Duerkopp Adler | 211 | Operating instructions | Duerkopp Adler 211 Operating instructions

510
CNC automat for bartacking seams
and short seams
Operating Instructions
1
Installation Instructions
2
Service Instructions
3
Postfach 17 03 51, D-33703 Bielefeld Ÿ Potsdamer Straße 190, D-33719 Bielefeld
Telefon +49 (0) 5 21/ 59 25-00 Ÿ Telefax +49 (0) 5 21/ 9 25 24 35 Ÿ www.duerkopp-adler.com
Ausgabe / Edition:
02/2006
Printed in Federal Republic of Germany
Teile-Nr.:/Part-No.: 0791 510001
Summary
Operating Instructions
Installation Instructions
Service Instructions
Interconnection-diagram
9890 510001 B
Foreword
This instruction manual is intended to help the user to become familiar
with the machine and take advantage of its application possibilities in
accordance with the recommendations.
The instruction manual contains important information on how to
operate the machine securely, properly and economically. Observation
of the instructions eliminates danger, reduces costs for repair and
down-times, and increases the reliability and life of the machine.
The instruction manual is intended to complement existing national
accident prevention and environment protection regulations.
The instruction manual must always be available at the
machine/sewing unit.
The instruction manual must be read and applied by any person that is
authorized to work on the machine/sewing unit. This means:
–
–
–
Operation, including equipping, troubleshooting during the work
cycle, removing of fabric waste,
Service (maintenance, inspection, repair and/or
Transport.
The user also has to assure that only authorized personnel work on
the machine.
The user is obliged to check the machine at least once per shift for
apparent damages and to immediatly report any changes (including
the performance in service), which impair the safety.
The user company must ensure that the machine is only operated in
perfect working order.
Never remove or disable any safety devices.
If safety devices need to be removed for equipping, repairing or
maintaining, the safety devices must be
remounted directly after completion of the maintenance and repair
work.
Unauthorized modification of the machine rules out liability of the
manufacturer for damage resulting from this.
Observe all safety and danger recommendations on the machine/unit!
The yellow-and-black striped surfaces designate permanend danger
areas, eg danger of squashing, cutting, shearing or collision.
Besides the recommendations in this instruction manual also observe
the general safety and accident prevention regulations!
General safety instructions
The non-observance of the following safety instructions can cause
bodily injuries or damages to the machine.
1. The machine must only be commissioned in full knowledge of the
instruction book and operated by persons with appropriate
training.
2. Before putting into service also read the safety rules and
instructions of the motor supplier.
3. The machine must be used only for the purpose intended. Use of
the machine without the safety devices is not permitted. Observe
all the relevant safety regulations.
4. When gauge parts are exchanged (e.g. needle, presser foot,
needle plate, feed dog and bobbin) when threading, when the
workplace is left, and during service work, the machine must be
disconnected from the mains by switching off the master switch or
disconnecting the mains plug.
5. Daily servicing work must be carried out only by appropriately
trained persons.
6. Repairs, conversion and special maintenance work must only be
carried out by technicians or persons with appropriate training.
7. For service or repair work on pneumatic systems, disconnect the
machine from the compressed air supply system (max. 7-10 bar).
Before disconnecting, reduce the pressure of the maintenance
unit.
Exceptions to this are only adjustments and functions checks
made by appropriately trained technicians.
8. Work on the electrical equipment must be carried out only by
electricians or appropriately trained persons.
9. Work on parts and systems under electric current is not permitted,
except as specified in regulations DIN VDE 0105.
10. Conversion or changes to the machine must be authorized by us
and made only in adherence to all safety regulations.
11. For repairs, only replacement parts approved by us must be used.
12. Commissioning of the sewing head is prohibited until such time
as the entire sewing unit is found to comply with EC directives.
It is absolutely necessary to respect
the safety instructions marked by these signs.
Danger of bodily injuries !
Please note also the general safety instructions.
Index
Page:
Preface and general safety hints
Part 1: Operating Instructions cl. 510
1.
Description of product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
2.
Description of proper use
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
3.
Subclasses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
4.
Optional equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
5.
Stands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6.
6.1
Technical data
Technical data of the subclasses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
7.
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
Operating
Threading needle thread. . .
Adjust needle thread tension
Open needle thread tension
Adjust thread regulator . . . .
Wind on bobbin thread . . . .
Change hook thread bobbin .
Adjust bobbin thread tension
Change needle . . . . . . . .
8.
8.1
8.1.1
8.2
8.2.1
8.3
8.3.1
8.3.2
8.3.3
8.4
8.5
8.5.1
8.5.2
Operating the control of cl. 510
The control panel . . . . . . . . . .
The keys . . . . . . . . . . . . . . .
User interface . . . . . . . . . . . .
Structure of menu . . . . . . . . . .
Alter numerical values, parameter
Alter numerical values . . . . . . .
Selection of a parameter . . . . . .
Selection of alternatives . . . . . .
Seam patterns . . . . . . . . . . . .
Main menu . . . . . . . . . . . . . .
Seam pattern operation . . . . . .
Programming mode . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . .
. . . . .
. . . . .
. . . . .
values,
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
. . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . .
. . . . . .
. . . . . .
. . . . . .
selection
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
9
10
10
11
12
13
14
15
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
of alternatives
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
16
16
18
18
19
19
20
20
21
22
22
27
1
Index
Page:
8.5.3
8.5.3.1
8.5.3.2
8.5.4
8.5.4.1
8.5.4.2
8.5.4.3
8.5.4.4
8.5.4.5
8.6
8.6.1
8.6.2
8.6.3
Seam pattern sequences . . . . . . . . . . . . . . . .
Switching the sequence programming mode on/off
Sequence programming mode . . . . . . . . . . . . .
Technician mode . . . . . . . . . . . . . . . . . . . . .
Machine configuration . . . . . . . . . . . . . . . . . .
User configurations . . . . . . . . . . . . . . . . . . . .
Service functions . . . . . . . . . . . . . . . . . . . . .
Free contours . . . . . . . . . . . . . . . . . . . . . . .
Memory dongle . . . . . . . . . . . . . . . . . . . . . .
Error messages . . . . . . . . . . . . . . . . . . . . . .
Error categories . . . . . . . . . . . . . . . . . . . . . .
Application messages . . . . . . . . . . . . . . . . . .
Machine faults (DACIII) . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
29
29
32
32
36
45
49
63
71
78
78
79
81
9.
Sewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
10.
10.1
10.2
Maintenance
Cleaning and checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
88
89
11.
Standard seam patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
12.
Clamping feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
97
13.
Numbering of menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
98
1.
Description of product
The Dürkopp Adler 510 is a CNC automate for bartacking seams and
short seams. The available standard bartacks are size-adjustable and
can additionally be memorized in this modified shape.
Free seam contours can be programmed directly at the control panel
without any further devices.
Technical features
– DAC control with control panel.
The following functions are available:
– 50 standard bartacks.
These bartacks can temporarily be modified as regards length,
width and speed. When switching off the automate the
modified values of the bartack sewn last are maintained.
– 40 modified bartacks can be memorized in addition.
– 9 free seam contours with a total of 5000 available stitches
can additionally be memorized.
So it is possible to attach e.g. small appliqués.
The coordinates are entered at the control panel. No further
devices are required.
– 25 seam pattern sequence programs with up to 20 seam
patterns per seam pattern sequence program can be created
and memorized.
– The coordinates are entered with a precision of 0.1 mm.
– In case of a rectangular contour of the fabric clamping feet the
modification of bartacks is automatically checked in order to
avoid a collision of needle and fabric clamping feet.
– Counter of capacity and daily number of pieces.
– Bartacks and/or seam pattern sequence programs and/or the
modification of special bartacks can be blocked.
– The speed can be changed from 0 rpm (manual operation with
full operability of the x-y drive) up to 2700 rpm in
steps of 100 rpm.
– Fabric drive via two step motors.
– Drive of the automatic bartacker directly at the arm shaft via
brushless direct current motor.
– Maximum sewing field size 40 x 20 mm.
– Oil wick lubrication of arm shaft and driving shaft with two oil
reservoirs.
– Service and maintenance work is supported by comprehensive test
programs.
5
1
2.
Description of proper use
Class 510 is an automatic bartacker determined for processing light to
medium-weight material, i.e. fabrics made of textile fibres or leather.
Such sewing materials are used in the clothing industry and for the
production of home and car upholstery.
Furthermore, this automatic bartacker can also sew so-called technical
seams. However, in this case the user has to estimate the possible
risks (preferably in cooperation with DÜRKOPP ADLER AG) because
on the one hand such fields of application are comparatively rare and
on the other hand there is an immense variety of possibilities.
According to the result of this estimation suitable safety measures may
have to be taken.
Generally only dry fabrics must be processed on this automatic
bartacker. The material must not be thicker than 10 mm when
compressed by the lowered sewing feet. It must not include any hard
objects as otherwise the operator would have to wear an eye
protection when working with the automate. Such an eye protection
cannot be delivered at present.
In general the seam is produced with sewing threads made of textile
fibres (cotton threads, synthetic threads or core threads) with the
following dimensions:
Class 510-211/212
threads of the dimension 50/3 - 120/3
Class 510-213
threads of the dimension 30/3 - 120/3
If other threads are to be used, it is indispensable also in this case to
consider the possible risks and to take corresponding safety
measures, if necessary.
This automatic bartacker must only be installed and operated in dry
and well-kept rooms. In case it is operated in other rooms which are
not dry and well-kept further measures can become necessary which
have to be agreed upon (see EN 60204-31: 1999).
We as manufacturers of industrial sewing machines take it for granted
that at least semi-skilled operators are working with our products so
that we can assume that all usual operations and their risks are known
to them.
3.
Subclasses
Cl. 510-211
Automatic single needle lockstitch bartacker with thread trimmer and
thread wiper.
Equipped with a special sewing equipment for general bartacking
operations in outer garments.
Cl. 510-212
Automatic single needle lockstitch bartacker with thread trimmer and
thread wiper.
Equipped with a contraction clamp especially for bartacking of
double-chainstitch buttonholes.
Cl. 510-213
Automatic single needle lockstitch bartacker with thread trimmer and
thread wiper.
Equipped with a special sewing equipment for particularly thick fabrics.
Field of application:
General bartacking operations, e.g. bartacking of loops, pockets or fly
pieces in jeans or working clothes.
6
4.
Optional equipment
The following optional equipment is available for the automatic
bartacker 510:
Order No.
Optional equipment
see Spare Parts List
Special clamping foot set (optional/special manufacture, APC) ”
0510 59 004 4
Laser marking light (3 lights)
0510 59 003 4
Additional laser light
0510 59 005 4
Push button
9822 51 002 6
Sewing light
9822 51 002 7
Table clamp
9870 00 102 1
Cable assembly (add-on kit socket for sewing light)
0510 59 006 4
Pneumatic sewing foot lifting (510-211, -213)
0510 59 009 4
Conversion kit class 510-211 into -213
0510 59 010 4
Electric thread wiper (510-211, -213)
0510 15 001 4
“Large capacity hook”; conversion kit class 510-213 into -214
1
Further optional equipments are available. Please contact our application centre (APC).
E-mail: marketing@duerkopp-adler.com
5.
Stands
The following stand is available for the automatic bartacker 510:
MG55 40 029 4
6.
Stand package
Table top size
Stand height
600 x 1060 mm
1160 to 1305 mm
Technical data
Noise:
Lc = 78dB(A
Emission value per work place according to DIN 45635-48-A-1-KL-2
Bartack length:
Stitch/Bartack:
Throw width:
Speed:
Fabric:
Sewing cycle:
15 mm
28
2.5 mm
2700 min -1
G1 DIN 23328 two-ply
1.3 sec on and 1.0 sec off
7
6.1 Technical data of the subclasses
Subclass:
-211
-212
-213
Stitch type:
301
301
301
Hook type:
oscillating hook
Needle system:
DPx5 (134)
DPx17 (135x17)
Needle size:
[Nm]
80 - 110
80 - 110
100 - 120
Needle size
standard:
[Nm]
90
90
120
50/3 - 120/3
50/3 - 120/3
30/3 - 120/3
Thread size:
Stitch length:
Max. speed
[mm]
dependent on seam pattern
[min -1 ]
Clamp stroke
Delivery
maximum
[mm]
Sewing field size
max. in X-direction:
max. in Y-direction:
[mm]
2700
13
17
40
20
13
17
dependent
on clamp
Number of standard bartacks
40
Number of seam pattern
sequence programs
25
Number of seam patterns per
seam pattern sequence program
20
connectable / disconnectable
Sewing drive:
Rated voltage:
Rated load:
8
50
Number of storable
modifiable bartacks
Soft start:
DC-Motor
[V]
[kW]
40
20
1 ~ 230V/ 50/60 Hz
0,45
7.
Operating
7.1 Threading needle thread
Caution: Danger of injury !
Switch off main switch !
Thread the needle thread only when the automatic bartacker
is switched off.
–
–
Put thread reels on the thread reel holder and conduct needle
thread and bobbin thread through the unwinding arm.
The unwinding arm must be positioned vertically above the thread
reels.
Thread the needle thread as shown on the following illustration.
1
9
7.2 Adjust needle thread tension
3
2
1
Pretension 3
With open main tension 2 a minor residual stress of the needle thread
is required. The residual stress is produced by the pretension 3.
At the same time the pretension 3 influences the length of the cut
needle thread end (initial thread for the next seam).
– Short initial thread:
Turn knurled nut 1 in clockwise direction.
– Long initial thread:
Turn knurled nut 1 counter-clockwise.
Main tension 2
The main tension 2 has to be adjusted as low as possible.
The interlacing of threads should lie in the middle of the fabric.
In case of thin fabrics too high thread tensions can lead to undesirable
ruffling and thread breakage.
– Adjust main tension 2 in such a way that an even stitch pattern is
achieved.
Increase tension
= Turn knurled nut in clockwise
direction
Reduce tension
= Turn knurled nut counter-clockwise
7.3 Open needle thread tension
Automatic
The needle thread tension is automatically opened when trimming the
thread and when lifting the fabric clamping feet.
10
7.4 Adjust thread regulator
1
3
2
1
Caution: Danger of injury !
Switch off main switch !
Adjust thread regulator only when the automatic bartacker
is switched off.
The thread regulator 3 controls the needle thread quantity required for
the stitch formation.
Only a precisely adjusted thread regulator guarantees an optimum
sewing result.
When the thread regulator is adjusted correctly, the needle thread loop
must slide over the thickest spot of the hook with low tension.
– Loosen screw 1.
– Change position of the thread regulator 3.
Thread regulator to the left = larger needle thread quantity
Thread regulator to the right = minor needle thread quantity
– Tighten screw 1.
Adjustment hint:
If the largest thread quantity is required, the thread controller spring 2
must be pulled down by approx. 0.5 mm from its upper end position.
This is the case when the needle thread loop passes the maximum
hook diameter.
11
7.5 Wind on bobbin thread
5
1
4
3
2
6
–
–
–
–
–
–
Put bobbin on bobbin winder 4.
Pull thread through guide 2 and around tension 1.
Wind thread counter-clockwise around the core of the bobbin
(approx. 5 times).
Press winder lever 3 into the bobbin.
Sewing
The winder lever stops as soon as the bobbin is full.
Tear off thread at thread clamp 5 after winding on is finished.
Note !
If the thread is to be wound on without sewing,
the thread winding mode can be altered in submenu 6 “Special
functions”.
On
Off
If the thread winding mode is active, the sewing motor can be started
via pedal or push button independent of the sewing field drive (here
unthread at the thread lever).
For adjustment see chapter 8.5.1 “Thread winding mode”.
12
7.6 Change hook thread bobbin
1
7
4
2
5
6
2
3
1
Caution: Danger of injury !
Switch off main switch !
Change hook thread bobbin only when automatic bartacker
is switched off.
Take off empty bobbin
– Pull down hook cover 3.
– Lift bobbin case cover 1.
– Take off top of bobbin case 2 with bobbin 6.
– Remove empty bobbin from the top of the bobbin case 2.
Insert full bobbin
– Place full bobbin in the top of bobbin case 2.
– Thread bobbin thread through slot 5 below tension spring 7 in the
drill-hole 4.
– Pull bobbin thread out of bobbin case 2 for a length of approx. 2.5 cm.
When winding off the thread the bobbin must turn in the direction of
arrow.
– Reinsert bobbin case 2.
– Shut bobbin case cover 3.
13
7.7 Adjust bobbin thread tension
1
2
3
Caution: Danger of injury !
Switch off main switch !
Adjust bobbin thread tension only when the automatic bartacker
is switched off.
The required bobbin thread tension is to be produced by tension spring
1. The top of bobbin case 3 should drop slowly due to its own weight
when being held at the threaded-in bobbin thread.
Adjust tension spring
– Take off top of bobbin case 3 with the bobbin.
– Adjust tension spring 1 at the regulating screw 2 until the required
tension value is reached.
– Reinsert top of bobbin case.
14
7.8 Change needle
2
3
2
1
1
1
Caution: Danger of injury !
Switch off main switch !
Change needle only when the automatic bartacker is switched off.
–
–
–
Loosen screw 1.
Push new needle into the drill-hole of needle bar 2 as far as it will
go.
ATTENTION !
The hollow groove 3 of the needle must point to the hook.
Tighten screw 1.
ATTENTION !
After the changeover to another needle size the distance between
hook and needle has to be corrected (see service instructions).
15
8.
Operating the control of cl. 510
8.1 The control panel
For the input and output of data a control panel with an LCD display
and function keys is used.
P-key:
Programming mode
S-key:
SequenceProgramming mode
ESC-key
F-key:
Technician mode
Cursor keys
OK-key
8.1.1
The keys
Function key
Function
Cursor keys
If no text field is activated:
Press key “ï” to return from a submenu to the parent menu.
If a text field is activated:
Change between the points (this does not refer to the selection of
seam patterns or sequences).
In the sewing mode in case of sequence operation:
Change to the next or to the preceding seam pattern.
16
Function key
Function
If no text field is activated:
Change between the lines of the menus.
The selected line is displayed white on black.
If a text field is activated:
Increase or reduce the value of the respective point by one or change
between the parameters in case of functions with several choices.
OK-key
If no text field is activated:
Activate the text field.
The value can be altered with the keys “ñ ” and “ò ”.
If a text field is activated:
The set value is taken over.
If the clamping foot has been lowered using the keys OK + F:
The test procedure will be started.
ESC-key
If test functions are activated (Multitest / 180° disc):
You return to the selection menu.
1
If a text field is activated:
An input is aborted.
The preceding value is maintained.
In the technician and programming level
The control changes over to the sewing mode.
In the sewing mode
Lift clamping foot and stop sewing operation.
P-key
The control changes over from the sewing mode to the programming
mode. In this mode altered stitch patterns can be memorized under a
new program number.
S-key
The control changes over from the sewing mode or seam pattern
programming mode to the sequence programming mode. In this mode
it is possible to create new sequences or to alter existing ones.
F-key
The control changes over from the sewing mode to the technician
mode.
This mode can only be activated after a code has been entered.
In this operating status it is possible to set basic machine parameters
and to retrieve diagnosis and adjustment programs.
OK-key + F-Taste
Starts the testing mode* for the sewing procedure. The clamping
foot is lowered.
* Testing mode = a slow following of the seam contour without effectuating a seam
17
8.2 User interface
8.2.1
Structure of menu
Switch on
main switch
Key F
Service mode
Code 1
Sewing mode
Key ESC
Key ESC
Key F
Code 1
Key P
Key
ESC
Programming mode
Technician mode
Key S
Key S
Key P
Sequence programming mode
Call up the service mode
– Press the function key “F” and keep it pressed.
– Switch on main switch.
The control unit will be initialized.
After a short while the window for entering the code
number will appear.
– Enter the code number (code 1, compare chapter 8.5.4).
The display changes to the service menu.
18
Recall technician mode
– Switch on main switch.
The control is initialized.
The sewing mode menu appears on the display.
– Press key “ F ”.
–
Enter Code 1 (see Chapter 8.5.4).
–
Press key “OK” .
The display changes over to the technician mode.
8.3 Alter numerical values, parameter values, selection of alternatives
8.3.1
Alter numerical values
1
–
Select the desired line with the keys “ñ” or “ò”.
–
Press key “OK ”.
The chosen numerical value is marked by a blinking cursor.
Change between the points with the keys “ï” or “ð ”.
Increase or reduce the value of the selected point by one with the
keys “ñ ” or “ò ”.
–
–
Press key “OK ”.
The currently set value is taken over.
or
– Press key “ESC”.
The original value is maintained.
Note
All values can only be altered within the minimum and maximum
values.
19
8.3.2
Selection of a parameter
Some parameters offer a selection of non-modifiable adjustments.
–
Select the desired line with the parameter to be altered with the
keys “ñ ” or “ò ”.
–
–
Press key “OK ”.
Change between the given possibilities with the keys “ñ ” or “ò ”
Example:
Seam pattern number
–
Press key “OK ”.
The currently set parameter is taken over.
or
– Press key “ESC “.
The original parameter is maintained.
8.3.3
Selection of alternatives
Some menu items can be selected alternatively.
The current selection is marked with a checkmark (...ü).
If another alternative is selected, the marking of the current choice is
removed and the new menu item is marked.
Alternatively selectable items are optically set off against other menu
items by a separating line.
On
20
8.4 Seam patterns
Three different seam pattern types are available for the automatic
bartacker 510:
·
Specified standard seam patterns (Type 1) (see chapter 11)
The sewing parameters length, width and sewing speed can be
altered in the sewing mode; the laser marking lamps can be
switched on and off. The alterations are memorized.
However, after selection of another seam pattern the alterations
will get lost.
For these seam patterns the seam pattern numbers 1 to 50 are
available which cannot be deleted or overwritten.
·
Programmable seam patterns (Type 2)
Specified standard seam patterns can be altered in the
programming level (length, width, sewing speed, laser light 1 to 8)
and memorized under a new program number.
For these seam patterns the seam pattern numbers 51 to 90 are
available which can be deleted or overwritten.
·
Free seam contours (Type 3)
For these seam contours the seam patterns numbers 91 to 99 are
available. The creation of free seam contours is described in
chapter 8.5.4.4.
The sewing parameters length, width and sewing speed can be
altered in the sewing mode; the laser marking lamps can be
switched on and off. The alterations are memorized.
However, after selection of another seam pattern the alterations
will get lost.
21
1
8.5 Main menu
8.5.1
Seam pattern operation
The parameters for the individual seam patterns are arranged in the
main menu.
The seam patterns can be altered via these parameters.
–
–
–
Switch on main switch.
The control is initialized.
The main menu appears.
Select desired parameter with the keys “ñ” or “ò”.
The symbol of the selected parameter is displayed white on black.
Alter selected parameter as described in chapter 8.3.
Menu item
The symbol in the top left corner of the display describes
the currently selected menu item.
Bartack pattern
The symbol down on the left of the display shows the
current bartack pattern.
Seam pattern
Via this parameter the seam pattern to be sewn
is selected.
Selection: 1 .. 51 (52 to 99 if available)
Speed
Via this parameter the desired speed is set.
Input:
0 to 2700 rpm
Submenu seam pattern dimension
Select the present menu to set the seam pattern length
and width.
Display:
present length/width
Submenu seam pattern offset
Select the present menu to shift the seam pattern offset in
X-/Y-direction.
Display:
present X-/Y- offset value
22
Submenu
Behind this symbol there is a submenu.
Number of stitches
Via this menu line the number of stitches is indicated (cannot be
modified).
When selecting the line with key “OK” the submenu “Special functions”
is opened.
Counter reading
Via this menu line the following counters can be read:
Counter of daily number of pieces
or
Counter of capacity
When selecting the line with key “OK” the submenu “Counter of daily
number of pieces/Counter of capacity” is opened.
1
Submenu seam pattern dimension
Width
Setting the seam pattern width
Input: 0,1 ... 40,0 [mm]
Length
Setting the seam pattern length
Input: 0,1 ... 20,0 [mm]
23
Submenu seam pattern offset
In this menu to it is possible to change the seam pattern position in
X-/Y-direction.
When switching to this menu, the clamping foot will be lowered. If the
value for the X- and Y-Offset is changed, the stepping motors will move
the material accordingly. When exiting the submenu, the clamping foot
will then be raised again.
Caution: Danger of Injury!
Do not reach into the working area of the clamping foot when entering,
exiting the above submenu and performing changes within the seam
pattern offset.
X-Offset
Setting the seam pattern offset in X-direction.
Input: -20,0 ... +20,0
Y-Offset
Setting the seam pattern offset in Y-direction.
Input: -10,0 ... +10,0
Submenu “Special function and soft start status”
OFF
OFF
Thread winding mode
The bobbin thread winder can be operated separately.
At the setting “ON” the sewing motor can be started independent of the
step motors via pedal or key.
Input:
ON / OFF
24
Winding thread on to a bobbin:
With pedal
– Step pedal forwards (step 2).
The sewing motor starts.
– Step pedal backwards.
The sewing motor stops.
Via control panel
– Press “F” key .
The sewing motor starts.
– Press “ESC” key.
The sewing motor stops.
With push button (optional)
– Press key 2.
The sewing motor starts.
– Press key 1.
The sewing motor stops.
1
Soft start
Via this parameter the soft start can be switched on or off.
Input :
ON/ OFF
Submenu laser marking light (optional)
The menu item is only available if the laser light in the
technician level stands at “ON”.
Laser light 1 ... 3
Switching on/off of the laser marking lights 1 to 3.
Input :
ON/ OFF
25
Submenu counter of daily number of pieces or counter of capacity
OFF
Alternative display of counter of daily number of pieces or counter of
capacity.
Both counters work in parallel operation.
It can be selected which counter is displayed in the main menu.
·
·
–
The counter of the daily number of pieces counts the number of the
sewn seam patterns
Display: 0 … 65000
The bobbin thread counter works backwards.
When the value “0" is reached and a sewing operation is started, a
note is indicated.
Display: 9999 … 0
Press key"ESC “.
Back to the main menu.
If the counter of daily number of pieces is set, the following
display appears:
Display: counter of daily number of pieces in the sewing mode
Input:
Select with key “OK”.
Display: counter of capacity in the sewing mode
Input:
Select with key “OK”.
Reset counter of daily number of pieces
– Press key “OK ” twice.
The piece counter is reset to “0".
Counter of capacity on/off
Input:
ON/OFF
Initial value counter of capacity
Input:
0 … 9999
26
8.5.2
Programming mode
Under this menu item the parameters for programming of seam
patterns are arranged.
With the help of the parameters shape, length, width, speed etc. of the
seam pattern are entered.
Off
–
Switch on main switch.
The control is initialized.
The main menu appears.
–
Press function key “P” on the main menu.
The display changes over to the menu of the programming mode.
Select desired parameter with the keys “ñ ” or “ò ”.
The symbol of the selected parameter is displayed white on black.
Alter selected parameter as described in chapter 8.3.
–
–
Number of seam pattern
Via this parameter the number of the seam pattern to be created or
altered is selected.
When preparing a new programme an asterisk (*) is indicated before
the number.
Input:
51 … 90
– Select desired seam pattern programme with the keys “ñ ” or “ò ”.
– Press key “OK ”.
The program is activated.
Basic seam pattern
Via this parameter a standard seam pattern can be selected on the
basis of which the new seam pattern is to be created.
Input:
1 … 50 or
91 … 99 if available
Sewing speed
Via this parameter the desired sewing speed can be adjusted.
Input:
0 … 2700 [rpm]
Submenu seam pattern dimension
Select the present menu to set the seam pattern length
and width.
Display:
present length/width
27
1
Submenu seam pattern offset
Select the present menu to shift the seam pattern offset in
X-/Y-direction.
Display:
present X-/Y- offset value
Number of stitches
Only indicates the number of stitches.
Soft start
Via this parameter the soft start can be switched on or off.
Input :
ON/ OFF
First clamp (optional)
With this menu item you can set which part of the clamping foot (left or
right) will be lowered first. The menu item will only be displayed, if in
the menu equipment the option lowering clamping foot separately is
activated.
Input:
1/2 (left/right)
Submenu laser marking light (optional)
This menu item will only be displayed if the option Laser light is
activated in the menu equipment.
Laser light 1 ...3
Switching on/off the laser marking light 1 to 3.
Input:
ON/ OFF
28
8.5.3
Seam pattern sequences
8.5.3.1 Switching the sequence programming mode on or off
Changeover from the seam pattern operation to the seam pattern
sequence operation
– Actuate the function key “S” while the main menu is being
displayed in order to skip to the sequence programming mode.
0
–
–
–
–
–
Start the editing by actuating the „OK “ key
Select any sequence by using the “ñ “ key (1-25)
Confirm the selection by actuating the „OK“ key.
The seam pattern sequence operation is switched on.
Actuate the key „ESC “ or the “ï “ key.
The main menu for the seam pattern sequence operation will be
displayed
1
The menu items sequence number and sequence in the main menu
will be described at the end of this section.
29
Skipping from seam pattern sequence operation to seam pattern
operation
– Actuate the function key “S” while the main menu is being
displayed in order to skip to the sequence programming mode.
3
1
0
–
–
–
–
30
Start the editing by actuating the „OK “ key.
Select the sequence number 0 by using the “ò “ key.
Confirm the selection with the „OK“ key.
The seam pattern sequence operation is switched off.
Actuate the „ESC “ key or the “ï “ key.
The main menu for the seam pattern operation will be displayed.
Menu items in the main menu of the seam pattern sequence
Sequence
Selection of the seam pattern sequence.
Input:
1 (2 … 25, if available)
Sequence succession
Display of the sequence succession.
The current seam pattern number is marked with a bar (underlined).
In case of more than five numbers the display is scrolled.
–
Further seam patterns right:
Further seam patterns left:
Further seam patterns left and right:
1
Automatic operation
After the completion of a seam pattern the control changes over to the
next seam pattern shape automatically.
After sewing of the last seam pattern the control changes over to the
first seam pattern within the sequence again.
The current seam pattern is marked by a bar below the number.
The shape of the selected seam pattern is indicated on the left half of
the display.
Manual operation
The control does not change between the seam patterns automatically.
– Select the next seam pattern with the keys “ï ” or “ð ”.
The shape of the selected seam pattern is indicated on the left half
of the display.
Change between automatic and manual operation
– Select the second menu line with the keys “ñ ” or “ò ”
(sequences) .
– Press key “OK”.
– Select the kind of operation with the keys “ñ ” or “ò ”.
In case of automatic operation arrows are indicated between the
seam patterns.
Automatic operation
Manual operation
31
8.5.3.2 Sequence programming mode
In this menu item individual seam patterns are combined to retrievable
seam pattern sequences.
Totally 25 independent seam pattern sequences are available. Every
seam pattern sequence can be combined out of 20 seam patterns in
any order whatever.
–
–
–
–
Switch on the main switch.
The control is initialized.
The main menu appears.
Press function key “S” in the main menu.
The display changes over to the menu of the sequence
programming mode.
Select desired menu item with the keys “ñ” or “ò”.
The menu line is displayed white on black.
Press key “ESC ” or key “ò”.
Back to the main menu.
Sequence number/ seam pattern sequence operation
Selection of the sequence to be created or to be altered.
When preparing a new programme, an asterisk (*) is indicated before
the number.
Input:
0 … 25
– Select desired sequence number with the keys “ñ” or “ò”.
If the seam pattern sequence operation is to be switched off, select
the sequence number 0.
The sequence number is displayed white on black.
– Press key “OK ”.
The program is activated.
Seam pattern number (1 .. 20)
With this menu item you select the seam pattern number to be taken up
in the current sequence.
Input:
1 … 51 (52 - 99 if available)
32
8.5.4
Technician mode
In the technician mode the following menus are included:
Machine configurations
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
machine config
user config.
service functions
free contours
memory dongle
In this menu machine-specific adjustments are made.
User configurations
1
machine config
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
operat.config.
test functions
free contours
memory dongle
In this menu operation-specific adjustments are made.
Service functions
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
machine config
operat.config.
test functions
free contours
memory dongle
The service functions allow a quick verification of all hardware
components.
31
Free contours
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
machine config
operat.config.
test functions
free contours
memory dongle
With the automatic bartacker 510 up to nine freely defined seam
contours can be created and sewn. The coordinates are entered
directly at the control panel.
Memory dongle
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
machine config
operat.config.
test functions
free contours
memory dongle
With the help of the memory dongle, data can be transferred from the
machine to the dongle or vice versa.
34
Recall technician mode
– Switch on main switch.
The control is initialized.
The main menu appears.
– Press function key “F” in the main menu.
The screen for the code entry appears.
–
Enter code number “25483".
After input of the correct code number the display changes over to
the menu ”Technician mode".
–
Confirm with key “OK”.
The following menu appears:
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
1
machine config
user config
service functions
free contours
memory dongle
–
Select desired submenu with the keys “ñ” or “ò”.
–
Switch into the selected submenu with the key “OK”.
Cycle time
Indication of the cycle time of the seam pattern sewn last.
(time from sewing start to sewing end)
35
8.5.4.1 Machine configuration
Parameter
Softstart
Einrichtung
Zeiten
parameter
soft start
sew. equipment
times
262
Parameter
In this submenu different machine parameters can be set.
Soft start
In this submenu the driving speeds for the soft start slope can be set.
Equipment
In this submenu the settings for the sewing equipment and optional
units can be actuated.
Times
In this submenu different timings can be set.
Machine cycles
The total number of the sewn cycles is displayed.
36
Submenu machine parameters
cut.rpm
max.rpm
stop pos.
sew.st.pt.
softstart
Referenz.:
1
sew. equipment
–
Select desired parameter with the keys “ñ” or “ò”.
The symbol of the selected parameter / submenu is displayed white
on black.
–
Start selected parameter with the key “OK” or change into the
submenu.
1
Cutting speed
Input of the sewing motor speed in the last three stitches.
Input:
100 … 600 [rpm]
Maximum sewing speed
Input of the maximum adjustable sewing speed
Input:
2000 … 2700 [rpm]
Stop position
With the stop position the positioning of the sewing motor / needle bar
can be altered.
Input:
0
= thin fabrics
-15
= thicker fabrics
Note
The stop position is required for adjusting the corresponding material
thickness.
Feeding position
Selection of the material feeding position.
Input:
A = Seam beginning point
B = Machine neutral point
Note
According to the feeding position the following advantages /
disadvantages arise:
Feeding point A
= shorter cycle time
Feeding point B
= easier feeding of large seam patterns,
longer cycle time
37
Referencing
In this menu point the referencing mode of the step motor after the
sewing process can be configurated.
Input:
0
= no referencing
1
= referencing each time
2 – 10
= referencing after each 2nd to 10th sewing
process
Submenu Soft start
In this submenu speed adjustments for the soft start can be made.
Speed first stitch
Input of the speed in the first stitch.
Input:
400 … 900 [rpm]
Speed second stitch
Input of the speed in the second stitch.
Input:
400 … 2700 [rpm]
Speed third stitch
Input of the speed in the third stitch.
Input:
400 … 2700 [rpm]
Speed fourth stitch
Input of the speed in the fourth stitch.
Input:
400 … 2700 [rpm]
Speed fifth stitch
Input of the speed in the fifth stitch.
Input:
400 … 2700 [rpm]
38
Submenu sewing equipment
In this submenu adjustments for the sewing equipment can be made.
w.clamp f.
open dimens
number
length
width
Ausstattung
laserl.
Note
The entry of the clamping foot number (cf. chapter 12) serves for the
automatic verification whether the seam pattern to be currently sewn is
positioned within the inner frame of the clamping foot.
If the clamp numbers 9 to 13 are selected, only certain seam pattern
numbers and sequence numbers are allowed.
If no clamping feet are specified, also free dimensions can be defined.
Clamping foot
Selection of a specified clamping foot as equipment.
Input:
Alternative
Open dimensions
Selection of a clamping foot with free sewing field.
Input:
Alternative
Number
Selection of a DA clamping foot number.
Input:
1 .. 13
39
1
Clamping foot
number
Max.
tack size
(X x Y) [mm]
Dim. X x Y
[mm]
Inner frame
Inner frame
rectangular
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
19.0 x 3.5
20.0 x 4.1
27.0 x 5.0
10.0 x 4.5
5.6 x 23.0
19.0 x 12.0
44.0 x 24.0
9.5 x 4.5
16.0 x 16.0
12.0 x 14.0
24.6 x 12.6
12.6 x 21.0
34.8 x 12.2
16.0 x 2.6
8,6 x 13,6
20.0 x 4.5
21.0 x 5.1
27,0 x 5,0
10,0 x 4,5
5,6 x 23,0
19,0 x 12,0
44,0 x 24,0
9,5 x 4,5
16,0 x 16,0
12,0 x 14,0
24,6 x 12,6
12,6 x 21,0
34,8 x 12,2
17,0 x 3,6
24,0 x 14,6
yes
yes
yes
yes
yes
yes
yes
yes
no
no
no
no
no
yes
no
Description
Straight bartack
Straight bartack
Straight bartack, large
Straight bartack, small
Longitudinal bartack
Small field clamping foot
Large field clamping foot
Contraction clamp
Circle
D-clamping foot, simple
Double D-clamping foot, lateral
Double D-clamping foot, longitud.
Double Tri-clamping foot, lateral
“Belt loop”
Double D-clamping foot, lateral
Length
Input of a freely selectable sewing field.
Input only possible in case “free clamp dimension”
had been selected. Otherwise the length / width of
the selected clamp is indicated (cannot be modified).
Input:
0.5 … 20.0
Width
Input of a freely selectable sewing field.
Input only possible in case “free clamp dimension”
had been selected. Otherwise the length / width of
the selected clamp is indicated (cannot be modified).
Input:
0.5 … 40.0
Configuration
Via this submenu the optional units can be activated.
Danger of Breakage!
When making the clamps for open dimensions a safety margin
must be considered.
40
Submenu Configuration
hand switch:off
el. thr. wiper:off
_/-clamp:
off
laser light: off
thr. burner off
opt. sign.
assignment input
Further optional equipments are available. Please contact our
application centre (APC).
Hand switch
Activating of optional hand switches. When the option is switched on, a
menu item in order to select the operation mode will appear in the
menu “User configuration”.
Input:
ON/OFF
Electric thread wiper
Activating of optional electric thread wipers (instead of the mechanic
thread wiper).
Input:
ON/OFF
Separate lowering of the clamping foot
Activating the operating of the optional separate clamping feet.
Input:
ON/OFF
Operating the separate lowering of the clamping foot
NOTE!
The function is only available with seam pattern programs (variants).
Sewing procedure with pedal
– Push the pedal to the front to level 1: clamp 1 will be lowered
– Move the pedal into resting position
– Push the pedal again to the front to level 1: clamp 2 will be lowered
– Push the pedal to level 2: the sewing process will be started
– Push the pedal back to level:
the clamp closed last will be lifted again
– Push the pedal back to level and keep it pushed (0,8 sec.): clamp 1
and clamp 2 will be lifted one after the other
41
1
Testing mode with the control panel BF3
– Actuate the keys “OK” + “F”: clamp 1 will be lowered
– Actuate the “OK” key: clamp 2 will be lowered
– Actuate the “OK” key again: the testing process will be started
– Actuate the “ESC” key: the clamp closed last will be lifted again
Sewing process with the hand switch (optional)
– Actuate key 1: clamp 1 will be lowered
– Actuate key 2: clamp 2 will be lowered
– Actuate key 2 again: the sewing process will be started
– Actuate key 1: the clamp closed last will be lifted again
– Actuate key 1 and keep it pressed (1,5 sec.): clamp 1 and clamp 2
will be lifted
Laser lights
Activating the 3 optional laser lights.
Input:
ON/OFF
Thread burner
Activating the optional thread burner device. If the option thread burner
is switched on, the menu items t5 - t9 are listed under machine/ timings
allowing the setting of various times.
Input:
ON/OFF
Optical signalling
Via this submenu an indication of error and event messages and of the
message “hook thread is zero” can be configurated and activated via
two 24V-outputs.
Optical signalling
Activating of the indication. Beforehand outputs 1 and 2
must be configurated, otherwise this menu item cannot be
selected.
Input:
ON/OFF
Output 1
Selection of the output for error and event messages.
Input:
1 ...8 (if 24V-outputs are vacant)
Output 2
Selection of the output for the message “hook thread is
zero”
Input:
1 ...8 (if 24V-outputs are vacant)
Assignment of the inputs
This menu item gives on overall view of the assignment of the inputs
with (optional) units.
Assignment of the 24V-outputs
This menu item gives an overall view of the assignment of the
24V-outputs with optional units.
42
Submenu Times
The submenu times is only displayed, when the corresponding options
are activated or the seam patterntoring switch of the clamping foot is
not connected.
Delay between pedal level 1 (lowering the clamping foot) and
sewing start (t1)
Time only relevant with quick start via pedal or hand switch (optional).
The above menu item will only be displayed, if the monitoring switch of
the clamping foot is not connected.
Input:
50 ...300 ms
Preset value:
250 ms
Turn-on delay for the thread wiper magnet (t2)
This menu item will only be displayed if the option “electric thread
wiper” is activated in the menu “equipment”.
Input:
30 ...100 ms
Preset value:
40 ms
Delay thread wiper magnet off - clamping foot magnet on (t3)
The delay between the switching off of the thread wiper magnet and
the switching on of the clamping foot magnet.
This menu item will only be displayed if the option “electric thread
wiper” is activated in the menu “equipment”.
Input:
0 ...300 ms
Preset value:
50 ms
Delay between clamping foot magnet on —reference run (t4)
The delay between the switching on of the clamping foot magnet and
the referencing of the step motors.
Input:
0 ...300 ms
Preset value:
100 ms
43
1
The menu items t5 - t9 will appear, only if the option “thread burner” is
activated under menu machine/equipment/configuration.
Time to preheat the burner
Time allocated for the preheating of the burner points before the seam
end.
Input:
0 ... 5000ms
Preset value:
2000ms
Select only the necessary time needed for the burning of the threads,
otherwise the burner points can be damaged.
Delay before thread puller
Delay after advancing the lower thread burner puller, after the thread
puller (thread wiper) is activated.
Input:
0 ... 500ms
Preset value:
100ms
Delay before upper burner
Delay after the activation of the thread puller (thread wiper), after the
upper thread burner is advanced.
Input:
0 ... 500ms
Preset value:
100ms
Time thread puller (thread wiper) on
The duration of the thread puller (thread wiper) is switched on.
Input:
0 ... 3000ms
Preset value:
2000ms
Delay heating burner off
Delay after the thread puller (thread wiper) is turned off, after the
heater of the burner is turned off.
Input:
0 ... 500ms
Preset value:
100ms
44
8.5.4.2 User configurations
In this menu operation-specific adjustments are made.
language
sewing mode
manual keys
param.mod
forced st
pattern locking
sequence locking
–
Select desired parameter/ submenu with the keys “ñ ” or “ò ”.
The selected parameter/ submenu is displayed white on black.
–
Start selected parameter with the key “OK” or change into the
submenu.
1
Language
In this submenu the language can be chosen.
German
Selection of the German language for the technician level.
English
Selection of the English language for the technician level.
Parameter
Selection of the numbering of menu items for the
technicial level (see chapter 13).
45
Operating mode push button (optional)
Selection of the push button mode.
This menu item is only available if the “hand switch” option in the menu
configuration is switched on.
Input:
A = Normal
B = Quick start
In the push button mode “NORMAL” the keys have the following
functions:
Key 1:
Lifting and lowering of the clamping foot.
Interruption of the sewing operation.
Sewing operation stopped after interruption.
Key 2:
Sewing start when clamping foot is lowered.
Interruption of the sewing operation.
Sewing operation continued after interruption.
In the push button mode “QUICK START” the keys have the following
functions:
Key 1:
Lifting and lowering of the clamping foot.
Interruption of the sewing operation.
Sewing operations stopped after interruption.
Key 2:
Sewing start.
If clamping foot is not lowered, it will be lowered.
Interruption of the sewing operation.
Sewing operation continued after interruption.
Parameter locking
Switching on / off of the parameter alteration in the sewing and
programming mode.
Input:
ON / OFF
Note
If the parameter locking is switched on, any alteration of parameters in
the sewing and programming mode is no longer possible.
46
Lock seam pattern
In this submenu individual seam patterns can be released or locked
for selection in the sewing mode.
lock all
unlock all
on
on
on
on
on
on
Note
If a clamp with non-rectangular shape (Number 9 to 13) is selected in
the menu “Machine configuration/ Equipment”, a manual locking is not
possible. The menu item cannot be selected because for these
clamping feet only specified seam patterns are defined (see table of
seam patterns chapter 11).
In general the following restrictions apply:
1. Seam pattern operation
·
·
The seam pattern currently selected in the sewing mode cannot be
locked.
In the sewing mode, locked seam patterns cannot be chosen from
the selection list.
Locked seam patterns are marked with “#”.
2. Seam pattern sequence operation
·
·
A locked seam pattern can be selected in a sequence. However,
when starting the sewing process (lowering of the clamping foot)
an error message appears. The sewing process cannot be started.
The last seam pattern selected in the seam pattern operation
cannot be locked.
Lock all
All seam patterns with the restrictions specified above will be locked.
The status of the displayed seam pattern number switches to “OFF”.
Unlock all
All seam patterns will be released.
The status of the displayed seam pattern number switches to “ON”.
Lock/unlock individual seam pattern
Input:
ON / OFF
47
1
Lock sequences
In this submenu individual sequences can be released or locked for
selection in the sewing mode.
The menu item is only displayed, if more than one seam pattern
sequence is programmed (compare with chapter 8.5.3)
lock all
unlock all
on
on
In general the following restrictions apply:
1. Seam pattern operation
·
The last sequence selected in the sequence operation cannot be
locked.
2. Seam pattern sequence operation
·
·
The sequence currently selected in the sewing mode cannot be
locked.
In the sewing mode locked sequences cannot be chosen from the
selection list.
Locked sequences are marked with “#”.
Lock all
All sewing sequences with the restrictions specified above will be
locked.
The status of the displayed sewing sequence number switches to “OFF”.
Unlock all
All sewing sequences will be released.
The status of the displayed sewing sequence number switches to “ON”.
Lock/unlock individual sewing sequence
Input:
ON / OFF
48
8.5.4.3 Service functions
The service functions allow the quick verification of all hardware
components.
Note
The service menu can also be reached directly when switching on the
machine (see chapter 8.2.1).
Multitest
multitest
180°-disc
events
1
In the menu “Multitest” all hardware components can be checked.
180° disc
Multitest
180° - Scheibe
Ereignisse
DAC III
INIT
multitest
180°-disc
events
This menu item offers a function for the correct adjustment of the
reference position of the sewing motor (180° disc) - see service
instructions.
Events
multitest
Multitest
180° - Scheibe
Ereignisse
DAC III
INIT
180°-disc
events
49
DAC III
Multitest
180° - Scheibe
Ereignisse
DAC III
INIT
multitest
180°-disc
events
DAC III
INIT
In this menu are indicated the different parameters of the control unit.
Initialization
Multitest
180° - Scheibe
Ereignisse
DAC III
INIT
multitest
180°-disc
events
DAC III
INIT
Via this menu the event memory buffer and the permanent data can be
reset to the factory setting.
50
Multitest
Selection of the submenu of Multitest
Ausgangstest
PWM-Ausg.test
Eingangstest
Auto-Eing-test
Nähmotortest
Schrittm.test
RAM-Test
EEPROM-Test
output test
input test
auto input tst
motor test
step.motor tst
RAM test
EEPROM test
PWM-output test
–
Select desired test function with the keys “ñ” or “ò”.
The selected test function is indicated white on black.
–
Choose selected test function using the “OK” key.
1
51
Output test
With this test function the function of the output elements is checked.
–
–
Start the test function with the key “OK”.
Select desired output element with the keys “ñ” or “ò”.
–
Switch desired output element on and off with the key “OK”.
output test
output
–
Press function key “ESC” for leaving the test function.
Caution: Danger of injury !
Do not reach into the running machine during the function test of the
output elements.
Output element
Function
Y1
Laser marking light 1, if the option is activated
Y2
Laser marking light 2, if the option is activated
Y3
Laser marking light 3, if the option is activated
Y4
Separated clamping foot 1, if the option is activated
Y5
Separated clamping foot 2, if the option is activated
Y6
Depending on the activated option and the output configuration
Y7
Depending on the activated option and the output configuration
Y8
Depending on the activated option and the output configuration
The recent configuration of the outputs is indicated in the submenu
“Output configuration” of the menu equipment.
52
PWM Output test
This test function checks the function of the magnets.
–
–
–
Start the test function by actuating the “OK” key.
Select the desired output element by actuating the “ï“ or “ð“ keys.
Switch the selected output element on and off by pressing the
“ñ” or “ò” keys.
PWM output test
output
–
–
–
The issued value for the selected output element is displayed. The
value specifies the impulse rate for the controlling of the output
element.
If the machine is equipped with a monitoring switch of the clamping
foot, the Output PWM-1 will have the value + or - will be displayed,
according to the switching status of the output element.
Actuate the function key “ESC” in order to leave the test function
Caution: Danger of injury !
Do not reach into the running machine during the function test of the
output elements.
Output element
PWM 1
PWM 2
PWM 3
Function
Clamping foot magnet
Trimmer magnet
Thread wiper magnet
53
1
Input test
With this test function the input element to be tested is selected.
ATTENTION !
The input elements have been carefully adjusted in the factory.
Adjusting and correcting must only be done by trained service staff.
Caution: Danger of injury !
Do not reach into the working area of the clamping foot when starting
and ending the input elements.
–
–
Start the test function with the key “OK”.
Select desired input element with the keys “ñ” or “ò”.
The switching status of the input element is indicated.
input test
input
–
Input element
Actuate the function key “ESC” in order to leave the test function.
The menu Multitest is indicated.
Function
S1
Pedal 1
S2
Pedal 2
S3
Pedal 3
S4
Pedal 4
S5
Hand switch 1, if the option is activated
S6
Hand switch 2, if the option is activated
S7
Depending on the option activated and the input configuration
S8
Check clamping foot
Ref. N
Referencing switch for the sewing motor
Ref. X
Y-reference switch
Ref. Y
X-reference switch
The recent configuration of the inputs is indicated in the submenu
“Input configuration” of the menu Equipment.
54
Auto-Input test
With this test function the function of the input elements is checked.
ATTENTION !
The input elements have been carefully adjusted in the factory.
Adjusting and correcting must only be done by trained service staff.
Caution: Danger of injury !
Do not reach into the working area of the clamping foot when starting
and ending the input elements.
–
–
Start test function with the key “OK”.
Actuate desired input element.
The switch status and the number of the actuated input element
are indicated.
auto input tst
–
Input element
1
Actuate the function key “ESC” in order to leave the test function.
The menu Multitest is indicated.
Function
S1
Pedal 1
S2
Pedal 2
S3
Pedal 3
S4
Pedal 4
S5
Hand switch 1, if the option is activated
S6
Hand switch 2, if the option is activated
S7
Depending on the option activated and the input configuration
S8
Check clamping foot
Ref. N
Referencing switch for the sewing motor
Ref. X
Y-reference switch
Ref. Y
X-reference switch
The recent configuration of the inputs is indicated in the submenu
“Input configuration” of the menu Equipment.
55
Sewing motor test
With this test function the sewing motor can be checked.
–
Start test function with the key “OK”.
–
–
Start motor with the key “ñ”.
Alter speed with the keys “ñ” or “ò”.
The speed is indicated.
motor test
–
56
Actuate the function key “ESC”.
The test is finished, the motor stops.
The sewing motor control makes a reference run and the clamping
foot is lifted.
The menu Multitest appears on the display.
Step motor test
With this test function the step motors and the pertaining reference
switches can be checked.
ATTENTION risk of breakage !
Before the test: Move needle in position “up” by using handwheel.
–
–
–
Start the test function with the key “OK”.
Check transverse motion of the step motor (X-axis).
Move step motor with the keys “ï” or “ð”.
The number of steps done is indicated on the left of the arrow.
The status of the reference switch changes around the reference
position.
Check longitudinal motion of the step motor (Y-axis).
Move step motor with the keys “ñ” or “ò”.
The number of steps done is indicated above the arrow.
The status of the reference switch changes around the reference
position.
1
step.motor tst
–
Actuate the function key “ESC”.
The test is finished.
The menu Multitest appears on the display.
57
RAM test
With this test function the static memory (SRAM and program data
memory) is checked.
–
–
58
Start test function with the key “OK”.
The display shows the test result.
Display
Explanation
SRAM OK
SRAM ERROR
NV-RAM OK
NV-RAM ERROR
Static Random Access Memory works perfectly
Error in the static memory
Program data memory is in order
Error in the program data memory
Actuate the function key “ESC”.
The test is finished.
The menu Multitest appears on the display.
EEPROM test
This test function checks the read memory (ROM) of the
micro-processor.
–
Start test function with the key “OK”.
The display shows the following test results:
- ROM-size
- Machine class
- Software version
- Software date
- Check sum and status
ROM size
class
version
date
check sum
1
Hint:
The data will vary depending on the software version.
– Actuate the function key “ESC”.
The test is finished.
The menu Multitest appears on the display.
.
59
Events
In case of failure the menu can give important hints regarding the
cause of the malfunction.
event memory
latest events
Event memory
= Ereignisspeicher =
E4304:
E8254:
3x
1x
(example)
In this menu item all events that occurred are indicated.
– Exit the menu item by actuating the “ESC” key.
– Continued display by actuating the “ ò” key.
Latest events
= Letzte Ereignisse =
1 E4304 Z
S
1 E4304 Z
S
1 E8254 Z
S
1154889
263
1152558
263
1150034
263
(example)
In this menu item the events that occurred last are indicated:
Z = milli-seconds after the switching on of the machine
S = machine piece counter
E = Event/Error number
– Exit the menu item by actuating the “ESC” key.
– Continued display by actuating the “ò” key..
60
DAC III
Selection of the submenu for the display of the DAC III parameters.
Temp. (°C): 30
UZK (V): 325
(example)
Temperature
Here the current inside temperature of the control unit is indicated
in °C. It should be below 80 ° C.
When the temperature of 80°C is exceeded, the error message 3107
will appear.
1
Intermediate circuit voltage sewing motor (UZK)
Here the current intermediate circuit voltage for the sewing motor
one-level is indicated.
61
Initialization (Init)
The selection of the submenu for the initialization of the event memory
and the permanent data.
Ereignissp.
Var . + Sequ.
Maschinenpar.
Fr. Konturen
Masch. kpl!
event memory
variants + sequences
machine parameters
free seam contours
machine complete
Event memory
Via this menu item the event memory can be reset to zero.
Seam pattern programs (variants) and sequences
Via this menu item seam pattern programs and sequences can be
deleted.
Machine parameters
Via this menu item machine parameters, soft start driving speeds,
timings, user configuration, hook thread counter data and options and
the existence of a monitoring switch for clamping foot to factory
settings can be reset.
Free seam contours
Via this menu item all free seam contours can be reset (deleted).
Note
Through resetting it may occur that seam pattern programs and
sequences are eventually deleted and numbers of subsequent
programs and sequences may be altered.
Machine complete
Via this menu item all permanent data can be reset. After resetting the
machine will automatically be restarted.
Note
After the restart of the machine, a new selection of the clamp numbers
and the equipment must be carried out (compare installation
instruction, chapter 9).
62
8.5.4.4 Free contours
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
machine
user
service
free contours
memory dongle
With the automatic bartacker 510 up to nine freely defined seam
contours can be created and sewn. The entry of the coordinates is
done at the control panel.
create
alter
delete
copy
1
no.st.av.
no.pat.av.
Creating
Via this menu item a new seam contour can be created.
Note
The number of the seam contour is issued automatically.
Altering
After selection of the seam contour to be altered you get into the
submenu for altering the seam contour.
Deleting
Via this menu item a selected seam contour can be deleted.
Copying
Any basic seam pattern number or free seam contour whatever can be
copied and altered. After selection of the seam pattern number you get
into the submenu “Alter seam contour”.
– Select desired function with the keys “ñ” or “ò”.
– Choose selected function with the key “OK”.
Note
Number of stitches:
The number of the stitches still available is indicated (max. 1000)
Number of seam patterns:
The number of the seam patterns still available is indicated (max. 9)
63
Determining the seam pattern coordinates
When creating a seam contour every individual stitch has to be entered
in the control indicating its position in the coordinate system (X- and
Y-axis). Therefore the individual coordinate points have to be
determined before. This can be done with the help of millimetre graph
paper.
Maximum sewing area
(grey field)
Stitch to be determined
Sketched seam contour
Machine neutral point
Coordinate system with X- and Y-axis
Note
The seam contour should be laid out in such a way that the machine
neutral point is in the middle of the seam pattern, if possible.
–
–
–
–
–
64
Sketch the maximum sewing field size on the millimetre graph
paper (X = max. 40 mm, Y = max. 20 mm).
Draw coordinate system in the centre of the sewing field.
Draw in seam contour.
Determine the X- and Y-coordinates for every desired stitch.
Enter X- and Y-coordinates in the control (see next page).
Create seam pattern
In this menu the X- and Y-coordinates are entered for every individual
stitch.
add stitch
parameter/end
Note
In order to enter stitch operations (f.e. intermediate cutting), first
complete the seam pattern (entering of the coordinates) and then
insert the stitch operation through editing in the menu “Changing seam
pattern”.
1
X1:
Input of the X-coordinate for stitch 1
Input:
-20.0 … +20.0
Y1:
Input of the Y-coordinate for stitch 1
Input:
-10.0 ...+10.0
Note:
The value X1 can be altered according to chapter 8.3.1.
Select the menu item Y1 with key “ò” after confirmation of the value
for X1 with key “OK”.
The values for Y1, X2, Y2, X3 and Y3 can be altered as described for
the value X1.
Select menu item “Add stitch” with key “ò” after confirmation of the
input of Y3 with key “OK”.
After selection of this line with key “OK” the next coordinates Xn+1 and
Yn+1 (here: X4 and Y4) are given in the two upper menu lines. The
selection bar changes to the line Xn+1 (here: X4) automatically. The
values Xn+1 and Yn+1 can be altered as described above when
required. This procedure can be repeated until the stitch coordinates
are completely entered. When the input of coordinates is finished, the
line “Exit” has to be selected in the submenu “Parameter/End”. Then
the menu “Free seam patterns” appears again.
Add stitch
Function for adding a stitch.
The coordinates for the first three stitches (here: X1/Y1, X2/Y2 and
X3/Y3) are shifted upwards and the display shows Xn+1/Yn+1 (here:
X4/Y4).
65
Submenu parameter
Selection of the submenu for entering the seam pattern parameters
std. rpm
orig. x
orig. y
end
Std. rpm:
Standard speed
Input:
100 … 2700 rpm
orig. X:
Reference point X for change of size
Input:
-10.0 … +10.0
orig. Y:
Reference point Y for change of size
Input:
-20.0 … +20.0
The reference point for the change of the seam pattern size is
individually and internally fixed for every seam pattern. Normally it is
the machine neutral point.
The following illustration shows the principle of size change under
consideration of the reference point:
Example seam pattern 1
Frame of clamping foot
seam pattern after
change of size
Reference point for
change of size
seam pattern before
change of size
66
Example seam pattern 2
Change seam pattern
stitch coordin
del.st.
add st.
append stitch
parameters
no.stitch
no.st.av.
Stitch coordinates
Selection of the submenu for altering the stitch coordinates.
Delete stitch:
Delete stitch.
Input:
Number of the stitch to be deleted
1
Add stitch:
Add stitch.
Input:
Number of the stitch in front of which a new stitch is to be
added.
The submenu for altering the stitch coordinate appears.
Add stitch (at the end)
The submenu for altering the stitch coordinate appears.
Parameter
Selection of the submenu for altering the seam pattern parameters.
Submenu stitch coordinates
If the seam pattern to be altered has less than 99 stitches, the
submenu appears immediately.
If the seam pattern to be altered has more than 99 stitches, the
following menu appears first:
–
Select desired range of stitches with the “ñ ” or “ò ” keys.
–
Select range of stitches with the key “OK”.
The submenu “Stitch coordinates” appears
67
1
99
–
Select desired stitch with the “ñ” or “ò” keys.
–
Select stitch with the key “OK”.
The submenu for altering a stitch coordinate appears.
If a stitch has a stitch operation attributed to it, it will be marked with
an asterisk (*) instead of a slash (/).
Submenu “Alter stitch coordinate”
This submenu appears when selecting a stitch coordinate from the
menu “Stitch coordinates” and after adding or altering a stitch.
X10:
Y10:
Op10:
0.0
0.0
1
(example)
X10
Altering the X coordinate for stitch number 10.
Input:
-20,00 … +20,00
Y10
Altering the Y coordinate for stitch number 10.
Input:
-10,00 … +10,00
OP10
Altering the stitch operation for stitch number 10.
Input:
0 … 1 (compare the chart below)
68
Note:
The stitch operation entered will be executed after the stitch.
Number of
operation
Description
Comment
0
No stitch operation
1
Intermediate thread cutting
The intermediate cutting can be
programmed up to 10 times within a
seam pattern. Between 2 intermediate
cuttings at least 3 stitches must be sewn.
1
Delete seam pattern
design
edit
delete
copy
no.st.av.
no.pat.av.
–
–
Select the function “Delete” with the “ñ” or “ò” keys.
Select desired seam pattern number with the “ñ” or “ò” keys.
–
Press the “OK” key.
The seam pattern is deleted.
ATTENTION!
By deleting a free seam contour the numbering of seam pattern
programs and/or sequences can be altered because it is possible that
these are deleted, too.
69
Copy seam pattern
design
change
delete
copy
no.stitch
no.st.av.
–
Select the menu item"copy “ with the “ñ “ or “ò “ keys.
–
–
Actuate the „OK “ key.
Select the desired seam pattern number (1-50,91-99) with the “ñ “
or “ò “ keys.
–
Confirm the selection by actuating the „OK “ key.
The seam pattern will be copied and the menu “Change seam
pattern” will be displayed.
stitch coordin.
delete stitch
insert stitch
append stitch
parameters
no.stitch
no.st.av.
In order to change the seam pattern, please follow the instructions of
the paragraph “Change seam pattern” on page number 64.
70
8.5.4.5
Memory dongle
Maschine
Benutzer
Service
Freie Konturen
Memory-Dongle
machine
user
service
free contours
memory dongle
By using the functions of this submenu, data can be transferred from
the machine to the dongle or vice versa.
Inhalt
Laden
Speichern
Formatieren
contents
1
load
save
formatting
Dongle contents
Via this menu item the contents of a dongle connected to the control
unit can be displayed.
Load
Via this menu item program data (seam pattern programs and
sequences) and machine parameters as well as free seam contours
can be transferred from the dongle to the machine.
Save
Via this menu item program data (seam pattern programs and
sequences) and machine parameters as well as free seam contours
can be memorized on a data dongle.
Formatting
In order to save data on a dongle, the dongle must be formatted as a
data dongle.
The dongle is to be inserted on the control unit into the plug connection
labelled „Dongle “ (X110).
71
Displaying the dongle contents
Boot dongle
If a boot dongle is inserted, information concerning the machine
program will be displayed.
Klasse:
510
U-Klasse:
000
Version:
A05
Datum: 100105
class
subclass
version
date
(example)
A boot dongle with a machine program for any machine class can be
inserted in order to display the dongle information.
Data dongle
If a data dongle, that has been formatted for the machine class 510 is
inserted, the memorized seam pattern programs or free seam contours
will be displayed.
Display of the memorized seam pattern programs
51:
52:
53:
54:
55:
56:
57:
58:
51
--------
(example)
It is possible to switch between the display of the memorized seam
pattern programs and the free seam contours by actuating the “ð“ key.
72
Display of the memorized free seam contours
(example)
If no seam pattern program or free seam contour is memorized, „—“ will
appear, otherwise the corresponding seam pattern name will be indicated.
If a dongle of another machine class is inserted, the following
information will be displayed.
1
Data Dongle
Klasse:
530
(example)
Transferring data from the dongle to the machine
The memorized program data (seam pattern programs and sequences)
and machine parameter or all free seam contours can be can be
transferred from the dongle to the machine.
Inhalt
Fr. Kont. kpl.
Masch. kpl.
contents
free cont. compl.
mach. compl.
73
Contents
Via this menu item the contents of a memory dongle connected to the
control unit can be displayed.
Free seam contours completely
Via this menu item the loading of all free seam contours will be started.
A window to confirm the selection will appear.
– Actuate the
“ï“ key (no), in order to cancel the transaction or the
“ð“ key (yes), in order to start the transaction.
All free seam contours memorized on the machine will be
deleted when loading the dongle!
Note
The time needed in order to load the data depends on the number of
free seam contours memorized on the dongle.
Machine completely
Via this menu item the loading of the program data (seam pattern
programs and sequences) and the machine parameters will be started.
They consist of:
·
·
·
·
·
all seam pattern programs
all sequences
machine parameters
recent seam pattern numbers, if the sewing equipment
corresponds
recent standard seam pattern data, if the sewing equipment
corresponds
A window to confirm the selection will appear.
– Actuate the
“ï“ key (no), in order to cancel the transaction or the
“ð“ key (yes), in order to start the transaction.
The data memorized on the machine will be deleted when
loading the dongle!
Note
The time needed in order to load the data depends on the number of
seam pattern programs memorized on the dongle.
If free seam contours in seam pattern programs (variants) and
sequences are to be transferred, first the free seam contours have to
be loaded on the machine and then “machine completely”!
74
Memorizing data on the dongle
Here program data (seam pattern programs and sequences) and
machine parameters or all free seam contours can be saved from the
machine to the dongle.
Inhalt
Fr. Kont. kpl.
Masch. kpl.
contents
free cont. compl.
mach. compl.
Contents
Via this menu item the contents of a memory dongle connected to the
control unit can be displayed.
Free seam contours completely
Via this menu item the saving of all free seam contours will be started.
A window to confirm the selection will appear.
– Actuate the
“ï “ key (no), in order to cancel the transaction or the
“ð “ key (yes), in order to start the transaction.
All free seam contours memorized on the dongle will be
deleted when the saving is started!
Note
The time needed in order to save the data depends on the number of
free seam contours memorized on the machine.
Machine completely
Via this menu item the saving of the program data (seam pattern
programs and sequences) and the machine parameters will be started.
They consist of:
·
·
·
·
·
all seam pattern programs
all sequences
machine parameters
recent seam pattern numbers, if the sewing equipment
corresponds
recent standard seam pattern data, if the sewing equipment
corresponds
75
1
A window to confirm the selection will appear.
– Actuate the
“ï “ key (no), in order to cancel the transaction or the
“ð “ key (yes), in order to start the transaction.
The program data and the machine parameters memorized on the
dongle will be deleted when the saving is started!
Note
The time needed in order to save the data depends on the number of
seam pattern programs memorized on the machine.
Dongle formatting
In order to save data on a dongle, the dongle must first be formatted as
a data dongle.
Data Dongle
data dongle
Data dongle
Via this menu item the formatting of the dongle can be started.
– In order to start, actuate the “P” key .
A window to confirm the selection will appear.
– Actuate the
“ï “ key (no), in order to cancel the transaction or the
“ð “ key (yes), in order to start the transaction.
When formatting a dongle all data memorized on it will be deleted!
76
Error messages
Number
Name
Possible cause
Elimination
4301
Dongle missing
No dongle inserted
Insert dongle into control unit
4302
Dongle empty
No data memorized on
dongle
Save data on the dongle
4304
Wrong dongle type
Dongle has the wrong
format for the selected
function
• Use a different dongle
• Format the dongle
4307
Wrong machine class
Data dongle is not formatted
for class 510
• Use another dongle
• Format the dongle
4311
Error format-ID
• Dongle not formatted
correctly
• Dongle defect
• Format the dongle again
• Use a new dongle
4312
Unknown dongle type
• Dongle not formatted
correctly
• Dongle defect
• Format the dongle again
• Use a new dongle
1
77
8.6 Error messages
In case of a fault in the control system or in the seam pattern program
the display shows a corresponding symbol and a fault number.
With the help of the following tables the cause of the fault can be
ascertained and remedial action can be taken.
8.6.1
No.
78
Error categories
Pictogram
Name
Description
1
Fatal Error
An emergency stop follows. The automatic
bartacker must be switched off and on again.
2
Error
Working can only be carried on after
confirmation of the error by the user.
3
Warning
Working can only be carried on after
confirmation of the warning by the user
8.6.2
Application messages
Pictogram
Description
Category
Capacity counter is “zero”
Hint
Handwheel turned
manually
Warning
seam pattern exceeds the
inner frame of the
clamping foot either -X or
+X direction
Warning
Contour exceeds the inner
frame of the clamping foot
in -X or +X direction and
Y-direction
Warning
Contour exceeds the inner
frame of the clamping foot
in -X and -Y direction or
+Y-direction
Warning
Contour exceeds the inner
frame of the clamping foot
in +X and -Y direction or
+Y-direction
Warning
Contour exceeds the inner
frame of the clamping foot
in X and -Y direction or
+Y-direction
Warning
Contour exceeds the inner
frame of the clamping foot
in -Y or +Y direction
Warning
Reaction / Troubleshooting
· Clamping foot can only be
lowered after
confirmation via the “OK” key.
After the confirmation, the hint
disappears.
· With the confirmation, the capacity
counter is reset to its
initial value again.
After interruption of the sewing procedure:
· Impossible to continue sewing
· Stop the sewing process by
stepping the pedal backwards,
confirmation with push button key 1
(clamps) or pressing the “ESC” key at
the control panel
·
·
·
·
No sewing start possible
Select another clamping foot
Choose another sewing pattern
Reduce size of sewing pattern in
X-direction
1
· No sewing start possible
· Select another clamping foot
· Choose another sewing pattern
· Reduce size of sewing pattern in
X-direction
· Reduce size of sewing pattern in
Y-direction
· No sewing start possible
· Select another clamping foot
· Choose another sewing pattern
· Reduce size of sewing pattern in
Y-direction
·
·
·
·
No sewing start possible.
Select another clamping foot
Choose another sewing pattern
Reduce size of sewing pattern in both
X- and Y-direction
· No sewing start possible.
· Select another clamping foot
· Choose another sewing pattern
· Reduce size of sewing pattern
X-direction
Reduce Y-Offset in the corresponding
direction
·
·
·
·
No sewing start possible.
Select another clamping foot
Choose another sewing pattern
Reduce Y-Offset in the corresponding
direction
79
Pictogram
Description
seam pattern
exceeds the work
surface opening of
the clamping foot in
X-direction
seam pattern
exceeds the work
surface opening of
the clamping foot in
Y-direction
seam pattern
exceeds the work
surface opening of
the clamping foot in
X/Y-direction
Seam pattern locked
80
Category
Warning
Warning
Warning
Hint
Reaction / Troubleshooting
·
·
·
·
No sewing start possible
Select another clamping foot
Choose another seam pattern
Reduce size of seam pattern in
X-direction
·
·
·
·
No sewing start possible
Select another clamping foot
Choose another seam pattern
Reduce size of seam pattern in
Y-direction
·
·
·
·
No sewing start possible
Select another clamping foot
Choose another seam pattern
Reduce size of seam pattern in
X/Y-direction
·
·
No sewing start possible.
Choose another seam pattern
Unlock seam pattern
8.6.3
Errorcode
Description
Possible cause
1051
Sewing motor timeout
- Cable to sewing motorreference switch faulty
- Reference switch faulty
- Sewing motor faulty
- Mechanical parts
rough-running
- Check cable
Troubleshooting
- Check reference switch
Check sewing motor
- Check the mechanical parts
1052
Sewing motor
overcurrent
- Sewing motor cable faulty
- Sewing motor faulty
- Control faulty
- Software not compatible
to the control unit version
(A/Bxx.x)
-
1053
Sewing motor
overvoltage
Mains voltage too high
Check the mains voltage
1055
Sewing motor
overload
- Sewing motor blocked
/rough-running
- Sewing motor faulty
- Control faulty
- Eliminate blocking/rough-running
Check sewing motor cable
Check sewing motor
Check control
Check the serial number of the
DAC III control unit 1 , if necessary
load the correct software version.
- Check sewing motor
- Check control
1056
Sewing motor
overheat
- Sewing motor rough-running
- Sewing motor faulty
- Control faulty
- Eliminate rough-running
- Check sewing motor
- Check control
1058
1059
Sewing motor speed
(inverted)
Sewing motor faulty
Check sewing motor
1062
Sewing motor IDMA
Autoincrement
Failure
Switch the sewing machine off
and on again
1302
Sewing motor power
source error
- Plug for sewing motor
not plugged in
- Plug for incremental
sensor not plugged in
- Connect the plug for the sewing
motor
- Connect the plug for the
incremental sensor
1342
–
1344
Sewing motor failure
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
2101
Step motor X-Axis
Timeout Referencing
- Cable to
reference switch faulty
- Reference switch faulty
- Step motor faulty
Mechanical part
rough-running
- Check cable
2152
Step motor X-Axis
overcurrent
- Step motor X-Axis
faulty
- Control faulty
- Check step motor X-Axis
- Check control
Step motor X-Axis
overvoltage
Mains voltage too high
Check the mains voltage
2156
Step motor X-Axis
overheat
- Step motor X-Axis
rough-running
- Step motor X-Axis
faulty
- Control faulty
- Eliminate rough-running
Step motor X-Axis
IDMA Autoincrement
Failure
1
- Check reference switch
- Check step motor
- Check the mechanical parts
2153
2162
1
Machine faults (DAC III)
- Check step motor X-Axis
- Check control
Switch the sewing machine off
and on again
Serial numbers 0302-00101 ... 0307-00643: the control unit should be used with an Axx.x-Version
Serial numbers 0307-00644 and higher:
the control unit should be used with an Bxx.x-Version
81
Errorcode
2201
2252
Description
Possible cause
Step motor Y-Axis
Timeout Referencing
- Cable to reference
switch faulty
- Reference switch faulty
- Step motor faulty
- Mechanical part
rough-running
- Check cable
- Step motor Y-Axis
faulty
- Control faulty
- Check step motor Y-Axis
Step motor Y-Axis
overcurrent
Troubleshooting
- Check reference switch
Check step motor
- Check the mechanical part
- Check control
2253
Step motor Y-Axis
overvoltage
Mains voltage too high
Check the mains voltage
2256
Step motor Y-Axis
overheat
- Step motor Y-Axis
rough-running
- Step motor Y-Axis faulty
- Control faulty
- Eliminate rough-running
- Check Step motor Y-Axis
- Check control
2262
Step motor Y-Axis
IDMA Autoincrement
Failure
Switch the sewing machine off
and on again
2911
2914
Step motor error
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
3100
Machine control
voltage
Temporary mains voltage
drop
Fuse F403 faulty
Check the mains voltage
Temporary mains voltage
drop
Fuse F402 faulty
Check the mains voltage
Machine voltage
intermediate circuit
sewing motor
Temporary mains voltage
drop
Fuses F400/F404 faulty
(ext.)*
Check the mains voltage
Machine voltage
intermediate circuit
step motors
Temporary mains voltage
drop
Fuse F401 faulty
Check the mains voltage
Machine temperature
- Vent holes closed
- Check the vent holes
- Ventilation grid dirty
- Clean the ventilation grid
The counter for the hook
thread counter is zero :
the bobbin is empty
Confirm the message and replace
the bobbin.
3101
3102
3103
3107
3215
Machine power
voltage
Machine hook thread
counter zero
Replace fuse F403
Replace fuse F402
Replace fuses F400/F404 (ext.)
Replace fuse F401
* Those fuses could also be faulty when the control unit does not react and/or powering up does nothing!
82
Errorcode
Description
3301
3320
3322
3330
3332
3340
3341
3350
3351
3353
3360
3361
3400
3401
3403
Error control
procedure / Test
procedure / Step
motor test procedure /
Starting procedure /
Sewing procedure /
Winding procedure /
Adjusting aids
3410
Clamping foot not at
the top
Possible cause
Internal error
Troubleshooting
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
- Check the monitoring switch of
the clamping foot (Auto-Input test)
- Check the cable of the switch
(Auto-Input test)
- Check the mechanics
- Check the clearance
- Check the mains voltage
3411
Clamping foot not at
the bottom
- Monitoring switch of the
clamping foot faulty
- Cable of the switch faulty
- Mechanics rough-running
- Distance switch-lug
too big
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
3412
Clamping foot is
already at the bottom
- Monitoring switch of the
clamping foot faulty
- Cable of the switch faulty
- Mechanics rough-running
- Distance switch-lug
too big
- Check the monitoring switch of
the clamping foot (Auto-Input test)
- Check the cable of the switch
(Auto-Input test)
- Check the mechanics
- Check the clearance
- Check the mains voltage
3420
Upper thread burner
not advanced
- Switch of the upper
thread burner faulty
- Cable of the switch faulty
- Upper thread burner
mechanics jammed
- Check the switch
(Auto-Input test)
- Check the cable of the switch
(Auto-Input test)
- Check the mechanics
3421
Lower thread burner
not advanced
- Switch of the lower
thread burner faulty
- Cable of the switch faulty
- Lower thread burner
mechanics jammed
- Check the switch
(Auto-Input test)
- Check the cable of the switch
(Auto-Input test)
- Check the mechanics
3422
Too long preheating
time for the thread
burner
The time t5 is greater than
the sewing time
- Shorten the time t5
- Reduce the sewing speed
83
1
Errorcode
Description
Possible cause
Troubleshooting
3423
Timeout burner heater
The sewing procedure is
due to error interrupted
The burner heater will be switched
off.
Switch the sewing machine off and
on again
3358
Sewing procedure:
Handwheel turned
during interruption
Handwheel turned
manually during sewing
interruption
Cancel the sewing procedure:
Step the pedal backwards
3500
3506
3520
3530
3540
3721
3722
Error Command
Interpreter / Motor
synchronization
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
4301
Dongle missing
No dongle plugged in
Connect the dongle to the control
4302
Dongle empty
No data saved on the
dongle
Save the data on the dongle
4304
Wrong dongle type
The dongle has not the
proper format for the
wished function
- Use other dongle type
- Format dongle
4307
Wrong machine class
The dongle data is not
formatted for the cl. 510
- Use other dongle type
- Format dongle
4311
Error Format-ID
- Dongle not formatted
properly
Dongle faulty
- Format the dongle anew
- Use a new dongle
4312
Unknown dongle type
- Dongle not formatted
properly
- Dongle faulty
- Format the dongle anew
- Use a new dongle
4530
4537
4900
Error menu system /
User log-in
Internal error
Switch the sewing machine off
and on again
Software update
Contact the DA-Service staff
5101
NV-RAM empty
Control is brand new, no
data found
Control is for another
class, incompatible data
Data will be reset to factory setting.
5104
Error NV-RAM
checksum
NV-SRAM faulty
Failure
- Check via Multitest, if necessary
replace the control
Switch the sewing machine off
and on again
Data will be reset to factory setting.
84
Errorcode
Description
Possible cause
Troubleshooting
5804
Free seam patterns:
Wrong checksum
- NV-SRAM faulty
- Failure
- Check via Multitest,
check the control
- Switch the sewing machine off
and on again
Data will be reset to factory setting.
5808
Error free seam
contour
Cannot determine the
stitch number
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
5809
Free seam patterns:
Max. number of seam
pattern parts
Max. number of seam
Delete some intermediate cut in the
pattern parts (intermediate free seam patterns
cut) exceeded
5810
Free seam patterns:
Min. number of stitches
per seam pattern part
Cannot keep the min.
number of stitches per
seam pattern part
Move some intermediate cut in the
free seam patterns
5900
Error sequences –
Invalid sequence
number
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
6151
6154
Error input/output
Internal error
Switch the sewing machine off
and on again
6351
6354
Error I 2 C
Control faulty
- Check control
- Software update
- Contact the DA-Service staff
6551
6554
6651
6653
6751
6761
6952
Error
Machine head
position /
AD-Converter /
Processor error / Step
motor driver
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
7451
7453
7454
Communication Test
Interface
Internal error
Switch the sewing machine off
and on again
7452
7455
Communication Test
Interface
- Transmission failure
- Cable Test interface
faulty
- Internal error
- Switch off the source of
interference
- Check cable
- Switch the sewing machine off
and on again
7551
7555
7558
7559
Communication
Terminal interface
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
7556
7557
Communication
Terminal interface
- Transmission failure
- Cable Terminal interface
faulty
- Switch off the source of
interference
- Check cable
7700
Protocol: Max number
of repetition
- Transmission failure
- Cable Test interface
faulty
- Switch off the source of
interference
- Check cable
1
85
Errorcode
Description
Possible cause
Troubleshooting
7701
Error Protocol
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
8151
8156
8159
Error IDMA
- Failure
- Control faulty
- Switch the sewing machine off
and on again
- Replace control
8152
8154
8251
8255
Error IDMA / Booting
ADSP / Booting
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
8252
8257
8258
/
8253
8256
8254
Booting ADSP /
Booting XILINX /
Booting
Failure
- Switch the sewing machine off
and on again
8351
8700
8702
8800
8806
8890
8891
Error Testpins / Key
simulation / Signals /
Event processing /
Memory-Wrapper /
List of functions
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
9100
9105
9200
9201
9900
9902
9903
9905
Error seam pattern
administration / seam
pattern program /
seam pattern release /
Equipment / Key
processing / Memory
Output Message
Internal error
- Switch the sewing machine off
and on again
- Software update
- Contact the DA-Service staff
9906
Error monitoring
switch clamping foot
- Switch faulty
- Cable faulty
- Distance switch-lug
too big
If the error 9100 appears
repeatedly, go through the
initialization menu and reset the
seam pattern programs and
sequences (compare to page 62).
- Check the switch
- Check the cable
- Check the clearance
After troubleshooting set the
machine parameters to the factory
settings, so that the switch can be
recognized again (compare to page
62).
Should an error occurs, the corresponding component can be checked
over the menu service/multi-test for its correct function (compare to
page 49). The service menu can be reached by switching to the
”Technician mode" or by pressing the key F when switching on the
machine (enter the code number “25483").
86
9.
Sewing
Operating and function sequence when sewing:
Sewing operation
Before the sewing
start
Starting position
Operation/ Explanation
- Pedal in resting position
Automatic bartacker stands idle
Needle and clamping foot in position “up”.
Feed material
Sewing
During the sewing
cycle
Interrupt sewing
operation
Continue sewing
operation
- Step pedal forwards up to step 1.
The clamping foot is lowered.
- Relieve pedal.
The clamping foot is lifted again.
The material can be positioned anew.
- Step pedal completely to the front.
The automatic bartacker sews with the
adjusted speed.
1
- Step pedal backwards.
The automatic bartacker stops.
The clamping foot stays down.
- Step pedal completely to the front.
87
10. Maintenance
10.1 Cleaning and checking
Caution: Danger of injury !
Switch off main switch.
The maintenance of the automatic bartacker must only be carried
out if the machine is switched off.
Maintenance work has to be done after the intervals indicated in the
tables at the latest (see column “Operating hours”).
The processing of fluffy material may require shorter maintenance
intervals.
A clean automatic bartacker protects from disturbances.
1
2
Maintenance work
to be done
Explanation
Operating
hours
Machine head
- Remove sewing dust and thread
remainders.
(e.g. with compressed air pistol)
Spots to be cleaned especially carefully:
- Underside of the throat plate
- Zone around hook 1
- Bobbin case
- Thread trimmer
- Zone around needle 2
8
Control box
Keep free the ventilation grilles.
8
88
10.2 Oil lubrication
3
2
1
1
Caution: Danger of injury !
Oil can cause skin eruption.
Avoid a longer contact with the skin.
Wash yourself thoroughly after a contact.
ATTENTION !
The handling and disposal of mineral oils is subject to legal
regulations.
Deliver used oil to an authorized collecting station.
Protect your environment.
Be careful not to spill any oil.
Oil the automatic bartacker exclusively with lubricating oil DA-10 or an
equivalent oil with the following specification:
– Viscosity at 40° C:
10 mm 2 /s
– Ignition point:
150° C
DA-10 can be bought at the sales points of
DÜRKOPP-ADLER AG under the following parts numbers:
250-ml-Container:
9047 000011
1-Litre-Container:
9047 000012
2-Litre-Container:
9047 000013
5-Litre-Container:
9047 000014
Maintenance work
to be done
Lubrication of the automatic
bartacker
Explanation
The automatic bartacker is equipped with a
central oil wick lubrication. The bearings are
provided by the oil reservoirs 2 and 3.
Operating
hours
8
- The oil level must not drop below the red
marking of the two oil reservoirs.
- Fill up oil up to the red marking through
drill-hole 1.
89
11. Standard seam patterns
Bartack
type
large
straight
bartack
90
No.
Stitch diagram
Number of Sewing dimensions
stitches
(mm)
X
Y
Clamping foot
No.
1
42
16
2,0
1, 2
2
42
10
2,0
1, 2
3
42
16
2,5
1, 2
4
42
24
2,5
3
5
28
10
2
1, 2
6
28
16
2,5
1, 2
7
36
10
2
1, 2
8
36
16
2,5
1, 2
Bartack
type
No.
Stitch diagram
Number of Sewing dimensions
stitches
(mm)
X
Y
Clamping foot
No.
9
56
24
3
3
10
64
24
3
3
11
21
6
2,5
4, 8
large
straight
bartack
1
12
28
6
2,5
4, 8
13
36
6
2,5
4, 8
14
15
8
3
4
15
21
8
2
4
16
28
8
2
4
small
straight
bartack
91
Bartack
type
No.
Stitch diagram
Number of Sewing dimensions
stitches
(mm)
X
Y
Clamping foot
No.
17
21
10
0
1, 2
18
25
10
0
1, 2
19
27
25
0
3
20
36
25
0
3
21
41
25
0
3
22
43
35
0
7
23
29
4
20
5
24
41
4
20
5
rectilinear
straight
bartack
Longitudinal
bartack
92
Bartack
type
No.
Stitch diagram
Number of Sewing dimensions
stitches
(mm)
X
Y
Clamping foot
No.
25
48
4
20
5
26
56
4
20
5
27
18
0
20
5
28
21
0
10
5
29
21
0
20
5
30
27
0
10
5
31
29
12
12
9
32
52
12
12
9
Longitudinal
bartack
1
rectilinear
longitudinal
bartack
circular
bartack
93
Bartack
type
No.
Stitch diagram
Number of Sewing dimensions
stitches
(mm)
X
Y
Clamping foot
No.
circular
bartack
33
76
12
stitched
eyelet
34
101
outer Ø 9
inner Ø 3
35
42
10
7
10
36
57
10
7
10
37
42
10
7
12
38
57
10
7
12
39
42
10
7
12
40
57
10
7
12
12
9
9
D-bartack
94
Bartack
type
No.
Stitch diagram
Number of Sewing dimensions
stitches
(mm)
X
Y
Clamping foot
No.
41
42
7
10
11
42
57
7
10
11
43
42
7
10
11
44
57
7
10
11
45
102
19
2,6
3
46
120
20
3,8
3
47
47
17
10
6
48
103
40
20
7
D-bartack
imitated
buttonhole
bartack
1
cross
bartack
95
Bartack
type
No.
Stitch diagram
Number of Sewing dimensions
stitches
(mm)
X
Y
Clamping foot
No.
49
44
12
10
13
50
44
12
10
13
Tri-bartack
96
20,0 x 4,5
yes
1
all
Straight bartack
Standard equipment
Cl. 510-211
2
21,0 x 5,1
yes
1
all
Straight bartack
Standard equipment
Cl. 510-213
3
27,0 x 5,0
yes
4
all
Straight bartack, large
Optional
4
10,0 x 4,5
yes
2
all
Straight bartack, small
Optional
5
5,6 x 23,0
yes
23
all
Longitudinal bartack
Optional
6
19,0 x 12,0
yes
47
all
Small field clamping foot
Optional
7
44,0 x 24,0
yes
48
all
Large field clamping foot
Optional
8
9,5 x 4,5
yes
11
all
Contraction clamp
Standard equipment
Cl. 510-212
9
16,0 x 16,0
no
31
10
12,0 x 14,0
no
35
11
24,6 x 12,6
no
12
12,6 x 21,0
13
31, 32, 33, 34 Circular
35, 36
Comment
Description
Allowed
standard seam
patterns
Specified standard
seam pattern number
Dimensions X x Y [mm]
1
Inner frame,
rectangular
Clamping foot number
12. Clamping feet
Optional
D-clamping foot, simple
Optional
41
14, 42, 43, 44 Double D-clamping foot
lateral
Optional
no
37
37, 38, 39, 40 Double D-clamping foot,
longitudinal
Optional
34,8 x 12,2
no
49
49, 50
14
16,0 x 2,6
yes
1
all
15
-
yes
-
-
16
8,6 x 13,6
no
41
Double Tri-clamping foot
lateral
Optional
Straight bartack
Optional
Blank clamping foot
Optional *
41, 42, 43, 44 Double-D-clamping foot
lateral large
1
Optional
*
Clamping foot number not selectable. Please define the size in free
seam patterns.
Important:
When using clamp feet with bridge (for example Double D-clamping
foot lateral, self made clamping feet) the clamp lifting stroke must be
reduced, so that the needle does not collide against the bridge when
checking the reference positions (see Service Instructions Chap. 6.4)
97
13. Numbering of menu items
Parameter
English (displayed on the screen)
English (meaning)
0
off/a
off/a
1
on/b
on/b
D01
yes
yes
D02
no
no
D03
canc
cancel
D04
ok
OK
Q01?
Initialize variants and
sequencesquestion
Initialize variants and sequencesquestion
Q02?
Initialize machine
Initialize machine
Q03?
Initialize free seam patternsquestion
Initialize free seam patternsquestion
Q04?
Initialize machine complete?
Initialize machine complete?
Q05?
continue?
continue?
T1
machine
machine
T1.1
parameter
parameter
T1.1
PWM output test
PWM output test
T1.1.1
cut.rpm
cutting speed
T1.1.2
max.rpm
maximum sewing speed
T1.1.3
stop pos.
stop position
T1.1.4
sew.st.pt.
sewing start position
T1.1.5
ref.freq.
referencing frequency
T1.2
soft start
soft start
T1.2.1
1.stitch
1.stitch
T1.2.2
2.stitch
2.stitch
T1.2.3
3.stitch
3.stitch
T1.2.4
4.stitch
4.stitch
T1.2.5
5.stitch
5.stitch
T1.3
equipment
equipment
T1.3.1
w.clamp f.
working clamp foot
T1.3.2
open dimens.
open dimensions
T1.3.3
number
number
T1.3.4
length
length
T1.3.5
width
width
T1.3.6
configuration
configuration
T1.3.6.1
hand sw.
hand switch
T1.3.6.2
el.wiper
electrical wiper
T1.3.6.3
_/-clamp
separated clamp foot
T1.3.6.4
laserl.
laserlights
T1.3.6.5
th.burner
thread burner
T1.3.6.6
opt.signalling
optical signalling
T1.3.6.6.1
opt.sign.
optical signalling
T1.3.6.7
input alloc.
input allocation
98
Parameter
English (displayed on the screen)
English (meaning)
T1.3.6.8
output alloc.
output allocation
T1.3.6.9
l.ta cfs
long ta clamp foot solenoid
T1.4
times
times
T2
user settings
user settings
T2.1
language
language
T2.2
sewing mode
sewing mode
T2.2
hand switch
hand switch
T2.3
par.lock.
parameter locking
T2.4
pattern lock.
pattern locking
T2.5
sequence lock.
sequence locking
T2.6.1
lock all
lock all
T2.6.2
unlock all
unlock all
T2.7.1
lock all
lock all
T2.7.2
unlock all
unlock all
T3
service
service
T3.1
multitest
multitest
T3.1.1
output test
output test
T3.1.2
PWM output tst
PWM output test
T3.1.3
input test
input test
T3.1.4
auto input test
auto input test
T3.1.5
motor test
motor test
T3.1.6
step.motor tst
stepping motor test
T3.1.6
step.motor tst
stepping motor test
T3.1.7
RAM test
RAM test
T3.1.8
EEPROM test
EEPROM test
T3.2
180 °-disc
180 °-disc
T3.3
events
events
T3.3.1
event memory
event memory
T3.3.1
event memory
event memory
T3.3.2
latest events
latest events
T3.3.2
latest events
latest events
T3.4
DACIII
DACIII
T3.4.1
temp.(°C)
temperature (°C)
T3.4.2
UZK (V)
UZK (V)
T3.5
Init
Init
T3.5.1
event memory
event memory
T3.5.2
var.+sequ.
variants + sequences
T3.5.3
mach.+usr+opt
machine + user + options
T3.5.4
free seam patterns
free seam patterns
T3.5.5
machine cpl.
machine complete
T4
free seam patterns
free seam patterns
T4.1
design
design
1
99
Parameter
English (displayed on the screen)
English (meaning)
T4.1.7
append stitch
append stitch
T4.1.8
parameter
parameter
T4.1.8.1
std.rpm
standard speed
T4.1.8.2
orig. X
origin X
T4.1.8.2
dist. X
distance X
T4.1.8.3
orig. Y
origin Y
T4.1.8.3
dist. Y
distance Y
T4.1.8.4
end
end
T4.2
edit
edit
T4.2.1
stitch coordin
stitch coordinates
T4.2.2
del.st
delete stitch
T4.2.3
ins.st.
insert stitch
T4.2.4
append stitch
append stitch
T4.2.5
parameter
parameter
T4.2.5.1
std.rpm
standard speed
T4.2.5.2
orig. X
origin X
T4.2.5.2
dist. X
distance X
T4.2.5.3
dist. Y
distance Y
T4.2.5.3
orig. Y
origin Y
T4.2.6
no.stitch
number of stitches
T4.2.7
no.st.av.
number stitches available
T4.3
delete
delete
T4.4
copy
copy
T4.5
no.st.av.
number stitches available
T4.6
no.pat.av.
number patterns available
T5
memory dongle
memory dongle
T5.1
dongle index
dongle index
T5.2
load
load
T5.2.1
dongle index
dongle index
T5.2.2
machine cpl.
machine complete
T5.2.3
free seam pattern
free seam pattern
T5.3
save
save
T5.3.1
dongle index
dongle index
T5.3.2
machine cpl.
machine complete
T5.3.3
free seam pattern
free seam pattern
T5.4
format
format
T5.4.1
data dongle
data dongle
T5.4.2
boot dongle
boot dongle
W01
code
code
W02
WARNING
WARNING
W03
ERROR
ERROR
W04
INFORMATION
INFORMATION
100
Parameter
English (displayed on the screen)
English (meaning)
W05
EMERGENCY-OFF
EMERGENCY-OFF
W06
SERIOUS ERROR
SERIOUS ERROR
W07
NOTE
NOTE
W08
INTERNAL ERROR
INTERNAL ERROR
W09
CONFIRMATION
CONFIRMATION
W10
read data
read data
W11
save data
save data
W12
format
format
Z01
output
output
Z02
input
input
Z03
rpm
rpm
Z04
stop pos.
stop position
Z05
software
software
Z06
date
date
Z07
e
e
Z08
please wait
please wait
Z09
ROM size
ROM size
Z10
class
class
Z11
version
version
Z12
check sum
check sum
Z13
error code
error code
Z14
pedal
pedal
Z15
hand sw.
hand switch
Z16
laserl.
laserlights
Z17
_/-Klamm
separated clamp foot
Z18
opt.sign.
optical signalling
Z19
not alloc.
not allocated
Z20
Subclass
subclass
1
101
Download PDF