Belling | Gas hobs | Service manual | Belling Gas hobs Service manual

1
BELLING GAS B/I HOBS
SERVICE MANUAL
2
INDEX
PRODUCT IDENTIFICATION
PAGE
APPLIANCE RATING PLATE .............................................................
3
USER GUIDE AND INSTALLATION HANDBOOK
USER GUIDE..........................................................................................
INSTALLATION INSTRUCTIONS.......................................................
TECHNICAL DATA...............................................................................
PARTS LIST GHU60GC.......................................................................
PARTS LIST GHU70C..........................................................................
WIRING DIAGRAM GHU60GC...........................................................
WIRING DIADRAM GHU70GC...........................................................
REPAIR AND MAINTAINANCE
4-12
13-21
22-22
24-24
25-25
26-26
27-27
DISASSEMBLY PROCEDURES..........................................................
COMPONANT REMOVAL..................................................................
FAULTFINDING GUIDES...................................................................
28-30
31-33
93-95
THIS MANUAL COVERS THE FOLLOWING MODELS :BELLING GHU60GC AU
BELLING GHU70GC AU
3
PRODUCT IDENTIFICATION
Appliance rating plate location
The appliance rating plate is located on the right-hand side of the
front frame and also on the rear service panel
9
10
YEAR
4
1
8
MONTH
4
4
3
2
8
NUMBER OF PRODUCTION
FOR THE MONTH
4
4
4
0
0
2
8
PRODUCT IDENTIFICATION CODE
It is important that during all service calls the model and serial
numbers are recorded on all paper work.
Users Guide
& Installation
Handbook
Belling
Built in Gas Hobs GHU60-70 AU
OUR WARRANTY
Should you need it . . . .
Inside the paperwork which has come with this appliance, there is a leaflet and card
explaining the terms of our extended warranty and guarantee. In order to apply for our
five year guarantee, simply fill in the details on the card and post it off, this will register
your appliance.
Should you wish to take out extended warranty, please fill in the details on the leaflet
and post this off to:
Glen Dimplex Australia
Unit 2, 205 Abbotts Road
Dandenong South
Victoria 3175
Australia
Ph: 1300 556 816
Fx: 1800 058 900
Glen Dimplex New Zealand Pty
38 Harris Road, East Tamaki
Auckland
New Zealand
Ph: 09 274 8265
Fx: 09 274 8472
If your appliance is covered by the warranty and guarantee, you will not be billed for
work undertaken should your appliance be faulty, terms and conditions do apply, so
please read through the literature carefully.
Please ensure that you have available your appliances model number and serial
number, there is a space at the back of this book for recording that information.
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety and Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using your hob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas & Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Please keep this handbook for future reference, or for anyone else
who may use the appliance.
Introduction
Your 1st Year Guarantee
Thank you fo r buyi ng thi s Brit ish built
appliance from Belling, this look is
intended to assist you with the
installing and use of your hob and we
recommend that your read it fully
before installation and use.
To fulfil the conditions of your guarantee, this appliance must be correctly
installed and operated, in accordance
with these instructions, and only be
used for normal domestic purposes.
Please note that the guarantee, and
Service a vailability, onl y apply to the
UK and Republic of Ireland.
We hope that the following information will help you to quickly familiarise
yourself with the features of the following appliance, an d use it successfully
and safely.
Our policy is one of constant development and improvement. Strict accuracy of i llustrations and specifications is
not guaranteed. Modification to
design and materials m aybe necessary subsequent to publication.
This hob is i ntended to be built into a
domestic kitchen, caravan or boat
intended for use on inland waterways.
This p roduct is de signed as a n a ppliance for the preparation and cooking
of domestic food products, and should
not be used for any other purpose.
This appliance must be installed in
accordance with the regulations in
force, and only in a well ventilated
space. Read the instructions before
using or installing this appliance.
Be safe - not sorry
Caution: This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room heating
WARNING! -Accesible parts may become
hot during use. To avoid burns, young
children should be kept away from the
applianceChildren should be supervised to
ensure that they do not play with the
appliance.This appliance is not intended for
use by persons (including children with
reduced physical, sensory or mental
capabilities,or lack of experience and
knowledge) unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
WARNING:- Servicing should be carried
out by authorised personnel
•
Never us e the appliance for heating
a room.
•
Turn pan handles to a safe posi-tion,
so they are out of reach of chil-dren, not
overhanging the appliance, and cannot
be caught accidentally.
•
Position pans over the centre of the
burners / hotplates. If po sitioned
off centre, smaller pans maybe unstable.
•
Keep all flammable materials (such as
curtains, clothing & furnishings) away
from the hob.
•
Do not let pans overhang the control k nobs, as th is ma y overheat
and damage them.
•
Never leave fat or oil unattended on
a lit hob.
WARNING:- This appliances is unsuitable
for use in a marine enviroment.
Do not spray aerosols in the vicinity of this
appliance while it is in operation.
Do not store or use flammable liquids or
items in the vicinity of this appliance.
Do not modify this appliance.
Auto ignition (if fitted):Push in and hold
down the controlknob, and turn to the full
on position(large fl ame s ymbol).
Keep th e knob depressed af ter the burner
has lit for up to 15 seconds to allow the flame
to establish. Turn the control knob to the
desired setting.
Manual ignition (if fitted):
Push in & hold down the control knob
turning to th e f ull on p osition ( large
flame symbol) & press the ignition button until the gas l ights. Keep the control kn ob d epressed after the burner
has l it for up to 15 seco nds to a llow
the flame to establish. Turn the control
knob to the desired setting.
In the event of the burner flames being
accidentally extinguished, tu rn off the
burner con trol and do not a ttempt to
re-ignite the burner for at least 1
minute.
Reduced rate
Turn the control knob to the small
flame symbol.
To switch off
To switch off a hob burner, turn the
control knob clockwise to the “off”
position.
If the ignition fails
1.Make sure all the controls are in the
“off” position, and check there is a
spark a t th e back of t he burner when
you depress the co ntrol knob or press
the ignition button.
2.Gas check - c heck there is gas to the
appliance by lighting a burner with a
lighted match.
3.Electrical check- if no spark renew
the 3 ampfuse in the fused spur.
4.Check burner caps are fitted correctly
Using the hob
Adjust the burner flame so that it does
not extend over the pan base.
Do not use griddle plates on this
appliance, as this may be hazardous.
Material and size of pan, as well as
quantity and type of food to be
cooked, can affect cooking times.
Commercial simmering aids should
not be used as they create excessive
temperatures that c an damage the
surface and may cause a hazard.
Pans
Use pans with a flat base of minimum 120mm / 4 ins diameter and
maximum 250mm / 10 ins d iameter which are stable in use.
Do not use double pans, rim based
pans, o ld mis shapen pans o r any
pan which is unstable when placed
on a flat surface.
Position pans over the centre of the
burners, resting on the pan supports. If positioned off centre, smaller pans may be unstable.
Do not let pans overhang the con trol knobs, as this may overheat and
damage them.
Always use pa ns whi ch a re larg e
enough to pre vent spillage, especially for deep frying.
Turn pan handles to a safe position,
so they are out of reach of children,
not overhanging the appliance, and
cannot be caught accidentally.
Pan supports
Note
Always make sure the pan supports
are replaced correctly , located in the
hob spil lage w ell, and that all ru bber
feet are in place , to prevent instability.
Extra care should be taken when cooking food in salted water. Some foods
are corrosive - eg; vinegar, fruit juices
and especially salt - they can mark or
damage stainless s teel if they a re left
on the surface. Turn off and wipe any
spillage immediately, taking care to
avoid skin contact with any hot surface
or spillage.
The hob must only be operated when
both pan supports are correctl y positioned.
To save gas
•
Always position pans central ly
over the burner.
•
Use the size of p an most suited to
the si ze o f the burner - ie ; la rger
pans on the rear burners, s maller
pans on the front burners.
•
Adjust the flames so tha t they d o
not lick up the sides of the pan.
•
Put lids on saucepans and only
heat the amount of liquid you
need.
•
When liquids boil, reduce the control setting to maintain a simmer.
•
Consider the use of a pressure
cooker fo r the cooking o f a complete meal.
•
Potatoes and veget ables will cook
quicker if chopped into saller
pieces.
Care & Cleaning
Caution: Any cleaning agent
used incorrectly may damage
the hob.
Always let the hob cool before
cleaning.
Some cooki ng operations generate a
considerable amount of grease. This,
combined with spillage, can become a
hazard if allowed to accumulate on
the hob thro ugh lack of cleaning. In
extreme cases this may amount to misuse of the appliance & could invalidate your guarantee.
Do not use caus tic, corrosive o r abrasive cleaning products, coarse wire
wool or any hard implements, as they
will damage the surfaces.
All parts of the hob can be safely
cleaned with a cloth wrung out in hot
soapy water.
Burner caps and heads
Important: Allow burners to cool
before cleaning.
Caution: Hotplate burners can be
damaged by soaking, automatic dishwashers (or dishwasher powders / liquids), caustic pastes, hard implements,
coarse wire w ool, and abrasive cleaning pastes.
Clean with a moist soapy pad.
For the burners to work safely, the slots
in the burner h ead w here the flames
burn need to be kep t clear of deposit.
Clean with a nylon brush, rinse, & dry
thoroughly.
Any brownish coloured marks o n the
burners are carbon deposits or fat stains,
which can be r emoved by gently rubbing with a soapy pad.
Important: The berner caps and
heads must be repositioned correctly
so that they sit squarely onto the hob
as shown below.
This is particularly important with stainless s teel models a s f ailure to reposition the caps correctly may result in
discolouration of the stainless steel
around the burners.
burner cap
correct
parallel
burner head
incorrect
angled
burner cap not central
incorrect
Control knobs
Only use hot soapy water.
When cleaning the f ascia are a, ca re
must be taken on symbols / markings.
Control knobs can be removed for
cleaning, but take car e to ensure that
they are repositioned correctly after
cleaning.
Vitreous enamel surfaces
HOB SPILLAGE WELL
(enamel hobs) ,
Sharp objects can mark the surface of
stainless s teel, b ut m arks wi ll b ecome
less noticeable with time.
To maintain the finish of stainless steel,
or to remove any greasy marks, wipe
the stainless steel surface sparingly
with a minimum amount of Baby O il
and kitchen paper. Do not use cooking oils, as these may contain salt,
which c an damage the stainless steel
surface.
PAN
(if fitted)
Use a mild cream cleaner .
Please note: Do not steam clean any
parts of the hob.
Stainless Steel hob
Cast iron pansupports (if fitted)
Only use a clean cloth wrung o ut in
hot soapy water, and dry w ith a s oft
cloth.
After cooking allow the pansupports to cool completely
before attempting to remove or
clean.
SUPPORTS
Stubborn marks can be removed using
“Luneta”. We recommend that you
clean the whole of th e s tainless steel
area to maintain a uniform finish.
Supplies can be purchased from the
Customer Care Centre.
Do not use undiluted bleach or any
products containing chlorides as they
can permanently damage the steel.
Extra care should be taken when cooking food in salted water. Some foods
are corrosive - eg; vinegar, fruit juices
and especially salt - they can mark or
damage stai nless s teel if the y a re l eft
on the surface. Turn off and wipe any
spillage imme diately, taki ng care to
avoid skin contact with any hot surface
or spillage.
Before cleaning, remove any excess
fat with kitchen paper.
The pan supports can be cleaned with
hot soapy water and a nylon brush. If
any food residue is left on them leave
them to soak for a few minutes in hot
soapy water before attempting to
clean it. Do n ot use caustic pastes,
abrasive cleaning powders, coarse
wire wool or any hard implements, as
they will damage the surface.
Do not clean in a dishwasher.
INSTALLATION INSTRUCTIONS - GAS PRODUCTS
Before you start: Please read the
instructions. Planning your installation will
save you time and effort.
Prior to installation, ensure that the local
distribution conditions (nature of the gas
and gas pressure) and the adjustment
of the appliance are compatible. The
adjustment conditions are stated on the
data badge.
This appliance is not connected to a
combustion evacuation device. It shall be
installed and connected in accordance
with current installation regulation.
Particular attention shall be given to
the relevant requirements regarding
ventilation.
The information below is crucial to
installing this appliance correctly and
safely.
Gas Safety (Installation & Use)
Regulations
This appliance must by an authorised
person in accordance with the
Australian Gas Installation Standard
AS5601 the manufacturers installation
instructions, local gas fitting
regulations, and any other relevant
statutory regulations.
Particular attention should be given
to relevant requirements regarding
ventilation.
Failure to install appliances correctly is
dangerous and could lead to prosecution.
Ventilation Requirements
Ventilation must be as specified by
AS 5601 Installation code. The room
conatining the appliance should have an
air supply.
An appliance should be installed in a
location for complete combustion of gas,
proper flueing and to maintain ambient
temperature of the immediate surrounding
at safe limits, under normal conditions.
Failure to install appliances correctly is
dangerous and could lead to prosecution.
WARNING - This appliance is unsuitable for
use in a marine environment.
If the appliance is placed on a base,
measures have to be taken to prevent it
slipping from the base.
Caution: The use of gas cooking appliance
results in the production of heat, moisure
and products of combustion in the room
in which it was installed. Ensure that
the kitchen is well ventilated especially
when the appliance is in use: keep
natural ventilation holes open or install a
mechanical ventilation device (mechanical
extractor hood).
Installation
Failure to comply with these
Regulations is a criminal
offence.
This appliance must be installed in
accordance with the regulations in
force, and only i n a well ventilated
space. Read the instructions before
using or installing this appliance.
Where reg ulations or standards h ave
been revised since this handbook was
printed, always use the latest edition.
This appliance will be factory set fo r
use on either natural gas only, or LPG
only. If the appliance requires conversion from natural gas to LPG, then the
conversion kit, part number 0130145
00, can be ordered from the Customer
Care Centre helpline given at the back
of this book.
All gas installati on, servicing and
repair work must be in accordance
with local standards and regulations.
Regulations & Standards
Prior to installation, ensure that the local
distribution condition (nature of the gas
and gas pre ssure) and ad justment of
the appliance are compatible.
The a djustment conditions for this
appliance are stated on the data
badge.
This appliance is not connected to a
combustion products evacuation device.
It shall be installed and connected in
accordance with current installation
regulations. Particular attention shall
be given to th e relevant requirements
regarding ventilation.
The appl iance must b e i nstalled, co nverted to LPG ( where necessary) and
serviced by a competent person to
ensure that the installation is in accordanc e with "The Gas Safety
(Installation & Use) Regulations”, & the
“The Gas Safe ty (In stallation & U se)
(Amendment) Regulations ”.
-
Clearances & dimensions
The room should have good light and
ventilation but be free from draughts.
The worktop should be at least
600mm deep, & 30mm thick to
enable the cutout to be made to the
dimensions shown below.
A m inimum distance o f 40mm s hould
be maintained between the hob a nd
rear wall / combustible surface.
A m inimum distance o f 78mm s hould
be maintained between the hob and
any side walls / combustible surface.
Surfaces which are non-combustible, or
are protected with suitable non-combustible material, may have reduced
clearances. R efer to New World f or
guidance.
We recommend ceramic tiling for the
rear wall directly behind the hob.
No shelf or overhang of combustible
material should be closer than 650mm
above the hob.
Extractor or cooker hoods should only
be fitted above the hob in accordance
with the manufacturer’s instructions.
No com bustible materials o r flammable liquids should be stored below the
hob.
Sufficient length of cable should be
allowed so the hob can be removed
for servicing, but make sure it is routed
away from the underside of the hob &
does not get trapped during installation.
Important: Ensure that you route all
electrical cables and flexible tubing
well clear of any adjacent heat source
- eg; oven / grill.
rear wall
53mm min
side wall
600 - 53mm min
700 - 103mm min
555mm
485
mm
cutout
600 hob - 600mm
700 hob - 700mm
wall unit
420
mm
worktop
wall unit
40mm
This area must
be kept clear
of combustible
materials
40mm
650mm
above level of
pan supports
Important Information
It is important when installing front
control gas hobs, that the work top
cut out is the same as is quoted in
this installation manual. If the cut out
is too large, then batons must be fitted to the front, rear and sides - to
correct the discrepancy and ensure
the correct fit. Please ensure that if
batons are fitted they are level with
the top surface of the work top
Please ensure that the seal for the
hob has full contact with the work
top surface.
Failure to follow these instructions can
lead to exessive force being applied
to the basetray, which results in the
clearence between the control knob
and the hob top pressing being
reduced. This can effect the operation of the gas control, and the ignition.
There are two ways to install
the clamps, depending on the thickness of the work top, please measure
the thickness of your work top and
ensure that the correct method is
used. Both methods are detailed in
the installation manual.
Base Tray
GDHA specified dimensions with batons
Existing dimension without batons
Fit the hob into the cutout &
secure to worktop
Place the hob into the cutout and
secure in place using the four brackets
and screws provided.
The brackets should be orientated to
suit the worktop thickness as shown,
then inserted into the four slots (two on
the front edge and two on the rear)
and screwed into the underside of the
worktop using the woodscrews provided.
40mm
worktop
seal
seal
30mm
worktop
hob
hob
The screws should be tightened just
sufficiently to secu re the hob a nd pull
the top press ing fl ush with the worktop.
If the base of the hob is accessible
after ins tallation then a partition must
be fitted 20mm below the base to prevent access.
Alternative clamp positions
If the front and rear clamp positions
are problematic, alternative positions
can be used o n the s ides of the hob,
dependant on the particular installation.
These positions will r equire clearance
from any cabinet sides and may effect
how tightly the hob will meet the worktop.
Stone (Granite or equivalent)
worktops
Depending on the type of worktop
being used, there may or may not be
any backing material to screw the
clamp screws into.
1. If the w orktop is a composite ty pe
(backed with MDF or similar) there
may b e enough backing to screw
directly i nto. This will depend on
the worktop thickness and backing
thickness and will have to be
assessed at th e installation. In this
case, install th e h ob as for a standard worktop.
2. If there is insufficient backing material to screw into, or if the worktop
is comple tely solid in const ruction,
then it will be necessary to glue a
strip of wood, MDF, fibre board or
similar to the underside of the worktop, along the front and rear edges
of the cutout. Use a strong, proprietary adhesive to bond these strips
and a llow to cure before atte mpting to clamp the hob into po sition.
Installation advice - cabinetry
Dealing with sides, cross- rails
and back-panels in cabinetry
Depending on the cabinets, the wor ktop thickness and the hob positioning,
it is possible for the hob base, the
clamp brackets and/or the gas con nection to interfere with parts of the
cabinet. These ca n b e dealt w ith a s
follows:
Cabinet sides
If the hob i s to be i nstalled across the
top of two cabinet housing units, then
the base of the hob may interfere with
the sides of these units. It will be necessary to cu t away the top of the unit
sides locally to clear the ho b, cl amp
brackets and/or gas connection.
Cross-Rails
1. Interference with hob base
If there are any cross-rails which
obstruct the hob base by running
across the worktop cutout, they can
simply be removed or locally cutaway to allow the hob to be
installed, depending on the particular installation. Any modifications
must ensure that the strength of the
cabinet is maintained.
2. Interference with clamp brackets
If the re are any cross-rails which
prevent the clamps from being
positioned on the front or rear
edges of the hob, then they can be
removed or locally cut-away
around the brackets to allow the
brackets to be installed.
Any modifications must ensure that
the strength of the cabinet is maintained.
Back-panel
1. Interference with clamp brackets
If the cabinet has a back-panel
which prevents the clamps from
being positioned on the rear edge
of the hob, then this panel can be
completely rem oved or locally cutaway to a llow the brackets to be
installed.
2. Interference or restriction of gas
connection
If the cabinet has a back-panel
which interferes with the position
of the gas supply to t he hob, then
the panel can be completely
removed or locally cut-away to
allow connection to the gas supply.
INSTALLATION INSTRUCTIONS - GAS PRODUCTS
Connect to the gas supply
Means of isolation shall be provided at the
shut off point by either an approved quick
connect device or a Type 1 manual shut
off valve. The outlet of the quick connect
device shall be at, or below, the horizontal
position.
After installation, make sure all connections
are gas sound.
Commissioning
Burner aeration
All burners have fixed aeration and no
adjustment is possible.
Pressure setting
Natural Gas @ 1.00kPa
Propane Gas @ 2.75kPa
Pressure test point
Use a hob injector.
Connection to the gas supply should be
made using the Aquaknect AS/NZS 1869
class B hose assembly with an internal
diameter of not less than 10mm and
regulator (regulator for use with natural
gas)
NOTE: Maximum length of hose 900mm.
The temperature rise of the areas at the
rear of the cooker that are likely to come
into contact with the flexible hose do not
exceed 70˙C.
The inlet to the cooker is ½” BSP internal
situated at the rear right corner. Fit the
bayonet connection. This should be
located so as to ensure that the flexible
connector hose does not kink.
Under no circumstances should the flexible
connector be allowed to come into contact with
the vertical oven flue tubes on the rear of the
appliance.
Use a 900mm - 1125mm length of
flexible connector.
Ensure that all pipework is of the correct
rating for both size and temperature.
Connect to the electricity supply
Unless this appliance is supplied with a fitted plug,
it must be connected by a competent person, using
fixed wiring via a double pole switched fused spur outlet,
with a contact separation of 3mm at all poles.
Connect the mains lead wires to the terminals:
The blue wire must be connected to the terminal marked
N(Neutral) LOAD or coloured black.
The brown wire must be connected to the terminal marked
L(Live) LOAD or coloured red.
The green/yellow coloured wire must be connected to the
terminal marked E(Earth) or coloured green.
Warning: this appliance must be earthed.
The fused spur must be accessible after installation.
If the supply cord is damaged, obtain a special cord from
the Customer Care Helpline, which must be fitted by
a qualified person.
Hob burner - Turn the control knob to the
FULL ON position, wait a second before
pressing the ignition switch or holding a
lighted match or taper to the burner. Hold
the control knob in for 15 seconds. Do not
hold the control knob in for longer that 15
seconds. If the burner fails to light within
this time, release the control knob and
wait one minute before attempting further
ignition.
Troubleshooting
Before you call Customer Care, please
check the following points:
Burner fails to ignite:
• Check the electricity supply is on.
• Check the fuse.
There is a spark t o t he bu rner
but it fails to ignite:
• Check that the flame ho les i n the
•
flame spreader are cl ear of water
or deposits.
Check that the gas supply is turned
on.
Smell of gas:
• Check that none of the controls
have inadvertently been turned
on. If all the controls are in the off
position, turn off the gas supply &
call Customer Care.
The burner flame appears
uneven:
• Check the burner is fitted correctly.
• Check the flame holes in the flame
spreader are clear of water or
deposits.
Technical Data This in formation is
for the following appliances:
Belling Hobs GHU60/70 front & side
control - NG & LPG
Data badge Underside of the hob
base
Gas pressure settings
Natural gas @ 1.0kPa
Propane gas @ 2.75kPa
Countries of destination
(AUS & NZ)
Electrical supply
240V ~ 50Hz 1W
Ignition
Mains repetitive ignition.
Gas connectionThe inlet connection
is at the rear right-hand side ISO7 - Rp1/2” (1/2” BSP)
Burner
GHU 60
Back LH
Back RH
Front LH
Front RH
GHU 70
Back LH
Back RH
Wok
Front LH
Front RH
Total Heat Input
GHU 60
GHU 70
Natural Gas
MJ/h
Injector
MJ/h
6.50
6.50
10.20
3.20
118
118
142
82
6.50
6.50
9.50
3.20
70
70
87
50
6.50
10.20
12.60
6.50
3.20
118
142
138-72
118
82
6.50
9.50
12.60
6.50
3.20
70
87
87-35
70
50
26.4
39.0
25.70
38.30
LP Gas
Injector
CONTACT US
Calling for a service
If you should experience any problems with your cooker please contact your retailer or
place of purchase.
Important note:
Service work is to be conducted by authorised persons only. It is also adviseable
that your cooker is checked regularly and maintained in good condition. An annual
maintenance is recommended.
Always check the instruction book before calling a service agent to make sure you have
not missed anything.
Glen Dimplex Australia Pty Ltd Customer Care:
Tel: Australia 1-300-556-816
New Zealand 09-274-8265
Before you contact a service agent, make sure that you have the following information to
hand:
Model Number
Serial Number
Date of Purchase
Postcode
Glen Dimplex Australia, Unit 2, 205 Abbotts Road, Dandenong,
South Victoria 3175, Australia
e-mail: sales@glendimplex.com.au
web: www.glendimplex.com.au
Model Names: Belling GHU 60 - 70 GAS HOB 08 27521 00a
05.2010
PRODUCT:
COLOUR:
CODE:
ISSUE:
DATE:
Key
0083
0084
0085
0102
0103
0104
0178
0281
0388
0580
05837
0601
0734
0736
0878
0887
0888
0889
0909
0910
0090
0091
0092
0463
0525
0614
0424
*PROV BEL GHU60GC AU Mk2 Sta
Stainless Steel
444440564
Product
073103866
082519304
082519406
082519506
082957700
082957701
082957702
082520000
082532600
082995300
082938800
082422600
502998300
083019300
081423974
082997400
082997306
082997305
082997304
082938701
082938700
073105064
082957803
082957804
082957805
702460216
083000904
082466000
073107727
082752100
Product Description
HOB MECH hob 60g be au
BURNERBOWL aux (injector 0.82)
BURNERBOWL s/rapid (inj 1.18)
BURNERBOWL rapid (inj 1.42)
BURNERSKIRT aux (serie 3)
BURNERSKIRT semi (serie 3)
BURNERSKIRT rapid (serie 3)
CLIP spring Defendi
ELECTRODE 600mm DEL701
GENERATOR ignition DG723G34+0
NUT flanged locking
SUPPORT burner
PANEL base hob 60 gas
SEAL A196-10:1
SEAL tap 4mm COPRECI F3862-04
SWITCH assembly
TAP hotplate rapid 0.45bp
TAP hotplate semi .32bp 52-54A
TAP hotplate aux 0.32bp 52-54A
Thermocouple 500mm long
Thermocouple 300mm short
HOB AES hob be ghu60gc sta
BURNERCAP aux(serie3) blk matt
BURNERCAP semi(serie3)blk matt
BURNERCAP rap (serie3)blk matt
HOTPLATE 60 hob gas be sta/blk
KNOB control bi-hob Blk/Chr
PANSUPPORT cast hob 60 fc
LABELS be hob 60g au
HANDBOOK be hob 60g au
Hob
TCO
Replace
Date
Qty
1
1
2
1
1
2
1
4
4
1
4
4
1
1
4
1
1
2
1
2
2
1
1
2
1
1
4
2
1
1
PRODUCT:
COLOUR:
CODE:
ISSUE:
DATE:
Key
0424
0083
0084
0085
0086
0102
0103
0104
0105
0178
0279
0281
0388
0580
05837
0601
0734
0736
0878
0887
0888
0889
0890
0906
0909
0910
0090
0091
0092
0094
0096
0472
0525
0615
*PROV BEL GHU70GC AU Mk2 Blk
Black
444440565
Product
073107727
082752100
073103867
082519304
082519406
082519506
082546709
082957700
082957701
082957702
082546801
082520000
082547100
082532600
082995301
082938800
082422600
502998301
083019300
081423974
082820800
082997306
082997305
082997304
082997307
082965800
082938701
082938700
073105073
082957803
082957804
082957805
082546901
082547001
712384724
083000904
082466100
Product Description
LABELS be hob 60g au
HANDBOOK be hob 60g au
HOB MECH hob 70g be be au
BURNERBOWL aux (injector 0.82)
BURNERBOWL s/rapid (inj 1.18)
BURNERBOWL rapid (inj 1.42)
BURNERBOWL wok 1.38
BURNERSKIRT aux (serie 3)
BURNERSKIRT semi (serie 3)
BURNERSKIRT rapid (serie 3)
BURNERSKIRT wok
CLIP spring Defendi
ELECTRODE wok 900mm long lead
ELECTRODE 600mm DEL701
GENERATOR ignition DG736G34+0
NUT flanged locking
SUPPORT burner
PANEL base hob 70 gas
SEAL A196-10:1
SEAL tap 4mm COPRECI F3862-04
SWITCH assy
TAP hotplate rapid 0.45bp
TAP hotplate semi .32bp 52-54A
TAP hotplate aux 0.32bp 52-54A
TAP wok 0.80bp 116-127
thermocouple wok
Thermocouple 500mm long
Thermocouple 300mm short
HOB AES hob be ghu70gc blk
BURNERCAP aux(serie3) blk matt
BURNERCAP semi(serie3)blk matt
BURNERCAP rap (serie3)blk matt
BURNERCAP wok inner-matt
BURNERCAP wok outer-matt
HOTPLATE 70 gas be
blk/whi
KNOB control bi-hob Blk/Chr
PANSUPPORT cast hob 70 fc
Hob
TCO
Replace
Date
Qty
1
1
1
1
2
1
1
1
2
1
1
5
1
4
1
4
4
1
1
5
1
1
2
1
1
1
2
2
1
1
2
1
1
1
1
5
2
BELLING GHU60GC MK2
ISSUE 1
MAINS CABLE
Wiring colour code: Bk = Black, Bn = Brown, Bu = Blue, Gn = Green, Or = Orange, R = Red, W = White, Y = Yellow
Gn
Re-ignition
Connections
Base Tray
Earth Point
IGNITION
GENERATOR
D3010: P/N DG723
20/01/2010
BELLING GHU70GC MK2
ISSUE 1
MAINS CABLE
Wiring colour code: Bk = Black, Bn = Brown, Bu = Blue, Gn = Green, Or = Orange, R = Red, W = White, Y = Yellow
Gn
Re-ignition
Connections
Gn
Base Tray
Earth Point
WOK
IGNITION
GENERATOR
D3010: P/N DG736
20/01/2010
BELLING
GAS BUILT IN
COOKTOPS
REPAIR
AND
MAINTAINANCE
PROCEDURES
2
IMPORTANT
BEFORE CARRYING
OUT ANY SERVICING
WORK ALWAYS
DISCONNECT FROM
THE ELECTRICAL
SUPPLY
3
1) REMOVAL OF COOKTOP COMPLETE
THE COOKTOP CAN BE REMOVED FROM THE WORKTOP BY:1)
2)
DISCONNECTING THE GAS SUPPLY
REMOVING THE 4 X BRACKETS FROM UNDERNEATH THE
COOKTOP
2) HOTPLATE REMOVAL
REMOVE ALL THE BURNER SKIRTS AND CONTROL KNOBS
REMOVE ALL SECURING SCREWS
FITTED AROUNG THE BURNERBOWLS (11 IN TOTAL)
REMOVE THE 2 X T10 TORX SCREWS
THAT HOLDS THE GAS RAIL
LIFT AWAY THE HOTPLATE
4
COMPONANT REMOVAL
SEMI-RAPID 6.5MJ/H
WOK BURNER 12.60 MJ/H
RAPID 10.2 MJ/H
SEMI-RAPID
6.5MJ/H
SMALL 3.20 MJ/H
GAS TAPS
IGN GENERATOR
MICROSWITCHES
A) ELECTRODES
SQUEEZE TOGETHER THE ELECTRODE CLIP AND REMOVE
LIFT THE ELECTRODE AWAY FROM
THE BURNERBOWL AND
DISCONNECT FROM THE IGNITION
GENERATOR
5
B) THERMOCOUPLES
REMOVE THE HOTPLATE AS IN STEP 2
REMOVE THE 7mm SECURING NUT
AND REMOVE THE THERMOCOUPLE
FROM THE BURNERBOWL
DISCONNECT FROM THE GAS TTAP
AND REMOVE THE THERMOCOUPLE
C) MICROSWITCHES
REMOVE THE HOTPLATE AS IN STEP 2
GENTLY EASE THE MICROSWITH OFF
THE GAS TAP
DISCONNECT FROM THE IGNITION
GENERATOR
NB THE INDIVIDUAL MICROSWITCHES CANNOT BE EXCHANGED
THEY MUST BE EXCHANGED AS A COMPLETE SET
6
D) GAS TAPS
FOLLOW STEP AND REMOVE THE
COOKTOP FROM THE WORKSURFACE
REMOVE THE HOTPLATE
DISCONNECT THE BUNDY TUBE
FROM THE GAS TAP
REMOVE THE 2 X SECURING SCREWS
AND REMOVE THE GAS TAP
NB WHEN FITTING NEW GAS TAPS ALWAYS REPLACE THE
SEALING WASHER
E) IGNITION GENERATOR
FOLLOW STEPS 1 AND 2 AND REMOVE THE COOKTOP AND HOTPLATE
EASE THE CLIP FROM THE BASE AND
REMOVE THE GENERATOR
DISCONNECT ALL WIRING AND
ELECTRODE LEADS
THE BURNERBOWLS CAN BE REMOVED BY DISCONNECTING THE GAS
BUNDY TUBE TO THE BURNERBOWL THEN REMOVING THE SECURING
SCREW ON THE UNDERSIDE OF THE COOKTOP
7
BELLING
GAS BUILT-IN HOBS
FAULTFINDING
GUIDES
Gas hob with thermocouples
Hob burner will not stay lit
Burner won’t stay on when
control knob released
Is the customer keeping the control
knob depressed for 10 secs.
NO
YES
Advise customer control knob
must be kept depressed for at
least 10 secs
Ask customer is the
thermocouple probe is in the
flame
YES
Then send engineer, order
thermocouple and gas tap.
NO
Ask customer to clean burner
skirt and cap also to make sure
they are correctly fitted.
Faulty ignition (Push button ignition)
Customer states no ignition to burner/s
Is more than one
burner affected?
NO
Are all four
burners affected
YES
Has customer check
electric supply to
hob?
NO
NO
Send engineer order
electrodes required and
possibly a spark generator
YES
Send engineer and
order ignition switch
and spark generator
YES
Can customer see a
spark at the burner?
YES
NO
Send engineer and
order electrode
Ask customer to clean
and make sure burner
skirt and cap are fitted
correctly. Did this
work?.
Faulty ignition (Automatic ignition)
Customer states no ignition to burner/s
Is more than one
burner affected?
NO
Can customer see a
spark at the burner?
YES
Are all four
burners affected
YES
YES
NO
NO
NO
Has customer check
electric supply to
hob?
Send engineer order
electrodes required and
Ignition switch (micro switch)
Ask customer to clean
and make sure burner
skirt and cap are fitted
correctly. If this does
not work.
YES
Send engineer and
order spark
generator
Send engineer order
electrode and ignition
switch ( micro switch)
Gas Hob
Faulty ignition (Automatic ignition)
Customer states no ignition to burner/s
Is more than one
burner affected?
NO
Can customer see a
spark at the burner?
YES
Are all four
burners affected
YES
YES
NO
NO
NO
Has customer check
electric supply to
hob?
Send engineer order
electrodes required and
Ignition switch (micro switch)
Ask customer to clean
and make sure burner
skirt and cap are fitted
correctly. If this does
not work.
YES
Send engineer and
order spark
generator
Send engineer order
electrode and ignition
switch ( micro switch)
Download PDF