Emerson | 1410 | Product Data Sheet: Emerson Smart Wireless Gateway Solutions

Product Data Sheet
August 2014
00813-0300-4410, Rev AB
Emerson Smart Wireless Gateway Solutions

Gateway connects the WirelessHART® self-organizing networks with any host system

Easy configuration and management of self-organizing networks

Easy integration into control systems and data applications through serial and Ethernet
connections

Seamless integration into AMS® Device Manager

Greater than 99% data reliability with industry proven security

Smart Wireless capabilities extend the full benefits of PlantWeb® architecture to previously
inaccessible locations
Smart Wireless Gateway
August 2014
Introduction
Gain real-time process information with greater than 99% wireless data
reliability

The Emerson Smart Wireless Gateway 1410 automatically manages wireless communications in
constantly changing environments

Native integration with Ovation automation system provides simple and fast commissioning for
wireless field networks

Connect to data historians, legacy host systems, and other applications through Ethernet,
Modbus®, Serial, OPC, EtherNet/IP, and HART® outputs
Complete wireless network configuration tools
provided with each Emerson Smart Wireless Gateway
Solution

The integrated web interface allows easy configuration of the
wireless network and data integration without the need to install
additional software

Complimentary AMS Wireless Configurator software provides
Emerson Device Dashboards to configure devices and view
diagnostic data

Drag and drop device provisioning enables a
secure method to add new wireless devices to
the wireless field network
Contents
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
1410 Gateway Product Certifications . . . . . . . . . . . . . page 9
Model 1410 Ordering Information . . . . . . . . . . . . . . . . page 5
Model 781 Product Specifications . . . . . . . . . . . . . . . page 10
Model 781 Ordering Information . . . . . . . . . . . . . . . . . page 6
Model 781 Product Certifications . . . . . . . . . . . . . . . page 11
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . page 13
1410 Gateway Product Specifications . . . . . . . . . . . . . . page 8
2
Smart Wireless Gateway
August 2014
Specifications
Self-organizing network specifications
System security specifications
Protocol
Ethernet

IEC 62591(WirelessHART), 2.4 - 2.5 GHz DSSS

Maximum network size
Secure Sockets Layer (SSL) enabled (default) TCP/IP
communications
Emerson Smart Wireless Gateway access

100 wireless devices @ 8 sec. or greater
Supported device update rates

1, 2, 4, 8, 16, 32 seconds or 1 - 60 minutes

For information on network size and update rate, please see
the capacity estimator tool on the Smart Wireless homepage
http://www.emersonprocess.com/Wireless

Self-organizing network

Network size/latency

100 Devices: less than 10 seconds

50 Devices: less than 5 seconds
AES-128 Encrypted WirelessHART, including individual session
keys. Drag and Drop device provisioning, including unique
join keys and white listing.
Internal firewall

Data reliability

Role-based Access Control (RBAC) including Administrator,
Maintenance, Operator, and Executive. Administrator has
complete control of the Gateway and connections to host
systems and the self-organizing network.
Greater than 99%
User configurable TCP ports for communications protocols,
including Enable/Disable and user specified port numbers.
Inspects both incoming and outgoing packets.
Third party certification

Wurldtech: Achilles Level 1 certified for network resiliency

National Institute of Standards and Technology (NIST):
Advanced Encryption Standard (AES) Algorithm conforming
to Federal Information Processing Standard Publication 197
(FIPS-197)
3
Smart Wireless Gateway
August 2014
Emerson’s Smart Wireless Solution
IEC 62591 (WirelessHART)... the industry standard
Self-organizing, adaptive mesh routing

No wireless expertise required, network automatically finds the best communication paths

The self-organizing, self-healing network manages multiple communication paths for any given device. If an obstruction is
introduced into the network, data will continue to flow because the device already has other established paths. The network will
then lay in more communication paths as needed for that device.
Reliable wireless architecture

Standard IEEE 802.15.4 radios

2.4 GHz ISM band sliced into 15 radio-channels

Time Synchronized Channel Hopping to avoid interference from other radios, WiFi, and EMC sources and increase reliability

Direct sequence spread spectrum (DSSS) technology delivers high reliability in challenging radio environment
Emerson’s Smart Wireless
Seamless integration to all existing host systems

Native integration into Ovation is transparent and seamless

Gateways interface with existing host systems using industry standard protocols including OPC, Modbus TCP/IP, and Modbus RTU
Layered security keeps your network safe

Ensures that data transmissions are received only by the Smart Wireless Gateway

Network devices implement industry standard Encryption, Authentication, Verification, Anti-Jamming, and Key Management

Third party security verification including Achilles and FIPS197.
4
August 2014
Smart Wireless Gateway
Model 1410 Ordering Information
Table 1. Smart Wireless Gateway Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Product description
1410
Smart Wireless Gateway, 2.4 GHz DSSS, WirelessHART, Webserver, AMS Ready, HART IP
★
Wireless configuration
D(1)
100 Device Network with Rosemount Field Link 781 (10.5-30 VDC)
★
Ethernet communications - physical connection
1(2)(3)
Single Ethernet Connection
★
2(4)(5)
Dual Ethernet Connection
★
Serial communication
N
None
★
A(6)
Modbus RTU via RS-485
★
Ethernet communication - data protocols(7)
D1
Modbus TCP/IP
★
D2
OPC
★
D3
EtherNet/IP
★
D4(7)
Modbus TCP/IP, OPC
★
D5(7)
EtherNet/IP, Modbus TCP/IP
★
D6(7)
EtherNet/IP, OPC
★
E2
Ovation Ready
★
E3(8)
Webserver Only
★
Antenna options
WNA
For use with the 781 Remote Field Link
★
1410 product certifications
NA
No Approvals
★
Redundancy options
RD
(1)
Gateway Redundancy
★
Must order the remote field link (781). Reference Model 781 Ordering Information on page 6 for details.
(2) Single active 10/100 baseT Ethernet port with RJ45 connector.
(3) Additional ports disabled.
(4) Dual active 10/100 baseT Ethernet ports with RJ45 connectors.
(5) Multiple active ports have separate IP addresses, firewall isolation, and no packet forwarding.
(6) Convertible to RS232 via adapter, not included with Gateway.
(7) Selection of Dual Ethernet option code 2 is recommended.
(8) Requires (A) Modbus RTU via RS-485 Communication protocol.
5
Smart Wireless Gateway
August 2014
Model 781 Ordering Information
Table 2. Smart Wireless Gateway Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Product description
781
Smart Wireless Field Link
★
Physical connection
RS485
★
D
Dual Compartment Housing - Aluminum
★
E
Dual Compartment Housing - Stainless Steel
★
A1
Housing
Conduit threads
1
1/2 - 14 NPT
★
2
M20 (included thread adapter required for M20 use)
★
781 product certifications
I5(1)
FM Intrinsically Safe, Non-incendive
★
I6(1)
CSA Intrinsically Safe
★
I1(1)
ATEX Intrinsically Safe
★
I7(1)
IECEx Intrinsic Safety
★
KL(1)
FM & CSA Class 1 Division 1, ATEX Zone 0 Intrinsically Safe
★
NA
No Approvals
★
Wireless update rate, operating frequency, and protocol
WA3
User Configurable Update Rate, 2.4 GHz DSSS, WirelessHART
★
Omnidirectional wireless antenna and SmartPower™
WK3
External Antenna, Line Power 10 - 30 VDC
★
WM3
Extended Range, External Antenna, Line Power 10 - 30 VDC
★
LCD Display
★
Display
M5
Gland and connector options
G2
Cable Gland (7.5 mm - 11.9 mm)
G4
Thin Wire Cable Gland (3 mm - 8 mm)
Typical model number:
781 A1 D 1 KL WA3 WK3 M5
(1) Use of the 781 with a 1410 Smart Wireless Gateway requires the use of an appropriate Intrinsically Safe Barrier.
6
Smart Wireless Gateway
August 2014
Accessories
Table 3. Accessories
Item description
Part number
Serial Port HART Modem and Cables only
03095-5105-0001
USB Port HART Modem and Cables only
03095-5105-0002
7
Smart Wireless Gateway
August 2014
1410 Gateway Product Specifications
Functional specifications
Communication specifications
Input voltage
Isolated RS-485
10.5-30 VDC
2-wire communication link for Modbus RTU multidrop
connections
Current draw
Operating current draw is based on 3.6 Watts power
consumption.
Protocol: Modbus RTU
Wiring: Single twisted shielded pair, 18 AWG. Wiring distance is
approximately 4000 ft. (1,524 m)
250
Current (mA)
Baud rate: 57600, 38400, 19200, or 9600
Ethernet
Operating
Region
125
12
10/100base-TX Ethernet communication port
24
30
Protocols: Modbus TCP, OPC, EtherNet/IP, HART-IP, https (for
Web Interface)
Voltage (VDC)
Wiring: Cat5E shielded cable. Wiring distance 328 ft. (100 m).
Environmental
Modbus
Operating temperature range:
-40 to 167 °F (-40 to 75 °C)
Supports Modbus RTU and Modbus TCP with 32-bit floating
point values, integers, and scaled integers.
Operating humidity range:
0-100% relative humidity
Modbus Registers are user-specified.
EMC performance
Complies with EN61326-1:2006.
Antenna options
See 781 specifications.
Physical specifications
Weight
0.70 lb. (0,318 kg)
Material of construction
Housing
Polycarbonate
Rail mount
Top hat rail EN 50022 35 mm X 7.5 mm and 35 mm x 15 mm
8
OPC
OPC server supports OPC DA v2, v3
EtherNet/IP
Supports EtherNet/IP protocol with 32 bit Floating Point values
and Integers. EtherNet/IP Assembly Input-Output instances are
user configurable. EtherNet/IP specifications are managed and
distributed by ODVA. For details on capabilities please see the
Smart Wireless Gateway to Allen Bradley Integration Manual
(document number 00809-0500-4420) on rosemount.com.
August 2014
Smart Wireless Gateway
1410 Gateway Product Certifications
Approved Manufacturing Locations
Rosemount Inc. – Chanhassen, Minnesota, USA
Emerson Process Management Asia Pacific Private Limited Singapore
Telecommunication Compliance
All wireless devices require certification to ensure that they
adhere to regulations regarding the use of the RF spectrum.
Nearly every country requires this type of product certification.
Emerson is working with governmental agencies around the
world to supply fully compliant products and remove the risk of
violating country directives or laws governing wireless device
usage.
FCC and IC
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following conditions: This device may not cause
harmful interference. This device must accept any interference
received, including interference that may cause undesired
operation. This device must be installed to ensure a minimum
antenna separation distance of 20 cm from all persons.
European Directive Information
The EC declaration of conformity can be found on page xx. The
most recent revision can be found at
www.emersonprocess.com.
Ordinary Location Certification from FM
Approvals
As standard, the transmitter has been examined and tested to
determine that the design meets basic electrical, mechanical,
and fire protection requirements by FM Approvals, a nationally
recognized testing laboratory (NRTL) as accredited by the
Federal Occupational Safety and Health Administration (OSHA).
9
Smart Wireless Gateway
August 2014
Model 781 Product Specifications
Functional specifications
Performance specifications
Output
ElectroMagnetic Compatibility (EMC)
IEC 62591 (WirelessHART), 2.4 GHz DSSS
All Models:
Meets all relevant requirements of EN 61326-1; 2006
Local display
The optional five-digit integral LCD Display can display wireless
information.
Humidity limits
0–99% Non-condensing Relative Humidity
Radio frequency power output from antenna
External Antenna (WK1 option): Maximum of 10 mW (10dBm)
EIRP
Field link wiring distance
Wiring distance between field link and gateway
up to 200m using single twisted shielded pair, 18 AWG.
Physical specifications
Materials of construction
Enclosure
Housing - Low-copper aluminum or stainless steel
Paint - Polyurethane
Cover O-ring - Buna-N
Terminal block and power module
PBT
Antenna
PBT/Polycarbonate (PC) integrated omni-directional antenna
Mounting
Mounting brackets also permit remote mounting. Figure 6 on
page 14.
Weight
Low-copper aluminum:
781 without LCD display - 4.1 lb. (1.9 kg)
781 with M5 LCD display - 4.2 lb. (2.0 kg)
Stainless steel:
781 without LCD display - 8.0 lb. (3.5 kg)
781 with M5 LCD display - 8.1 lb. (3.6 kg)
Enclosure ratings (781)
Housing Style option codes D and E are Type 4X and IP66/67
rated dual-compartment housings.
10
Vibration effect
No effect when tested per the requirements of IEC60770-1
(1999):
High Vibration Level - field or pipeline (10-60 Hz 0.21 mm
displacement peak amplitude / 60-2000 Hz 3g).
Smart Wireless Gateway
August 2014
Model 781 Product Certifications
Approved manufacturing locations
I6
Rosemount Inc. - Chanhassen, Minnesota, USA
Emerson Process Management Asia Pacific Private Limited - Singapore
Telecommunication compliance
All wireless devices require certification to ensure that they adhere to
regulations regarding the use of the RF spectrum. Nearly every country
requires this type of product certification. Emerson is working with
governmental agencies around the world to supply fully compliant
products and remove the risk of violating country directives or laws
governing wireless device usage.
CSA Intrinsically Safe
Certificate Number: 2330424
Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D. Temp
Code T3C
Enclosure Type 4X, IP66/67, when installed per Rosemount
Drawing 00781-1011
European Union Directive information
The EC declaration of conformity for all applicable European directives
for this product can be found on the Rosemount website at
www.rosemount.com. Reference the Quick Start Guides for a hard copy.
FCC and IC
ATEX Directive (94/9/EC)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following conditions: This device may not cause harmful
interference. This device must accept any interference received,
including interference that may cause undesired operation. This device
must be installed to ensure a minimum antenna separation distance of
20 cm from all persons.
Emerson Process Management complies with the ATEX Directive.
Ordinary location certification for FM
As standard, the Gateway has been examined and tested to determine
that the design meets basic electrical, mechanical, and fire protection
requirements by FM, a nationally recognized testing laboratory (NRTL)
as accredited by the Federal Occupational Safety and Health
Administration (OSHA).
North American certifications
I5
FM Intrinsically Safe, Non-Incendive, and Dust Ignition-proof
Certificate Number: 3040398; Intrinsically
Safe for Class I, II, III, Division 1, Groups A, B, C, D, E, F, and
G. Zone Marking: Class I, Zone 0, AEx ia llC; Temperature
Codes T4 (Tamb = -40 to 70 °C); Non-Incendive for Class I,
Division 2, Groups A, B, C, and D. Dust Ignition-proof for
Class II,III, Division 1, Groups E, F, and G. Ambient
temperature limits: -40 to 70 °C; Enclosure Type 4X,
IP66/67, when installed per Rosemount Drawing
00781-1010
Electro magnetic compatibility (EMC) (2004/108/EC)
Emerson Process Management complies with the EMC Directive.
Radio and telecommunications terminal equipment
directive (R&TTE)(1999/5/EC)
Emerson Process Management complies with the R&TTE Directive
European certification
I1
ATEX Intrinsic Safety
Certificate Number: Baseefa11ATEX0059X
II 1G Ex ia IIC T4 Ga (Tamb = -40 °C to 70 °C) Enclosure Type
IP66/67
CE 1180
Input/output parameters
Input/power
Ui = 30 V
Ii = 200 mA
Pi = 1.0 W
Ci = 0
Li = 0
Certification standards
Input/RS485
3600:1998, 3610:2010, 3611:2004, 3810:2005, ANSI/NEMA 250:2003,
ANSI/IEC 60529:2004
Ui = 11 V
Ii = 300 mA
Pi = 1.0 W
Ci = 5.1 nF
Li = 0
Special Conditions of Certification:
1. The Model 781 transmitter housing contains aluminum and is
considered a potential risk of ignition by impact or friction. Care
must be taken into account during installation and use to prevent
impact and friction.
2. The surface resistivity of the unit is greater than one gigaohm. To
avoid electrostatic charge build-up, it must not be rubbed or
cleaned with solvents or a dry cloth.
3. The Model 781 transmitter will not pass the 500Vrms dielectric
strength test and this must be taken into account during
installation.
Output/RS485
Uo = 7.14 V
Io = 112 mA
Po = 1.0 W
Co = 0
Lo = 0
Co = 13.9 F
Lo = 1000 H
11
Smart Wireless Gateway
Special Conditions for Safe Use (X):
1. The plastic antenna may present a potential electrostatic ignition
hazard and must not be rubbed or cleaned with a dry cloth.
2. The Model 781 enclosure is made of aluminum alloy and is given a
protective polyurethane paint finish; however, care should be
taken to protect it from impact or abrasion if located in a Zone 0
environment.
3. The device is not capable of withstanding the 500V isolation test
required by EN 60079-11:2007 Clause 6.3.12. This must be taken
into account when installing the device.
I7
IECEx Intrinsic Safety
Certificate Number: IECEx BAS11.0028X
Ex ia IIC T4 Ga (Tamb = -40 °C to 70 °C)
Enclosure Type IP66/67
Input/output parameters
Input/power
Ui = 30 V
Ii = 200 mA
Pi = 1.0 W
Ci = 0
Li = 0
Input/RS485
Ui = 11 V
Ii = 300 mA
Pi = 1.0 W
Ci = 5.1 nF
Li = 0
Output/RS485
Uo = 7.14 V
Io = 112 mA
Po = 1.0 W
Co = 0
Lo = 0
Co = 13.9 F
Lo = 1000 H
Special Conditions for Safe Use (X):
1. The plastic antenna may present a potential electrostatic ignition
hazard and must not be rubbed or cleaned with a dry cloth.
2. The Model 781 enclosure is made of aluminum alloy and is given a
protective polyurethane paint finish; however, care should be
taken to protect it from impact or abrasion if located in a Zone 0
environment.
3. The device is not capable of withstanding the 500V isolation test
required by IEC 60079-11:2006 Clause 6.3.12. This must be taken
into account when installing the device.
Combination certification
KL
12
Combination of I5, I6, I1, and I7
August 2014
August 2014
Smart Wireless Gateway
Dimensional Drawings
Figure 4. Smart Wireless Gateway
Dimensions are in inches (millimeters).
13
Smart Wireless Gateway
August 2014
Figure 5. Smart Wireless Field Link
Figure 6. Rosemount 781 Transmitter Mounting Configurations with Optional Mounting Bracket
A
C
D
B
A. Pipe mounting
B. 6.20 (158)
C. 2-in U-bolt for pipe mounting
D. 1-in U-bolt for transmitter mounting
Dimensions are in inches (millimeters).
14
August 2014
Smart Wireless Gateway
15
Smart Wireless Gateway 1410
Product Data Sheet
00813-0300-4410, Rev AB
August 2014
Emerson Process Management
Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN 55317 USA
T (U.S.) 1-800-999-9307
T (International) (952) 906-8888
F (952) 906-8809
www.rosemount.com
Emerson Process Management
Blegistrasse 23
P.O. Box 1046
CH 6341 Baar
Switzerland
T +41 (0) 41 768 6111
F +41 (0) 41 768 6300
www.rosemount.com
Emerson Process Management
Asia Pacific Pte Ltd
1 Pandan Crescent
Singapore 128461
T +65 6777 8211
F +65 6777 0947
Service Support Hotline: +65 6770 8711
Emerson Process Management
Latin America
1300 Concord Terrace, Suite 400
Sunrise, Florida 33323 USA
Tel + 1 954 846 5030
www.rosemount.com
Email: Enquiries@AP.EmersonProcess.com
www.rosemount.com
Standard Terms and Conditions of Sale can be found at www.rosemount.com\terms_of_sale
The Emerson logo is a trade mark and service mark of Emerson Electric Co.
AMS, Rosemount, and the Rosemount logotype are registered trademarks of Rosemount Inc.
PlantWeb is a registered trademark of one of the Emerson Process Management group of companies.
HART and WirelessHART are registered trademarks of the HART Communication Foundation
Modbus is a registered trademark of Modicon, Inc.
All other marks are the property of their respective owners.
© 2014 Rosemount Inc. All rights reserved.
Download PDF