Creda | C150 | User guide | Creda C150 User guide

HOW TO USE YOUR SPA200 SHOWER (SUMMARY)
1. Ensure the electricity and water are turned on to the unit.
2. Press the start / stop button “B”.
This will turn the shower on, the water will flow and the
indicator lights will glow showing chosen Power Selection.
We recommended that you do not enter the water spray
during this period, even if the shower has just been used.
3. Knob “A” controls the power selection.
Select “High”, “Med (medium)” or “Cold”
4. If the water is not at your desired showering
temperature, turn knob “C” a small amount until
you reach the desired showering temperature.
Turn clockwise (follow blue arrows) for cooler.
Turn anti-clockwise (follow red arrows) for warmer.
As a helpful guide the knob position is indicated by a number being displayed in Window “D”.
On the scale “1” is the coolest, whilst “9” is the hottest.
5. When you have finished showering, press the start / stop button “B” again.
6. Water will continue to flow for up to 7 seconds before switching off.
This reduces the temperature of the water in the tank for the next user.
The indicator lights will go out.
7. Wait for the water to stop, switch off the electricity supply at the ceiling switch or local isolator.
Notes
•
Wait 20 seconds for the temperature to stabilise after each adjustment.
•
The indicator lights illuminate when the heaters are on and, if the shower has been
recently used, they may take up to 20 seconds to come on.
During this time the water may go from very hot to cold before stabilising.
•
The position of knob “C” will be approximately the same each time the shower is
used, varying only with incoming water temperature or pressure changes
(e.g. you will only need to change from summer to winter).
•
During normal operation, if an overheated water temperature is sensed then the
heater will switch off and the “Overheat” light will illuminate.
Water will continue to flow and cool down before the heater switches back on again.
IMPORTANT WARNINGS!
DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT IT OF BEING FROZEN.
WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
DO NOT OPERATE THE APPLIANCE IF WATER DISCHARGES FROM THE PRESSURE RELIEF
VALVE. MAINTENANCE IS REQUIRED BEFORE THE APPLIANCE CAN BE SAFELY USED.
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN AND
THE INFIRM) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES, OR LACK OF
EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR
INSTRUCTION CONCERNING USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY
DO NOT PLAY WITH THE APPLIANCE.
We offer a technical advisory service on the telephone: RING 0844 372 7766 (UK ONLY)
12
(A4) Leaflet No. 555-2138-61b
CREDA SPA200
SMART TECHNOLOGY
ELECTRIC SHOWER
Installation and User Guide
IMPORTANT:
This booklet should be left with the user after
installation and demonstration
:
GUARANTEE AND CONTACT DETAILS
CONTENTS
Section
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Information . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to install your SPA200 Shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to maintain your SPA200 Shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to use your SPA200 Shower (Detailed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What to do if things go wrong (1) Self Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional Accessories and Common Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What to do if things go wrong (2) Professional Service . . . . . . . . . . . . . . . . . . . . . . . . .
Creda After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How your SPA200 Shower Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guarantee and Contact Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to use your SPA200 Shower (Summary) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
2
2
3
6
7
8
8
9
9
10
11
12
INTRODUCTION
Thank you for purchasing a quality Creda SPA200 Shower manufactured in England.
To enjoy your new shower at its best, please take time to read this manual thoroughly to
familiarise yourself with all instructions, BEFORE beginning installation.
The Creda SPA200 is an electric shower incorporating our “Smart Technology” with a
“Set and Forget” function of a push-button start/stop facility which starts the shower at a pre-set
power and flow rate reducing the amount of adjustment required.
Your shower is designed to stabilise temperature changes caused by water pressure fluctuations.
These can result from toilets being flushed or taps being turned on and off.
When this happens your showering temperature will be held within a controlled band, provided that
the minimum pressure required by the shower is maintained (see “Effect of Other Water Devices”).
If you experience any difficulty with the installation or operation of your new
shower, then please refer to the “What to do if things go wrong” section in this
manual before contacting us.
IMPORTANT SAFETY INFORMATION
1. Your shower has been designed for convenience, economy and safety of use, provided that it is
installed, used and maintained in good working order and in accordance with our instructions and
recommendations.
2. All wiring and installation must be supervised by a suitably qualified person.
3. THIS APPLIANCE MUST BE EARTHED.
4. The installation must be in accordance with the current edition of BS.7671 (the “IEE Wiring
Regulations”) and “Part P” of the “Building Regulations” in force at the time of installation.
Installations outside England and Wales must also conform to any local regulations in effect.
This appliance is intended to be permanently connected to the fixed electrical wiring of the mains
supply with its own dedicated supply.
5. This appliance must NOT be fitted where it may be subjected to freezing conditions
6. DO NOT switch the appliance on if you suspect it of being frozen.
Wait until you are sure it has thawed out.
7. DO NOT fit any sort of tap or control on the appliance outlet. The appliance is designed to have
an open outlet and should only be used with “Creda” recommended fittings.
8. Take care to avoid restricting the outlet of the pressure relief device. If water is discharged from
the pressure relief device, maintenance will be required before the appliance can be safely used.
9. Isolate the mains electrical and water supply before removing the front cover of the appliance.
2
Full details of terms and conditions are available on request from:-
APPLIED ENERGY PRODUCTS LIMITED
MORLEY WAY, PETERBOROUGH PE2 9JJ
TEL: +44 (0) 844 372 7761
FAX: +44 (0) 844 372 7762
Website: www.applied-energy.com
11
HOW YOUR SPA200 SHOWER WORKS
HOW TO INSTALL YOUR SPA200 SHOWER
1. Water is heated instantaneously as it flows over the
heating elements in the copper cylinder (Diagram 8).
WARNING: ALL WIRING AND INSTALLATION MUST BE
SUPERVISED BY A SUITABLY QUALIFIED PERSON.
2. The heaters are only switched on when sufficient
water is flowing.
This is done automatically with a switch which works
on water pressure and is indicated by 2 or 3 lights
illuminating depending on knob “A” power selection.
WARNING: DO NOT INSTALL THIS SHOWER WHERE IT MAY BE
SUBJECTED TO FREEZING CONDITIONS
3. The water is turned on and off by the solenoid valve
built into the shower.
This is switched on when button “B” is pressed.
4. The flow of water is automatically held at the level set
by the user even though the supply pressure may
vary (see “Effect of Other Water Devices on Incoming
Water Supply”).
5. If the water supply falls below a set limit, the pressure
switch will operate and switch off the power to the
elements. This is indicated by the middle power indication lights flickering and going out (see
“Effect of Other Water Devices on Incoming Water Supply”).
6. As a further safeguard, a thermal cut-out switches the power off if the water temperature
climbs above the set limit and the “Overheat” light will illuminate.
This cut-out, which gives an audible click, may also operate due to residual heat when the shower
is switched off. It will reset itself if water is run through the shower for 10 to 20 seconds, and
the “Overheat” light will go out.
7. The pressure relief device is to safeguard against abnormal pressure conditions, and provides a
level of appliance protection should an excessive build of pressure occur within the shower.
We recommend that the installation is done in the following sequence.
a. Fixing the shower to the wall
b. Plumbing c. Electrical connections
a. FIXING THE SHOWER TO THE WALL
1. Position the riser rail at a convenient height for majority of users as
detailed in Diagram 1 and mark its position (also see separate
accessories fitting instructions).
2. Position the heater so that the top of the unit is horizontal and level
with, or a maximum of 0.6 metres (2ft) below the top of the
riser rail. Choose a flat piece of wall to avoid the possibility of
distorting the backplate thus making the front cover a poor fit.
3. Adjust the position to get the most convenient arrangement taking
the following into account.
•
The heater must not be mounted in the direct spray from the handset.
•
The handset must not be able to come into contact with used water in the cubicle, bath or
basin. If it can, even after the hose has been retained by the retaining ring (see separate
accessories fitting instructions sheet), a vacuum breaker must be fitted (available from us).
4. Fix the riser rail with screws provided (see separate instructions supplied with accessories).
Effect of Seasonal Incoming Water Temperature Changes
The required water temperature is achieved by adjusting the rate of water flow.
Diagram 9 shows the principle involved in relating temperature rise to flow rate.
The higher the water rate the lower the temperature and vice versa.
The temperature of the water supplied from the mains can vary considerably
throughout the year from 5 to 20°C.
This means that in the winter, flow rate will be less than in the summer to
achieve the same outlet temperature.
In summer the “Med (medium)” power setting may give adequate hot water.
In some winter conditions, it may be necessary to select the inner or outer spray pattern only of
your shower handset. This will ensure correct operation of the shower with a slightly lower flow rate.
Effect of Other Water Devices on Incoming Water Supply
Your shower is designed to stabilise temperature changes caused by water pressure
fluctuations. These can result from toilets being flushed or taps being turned on and off.
When this happens your showering temperature will be held within a controlled band, provided that
the minimum pressure required by the shower is maintained.
5. Decide the position of the electrical cable into the unit. If top or bottom entry is chosen
(according to Diagram 7 on page 9), cut away the walls in the backplate as shown in Diagram 2.
Your shower requires a minimum running pressure of 69kPa (0.7 bar, 10 psi).
At pressures above 69kPa (0.7 bar, 10 psi) it will minimise temperature fluctuations as detailed
above. If the water pressure falls below 69kPa (0.7 bar, 10 psi) it is likely that the pressure switch
will turn off the power to the heating elements, resulting in a cold shower.
This will be indicated by the middle power setting indication lights flickering and going out.
6. Decide the position of entry of the cold water pipe into the unit.
If top, cut away the backplate.
If rear, please read the section on plumbing.
If bottom, remove the front cover (complete with knobs) and cut away the detachable corner
section as shown.
10
3
7. If you have not yet done so, remove the front cover assembly by undoing the retaining screws at
the top and bottom of the unit and lifting the cover off.
Your shower is provided with 2 fixing positions in the backplate (see Diagram 7 on page 9).
The top-fixing hole is a “key-hole” slot (another key-hole is provided for alternate fixing), and
should be marked and drilled first.
Tighten top screw with head protruding about 10mm from the wall and hook the backplate over
the screw head. This allows for correct and accurate alignment of your shower before marking
and fixing the bottom position.
You may not wish to tighten up both screws at this stage as the holes are elongated to allow for
adjustment after other connections have taken place.
b. PLUMBING
WARNING: ENSURE THAT THE MAINS WATER SUPPLY MEETS THE REQUIREMENTS
BELOW BEFORE CONTINUING WITH INSTALLATION.
WHAT TO DO IF THINGS GO WRONG (2)
PROFESSIONAL SERVICE
If the previous “Self Help” checks fail to restore the performance, you should seek professional help.
The person who installed the shower is probably the best one to investigate and correct it and is
certainly the person to contact if you have had a problem in the guarantee period.
The following additional checklist is provided for the benefit of the qualified service person.
WARNING: SWITCH OFF THE ELECTRICITY AT THE LOCAL ISOLATOR
BEFORE REMOVING THE COVER TO MAKE CHECKS
Water too HOT
Water flow restricted by blockage in filter of solenoid valve.
Switch off water, loosen inlet connection to solenoid, remove filter in solenoid
with long nosed pliers and flush clean.
Water too COLD
Check circuit through thermal cut-out.
Check circuit through microswitches on the pressure switch.
Check each element circuit.
Check operation of relay.
Check tightness of electrical connections.
Check Numbered Dial is correctly engaged into Control Knob (see Diagram 5)
Undo headworks of stabiliser valve.
Check stabiliser is in place and remove any debris in valve.
The heater must be connected to the mains cold water supply.
This must have a minimum running pressure of 69kPa (0.7 bar, 10 psi)
and a maximum pressure of 690kPa (7.0 bar, 100 psi).
WARNING: BEFORE CONNECTING THE PIPE WORK TO THE SHOWER,
ENSURE THAT THE PIPE WORK IS FULLY FLUSHED OUT.
1. Unscrew the “Red Cap” from the shower outlet pipe and discard it in a suitable manner.
This has been used to seal the shower during transit, and is no longer required.
2. It is recommended that a WRAS (Water Regulations Advisory Scheme) listed isolating valve is
fitted to the incoming mains cold water before the shower unit.
This will allow the unit to be serviced or exchanged without having to turn off the water at the
water stop valve.
3. The heater can be fed from a header tank provided this has a minimum head of 7 metres (23ft).
No control over
water flow
Water discharges
from pressure
relief valve
Check for cause of high pressure and remove it.
Blockage on outlet e.g. blocked shower handset.
Replace the pressure relief disc (not covered by guarantee).
Water does not
flow when button
“B” is pressed.
Check circuit through solenoid coil. If defective then replace.
Check circuit through microswitches. If defective then replace.
Check circuit through shutdown PCB. If defective then replace.
Power supply not reaching shower.
4. Ø15mm copper or stainless steel pipe should be used.
To avoid cross threading, DO NOT REMOVE the nut from the elbow when positioning the pipe.
If top entry is required, turn the elbow 180° into the required position.
If rear entry is required, treat as top entry with an additional “Yorkshire” elbow (soldered type)
for fitting into the rear channel.
In multiple installations, correct pipe work sizes should be calculated to maintain adequate flow
to each shower.
We offer a technical advisory service on the telephone to installers
and other customers with problems in the field.
5. It is permissible to use a WRAS (Water Regulations Advisory Scheme) approved sealant sparingly
whilst avoiding excess finding its way into the shower operating parts.
Some spare parts (see later section) can be supplied
against Credit or Debit cards.
6. With isolating valve connected, flush the pipe work through to remove any particles etc,
before making the final connection to the shower.
Blockage in the water ways (particularly the handset and solenoid valve) will prevent the heater
working properly. Note: You may be charged for a service call if it is due to incorrect installation.
7. The shower is designed to have an open outlet and should only be used with “Creda”
recommended fittings.
Do not connect the handset until after the shower front cover and corner section are fitted.
WARNING: DO NOT FIT A TAP ON THE SHOWER OUTLET.
WARNING: TAKE CARE TO AVOID RESTRICTING THE OUTLET OF THE
PRESSURE RELIEF DEVICE
4
CREDA AFTER SALES SERVICE
RING 0844 372 7766 (UK ONLY)
RING YOUR LOCAL DEALER (Export Variants)
RING 0844 372 7750 (UK ONLY)
Remember to quote the exact type of shower, as written on the
front of the shower and on this leaflet.
The model and serial number are located on the bottom face of
the shower.
Make a note of those numbers here, and be sure to quote them if
you call for advice.
Model Number: 53-67_ _ _ _ _ _ _ _ _ _ _ _ _
Serial Number: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Note: You may be charged for a service call
if you do not have the serial number.
9
WHAT TO DO IF THINGS GO WRONG (1)
WARNING: THIS SHOWER MUST BE EARTHED.
SELF HELP
If the shower is not working satisfactorily, make the following checks before calling out the installer.
Any one of these adjustments could restore the performance.
The shower cycles
The shower temperature is set too hot causing the thermal cut-out (safety
from HOT to COLD device) to operate.
Turn knob “C” clockwise (following the “blue arrows”) to increase water flow.
Slowly increase the water temperature by turning knob “C” anti-clockwise
following the “red arrows” until a comfortable showering temperature has been
reached.
You MUST WAIT approximately 20 seconds for each adjustment to affect the
water temperature.
“Med (medium)” setting may need to be selected.
Water too HOT
Water too COLD
Spray pattern poor
Water takes longer
to heat up
Water goes cold
while using
shower
Water continues to
flow when
button “B” pressed
Broken parts
c) ELECTRICAL
Increase water flow by adjusting knob “C” clockwise (following the “blue
arrows”).
“Med (medium)” setting may need to be selected.
Increase pressure to water supply e.g. fully open service valve or stop cock.
Check hose is not kinked restricting the water flow.
Clean shower handset.
Check power is on by neon being illuminated.
Decrease water flow by adjusting Knob “C” anti-clockwise (following the “red
arrows”).
“High” setting may need to be selected.
Select inner or outer only handset spray pattern.
Clean the shower handset.
Thermal cut-out has operated after previous use (“Overheat” light is on)
(automatically resets when unit cools down)
“High” setting may need to be selected.
Check neon light is on.
Check water pressure has not fallen so far as to let pressure switch cut out,
e.g. Another tap drawing water off.
Raise position of shower handset.
This is normal.
The shower includes a shutdown feature that means the water will continue to
flow for up to 7 seconds after button “B” has been pressed to stop the shower.
Please contact our spares department on 0844 372 7750 (UK only).
Fitting instructions are provided with most spares
ADDITIONAL ACCESSORIES
The electrical installation must be in accordance with the current BS.7671 (IEE Wiring Regulations)
and “Part P” of the Building Regulations and/or local regulations
1. The shower unit is designed for a single phase AC electrical supply.
Please check the rating plate on the unit to see what details apply to your shower.
AS A GUIDE ONLY (* Only applies if external earth impedance is less than 0.35 Ohms)
Rating
7.2 / 6.6kW 240 / 230V
8.5 / 7.8kW 240 / 230V
9.5 / 8.7kW 240 / 230V
10.5 / 9.6kW 240 / 230V
Fuse / MCB
Cable Sizes
4.0mm²
6.0mm²
6.0mm²
10.0mm²
6.0mm²
10.0mm²
6.0mm²
10.0mm²
6.0mm²
10.0mm²
6.0mm²
10.0mm²
32A Type B MCB
40A Type B MCB
40A Type B MCB
45A BS.1361 fuse
40A Type B MCB
45A BS.1361 fuse
10.0mm²
45A BS.1361 fuse
Additional accessories and spare parts can be
supplied against any Credit or Debit cards
from Creda Sales Hotline 0844 372 7750
8
12m Max.*
Remember to upgrade the cable if it runs in thermal insulation in a loft, or for a longer distance.
2. A means for disconnection in all poles must be incorporated in the fixed wiring in accordance
with the wiring rules.
We recommend a ceiling switch mounted in a convenient position.
3. Cut back cable as in Diagram 3. Connect cable to terminal block making sure that all the
retaining screws are VERY TIGHT and that no cable insulation is trapped under the screws.
WARNING: FAILURE TO COMPLY WITH THESE
INSTRUCTIONS COULD RESULT IN
FAILURE OF THE TERMINAL BLOCK
4. Re-Fit the corner section back into the backplate.
COMMON SPARE PARTS
Please Note:- The fitting of Spare Parts must be
White 2 metre Shower Hose
Cat No. 83792578
Chrome 1.25m Shower Hose
Cat No. 93797641
Chrome Standard Accessories
Cat No. 83595317
Chrome Multi-Mode Accessories
Cat No. 83595318
Chrome Curved Accessories
Cat No. 83595320
Curtain and Rail Pack
Cat No. 83792812
Curtain and Rail Pack with
Non-Slip Mat
Cat No. 83792811
WRAS listed Water Isolating Valve Cat No. 93792452
Cable Length
21m Max.
35m Max.
27m Max.
45m Max.
27m Max.
45m Max.
12m Max.*
21m Max.*
27m Max.
45m Max.
12m Max.*
21m Max.*
supervised by a suitably qualified person.
Front Cover (White)
Cat No. 93550812
Tank-Base Assy (7.2kW)
Cat No. 93597848
Tank-Base Assy (8.5kW+)
Cat No. 93597849
Solenoid Valve
Cat No. 93590722
Cam and Adaptor Kit
Cat No. 93590793
Tank Clip
Cat No. 93768309
PRV Washer
Cat No. 93795817
Cylinder “O”-Ring
Cat No. 93795809
Thermal Cut-Out 50/88°C
Cat No. 93597836
Phased Shut-Down PCB
Cat No. 93597813
Phased Shut-Down Relay
Cat No. 93597862
Handset
Cat No. 93597861
Chrome Shower Hose 1.25m Cat No. 93797641
5
5.
Re-Fit the front cover (see Diagram 5), and secure by replacing the top and bottom fastening screws.
Ensure knob “A” is aligned to the “High” position.
Ensure knob “C” is aligned to “12 o’clock.
In the main body of the shower, turn the “Camshaft” as shown.
In the main body of the shower, turn the “Numbered Dial” fully clockwise until it is at the position
shown. Note:- this instruction should be used if the “Drive Dial” becomes accidentally dislodged.
e. Fit the front cover of the shower to the main body.
Ensuring that the knobs correctly engaged to their mating component.
f. Check that knob “A” has been correctly aligned by ensuring that all 3 power settings can be selected.
g. Check that knob “C” has been correctly aligned by turning anti-clockwise and ensuring that knob turns
approximately 1 full turn and when turned back fully clockwise, returns to “12 o’clock”.
a.
b.
c.
d.
HOW TO USE YOUR SPA200 SHOWER (DETAILED)
1.
Ensure the electricity and water are turned on to the unit.
2.
Your shower has 2 control knobs (see Diagram 6).
Knob “A” controls the 3 power settings.
The most popular is “High”.
There are also options for a “Med (medium)”
or “Cold” shower (see notes 8 and 9).
Knob “C” controls the temperature of the water, and as a
helpful guide the knob position is indicated by a number
being displayed in Window “D”.
On the scale “1” is the coolest, whilst “9” is the hottest.
For this example turn knob “A” to “High”
and set knob “C” to display number “5”.
3.
Press button “B”. The water will flow and 3 lights will illuminate
to indicate that the selected power rating is “High” (indicated by “High” next to the Indicator Lights).
4.
Allow about 20 seconds for the temperature of the water to stabilise. It is recommended that you do
not wholly enter the water spray during this period, even if the shower has just been used.
IF WATER IS TOO COLD
Turn knob “C” anti-clockwise in the
direction of the “red arrows” until the next
number is displayed in Window “D” and
continue turning anti-clockwise until you
get the water temperature of your liking.
Wait 20 seconds after each adjustment
for the water temperature to stabilise.
6.
7.
Fit the shower hose, and operate the shower first without the handset to flush out particles,
fit the handset and then operate the shower as on page 7 or 12 and check:
a. That the water gets to a satisfactory temperature and water flow can be adjusted by control knob “C”.
b. Power selection operates in all 3 positions, giving a change in water temperature and that the power
indictor lights functions correctly.
c. Check again for leaks
d. That the holes in the shower handset are not blocked
The final adjustment may be anywhere on
the scale, even between numbers.
If after turning fully anti-clockwise water is
still too cold, set shower pattern on shower
handset to outer or inner pattern only.
It is recommended that the shower unit and hose etc. be cleaned using a soft cloth and that the use of
abrasive or solvent based cleaning fluid be avoided, especially on any plated finishes.
We recommend that before any cleaning, the isolating switch be turned off, thus avoiding accidentally
switching on the shower.
WARNING: YOU MUST REGULARLY INSPECT THE SHOWER HOSE FOR WEAR AND DAMAGE.
REPLACE IF NECESSARY, OR EVERY TWO YEARS, WITH OUR APPROVED PART.
Wait 20 seconds after each adjustment for the water
temperature to stabilise.
The final adjustment may be anywhere on the scale,
even between numbers.
If after turning fully clockwise, water is still too hot,
adjust knob “A” to “Med (medium)” setting and
re-adjust as above.
Water flow will be reduced on this setting.
5.
Once a temperature setting to your liking has been achieved, knob “C” will rarely need adjusting. You
must however take into account required adjustments for variations of incoming mains water temperature
between summer and winter (see “Effect of Seasonal Incoming Water Temperature Changes” page 10).
6.
When you have finished showering, press button “B” only (the “Med (medium)” light will go out).
Water will continue to flow for up to 7 seconds before switching off.
This reduces the temperature of the water in the tank for the next user.
Wait for the water to stop, and then switch off the electricity at the ceiling switch or local isolator.
7.
The “Med (medium)” setting of knob “A” reduces the power used by the shower giving a cooler shower or
the option of reduced water flow. This option is mainly for summer usage and if this is used then knob
“C” must be re-adjusted. On this setting 2 lights will illuminate.
DEMONSTRATE OPERATION TO USERS
HOW TO MAINTAIN YOUR SPA200 SHOWER
IF WATER IS TOO HOT
Turn knob “C” clockwise in the direction of the
“blue arrows” until the next number is displayed in
Window “D” and continue turning clockwise until you
get the water temperature of your liking.
8.
The “Cold” setting of knob “A” will supply water without any heating, and 1 light will illuminate.
WARNING: IN ORDER TO MAINTAIN THE PERFORMANCE OF YOUR SHOWER,
YOU MUST CLEAN THE SHOWER HANDSET REGULARLY
9.
Your shower is designed to stabilise temperature changes caused by water pressure fluctuations (see
“Effect of Other Water Devices on Incoming Water Supply” page 10).
All water contains particles of lime-scale, which build up in the shower handset and
unit reducing the performance.
It is therefore important to clean the shower handset by simply rubbing the rubber
nozzles, or soaking in a proprietary lime-scale remover and rinsing thoroughly before use.
NOTE: After use it is normal for some water to drip from the shower handset for a
few moments. This inhibits lime-scale build-up over prolonged use.
WARNING: DO NOT SWITCH THE SHOWER ON IF YOU SUSPECT IT OF BEING FROZEN.
WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.
6
WARNING: DO NOT OPERATE THE SHOWER IF WATER IS DISCHARGED FROM THE PRESSURE RELIEF
VALVE. MAINTENANCE IS REQUIRED BEFORE THE SHOWER CAN BE USED.
WARNING: CONSIDERATION SHOULD BE GIVEN TO SUPERVISING THE YOUNG, ELDERLY AND THE
INFIRM WHILST THEY USE THIS SHOWER.
7
Download PDF