Casablanca | Silhouette II | Owner`s manual | Casablanca Silhouette II Owner`s manual

SERRA™
SERRA™ Owner’s Manual
READ AND SAVE THESE INSTRUCTIONS!
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper
installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and
carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box
before attempting any installation procedure.
CONTENTS
INTRODUCTION
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safe Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MOUNTING RECOMMENDATIONS
General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sloped Ceiling Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FAN INSTALLATION
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Crossbar Mounting Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Lag Screw Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Canopy Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Blade Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fan Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hanging the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Canopy Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Canopy Hatch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Light Fixture Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
VERSA•TOUCH2™ CONTROL INSTALLATION
Control Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Changing Transmitter Frequency Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TROUBLESHOOTING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CARE RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
AUTHORIZED SERVICE CENTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
P3M64M AT1206
1
INTRODUCTION
BEFORE YOU START
• CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code,
ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician.
To avoid overheating and possible damage to other equipment, do not install control to a receptacle, fluorescent light
fixture, motor operated appliance, or transformer-supplied appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations. If it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 2.85 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is about 1.85 amps or 220 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
• WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades or cleaning the fan. Do
not insert foreign objects in between the rotating fan blades.
• WARNING: to reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device. Use only
the control provided with or recommended for this fan.
Unpacking
Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts
listed in the Parts Guide. Before discarding packaging materials, be certain that all parts have been removed.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
• The blades in each pack are matched for equal weight to
assure smooth fan operation. If more than one fan is being
installed, be careful not to mix blades from different
cartons.
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
Fuse Box
(Remove fuse for the
circuit you will be
working on)
• Inspect the contents of your carton for possible shipping
or handling damage. If parts are missing or damaged, call
1-888-227-2178.
• It is always a good idea to have an assistant to help with
the installation.
• When cleaning, painting, or working near your fan, be
very careful of the fan and blades. Always turn the power
OFF to the ceiling fan before working on it or replacing
lightbulbs.
• Never insert anything into the path of the fan blades while
the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in any way.
Contact Casablanca Fan Company by calling
1-888-227-2178, or contact your local authorized
Casablanca dealer for assistance in obtaining service.
2
18" ↑
70"↑
↑
84" ↑
SERRA™
MOUNTING RECOMMENDATIONS
GENERAL GUIDELINES
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
support
brace
Ceiling fans have practical uses in almost every room in your home. We suggest
you follow these mounting recommendations as you decide where to install
your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7' above the floor.
standard
mounting
style
• Do not locate the fan in a doorway or above a swinging door.
ceiling outlet
box
• In bedrooms, fans work best when mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid damage
from pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy the finish and
warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms, two fans may
be needed.
SLOPED CEILING INSTALLATIONS
SUGGESTED EXTENSION POLE LENGTHS
Ceiling Height
8' 0"
8' 6"
9' 0"
9' 6"
10' 0"
11' 0"
12' 0"
13' 0"
14' 0"
Pole Length
Extension
Pole
standard
standard
6"
12"
12"
18"
24"
36"
48"
Maximum
Hang-Tru®
angle 32º
Blades must be a
minimum of 7 feet
above the floor
7' minimum
When to Use Extension Poles
For optimum performance and appearance, an extension
pole should be used with your Casablanca fan when
installing on high (cathedral) ceilings or sloped ceilings.
Casablanca offers standard poles in increments of 6" up
to 5'. Custom poles are available in lengths up to 9'9". See
your Authorized Casablanca Dealer for details.
EXAMPLE 1
NOTE: Fan may wobble or vibrate if pole length is not
long enough and inside blade is too close to downslope or
side wall. Extending pole length will usually solve problem.
EXAMPLE 2
Calculation of Ceiling Angle
Use the tear-off Ceiling Angle Template card inserted in
this manual. It provides you with a simple “go” or “no-go”
for installing your fan on a sloped ceiling.
EXAMPLE 3
This slope is less than 32º.
It is OK to install your fan.
This slope is 32º. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your fan.
This slope is more than 32º. Your fan will not
hang straight down, an adaptor is necessary.
Contact your local Authorized Casablanca
Dealer in regards to purchasing a “Sloped
Ceiling Adaptor.”
3
FAN INSTALLATION
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
Using Existing Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you
wish to place your Casablanca fan, an approved ceiling
fixture outlet box must be installed and wired.
After turning the power OFF at its source (either the circuit
breaker or fuse box), lower the old fixture and disconnect
the wiring. Check the ceiling fixture outlet box to be sure
it is marked “Approved for Ceiling Fan Mounting.” If it is
not, a new box must be installed.
WARNING!
To reduce the risk of fire, electrical shock, or
personal injury, mount to outlet box marked
“Acceptable Fan Support of 22.7 kg (50 lbs.) or
less” using the mounting hardware provided with
the outlet box.
Note: The weight of this fan is 36 pounds.
CROSSBAR MOUNTING BRACKET INSTALLATION
CEILING HARDWARE (not to scale)
Crossbar Mounting Bracket
Screw Pack A:
Lag Screw and Washer (1)
1" x 8-32 Roundhead Screw and Washer (2)
Note: After removing the old fixture, check the outlet
box to insure that it is supported by a joist or beam across
its upper surface. If not, a 2 x4 stud must be installed.
Step 1a. Remove the knockout plug in the center of the
outlet box or drill a 1/2-inch hole for the lag screw to pass
through. Then drill a 1/4-inch guide hole into the joist or
beam to a depth of 3 inches.
Step 1b. Route the outlet box wires through the keyhole
slot of the crossbar mounting bracket as shown. Attach
the crossbar mounting bracket to the outlet box with the
screws provided in Pack A, making sure the outlet box
wires are not pinched by the washer.
Joist
Ceiling-FanApproved
Wiring Box
Crossbar Mounting
Bracket
Green Ground Wire
CAUTION:
To reduce the risk of personal injury, use only
the mounting hardware provided with the
approved outlet box to install the crossbar
mounting bracket.
WARNING!
Support directly to building structure only.
4
Wire Nut (4)
1" x 8-32
Roundhead Screw
Ceiling Wiring
Ridge side down
Washer
SERRA™
LAG SCREW INSTALLATION
NOTE: This step is required only under two conditions:
If the fan weighs 36 lbs. or more (which does not pertain
to this fan) or if the existing ceiling fixture outlet box needs
to be modified for a ceiling fan application (for example,
if the house is not new construction and you are replacing
an existing light fixture). We recommend that the ceiling
box be of sufficient capacity to support the weight of the
fan and light fixture under any conditions. If in doubt
whether you need to install the lag screw, consult a qualified
electrician.
Step 2. With the large washer attached, pass the lag screw
(Pack A) through the center hole of the crossbar mounting
bracket and screw into the guide hole. Tighten until the
outlet box is mounted firmly to the beam. This box must
be secured to the ceiling firmly.
CANOPY INSTALLATION
CANOPY HARDWARE (not to scale)
Canopy Hatch
Canopy
Pack B:
Canopy Screws and Washers (5)
Step 3. Attach the canopy to the crossbar mounting bracket
with three of the 8-32 x 21/2" long canopy screws (Screw
Pack B) and lock washers provided with your Casablanca
fan. Tighten using the provided screwdriver until snug
against the ceiling.
NOTE: On sloped ceilings, align the canopy opening
with the top or peak of the room.
Feed outlet box
wires through
canopy opening
Canopy
Lock Washer
Canopy Screw
5
BLADE INSTALLATION
BLADE HARDWARE (not to scale)
Blades (5)
Blade Badges (5)
Attach Blade Irons
Step 4. Attach blade to bladeholder by first pressing the
blade badge into the blade, then installing the bladeholder
using four blade screws provided in Pack C. Using the
provided screwdriver, tighten securely by hand only.
Repeat for each blade assembly.
Blade Installation
Step 5a. Remove the blade access plate and screws as
shown. Do not discard the two screws. They will be used
to reinstall the plate later.
Step 5b. Attach the blade/bladeholder assembly to the
motor by using two bladeholder screws from Pack D for
each blade. Use the opening created by removing the blade
access plate to align the holes in the bladeholder with the
holes in the motor. Install the screws one by one using
the provided screwdriver. Tighten securely by hand only.
Repeat for each blade/bladeholder assembly.
Step 5c Re-install the access plate.
TIP: For balancing purposes, loosely install all five blades
to the motor before tightening the blade screws securely.
CAUTION:
Blade screws must be tightened securely before
operating the fan.
6
Blade Holders (5)
Screw Pack C:
Blade Screws(21)
Screw Pack D:
Blade Iron Screws (11)
SERRA™
FAN PREPARATION
PERMA•LOCK™ HARDWARE (not to scale)
3" Perma•Lock™ Downrod
and Ball Assembly
Allen Wrench
Uplight Lightbulbs
S-11 25-watts (4)
Uplight Glass Shade
IMPORTANT SAFETY INFORMATION:
Before starting the installation of your ceiling fan,
install the threaded downrod into the motor
coupling and lock the assembly.
Perma•Lock™ Downrod
and Ball Assembly
Prepare for fan installation as follows:
Step 6a. Remove the paper shield from the motor.
Step 6b. Using the provided Allen wrench (attached to
the paper motor warning shield), loosen the Allen set
screw.
Step 6c. Route the wires through the 3" Perma•Lock
downrod and ball assembly. Insert the downrod into the
motor coupling and turn it clockwise until it stops turning,
ensuring that the pole has bottomed out.
Ground Wire
(green)
Motor Wires
(leave at least 6" long)
Allen Wrench
Tapered Thread
Motor
Coupling
Allen
Set Screw
Motor Housing
Assembly
TIP: The downrod has a tapered thread that is designed
to lock completely when installed correctly.
Step 6d. Tighten the set screw with the Allen wrench to
ensure safe operation of your fan. If it is tight enough, you
should not be able to turn the downrod counterclockwise
with your hands. If in doubt, tighten the set screw with
the Allen wrench until you cannot turn it any further.
Paper Shield
CAUTION: Failure to fully lock in the downrod
before securely tightening the Allen set screw may
cause the fan to separate from the downrod and
fall during normal operation.
Uplight Glass
Shade
Install Uplight Glass Shade and Lightbulbs
Step 7a. Fit the uplight glass shade over the motor assembly
as shown.
Step 7b. Screw four 25-watt incandescent lightbulbs into
the sockets on the motor housing.
Uplight
Lightbulbs S-11
25-watts (4)
NOTE: When replacing lightbulbs, be sure to use only
25-watt maximum.
7
HANGING THE FAN
Step 8a. To hang the fan body in the canopy, hold the fan
body firmly and insert the ball into the canopy opening.
Check that no wires are pinched. Rotate the fan body until
the slot in the ball fits into the pin opposite the canopy
opening.
Ball
Step 8b. Trim excess motor wires, leaving at least 6 inches
above the downrod. Strip 1/2-inch insulation from the end
of each wire using a wire stripper (available at your local
hardware store). The splices after being made should be
turned upward and pushed carefully into the outlet box.
Slot
CANOPY ELECTRICAL CONNECTIONS
Step 9. Attach the fan wires to the ceiling fixture outlet
box wiring by placing the bare ends of the wires side by
side and then securing with a wire nut. Test that the
connection is secure by pulling on the wire nut. Connect
in this order:
• GREEN leads from mounting plate and downrod
assembly of fan to GROUND conductor of power
source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in
ceiling fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to BLACK power wire
in ceiling outlet box. Secure with wire nut.
After making the wire connections, the wires should be
spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet
box and the ungrounded conductor on the other side of the
outlet box.
Wire Nut
2 Black
Wires
2 White
Wires
3 Green
Wires
NOTE: If the color of your ceiling wires differs from that
described, consult an electrician.
CANOPY HATCH INSTALLATION
Step 10a. Tuck the wires into the canopy with the wire
nuts pointed upwards, so that the WHITE and BLACK
wires are on opposite sides of the canopy and all wires are
clear of the canopy opening.
Step 10b. Install the canopy hatch with the last canopy
screw and lock washer using the provided screwdriver. To
do this, tilt the fan body away from the hatch opening.
Tighten the screws firmly.
Step 10c. Straighten the fan, then check to ensure
that there is no movement between the canopy and
the ceiling or the Perma•Lock™ downrod and the
ball assembly.
8
Pin
SERRA™
LIGHT FIXTURE INSTALLATION
SWITCH HOUSING HARDWARE (not to scale)
Light Assembly
Screw Pack E:
Light Assembly Screws (3)
60-watt B-10 bulbs
(Candelabra-base)
Glass Shade
Light Assembly Installation
Step 11a. Using screw pack “E” and screwdriver provided;
install three screws into the Light Assembly Adapter Plate,
as shown.
Step 11b. Step 24 B. Connect the Light Assembly
connector to the motor connector.
Step 11c. Carefully tuck the wires and align the keyhole
slots in the Light Assembly with the three screws in the
Adapter Plate. Turn counter clockwise to align the keyhole
slots with the three screws.
Step 11d. Securely tighten all three screws by hand only.
Install Incandescent Bulbs
Step 12. Screw in two 60-watt B-10 Candelabra-base
bulbs.
Glass Installation
Step 13a. Remove finial from Light Assembly.
Step 13b. Insert the threaded rod from the Light Assembly
through the hole in the glass shade, as shown.
Step 13c. Thread finial onto threaded rod. Tighten securely.
CAUTION:
Over tightening the finial can cause glass to break.
9
VERSA•TOUCH2™ CONTROL INSTALLATION
VERSA•TOUCH2™ HARDWARE (not to scale)
12v Battery
W-73
Control
Wood
Screw
1" (2)
Drywall Anchor
6-32 (2)
Screw
6-32 X 3/8"
(2)
Screw
6-32 X 1"
(2)
W-73
Control Holder
CONTROL BRACKET INSTALLATION
SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with
an isolating wall control/switch. CAUTION! Do not use with wall dimmer.
WARNING To reduce the risk of fire or electric shock, do not use this fan with any
solid state speed control device. Use only the ocntrol provided with this fan.
Step 8. Follow instructions for the type of transmitter control bracket you will be using.
Standard
Toggle
Switch
Inner
mounting
holes
Rocker
Light
Switch
Outer
mounting
holes
Switch
Cover
Plate
Switch
Cover
Plate
Control
Bracket
Control
Bracket
Standard Light Switch
Rocker Light Switch
Step A. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step A. Break off the two tabs by pushing outward.
Step B. Orient the control bracket as shown and line up
the two inner mounting holes with those on the switch.
Step C. Insert and tighten the screws using the provided
screwdriver.
Wall Installation
Step A. Locate a 2x4 wall
stud in a convenient
location.
Step B. Orient the control
bracket as shown over the
2x4 stud.
Step C. Insert the 1" wood
screws in either the inner
or outer mounting holes
and tighten using the
provided screwdriver.
Step B. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step C. Orient the control bracket as shown and line up
the two inner mounting holes with those on the switch.
Step D. Insert and tighten the screws using the provided
screwdriver.
NOTE: The wall anchors and 6-32 x 1" screws may be
used in situations where mounting to a stud is not possible.
Use the inner mounting holes. After securing the anchor,
discard the anchor’s pointed screws and use the 6-32 decor
ovalhead screws supplied.
Anchor
Panhead
Screw
Wood
Screw 1"
10
Drywall Anchor
Decor Ovalhead Screw
6-32 X 1"
SERRA™
REMOTE OPERATION
Fan Control
To start the fan. Press the selected speed button to run the fan at the desired speed.
Send Signal
LED
LOW=Low speed MED=Medium speed HIGH=High speed
UPLIGHT
To turn off the fan, press the FAN OFF button.
Airflow Direction
MED
To reverse the airflow, press the REVERSE button. REVERSE operates at any speed
whether the fan is on or off. The fan returns to its set speed after reversing.
LOW
Light Control
Turn the light on or off independently from the fan by pressing the LIGHT rocker
switch. (Press the left side for the uplight, right side for the downlight, and the middle for
both.) If you press the button for more than 0.7 seconds, it becomes a dimmer. The light
varies from “bright" to “dim” over approximately 8 seconds. If you continue to hold the
LIGHT button, this sequence will reverse when the light reaches its brightest or dimmest REVERSE
level. Release the button when the desired level is reached.
Auto Resume
Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains
the desired brightness level set previously.
DOWNLIGHT
HIGH
FAN
OFF
CHANGING TRANSMITTER FREQUENCY SETTING
Versa•Touch 2
Control
(back)
Note: All fans leave the factory set to “00000.”
You will only have to change the dip switch settings in the remote
if you are using more than one fan in the same area and want to
control them separately.
Step 1. At the circuit breaker or fuse box, turn the power off for
the fan you want to change.
Step 2. Open the battery door of the Versa•Touch control and
remove the batteries.
Step 3. Change the dip switch settings, assuring that they are
different from the previously installed Versa•Touch fan.
Step 4. Reinstall the batteries and the battery door on the control.
Step 5. At the circuit breaker or fuse box, turn the power back on
for the fan whose frequency you are changing.
Step 6. Within 20 seconds of restoring power, push the HIGH,
MED, and LOW buttons (in that order).
Note: You may want to label your controls to assure you do not
mix them up.
Dip Switch
set to “10000”
Dip Switch
set to “01001”
WARNING!
Do not turn the power off at the circuit breaker,
then back on, for the previously installed
Versa•Touch2 fan(s), as you may inadvertently
change the frequency settings for it as well.
2
If the fan is not functioning after installation:
Step 1. Check to make sure the batteries are installed correctly in
the control.
3
Step 2. Turn the power off to the fan (from the circuit breaker)
for at least 5 seconds.
Step 3. Turn the power back on (at the circuit breaker) and push
the HIGH, MED, and LOW buttons–in that order–within 20
seconds. The fan should now function properly.
Circuit Breaker
or Fuse Box
1
Press in this order to set new
frequency:
1. HIGH
2. MED
3. LOW
11
TROUBLESHOOTING TIPS
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
PROBLEM
POSSIBLE REMEDIES
Fan will not start
• Check the main circuit fuses, circuit breakers, and wall switch position. Check
all wire connections. Make sure the power is turned off during this inspection.
• The battery is weak. Install a fresh battery.
• The fan receiver is defective. Replace the fan receiver.
• Check the frequency setting: Turn the power off at the circuit breaker, for the
fan that is not functioning only. Check that the jumper switches match in both
the receiver and the transmitter.
Fan wobbles or shakes excessively
• Be sure the canopy pin is set properly into the slot on the ball.
• Check that the bladeholders have not been bent during installation and the
blades are balanced.
• The hanger bracket and/or the ceiling outlet are attached too loosely. Make
sure the hanger bracket is attached tightly to the ceiling outlet box and the
downrod assembly is secured firmly.
• The downrod is attached to the downrod base too loosely. Make sure all the
screws are securely tightened.
Fan is noisy during operation
• Check and tighten the light fixture retaining screws, glass shade screws, and/or
lightbulb(s).
• Tighten the canopy screws and mounting plate assembly. Make sure the wire
nuts inside the canopy and switch housing are not touching the metal parts and
that they have not fallen off the wire splices. Tighten as necessary.
• Tighten the blade holders to the flywheel (or direct drive motor) and the blades
to the bladeholder screws.
• Make sure all the screws in the motor housing are snug but not overly tight.
Fan does not run on low speed
• If fan is new, it may need to be “broken in.” Run at high speed for several days.
Battery life is short
• Replace with alkaline batteries.
Light works, but fan does not work
• The fan wires are not connected properly. Follow the instructions in Step 9.
Fan and light run only on full speed
• The fan receiver is defective. Replace the fan receiver.
Fan is missing one speed
• The fan receiver is defective. Replace the fan receiver.
Fan does not change speed, but light works • The fan receiver is defective. Replace the fan receiver.
Reverse does not work
• The fan receiver is defective. Replace the fan receiver.
Fan starts working by itself
• There is frequency interference. Change frequency as described on Page 11.
Fan operates only when transmitter is close • Check that antenna wire is not touching the metal plate.
Fan works, but light does not dim
• The fan receiver is defective. Replace the fan receiver.
Fan works, but light does not work
• The fan receiver is defective. Replace the fan receiver.
• The light socket is broken. Replace the socket.
• A lightbulb is defective. Replace the lightbulb.
12
SERRA™
CARE RECOMMENDATIONS
Fan Finishes
• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened
soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish.
Blades
• Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
• For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily using a mild
detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these
will damage the finish.
No Need for Lubrication
• N everlubri
catethisfan! The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated
for life.
• Do not attempt to oil the motor.
Changing Lightbulbs
• Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
• Replace bulbs with the same type as you removed from the light fixture.
• The maximum wattage rating for this fan’s light kit is 100 watts for the uplight, 120 watts for the downlight.
For questions or to locate the nearest Casablanca Authorized Service Center call toll free: 1-888-227-2178
or visit us on the web at: www.casablancafanco.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communication. However, there is no guarantee that the interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company
may void one's authority to operate this remote control.
13
AUTHORIZED SERVICE CENTERS
STATE/CITY
ZIP
SERVICE CENTER NAME
PHONE
ALABAMA
MOBILE
TUSCALOOSA
HUNTSVILLE
TYPE
36618
35405
35816
AZALEA CITY SERVICE CENTER
LTG. & APPL./LIGHTING PLUS
SOUTHERN HOME & HEARTH INC.
251-341-0663
205-345-8900
256-534-1715
ALASKA
ANCHORAGE
99518
PRIMARY ELECTRIC INC.
907-563-7988
ARIZONA
TUCSON
PHOENIX
GREEN VALLEY
SEDONA
PRESCOTT
LAKE HAVASU CITY
SCOTTSDALE
GLENDALE
PHOENIX
YUMA
MESA
MESA
TUCSON
YOUNGTOWN
TUCSON
85735
85019
85614
86336
86305
86403
85254
85308
85032
85364
85210
85204
85716
85363
85711
DESERT BREEZE FAN & ELEC.
520-623-4646
FAN-TASTIC ELECTRIC
602-866-1090
GOBLE ELECTRIC
520-625-4938
OAK CREEK AUDIO
928-282-5625
MARC PARENT/ELECTRICAL ETC. 928-778-5935
SOUND BANK ELECTRONICS
928-855-1129
VANDERVOORT ELECTRIC INC.
602-996-9637
BEA’S LAMPS & FANS
602-978-0004
THE BRASSWINDS SHOPPE
602-482-1881
CURLEY’S LITEHOUSE
520-782-4353
LOUD INC. DBA FANS PLUS
480-827-9302
GALLERY OF FANS
480-962-0477
ILLUMINATIONS ON BROADWAY LLC 520-325-3031
QUALITY HOME FAN DOCTOR
602-274-6649
SUN LIGHTING CO.
520-322-4303
ARKANSAS
LITTLE ROCK
72212
THE RANDY HALL CO. INC.
501-227-9915
ISO
ISO
OWTS
OWTS
CALIFORNIA
SANTA ROSA
GRASS VALLEY
JAMESTOWN
SANTA MARIA
AUBURN
SAN DIEGO
FRESNO
NEWHALL/SANTA
CLARITA
ATASCADERO
CLOVIS
SIMI VALLEY
CORONA
BAKERSFIELD
SAN MARCOS
STOCKTON
MOORPARK
SHINGLE SPRINGS
CATHEDRAL CITY
PLEASANTON
RIVERSIDE
TEMECULA
SO. LAKE TAHOE
CANYON LAKE
VALENCIA
SAN JOSE
SACRAMENTO
TULARE
FRESNO
SAN MARCOS
SAN DIEGO
RANCHO MIRAGE
MURRIETA
BAKERSFIELD
SAN FRANCISCO
TARZANA
CHICO
FRESNO
MANTECA
MISSION VIEJO
REDDING
CERRITOS
MODESTO
SAN RAFAEL
SANTA CRUZ
HUNTINGTON BEACH
SAUGUS
95404
95945
95327
93455
95603
92115
93704
91321
ASEF’S APPLIANCE SERVICE
ACCENT LIGHTING
DASILVA’S LAMP & CEILING
EVER-READY ELECTRIC
THE FAN DOCTOR
JOHN SHEPARD’S ELECT. SERV.
LARRY MC COLLUM
DAN MARTIN
707-575-3737
530-477-5483
209-984-4035
805-934-7091
530-823-8768
619-460-4132
559-438-5764
805-252-5769
93422
93612
93065
92881
93309
92069
95205
93021
95682
92234
94588
92505
92592
96150
92587
91354
95123
95819
93274
93710
92069
92111
92270
92562
93306
94109
91356
95928
93711
95336
92691
96002
90703
95350
94901
95062
92647
91350
MC NAMARA ELECTRIC INC.
OMEGA SERVICE INC.
PURCOM SYSTEMS
JERRY F. PRYOR
RB ELECTRIC & LTG.
RD ELECTRICAL CONTR.
RISSO ELECTRIC INC.
R.J. SIEG ELECT. CO.
JOHN ROZOWSKI CONST.
R & R SERVICE
S & L LIGHTING SERVICES
VERNE SMITH
TAB ELECTRIC
TAHOE POOL SERVICE
VILLAGE LIGHTS
FANTASTIC FAN SERVICE
SAL ZAMORA’S FAN REPAIR
A & A LIGHT FIXTURES
ANCHOR LIGHTING
ENERGY HOUSE
FAN DIEGO #1
FANDIEGO
FANDIEGO INC.
FANDIEGO #4
HILLCREST LTG-GALPIN INT
HOUSE OF FANS INC.
HYE LIGHTING CO.
J&J LIGHTING INC.
JAMES & CO LTG.
MANTECA LIGHTING
MOORE’S MISSION
NORTH VALLEY LIGHTING
COMFORTS OF HOME
PHILLIPS ELECTRIC CO.
RAFFLES
RIVERSIDE LIGHTING
THE TRADING POST
VALLEY BREEZE FAN CO
805-466-1854
ISO/OWTS,
559-299-0495
ISO
805-583-8171
909-279-7775
ISO
805-831-2438 15-MILE RADIUS
760-727-1215
209-466-0781
800-799-0808
530-677-3850
760-324-2942
925-895-3762
951-687-9552
951-303-0850
530-541-4958
951-244-2910
ISO
800-800-3871
510-742-5560
916-452-7641
ISO
209-688-0696
OWTS
559-432-1500
ISO
760-743-3267
ISO
619-292-9244
ISO
760-779-9916
ISO
951-600-7867
ISO/OWTS
805-324-9966
415-885-1947
ISO
818-345-5544
ISO/OWTS
530-342-1815
ISO
209-486-7900
ISO/OWTS
209-823-1999
ISO
714-859-7090 HOME/ISO/OWTS
530-221-6277
ISO/OWTS
562-865-6666
209-524-6287
OWTS
415-456-6660
ISO
831-423-7411
ISO
714-848-4353
OWTS
800-339-3267
COLORADO
LONGMONT
DENVER
80504
80229
L A ENTERPRISES
M.D ELECTRIC
800-299-0222
303-288-7988
ISO
TYPES OF SERVICE OFFERED:
ISO = IN-SHOP ONLY
14
OWTS = PRODUCT SOLD BY DEALER
ISO/OWTS = BOTH
STATE/CITY
ZIP
SERVICE CENTER NAME
PHONE
TYPE
LOVELAND
COLORADO SPRINGS
FORT COLLINS
LONGMONT
80538
80903
80525
80501
FIRESIDE LIGHTING INC.
HOME LIGHTING INC.
THE LIGHT CENTER
LUMENAREA.COM INC.
970-669-3540
719-471-3520
970-226-3430
303-485-8600
OWTS
OWTS
OWTS
OWTS
CONNECTICUT
NEW HARTFORD
BRIDGEPORT
CLINTON
EAST HARTFORD
WOODSTOCK
WILLINGTON
HARTFORD
GREENWICH
NEW HAVEN
06057
06605
06413
06118
06281
06279
06114
06830
06534
B.W. MORSE & SONS.INC.
FEDERAL ELECTRIC CONST.CO.
GRAHAM CO.
GRAHAM CO.
RANDY MATTEAU
GEORGE OPALENIK
CONNECTICUT LTG. CTR. INC.
FASHION LIGHT CENTER
NEW GRAND LIGHT
860-379-9855 10 -MILE RADIUS
203-334-6455
800-942-5575
800-942-5575
860-963-8979
860-684-4558
860-249-7631
ISO
203-869-3098
ISO, OWTS
203-777-5781
ISO
DELAWARE
DOVER
NEW CASTLE
19901
19720
BRUCE DRAJEM/ THE FAN MAN
ERIC SHURR
302-734-7737
302-998-5147
FLORIDA
WINTER HAVEN
GAINSVILLE
JACKSONVILLE
SOUTH DAYTONA
BOYNTON BEACH
WINTER HAVEN
NE PALM BAY
NAPLES
SPRINGHILL
DAVIE
NOKOMIS
CORAL GABLES
MAITLAND
DEERFIELD BEACH
TARPON SPRINGS
CLEARWATER
PUNTA GORDA
ORLANDO
TALLAHASSEE
PORT CHARLOTTE
BRANDON
NAPLES
33880
32608
32217
32119
33437
33884
32905
34110
34606
33330
34275
33134
32751
33442
34689
33765
33982
32807
32303
33952
33511
34109
ALL ABOUT FANS & LIGHTING
AUTHORIZED APPLIANCE SERV.
AUTHORIZED APPLIANCE SERV.
BOB’S FIX-IT
CMS
CYPRESS LIGHTING SHOWROOM
FAN DOCTOR/ M. FERRUZZO
GOODWIN ELECTRIC
FAN DOCTOR/KEN R. CHURCHES
LASERLAND INC.
GRAHAM ELECTRICAL CONTR.
MICHAEL HANSEN
HENRY ELECTRIC CO.
JARMO ELECTRIC INC.
PETER LONTAKOS ELECTRICAL
STEPHEN J. MERCER/ELECTRICAL
SELECT SERVICE & REPAIR
MID-FLORIDA FAN
JIM LACZKO/TODAY’S KIDS
JACKSONS LIGHTING INC.
LUMENAIR LTG. & FANS
WILSON LIGHTING OF NAPLES
863-299-9593
352-375-3886
ISO
904-737-5312
ISO
386-761-4055
561-736-0170 W PALM BEACH
800-975-2677
321-728-5638
239-649-8880
352-683-4428
854-558-3743
941-486-8190
305-444-4111
407-834-4032 IN SHOP ONLY
954-360-9024
727-938-8895\
727-712-3090
941-637-7850
407-893-6226
850-562-4661
941-625-0044
OWTS
813-653-3460
ISO
941-592-6006 OWTS/ISO ANY
GEORGIA
COLUMBUS
GRAYSON
WOODSTOCK
31904
30017
30188
GRADY GLASS DBA DAN’S FAN CITY 706-571-3242
RG TENNEY ELECTRIC
770-378-9255
BRUCE A. RUGG, GC
404-925-1133
HAWAII
KAILUA KONA
HILO
AIEA
KAILUA KONA
KAHULUI
96740
96720
96701
96740
96732
KU’S ELECTRONIC SVC.
BAY LIGHTING & DESIGN
THE FAN SHOP, INC.
KONA COAST HOUSE OF LTS. INC.
READ LIGHTING
808-329-4346
808-961-5688
808-488-1221
808-329-0748
808-871-8995
IDAHO
MERIDIAN
IDAHO FALLS
83642
83402
S-K ELECTRIC, INC.
HOME LIGHTING
208-941-6264
208-523-2300
ILLINOIS
CENTRALIA
RICHMOND
CHICAGO
PRINCETON
CHAMPAIGN
BELLEVILLE
SPRINGFIELD
NORMAL
SPRINGFIELD
CORNLAND
QUINCY
TRENTON
CHAMPAIGN
YORKVILLE
62801
60071
60630
61356
61821
62223
62704
61761
62707
62519
62301
62293
61821
60560
BAKER APPLIANCE REPAIR
CARAVELLE LIGHTING INC.
D & S FAN SPECIALTIES INC.
ELMORE ELECTRIC INC.
TERRY GOBBLE
JOHN HASSENSTAB
HOME WORKS INC.
KIRK SMALL APPLIANCE
SHAWN SCHALK
DELMAR VEECH
HEINTZ LIGHTING CENTER
LITE BRITE DIST
SPRINGFIELD ELEC SPLY #3
UNIFIED SUPPLY INC.
618-532-8437
815-678-4558
847-824-2430
815-643-2354
217-384-5891
618-398-4640
217-753-3305
309-452-5248
217-585-0670
217-364-4121
217-223-0101
618-224-7314
217-351-7600
630-553-0660
INDIANA
EVANSVILLE
FORT WAYNE
GREENFIELD
VALPARAISO
INDIANAPOLIS
47711
46805
46140
46383
46222
MICHAEL BAXTER
CARL J. SMITH
D & D REPAIR
D & K ELECTRIC
INDIANA LTG. CTR.INC.
812-453-6498
260-484-7295
317-467-0600
219-464-7576
317-293-9333
ISO
IOWA
CEDAR RAPIDS
SIOUX CITY
SIOUX CENTER
DES MOINES
52404
51106
51250
50311
ACME ELECTRIC COMPANY
DIVERSIFIED ELECTRONICS
HILLS HOME SYSTEMS
ADVANCED LIGHTING
319-365-8677
712-276-1034
712-722-2539
515-255-5009
OWTS
ISO
OWTS
ISO
IN SHOP ONLY
NO IN SHOP
ISO
ISO
ISO
SERRA™
STATE/CITY
ZIP
SERVICE CENTER NAME
PHONE
TYPE
IOWA (CONTINUED)
MONTICELLO
CARROLL
CORALVILLE
DAVENPORT
52310
51401
52241
52803
REM ELECTRIC INC.
J & L ELECTRIC INC.
RALSTON CREEK
SHAW ELECTRIC INC.
319-465-3346
712-792-2444
319-351-2189
563-323-3611
KANSAS
WICHITA
EMPORIA
OVERLAND PARK
OVERLAND PARK
WICHITA
MANHATTAN
TOPEKA
LENEXA
SALINA
OVERLAND PARK
OVERLAND PARK
67211
66801
66213
66210
67226
66502
66611
66215
67401
66223
66212
ACTION APPLIANCE SERVICE INC.
C.A.P.
KAL ELECTRIC INC.
RANDY RUSSELL
ACCENT LTG INC.
ENDACOTT LIGHTING
K & S LIGHTING
RENSEN HOUSE OF LIGHTS
SALINA APPL. SHOWROOM
WESTERN CHANDELIER CO.
WILSON FANS & LIGHTING
316-263-0652
316-342-0448
913-897-6767
913-338-5330
316-636-1278
785-776-4472
785-267-0422
913-888-0888
785-827-1420
913-685-2000
913-642-1500
KENTUCKY
LEXINGTON
40510
CHARLET ELECT./RON CHARLET
606-231-7344
LOUISIANA
LAFAYETTE
HOUMA
BATON ROUGE
MONROE
NEW IBERIA
LAKE CHARLES
METAIRIE
70501 ACADIA SERVICE CO.
70363 GULF SOUTH ARMATURE
70815 HOME APPLIANCE SERVICE
71201 ALBERT SURLCO
70560 WALET’S INC.
70601 JOSEPH’S ELECTRICAL CTR INC.
70006 ROMAINE’S
318-233-8910
985-872-0486
504-272-7725
318-699-0619
318-364-7486
318-436-4930
504-887-7077
ISO
ISO
ISO
MAINE
SOUTH PORTLAND
04106
T.A. NAPOLITANO
207-799-0538
NO CLIPS
MARYLAND
FREDERICK
WHITE HALL
FORESTVILLE
21704
21161
20747
GL FAN SERVICE
BT ELECTRIC/BILL TYRRELL
BURGESS LIGHTING
301-831-4925
410-329-6353
301-568-8000
ISO
OWTSH/ISOA
ISO
ISO
ISO,OWTS
MASSACHUSETTS
S. ATTLEBORO
BRIDGEWATER
MAYNARD
W SPRINGFIELD
NATICK
DANVERS
DENNIS
WORCESTER
NEW BEDFORD
ORLEANS
02703 AJ ELECTRIC
02324 BILTCLIFFE ELECTRIC
01754 HOUSE DOCTOR
01089 JALBERT ELECTRIC
01760 J.G. ELECTRIC CO INC.
01923 PLAZA LIGHTING
02638 RICK SEXTON
01603 EDWARD A. TORTORA
02740 VANDER ELECTRIC & EQUIP. CO.
02653 ASSOCIATED ELECTRICAL SERV.
508-761-5021
508-697-7630
978-897-9085
413-734-4976
508-653-3042
978-774-7801
508-385-7536
508-755-3735
508-993-6383
508255-4589
MICHIGAN
BELLEVILLE
LANSING
LANSING
TRAVERSE CITY
HOWELL
BIRMINGHAM
GRAND RAPIDS
KALAMAZOO
48111
48906
48917
49686
48855
48009
49512
49002
734-699-9698
517-484-0300
517-627-4229
231-938-1332
810-227-3375
248-645-6464
616-949-4931
269-343-4428
MINNESOTA
ROCHESTER
MINNEAPOLIS
MAPLEWOOD
MINNEAPOLIS
PLYMOUTH
BURNSVILLE
EDEN PRAIRIE
ST. PAUL
BAXTER
55906 KROUPA’S ELECTRONICS
55422 LEO’S ELECTRIC SALES & SERVICE
55109 NORTH COUNTRY ELECTRIC
55411 PENN ELEC. MOTOR SERV.
55441 FAN MAN #101 (FLOWC #21)
55337 FAN MAN #102 (FLOWC #22)
55344 FAN MAN #106 (FLOWC#26)
55108 FAN MAN #107 (FLOWC #27)
56425 THE LIGHT DEPOT
507-281-4064
612-546-5625
651-748-4027
612-588-5333
612-559-0761
612-898-2754
612-941-9243
651-649-0686
218-829-0770
ISO
ISO
ISO
ISO
ISO
MISSISSIPPI
MADISON
OCEAN SPRINGS
39110
39564
601-856-9469
228-872-7181
ISO
MIKE AYERST
INTEGRITY ELECTRIC
LARGENT ENTERPRISES INC.
CREATIVE LTG. & RESTORATION
LIGHTNING ELECTRIC INC. CO
21ST CENTURY ELECTRIC
GRAND RAPIDS LTG. CTR. INC.
HODGSON ENTERPRISES
JACKSON SERVICE CTR.
KELLY’S APPLIANCE
MISSOURI
SPRINGFIELD
ST LOUIS
SPRINGFIELD
BRANSON
65802
63123
65804
65616
COMPLETE MAINTENANCE
LEINWEBER SERVICE CO.
LOYD’S ELECT/LIGHTHOUSE GALL.
LOYD’S ELECTRIC SUPPLY INC.
417-866-2700
314-892-8177
417-889-1088
417-334-2171
MONTANA
KALISPELL
HELENA
MISSOULA
59901
59601
59801
LASALLE LIGHTING
SUPREME LIGHTING
WESTERN MONTANA LTG SPY
406-752-2424
406-442-8200
406-543-7166
NEBRASKA
OMAHA
GRAND ISLAND
OMAHA
68104
68803
68144
D & L ELECTRONICS
QUALITY SEW & VAC.
OAK HILLS ELECTRIC INC.
402-571-5233
308-382-7310
402-691-4567
20 MI. RAD.
ISO
ISO
ISO
ISO
ISO
OWTS,ISO
OWTS
SECONDARY
ISO
ISO
STATE/CITY
ZIP
SERVICE CENTER NAME
PHONE
NORFOLK
LINCOLN
68701
68510
THE POWER STATION/FROHBERG ELEC.402-371-6671
LINCOLN LIGHTING CTR.
402-476-1297
NEVADA
SPARKS
LAS VEGAS
LAS VEGAS
89431
89103
89119
EAGLE ELECTRIC, INC.
KS&S ELECTRIC, LLC
FANCO
775-356-7300
702-222-9306
702-898-8522
NEW HAMPSHIRE
NEW IPSWICH
EXETER
NASHUA
03071
03833
03060
HOUSE DOCTOR
EDWARD HEINE
AFFORDABLE FANS ETC.
603-731-5036
603-772-2359
603-759-8332
NEW JERSEY
BELLMAWR
WASHINGTON
TRENTON
THOROFARE
MORRIS PLAINS
LINWOOD
RANDOLPH
W. LONG BRANCH
MULLICA HILL
JACKSON
CHESTER
PARK RIDGE
08031
07882
08619
08086
07950
08221
07869
07764
08062
08527
07930
07656
JOSEPH ASHLEY
C.P. ORLANDO
WIRING UNLTD./RICHARD DOBRON
HARRY R. HABICHT
MANNY HERRERA
JACK BRESLAU-HANDYMAN SVCS.
ANTHONY MAKOMASKI
CHRIS KIBBE/NO SHORTS ELECTRIC
STEPHEN RICE
ROBERT ROLZHAUSEN
CHESTER LIGHTING, INC.
KRELL LIGHTING
609-694-3785
908-689-4750
609-584-1122
856-845-2541
973-993-1137
609-601-1797
908-475-5569
732-222-4228
856-223-8645
732-363-3729
908-879-7200
201-391-7685
NEW MEXICO
ALBUQUERQUE
ROSWELL
ALBUQUERQUE
ALBUQUERQUE
87123
88201
87112
87109
FRANK’S ELECTRIC
J & G ELECTRIC CO.
A-1 LAMP DOCTOR
B-ELECTRIC
505-293-6724
505-622-0146
505-296-5050
505-828-0241
NEW YORK
COMMACK
BROOKLYN
ALBANY
E. MEADOW
BUFFALO
QUEENSBURY
HASTINGS
BUFFALO
PLAINVIEW
NEWBURGH
STATEN ISLAND
YONKERS
POUGHKEEPSIE
ROCHESTER
LONG BEACH
SHOKAN
LYNBROOK
STATEN ISLAND
REGO PARK
AMHERST
SCHENECTADY
TROY
COMMACK
STATEN ISLAND
PEARL RIVER
BEDFORD
CARLE PLACE
BROOKLYN
BROOKLYN
NANUET
AMHERST
NEW YORK
11725 AIR-TEK DBA REPUBLIC LIGHTING 631-499-1854
11204 JERRY PICCOLINO/J&R SERVICE
718-259-1789
12205 BERT ELECTRIC
518-869-7140
11554 C.D. SERVICE
516-538-3481
14206 CRAFTMASTERS SERVICENTER
716-893-9557
12804 DEAN ELECTRIC
518-792-4781
13076 ELECTRICAL WORK BY MARTY
315-668-0220
14226 THE FAN COLLECTION, INC.
716-839-2447
11803 JOSEPH GOTTDANK
516-932-7618
12550 J D PARRELLA ELECT.
845-562-4112
10312 JOE VALLETUTTI JR..
718-608-9008
10704 JAY D. KOSACK
914-237-9051
12601 MANNINO ELECTRIC INC.
914-452-3520
14620 BARRY MALADY DBA CAM ELECTRIC 585-271-8560
11561 NICK’S IMPROVEMENT COMPANY 516-659-8989
12481 OLIVE FANS & LTG.
845-657-5823
11563 SHADERITE-PZ REPAIR
516-593-8973
10301 FRANK RAGUCCI/F&R SERVICE CNTR. 718-273-5518
11374 MARK RALIN
718-896-7844
14228 SHANOR LTG. CTR.
716-691-3622
12303 FRANK SALVATORE
518-355-5789
12180 TROY LIGHT COMPANY
518-274-6931
11725 TURNPIKE APPLIANCE
631-499-3355
10304 V & P SERVICE CO/VITO PICCOLINO 718-447-7945
10965 BOB VAZQUEZ
845-735-5861
10507 BEDFORD LIGHTING INC.
914-666-0680
11514 LIGHTING CTR. BY CAMEO INC.
516-747-4748
11219 MAIN LAMP CORP.
718-436-2207
11223 MANHATTAN LIGHTS INC.
718-998-1111
10954 NOVA LIGHTING, INC.
914-623-5211
14226 ROYALITE INC.
716-832-1492
10003 SUPERIOR LIGHT & FAN
212-677-9191
NORTH CAROLINA
SALISBURY
CHARLOTTE
HICKORY
CHARLOTTE
28146
28205
28602
28203
HAUSS ELECTRICAL SERV.
EFIRD’S INTERIORS, INC.
EFIRD’S INTERIORS, INC.
SIMPSONS LIGHTING /LT.FIXT
704-637-7774
704-376-5648
704-322-2203
704-376-5463
NORTH DAKOTA
FARGO
58102
MIDSTATES ELECTRIC INC.
701-293-0441
OHIO
CANTON
COLUMBUS
LOVELAND
MAUMEE
DAYTON
COLUMBUS
CLEVELAND
N. OLMSTED
NORTH LIMA
SOUTH EUCLID
DAYTON
44706
43235
45140
43537
45419
43231
44109
44070
44452
44121
45459
APPLIANCE PARTS CO.
CERTIFIED SYSTEMS
HANK GRINSHPAN
K.O.V ELECTRONIC REPAIR
LARKIN ELECTRIC CO.
THE LAMP LIGHTER
WESTSIDE LTG. CTR.
CHANDELIER SHACK INC.
DICKEY ELECTRIC
LAMPSHADER EAST/DBA LTG. EXPO
OHIO LAMP & FIXTURE CO.
330-453-8077
614-799-0778
513-683-8666
419-865-8893
937-294-4115
614-891-7940
216-459-1970
440-777-6969
330-549-3976
216-291-3030
937-439-0822
TYPE
20 MI. RAD.
ISO
OWTS
OWTS
ISO
SANTA FE
ISO
20-MI. RAD.
ISO
IN SHOP
QUEENS
ISO
ISO
20-MI. RAD.
ISO
ISO
ISO
ISO
ISO
ISO
ISO
OWTS
ISO
ISO
OWTS/ISO
ISO
15
STATE/CITY
ZIP
SERVICE CENTER NAME
PHONE
TYPE
OKLAHOMA
OKLAHOMA CITY
OKLAHOMA CITY
OKLAHOMA CITY
73105
73132
73127
APPLIANCE SERVICE BY CK
LARKIN E. STEVENSON
JAMES LIGHTING INC.
405-525-8862
405-728-8810
405-947-6663
OREGON
PORTLAND
BEND
97225
97701
SYLVAN ELECTRONICS INC.
DESIGN LIGHTING INC.
800-473-1244
541-389-9997
PENNSYLVANIA
HOPWOOD
DREXEL HILL
ALLENTOWN
PITTSBURGH
PHILADELPHIA
EASTON
ALLENTOWN
LANCASTER
WEST CHESTER
FAIRLESS HILLS
WEST READING
HARRISBURG
CONSHOHOCKEN
WILLOW GROVE
STATE COLLEGE
15445
19026
18105
15224
19111
18045
18102
17601
19382
19030
19611
17111
19428
19090
16803
GEORGE R. SMALLEY CO. INC.
PATRICK HASTINGS
LIGHTING FIXTURE & SUPPLY CO
MARK DIULUS ELECTRIC CO.
KLAUS OTTE
PRIMROSE ELECTRICAL
SCHOLL’S ELECTRIC
S. DEAN’S ELECTRIC
TOBIAS ELECTRIC
ASTRO LTG. GALLERIES
A TO Z VACUUM STORES
YALE ELECTRIC SUPPLY
KAY ELECTRIC SUPPLY
NORTH-WEST ELEC. SUPPLY CO.
WHITEHILL LIGHTING & SPLY.
724-437-1927
610-853-2709
610-435-9691
412-681-2553
215-745-4266
610-258-1359
610-435-5876
717-2854545
610-942-4000
215-943-0331
610-374-4888
717-233-8401
610-825-0100
215-659-5757
814-238-2449
RHODE ISLAND
PAWTUCKET
02861
WICKFORD APPLIANCE & LTG CTR. 401-726-4240
ISO
SOUTH CAROLINA
HANAHAN
SPARTANBURG
BLUFFTON
GOOSE CREEK
MYRTLE BEACH
COLUMBIA
29406
29306
29910
29445
29575
29212
BOBBY LUTES ELECTRICAL INC.
BOBBY JACKSON ELECTR.
J. HEAVENER & CO.
DAVID MIMS
RAY ELECTRIC
EASTWIND ENTERPRISES
843-797-0948
803-583-6035
843-837-8300
843-514-2380
843-293-0068
803-781-3267
ISO
SOUTH DAKOTA
SIOUX FALLS
SIOUX FALLS
57105
57104
LAMPS AND SHADES INC.
MAHLANDER’S
605-332-6680
605-336-7798
TENNESSEE
MT CARMEL
MEMPHIS
LOUISVILLE
BRENTWOOD
37645
38111
37777
37027
APPALACHIAN ELEC. SVC.
APPLIANCE SERVICE CTR.
BEN SNYDER
PAUL TAMPIEN/SUNSHINE ELECT.
423-357-0783
901-324-5898
865-380-5491
615-371-9383
TEXAS
LEWISVILLE
HOUSTON
CORPUS CHRISTI
FREEPORT
AMARILLO
DENTON
ODESSA
DENTON
DAMON
KERRVILLE
PARIS
SAN ANTONIO
AUSTIN
GIDDINGS
LUBBOCK
75067
77089
78404
77541
79106
76201
79761
76201
77430
78029
75460
78212
78757
78942
79413
SOUTHERN COMFORTS
BENNETT FAN INSTALL., INC.
BRAND APPLIANCE & MICROWAVE
SKIP’S ELECTRIC AND AIR
DI’S LAMP & FAN REPAIR
FANTASIA CEILING FANS
GOFORTH ELECTRIC
LARRY W. GOFF
GULF COAST FAN SERVICE
MAURICE HAMMIT
HARGIS ELECTRIC
CEILING FAN SERVICE CTR.
KLOCK ELECTRIC
ORSAG’S INC.
ORECK VACUUMS
940-536-1406
281-484-1401
512-854-1851
979-233-3903
806-331-5267
940-484-4222
432-550-8927
940-387-7304
281-495-6434
210-367-4937
903-785-8055
210-804-1362
512-837-4704
409-542-3167
806-792-2821
ISO
ISO
IN HOME ONLY
ISO
OWTS
ISO
ISO
ISO
ISO
ISO
STATE/CITY
ZIP
SERVICE CENTER NAME
PHONE
ARLINGTON
TYLER
XHEARE
CARROLLTON
HUMBLE
AUSTIN
HOUSTON
RICHARDSON
HURST
BEAUMONT
DALLAS
VICTORIA
SAN ANGELO
WICHITA FALLS
HOUSTON
HARLINGEN
MCALLEN
SEALY
76001
75707
77859
75006
77338
78703
77069
75080
76053
77702
75206
77904
76904
76308
77063
78550
78504
77474
P&M QUALITY CONT.
CHARLES R. RAINS
THOMPSON SUPPLY
ADFANTAGE CEILING FAN
CAROLS LTG. & FAN SHOP
TEXAS CEILING FANS/CEILING FAN SHOP
CHAMPIONS LIGHTING
COOL BREEZES
ARC FAN & LIGHTING
FAN FACTORY
LIGHTS FANTASTIC
HALL ELECTRIC CO., INC.
HERITAGE HAUS
LANTERN HOUSE INC.
LIGHTING PLUS INC.
THE LIGHT HOUSE
THE LIGHT HOUSE
TEXAS CEILING FANS
817-478-2004
903-566-3119
409-280-5737
972-446-9393
281-446-7613
512-477-3132
281-440-5339
972-690-4580
817-268-2218
409-833-8207
214-987-9655
512-578-6221
325-949-6541
940-692-7381
713-784-2440
956-423-6664
956-631-1155
979-885-6900
UTAH
MURRAY
RIVERTON
LAYTON
84107
84065
84040
CENTRAL ELECTRIC CO.
VERN O. FRANCIS
HARUO YOSHIKAWA
801-467-5479
801-254-4178
801-546-6008
VIRGINIA
RICHMOND
BURKE
WILLIAMSBURG
VIRGINIA BEACH
23228
22015
23185
23451
FANNING ELECTRICAL SERVICE
L&S ELECTRIC INC.
TAPROOT COMPANY
FANS,LIGHTING, ‘N’ MORE
804-262-3681
703-237-0011
757-229-3722
757-422-3616
WASHINGTON
SPOKANE
TACOMA
WENATCHEE
PASCO
BELLINGHAM
YACOLT
YAKIMA
99216
98404
98801
99301
98225
98675
98902
BRITE-WAY ELECTRIC
509-922-0275
M.G.M. ELECTRONICS
253-752-9826
SEW CREATIVE/ADVANTAGE STORE 509-663-5516
ARHA TOTAL SERVICE
509-547-3799
JOHN WIGGINS DBA TWIN SISTER’S ELEC. 360-676-1257
S&L ELECTIRC
503-657-0633
INLAND LIGHTING
509-248-4647
ISO
WASHINGTON, DC
WASHINGTON
20007
FAN FAIR
202-342-6290
ISO
WEST VIRGINIA
SO. CHARLESTON
WHEELING
25309
26003
PEPPER ELECTRIC
TOP HAT STOVE SALES
304-768-8195
304-233-6262
WISCONSIN
MILWAUKEE
GREEN BAY
FONTANA
BROOKFIELD
MADISON
LA CROSSE
53219
54313
53125
53005
53719
54601
BOB’S FAN REPAIR
KARL DEVROY
J&L PROPERTY MAINT.
CITY LIGHTS & FANS
MADISON LIGHTING
WETTSTEIN’S
414-546-2501
920-494-6090
262-275-2345
414-781-9048
608-271-6911
608-784-5555
CANADA
TORONTO, ONT.,
M6M2P5 ZANEEN LIGHTING
416-247-922
OVERSEAS
ST. THOMAS
00805
809-775-2399
DUANE LOBERG
TYPE
ISO
ISO
ISO
ISO,OWTS
ISO
ISO
ISO
OWTS
OWTS
ISO
ISO
ISO/OWTS
PRODUCT SPECIFICATIONS
Collection:
Model Name:
Model Number:
Cosmopolitan
Serra™
P3M64M
Dimensions:
A = 11"
B = 16"
C = 3"
D = 16"
E =5.6"
NOTE: Dimension B
includes light fixture
and glass.
Weight:
16
36 lbs.
Finishes:
Blade Finishes:
Glass Finish:
Motor:
Blade Span:
Blade Iron Pitch:
No. of Blades:
TTechnology:
Lightbulbs:
Russet
Walnut / Dark Walnut
Textured Scavo
188 x 25mm Direct DriveTM
56"
15°
5
Versa•Touch2® / W-73
(4) 25-watt S11 bulbs
(2) 60-watt B-10 bulbs
(Candelabra-base)
Download PDF