOVEMENT INVERSION
To reverse Pan movement from left to right and vice versa
ENTER Up-Down
Up-Down
MENU Up-Down
TILT MOVEMENT INVERSION
To reverse Tilt movement from bottom upwards and vice versa
ENTER Up-Down
Up-Down
MENU Up-Down ENTER
REVERSE DISPLAY
Reverses display's reading depending on the mounting position
(On the ground or suspended).
Up-Down
Up-Down
DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.
MENU Up-Down
DMX MODE
To select DMX mode :
Mode 1 or Mode 2
ENTER Up-Down
Up-Down
Clockwise
ENTER
Counterclockwise
ENTER
Clockwise
ENTER
Counterclockwise
ENTER
ENTER Up-Down
ENTER Up-Down
Floor position
Suspension
position
ENTER
ENTER
Display OFF
ENTER
Display always ON
ENTER
DEFAULT
SAME FIXTURE AS
XR 7 WASH
16 CHANNELS
(Pan & Tilt 16 bit)
16 CHANNELS
(Pan & Tilt 16 bit)
ENTER
ENTER
12
XR8 WASH
8- DISPLAY FUNCTIONS
MENU Up-Down
TEST MODE
Full test and single function test.
ENTER Up-Down
ALL
PAN
TILT
DIMMER
SHUTTER
COLOR
CYAN
ENTER Up-Down
MENU Up-Down
RESET
Al motors reset
ENTER
MAGENTA
YELLOW
EFFECTS
ZOOM
RESET ENABLED VIA DMX
RESET DISABLED VIA DMX
TOTAL RESET
ENTER
ENTER
ENTER
ENTER MENU Up-Down
DEFAULT
To restore default setting
MENU Up-Down
SOFTWARE
Software version
MENU Up-Down
Fan control
To control the fan speed .
MENU Up-Down
SPEED control
Pan Tilt Speed control.
ENTER
Pcb 8 motors. Pcb PAN&TILT
ENTER Up-Down
ENTER Up-Down
ENTER
ENTER
(DEFAULT : 12 )
ENTER
ENTER
(DEFAULT : 2 )
13
XR8 WASH
8- DISPLAY FUNCTIONS
MENU Up-Down
LAMP
Lamp always ON-always OFF
Or lamp ON-OFF selectable via DMX
ENTER Up-Down
ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and ZOOM
ON / OFF VIA DMX (default)
ENTER
ENTER
FORCED ON
ENTER
FORCED OFF
ENTER Up-Down ENTER Up-Down
STR
Lamp strikes counter
ENTER
Up-Down
MENU Up-Down
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
ENTER
PAN LOCK
LOCK THE PAN TO THE DESIRED VALUE
TILT LOCK
LOCK THE TILT TO THE DESIRED VALUE
PAN FREE
REMOVE POWER TO PAN MOTOR
TILT FREE
REMOVE POWER TO TILT MOTOR
MENU Up-Down ENTER Up-Down
TIMER lamp life TIME (reset possible) and total UNIT LIFE TIME (reset not possible)
Up-Down
Up-Down
.
.
.
.
ENTER Up-Down
ENTER Up-Down
ENTER Up-Down
ENTER Up-Down
ENTER
ENTER
ENTER
ENTER
ENTER Up-Down
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER Up-Down
ENTER
ENTER Up-Down
14
XR8 WASH
9- PAN & TILT SPEED (SPEE) (default: 2)
You can set the PAN and TILT motors at high speed on your XR8.
Press menu until you see SPEE.
Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.
When you use speed 4 (the highest) PAN and TILT speed is very high and your projector may loose its path. In this case, the encoder corrects the position.
10- FAN SPEED (FANS)( default: 12)
Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be less than 35° C.
11- ERROR MESSAGES:
ERROR POSITIONING
OF COLOUR WHEEL
ERROR POSITIONING
OF BEAM SHAPE EFFECTS
ERROR POSITIONING
OF ZOOM
ERROR ALIGNMENT
SENSORS OF ZOOM LENS
ERROR INPUT
IN AUTO MODE
ERROR INTERNAL
COMMUNICATION
ERROR SYNCHRONIZED
FREQUENCY MEASURE
(SYNCHRONISM FOR LAMP ON)
ERROR ENCODER PAN
ERROR ENCODER TILT
ERROR DMX ADDRESS
ERROR LOADING
EPROM DATA
ERROR COLOUR SENSOR
CIRCUIT/ZOOM 1
ERROR COLOUR SENSOR
CIRCUIT/ZOOM 2
15
XR8 WASH
12- HIDDEN MENU
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
Reset the XR8 (reset from the MENU, not from the DMX controller!).
While reset is running, press the MENU and ENTER keys at the same time.
Electronic calibration of the motors.
Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must repeat all previous calibrations)
Exit from hidden menu.
ENTER Up-Down
PAN ALIGNMENT
To align pan movement
Up-Down
TILT ALIGNMENT
To align tilt movement
Up-Down
SHUTTER ALIGNMENT
To align shutter
Up-Down colour WHEEL ALIGNMENT
To align colour wheel
Up-Down
EFFECT ALIGNMENT
Effect alignement
Up-Down
ZOOM 1 ALIGNMENT
To align zoom1
Up-Down
ZOOM 2 ALIGNMENT
To align zoom 2
Up-Down
CYAN ALIGNMENT
To align cyan colour
Up-Down
MAGENTA ALIGNMENT
To align magenta colour
Up-Down
YELLOW ALIGNMENT
To align yellow colour
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
Up-Down
ES.
Up-Down
ES.
Up-Down
ES.
Up-Down
ES.
Up-Down
ES.
Up-Down
ES.
Up-Down
ES.
Up-Down
ES.
16
Up-Down
ES.
Up-Down
ES.
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
16
XR8 WASH
13- OPENING THE PROJECTOR HOUSING
It is possible to inspect the inside of the projector by removing the cover as indicated below.
ATTENTION
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .
2) Once unscrewed, simply lift the covers to access the internal components (photo 2).
Photo 1 Photo 2
14- PERIODIC CLEANING
14.1- Lenses and reflectors
Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
14.2- Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.
15- PERIODIC CONTROLS
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will help to avoid the danger of the lamp exploding.
Mechanical parts
Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S. distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors; refasten them if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XR8.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.
17
XR8 WASH
16- DMX PROTOCOL
16 CHANNEL MODE ( 16bit)
1
2
3
4
5
PAN ms b ( 5 4 0°)
PAN lsb
TILT msb(320°)
MOVEMENT SPEED
6 D MER
7
8 C OUR
9 C
10 MAGENTA
11 YEL L O
12 SPEED CMY / DIMMER
13 MACRO CMY / COLOUR
15 ZOOM
16 RESET
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX CHANNEL
DMX range
Value
0-10
11-25
26-127
128-247
1
Parameter:
2
Parameter:
3 Parameter:
4 Parameter:
5 Parameter:
PAN msb 540°
PAN lsb
TILT msb 319°
TILT lsb
MOVEMENT SPEED
Mid point
DMX value
Move range
(degrees)
Mode Option
248-255
DMX CHANNEL 6
Parameter: DIMMER
Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Slow reaction time to DMX signal
DMX range
Value
0-8
9-255
Mid point
DMX value
Move range
(degrees)
Mode Option Function
Black-out
Proportional dimmer
0-12
13-25
26-38
39-51
52-64
65-77
78-90
91-103
104-116
117-129
130-142
143-155
156-168
169-181
182-197
198-200
201-203
204-206
207-209
DMX CHANNEL
DMX range
Value
0-9
10-23
24-37
38-51
52-65
66-79
80-93
94-107
108-121
122-135
136-149
150-163
164-177
178-191
192-205
206-219
220-227
228-233
234-255
DMX CHANNEL
7
Parameter: SHUTTER
Mid point
DMX value
Move range
(degrees)
Mode
8
Parameter: COLOUR
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode
18
Option Function
Black-out
Strobe random speed
Strobe speed 1 min.
Strobe speed 2
Strobe speed 3
Strobe speed 4
Strobe speed 5
Strobe speed 6 max.
Flash open speed 1 min.
Flash open speed 2
Flash open speed 3
Flash open speed 4 max.
Flash closed speed 1 min.
Flash closed speed 2
Flash closed speed 3
Flash closed speed 4 max.
Colours / Macros in black-out
Pan / Tilt in black-out
Open
Option Function
White
Colour 1 (3200° K)
Colour 2 (5600°K)
Colour 3
BiColour 3/4
Colour 4
BiColour 4/5
Colour 5
BiColour 5/6
Colour 6
BiColour 6/7
Colour 7
Bicolour 7/8
Colour 8
Bicolour 8/white
Right rotation speed 1 max.
Right rotation speed 2
Right rotation speed 3
Right rotation speed 4
-
-
19
210-212
213-215
216-218
219-221
222-224
225-228
229-231
232-234
235-237
238-240
241-243
244-246
247-249
250-252
253-255
DMX CHANNEL 9 Parameter: CYAN
DMX range
Value
0-255
Mid point
DMX value
Move range
(degrees)
DMX CHANNEL
Mode
10
Parameter: MAGENTA
DMX range
Value
0-255
Mid point
DMX value
Move range
(degrees)
DMX CHANNEL
Mode
11
Parameter: YELLOW
Option
Option
Right rotation speed 5
Right rotation speed 6
Right rotation speed 7
Right rotation speed 8
Right rotation speed 9 min
Stop
Left rotation speed 1 min.
Left rotation speed 2
Left rotation speed 3
Left rotation speed 4
Left rotation speed 5
Left rotation speed 6
Left rotation speed 7
Left rotation speed 8
Left rotation speed 9 max.
Function
Proportional colour
Function
Proportional colour
DMX range
Value
0-255
DMX CHANNEL
Mid point
DMX value
Move range
(degrees)
12
Parameter:
Mode Option
SPEED CMY / DIMMER
DMX range
Value
0-7
8-255
Mid point
DMX value
Move range
(degrees)
Mode Option
Function
Proportional colour
Function
No Function
Variable speed from max to min
-
20
85-89
90-94
95-99
100-104
105-109
110-114
115-121
122-128
129-135
136-142
143-149
150-156
157-163
164-170
171-177
178-184
DMX range
Value
0-9
10-14
15-19
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60-64
65-69
70-74
75-79
80-84
185-191
192-198
199-205
206-212
213-219
220-226
227-233
234-240
241-247
247-255
DMX CHANNEL 13
Parameter: MACRO CMY / COLOUR
Mid point
DMX value
Move range
(degrees)
Mode Option Function
No Function
Macro 1
Macro 2
Macro 3
Macro 21
Macros rainbow wait = 3
Macros rainbow wait = 4
Macros rainbow wait = 7
Macros rainbow wait = 8
Macros rainbow wait = 9
Macros rainbow wait = 10
Full colours rainbow wait = 0
Full colours rainbow wait = 2
Full colours rainbow wait = 3
Full colours rainbow wait = 4
Full colours rainbow wait = 5
Full colours rainbow wait = 6
Full colours rainbow wait = 7
Full colours rainbow wait = 8
Full colours rainbow wait = 9
Full colours rainbow wait = 10
-
DMX CHANNEL 14 Parameter: EFFECTS
DMX range
Value
0-19
20-39
40-255
Mid point
DMX value
Move range
(degrees)
Mode
DMX CHANNEL 15
Parameter: ZOOM
DMX range
Value
0-225
DMX CHANNEL
Mid point
DMX value
Move range
(degrees)
16 Parameter:
Mode
LAMP / RESET
MODE 1 (DEFAULT)
DMX range
Value
0-9
10-60
61-129
130-179
180-200
201-239
240-255
Mid point
DMX value
5
30
95
154
190
220
247
Move range
(degrees)
Mode
MODE 2 (SAME AS XR 7 WASH)
DMX range
Value
0-29
Mid point
DMX value
Move range
(degrees)
30-85
86 - 170
171-235
236-255
Mode
21
Option
Option
Function
No effect
Frost
Beam Shape
Function
Proportional
Option Function
No Effect
Lamp OFF (Active after 3 seconds)
No Effect
Lamp ON (Active after 3 seconds)
No Effect
Internal Motors Reset
Total Reset
Option Function
No effect
Lamp OFF (active after 3 seconds)
Internal motor Reset
Total Reset
Lamp ON (active after 3 seconds)
-
17- COLOUR WHEEL
2
1
COL1
3
22
4
5
8
COL2
7
COL3
6
COL4
-
0507K004
CONV.FILTER CTO
TC3256
COL5
0507K003
CONV. FILTER CTB
DL542
COL6
0507C046.D01
WOOD SW 460
COL7
0507C051.D01
ORANGE LW590
COL8
0507C042.D01
GREEN WB5055
0507C047.D01
RED LW 640
0507C041.D01
DARK BLUE SW490
0507C053.D01
AMBER LW 550
23
18- MOTORS CONTROL CARD
8 MOTORS CONTROL CARD
J7 Magnetic Sensors
Connector
Line 1 Brown:
Line 2 Orange:
GND
ORANGE
BROWN
VCC
J1 Internal DATA
Communication
Connector
From J8 Pan & Tilt card
30 VDC
+
-
Fans
XR8 WASH
Zoom motor1
(BLACK)
Zoom motor2
(DARK GREEN)
Strobe
(YELLOW)
Colour wheel
(PINK)
Effects
(GREY)
Magenta
(LIGHT BLUE)
Cyan
(GOLD)
Yellow
(BLUE)
Fans
19-PAN & TILT CARD
24
PAN
(WHITE)
TILT
(BROWN)
GND
(BLACK)
30 VDC
(RED)
FAN
(WHITE)
ENCODER PAN
(RED)
ENCODER TILT
(ORANGE)
IN LAMP
OUT LAMP
TCN0060
CN7
TO CN5 CN6
LAMP
ON-OFF
CARD
TO J1
DISPLAY CARD
(WHITE)
TO J1
8 MOTORS CARD
(VIOLET)
DMX INPUT
(WHITE)
20-CABLES RESEND CARD
21-DISPLAY CARD
BLACK RED BLACK BLACK
22-LAMP ON-OFF CONTROL CARD
If the PCB card doesn’ t work, move the cable
“IN LAMP” from CN 1 to CN 7
To remove error from display, in
Menu select
FROM J12
PAN&TILT
CARD
˜
NOTES
25
NOTES
26
NOTES
27
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S..D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.
MADE IN ITALY
*0517I066*
0517I066
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111 [email protected] www.dts-lighting.it
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project