Eclipse | AVX5000 | Owner`s manual | Eclipse AVX5000 Owner`s manual

OWNER'S MANUAL
AVX5000
"DVD/MS Multi-Source Receiver with 7" Wide TFT Display"
We appreciate your purchase of this receiver.
Please read through this manual for correct operation.
We suggest that after reading it you keep this manual
in a safe place for future reference.
Warnings and cautions signs, illustrated below, are posted throughout this manual as well as
on the device itself. They show safe and correct ways to handle the product so as to prevent
personal injury to you and others, and to avoid damage to property. Before reading through
the manual, take time to read through and learn the important information listed in this section.
Cautions for use
* The images appearing on the screen may differ from those shown in this manual
depending on the type of database used and when it was created.
Warning
This sign indicates a situation in which incorrect handling
through disregard of a sign might result in death or serious
personal injury.
Caution
This sign indicates a situation in which incorrect handling
through disregard of a sign might result in personal injury or may
result solely in damage to property.
The symbol shown below indicates important instructions or helpful information to keep in
mind.
A point it will be helpful to remember.
Important points.
● Please read all materials that come with the product, such as manuals and warranties.
Eclipse will not be liability for unsatisfactory product performance due to failure to follow
these instructions.
● Changes in product specifications may result in differences between the content of the
manual and actual product features.
Please use care in handling the manual.
Forcefully spreading or pulling on pages may result in their falling out of the binding.
Use the manual carefully.
1
●Do not modify this system for use other than that specified herein. Also, do not
deviate from the installation procedures described herein; Eclipse will not be held
liable for damages including, but not limited to serious injury, death or property
damage resulting from installations that enable unintended operation.
●This equipment requires 12V DC and should only be installed in a vehicle with a
12V negative ground electrical system. Any other installation may cause a fire or
other severe damage to the equipment and the vehicle.
●Never install this equipment where it will interfere with safe operation of the
vehicle. Never block the drivers’ view. Do not install equipment where it may
interfere with operation of the brakes, the steering or any safety equipment,
including seat belts and air bags.
●Before to drilling holes in a vehicle for installation, you must confirm the locations
of pipes, tanks, electrical wiring, and other vehicle systems and components to
ensure that there will be no interference or contact. In addition, addition, it is
necessary apply rust prevention and leak prevention measures at the drilling
area. Otherwise, fire or electric shock could occur.
●When installing equipment do not remove or alter existing vehicle fasteners,
including nuts, bolts, screws, clips, and fittings. Never detach, move or alter
existing vehicle wiring, including electrical grounds and straps. Alteration of
existing vehicle components may make vehicle unsafe to operate.
●Before installation, remove the negative (-) battery terminal to prevent shocks,
electrical arcing, fires, and damage to vehicle wiring and the equipment you are
installing.
●Secure wiring with tape or plastic ties so that wires do not interfere with vehicle
operation, including brake pedal, gear shifter and steering. Position wires so that
they will not be rubbed, abraded, or damaged by moving vehicle components,
including power seats.
●To avoid equipment and vehicle damage, including fire, never supply power to
installed equipment in a way which will overload the capacity of an existing
vehicle circuit. Never leave a power supply wire or connection uninsulated.
Always install supplied fuses, circuit breakers, and relays.
●Air bags are vital safety equipment. Never install equipment in a way which will
alter air bag wiring or interfere with air bag deployment. Air bags must function
properly in the event of an accident.
●When installation is complete, test all vehicle electrical systems for proper
operation, including lights, horn, brake lights, and emergency flashers.
●For your protection, never use a power drill without safety glasses or goggles.
Debris or broken drill bits may cause severe eye injuries, including blindness.
●Use electrical tape to insulate the ends of all wires, even if not used. Proper
insulation prevents arcs, shocks and fires.
2
●Do not damage the camera cable. Any holes in the camera will provide a point of
entry for moisture and water, which may cause malfunctions, fire or electric
shock.
●Some equipment uses batteries. Never install equipment where young children
can get access to batteries. If a battery is swallowed, seek medical attention
immediately.
●When vehicle is moving, never take your eyes off the road to make adjustments
to the equipment. You must pay attention to the road to avoid accidents, do not
let the operation or adjustment of the equipment distract you from proper vehicle
operation.
●The driver should never watch video or television while driving. Displays and
screens should never be used or installed where they can be seen by and
possibly distract the driver. It is against the law in many places to have video or
television screens used where they can be seen by the driver. Driving and
watching video or television is an extremely dangerous thing to do.
●The driver should not look at the screen while driving. Accidents may result if you
are not paying attention to the forward direction.
●DO NOT look at the monitor screen while reversing the vehicle. The rear monitor
is merely to assist in confirming the locations of obstacles, and therefore there is
a limit to the visual range that it provides. Be sure to visually check for safety
while reversing the vehicle. Otherwise, you may hit a person or object in the blind
spot of the camera, resulting in a serious accident.
●Drive slowly while reversing the vehicle. The rear monitor uses a wide angle
lens, and the actual distance is different than how it appears. If you reverse the
vehicle at high speed, you may hit a person or object, resulting in a serious
accident.
●Do not put foreign objects in the loading slot of Memory Stick Duo or disc. Fires
or shocks may result.
●Do not disassemble or alter this equipment. Accidents, fires or shocks may
result.
●Do not let water, dust or foreign objects enter the internal parts of this equipment.
Smoke, fires or shocks may result.
●Pay attention to where the remote control is left. Traffic accidents or problems
with driving may result if the remote control makes its way under the foot pedals
etc. when the vehicle is stopped or when it goes around a corner.
●Do not use when it is broken (the screen is not lit or no sound comes out).
Accidents, fires or shocks may result.
3
●Always replace fuses with fuses of identical capacity and characteristics. Never
use a high capacity fuse than the original. Using the wrong type of fuse may
cause a fire or severe damage.
●If foreign objects or water enters the equipment, smoke comes out, or there is a
strange odor, stop using it immediately, and contact your dealer. Accidents, fires,
or shocks may result if you continue to use it in these conditions.
●The driver should not change the Memory Stick Duo or CD while driving. As
accidents may result if you are not paying attention to the forward direction, first
stop the car at a safe location and then proceed.
●Plastic bags and wrappings may cause suffocation and death. Keep away from
babies and children. Never put bag over your head or mouth.
●Wiring and installing this equipment requires expertise and experience.
Professional installation is recommended. Consult with your dealer or a
professional installer. Incorrect wiring may damage the equipment or interfere
with safe vehicle operation.
●Use only the accessory parts as specified. Using other parts may cause damage
to the equipment or cause parts to fall or fly off the equipment.
●Do not install the unit in places where it may get dew condensation on (around
the air conditioning hose, etc.), come in contact with water, or in condition of high
moisture, dust or oily smoke. If water, moisture, dust or oily smoke enters this
unit, smoke, fires or malfunctions may result.
●Avoid installing in places where it cannot be fastened securely or where there are
strong vibrations. Also, if you installed the unit with double-sided tape, first wipe
away dirt and wax from the installation area. Otherwise, the unit may come loose
due to vibration while driving, causing problems for driving and resulting in traffic
accidents or injuries.
●Do not install in places with direct sunlight or where it will be hit directly by hot air
from the heater. This may increase the temperature of the interior of this
equipment, resulting in fires and malfunctions.
●Chose the installation location carefully so that the unit is not installed so that it
can contact pedestrians and injure them.
●Do not install the television antenna in hard-to-install, unstable places, or on
easily peeled surfaces that have been treated with fluorine resin or water
repellent. Accidents may result if the antenna comes off while the can is
traveling, falls or makes contact with pedestrians.
4
●When installing a TV antenna on the trunk or similar location, be careful of the tip
of the TV antenna when opening and closing the trunk. Otherwise, it could cause
injury to eyes, etc.
●Tighten the fasteners for the antenna securely so that it will not vibrate loose and
injure a pedestrian or cause an accident.
●Occasionally check the camera installation screws, and tighten any that are
loose. If a screw falls out, it could come into contact with a pedestrian or cause
an accident.
●Be careful when driving into parking garages, under elevated structures, etc.
when the television antenna extends above vehicle height. Accidents may result
if the television antenna makes contact with the elevated structure, breaks off
and falls or makes contact with pedestrians.
●Be careful of the tip of the antenna when opening and closing the trunk if the
television antenna is installed on the trunk. Eye damage or other injuries may
result.
●Do not block the fan, heat sink or vents of this unit. When fan, heat sink or vent is
blocked, the interior overheats, and fires may result.
●Carry out the wiring such that cords are not pinched by movable parts such as
seat rails, and screw parts of the vehicle body. Accidents, fires and shocks may
result from disconnection and electrical shorts.
●Carry out the wiring such that the cord does not make contact with metal parts.
The cord maybe be damaged by contact with metal parts, resulting in fire and
shocks.
●Avoid hot surfaces when wiring equipment. High temperatures may damage
wiring, causing shorts, arcing and fires.
●Seal the antenna lead and other wires into the vehicle body to prevent rain and
water from entering the vehicle. Water leaks may cause shorts and fires.
5
●When changing the installation location for this equipment, please consult the
dealer where you bought it for safety reasons. Expertise is necessary for removal
and installation.
●Keep volume to a reasonable level so that you can hear sounds from outside the
vehicle, including warning sounds, voices, and sirens. Failure to do so may
cause an accident.
●Be careful that hands and fingers are not pinched when adjusting the tilting angle
or closing display. Injuries may result.
●Do not put your hands or fingers into the loading slot of Memory Stick Duo or
disc. Injuries may result.
●Do not touch the heat dissipating part of the amp. Burns may result from the heat
of this part.
●Avoid immersing the camera in water or passing it through automated (high
pressure) car washing machines. Otherwise, water will get inside the camera or
the camera may fall off, resulting in an accident.
●Do not recharge dry batteries. Dry batteries may rupture, resulting in injuries.
●Do not use batteries other than those specified. Also, do not mix old and new
batteries. Injuries or pollution to the surroundings may result from battery
ruptures and leakage.
●When inserting batteries into the equipment, be careful with the polarity (positive/
negative), and insert them as indicated. If the battery polarities are incorrect,
injuries and pollution to the surroundings may result from battery ruptures and
leakage.
●Replace used batteries as soon as possible; they may leak and damage
equipment. Battery leakage can burn your skin or your eyes. Wash hands after
handling.
●If alkaline solution from alkaline dry batteries makes contact with your skin or
clothes, flush with clean water. If any of the solution gets in your eyes, also flush
clean with water and then seek medical attention.
●When disposing of lithium dry batteries, affix insulating tape to the positive and
negative terminals, and after they are insulated, dispose of them according to the
"Local municipal ordinances". Shorts, fires and ruptures may result from disposal
when coming contact with other electrically conductive objects such as metal
parts, etc.
●Do not short, disassemble or heat the batteries, or place them in fire or water.
Fire and injuries may result from battery rupture and leakage.
●Store the remote control in a place away from direct sunlight, high temperatures,
and high moisture levels. The case may change shape, and the batteries may
rupture and leak.
6
●Do not use this equipment except for in-vehicle use. Shocks or injuries may
result.
●Be careful of the position of the volume when turning the power source ON.
Hearing damage may result if very loud noise is emitted when the power is
turned ON.
●The image from the rear monitor is the same image from the rearview mirror and
side mirrors, with the left and right sides reversed. In addition, the view is
different depending upon the type of vehicle. Pay careful attention.
●Do not operate under abnormal conditions such as when the sound is broken or
distorted. Fires may result.
●This equipment uses invisible laser light. Do not disassemble or alter this
equipment. If trouble occurs, contact the dealer where you bought the
equipment.
Altering this equipment may cause exposure to laser emissions (worsening
eyesight), or result in accidents, fires or shocks.
●If the equipment is dropped or the cosmetics appear broken, turn off the power to
the main unit and contact your dealer. If used in this condition, fires or shocks
may result.
7
8
Table of Contents
Introduction ............................................................................................... 24
I
Basic operation ......................................................................................... 40
II
How to operate the tuner.......................................................................... 80
III
How to operate the CD player .................................................................. 87
IV
How to operate the MP3/WMA player...................................................... 92
V
How to operate the optional CD changer.............................................. 103
VI
How to operate the DVD player.............................................................. 106
VII
How to operate the video CD player (Asia only) .................................. 129
VIII
How to operate the Area Shot function (U.S.A./CANADA only).......... 134
IX
ESN security operating procedure ........................................................ 149
X
How to use the remote control .............................................................. 165
XI
How to operate the optional 5.1ch decoder & AV selector unit.......... 170
XII
How to operate the optional HD radio tuner (U.S.A. only) .................. 202
XIII
How to operate the optional SIRIUS satellite radio tuner
(U.S.A. only) ... 208
How to operate the optional TV tuner
(U.S.A./CANADA/KOREA/TAIWAN only). ... 214
XIV
How to operate the VTR.......................................................................... 219
XVI
How to operate the Back-eye Camera................................................... 222
XVII
For reference ........................................................................................... 226
XVIII
Before installation................................................................................... 247
XIX
Mounting instruction .............................................................................. 248
XX
XV
9
Introduction
How to use this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Before using the deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
About discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
About supported disc types . . . . . . . . . . . . . . . . . . . . . . . . . .
About handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About new discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About rental discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About specially shaped discs. . . . . . . . . . . . . . . . . . . . . . . . .
About disc accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the “Memory Stick Duo” . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
32
33
33
33
33
34
About supported “Memory Stick Duo” types . . . . . . . . . . . . 34
About handling the “Memory Stick Duo” . . . . . . . . . . . . . . . 35
About the LCD panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
About TV (U.S.A./CANADA/KOREA/TAIWAN only). . . . . . . . . . . . . 36
Name of controls and parts . . . . . . . . . . . . . . . . . . . . . . . . . 37
Panel buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Touch switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Basic operation
How to turn the power ON or OFF . . . . . . . . . . . . . . . . . . . . 40
Turning the power on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Display open/tilt/close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Opening the display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Adjusting the angle of the display . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Switching the display’s pull-out positions . . . . . . . . . . . . . . . . . . . 43
Closing the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Setting the display AUTO CLOSE function . . . . . . . . . . . . . . . . . . . 45
Inserting/Ejecting the disc or “Memory Stick Duo”. . . . . . 46
How to insert disc (CD/DVD) and “Memory Stick Duo” . . . . . . . . . 46
Inserting disc (CD/DVD) or “Memory Stick Duo” . . . . . . . . . 46
10
How to eject disc (CD/DVD) or “Memory Stick Duo” . . . . . . 48
Switching source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Switching the source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Switching source using panel buttons . . . . . . . . . . . . . 49
Switching source using touch switches . . . . . . . . . . . . 50
Operational screen for each source . . . . . . . . . . . . . . . . . . 51
Adjusting the volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Adjusting the main volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Adjusting main volume using touch switches . . . . . . . 52
Adjusting main volume using panel buttons. . . . . . . . . 52
Adjusting sound quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Displaying the sound adjustment screen . . . . . . . . . . . . . . . . . . . . 53
Setting Circle Surround II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Setting CS II TruBass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Adjusting PEQ (parametric equalizer) . . . . . . . . . . . . . . . . . . . . . . . 56
Adjusting/Saving a PEQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Selecting a PEQ pattern from memory . . . . . . . . . . . . . . . . . 57
Adjusting POS (Positioning selector) . . . . . . . . . . . . . . . . . . . . . . . 58
Setting the balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Setting LOUDNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Setting the harmonizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Simplified time alignment settings (Time Alignment) . . . . . . . . . . 61
Selecting the type of vehicle (Car Type) . . . . . . . . . . . . . . . .
Tweeter settings (Tweeter) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear speaker position selection (Rear SP) . . . . . . . . . . . . . .
Setting sub woofer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
62
62
63
Phase selection (NON-F Phase) . . . . . . . . . . . . . . . . . . . . . . .
Woofer output setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crossover adjustment (X-Over) . . . . . . . . . . . . . . . . . . . . . . .
Woofer output level adjustment . . . . . . . . . . . . . . . . . . . . . . .
63
64
64
65
Setting background screen . . . . . . . . . . . . . . . . . . . . . . . . . 66
Setting the Background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Importing Background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Adjusting/setting the screen . . . . . . . . . . . . . . . . . . . . . . . . 69
Switching the FUNCTION switch display. . . . . . . . . . . . . . . . . . . . . 69
Changing the clock settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
11
Setting the clock display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Adjusting the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Adjusting image quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Switching screen mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Setting the steering switch function . . . . . . . . . . . . . . . . . . . . . . . . 74
Reading steering switch data . . . . . . . . . . . . . . . . . . . . . . . . . 75
Compatibility with various switches . . . . . . . . . . . . . . . . . . . 76
Setting the Guide tone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Displaying Amplifer Status (E-AMP) . . . . . . . . . . . . . . . . . . . . . . . . 78
Screen lock settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
How to operate the tuner
How to use the AM/FM radio . . . . . . . . . . . . . . . . . . . . . . . . 80
Listening to the AM/FM radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Listening to the radio using touch switches . . . . . . . . . 80
Listening to the radio using panel button . . . . . . . . . . . 80
Switching the band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Selecting radio stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Manual selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selection using preset switches . . . . . . . . . . . . . . . . . . . . . .
Saving radio stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
81
81
82
Saving manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving with ASM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing stations saved by ASM . . . . . . . . . . . . . . . . . . . . .
Checking preset stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
82
82
83
Creating a station name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Deleting a previously created station name . . . . . . . . . . . . . . . . . . 85
Turning off the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
How to operate the CD player
How to use the CD player. . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Listening to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Listening to a CD using the touch switches . . . . . . . . . 87
Listening to a CD using the panel buttons . . . . . . . . . . 87
12
Selecting a track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Fast-forwarding/rewinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Repeating a track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Playing tracks in random order . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Creating a title for a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Deleting a previously created title . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Displaying CD TEXT by scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Turning off the CD player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
How to use the MP3/WMA player
How to use the MP3/WMA player . . . . . . . . . . . . . . . . . . . . 92
Playing MP3/WMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Playing MP3/WMA using the touch switches. . . . . . . . . 93
Playing MP3/WMA using the panel buttons. . . . . . . . . . 93
Selecting a music file. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Selecting with file change switches. . . . . . . . . . . . . . . . . . . . 94
Selecting with TUNE/TRACK button . . . . . . . . . . . . . . . . . . . 94
Selecting a folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Fast-forwarding/rewinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Changing display of the current level . . . . . . . . . . . . . . . . . . . . . . . 95
Displaying the current level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Repeating the same music file or folder . . . . . . . . . . . . . . . . . . . . . 96
Repeating the same music file . . . . . . . . . . . . . . . . . . . . . . . . 96
Repeating the same folder . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Playing music files in random order . . . . . . . . . . . . . . . . . . . . . . . . 97
Playing music files on folder in random order . . . . . . . . . . . 97
Playing music files on CD in random order . . . . . . . . . . . . . 97
Turning off the MP3/WMA player . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
About MP3/WMAs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Playable MP3 file standards . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Playable WMA file standards . . . . . . . . . . . . . . . . . . . . . . . . . 98
ID3/WMA tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Format of discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
File names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Multi-sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Playing MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
MP3/WMA playing time display . . . . . . . . . . . . . . . . . . . . . . 101
Display order of MP3 file/folder names . . . . . . . . . . . . . . . . 101
Making and playing MP3/WMA files . . . . . . . . . . . . . . . . . . . . . . . . 102
13
Downloading MP3/WMA music from internet . . . . . . . . . . .
Converting CD music to MP3/WMA files . . . . . . . . . . . . . . .
When writing to CD-R/RW . . . . . . . . . . . . . . . . . . . . . . . . . . .
When playing back CD-R/RW . . . . . . . . . . . . . . . . . . . . . . . .
102
102
102
102
How to operate the optional CD changer
How to use the CD changer . . . . . . . . . . . . . . . . . . . . . . . . 103
Listening to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Listening to a CD using the touch switches . . . . . . . . 103
Listening to a CD using the panel buttons . . . . . . . . . 103
Selecting a track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Fast-forwarding/rewinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Selecting a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Repeating a track or CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Repeating the current track . . . . . . . . . . . . . . . . . . . . . . . . . 104
Repeating the current CD . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Playing tracks in random order . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Playing tracks on current CD in random order . . . . . . . . . . 105
Playing tracks on all CDs in random order . . . . . . . . . . . . . 105
Creating a title for a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Deleting a previously created title . . . . . . . . . . . . . . . . . . . . . . . . . 105
Turning off the CD changer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
How to operate the DVD player
Before using the DVD player . . . . . . . . . . . . . . . . . . . . . . . 106
DVD video characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
About multiple languages . . . . . . . . . . . . . . . . . . . . . . . . . . .
About multiple angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
106
107
107
About playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About region codes of playable discs . . . . . . . . . . . . . . . . .
About marks displayed on discs . . . . . . . . . . . . . . . . . . . . .
About DVD disc structures . . . . . . . . . . . . . . . . . . . . . . . . . .
107
108
108
109
How to use the DVD player . . . . . . . . . . . . . . . . . . . . . . . . 110
Watching a DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Watching a DVD using the touch switches . . . . . . . . . 110
14
Watching a DVD using the panel buttons . . . . . . . . . . 111
Waching a DVD using the remote control . . . . . . . . . . 111
Operating the video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Playing the video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing the video using the touch switches . . . . . . . .
Playing the video using the remote control. . . . . . . . .
Fast-forwarding/rewinding . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast-forwarding/rewinding using the
panel buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast-forwarding/rewinding using the
touch switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast-forwarding/rewinding using the
remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repeating a chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pausing the video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pausing the video using the touch switches. . . . . . . .
Pausing the video using the remote control . . . . . . . .
Playing back in slow motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
112
112
112
112
Stopping the video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stopping the video using the touch switches . . . . . . .
Stopping the video using the remote control . . . . . . .
Operating the disc menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
115
115
116
112
112
113
114
114
114
114
114
Operating disc menu using the touch switches . . . . . 116
Operating disc menu using the remote control . . . . . 116
Turning off the DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Turning off the DVD using the panel buttons . . . . . . . 117
Turning off the DVD using the remote control . . . . . . 117
Searching for a desired chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Searching by chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Serching by chapter using the panel buttons . . . . . . . 118
Switching screen display/audio . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Changing the angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching subtitle language . . . . . . . . . . . . . . . . . . . . . . . . .
Switching dubbed audio language. . . . . . . . . . . . . . . . . . . .
Setting the DVD player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
118
119
119
120
Setting the audio language . . . . . . . . . . . . . . . . . . . . . . . . . .
Inputting a code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting subtitle language . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inputting a code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting menu language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inputting a code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting display of multi-angle mark
(angle selection mark) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting viewer restriction . . . . . . . . . . . . . . . . . . . . . . . . . . .
121
121
122
122
123
123
124
125
15
Changing video output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Switching dual play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Table of language codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
How to operate the video CD player
(Asia only)
How to use the video CD player . . . . . . . . . . . . . . . . . . . . 129
Watching a video CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Watching a video CD using the touch switch . . . . . . .
Watching a video CD using the panel buttons . . . . . .
Watching a video CD using the remote control . . . . .
Using the menu screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
129
130
130
130
Displaying menu screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Selecting menu list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Advancing to the next scene or returning to the beginning of
the scene being played . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Using panel buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Using remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Fast-forwarding/rewinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Using panel buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Using remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Specifying a track to playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Pausing/Advancing the video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Stopping playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Using slow motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Turning off the video CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Turning off the video CD using the panel buttons . . . 133
Turning off the video CD using the remote control . . 133
How to operate the Area Shot function
(U.S.A./CANADA only)
Before using the Area Shot . . . . . . . . . . . . . . . . . . . . . . . . 134
About the Area Shot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
To use the Area Shot function . . . . . . . . . . . . . . . . . . . . . . . 135
Map data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
GPS (Global Positioning System) . . . . . . . . . . . . . . . . . . . . 136
16
How to use the Area Shot function . . . . . . . . . . . . . . . . . . 137
Displaying ePID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Reading Area Shot data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Changing Area Shot screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
How to view the Area Shot screen . . . . . . . . . . . . . . . . . . . . . . . . . 141
Displaying touch switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Switching the map reduction scale . . . . . . . . . . . . . . . . . . . . . . . . 143
Displaying the all-route map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Switching guidance points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Switching text information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Re-scrolling through text information . . . . . . . . . . . . . . . . . . . . . . 145
Displaying POI vicinity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Selecting POI category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Displaying POI vicinity information . . . . . . . . . . . . . . . . . . . 147
When an optional GPS unit is connected . . . . . . . . . . . . . . . . . . . 148
To end Area Shot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
ESN security operating procedure
ESN security operating procedure . . . . . . . . . . . . . . . . . . 149
About ESN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
How to switch the security type
(Key CD security/"Memory Stick" security). . . . . . . . . . . . . . . . . . 150
How to operate the ESN (Key CD) security . . . . . . . . . . . . . . . . . . 151
How to program the Key CD . . . . . . . . . . . . . . . . . . . . . . . . .
How to cancel the Key CD. . . . . . . . . . . . . . . . . . . . . . . . . . .
How to change the Key CD . . . . . . . . . . . . . . . . . . . . . . . . . .
How to resume normal operation
(ESN security lock out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What happens if an incorrect CD is inserted? . . . . . . . . . .
How to operate the ESN (“Memory Stick”) security . . . . . . . . . . .
How to record a security code . . . . . . . . . . . . . . . . . . . . . . .
How to cancel the “Memory Stick” security . . . . . . . . . . . .
Canceling the security function by entering the
security code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Canceling the security function using a
“Memory Stick Duo” . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to change the “Memory Stick Duo” . . . . . . . . . . . . . . .
How to resume normal operation
(ESN security lock out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
151
152
153
153
154
155
155
157
157
158
159
159
17
Canceling ESN security lock out using security
code entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Canceling ESN security lock using
“Memory Stick Duo” . . . . . . . . . . . . . . . . . . . . . . . . . . .
What happens if a “Memory Stick Duo” or security code
is incorrect? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to operate the ACC security . . . . . . . . . . . . . . . . . . . . . . . . . .
159
160
162
163
How to turn the security indicator on/off. . . . . . . . . . . . . . . . . . . . 164
How to read the Electronic Serial Number . . . . . . . . . . . . . . . . . . 164
How to use the remote control
Before using remote control . . . . . . . . . . . . . . . . . . . . . . . 165
How to use the remote control . . . . . . . . . . . . . . . . . . . . . 166
Turning the power on/off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Adjusting the audio volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Muting the volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Switching playback modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
How to select the tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Selecting the FM/AM band . . . . . . . . . . . . . . . . . . . . . . . . . . 167
How to play back CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Switching disc modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Replacing the battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
How to operate the optional 5.1ch
decoder & AV selector unit
Sound quality information . . . . . . . . . . . . . . . . . . . . . . . . . 170
Functions of the optional 5.1 ch decoder & AV selector
unit is connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
About parametric EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About time alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About E-iSERV sound effect customizations . . . . . . . . . . .
About automatic parametic equalizer . . . . . . . . . . . . .
171
173
174
175
175
Adjusting sound quality . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Displaying the sound adjustment screen . . . . . . . . . . . . . . . . . . . 176
Adjusting PEQ (Parametric equalizer) . . . . . . . . . . . . . . . . . . . . . . 178
18
Adjusting/Saving a PEQ . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a PEQ pattern from memory . . . . . . . . . . . . . . . .
Measuring/Displaying frequency characteristics . . . . . . . .
To avoid writing measurement results to the
“Memory Stick Duo” . . . . . . . . . . . . . . . . . . . . . . . . . . .
To write measurement results to a
“Memory Stick Duo” . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting POS (Positioning selector) . . . . . . . . . . . . . . . . . . . . . .
179
181
181
181
182
183
Setting the balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Setting LOUDNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Setting the harmonizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Setting/Adjusting surround system . . . . . . . . . . . . . . . . . . . . . . . . 186
Setting the Dolby Pro Logic II. . . . . . . . . . . . . . . . . . . . . . . .
Setting the Center Level . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Rear Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Center Width . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Compression . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting/Adjusting speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
186
187
187
187
188
189
Adjusting time alignment . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic adjustment . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting X-Over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting sub-woofer output level. . . . . . . . . . . . . . . . . . . .
Setting phase control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting speaker level. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting speaker size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Importing sound data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
189
189
191
191
193
194
195
196
198
Setting display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Screen settings of the optional 5.1 ch decoder & AV
selector unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
External monitor image settings . . . . . . . . . . . . . . . . . . . . . . . . . . 201
How to operate the optional HD radio
tuner (U.S.A. only)
How to use the HD radio . . . . . . . . . . . . . . . . . . . . . . . . . . 202
About HD Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Listening to the HD radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Listening to the HD radio using the
touch switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
19
Listening to the HD radio using the
panel buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Switching the band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Selecting radio stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Manual selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selection when using preset switches . . . . . . . . . . . . . . . .
Saving radio stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
203
203
203
204
Saving manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving with ASM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing stations saved by ASM . . . . . . . . . . . . . . . . . . . .
Checking preset stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
204
204
204
205
HD radio information screen display . . . . . . . . . . . . . . . . . . . . . . . 206
HD radio reception settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Turning off the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
How to operate the optional SIRIUS
satellite radio tuner (U.S.A. only)
How to use the SIRIUS satellite radio . . . . . . . . . . . . . . . . 208
About SIRIUS satellite radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Listening to the SIRIUS satellite radio . . . . . . . . . . . . . . . . . . . . . . 209
Listening to SIRIUS satellite radio using the touch
switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Listening to SIRIUS satellite radio using the panel
buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Selecting SIRIUS channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Manual selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selection using preset switches . . . . . . . . . . . . . . . . . . . . .
Category selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
210
210
210
211
Direct Channel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Saving SIRIUS channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
SIRIUS satellite radio information screen display . . . . . . . . . . . . 213
Turning off the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
20
How to operate the optional TV tuner
(U.S.A./CANADA/KOREA/TAIWAN only)
How to use the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Watching TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Watching TV using the touch switches . . . . . . . . . . . . 214
Watching TV using the panel buttons. . . . . . . . . . . . . . 214
Selecting channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Manual selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Automatic selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Selection when using preset switches . . . . . . . . . . . . . . . . 215
Saving channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Saving manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving with AUTO.P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing stations saved by AUTO.P. . . . . . . . . . . . . . . . . .
Checking preset stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
216
216
216
218
Switching to TV/VTR mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
To end TV mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
How to operate the VTR
How to use the VTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Viewing the VTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Viewing the VTR using the touch switches . . . . . . . . . 219
Viewing the VTR using the panel switches . . . . . . . . . 219
Switching to the TV/VTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Turning off the VTR mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
How to operate the Back-eye Camera
Back-eye Camera operations. . . . . . . . . . . . . . . . . . . . . . . 222
Back-eye Camera image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Automatic back-eye camera image display setting . . . . . . . . . . . 224
21
For reference
Important Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
If one of these messages appears . . . . . . . . . . . . . . . . . . . . . . . . . 226
Before asking for repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Products equipped with Dolby Digital . . . . . . . . . . . . . . . . . . . . . . 230
Products equipped with Macrovision . . . . . . . . . . . . . . . . . . . . . . 230
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
About care and maintenance. . . . . . . . . . . . . . . . . . . . . . . 233
About care and maintenance - main unit. . . . . . . . . . . . . . . . . . . . 233
Topic index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
About screen and sound adjustment. . . . . . . . . . . . . . . . . . . . . . . 234
About using AM/FM radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
About using the CD player and CD changer . . . . . . . . . . . . . . . . . 235
About using the MP3/WMA player . . . . . . . . . . . . . . . . . . . . . . . . . 236
About using the DVD player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
About video CD player (Asia only) . . . . . . . . . . . . . . . . . . . . . . . . . 238
About Area Shot (U.S.A./CANADA only) . . . . . . . . . . . . . . . . . . . . 238
About ESN security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
About optional 5.1ch decoder & AV selector unit. . . . . . . . . . . . . 239
About optional HD radio (U.S.A. only) . . . . . . . . . . . . . . . . . . . . . . 240
About optional SIRIUS satellite radio (U.S.A. only) . . . . . . . . . . . 240
About optional TV (U.S.A./CANADA/KOREA/TAIWAN only) . . . . 241
About optional Back-eye Camera. . . . . . . . . . . . . . . . . . . . . . . . . . 241
When something isn't clear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Common component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
243
243
243
243
244
How to contact customer service . . . . . . . . . . . . . . . . . . . 245
22
Before installation
Before installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Installation preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Mounting instruction
Mounting instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Mounting the main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Names and function of terminals . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Connecting the parking-brake signal and the reverse signal . . . 254
System connection example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
The Topic Index simplifies searches for explanations about
individual features. When confused by an operation, use the Topic
Index to search for information about the operation.
23
Introduction
How to use this manual
Item title
Section title
A title is
assigned to
each item.
A title is assigned to each section.
Operation title
A title is assigned
to each operation.
Detailed operation
title
A title is assigned to
each detailed
operation.
Operation
procedure
Describes the
operation.
Proceed with the
operation according
to the numerical
order.
Attention
Additional points
regarding operation
are given here.
24
I
II
III
IV
V
Section side
heading
VI
The side heading for
the current section.
VII
VIII
Operation screen
A screen showing
the operation.
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
25
Introduction
Features
DVD player with sharp video and dynamic sound
(Page 106)
Plays DVD videos recorded with high image
and sound quality.
(DVD media is able to record a movie with high
quality video and digital sound that exceeds
the quality of CD media.)
MP3 player that plays back the equivalent of several albums
of music recorded on a single music disc (Page 92)
MP3 audio compression technology
compresses audio data to one-tenth the
original size. CD-R/RW with recorded MP3s
can be played.
Selection and display of favorite wallpaper (screen
backgrounds) (Page 66)
Wallpaper of your choice can be switched and
displayed for use as the background of the
information screen and audio operation
screens.
The screen from a navigation unit can also be
linked and selected.
26
Area Shot for displaying map (U.S.A./CANADA only) (Page 134)
Using Area Shot, maps to destinations and
guidance information can be displayed on
your unit if you have set route using EiSERV (web site).
I
II
III
IV
System upgrade
● CD changer (Page 103)
A CD changer enables non-stop playing of
multiple discs, for long drive convenience.
Playing and selecting songs among the
discs can be done with ease.
V
VI
VII
VIII
IX
X
● VTR (Page 219)
Videos can be watched if a VTR deck is
connected.
XI
XII
XIII
XIV
● HD Radio tuner (Page 202)
Terrestrial digital broadcasts can be received
if the optional HD Radio tuner unit is
connected.
XV
XVI
XVII
XVIII
XIX
27
Introduction
Features
● SIRIUS satellite radio tuner (Page 208)
Satellite radio broadcast can be received if
the optional SIRIUS satellite radio tuner unit
is connected.
● 5.1ch decoder & AV selector unit (Page
170)
Fine audio adjustments can be performed by
connecting an optional 5.1ch decoder & AV
selector unit.
28
Introduction
Before using the deck
●Be very careful and pay close attention to safety when
operating the audio controls while driving and set the
volume level so that you can still adequately hear sounds
outside the vehicle.
Otherwise accidents may occur.
I
II
III
IV
●Never continue to use the system if it is malfunctioning in
any way. If smoke, abnormal noises or abnormal odors
are noticed, turn off the power immediately.
V
VI
VII
●Exercise caution when experiencing not weather or high
temperature. The temperature inside the vehicle can
increase during hot weather. Wait for the temperature
inside the vehicle to drop before using the unit.
Otherwise damage to equipment may occur.
VIII
IX
X
XI
XII
●Drivers should not operate the DVD while driving. The
volume level should be set to so that you can still
adequately hear sounds outside the vehicle.
Otherwise damage may occur.
XIII
XIV
XV
XVI
●Do not disassemble or modify the deck.
This equipment is designed with a very precise structure.
Contact the store of purchase in the event of any unsatisfactory performance.
XVII
XVIII
XIX
29
Introduction
Before using the deck
●Do not apply excessive force to the monitor, or damage to
the equipment may occur.
●Do not insert any objects other than discs or “Memory
Stick Duos” into their respected slots.
Otherwise damage may occur.
●Be careful not to get fingers or other objects caught in the
monitor when it is being extended or retracted into place.
Interference can cause an injury or damage the equipment.
●When removing a disc or “Memory Stick Duo” from the
deck, do so in a horizontal direction.
Do not forcibly pull up or press down when removing
them.
Improper removal can scratch the disc, cause deck noise
or damage the “Memory Stick Duo”.
30
About discs
●Water droplets (condensation) can form on the inside of the unit during cold or
rainy weather in the same way car windows can fog up. If this occurs, there may
be a drop in the performance of the equipment. To help reduce this performance
variation, ventilate or dehumidify the vehicle for a short time prior operating the
equipment.
●To safeguard the components of the equipment, this equipment will automatically
stop the player if a malfunction is detected. If the player does not resume normal
operation, it is possible that the unit has been damaged. Contact the store of
purchase.
●It is possible that the sound may seem to skip or cuts out if the vehicle
experiences violent motion on rough roads.
About supported disc types
●An audio or DVD video disc bearing one of the marks shown below can be
played. Only DVD-R/RW (DVD-Recordable/ReWritable) and DVD+R/RW
(DVD+Recordable/ReWritable) discs recorded in Video mode can be played.
Discs recorded in Video mode (VR) cannot be played.
●Depending on the type of disc used, playback may not be possible.
I
II
III
IV
V
VI
VII
VIII
IX
X
●Supports Dolby Digital. Discs bearing the following mark can be used.
XI
XII
Manufactured under license from Dolby Laboratories, Inc. Dolby and the double-D symbol are
registered trademarks of Dolby Laboratories.
●It is possible that a CD-R (CD-Recordable) or CD-RW (CD-ReWritable) disc will
not play on the unit due to special disc characteristics, scratches, dirt or
deterioration caused by long storage in the vehicle. In addition, an unfinalized
CD-R or CD-RW disc written in CD-R, CD-RW or UDF format will not play in this
equipment.
●It is possible that a DVD-R/RW (DVD-Recordable/ReWritable) or DVD+R/RW
(DVD+Recordable/ReWritable) disc will not play on the unit due to special disc
characteristics, scratches, or dirt or deterioration caused by long storage in the
vehicle. In addition, an unfinalized DVD-R or DVD-RW disc will not play in this
equipment. It is possible that discs recorded using a computer may not play in
this equipment depending on the environment and/or settings of applications.
●The CD-TEXT function requires commercially available CDs which support
CD-TEXT. It is possible that characters in CD-R and CD-RW data may not be
displayed correctly.
XIII
XIV
XV
XVI
XVII
XVIII
XIX
31
Introduction
Before using the deck
●Do not use discs with transparent or semi-transparent portions within the
recording area, or see through discs, since they cause the equipment to operate
improperly.
●Super Audio CDs cannot be played.
●CCCDs (Copy Control CD) do not conform to official CD
standards and are not supported.
●CD-EXTRA discs can be played as audio CDs.
●Voice tracks on Mixed Mode CDs cannot be played. Only
music tracks will be played.
●Video-CDs can be played. (Asia only)
About handling discs
●Be sure to store discs in their cases and keep them out of
direct sunlight. Discs can warp and become unusable.
●Do not apply paper-based tape to either the recording
side or label side of a disc. Otherwise damage to the disc
or equipment may occur.
●Do not use discs where cracks and/or large warps in the
disc are present. Otherwise damage to the disc or
equipment may occur.
●Do not touch the recorded side of a disc when handling it.
(Iridescent side of the CD) The disc may become dirty
causing skipping type effect to occur.
●Using a disc that has become dirty can scratch the disc
and result in sound having a skipping type effect. Use a
commercially available compact disc cleaner to clean the
CD, wiping lightly from the center to the edge.
32
About new discs
Rough Edges
Ballpoint pen
●You may notice that some brand new discs are rough
around the center hole or outside edge. Remove the
rough edges with the side of a ballpoint pen, etc. Rough
edges may prevent proper loading in the unit. Flakes from
the rough edges may also stick to the recorded surface,
interfere with playback, and/or damage the disc or
equipment.
I
II
III
IV
About rental discs
Flakes
Recorded surface
●Do not use CD discs with attached cellophane tape, rental
CD discs with glue protruding from labels or discs with the
residue of peeled adhesives. Using discs with those
conditions can prevent the player from proper operation
and cause damege to the disc or equipment.
About specially shaped discs
●Specially-shaped CDs cannot be played. Do not attempt
to play them, even with an adapter, since they may
damage the player.
●Please do not use a commercially available lens cleaner,
because it may cause damage to the pickup of the player.
About disc accessories
CD stabilizer ring
V
VI
VII
VIII
IX
X
XI
XII
XIII
●Do not use accessories (stabilizers, protective seals, laser
lens cleaners, etc.) sold for “improving sound
performance” or “protecting CDs.” The changes in CD
thickness or outside dimensions made by these
accessories may cause problems in the player.
XIV
●Do NOT attach any ring-shape protector (or other
accessory) to your discs. Those protectors are
commercially available and said to protect discs and to
improve sound quality (and anti vibration effect), but they
can do more harm than good during regular use. The
most common problems are insert/eject related problems
and “No playback” problems due to the protector ring
coming off in the disc mechanism.
XVII
XV
XVI
XVIII
XIX
33
Introduction
Before using the deck
About the “Memory Stick Duo”
●Do not leave the “Memory Stick Duo” in places exposed to static electricity or
electrical noise. Otherwise, data may be lost.
●To safeguard the components of the player, this equipment will automatically
stop the player if a malfunction is detected. If the player does not resume normal
operation, it is possible that the unit has been damaged. Contact the store of
purchase.
●After uploading of data to the hard drive is complete, promptly remove the “Memory
Stick Duo”.
●Do not remove the “Memory Stick Duo” while it is being used to upload data to the
this unit. Otherwise, data may be lost. Please be aware that Eclipse will not be held
responsible for lost data.
About supported “Memory Stick Duo” types
●“Memory Stick Duos” with a capacity of up to 128MB are supported.
●“Memory Stick Duo” PRO is not supported.
●“Memory Stick Duos” labeled with the following marks can only be used when
registering a pass code in database update or Eclipse Security Network (ESN).
“Memory Stick Duo”
are registered trademarks of Sony Corporation.
●The “Memory Stick Duo” cannot be used on this equipment if it has been
formatted using a device other than the dedicated device.
34
About handling the “Memory Stick Duo”
●Regularly wipe clean
any dust or dirt from the
surface of the cartridge
with a dry cloth.
●Do not use “Memory Stick
Duos” with tape or peeling
labels.
●Store in a dry place, out
of direct sunlight.
Otherwise, it may
become impossible to
use the “Memory Stick
Duo”.
I
II
III
IV
V
●Always place in the
case provided when
transporting or storing.
●Do not touch terminals
with metal objects or
your bare hands.
VI
VII
VIII
IX
About the LCD panel
●The LCD panel can appear to be white or black when seen from certain angles.
●The screen will be difficult to read when external light source (bright lights,
sunlight) falls sunlight falls on the display.
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
35
Introduction
Before using the deck
About TV (U.S.A./CANADA/KOREA/TAIWAN only)
●When the loss of power is lost due to vehicle battery replacement, replacing
fuses, etc., all preset channels will be erased.
●It may be difficult for the TV to maintain optimal reception due to variation in
signal strength or interference from other objects. The main causes of
interference are listed below.
• Visual or audio static may result when in
close proximity to overhead train wires,
high-tension wires, traffic signals, neon
signs, etc.
• Depending on the signal, buildings and
mountains may adversely affect reception.
• Visual or audio static may result when in
close proximity to radio broadcasting or
ham radio antennas.
• Signal reception will become extremely
weak when driving through a tunnel.
• Signal reception will become weak when
traveling at a great distance from the
broadcasting station.
• In some areas, visual or audio static may
result when in close proximity to TV or radio
towers. This is due to the influence of
electro-magnetic waves outside of the
reception range.
36
Introduction
Name of controls and parts
The unit can be operated by pressing buttons on the detachable panel (panel buttons) and by
touching buttons displayed on the screen (touch switches).
I
Panel buttons
With display retracted
Control panel detached
II
III
IV
V
VI
VII
With display opened
VIII
IX
X
XI
XII
VOL button
PWR button
SOURCE button
button
Security indicator
EJECT button
OPEN·TILT button
button
Detach panel release
button
DISC slot
“Memory Stick Duo” slot
FUNC button
SOUND button
MENU button
Area Shot button
Turn to adjust volume.
Press to turn deck power ON/OFF
Press to switch source modes.
Press to select radio stations, CD audio tracks and DVD chapters.
Flashes when the ESN security system is in operation.
Press to eject DISC.
Press to open the display panel.
Press to select radio stations, CD audio tracks and DVD chapters.
Press to detach the control panel.
Disc insertion and removal slot
Inserts and ejects “Memory Stick Duo”.
Press to switch to function mode and display adjustment mode.
Press to switch to sound adjustment mode.
Press to display the audio menu screen that enables the switching of
audio modes.
Press to switch to Area Shot screen.
XIII
XIV
XV
XVI
XVII
XVIII
XIX
37
Introduction
Name of controls and parts
Touch switches
Unit can be operated by touching switches on the screen.
[About the operation of touch switch]
● Touch the switches until you hear a beep.
● Touch the switches lightly to prevent damage to the screen.
● If a switch does not respond, remove your finger and touch it again.
● Unavailable switches are shaded.
● When a function for a switch is active, the color of that switch will change.
Touch these switches with your fingers.
Using a pen, pencil or object with a hard or sharp tip to touch the screen may
cause damage to the unit.
38
Remote control
I
II
III
IV
V
VI
PWR button
Press to turn unit power ON/OFF.
MODE button
Press to switch SOURCE modes.
BAND button
Press to switch radio band.
MUTE button
Press to mute audio and cancels mute.
VOL button
Turn to adjust volume.
MENU button
Press to display DVD menu and title menu.
NUMBER button
Press to search for video track.
CLEAR button
Press to clear numbers currently being input.
SEARCH button
Press to switch between search for DVD chapters and DVD title.
SET UP button
Press to display DVD operation screen.
ANGLE button
Press to switch angle of the DVD.
AUDIO button
Press to switch voices during DVD playback.
SUB TITLE button
Press to switch during DVD playback.
ENTER button
Press to set the content for each setting.
RETURN button
Press to return to previous screen.
(cursor) button
Press to move the cursor during operation of DVD menu.
STOP button
Press to stop video playback.
PLAY button
Press to start (restart) video playback.
SLOW button
Press to activates slow-motion video playback.
PAUSE button
Press to pauses video playback.
< DISC > button
Press to select disc in CD changer or select radio preset channels.
CHAPTER button Press to select DVD chapter and disc track.
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
39
Basic operation
How to turn the power ON or OFF
Turning the power on and off
When the power is turned on, the last state or mode used prior to power turning off will be
restored.
When power is OFF, press the
.
● The power will come ON.
When power is ON, press the
.
● The power will go OFF.
The display can be set to automatically open and close when the power is
switched ON or OFF. (See “Setting the display AUTO CLOSE function” on
page 45)
40
Basic operation
Display open/tilt/close
Opening the display
Turn the ignition switch ON.
ON
I
II
Press OPEN·TILT .
III
● Opens the display.
OPEN·TILT
button
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
Do not force the display to open manually.
Applying excessive force to the display could damage it.
XVIII
XIX
The display can be set to automatically open when the ignition switch is turned ON.
(See “Setting the display AUTO CLOSE function” on page 45)
41
Basic operation
Display open/tilt/close
Adjusting the angle of the display
With the display open, press
OPEN·TILT for less than 1
second.
● The display setting screen will appear.
OPEN·TILT
button
Touch TILT .
● The display will tilt upwards by one
step (5°). Each touch of switch tilts the
panel by another step.
● The display can be adjusted to 7
different tilt positions. (Front Position)
(Rear Position: 5 tilt positions)
After completing the adjustment,
press OPEN·TILT .
OPEN·TILT
button
Do not attempt to manually adjust the display.
Applying excessive force to the display could damage it.
The adjusted display angle will be saved. When reopened, the display will
automatically return to this angle.
42
Switching the display’s pull-out positions
With the display open, press
OPEN·TILT for less than 1
second.
● The display setting screen will appear.
I
OPEN·TILT
button
Touch POSITION .
II
III
IV
● Each time the switch is touched, the
display pull out positions will be
changed in the following order shown
below.
V
VI
Rear position (toward the dashboad)
VII
*Front position (toward the viewer)
*: The front position cannot be adjusted
when the screen is in the 6th or 7th
tilt position.
VIII
IX
X
XI
XII
XIII
XIV
When adjustment is complete,
press OPEN·TILT .
XV
OPEN·TILT
button
XVI
XVII
Do not attempt to manually adjust the pull-out display. Applying excessive force to
the display could damage it.
XVIII
XIX
The pull-out position of the display will be saved once it has been adjusted. The
display will then automatically return to this position when it is reopened.
43
Basic operation
Display open/tilt/close
Closing the display
With the display open, press
OPEN·TILT for less than 1
second.
OPEN·TILT
button
Touch CLOSE .
●Do not attempt to close the display manually. Applying excessive force to the
display could damage it.
●When closing the display, check to make sure it has retracted completely. The
display could be damaged if left in a partially closed position.
●The display can be closed by pressing the OPEN·TILT button until a beep
noise is heard (after approx. 1 second).
● If the ignition switch is turned OFF while the display is open, the display can still
be closed if the OPEN·TILT button is pressed before a beep noise is heard
(within approx. 1 second).
44
Setting the display AUTO CLOSE function
The display can be set to automatically open when the ignition switch is turned ON, and
automatically close when it is turned OFF.
With the display open, press
OPEN·TILT for less than 1
second.
I
II
OPEN·TILT
button
Touch AUTO CLOSE .
III
IV
V
● Touching the switch toggles between
ON and OFF.
VI
VII
VIII
IX
When adjustment is complete,
press OPEN·TILT
X
OPEN·TILT
button
XI
XII
XIII
XIV
XV
XVI
Do not enable the AUTO CLOSE function if the display interferes with the shift
lever position (P range) when it is opening and/or closing.
If the display is closed before the ignition switch is turned OFF, the display will not
automatically open when the ignition switch is turned ON again. Press
OPEN·TILT to open the display.
XVII
XVIII
XIX
45
Basic operation
Inserting/Ejecting the disc or “Memory Stick Duo”
How to insert disc (CD/DVD) and “Memory Stick Duo”
When you want to listen to music, insert a CD into the disc slot. When playing a DVD video,
insert a DVD video disc into the disc slot. When reading data (ESN recorded data and sound
quality data etc.), insert the “Memory Stick Duo” into the “Memory Stick” slot.
Inserting disc (CD/DVD) or “Memory Stick Duo”
■When inserting a DVD or CD
Insert a DVD or CD by holding it
label up with one finger on the
center rim and another finger on
the edge.
● CD or MP3 playback starts as soon as
a CD is inserted.
● Playback starts as soon as a DVD is
inserted.
■When inserting a “Memory Stick
Duo”
Press the detach panel release button and remove the control panel.
Insert the “Memory Stick Duo” in the direction on the
heard.
mark until a click is
● Once the “Memory Stick Duo” meets the back stopper, do not continue to apply force.
(Once fully inserted, the “Memory Stick Duo” should still protrude a few millimeters.)
46
Install the control panel.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
●DVDs and CDs are inserted into the same slot. Only one type of disc can be
inserted at any time.
●Do not remove the “Memory Stick Duo” while reading data. Otherwise, data may
be lost. Please be aware that Eclipse will not be hold responsible for lost data.
XIX
47
Basic operation
Inserting/Ejecting the disc or “Memory Stick Duo”
How to eject disc (CD/DVD) or “Memory Stick Duo”
■When ejecting a DVD or CD
Press
.
● The disc is automatically ejected.
● If the disc does not eject (is not
released from the internal mechanism),
press and hold
for at least five
seconds.
■When ejecting a “Memory Stick Duo”
Press the detach panel release
button and remove the control
panel.
Lightly press the “Memory Stick
Duo” (once) to eject.
Install the control panel.
48
EJECT
button
Basic operation
Switching source
The unit can be used when the vehicle's ignition switch is on or in the ACC position.
● This unit supports the use of a remote control. A DVD remote control is included. See page
165 for instructions on operation of the remote control.
I
Switching the source
II
Switching source using panel buttons
III
Press SOURCE .
IV
● Each time the button is pressed, the
source will be changed in the order
shown below.
V
FM
VTR
AM
TV
SIRIUS
CDCH
DISC (DVD/
CD/MP3·WMA)
● Sources which are not connected to
the unit will be skipped.
VI
SOURCE
button
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
49
Basic operation
Switching source
Switching source using touch switches
Press MENU .
● The SOURCE MENU screen will
appear.
When the SOURCE MENU switch
is touched, the operation screen for
the available sources is displayed.
50
MENU
button
Basic operation
Operational screen for each source
The operation screen for each source will appear as shown below.
● AM radio operation screen
● FM radio operation screen
I
II
III
● CD player operation screen
● MP3/WMA player operation screen
IV
V
VI
VII
● DVD player operation screen
● CD changer operation screen (optional)
VIII
IX
X
XI
● HD radio operation screen (optional: U.S.A. only)
● SIRIUS satellite radio operation screen (optional: U.S.A. only)
XII
XIII
XIV
XV
● TV operation screen (optional: U.S.A./CANADA/KOREA/TAIWAN only)
● VTR operation screen (optional)
XVI
XVII
XVIII
XIX
When the operation screen for the DVD, TV or VTR has not been operated for 6 seconds or
more, it will automatically be canceled.
51
Basic operation
Adjusting the volume
Adjusting the main volume
Adjusting main volume using touch switches
Touch
●
or
.
: Volume UP (louder)
: Volume DOWN (quieter)
Adjusting main volume using panel buttons
Turn the VOL button.
● Adjustment levels from 0 to 80 are
available.
Turn to the right :Volume UP (louder)
Turn to the left : Volume DOWN
(quieter)
● Press the VOL button to cut or mute
the volume or restore it instantly. Press
the VOL button again or turn it to the
right to turn the sound ON.
52
VOL button
Basic operation
Adjusting sound quality
By adjusting the equalizer and the volume balance you can simulate a custom sound
environment within the vehicle.
Displaying the sound adjustment screen
I
Press SOUND .
II
● The sound adjustment screen will
appear.
III
● Touch any of the following buttons on
the sound adjustment screen to display
the corresponding adjustment screen.
IV
V
VI
● Sound adjustment screen
● Parametric equalizer adjustment screen
VII
VIII
PEQ
IX
X
● Position setting screen
XI
XII
POS
XIII
XIV
● Time alignment adjustment screen
SETTING
XV
XVI
XVII
XVIII
XIX
53
Basic operation
Adjusting sound quality
The following settings/adjustments can be made in the operation screens and setting
screens.
Touch switch/item
PEQ
Page
56
Circle Surround II
Circle surround can easily be simulated using the existing
speaker system in your vehicle (when the vehicle has 4
speakers).
55
TruBass
Deep bass sounds can be heard even if a subwoofer is not
connected.
55
Sound localization can be adjusted according to the
number and position of passengers in order to obtain
optimum acoustic effects.
58
The left/right/front/rear balance can be adjusted.
59
LOUDNESS
To emphasize bass/treble when listening at low volume.
60
HARMONIZER
To set the harmonizer level so that compressed data is
played back with a sound quality corrected to a level as
close as possible to that of the original data.
60
Time Aligment
This function corrects the positional characteristics and
frequency characteristics in order to delay the signals
being output from the various speakers so that the signals
from each speaker reach the listening position at the same
time.
61
The sub woofer output can be adjusted.
63
POS
FADER BALANCE
Woofer
54
Function
The parametric equalizer adjusts 7 frequency bands.
Setting Circle Surround II
The Circle Surround II function enables surround sound and boosts bass even if the center
speaker and sub woofer are not connected. It can also be applied to dialog data when
listening to the radio.
Touch CS II in the sound
adjustment screen.
● Each time the switch is touched, the
CS II setting will be changed in the
following order shown below.
OFF
High
Low
I
II
III
IV
V
VI
● High : High re-creation effect
Low : Low re-creation effect
OFF : The function is disabled.
Setting CS II TruBass
CS II TruBass allows for deep bass sounds without the aid of a subwoofer.
VII
VIII
IX
X
Touch TruBass in the sound
adjustment screen.
XI
● Touching the switch toggles between
ON and OFF.
XII
● When CS II is High or Low, TruBass
can be turned ON/OFF.
XIII
XIV
XV
XVI
XVII
XVIII
●You cannot set Circle Surround II at the same time as POS, or LOUDNESS.
●Circle Surround II, CS II TruBass, SRS, and the (●) symbol are trademarks of
SRS Labs, Inc.
●Circle Surround II technology is manufactured under license from SRS Labs, Inc.
XIX
55
Basic operation
Adjusting sound quality
Adjusting PEQ (parametric equalizer)
The parametric equalizer adjusts 7 frequency bands.
Adjusting/Saving a PEQ
Touch the PEQ in the sound
adjustment screen.
Touch the BAND to select the
band to be adjusted.
● Each time the switch is touched, the
band will be changed in the following
order shown below.
Band1
Band7
Band2
Band6
Band3
Band5
Band4
Touch
or
to select the
frequency to be adjusted.
●
: Increase frequency.
: Decrease frequency.
● Each band can be set to the following
frequencies:
Band
1
2
3
4
5
6
7
Frequency (Hz)
63, 80, 100
125, 160, 200
250, 315, 400, 500
630, 800, 1k, 1.25k
1.6k, 2k, 2.5k, 3.15k
4k, 5k, 6.3k, 8k
10k, 12.5k, 16k
Touch
or
frequency level.
●
56
to adjust the
: Increase level
: Decrease level
Touch the Q to select the Q
curve pattern.
● Each time the switch is touched, the Q
curve pattern will be changed in the
following order shown below.
NORMAL
SLOW
SHARP
I
II
III
IV
Repeat the operations in step
to
to change the setting for each
channel and band.
● The frequencies that have been
adjusted for either the channel or band
cannot be selected.
Touch the switch you want to use
to save ( 1 to 5 ) until you hear
a beep.
● The saved PEQ setting can be
selected for further customization.
● Touch BACK after making changes.
The PEQ mode adjustments will be
saved and system will return to the
previous operation screen.
Selecting a PEQ pattern from memory
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
Touch the 1 to 5 .
XV
● The preset pattern stored in memory
will be retrieved.
XVI
● Touch BACK after making changes.
The PEQ mode adjustments will be
saved and system will return to the
previous operation screen.
XVII
XVIII
XIX
57
Basic operation
Adjusting sound quality
Adjusting POS (Positioning selector)
Sound localization can be adjusted according to the number and position of passengers in
order to obtain optimum acoustic effects.
A seat's sound localization can be adjusted simply by touching the switch.
Touch POS in the sound
adjustment screen.
Touch each seat image displayed
in the POSITION setting screen to
switch the sound localization for
that seat.
● The selected position will appear in a
green frame. Touch the seat again to
cancel the selection. The four positions
shown by the table below can be set.
● Touch OFF to cancel all settings.
● Touch BACK after making changes.
The position will be saved and the
system will return to the previous
operation screen.
Touch switch
Function
Touch switch
Function
Acoustics optimized for
driver's seat
Acoustics optimized for
both front seats
Acoustics optimized for
passenger's seat
Acoustics optimized for
rear seats
If the positioning selector has been set (to a setting other OFF), the FAD/BAL
(Fader/Balance) settings cancelled (next page).
58
Setting the balance
The left/right/front/rear balance can be adjusted so that sound from all speakers arrives at the
listener's ears at the same time.
Touch FAD/BAL in the POSITION
setting screen to display the
volume balance adjustment
screen.
I
II
III
IV
V
Touch
,
,
or
.
● The adjustment level can be set to one
of 15 levels between F (front) and R
(rear).
● The adjustment level can be set to one
of 15 levels between L (left) and R
(right).
● Touch CENTER to set the volume
balance to the center position.
● Touch BACK after making changes.
The set volume balance will be saved
and the system will return to the
previous operation screen.
● To set the position again, touch POS
and repeat the steps above.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
●If the balance has been set (to a setting other CENTER), the positioning selector
setting will be cancelled (previous page).
,
,
or
while making fine adjustments to adjust
●Touch and hold
values continuously. Adjustment will lock when it reaches the center value, and
,
,
or
must be touched again to continue adjustment.
XVIII
XIX
59
Basic operation
Adjusting sound quality
Setting LOUDNESS
Audio can be modulated to correct for insufficient bass and treble when listening at low
volume.
Touch LOUDNESS in the sound
adjustment screen.
● Touching the switch toggles between
ON and OFF.
Setting the harmonizer
It is possible to set the sound quality boost level to automatically regenerate harmonics such
as reverberation, depth, and tone lost in compression, producing a much clearer sound.
Touch Harmonizer in the sound
adjustment screen.
● Each time the switch is touched, the
Harmonizer settings will be changed in
the following order shown below.
OFF
Hi
Low
● LOW : Low level of correction
HI : High level of correction
OFF : No correction
You cannot set LOUDNESS while using Circle Surround II.
60
Simplified time alignment settings (Time Alignment)
This function corrects the position characteristics and frequency characteristics in order to
delay the signals being output from the various speakers so that the signals from each
speaker reach the listening position at the same time.
Touch SETTING .
● The Time Alignment screen will
appear.
I
II
III
IV
V
VI
Selecting the type of vehicle (Car Type)
You can select the time alignment settings to match your vehicle from a range of preset
settings for different types of vehicles, allowing you to select the optimum time alignment
settings automatically.
Touch Car Type .
● Each time a car selection is touched,
the Car Type will be changed in the
following order shown below.
Compact Sedan Wagon
Truck SUV Mini Van
● Touch BACK after making changes.
The time alignment settings will be
saved and system will return to the
previous operation screen.
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
●Time Alignment cannot be operated when the CSII is ON.
●Before selecting a position, make sure that CSII is OFF. (For details about
turning CSII ON/OFF, see page 55.)
XIX
61
Basic operation
Adjusting sound quality
Tweeter settings (Tweeter)
You can select the tweeter installation location and whether or not a tweeter is being used or
not, allowing you to select the optimum time alignment settings automatically.
Touch Tweeter .
● Each time the switch is touched, the
tweeter settings will be changed in the
following order shown below.
NO
Dash
Door
● Touch BACK after making changes.
The time alignment settings will be
saved and system will return to the
previous operation screen.
Rear speaker position selection (Rear SP)
You can select the rear speaker installation location, allowing you to select the optimum time
alignment settings automatically.
Touch Rear SP .
● Each time the switch is touched, the
rear speaker position settings will be
changed in the following order shown
below.
Door
Others
● Touch BACK after making changes.
The time alignment settings will be
saved and system will return to the
previous operation screen.
If the front speakers have been installed to the dash panel, you can set the tweeter
setting to “Dash” even if no tweeter has been installed.
62
Setting sub woofer
When a sub woofer is connected, the preferred output level for the audio can be set.
Touch Woofer in the Time
Alignment screen.
I
II
III
IV
V
Phase selection (NON-F Phase)
The merging of sound between the front and rear speakers and the woofer can be improved
by selecting the phase.
Switch to a phase which lets the speakers combine without any disharmony.
Touch Phase to select NORMAL
or REVERSE.
● NORMAL: Normal phase
REVERSE: Reverse phase
● Touch BACK after making changes.
The phase selection will be saved and
system will return to the previous
operation screen.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
63
Basic operation
Adjusting sound quality
Woofer output setting
Woofer Output can be stereo or mono. Select the method that matches the output method for
the sub-woofer system that is connected to the unit.
Touch Woofer OUT to select
STEREO or MONO.
● Touch BACK after making changes.
The woofer output setting will be saved
and system will return to the previous
operation screen.
Crossover adjustment (X-Over)
The frequencies for the front and rear speaker high-pass filter (HPF) and woofer low-pass filter
(LPF) can be set within a range of 63 to 200 Hz. (This is the same as the HPF and LPF cutoff
frequencies.)
Touch Freq to select the cut-off
frequency.
● Each time the switch is touched, the
frequency will be changed in the
following order shown below.
63Hz 80Hz 100Hz 125Hz 160Hz 200Hz
64
Touch SLOPE .
● Each time this switch is touched, the
slope will be changed in the following
order shown below.
PASS
6 dB/oct
24 dB/oct
12 dB/oct
18 dB/oct
● Touch BACK after making changes.
The crossover setting will be saved
and system will return to the previous
operation screen.
Woofer output level adjustment
The output level of the woofer can be adjusted.
Touch the
or
.
● The adjustment level has 6 “+” steps
and 6 “-” steps.
: Increase level.
: Decrease level.
● Touch BACK after making changes.
The woofer output level adjustment will
be saved and system will return to the
previous operation screen.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
If no woofer has been connected, set the slope adjustment to “PASS”. (If slope is
set to a setting other than PASS, the low frequency range will not be outptted from
the speakers.)
XIX
65
Basic operation
Setting background screen
The background for the audio operation screen can be changed to a preferred wallpaper.
Setting the Background
Press and hold FUNC until you
hear a beep.
Touch
or
for Background.
● Each time switch is touched, the
Background screen will be changed in
following order shown below.
1
2
3
Importing Background
Background provided by the E-iSERV (website) can be downloaded and used instead of the
pre-set Background. To download Background follow the E-iSERV (website) instructions.
After downloading the data to your PC, copy the data to a “Memory Stick Duo” and import the
data into the deck. (URL: http://www.e-iserv.jp)
Access the E-iSERV (web site). (URL: http://www.e-iserv.jp)
Download a background picture available on the E-iSERV website.
(Follow downloading instructions posted on the site.)
Copy the Background to a “Memory Stick Duo”.
Import into the unit.
Insert the “Memory Stick Duo”
containing the images to be saved.
Press FUNC for less than one
second.
66
● The mode will change to function mode.
If you press the FUNC button once more, function mode will be exited.
Touch DATA .
● The display will change to the menu
screen for data management mode.
I
II
III
IV
Touch PICTURE .
V
VI
VII
VIII
Touch the image file to be read and
saved.
IX
X
● The image for the selected file will be
displayed.
If there are more than 7 files on the
media, touch
or
to search
through the list of image files for the
files you would like to read and save.
XIII
Touch DATA READ .
XIV
XI
XII
XV
XVI
XVII
XVIII
XIX
67
Basic operation
Setting background screen
Touch Background 1 ,
Background 2 or Background 3 .
● The image file that was selected in
above will then be saved.
step
If an image file has already been
saved, it will be overwritten.
● Touch the Cancel to cancel data
saving.
●Do not eject the “Memory Stick Duo” while a file is saved. Otherwise the file data
may become corrupted.
●Data downloaded from the E-iSERV (web site) can be saved in folders on the
“Memory Stick Duo” as follows:
MSFTEN
User creation
PIC
XXXXXXXX.jpg
Automatic creation
File extension
●Files that can be imported into the unit are created automatically when
downloaded from the E-iSERV (web site).
●The file name can be changed using 8 alphameric characters (adding a space for
a character cannot be used).
68
Basic operation
Adjusting/setting the screen
Switching the FUNCTION switch display
Touch switches not frequently used are not displayed in the audio operation screens and DVD
screens. These switches can be displayed as follows.
Touch FUNC .
● The FUNCTION switches appear.
● The FUNCTION switches are different
in each audio mode.
I
II
III
IV
V
● The FUNCTION switches can be
hidden by touching CLOSE .
● If the FUNCTION switches are
displayed, operations corresponding to
other switches cannot be performed.
Hide the FUNCTION switches, then try
the operation again.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
69
Basic operation
Adjusting/setting the screen
Changing the clock settings
Touch switches not frequently used are not displayed in the audio operation screens and DVD
screens. These switches can be displayed as follows.
Press FUNC for less than 1
second.
● The FUNC screen will appear.
Setting the clock display
This turns the clock display on or off.
Touch Clock .
● The clock display turns on and off each
time Clock is touched.
When the clock display is on, the touch
switch display color changes to the
selected switch.
Adjusting the time
This adjusts the time.
Touch
item.
or
for adjust each
To set the clock to 0 minutes (an exact hour), touch the touch switch.
For example:
At 3:29: Touch SET returns to 3:00.
At 3:30: Touch SET advances to 4:00.
70
Quality adjustments can be made for images as with the audio operation screen and DVD or
VTR (optional).
I
Adjusting image quality
Contrast, brightness and other picture settings can be adjusted to match preferences for
viewing DVD video or the audio operation screen.
Press and hold FUNC until you hear a beep.
II
III
IV
● The PICTURE screen will appear.
V
VI
VII
VIII
● When adjusting audio operation screen
● When adjusting DVD/VTR screen
Bright
Touch
X
to increase brightness, or
to decrease brightness.
Contrast
Touch
to increase contrast, or
to decrease contrast.
to increase red, or
to increase green.
for a darker color, or
XII
XIV
XV
Tint (for DVD/VTR screen only)
Touch
XI
XIII
Color (for DVD/VTR screen only)
Touch
IX
for a lighter color.
XVI
XVII
XVIII
XIX
71
Basic operation
Adjusting/setting the screen
Switching screen mode
Touch WIDE .
Touch NORMAL , WIDE1 ,
WIDE2 or WIDE3 .
● This selects the wide mode.
72
I
II
III
NORMAL mode
The screen is shown with a vertical to
horizontal ratio of 3 to 4. The side edges
are black.
WIDE 1 mode
The screen is shown with a vertical to
horizontal ratio of 3 to 4 and is expanded
in the left and right directions. A wide
screen effect can be displayed without
any image loss.
IV
V
VI
VII
VIII
IX
X
XI
WIDE 2 mode
Only the left and right edges of the screen
are stretched out. However, the vertical to
horizontal ratio of 3 to 4 is maintained at
the center of the screen to provide a
comfortable wide screen image.
WIDE 3 mode
The screen is expanded in both the
vertical and horizontal directions by the
same ratio. The image is clipped slightly
at the top and bottom edges.
XII
XIII
XIV
XV
XVI
XVII
Viewing of wide screen modes is permitted when limited to the personal
entertainment of the user, but exercise caution when using technologies such as
image compression and expansion for the purpose of commercial benefit or public
presentation. This may infringe upon the rights of the copyright holder protected by
applicable copyright law.
XVIII
XIX
73
Basic operation
Others
Setting the steering switch function
The vehicle’s factory loaded steering switch becomes inoperable when the this unit is
installed. The E-iSERV (web site) provides software that enables steering switch operation.
Import this software into this unit.
For details, contact the store from which you purchased your unit. Depending on your
vehicle’s make and model, material downloaded from the website may not be compatible with
your steering switch.
Software for the steering switch can be downloaded and imported into the deck as follows:
Access The E-iSERV (web site). (URL : http/www.e-iserv.jp)
Download the steering switch software following instructions
provided on the E-iSERV (web site). (Because material available
on the website may not be compatible with the steering switches
found on some automobiles, make sure to check the website for
details about compatibility.)
Copy the downloaded software to “Memory Stick Duo”.
Import the data into the deck from the “Memory Stick Duo”.
(For details about importing into the unit, see next page.)
The steering switch can now be operated.
Consult the store from which you purchased this unit about compatibility and setup procedures.
74
Reading steering switch data
The steering switch data that has been downloaded from E-iSERV (web site) to a “Memory
Stick Duo” can be loaded in the this unit.
Insert the “Memory Stick Duo”
containing the steering switch data
to be saved.
Press FUNC for less than 1
second.
I
II
III
IV
V
VI
Touch DATA .
VII
VIII
IX
X
Touch Steering SW .
XI
XII
XIII
XIV
A message will appear to confirm
the data transfer.
● Touch Yes to update the data.
● Touch No to return to the screen in
step
.
XV
XVI
XVII
XVIII
XIX
75
Basic operation
Others
Compatibility with various switches
The compatibility of the deck’s various modes and the steering switches installed on your
vehicle are as follows:
Source
Switch*
MODE
Tune UP
Tune DOWN
Radio
TV
CD
DVD
Change source
Change source
Change source
Tune UP (Short tap)
TRACK UP (Short tap)
SEEK UP (Hold)
FAST UP (Hold)
Tune DOWN (Short tap) TRACK DOWN (Short tap)
SEEK DOWN (Hold)
FAST DOWN (Hold)
Chapter DOWN
VOL UP
VOL UP
VOL UP
VOL UP
VOL DOWN
VOL DOWN
VOL DOWN
VOL DOWN
Source
Switch*
MODE
Tune UP
Tune DOWN
MP3/WMA
Others
Change source
Change source
FILE UP (Short tap)
FAST UP (Hold)
FILE DOWN
(Short tap)
–
–
FAST DOWN (Hold)
VOL UP
VOL UP
VOL UP
VOL DOWN
VOL DOWN
VOL DOWN
*: Switch names may change depending on vehicle make and models.
76
Chapter UP
Setting the Guide tone
The guide tone that is emitted when touching a panel switch or touch switch can be set.
Press FUNC for less than 1
second.
Touch Guide Tone in the
FUNCTION screen.
● Touching the switch toggles between
ON and OFF.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
●Set the volume at a level which will not adversely affect safety while driving.
●The volume level may change after switching sources. Adjust the volume to
match the source being used.
●A volume adjustment made during DVD playback will not affect other sources.
The volume will return to the level set for the source used prior to the DVD.
XVIII
XIX
77
Basic operation
Others
Displaying Amplifer Status (E-AMP)
If a DSP Amp is connected, the status of the DSP amp will be displayed.
Press FUNC for less than 1
second.
Touch E-AMP .
● The DSP Amp status screen will
appear.
78
Screen lock settings
Screen lock enables the unit to switch to a separate audio source such as radio or CD while
continuing to display a DVD or TV image.
Select the screen lock image settings.
Press FUNC until you hear a
beep.
I
II
III
IV
Touch AV Setting .
V
VI
VII
VIII
Touch Lock to select Lock ON/
OFF.
IX
● Touching the switch toggles between
ON and OFF.
X
● Touch BACK after making settings.
The screen lock settings will be saved
and system will return to the previous
operation screen.
XI
Touch Picture to select an image.
● Each time the switch is touched, the
image is changed in the following order
shown below.
DVD
VTR1 (TV)
VTR2 (TV)
● The selected image will appear on the
left side of the screen.
● Touch BACK after making changes.
The screen lock settings will to save
and system will return to the previous
operation screen.
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
79
How to operate the tuner
How to use the AM/FM radio
BAND switches
Preset switches
FUNCTION switch
• Station Name
• ASM
• Info
MENU
button
POWER
button
SOURCE
button
TUNE·TRACK
button
Listening to the AM/FM radio
Listening to the radio using touch switches
Press MENU .
Touch AM for AM radio, or FM for FM radio.
Listening to the radio using panel button
Press the SOURCE to select the AM or FM.
Switching the band
Touch BAND .
● Each time the switch is touched, the radio bands will be changed in the following order.
FM1
FM2
FM3
AM
When an optional HD Radio tuner unit is connected, digital broadcasts have
reception priority. (U.S.A. only)
80
Selecting radio stations
Manual selection
Press
or
.
● Pressing the switch once moves the frequency one step up or down.
●
(up) : Raises the frequency
(down) : Lowers the frequency
Automatic selection
Press and hold
or
until you hear a beep.
● The station that is closest to the current frequency will be searched for automatically,
and searching will stop when the station is received. To stop the search before a
station is found, press the button again.
Selection using preset switches
I
II
III
IV
V
VI
VII
VIII
Touch a preset switch that already has a station recorded.
IX
● See “Saving radio stations” on next page for more information.
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
If the reception for a particular station is weak in the area you are in, the automatic
selection may not work.
81
How to operate the tuner
How to use the AM/FM radio
Saving radio stations
There are two modes for saving radio stations, manual and ASM. These modes operate
independently.
Saving manually
Use manual tuning or automatic tuning to select the station to be saved.
Choose a preset switch and touch it until you hear a beep.
● The radio station (frequency) is set. Touch the preset switch to tune in the selected
station.
Saving with ASM
Touch FUNC .
Touch ASM until you hear a beep.
● The ASM function will activate and start automatically selecting stations. You will hear
a beep when the automatic selection of stations is completed. Touch ASM again to
switch the display back to the broadcast station originally saved.
Changing stations saved by ASM
Use manual tuning or automatic tuning to select the station to be saved.
Touch the preferred preset switch until you hear a beep.
●ASM may not automatically receive stations if radio waves in the surrounding
area are weak.
●A frequency saved with the tuning switch may not match the frequency saved
with ASM even though the signal is received from the same station.
●Due to conditions for receiving radio waves, saved stations may differ even when
the ASM switch is operated repeatedly in the same location.
●Up to six stations with good signal reception are automatically saved in order of
frequency (low to high).
●When less than six stations capable of reception are found, nothing is saved for
the remaining preset switches.
82
Checking preset stations
This recalls all the stations that have been preset either automatically or manually and plays
them each for 5 seconds.
I
Touch FUNC .
II
Touch ASM for less than 1
second.
III
● “P.SCAN” will be displayed, and the
preset stations will each be played
back for 5 seconds.
Touch ASM for less than one
second.
● The station that was being played
when the switch was touched will then
be played continuously.
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
83
How to operate the tuner
How to use the AM/FM radio
Creating a station name
A station name can be created and displayed.
Touch FUNC .
Touch Station Name for less than
1 second.
● The screen will switch to the station
name setting mode. Default character
type is upper-case alphabet.
Touch one of the switch ABC ,
abc , 123 , !”# .
● ABC : Upper-case alphabet
abc :Lower-case alphabet
123 :Numerical
!”# :Symbol
Touch the character touch switch.
●Touch the RTN to delete the character that was just entered.
●A maximum of 16 characters may be entered per title.
●The station name entered may not be displayed when an optional HD radio tuner
unit is connected.
84
Upper case characters,
alphabet characters
Lower case characters,
alphabet characters
I
II
III
Numerical character
Symbol
IV
V
VI
VII
Touch the ENTER touch switch to enter station name setting mode.
The station name is now memorized.
Deleting a previously created station name
Touch FUNC .
Press and hold Station Name
until you hear 2 beeps in
succession.
● The station name has now been
deleted.
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
85
How to operate the tuner
How to use the AM/FM radio
Turning off the radio
Press
.
● Press
again to turn on the radio
and to resume the radio station
received prior to turning power off.
86
How to operate the CD player
How to use the CD player
I
FUNCTION switch
• TITLE
• TEXT
• REPEAT
• RANDOM
MENU
button
II
III
IV
V
VI
SOURCE
button
TUNE·TRACK
button
VII
VIII
Listening to a CD
Playback starts when a CD is inserted into the disc slot.
Listening to a CD using the touch switches
Press MENU when a CD has been inserted.
Touch CD .
● Playback will begin.
Listening to a CD using the panel buttons
Press the SOURCE to select the CD source when a CD has been inserted.
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
●Titles and track names can be displayed when they are recorded on a CD. Up to
16 characters can be shown in the display.
●Only characters recorded by ASCII code can be shown on the CD-TEXT display.
●The CD-TEXT display may not be able to show characters for discs recorded
with many title characters.
●There may be occasions when CD-R/RW CD-TEXT cannot be displayed.
XVIII
XIX
87
How to operate the CD player
How to use the CD player
Selecting a track
You can jump to the opening of a track you want to hear.
Press
●
or
.
(up) : Selects next track
(down) : Selects previous track
Fast-forwarding/rewinding
It is possible to fast-forward/rewind the track being played.
Press and hold
●
or
until you hear a beep.
(up) : Fast-forward
(down) : Rewind
If you hear a beep while rewinding (fast-forwarding), the unit has switched to fastforward (rewind) mode and will continue until you remove your finger from the button.
Repeating a track
Touch FUNC .
Touch REPEAT .
● Repeats the current track.
● The track will repeat until the function is canceled. Touch REPEAT again to cancel.
Playing tracks in random order
Touch FUNC .
Touch RANDOM .
● Plays tracks in random order.
● Random playback will continue until the function is canceled. Touch RANDOM
again to cancel.
● At the end of each track the system arbitrarily chooses which track to play next. As a
result, it is possible for the same track to be played multiple times in a row.
88
Creating a title for a CD
A CD title can be created and displayed.
Touch FUNC .
Touch TITLE for less than 1
second.
● The screen will switch to the disc title
setting mode. Default character type is
upper-case alphabet.
I
II
III
IV
V
Touch one of the switch ABC ,
abc , 123 , !”# .
VI
● ABC : Upper-case alphabet
VII
abc :Lower-case alphabet
123 :Numerical
!”# :Default character type is
symbol
Touch the character touch switch.
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
●Touch the RTN to delete the character that was just entered.
●A maximum of 16 characters may be entered per title.
●No CD text disc can be set.
XIX
89
How to operate the CD player
How to use the CD player
Upper case characters,
alphabet characters
Lower case characters,
alphabet characters
Numerical character
Symbol
Touch the ENTER touch switch to exist disc title setting mode.
The disc title is now memorized.
Deleting a previously created title
Touch FUNC .
Press and hold TITLE until you
hear 2 beeps in succession.
● The title has now been deleted.
90
Displaying CD TEXT by scrolling
CD TEXT (such as disc titles and track titles) stored in the memory can be displayed. A
maximum of 16 characters are displayed on the display area at one time. When the CD TEXT
exceeds 16 characters, it is displayed by scrolling.
After the disc title is displayed by scrolling, track titles are displayed by scrolling.
The title display will be fixed after track titles are scrolled.
I
II
III
Touch FUNC .
Touch TEXT .
IV
V
VI
VII
VIII
Turning off the CD player
Press
.
● Press again to resume playback.
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
●This function cannot be used when no CD titles or track titles are displayed on
the display screen of this unit.
●Depending on the equipment used for entering titles, the titles may not be
displayed properly.
●Some title characters may not be displayed for some discs.
XVIII
XIX
91
How to operate the MP3/WMA player
How to use the MP3/WMA player
For safety considerations, some functions are disabled while the vehicle is in motion.
File change
switches
Folder change
switches
FUNCTION switch
• REPEAT
• RANDOM
switch
MENU
button
HOME switch
POWER
button
SOURCE
button
TUNE·TRACK
button
Example of MP3/WMA file structure
Explanations are based on this example of MP3/WMA file structure.
Folder
MP3/WMA audio file
1st
level
2nd
level
3rd
level
4th
level
It is not possible to playback WMA files protected by a DRM (Digital Rights
Management) system or protected recordings (licensed).
92
Playing MP3/WMA
Playback starts automatically when a CD is inserted into the disc slot.
I
Playing MP3/WMA using the touch switches.
II
Press MENU when a disc has been inserted.
Touch
CD
III
.
● Playback will begin.
IV
● The CD player screen will be shown for about 2 seconds as the system checks
whether the inserted CD is a music CD or an MP3/WMA.
V
● Normally, tracks are played back in the order
● When multiple MP3/WMA files and folders are on the same level, they are played in
ascending order by folder and file names.
Playing MP3/WMA using the panel buttons
Press the SOURCE to select the CD source when CD has been inserted.
.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
93
How to operate the MP3/WMA player
How to use the MP3/WMA player
Selecting a music file
A music file located within a folder can be selected.
Selecting with file change switches
Touch the music file.
● The currently selected file name and folder name will be shown in the display.
● When 4 or more music files are located in the same folder, touch
or
to show
data not currently displayed. (This function is not available when the vehicle is in
motion)
Selecting with TUNE/TRACK button
When several music files are located in the same folder, the next music file or previous music
file can be selected with the track selection (track start point).
Press
●
or
.
(up): Selects next music file
(down): Selects previous music file
Selecting a folder
A folder located within a disc can be selected.
Touch the folder.
● The currently selected folder name will be shown in the display.
● When 4 or more folder are located in the disc, touch
or
to show data not
currently displayed. (This function is not available when the vehicle is in motion)
If music data and MP3/WMA data have been recorded on the same disc, playback
is not possible.
94
Fast-forwarding/rewinding
It is possible to fast-forward/rewind within the current file.
Press and hold
●
(up)
or
until you hear a beep.
: Fast-forward
(down): Rewind
If you hear a beep while rewinding (fast-forwarding), the deck has switched to the fastforward (rewind) mode and will continue until you remove your finger from the button.
Changing display of the current level
The folder level can be switched and displayed.
Touch
or HOME .
●
: Displays the next folder level up.
● HOME
: Displays the level of the file currently being played.
Displaying the current level
Displays the file currently being played.
Touch HOME .
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
95
How to operate the MP3/WMA player
How to use the MP3/WMA player
Repeating the same music file or folder
Repeating the same music file
Touch FUNC .
Touch REPEAT for less than one second.
● Repeats the current file.
● The file will repeat until the function is canceled. Touch REPEAT again to cancel.
Repeating the same folder
Touch FUNC .
Touch REPEAT until you hear a beep.
● Repeats the current file.
● The file will repeat until the function is canceled. Touch REPEAT again to cancel.
96
Playing music files in random order
Playing music files on folder in random order
Touch FUNC .
Touch RANDOM for less than one second.
● Files will be randomly selected from among all files at the folder currently being played.
● Plays files in random order.
● Random playback will continue until canceled. Touch RANDOM again to cancel.
● Touch REPEAT during random playback to repeat the file currently being played.
Touch REPEAT again to return to random playback.
● At the end of each file, the system arbitrarily chooses which file to play next. As a
result, it is possible for the same file to be played multiple times in a row.
Playing music files on CD in random order
Touch FUNC .
Touch RANDOM until you hear a beep.
● Randomly selects and plays files using all files on the disc.
● Plays files in random order.
● Random playback will continue until canceled. Touch RANDOM again to cancel.
● Touch REPEAT during random playback to repeat the file currently being played.
Touch REPEAT again to return to random playback.
● At the end of each file, the system arbitrarily chooses which file to play next. As a
result, it is possible for the same file to be played multiple times in a row.
Turning off the MP3/WMA player
Press
● Press
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
.
again to resume playback.
XVII
XVIII
See page 92 for an example MP3/WMA file structure.
If
of the third level is being played and the display shows the folder and files of
the second level (
, and
), touch HOME to display the folder and file of
).
the third level (
and
XIX
97
How to operate the MP3/WMA player
How to use the MP3/WMA player
About MP3/WMAs
MP3 (MPEG Audio Layer III) is a standard format for audio compression technology. By using
MP3 a file can be compressed to one-tenth the size of the original.
WMA (Windows MediaTM Audio) is format for audio compression technology. WMA files can
be compressed to a size smaller than MP3 files. This unit has limitations on MP3/WMA file
standards and recorded media and formats that can be used.
Playable MP3 file standards
● Supported standards
: MPEG1 Audio Layer III
● Supported sampling frequencies: 44.1, 48 (kHz)
● Supported bit rates
: 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps)
* Supports VBR.
* Does not support free format.
* Bit rates vary for MPEG-1 and MPEG-2.
● Supported channel modes
: stereo
Playable WMA file standards
● Supported standards: WMA Ver. 7
WMA Ver. 8
WMA Ver. 9
● Supported sampling frequencies: 32, 44.1, 48 (kHz)
● Supported bit rate: 48, 64, 80, 96, 128, 160, 192, 256, 320 (kbps)
* Supports VBR (48~192 kbps).
* Does not support lossless compression.
* Does not support WMA files recorded at a frequency of 48 kHz with a bit
rate of 48 kbps.
Use 128 kbps or lower for the MP3 bit rate. If the bit rate exceeds 128 kbps, there
may be a skipping type effect during MP3 playback.
98
ID3/WMA tags
MP3/WMA files have an “ID3/WMA Tag” that allows input of information so that data such as
song title and artist can be saved. This unit supports ID3v. 1.0, 1.1 and WMA tags.
Media
Media capable of playing MP3 include CD-ROM, CD-R and CD-RW discs.
Compared to CD-ROM media commonly used for music discs, CD-R discs are fragile in high
temperature/high humidity environments and sections of the CD-R may become incapable of
playback. Fingerprints or scratches on the disc may prevent playback or cause skipping.
I
II
III
IV
Sections of a CD-R may deteriorate if left inside a vehicle for long periods of time.
V
It is also recommended that CD-R discs be kept in a light-blocking case because the discs are
vulnerable to ultra-violet light.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
99
How to operate the MP3/WMA player
How to use the MP3/WMA player
Format of discs
The format of discs to be used must be ISO9660 Level 1 or Level 2. Also, be sure to record in
“MODE 1”. Discs recorded in “MODE 2” are not supported.
MP3 files recorded in formats other than those outlined above may result in files that cannot
be played normally and file names and folder names that do not display properly.
The following additional limitations apply:
● Maximum directory layers
: 8 levels
● Maximum characters for folder names/file names: 31 (including “.” and the 3 letters of the
file extension)
● Allowable characters for folder names/file names : A-Z, 0-9, _ (underscore), all ASCII
characters
● Number of files/folders possible in a single folder : 512*
*: Each file is counted as one file, even if it is not an MP3/WMA file (i.e. files with extensions
other than “.MP3/.WMA”).
100
File names
Only files with the MP3/WMA file extension “.mp3”, “.wma” can be recognized as MP3/WMA
and played. Be sure to save MP3 files with the “.mp3” file extension. Be sure to save WMA
files with the “.wma” file extension. The “MP” or “WMA” letters of the file extension will be
recognized whether entered as uppercase letters or lowercase letters.
Multi-sessions
Multi-sessions are supported, and playing of CD-R and CD-RW discs with annotated MP3/
WMA files is possible. However, when “Track at once” has been written, close the session or
process the warning message. Standardize the format of each session without changing the
format.
Playing MP3
When a disc with recorded MP3/WMA files is inserted, the deck first checks all the files on the
disc. No sound is output while the deck is checking the files on the disc. It is recommended
that the disc be recorded without files other than MP3/WMA files and without unnecessary
folders in order to speed up the checking of disc files by the deck.
MP3/WMA playing time display
I
II
III
IV
V
VI
VII
VIII
IX
It is possible that playing time will not be correct, depending on the writing condition of the
MP3/WMA file.
X
* It is possible that playing time will not be correct when VBR Fast Up/Down is operated.
XI
Display order of MP3 file/folder names
Names of MP3 folders and files within the same level are displayed in the following order.
1. MP3 files displayed first, by ascending order of numbers, letters.
2. Folders displayed next, by ascending order of numbers, letters.
XII
XIII
XIV
XV
XVI
XVII
XVIII
If the “.mp3”, “.wma” file extension is attached to a file other than an MP3/WMA file,
that file will be mistakenly recognized by the unit as an MP3/WMA file and played,
resulting in noise and static that can damage the speakers. Do not attach the
“.mp3”, “.wma” extension to any non-MP3/WMA files.
XIX
101
How to operate the MP3/WMA player
How to use the MP3/WMA player
Making and playing MP3/WMA files
MP3/WMA files created by recording broadcasts, records, audio recordings, video recordings
or live performances cannot be used for purposes other than personal entertainment without
permission of the copyright holder as set forth in copyright law.
Downloading MP3/WMA music from internet
There are many kinds of sites that distribute MP3/WMA files on the Internet, such as “pay per
download” online shopping sites, “try before you buy” listening sites and free download sites.
Follow the rules for each site (such as paying fees) and download according to site
instructions.
Converting CD music to MP3/WMA files
Prepare a computer with commercially available MP3/WMA encoding software (conversion
software). (Some encoding programs available on the Internet do not require payment.) Music
data files in MP3/WMA format can be made by inserting the music CD into the CD-ROM drive
of the computer and following the procedures of the MP3/WMA encoding software to
compress the songs of the music CD. A 12cm music CD (having a maximum of 74 minutes of
recording/650MB of data) can be compressed to 65MB (about 1/10 of the original size).
When writing to CD-R/RW
MP3/WMA files can be recorded on CD-R/RW by using a CD-R/RW drive connected to a
computer. Record by setting the recording format of the recording software to ISO9660 level 1
or level 2 (not including extension format).
Select CD-ROM (mode 1) for the disc format. Discs recorded with CD-ROM xA (mode 2)
cannot be played on this deck.
When playing back CD-R/RW
Insert a CD-R/RW containing recorded MP3/WMA files. The system will automatically
determine whether the disc is a music CD or a CD-R/RW with MP3/WMA files and begin
playing the disc. A music CD recorded onto a CD-R/RW can also be played. However,
depending on the type of disc being used, playback may not be possible.
●A fixed bit rate of 128kbps and sampling frequency of 44.1kHz is recommended
for obtaining stable audio quality at playback.
●Depending on the characteristics of a disc, the system may not be able to read
CD-R and CD-RW discs.
●Because there are many types of MP3/WMA encoding software available,
including commercial and freeware programs, audio quality may deteriorate,
noise may be generated when playing starts and some recordings may not play,
depending on the condition of the encoder and the file format.
●When files other than MP3/WMA files are recorded on a disc, the system may
take some time to recognize the disc or it may not play.
102
How to operate the optional CD changer
How to use the CD changer
An optional CD changer can be connected and used.
I
Disc change
switches
II
FUNCTION switch
• REPEAT
• RANDOM
• TITLE
III
IV
MENU
button
V
VI
POWER
button
SOURCE
button
TUNE·TRACK
button
VII
VIII
IX
Listening to a CD
Listening to a CD using the touch switches
X
XI
Press MENU .
XII
Touch CDCH .
Listening to a CD using the panel buttons
Press SOURCE to select the CD changer source when optional CD
changer has been connected.
XIII
XIV
XV
XVI
XVII
XVIII
When two CD changers are connected, CDCH
the CD changer operation screen. Touch CDCH
second disc changer.
(
(
: number) is displayed on
: number) to switch to the
XIX
103
How to operate the optional CD changer
How to use the CD changer
Selecting a track
See “How to use the CD player” (Page 88).
Fast-forwarding/rewinding
See “How to use the CD player” (Page 88).
Selecting a CD
A CD can be selected from among all the discs in the changer.
Touch one of the disc change switches.
● The number for the selected CD will change color.
Repeating a track or CD
Repeating the current track
See “How to use the CD player” (Page 88).
Repeating the current CD
Touch FUNC .
Touch REPEAT until you hear a beep.
● Touch once to continue repeating the CD. Repeat will continue until canceled. Touch
REPEAT again to cancel.
●A disc change switch is displayed for each disc tray in the changer but only the
disc change switches that correspond to a currently loaded tray can be selected.
●No operation is possible when there are no discs loaded into the CD changer.
104
Playing tracks in random order
Playing tracks on current CD in random order
I
See “How to use the CD player” (Page 88).
II
Playing tracks on all CDs in random order
Touch FUNC .
Touch RANDOM until you hear a beep.
● Setting once will start random playback which will not stop until the function is
canceled. Touch RANDOM again to cancel.
● At the end of each track the system arbitrarily chooses which track to play next. As a
result, it is possible for the same track to be played multiple times in a row.
III
IV
V
VI
VII
Creating a title for a CD
VIII
See “How to use the CD player” (Page 89).
IX
Deleting a previously created title
See “How to use the CD player” (Page 90).
Turning off the CD changer
Press
● Press
.
again to resume playback.
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
105
How to operate the DVD player
Before using the DVD player
This unit can output the high quality images and high quality digital sound of DVD videos. It is
also possible to switch between different languages recorded on the DVD video (dubbing,
subtitles, etc.), and with videos having several angles of the same scene recorded, the
preferred angle can be selected and played.
DVD video characteristics
About multiple languages
Some DVD discs have dialog recorded in several different languages, and the language can
be switched during playback in the same way as multilingual TV broadcasts.
This river, which runs through
the center of the town is...
Cette riviere, laquelle court au
travers le centre de la ville est...
About multiple angles
Some DVD discs have a single scene recorded from several different angles (multiple angle),
and the preferred angle can be switched during playback.
* Depending on the disc, multiple angles may not be recorded.
The angle of the image is changed.
This unit includes copyright protection technology used in accordance with US
patents and other intellectual property rights owned by Macrovision Corporation
and other entities. Use of this copyright protected technology requires approval
from Macrovision Corporation and the technology must not be used for audiovisual
purposes aside from general household use without special approval from
Macrovision Corporation. Modification and disassembly of this technology is
prohibited.
106
About subtitles
Some DVD discs have subtitles recorded in several different languages, and the subtitles can
be switched during playback. The video can also be played without any subtitles displayed.
I
II
III
IV
V
VI
About discs
VII
About playable discs
This unit conforms to NTSC color television methods, so please use discs that display “NTSC” on
the disc or package.
Playable disc types and their marks
Size/Playing surface
Maximum playing time
12cm/single-sided
single-layer
double-layer
<MPEG2>
133 min.
242 min.
12cm/double-sided
single-layer
double-layer
266 min.
484 min.
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
107
How to operate the DVD player
Before using the DVD player
About region codes of playable discs
Some DVD discs display a 1 (“Region Code”). This mark (a number) shows the
geographical region where the disc can be played. This unit can only play discs with region
codes “1” (North America), “3” (Asia) “4” (Australia) or “ALL”. If you play discs with any region
code other than those shown above, a “This disc cannot be played” message is displayed. It is
possible that discs bearing no region code can not be played as a result of geographical
restrictions.
About marks displayed on discs
The following marks may be displayed on a DVD disc or its package.
Mark
Meaning
3
Shows number of voice tracks.
2
Shows number of subtitle languages.
Shows number of filmed angles.
3
16:9 LB
4:3
ALL
1
3
Shows available aspect ratio (television screen horizontal to
vertical ratio).
●“16 : 9” is wide screen, “4 : 3” is standard screen.
Shows playable region code.
●ALL indicates worldwide. A number indicates a specific
region code. “1” is the region number for North America.
“3” is the region number for Asia.
“4” is the region number for Australia.
4
The playing condition is determined by the creator of the DVD/software. Some
functions may not perform during operation because the unit is playing the disc
according to content specifications intended by the software creator. Be sure to
consult the explanatory material provided with the disc to be played.
108
About DVD disc structures
Videos and tracks recorded on a DVD are divided into many segments.
Large segments are called “titles”, and each title has a number (“title number”). Title segments
are further divided into smaller segments called “chapters”, and each chapter has a number
(“chapter number”).
Title 1
DVD-Video
Title 2
I
II
Chapter 1
III
Chapter 2
IV
Chapter 3
V
Chapter 1
VI
Chapter 2
Chapter 3
VII
VIII
Chapter 1
Title 3
Chapter 2
Chapter 3
Title number
Chapter number
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
109
How to operate the DVD player
How to use the DVD player
For safety reasons, DVDs can only be played when the ignition is switched to ON or ACC and
the vehicle is completely stopped with the parking brake applied. (Only sound is output if a
DVD is played while the car is in motion.)
Chapter number
Playing time
MODE button
SET switch
PWR button
ANGLE button
ENTER button
SUB TITLE
button
TOP button
AUDIO button
MENU button
PLAY button
STOP button
PAUSE button
POWER
button
SOURCE
button
TUNE·TRACK
button
Watching a DVD
Playback starts automatically when a DVD is inserted into the disc slot.
Watching a DVD using the touch switches
Press MENU when a DVD has been inserted.
Touch DVD .
● Playback will begin.
● To display the operation switches (touch switches), touch the screen.
110
CURSOR button
SLOW button
CHAPTER
button
Watching a DVD using the panel buttons
Press SOURCE to select DVD source when a DVD has been inserted.
Waching a DVD using the remote control
Press MODE to select DVD source when a DVD has been inserted.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
●Information for items such as touch switches will be displayed for about 6
seconds. Touch the screen to display again.
●Depending on the disc, automatic playback or playback may not function unless
a menu recorded on the disc is selected. (See “Operating the disc menu” on
page 116)
XVIII
XIX
111
How to operate the DVD player
How to use the DVD player
Operating the video
Playing the video
Playing the video using the touch switches
Touch
.
Playing the video using the remote control
Press
(PLAY)
on the remote control.
Fast-forwarding/rewinding
It is possible to fast-forward or rewind through the video being played.
Fast-forwarding/rewinding using the panel buttons
Press and hold
●
or
until you hear a beep.
(up) : Fast-forward
(down) : Rewind
If you hear a beep while rewinding (fast-forwarding), the deck has switched to the fastforward (rewind) mode and will continue until you remove your finger from the button.
Fast-forwarding/rewinding using the touch switches
Touch
or
.
● If you hear a beep while rewinding
(fast-forwarding), the deck has
switched to the fast-forward (rewind)
mode and will continue until you
remove your finger from the switch.
112
Fast-forwarding/rewinding using the remote control
Press
CHAPTER
until you hear a beep.
: When pressed and released immediately, the picture moves to the next chapter
or track.
When pressed and held (for 1 second or more), the pictures or track are fast-forwarded.
: RewindWhen pressed and released immediately, the picture moves to the
beginning of the current chapter or track.
When pressed and held (for 1 second or more), the pictures or track are
rewound.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
113
How to operate the DVD player
How to use the DVD player
Repeating a chapter
Touch REPEAT .
● Repeat the current chapter.
● The chapter will repeat untill the
function is canceled.
Touch REPEAT again to cancel.
Pausing the video
Pausing the video using the touch switches
Touch
.
Pausing the video using the remote control
Press
(PAUSE)
on the remote control.
● The picture playback will pause.
● To return to normal playback, press
(PLAY)
.
Playing back in slow motion
Press
SLOW
on the remote control.
● The picture is played in slow motion.
● To play back in normal mode, press
114
(PLAY)
.
Stopping the video
Stopping the video using the touch switches
Touch
.
I
II
III
IV
V
Stopping the video using the remote control
Press
(STOP)
on the remote control.
● If you then press
(PLAY)
playback will resume from the point where it was stopped.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
115
How to operate the DVD player
How to use the DVD player
Operating the disc menu
It is possible to use the menu recorded on the disc.
Operating disc menu using the touch switches
Touch TITLE MENU or
TOP MENU .
Touch
,
,
, or
to
select the video you want to play.
Touch ENTER .
Operating disc menu using the remote control
Press TOP button on the remote control.
● The DVD menu will turn on and off each time the button is pressed.
Use the CURSOR buttons to select an item, and then press the ENTER
button on the remote control.
116
Turning off the DVD
Turning off the DVD using the panel buttons
Press
● Press
.
again to resume playback.
Turning off the DVD using the remote control
Press PWR on the remote control.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
Recorded menu items will differ by disc. The disc is played according to its content
so all functions may not be available.
117
How to operate the DVD player
How to use the DVD player
Searching for a desired chapter
It is possible to search for a particular video segment by title and chapter or by menu number
(number for divided segments).
Searching by chapter
Serching by chapter using the panel buttons
Press
●
or
.
Chapter number
(up) : Selects next chapter
(down) : Selects previous chapter
Switching screen display/audio
It is possible to change the language for subtitles and audio, as well as, the display angle for
the video being played.
This function can only be performed with the special remote control.
Changing the angle
When several angles of a scene are recorded on a disc, the angle can be switched.
Press ANGLE on the remote
control when the multiple angle
mark is displayed.
Multi-angle mark
● The angle number will be displayed.
Each time ANGLE is pressed, the angle will change in order from among the
angles recorded on the disc.
118
Switching subtitle language
When subtitles in several languages are recorded on a disc, the subtitles can be switched.
Press SUB TITLE on the remote control.
● The subtitle number will be displayed.
Switching dubbed audio language
If several audio languages are recorded on a disc, the languages can be switched.
Press AUDIO on the remote control.
● The audio number and language will be displayed.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
●Each time SUB TITLE is pressed, the subtitle language will change in order
from among the subtitles recorded on the disc.
●Depending on the disc, it may only be possible to change subtitles in the top
menu.
●Each time AUDIO is pressed, the audio language will change in order from
among the languages recorded on the disc.
Language 1
Language 2
Language…
XIII
XIV
XV
XVI
XVII
●Depending on the disc, it may only be possible to change audio languages in the
top menu.
●The dts format is not supported by this deck, so no audio will be emitted if “dts
audio” is selected on a disc that enable it. In this case, select “Dolby Digital
audio”, which should also be recorded on the DVD video.
●dts is a registered trademark of the US company Digital Theater Systems, Inc.
XVIII
XIX
119
How to operate the DVD player
How to use the DVD player
Setting the DVD player
The language preferences for voices, subtitles and menu display used during DVD playback
can be set in advance. Optional display of the multiple angle mark, viewer restriction and other
functions can also be set.
Touch SET .
Touch the appropriate touch switch
to progress to the next page and
perform settings.
120
Touch switch
Function
Page
Sets the voice language for video playback.
See below
Sets the subtitle language for video playback.
Next page
Menu Language
Sets the language of displayed menus.
page 123
Angle Indicator
Sets display/non-display of multiple angle mark.
page 124
Parental Setting
Restricts the types of DVD videos that can be
played.
page 125
III
Sets screen size.
page 126
IV
Audio Language
Sub Title
Monitor
Setting the audio language
The preferred language for video playback can be selected.
Touch Audio Language in the
FUNC DVD SETTING screen.
I
II
V
VI
VII
VIII
Touch the preferred language.
● Touch OTHER to set a language
IX
other than those displayed on the
screen.
X
XI
Inputting a code
Touch OTHER in the AUDIO
LANGUAGE setting screen.
Input a language code.
● For language codes see “Table of
language codes” on page 128.
Touch ENTER .
XII
XIII
XIV
XV
XVI
XVII
XVIII
After changing settings in the SET UP screen, the DVD will stop if you press one of
the buttons that switch screens ( SOURCE or MENU ) without touching
ENTER . Touch
in the operation screen to start playback again. (See page
112)
XIX
121
How to operate the DVD player
How to use the DVD player
Setting subtitle language
The preferred subtitles for the video playback can be selected.
Touch Sub Title in the FUNC
DVD SETTING screen.
Touch the preferred language.
● Touch OTHER to set a language
other than those displayed on the
screen.
Inputting a code
Touch OTHER in the SUB TITLE
setting screen.
Input a language code.
● For language codes see “Table of
language codes” on page 128.
Touch ENTER .
Language switching cannot be performed if the selected language is not recorded
on the disc.
122
Setting menu language
Allows selection of a preferred menu language from those recorded on the disc.
Touch Menu Language
in the FUNC DVD SETTING
screen.
I
II
III
Touch the preferred language.
● Touch OTHER to set a language
IV
other than those displayed on the
screen.
V
VI
Inputting a code
Touch OTHER in the MENU
LANGUAGE setting screen.
Input a language code.
● For language codes see “Table of
language codes” on page 128.
Touch ENTER .
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
Language switching cannot be performed if the selected language is not recorded
on the disc.
123
How to operate the DVD player
How to use the DVD player
Setting display of multi-angle mark (angle selection mark)
The multi-angle mark can be set to display/not display during video playback.
Multi-angle mark
Touch Angle Indicator
in the FUNC DVD SETTING
screen.
● Touching the switch toggles between
“ON” and “OFF” mode.
Touch ENTER .
Setting the multi-angle mark display to “ON” will display the multi-angle mark in the
upper right corner of the screen when multiple angles are available on the disc.
124
Setting viewer restriction
This function allows viewing restriction to be set so that discs with adult content or violence will
not be available to children. Viewer restriction can be set at different levels to match restriction
ratings.
Touch Parental Setting in the
FUNC DVD SETTING screen.
I
II
III
Enter a pass code (4-digits) by
touching one number at a time.
IV
Touch ENTER .
V
VI
VII
Touch the preferred restriction
level.
VIII
Touch ENTER .
IX
X
XI
●Restriction cannot be set for discs that do not have a viewer restriction level
recorded.
●Be sure to enter a pass code number. If a number is not entered, setting viewer
restriction will not be possible.
●The pin code shown in the upper section will be displayed as [----] when a pin
code has not yet been set.
●Once the pass code has been set, the pass code will be required for subsequent
use of this function. Please do not forget the pass code. If you forget your pass
code, the default setting (no pass code set) can be restored by touching RTN
10 times.
●Viewer restriction levels are classified in 3 types.
Level 1 . . . . . . . Plays only DVD software intended for children. (Playing of DVD
software intended for general audiences or adult audiences is
prohibited.)
Levels 2 - 7 . . . Plays only DVD software intended for children or general audiences. (Playing of DVD software intended for adult audiences is
prohibited.)
Level 8 . . . . . . . Plays all DVD software. (Factory setting)
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
125
How to operate the DVD player
How to use the DVD player
Changing video output
Touch Monitor in the FUNC DVD
SETTING screen.
● Each time the switch is touched, the
screen size changes in the order
shown below.
16 : 9
WIDE
4:3
PS
4:3
LB
● 16 : 9 (WIDE)
The video is displayed at normal width. DVD software recorded in 4 : 3 size will be
displayed with black left and right edges or will be expanded to the left and right.
● 4 : 3 (PS)
The video is displayed with right and left edges cut off. DVD software recorded in 4 : 3
size will be displayed exactly at screen size (4 : 3).
● 4 : 3 (LB)
The video is displayed with black upper and lower edges.
DVD software recorded in 4 : 3 size will be displayed exactly at screen size (4 : 3).
Touch BACK .
There are no problems with using this function as long as the customer views
images privately in wide-screen format. However, if the images are compressed or
enlarged for viewing for any commercial or public purpose, it may infringe upon the
rights of the copyright holder under applicable copyright laws.
When another monitor such as a rear seat monitor is being used, the size of the
video being displayed in the rear seat monitor will differ according to the video
output size set by the deck (front).
126
Switching dual play
When an optional rear monitor is connected, use this function to switch to sources other than
the DVD, such as the Area Shot screen.
I
Touch Dual Play in the FUNC
DVD SETTING screen.
II
● Touching the switch toggles between
ON and OFF.
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
127
How to operate the DVD player
How to use the DVD player
Table of language codes
These codes are used to specify the language for audio tracks, subtitles and on-screen menu
displays.
Input
code
1001
128
Language
Input
code
Language
Input
code
Language
Japanese
0801
Hausa
1721
Quechua
0514
English
0809
Hindi
1813
Rhaeto-Romance
0618
French
0818
Croatian
1814
Kirundi
0405
German
0821
Hungarian
1815
Romanian
0920
Italian
0825
Armenian
1823
Kinyarwanda
0519
Spanish
0901
Interlingua
1901
Sanskrit
1412
Dutch
0905
Interlingue
1904
Sindhi
1821
Russian
0911
Inupiak
1907
Sangho
2608
Chinese
0914
Indonesian
1908
Serbo-Croatian
1115
Korean
0919
Icelandic
1909
Sinhalese
0512
Greek
0923
Hebrew
1911
Slovak
0101
Afar
1009
Yiddish
1912
Slovenian
0102
Abkhazian
1023
Javanese
1913
Samoan
0106
Afrikaans
1101
Georgian
1914
Shona
0113
Amharic
1111
Kazakh
1915
Somali
0118
Arabic
1112
Greenlandic
1917
Albanian
0119
Assamese
1113
Cambodian
1918
Serbian
0125
Aymara
1114
Kannada
1919
Siswati
0126
Azerbaijani
1119
Kashmiri
1920
Sesotho
0201
Bashkir
1121
Kurdish
1921
Sundanese
0205
Byelorussian
1125
Kirghiz
1922
Swedish
0207
Bulgarian
1201
Latin
1923
Swahili
0208
Bihari
1214
Lingala
2001
Tamil
0209
Bislama
1215
Laothian
2005
Telugu
0214
Bengali
1220
Lithuanian
2007
Tajik
0215
Tibetan
1222
Latvian
2008
Thai
0218
Breton
1307
Malagasy
2009
Tigrinya
Turkmen
0301
Catalan
1309
Maori
2011
0315
Corsican
1311
Macedonian
2012
Tagalog
0319
Czech
1312
Malayalam
2014
Setswana
0325
Welsh
1314
Mongolian
2015
Tonga
0401
Danish
1315
Moldavian
2018
Turkish
0426
Bhutani
1318
Marathi
2019
Tsonga
0515
Esperanto
1319
Malay
2020
Tatar
0520
Estonian
1320
Maltese
2023
Twi
0521
Basque
1325
Burmese
2111
Ukrainian
0601
Persian
1401
Nauru
2118
Urdu
0609
Finnish
1405
Nepali
2126
Uzbek
0610
Fiji
1415
Norwegian
2209
Vietnamese
0615
Faroese
1503
Occitan
2215
Volapuk
0625
Frisian
1513
Oromo
2315
Wolof
0701
Irish
1518
Oriya
2408
Xhosa
0704
Scots- Gaelic
1601
Panjabi
2515
Yoruba
0712
Galician
1612
Polish
2621
Zulu
0714
Guarani
1619
Pashto
0721
Gujarati
1620
Portuguese
How to operate the video CD player (Asia only)
How to use the video CD player
A video CD recorded with Video-CD ver. 2.0 can be played on this unit.
A video CD can be watched only if the vehicle is completely stopped in a safe location with
the parking brake set and ignition switch turned ON or ACC. (Only sound can be heard if a
video CD is played while the car is in motion.)
I
II
III
MODE button
IV
PWR button
V
NUMBER button
VI
ENTER button
RETURN button
PLAY button
POWER
button
SOURCE
button
PAUSE button
SLOW button
CHAPTER
button
TUNE·TRACK
button
Watching a video CD
Playback starts automatically when video CD is inserted into the disc slot.
Watching a video CD using the touch switch
Press MENU when video CD has been inserted.
Touch DVD/VCD .
● Playback will begin.
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
Video CD will be play as designed by producer, and may not be played as
operated.
129
How to operate the video CD player (Asia only)
How to use the video CD player
Watching a video CD using the panel buttons
Press SOURCE to select DVD/CD source when video CD has been
inserted.
Watching a video CD using the remote control
Press MODE to select DVD/CD source when video CD has been inserted.
Using the menu screen
When a video CD featuring PBC (Play Back Control) function is played, the menu screen will
be displayed. With the PBC function, original menu items of a disc can be displayed and
operated while PBC disc is played.
Displaying menu screen
The menu screen can be displayed while a video CD featuring the PBC function is played.
Press RETURN on the remote control.
● Switches display to the menu screen.
● When a CD contains more than 1 page of the menu screen, the display can be
switched by pressing
or
of the panel switch or by pressing the
CHAPTER
on the remote control.
Selecting menu list
Enter a menu number with the 0 to 9 number button.
● Entered numbers can be retracted with each pressing of the CLEAR .
Press ENTER .
● Begins playing the selected menu.
130
Advancing to the next scene or returning to the
beginning of the scene being played
The image can be controlled during playback.
This function can be operated by using either the panel buttons or remote control.
Using panel buttons
Press
●
or
for less than 1 second.
IV
(up) : Advances to next track.
(down) : Return to previous track.
Using remote control
●
V
VI
VII
for less than 1 second.
CHAPTER
II
III
● The currently selected track number will be shown on the display.
Press
I
VIII
: Advances to next track.
: Return to previous track.
● The currently selected track number will be shown on the display.
IX
X
Fast-forwarding/rewinding
XI
Using panel buttons
Press
●
or
XII
until you hear a beep.
XIII
: Fast-forward.
: Rewinds.
XIV
● The fast-forward/rewind will continue while
or
rewind action will stop when button is released.
is held. The fast-forward/
XVI
Using remote control
Press
●
CHAPTER
XVII
until you hear a beep.
XVIII
: Fast-forward.
: Rewinds
CHAPTER
● The fast-forward/rewind will continue while
rewind action will stop when button is released.
XV
is held. The fast-forward/
XIX
131
How to operate the video CD player (Asia only)
How to use the video CD player
Specifying a track to playback
A track of your choice is directly selectable.
This function can only be performed with the remote control.
Enter a menu number with the 0 to 9 number button during video CD
playback.
● Entered number can be retracted with each pressing of the CLEAR .
Press ENTER .
● Begins playing the selected track
Pausing/Advancing the video
This function can only be performed with the remote control.
Press
(PAUSE)
during video CD playback.
● The video will pause.
● The video will advance each time
Press
(PLAY)
(PAUSE)
is pressed while paused.
.
● Restarts playback.
Stopping playback
This function can only be performed with the remote control.
Press
Press
(PAUSE)
(PLAY)
.
● Restarts playback.
132
during video CD playback.
Using slow motion
This function can only be performed with the remote control.
Press SLOW during video CD playback.
Press
(PLAY)
.
● Restarts playback.
I
II
III
IV
Turning off the video CD
Turning off the video CD using the panel buttons
Press
● Press
.
V
VI
VII
again to resume playback.
Turning off the video CD using the remote control
Press PWR .
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
133
How to operate the Area Shot function (U.S.A./CANADA only)
Before using the Area Shot
About the Area Shot
Using Area Shot function, maps to destinations and guidance information can be displayed on
your unit if you have set route using the E-iSERV (web site). Current vehicle position can also
be displayed on the map if an optional GPS unit is connected.
The display in this manual may differ from that of the actual product.
134
To use the Area Shot function
In order to use Area Shot, driving instructions such as the direction of travel and the street names
of turn intersections must be downloaded from the E-iSERV (web site) and imported into the unit.
The process is as follows:
Access The E-iSERV (web site). (URL: http//www.e-iserv.jp)
I
II
III
Register as a user. A ePID (User Registration Key) is required when registering. For
details for “Displaying ePID” on page 137.
(To register, follow the instructions provided by the website. Once you have
registered, there is no need to repeat the procedure.)
Login.
Set your start point and destination on the Area Shot page. Address or intersection,
city, state/prov and zip/postal code can be used to search for start points, to set
routes and destinations. Your home can be registered as a memory point. (Follow
the instructions provided on the website.)
* Searching condition may differ depending on the service area.
Download information.
Write the downloaded information to a “Memory Stick Duo”.
IV
V
VI
VII
VIII
IX
X
XI
XII
Import the data written to the “Memory Stick Duo” into the this unit.
(For details, see page 138.)
Area Shot is ready for use.
XIII
XIV
XV
XVI
XVII
XVIII
XIX
135
How to operate the Area Shot function (U.S.A./CANADA only)
Before using the Area Shot
Map data
When using the map data, be aware of actual road conditions and obey traffic rules.
Copying, publishing, or using maps in electronic media without the expressed written
consent is forbidden.
GPS (Global Positioning System)
Developed and operated in the United States, GPS (Global Positioning System), is a
system that locates current position (longitude and latitude) using radio waves beamed
to earth from 3 or 4 GPS satellites.
GPS information may not be available under the following circumstances:
● When GPS satellite radio waves are interrupted by buildings, tunnels, elevated
roads, etc.
● When radio waves are interrupted by objects on or near the GPS antenna.
● In some instances, wave transmission is interrupted by the U.S. tracking control
center during maintenance or upgrades.
● When a digital cellular phone (1.5 GHz) is used near a GPS antenna.
●Be sure to obey all traffic rules and regulations while driving.
●Driving while strictly following guidance instructions may lead to traffic violations
and accidents, due to possible discrepancies between actual road conditions and
map guidance.
●Do not modify this system for use other than that specified herein. Also, do not
deviate from the installation procedures described herein, ECLIPSE will not be
held liable for damages including, but not limited to serious injury, death or
property damage resulting from installations that enable unintended operation.
136
How to operate the Area Shot function (U.S.A./CANADA only)
How to use the Area Shot function
Displaying ePID
ePID is your unit's unique ID. In order to use the E-iSERV (web site), a 16-digit ePID is
necessary.
Press FUNC to display the
FUNCTION screen.
Touch Area Shot .
● If an Area Shot route is already
selected, ePID can be displayed even
if AREA SHOT is pressed.
I
II
III
IV
V
VI
VII
● The ePID will appear.
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
Your ePID is a 16-digit ID composed of number (0-9) and letters (A-F).
137
How to operate the Area Shot function (U.S.A./CANADA only)
How to use the Area Shot function
Reading Area Shot data
The Area Shot data that has been downloaded from E-iSERV (web site) to a “Memory Stick
Duo” can be loaded in the the unit and saved there.
Insert the “Memory Stick Duo”.
Press FUNC to display the FUNC
screen.
Touch Area Shot .
Touch Route Select .
Do not turn the power or ignition switch off while the “Memory Stick Duo” is
reading. Interrupting this reading process may corrupt the data.
138
Touch file name switch to select the
route.
● Touch the
,
to move the list.
● The selected route will be read.
I
● Touch BACK return to the previous
screen.
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
●Data downloaded from the E-iSERV (web site) is saved to folders created in the
“Memory Stick Duo” as shown below.
XIII
XIV
XV
XVI
XVII
●Files that can be imported into your unit are created automatically when
downloaded from E-iSERV (web site)
●All of the searched route maps, guidance information, and POI are stored in
these automatically created files.
●The file name can be changed using 8 alphameric characters (adding a space for
a character cannot be used).
XVIII
XIX
139
How to operate the Area Shot function (U.S.A./CANADA only)
How to use the Area Shot function
Changing Area Shot screen
Once Area Shot data has been acquired, a MAP switch is displayed on the various audio
operation screens.
Touch MAP .
● The Area Shot screen will appear.
● Touch Audio to switch to the audio
operation screen.
140
How to view the Area Shot screen
A map screen like the one shown will appear when the Area Shot screen has been selected.
The map is oriented with north at the top.
I
II
III
IV
V
VI
Guidance information:
Information about guidance points are (traveling direction, street names) displayed as a text.
VII
VIII
Arrows:
Indicates the direction to the guidance point.
POI mark:
Up to 5 POI points in the vicinity of the guidance point can be displayed.
Vehicle position mark:
If an optional GPS unit is connected, your vehicle position will be displayed. The vehicle
position mark will move on the map in accordance to your vehicle's movement.
Guidance points:
The guidance point is shown at the center of the map.
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
The display in this manual may differ from that of the what is actually displayed.
141
How to operate the Area Shot function (U.S.A./CANADA only)
How to use the Area Shot function
Displaying touch switch
The touch switches displayed on the Area Shot screen will disappear if they are not operated
for approximately 6 seconds. Perform the following to redisplay the switches.
Touch screen.
● The touch switches will reappear.
142
Switching the map reduction scale
When the Area Shot data is downloaded from E-iSERV, three maps of different scales for
each guidance point are downloaded. Any one of the three (small-scale, standard, or largescale) can be displayed.
Touch
or
map screen.
II
on the standard
III
● The map will switch to the following:
IV
: large-scale map
: small-scale map
V
● Touch
while the large-scale map is
displayed to return to the standard
map.
VI
VII
● Touch
while the small-scale map is
displayed to return to the standard map.
●Large-scale map
●Standard map
I
●Small-scale map
VIII
IX
X
XI
Displaying the all-route map
A map showing the entire route from starting point to destination can be displayed.
Touch the Route .
● The all-route map is displayed.
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
143
How to operate the Area Shot function (U.S.A./CANADA only)
How to use the Area Shot function
● Touch GuidebP to return to the
previous map screen.
Switching guidance points
After passing each location described in the guidance, it is necessary to switch manually to the
next guidance screen. The previous screen can also be accessed manually and confirmed.
Touch
●
or
.
: To switch to next guidance point.
: To switch to the previous
guidance point.
●Start point
144
●Intersections, etc.
●Destination
Switching text information
The text information display can be switched ON and OFF.
Touch Guide .
● This removes the displayed text
information.
● Touch Guide again to redisplay text
information.
I
II
III
IV
V
Re-scrolling through text information
Text information including intersection, street names, and turn directions can be scrolled
across the screen by switching through the guidance points. A maximum of 32 characters are
scrolled on the display. When scrolling is complete, the first 32 characters are once more
displayed on the screen. To re-scroll, perform the following operation:
Touch Guide until you hear a
beep.
● Guidance information can be rescrolled.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
145
How to operate the Area Shot function (U.S.A./CANADA only)
How to use the Area Shot function
Displaying POI vicinity
POI vicinity information can be displayed on the maps for various guidance points. A single
POI category, such as restaurants or shopping, can be set to be display.
A maximum of 5 POI marks can be displayed in the vicinity of a guidance point. The points are
numbered 1 through 5 beginning with the closest POI to the guidance point.
Selecting POI category
Touch POI .
Touch SET .
Touch POI category.
● Touch
,
to move the list.
● Touch OFF to turn the POI vicinity
display OFF.
146
Touch ENTER .
● POIs from the selected category are
displayed when you return to the map
display screen.
● Press BACK to return to the
previous screen.
I
II
III
Displaying POI vicinity information
POI vicinity information can be displayed as text on the Area Shot screen. The information is
displayed as follows:
● Name
IV
V
VI
● ZIP code
VII
● Address
VIII
● Telephone number
Touch POI .
IX
X
XI
XII
XIII
Touch the POI you wish to display.
XIV
● The selected POI vicinity information
will be displayed.
XV
XVI
XVII
XVIII
XIX
147
How to operate the Area Shot function (U.S.A./CANADA only)
How to use the Area Shot function
● Touch
or
to switch among
text information for the displayed next
page or previous page.
●
: Displays POI vicinity information
for the next page
: Displays POI vicinity information
for the previous page
● Touch OFF to cancel the POI vicinity
display.
When an optional GPS unit is connected
When an optional GPS unit is connected, the following operations are available.
● When your vehicle enters the display/map range of the guidance point, a blinking mark will
appear to indicate the position of your vehicle.
● When the vehicle position mark goes outside of the map display area, a map with the
vehicle position mark is no longer displayed. When this happens, switch to the next
guidance point. For details, see “Switching guidance points” on page 144.
To end Area Shot
Press AREA SHOT .
● The Area Shot can be ended by ejecting the “Memory Stick Duo”.
148
ESN security operating procedure
ESN security operating procedure
About ESN
This unit is equipped with ESN (ECLIPSE Security Network). A preregistered music CD
(Key CD), four-digit security code, or a “Memory Stick Duo” on which all unit functions will
not operate, even by turning the ignition switch to the ACC, ON position, reconnecting
the battery after turning the ignition switch off, or disconnecting the battery during
maintenance.
ESN can be set or cancelled using any of the following methods:
● Key CD security (See page 151)
You can record a specific CD that you have as a “key CD” with the unit, and this CD
can then be used to set and cancel the security settings.
● “Memory Stick” security (See page 155)
You can record a secret code (security code) to “Memory Stick Duo”. This “Memory
Stick Duo” or secret code (security code) with the unit, and this “Memory Stick Duo” or
secret code (security code) can then be matched with the unit to set and cancel the
security settings.
● ACC security (See page 163)
This method can only be used when “Memory Stick” security has already been set.
When ACC security is set, button operations are disabled when the ignition switch is
turned to OFF and then back to ACC.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
149
ESN security operating procedure
ESN security operating procedure
How to switch the security type (Key CD security/
"Memory Stick" security)
You can switch the type of security being used (Key CD security or “Memory Stick” security).
The initial setting is for “Memory Stick” security.
Press FUNC for less than 1 second.
Touch SEC .
● The security setting screen will appear.
Touch SEC .
● Security type will switch from Key CD
security (DISC) l“Memory Stick”
security (MS) in order each time the
switch is touched.
If a security is activated, switching the security type is not available.
150
How to operate the ESN (Key CD) security
How to program the Key CD
Press FUNC for less than 1 second.
Touch SEC .
● The security setting screen will appear.
Touch SET .
● “Please insert disc.” will appear.
I
II
III
IV
V
VI
VII
VIII
Insert the CD into the slot.
● “SECURITY” will appear then the Key
CD is ejected.
IX
X
XI
XII
XIII
XIV
XV
●If a CD has already been inserted, a message appears, and then the front panel
opens and the CD is ejected.
●If security is activated, programming the Key CD is not available.
●If there is a problem with the inserted CD, an “ERROR” message will appear for
two seconds and the CD will be ejected. Reinsert the ejected CD.
●If a CD causes the “ERROR” message to appear twice in a row, a “Please
exchange discs.” message will appear for two seconds. Try another CD.
●Copy Protected CD and MP3/WMA CD-ROM cannot be programmed for Key CD
security.
●The Security indicator will flash whenever the vehicle's ignition is switched off.
XVI
XVII
XVIII
XIX
151
ESN security operating procedure
ESN security operating procedure
How to cancel the Key CD
Press FUNC for less than 1 second.
Touch SEC .
● The security setting screen will appear.
Touch CANCEL .
● “Please insert disc.” will appear.
Insert your Key CD into the slot.
● A “The key disc was cancelled”
message appears, then the Key CD is
ejected.
The Key CD is cancelled.
●If a CD has already been inserted, a message appears, and the CD is ejected.
●This process cancels the protection for the ESN protection.
●If the CD other than the Key CD is inserted, ESN protection will not cancel and
the CD is ejected.
152
How to change the Key CD
First, cancel the existing Key CD.
● Refer to “How to cancel the key CD”.
Next, program a new Key CD.
● Refer to “How to program the Key CD”.
I
II
III
How to resume normal operation (ESN security lock out)
IV
If power is disconnected while ESN security is active (a Key CD was programmed), operation
is disabled until power is restored and the unit unlocked. Follow this procedure to resume
normal operation.
V
When the power is turned on after disconnecting the battery power, a
“SECURITY” message will appear for 2 seconds.
Insert your Key CD.
● If the correct CD is inserted, “The security lock was unlocked.” message will appear for
two seconds and the CD will begin playing.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
●If the incorrect CD is inserted, an “ERROR” (“ERROR” and error number)
message will appear for 2 seconds, after which the CD will be ejected.
●If “ERROR5” (the 5th time an error has occurred) appears, “HELP” will appear,
after which the CD will be ejected. When “HELP” appears, carry out the
operations for an ESN security lock out by following the procedure in “What
happens if an incorrect CD is inserted?” on next page.
●You must be use the same CD used for Key CD programming; a duplicate CD
may not work properly.
XVII
XVIII
XIX
153
ESN security operating procedure
ESN security operating procedure
What happens if an incorrect CD is inserted?
After the 5th incorrect attempt, the display reads “HELP” for 5 seconds.
● After the “HELP” message appears for 5 seconds, serial number will then appear.
Press the FUNC , then SOUND , and hold them for 5 seconds.
● After the “SEC” message will appears for 2 seconds, the rolling code (six digit) will
appear.
Press the FUNC .
● A “DISC” message appears.
You will have 5 more attempts the to insert the correct disc.
Insert the key CD into the slot.
● If the correct CD is inserted, an “OK” message will appear for 2 seconds and the CD
will be ejected.
●After the 5th try and the correct Key CD is not inserted, the display reads
“CALL800”; the unit must be returned to Eclipse to be reset. In this case, please
contact your Eclipse dealer for assistance. For country-specific customer service
information, refer to “How to contact customer service” on page 245.
Your Key CD can be easily forgotten. Write the album name in a reminder note.
●If an incorrect CD is inserted, an “ERR_” (“ERR” and error number) message will
appear for 2 seconds, after which the CD will be ejected.
●This process cancels the protection for ESN deck.
154
How to operate the ESN (“Memory Stick”) security
How to record a security code
Press FUNC for less than 1 second.
Touch SEC .
● The security setting screen will appear.
Touch SET .
● The security code entry screen will
appear.
I
II
III
IV
V
VI
Insert the “Memory Stick Duo” into
the slot.
VII
VIII
Input a security code by touching
switches.
IX
● Enter a four-digit security code using
digits 0 to 9, A to F.
X
XI
XII
Press and hold ENTER .
● The security code is registered in the
unit and security is set. The registered
security code is encrypted and then
written to “Memory Stick Duo”.
XIII
XIV
XV
XVI
XVII
XVIII
XIX
155
ESN security operating procedure
ESN security operating procedure
Eject the “Memory Stick Duo”.
● Refer to “How to eject disc (CD/DVD) or “Memory Stick Duo”” on page 48.
●If a “Memory Stick Duo” has already been inserted, a “MS EJECT” message
appears. In this case, eject the “Memory Stick Duo” and insert it again. (Refer to
“How to eject disc (CD/DVD) or “Memory Stick Duo”” on page 48 for details on
ejection of the “Memory Stick Duo”.)
●If the security is already activated, recording the security code function is not
available.
●When the security code is registered using a “Memory Stick Duo” that contains
several kinds of data, such as music, etc., be careful not to clear the recorded
data by formatting the “Memory Stick Duo”.
156
How to cancel the “Memory Stick” security
The security function can be canceled when the security code that has been recorded with the
deck is entered and verified.
Canceling the security function can be done by entering the security code into the unit, or by
using the “Memory Stick Duo”.
Canceling the security function by entering the security code
I
II
III
Press FUNC for less than 1 second.
IV
Touch SEC .
V
● The security setting screen will appear.
Touch CANCEL .
● The security code entry screen will
appear.
VI
VII
VIII
IX
X
A security code is entered by
touching switches.
XI
● Enter a four-digit security code using
digits 0 to 9, A to F.
XII
XIII
XIV
Press and hold ENTER .
● If a security code is entered and the
unit verifies that it is correct, the
security function will be canceled.
XV
XVI
XVII
XVIII
XIX
157
ESN security operating procedure
ESN security operating procedure
Canceling the security function using a “Memory Stick Duo”
Press FUNC for less than 1 second.
Touch SEC .
● The security setting screen will appear.
Touch CANCEL .
● The security code entry screen will
appear.
Press FUNC .
Insert the “Memory Stick Duo”.
● The recorded data will be read from the “Memory Stick Duo”.
If the contents recorded in the “Memory Stick Duo” match the information
recorded by the unit, “The security lock was unlocked.” will appear on the
display.
● The security function will be canceled and the deck will return to normal operation.
Eject the “Memory Stick Duo”.
● Refer to “How to eject disc (CD/DVD) or “Memory Stick Duo”” on page 48.
●If the security code that is entered does not match the code that is recorded by
the unit, “ERROR” will appear on the display for 2 seconds and operation will
continue as normal without the security function being canceled.
●If a “Memory Stick” has already been inserted, a “MS EJECT” message appears.
In this case, eject the “Memory Stick Duo” and insert it again. (Refer to “How to
eject disc (CD/DVD) or “Memory Stick Duo”” on page 48 for details on ejection of
the “Memory Stick Duo”.)
●If a reading error occurs or if an incorrect “Memory Stick Duo” is inserted,
“ERROR” will appear on the display for 2 seconds, and then the display will
change to “EJECT”. If this happens, eject the “Memory Stick Duo” and try again.
●Security setting cannot be canceled by this procedure if the “Memory Stick Duo”
containing the security code is formatted.
158
How to change the “Memory Stick Duo”
You can change the “Memory Stick Duo” and security code that have been recorded by the
unit to a different “Memory Stick Duo” and security code.
Cancel the security code that has been recorded with the deck.
● Refer to “How to cancel the “Memory Stick” security” on page 157.
Re-record the new “Memory Stick Duo” and security code that you would
like to use.
● Refer to “How to record a security code” on page 155.
How to resume normal operation (ESN security lock out)
If power is disconnected while ESN security is active (a security code was recorded),
operation is disabled until power is restored and the unit unlocked. Follow this procedure to
resume normal operation.
ESN security lock can be canceled by directly entering the security code into the unit, or by
using the “Memory Stick Duo” that was being used when the security code was recorded.
Canceling ESN security lock out using security code entry
When the power is turned on after disconnecting the battery power, a
“SECURITY” message will appear for 2 seconds. Thereafter, the security
code entry screen will appear.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
A security code is entered by
touching switches.
XIII
● Enter a four-digit security code using
digits 0 to 9, A to F.
XIV
XV
XVI
XVII
XVIII
XIX
159
ESN security operating procedure
ESN security operating procedure
Press and hold ENTER .
● If the security code matches the code
recorded by the unit, “Security lock was
unlocked.” will appear on the display
and the security function will be
canceled.
Canceling ESN security lock using “Memory Stick Duo”
After the battery is connected and the unit’s power is turned on,
“SECURITY” will appear on the display for 2 seconds. After this, the
security code entry screen will appear.
Press FUNC .
Insert the “Memory Stick Duo” that has been recorded, and then close the
front panel.
● The recorded data will be read from the “Memory Stick Duo”.
160
If the contents recorded in the “Memory Stick Duo” match the information
recorded by the deck, “Security lock was unlocked.” will appear on the
display for 2 seconds, and then the deck will return to normal operation.
I
II
III
IV
V
VI
VII
VIII
IX
X
●If the security code does not match the information recorded by the unit,
“ERROR_” (ERROR and the error number) will appear on the display for two
seconds, and then “- - - -” (security code entry display) will appear. If this
happens, check the security code and repeat the procedure from step 2.
●If “ERROR5” (the 5th time an error has occurred) appears, “HELP” will appear.
When “HELP” appears, carry out the operations for an ESN security lock out by
following the procedure in “What happens if a “Memory Stick Duo” or security
code is incorrect?” on next page.
●If a “Memory Stick” has already been inserted, a “MS EJECT” message appears.
In this case, eject the “Memory Stick” and insert it again. (Refer to “How to eject
disc (CD/DVD) or “Memory Stick Duo”” on page 48 for details on ejection of the
“Memory Stick Duo”.)
●If the contents recorded in the “Memory Stick Duo” do not match the information
recorded by the unit, “ERROR_” (ERROR and the error number) will appear on
the display for 2 seconds, and then “- - - -” (security code entry display) will
appear. If this happens, check the “Memory Stick” and repeat the procedure from
step 2.
●ESN security lock cannot be canceled by this procedure if the “Memory Stick
Duo” containing the security code was formatted.
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
161
ESN security operating procedure
ESN security operating procedure
What happens if a “Memory Stick Duo” or security code is incorrect?
After the 5th incorrect attempt, the display reads “HELP” for 5 seconds.
● After the “HELP” message was displayed for 5 seconds, the serial number will appear.
You will only get 5 unsuccessful unlock code entries. After the 5th attempt, you will be
asked to insert the DISC (Key CD). At this point, please contact your local Eclipse
dealer or Eclipse Customer Service for procedure on unlocking the unit.
For country-specific customer service information, refer to “How to contact
customer service” on page 245.
Your security code and “Memory Stick Duo” can be easily forgotten. Write the
security code and “Memory Stick Duo” title in a reminder note.
162
How to operate the ACC security
ACC security involves using “Memory Stick” security to record a security code, and then when
the ignition switch is turned to OFF and back to ACC, the operation of all buttons is disabled.
I
Press FUNC for less than 1 second.
II
Touch SEC .
III
● The security setting screen will appear.
Touch ACC .
● Touching the this switch toggles
between ON and OFF.
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
●If the vehicle's battery is disconnected at times such as during servicing, ACC
security will be canceled.
●When ignition switch is turned OFF and back to ACC, the operation all button is
disabled. If this happen, resume normal operation. (Refer to “How to resume
normal operation (ESN security lock out)” on page 159.)
XVIII
XIX
163
ESN security operating procedure
ESN security operating procedure
How to turn the security indicator on/off
Once ESN security is activated, the indicator flashes whenever the vehicle's ignition switch is
turned off, warning potential thieves that the unit is protected. However, if do not want this
visible deterrent, it may be turned off.
Press FUNC for less than 1
second.
Touch SEC .
● The security setting screen will appear.
Touch INDICATOR .
● Touching the this switch toggles
between ON and OFF.
“ON” means the security indicator will flash when the vehicle's ignition switch is off, and
“OFF” means it will not.
Repeat the above steps to reactivate the flash mode.
How to read the Electronic Serial Number
Press FUNC for less than 1 second.
Touch SEC .
● The security setting screen will appear.
● An 8-digit number appears on display.
164
How to use the remote control
Before using remote control
●Be sure to properly store the remote control when not in use. An improperly
stored remote control could shift during braking or cornering and interfere with
driving operation (for example, by becoming lodged under the brake pedal) and
cause an accident.
●Do not expose the remote control to extreme heat or direct sunlight, especially
when it is in the vehicle. Doing so could cause a fire.
Precautions when using the remote control
●Be careful when handling the remote control, especially because it is small and
light. Dropping or striking it may damage it, wear out the battery or cause a
malfunction.
●Keep the remote control free of moisture, dust and water. Do not subject it to
shock.
●Do not place the remote control unit where it will get hot, such as on the
dashboard or near a heater vent. Allowing the remote control unit to overheat
may warp its case or cause other problems.
●Do not operate the remote control unit while driving because doing so could
cause an accident.
●When using the remote control, point it directly at the remote control light
receptor.
●The light receptor may not operate correctly if it is exposed to bright light such as
direct sunlight.
●Remove the batteries from the remote control unit whenever it is not to be used
for a long time.
●Store the remote control away from direct sunlight, extreme heat, and high
pressure. Exposure to these elements could result in warping of the casing,
battery rupture, or battery leakage.
Cleaning the remote control
●Use a dry cloth to keep the unit clean. If the remote control unit gets extremely
dirty, clean it with a cloth moistened in a diluted liquid detergent. Do not use
alcohol or thinner; these compounds may damage the finish.
●In no event should benzine or thinner be used. These substances will damage
the case or finish.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
165
How to use the remote control
How to use the remote control
PWR
button
MODE
MUTE
button
button
Remote-Control
light receptor
button
button
Turning the power on/off
When the power is turned on, the last mode prior to turning off the power such as CD and
tuner playing is restored.
Press PWR .
● The power turns on or off each time the button is pressed.
Adjusting the audio volume
Press
●
or
.
button: Increases the volume.
button: Decreases the volume.
Muting the volume
Press MUTE to cut or mute the volume or restore it instantly.
Switching playback modes
Press MODE .
● Tap the button to switch modes in the following sequence:
Tuner
166
DVD (CD)
CDCH
VTR
BAND
button
I
II
III
IV
V
How to select the tuner
VI
Select the tuner mode first.
VII
Selecting the FM/AM band
VIII
Press the BAND .
● Each tap will switch tuner modes from FM1
FM2
FM3
AM.
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
167
How to use the remote control
How to use the remote control
MODE
button
BAND
button
How to play back CDs
Select the disc mode first.
Switching disc modes
Press the MODE button to switch DVD (CD) player or CD changer.
When two CD changers are connected, press the BAND button to change
between CD changer 1 and CD changer 2.
168
Replacing the battery
To prevent accidents, store batteries out of the reach of children. If a child has
swallowed one, consult a doctor immediately.
Use two AA-size batteries.
Remove the back cover of the remote control by
gently pressing and sliding it in the direction
indicated by the arrow.
I
II
III
IV
V
VI
Install the two batteries provided into the
compartment as illustrated inside the
compartment.
VII
VIII
IX
X
Return the back cover into place by sliding it in
the direction indicated by the arrow.
XI
XII
XIII
XIV
XV
●Be extremely careful not to swallow the battery.
●The battery life is approximately one year. If the remote control unit does not
operate correctly or if the button lamp gets dim, replace the batteries.
●Be sure to orient the batteries correctly so that the positive and negative poles
match the diagram.
●Do not use one new battery and one old one; use two new batteries.
●Use only two of the same kind of battery.
●If any liquid is seen leaking from the batteries, remove both batteries and
dispose of them properly. Thoroughly clean the battery compartment with a dry
cloth. Then install new batteries.
XVI
XVII
XVIII
XIX
169
How to operate the optional 5.1ch decoder & AV selector unit
Sound quality information
Functions of the optional 5.1 ch decoder & AV
selector unit is connected
The following table shows the finer audio adjustments that can be performed when the
optional 5.1 ch decoder & AV selector unit is connected.
Item
Function
Page
Parametric EQ
Perform a 5-band parametric equalizer adjustment on each
channel (front, rear, center) and a 1-band adjustment on
the woofer for a total of a 16-band adjustment.
178
Sound localization can be adjusted according to the
number and position of passengers in order to obtain
optimum acoustic effects.
183
POSITION
FADER/BALANCE
Speaker
Settings
Surround
System
Settings
170
The left/right/front/rear balance can be adjusted.
184
Time
Alighnment
The delay time and level of the sound from each speaker
can be adjusted in order to correct any phase mismatches
in the sound resulting from the listening position.
189
Crossover
Allocate specified frequency bands to each speaker for
improved sound integration.
191
Non-fader
level
When a sub-woofer is connected, the preferred output
level for the audio can be set.
193
Non-fader
phase
The merging of sound between the front and rear speakers
and the sub-woofer can be improved by selecting the
phase. Switch to a phase which lets the speakers combine
without any disharmony.
194
Speaker
Level
Adjust the frequency band output to fit the size of the
speakers connected to the unit.
195
Speaker
Size
Set the speaker size.
196
Dolby Pro
Logic II
Achieve surround sound by moving from 2 channel stereo
to 5.1 channel sound.
186
COMPRES
SION
Set the dynamic range (difference between the lowest and
highest audio signal).
188
Center
Width
When Dolby Pro Logic II is set to Music and the center
speaker is set to LARGE or SMALL, sound from the center
speaker is distributed to the left and right front speakers.
187
Center
Level
Adjust the output level of the center speaker.
187
Rear Level
Adjust the output level of the rear speakers.
187
Item
Function
Page
When original sounds are converted to a MP3/WMA
format, frequency ranges that are not normally audible to
the human ear are compressed. The harmonizer can be
used to play back these compressed sounds at as close to
their original form as possible so that clear and powerful
sound can be enjoyed.
185
Loudness
The loudness control may be turned on the emphasize low
and high frequencies at low volume levels. Loudness
compensates for the apparent weakness of low and high
frequencies at low volume by boosting the bass and treble
levels.
185
E-iSERV Sound Effect
Customizations
Download sound adjustment data from the ECLIPSE
website (E-iSERV) that matches the vehicle's interior and
store it in the unit.
175
Harmonizer
I
II
III
IV
V
VI
About parametric EQ
VII
A variety of materials are used inside a vehicle to manufacture the seats and windows, and
because these materials absorb and reflect sound in different ways, the parametric equalizer
lets you adjust the peaks and dips of the frequency characteristics inside the vehicle to
compensate for this.
VIII
Peak
High
IX
X
XI
[Sound pressure]
Dip
Low
Low
[Frequency]
High
An “equalizer” is a function that corrects these peaks and dips in order to flatten the frequency
characteristics. However with a normal graphic equalizer, the median frequency and the Q
(sharpness and band width) are fixed, so that when neighboring bands are corrected, there is
a limit to the amount by which distortion in the peak and dip characteristics can be corrected.
A “parametric equalizer” lets you adjust the median frequency, Q (sharpness and band width)
and gain to variable levels, so that you can make fine adjustments to spot areas of the
frequency band.
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
171
How to operate the optional 5.1ch decoder & AV selector unit
Sound quality information
[Parametric equalizer characteristics]
1. Median frequency can be varied.
High
[Sound pressure]
Low
Low
[Frequency]
High
Low
[Frequency]
High
[Frequency]
High
2. Gain can be varied.
High
[Sound pressure]
Low
3. Q (sharpness/band width) can be varied.
High
[Sound pressure]
Low
Low
172
About time alignment
With vehicle audio systems, the installation position of the speakers and the position of the
listener mean that the distances from the listener to the left and right speakers are almost
always different. These differences in the distance from the listener to each speaker in turn
means that the time taken for the sound to reach the listener is different for each speaker. The
result of this is that the phases of each speaker (biases) become mismatched and the sound
becomes unnatural, as though the sound stage is not wide enough. The “time alignment”
function corrects the time taken for the sound waves to reach the listener in order to set the
optimum phase for the listening position so that the sound becomes more expansive as
though it is being listened to from a sound stage.
The basic adjustment method involves measuring the actual distances to each speaker and
calculating the differences in distance relative to the most distant speaker in order to derive
the delay time for the sound from each speaker.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
173
How to operate the optional 5.1ch decoder & AV selector unit
Sound quality information
About crossover
The frequency band that is stored by audio media such as CDs is a fairly wide range from 20
Hz to 20 kHz, and it is difficult for a single speaker to be able to play back all frequencies in
such a wide range.
Because of this, several speakers can be used, with different frequency bands (such as treble,
medium and bass) allotted to each speaker so that wide frequency ranges can be played
back. The “Crossover” function is used to allot the frequency ranges that are to be played back
by each speaker in accordance to the installed speaker units and the layout of the speakers, in
order to obtain the maximum level of performance from the speakers and to provide the most
stable frequency characteristics.
The crossover function includes a high-pass filter (HPF) for playing back treble sounds, and a
low-pass filter (LPF) for playing back bass sounds. In addition, the HPF and LPF are used in
combination in order to play back sounds in the mid range.
-3dB
Bass range
20Hz
Mid range
fc1(LPF)
fc2(HPF)
Treble range
fc3(LPF)
fc4(HPF)
20kHz
fc*: Cutoff frequency
For example, when adjusting the HPF, frequencies that are lower than the specified frequency
are progressively dampened, rather than simply not being played back at all. The “slope”
adjustment function is the function that is used to adjust these dampening characteristics.
The slope characteristics of a filter are such that with larger slope values (for example 12 dB/
oct), the slope becomes steeper, and so the amount of sound mixing in with neighboring
bands becomes less so that only the target band is played back. However, it also causes the
merging of sound between speakers to become poorer and can result in greater distortion.
● The crossover function is a filter that allocates specified frequency bands.
● A high-pass filter (HPF) is a filter that cuts out frequencies that are lower than the specified
frequency (bass range) and allows higher frequencies (treble range) to pass through.
● A low-pass filter (LPF) is a filter that cuts out frequencies that are higher than the specified
frequency (treble range) and allows lower frequencies (bass range) to pass through.
● The slope is the signal level at which frequencies that are one octave higher or one octave
lower are dampened.
The larger the slope value, the greater the slope. In addition, when “PASS” is selected, the
slope is eliminated (sound does not pass through the filters), so that the crossover function
has no effect.
174
About E-iSERV sound effect customizations
The parametric equalizer, time alignment and crossover setting can be adjusted using this
unit, or through the E-iSERV (web site).
About automatic parametic equalizer
This can be used to automatically correct distortion in frequency characteristics (peaks and
dips) based on the results of measuring the frequency characteristics inside the vehicle.
Automatic parametric equalizer correction is carried out in the following steps.
Speakers adjustment
(Refer to “Setting/Adjusting speakers” on page 189.)
I
II
III
IV
V
VI
Frequency characteristics mearurement
Saving sound data
After measureing frequency characteristics, sound data will be
written to “Memory Stick Duo” automatically.
(Refer to “Measuring/Displaying frequency characteristics” on
page 182.)
E-iSERV (web site) accesing
Access the following URL: http://www.e-iserv.jp
Register as a user. A ePID (User Registration Key) is required when registering. For
details for “Displaying ePID” on page 137.
(To register, follow the instructions provided by the website. Once you have
registered, there is no need to repeat the procedure.)
Login.
Automatic parametric equalizer adjustment
Follow the instructions given on the web site.
Correction data downloading
Follow the instructions given on the web site.
Correction data reading
(Refer to “Importing sound data” on page 198.)
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
175
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Displaying the sound adjustment screen
Press SOUND .
● The sound adjustment screen will
appear.
● Touch any of the following buttons on
the sound adjustment screen to display
the corresponding adjustment screen.
● Sound adjustment screen
● Parametric equalizer adjustment screen
PEQ
● Position setting screen
POS
● Setting screen
SETTING
176
● Setting screen
● Speaker Level setting screen
SP Level
I
II
● Time alignment adjustment screen
III
IV
Time Alignment
V
VI
● X-over setting screen
VII
VIII
X-Over
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
177
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Adjusting PEQ (Parametric equalizer)
If the optional 5.1 ch AV selector unit is connected, the parametric equalizer can be used for a
5-band adjustment of each of the front, center, and rear channels, and a 1-band adjustment of
the woofer for a total of a 16-band adjustment. Each band can be set to the following median
frequencies:
Channel
Front
Center
Rear
WOOFER
Band
Adjustable frequency (Hz)
1 to 5
20, 25, 31.5, 40, 50, 100, 125, 160, 200, 250, 315, 400,
500, 630, 800, 1k, 1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k, 5k, 6.3k,
8k, 10k, 12.5k, 16k, 20k
1
20, 25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250
Each band is initially set to the following median frequency:
● Front, Rear and Center channel
Band1: 100 Hz
Band2: 200 Hz
Band3: 400 Hz
Band4: 800 Hz
Band5: 1.6 kHz
● WOOFER channel
63 Hz
It is not possible to set more than one band in the same channel and median
frequency. Either change the median frequency of the current band, or change the
median frequency of another band.
178
Adjusting/Saving a PEQ
Touch PEQ in the sound
adjustment screen.
Touch ch to select the channel to
be adjusted.
● Each time the switch is touched, the
channel will be changed in the
following order shown below.
Front
Rear
Center
Woofer
I
II
III
IV
V
VI
Touch BAND to select the band to
be adjusted.
VII
● Each time the switch is touched, the
band will be changed in the following
order shown below.
VIII
Band1
Band2
Band5
Band3
Band4
IX
X
XI
Touch
or
for Freq to select
the frequency to be adjusted.
XII
●
XIII
: Increase frequency
: Decrease frequency
Touch
or
for Level to
adjust the frequency lelvel.
●
: Increase level
: Decrease level
XIV
XV
XVI
XVII
XVIII
XIX
179
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Touch Q to select the Q curve
pattern.
● Each time this switch is touched, Q
curve pattern will be changed in the
following order shown below.
SHARP
MIDDLE
SHARP
NORMAL
Repeat the operations in step
to
to change the setting for each
channel and band.
Press and hold the switch you want
to use to save ( 1 to 5 ) until
you hear a beep.
● Save the PEQ setting so they can be
used for other settings.
● Touch BACK after making settings.
The PEQ mode adjustments will be
saved and system will return to the
previous operation screen.
180
MIDDLE
SLOW
SLOW
Selecting a PEQ pattern from memory
Touch 1 to 5 .
● The preset pattern stored in memory
will be retrieved.
● Touch BACK after making settings.
The PEQ mode adjustments will be
saved and system will return to the
previous operation screen.
Measuring/Displaying frequency characteristics
Frequency characteristics inside the vehicle can be measured and displayed on the display.
The measurement result can be referred to when adjusting parametric equalizer. This is also
necessary to automatically correct parametric equalizer setting using E-iSERV sound effect
customizations.
Connect the accessory
microphone with an optional 5.1ch
decoder & AV selector unit.
● Align the microphone with the actual
ear position and attach it to the
headrest or another appropriate fixture.
(Attach the microphone using tape or
string.)
To avoid writing measurement results to the “Memory Stick Duo”
Touch Measure for less than 1
second.
● After touching the switch, a 10-second
count down begins. Leave the vehicle
during that time.
● Pink noise will be outputted from the
speakers and measurement of the
frequency characteristics will start.
● When measurement is complete, the
measurement results of the front
channel will appear on the display.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
181
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
● Touch STOP to cancel measurement.
To write measurement results to a “Memory Stick Duo”
Insert the “Memory Stick Duo”.
Press and hold the Measure
switch until you hear a beep.
● After touching the switch, a 10-second
count down begins. Leave the vehicle
during that time.
● Pink noise will be outputted from the
speakers and measurement of the
frequency characteristics will start.
● When measurement is complete, the
measurement results of the front
channel will appear on the display.
● Measurements can be written to a
“Memory Stick Duo” and corrected
automatically using E-iSERV web site.
● Touch STOP to cancel
measurement.
Slight errors may occur in the measurement data under some circumstances when
this function is used. In addition, it is not equivalent to the precise measurements
that can be made by professional measuring devices.
●Close all doors and windows while measurement is in progress.
●Sound quality data is written to “Memory Stick Duo” as follows.
MSFTEN
SOUND
105*000.ftn
File extension
Three digit number
Adjustment mode
●The folders and files that are required for E-iSERV sound effect customizations
are created automatically when the data is written to the “Memory Stick Duo”.
●Select a file in MSFTEN SOUND when uploading sound quality data to the E-iSERV
(web site).
182
Adjusting POS (Positioning selector)
Sound localization can be adjusted according to the number and position of passengers in
order to obtain optimum acoustic effects.
A seat's sound localization can be adjusted simply by touching the switch.
I
II
Touch POS in the sound
adjustment screen.
III
IV
Touch each seat image displayed
in the POSITION setting screen to
switch the sound localization for
that seat.
V
VI
● The selected position will appear in a
green frame. Touch the seat again to
cancel the selection. The four positions
shown by the table below can be set.
VII
VIII
● Touch OFF to cancel all settings.
● Touch BACK after making settings.
The position will be saved and the
system will return to the previous
operation screen.
IX
X
XI
Touch switch
Function
Touch switch
Function
Acoustics optimized for
driver's seat
Acoustics optimized for
both front seats
Acoustics optimized for
passenger's seat
Acoustics optimized for
rear seats
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
If the positioning selector has been set (to a setting other OFF), the FAD/BAL
(Fader/Balance) settings cancelled (next page).
183
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Setting the balance
The left/right/front/rear balance can be adjusted so that sound from all speakers arrives at the
listener's ears at the same time.
Touch FAD/BAL in the POSITION
setting screen to display the
volume balance adjustment
screen.
Touch
,
,
or
.
● The adjustment level can be set to one
of 15 levels between F (front) and R
(rear).
● The adjustment level can be set to one
of 15 levels between L (left) and R
(right).
● Touch CENTER to set the volume
balance to the center position.
● Touch BACK after making settings.
The set volume balance will be saved
and the system will return to the
previous operation screen.
● To set the position again, touch POS
and repeat the steps above.
●If the balance has been set (to a setting other CENTER), the positioning selector
setting will be cancelled (previous page).
,
,
or
while making fine adjustments to adjust
●Touch and hold
values continuously. Adjustment will lock when it reaches the center value, and
,
,
or
must be touched again to continue adjustment.
184
Setting LOUDNESS
Audio can be modulated to correct for insufficient bass and treble when listening at low
volume.
I
Touch LOUDNESS .
II
● Touching the switch toggles between
ON and OFF.
III
IV
V
Setting the harmonizer
It is possible to set the sound quality boost level to automatically regenerate harmonics such
as reverberation, depth, and tone lost in compression, producing a much clearer sound.
VI
VII
VIII
Touch Harmonizer .
IX
● Each touch the switch is touched, the
Harmonizer setting will be changed in
the following order shown below.
X
Low
Hi
OFF
XI
XII
● LOW : Low level of correction
HI : High level of correction
OFF : No correction
XIII
XIV
XV
XVI
XVII
XVIII
XIX
185
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Setting/Adjusting surround system
Dolby Digital (5.1 ch), DTS (5.1ch), LPCM, and Dolby Pro Logic are supported when the
optional 5.1 ch AV selector unit is connected. Playing discs recorded using these technologies
allows the listener to enjoy theater-quality sound within a limited space.
Setting the Dolby Pro Logic II
Dolby Pro Logic II expands sound recorded in stereo (2 ch) for a rich listening experience.
Different modes may be selected for different media types.
Touch SETTING in the sound
adjustment screen.
Touch Dolby Pro Logic II in the
setting screen.
● Each time the switch is touched, the
modes will be changed in the following
order shown below.
Movie
Music
4chST
OFF
● Touch BACK after making settings.
The time setting mode adjustments will
be saved and system will return to the
previous operation screen.
Item
Movie
Select when playing a DVD or VTR recorded in stereo (2
ch).
Music
Select when playing an audio CD.
4ch ST
Select when stereo (2ch) sound is played through 4
speakers (4 ch).
OFF
186
Effectiveness
Turns Dolby Pro Logic II OFF.
Setting the Center Level
Adjusts the dialog and music output level heard from center speaker.
Touch
or
for Center Level.
● The center level can be adjusted within
-10 to 10 (in units of 1 step).
: Increase the level.
: Decrease the level.
I
II
III
IV
V
Setting the Rear Level
Adjusts the dialog and music output level heard from rear speaker.
Touch
or
for Rear Level.
● The rear level can be adjusted within 10 to 10 (in units of 1 step).
: Increase the level.
: Decrease the level.
VI
VII
VIII
IX
X
XI
XII
Setting the Center Width
When Dolby Pro Logic II is set to Music and the center speaker is set to LARGE or SMALL,
sound from the center speaker is distributed to the left and right front speakers.
Touch
or
for Center Width.
● The center width level can be adjusted
within 0 to 7 (in units of 1 step).
: Increase the level.
: Decrease the level.
XIII
XIV
XV
XVI
XVII
XVIII
XIX
187
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Setting the Compression
Adjusts the sound sensation range (difference between maximum and minimum when playing
a DVD with Dolby Digital (5.1 ch) or DTS (5.1 ch). Raising the numerical value of the
compression level will narrow the sound range so that dialog and voice will be easier to hear
even when background sounds are intense.
Touch SETTING in the sound
adjustment screen.
Touch Compression in the
setting screen.
● Each time this switch is touched,
compression setting will be changed in
the following order shown below.
0
1
2
8
3
7
4
5
6
● Touch BACK after making settings.
The compression setting mode
adjustments will be saved and system
will return to the previous operation
screen.
Adjustment Level
0
1 to 7
8
188
Function
Compression function effect is off.
Compression function effect can be adjusted in a middle
range.
Compression function effect is at maximum.
Setting/Adjusting speakers
Settings and adjustments can be made to fit the speakers connected to the unit.
The following settings and adjustments can be performed when the optional 5.1 ch AV
selector unit is connected.
● Time alignment
I
II
● X-Over
III
● Speaker size
IV
● Speaker level
V
Adjusting time alignment
The delay time and level of the sound from each speaker can be adjusted in order to correct
any phase mismatches in the sound resulting from the listening position.
In addition, the optional 5.1 AV selector unit has a function for automatically correcting time
alignment.
Manual adjustment
Touch SETTING in the sound
adjustment screen.
Touch Time Alignment in the
setting screen.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
189
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Touch
or
for each speaker
to adjust the delay time.
● The delay time can be adjusted within
0.0 to 10.0 ms (in units of 0.1 ms).
: Increase the time
: Decrease the time
● Touch BACK after making settings.
The time alignment mode adjustments
will be saved and system will return to
the previous operation screen.
●Refer to the following for the method of calculating the delay time.
A=(B-C)/34
A: Delay time (ms)
B: Distance from listening position to furthest speaker (cm)
C: Distance from listening position to the speaker to be adjusted (cm)
C
B
<Example>
Listening position: Driver's seat (left)
B: 200 (cm)
C: 50 (cm)
Delay time=[200 (cm) - 50 (cm)]/34 =Approx. 4.4 ms
190
Automatic adjustment
Connect the microphone
accessory with an optional 5.1ch
decoder & AV selector unit.
● Align the microphone with the actual
ear position and attach it to the
headrest or another appropriate fixture.
(Attach the microphone using tape or
string.)
I
II
III
IV
V
Touch AUTO .
● After touching the switch, a 10-second
count down begins. Leave the vehicle
during that time.
● Pink noise will be outputted from the
speakers and setting of the time
alignment will start.
● Touch STOP to cancel setting.
● Touch BACK after making settings.
The time alignment mode adjustments
will be saved and system will return to
the previous operation screen.
Adjusting X-Over
Allocate specified frequency bands to each speaker for improved sound integration.
Touch SETTING in the sound
adjustment screen.
Touch X-Over in the setting
screen.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
191
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Touch Front , Center , Rear ,
or Woofer to select the speaker
to be adjusted.
Touch Freq to select the cut-off
frequency.
● Each time this switch is touched, the
cut-off frequency will be changed in the
following order shown below.
Front/Center/ Rear (Hz):
100
125
160
200
250
315
400
500
630
800
1k
1.25k
1.6k
2k
2.5k
3.15k
4k
5k
6.3k
8k
10k
12.5k
16k
20k
Woofer (Hz):
20
25
31.5
40
50
80
100
125
160
250
63
200
Touch SLOPE to select the
slope.
● Each time this switch is touched, the
slope will be changed in the following
order shown below.
PASS
6 dB/oct
12 dB/oct
18 dB/oct
24 dB/oct
● Touch BACK after making settings.
The X-Over mode adjustments will be
saved and system will return to the
previous operation screen.
If no woofer has been connected, set the slope adjustment to “PASS”. (If slope is
set to a setting other than PASS, the low frequency range will not be outputted
from the speakers.
192
Adjusting sub-woofer output level
When a sub-woofer is connected, the preferred output level for the audio can be set.
Touch SETTING in the sound
adjustment screen.
Touch X-Over in the setting
screen.
I
II
III
IV
V
Touch
or
for level to adjust
the Woofer Level.
●
: Increase the level
: Decrease the level
● Touch BACK after making settings.
The sub-woofer output level mode
adjustments will be saved and system
will return to the previous operation
screen.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
193
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Setting phase control
The merging of sound between the front and rear speakers and the sub-woofer can be
improved by selecting the phase. Switch to a phase which lets the speakers combine without
any disharmony.
Touch SETTING in the sound
adjustment screen.
Touch X-Over in the setting
screen.
Touch Phase to select the
NORMAL or REVERSE.
● Touch BACK after making settings.
The phase control adjustments will be
saved and system will return to the
previous operation screen.
194
Adjusting speaker level
Touch SETTING in the sound
adjustment screen.
Touch SP LEVEL in the setting
screen.
I
II
III
IV
Touch
or
for each speaker
to adjust the speaker level.
V
● The speaker level can be adjusted
within -10 to 10 dB (in units of 0.1 dB).
VI
: Increase the level.
: Decrease the level.
● Touch BACK after making settings.
The speaker level mode adjustments
will be saved and system will return to
the previous operation screen.
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
195
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Adjusting speaker size
Touch SETTING in the sound
adjustment screen.
Touch SP LEVEL in the setting
screen.
Touch Center , Front , Rear ,
and Woofer to set the speaker
size.
● Each time this switch is touched, the
speaker size will be changed in the
following order shown below.
Center/Rear:
LARGE
SMALL
Front:
LARGE
Woofer:
Yes
No
196
SMALL
NONE
■Speaker settings and functions
Speaker
Center
Size
Function
NONE
Distributes output to the center speaker to the front left and
right speakers.
SMALL
This setting is used when the speakers connected to the
unit are unable to output frequencies lower than 100Hz.
(Frequencies lower than 100 Hz will not be output.)
LARGE
This setting is used when the speakers connected to the
unit are able to output frequencies lower than 100 Hz.
III
SMALL
This setting is used when the speakers connected to the
unit are unable to output frequencies lower than 100 Hz.
(Frequencies lower than 100 Hz will not be output.)
IV
LARGE
This setting is used when the speakers connected to the
unit are able to output frequencies lower than 100Hz.
NONE
Distributes output to the center speaker to the front left and
right speakers.
SMALL
This setting is used when the speakers connected to the
unit are unable to output frequencies lower than 100 Hz.
(Frequencies lower than 100 Hz will not be output.)
VIII
LARGE
This setting is used when the speakers connected to the
unit are able to output frequencies lower than 100 Hz.
IX
YES
Outputs sound from the sub-woofer.
NO
Does not output sound from the sub-woofer.
X
Front
Rear
Woofer
I
II
V
VI
VII
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
197
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
Importing sound data
Sound data adjusted by the E-iSERV (web site) can be downloaded to a “Memory Stick Duo”
and imported into the unit.
Insert the “Memory Stick Duo” to
be used for the sound data.
Press FUNC to display the FUNC
screen.
Touch DATA .
Touch SOUND .
Touch the file name to select the
correct file.
● Touch
198
,
to move the list.
Touch DATA READ .
I
II
III
Select a preset switch 1 through
5 .
IV
● Sound data will be recorded for the
selected switch.
V
● Touch the Cancel to cancel data
saving.
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
199
How to operate the optional 5.1ch decoder & AV selector unit
Adjusting sound quality
● If the selected switch already contains
stored data, a message will be
displayed.
● Select Yes to overwrite the data.
Do not turn the power or ignition switch off while reading. Interrupting the reading
process may corrupt the data.
●Data downloaded from the E-iSERV (web site) is saved to folders created in the
“Memory Stick Duo” as shown below.
MSFTEN
User creation
DATA
105 X 00 .eis
Automatic creation
File extension
Two digit number
Adjustment pattern
a: Flat tuning B: Bass range emphasis
c: Bass and Treble range emphasis
d: Midium range emphasis
0: No automatic parametric equalizer correction
Adjustment mode
●Files that can be imported into your unit are created automatically when
downloaded from E-iSERV (web site)
200
How to operate the optional 5.1ch decoder & AV selector unit
Setting display
Screen settings of the optional 5.1 ch decoder & AV
selector unit
Up to two external monitors can be connected when the 5.1 ch decoder & AV selector unit is
connected. Separate images can be displayed on each external monitor.
External monitor image settings
Select the image to be displayed on the external monitors.
Press and hold FUNC until you
hear a beep.
Touch AV Setting .
I
II
III
IV
V
VI
VII
VIII
Touch Monitor 1 or Monitor 2
and select an image.
● Each time the switch is touched, the
image is changed in the following order
shown below.
DVD
VTR1
VTR2
● The selected image will appear on the
left side of the screen.
● Touch BACK after making settings.
The picture setting mode adjustments
will be saved and system will return to
the previous operation screen.
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
If a VTR or DVD player is not connected to the 5.1 ch decoder & AV selector unit,
no image will be displayed.
201
How to operate the optional HD radio tuner (U.S.A. only)
How to use the HD radio
BAND switch
Preset switches
FUNCTION switch
• ASM
• Info
MENU
button
POWER
button
SOURCE
button
TUNE·TRACK
button
About HD Radio
If the optional HD Radio (High Definition Radio) tuner unit is connected, terrestrial digital
broadcasts can be received. When terrestrial digital broadcasts are received, FM reception
has the same quality as a CD, and AM reception has the same quality as conventional FM
sound. Depending on the reception status, HD Radio can also receive analog broadcasts,
which means reception is still possible in regions with no digital coverage.
Listening to the HD radio
Listening to the HD radio using the touch switches
Press MENU .
Touch AM or FM .
Listening to the HD radio using the panel buttons
Touch SOURCE to select the AM or FM.
202
Switching the band
Touch BAND .
● Each time the switch is touched, the band will be changed in the following order shown
below.
HD (FM)
HD (FM2)
HD (FM3)
HD (AM)
Selecting radio stations
Manual selection
Press
or
.
● Pressing the switch once moves the frequency one step up or down.
●
(up) : Raises the frequency
(down) : Lowers the frequency
Automatic selection
Press and hold
or
until you hear a beep.
● The station that is closest to the current frequency will be searched for automatically,
and searching will stop when the station is received. To stop the search before a
station is found, press the button again.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
Selection when using preset switches
XIII
Touch a preset switch that already has a station recorded.
XIV
● See “Saving radio stations” on next page for more information.
XV
XVI
XVII
XVIII
XIX
If the reception for a particular station is weak in the area you are in, the automatic
selection may not work.
203
How to operate the optional HD radio tuner (U.S.A. only)
How to use the HD radio
Saving radio stations
There are two modes for saving radio stations, manual and ASM. These modes operate
independently.
Saving manually
Use manual tuning or automatic tuning to select the station to be saved.
Choose a preset switch and press and hold it until you hear a beep.
● The radio station (frequency) is set. Touch the preset switch to tune in the selected
station.
Saving with ASM
Touch FUNC .
Press and hold ASM until you hear 2 beeps in succession.
● The ASM function will activate and start automatically selecting stations. You will hear
a beep when the automatic selection of stations is completed. Touch ASM again to
switch the display back to the broadcast stations originally saved.
Changing stations saved by ASM
Use manual tuning or automatic tuning to select the station to be saved.
Press and hold the preferred preset switch until you hear a beep.
●ASM may not automatically receive stations if radio waves in the surrounding
area are weak.
●A frequency saved with the tuning switch may not match the frequency saved
with ASM even though the signal is received from the same station.
●Due to conditions for receiving radio waves, saved stations may differ even when
the ASM switch is operated repeatedly in the same location.
●Up to six stations with good signal reception are automatically saved in order of
frequency (low to high).
●When less than six stations capable of reception are found, nothing is saved for
the remaining preset switches.
204
Checking preset stations
This recalls all the stations that have been preset either automatically or manually and plays
them each for 5 seconds.
I
Touch FUNC .
II
Touch ASM touch switch for less
than 1 second.
III
● “P.SCAN” will be displayed, and the
preset stations will each be played
back for 5 seconds.
Touch ASM touch switch for less
than 1 second once more.
● The station that was being played
when the switch was touched will then
be played continuously.
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
205
How to operate the optional HD radio tuner (U.S.A. only)
How to use the HD radio
HD radio information screen display
Displays the HD radio station name and other information.
Touch FUNC .
● The function mode is activated.
Touch
Info
.
● The HD radio information screen will
appear.
206
HD radio reception settings
The HD radio reception method can be selected. When the HD Radio tuner is connected to
this deck for the first time, it will be set at “AUTO” (automatic digital/analog selection).
Touch FUNC .
● The function mode is activated.
Touch
Info
.
● The information mode is activated.
I
II
III
IV
V
VI
VII
Touch Mode .
● In the “AUTO” setting, the selection is
switched between digital and analog
reception automatically. In areas where
digital reception is not possible,
reception is automatically switched to
analog to avoid loss of reception.
During digital reception, “DIGITAL” is
shown on the display. “DIGITAL” will be
removed from the display during
analog reception.
● In the “OFF” setting, reception is
always analog.
VIII
IX
X
XI
XII
XIII
XIV
XV
Turning off the radio
Press
.
● Press
again to turn on the radio
and resume reception of the radio
station (frequency) received before
power was turned off.
XVI
XVII
XVIII
XIX
207
How to operate the optional SIRIUS satellite radio tuner (U.S.A. only)
How to use the SIRIUS satellite radio
BAND switch
Preset switches
FUNCTION switch
• CAT
• Direct
• Info
MENU
button
POWER
button
SOURCE
button
TUNE·TRACK
button
About SIRIUS satellite radio
If the optional SIRIUS satellite radio tuner unit is connected, satellite radio broadcast can
be received.
With SIRIUS satellite radio, over 100 channels are available including music, sports,
news, and entertainment programs.
A channel can be selected from categories such as POP and ROCK, or by selecting
individual channels manually.
Reception of SIRIUS satellite radio is fee based; you have to subscribe to it.
It is possible to subscribe through the SIRIUS radio website.
URL: http://cdn.sirius.com
208
Listening to the SIRIUS satellite radio
Listening to SIRIUS satellite radio using the touch switches
I
Press MENU .
II
Touch SIRIUS .
III
Listening to SIRIUS satellite radio using the panel buttons
Press SOURCE to select the SIRIUS mode.
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
For information about the operation and set-up of the SIRIUS satellite radio tuner
unit, see the SIRIUS satellite radio unit's owner's manual.
209
How to operate the optional SIRIUS satellite radio tuner (U.S.A. only)
How to use the SIRIUS satellite radio
Selecting SIRIUS channels
Manual selection
Press
or
.
● Pressing the switch once moves the channel one step up or down.
●
(up) : Raises the channel
(down) : Lowers the channel
Automatic selection
Press and hold
or
until you hear a beep.
● The station that is closest to the current frequency will be searched for automatically,
and searching will stop when the station is received. To stop the search before a
station is found, press the button again.
Selection using preset switches
Touch a preset switch that already has a channel recorded.
● See “Saving SIRIUS channels” on next page for more information.
If the reception for a particular station is weak in the area you are in, the automatic
selection may not work.
210
Category selection
The channel can be selected from among categories such as POP and ROCK.
Consult the SIRIUS website for details of categories.
Touch FUNC .
I
II
III
IV
V
Touch Category .
● The category selection screen will
appear.
VI
VII
VIII
IX
X
Touch a category.
● Touch NEXT to switch to the next
screen.
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
211
How to operate the optional SIRIUS satellite radio tuner (U.S.A. only)
How to use the SIRIUS satellite radio
Direct Channel selection
The channel can be selected by inputting the channel directly.
Touch FUNC .
● The function mode is activated.
Touch Direct .
● The direct channel selection screen will
appear
Enter the number of the desired
channel.
● Touch CLEAR to delete one
number at a time.
Touch ENTER .
212
Saving SIRIUS channels
Use manual tuning or automatic tuning to select the channel to be saved.
Choose a preset switch and press and hold it until you hear a beep.
● The radio SIRIUS channel is set. Touch the preset switch to tune in the selected
station.
I
II
III
SIRIUS satellite radio information screen display
IV
Displays the SIRIUS satellite radio station name, current track name, artist, category, and
SIRIUS ID.
V
Touch FUNC .
● The function mode is activated.
VI
VII
VIII
IX
X
Touch
Info
.
XI
● The SIRIUS satellite radio information
screen will appear.
XII
● The SIRIUS ID is necessary when
subscribing to programs, etc.
XIII
XIV
XV
Turning off the radio
Press
.
● Press
again to turn on the radio
and to resume the SIRIUS channel
received prior to turning power off.
XVI
XVII
XVIII
XIX
213
How to operate the optional TV tuner (U.S.A./CANADA/KOREA/TAIWAN only)
How to use the TV
The unit can be used as a TV if a TV tuner (sold separately) is connected to the unit. The
vehicle must be safely parked with the parking brake engaged and the ignition switch in ON or
ACC before the TV can be viewed. If TV mode is selected while the vehicle is in motion, or
while the display is closed, only sound will be outputted.
Preset switches
WIDE switch
VTR switch
AUTO.P switch
MENU
button
POWER
button
SOURCE
button
TUNE·TRACK
button
Watching TV
Watching TV using the touch switches
Press MENU .
Touch TV .
Watching TV using the panel buttons.
Press SOURCE to select the TV source.
214
Selecting channel
Manual selection
Press
or
.
● Pressing the switch once moves the channel one step up or down.
(down): Lowers the channel
Automatic selection
or
II
III
(up): Raises the channel
Press and hold
I
until you hear a beep.
● The station that is closest to the current channel will be searched for automatically, and
searching will stop when the station is received. To stop the search before a station is
found, press the button again.
Selection when using preset switches
Touch a preset switch that already
has a station recorded.
● See “Saving TV channels” on next
page for more information.
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
After switching to the TV operation screen, touch switches will be displayed for
about 6 seconds. Touch the screen to display them again.
215
How to operate the optional TV tuner (U.S.A./CANADA/KOREA/TAIWAN only)
How to use the TV
Saving channels
There are two modes for saving channel, manual and AUTO.P.
Saving manually
Use manual tuning or automatic
tuning to select the channel to be
saved.
Choose a preset switch and press
and hold it until you hear a beep.
● The channel is set. Touch the preset
switch to tune in the selected channel.
Saving with AUTO.P
Press and hold AUTO.P until you hear 2 beeps in succession.
● The AUTO.P function will activate and start automatically selecting channels. You will
hear a beep when the automatic selection of channels is completed. Touch AUTO.P
again to switch the display back to the channel originally saved.
Changing stations saved by AUTO.P
Use manual tuning or automatic tuning to select the channel to be saved.
Press and hold the preferred preset switch until you hear a beep.
216
About AUTO.P
Because the AUTO.P function can be used to temporarily save channels for the
preset switches, channels saved manually will remain in memory even if AUTO.P is
used. Manually saving channels that are used regularly allows them to be restored
even after AUTO.P has been used, such as after traveling.
Touching AUTO.P while AUTO.P is operating or after it has been used will return
the preset memories to their previous settings. (The channel saved with AUTO.P will
be deleted.)
AUTO.P
Manual
II
III
IV
Press and hold
until you
hear 2 beep in succession.
I
AUTO.P
(Search started)
Automatically saving
channels to preset switches
V
VI
AUTO.P
(Search
completed)
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
●AUTO.P may not automatically receive channels if TV waves in the surrounding
area are weak.
●A channel saved with the tuning switch may not match the channel saved with
AUTO.P even though the signal is received from the same station.
●Due to conditions for receiving TV waves, saved channel may differ even when
the AUTO.P switch is operated repeatedly in the same location.
●Up to eight channels with good signal reception are automatically saved in order
of channel (low to high).
●When less than eight channels capable of reception are found, nothing is saved
for the remaining preset switches.
XVI
XVII
XVIII
XIX
217
How to operate the optional TV tuner (U.S.A./CANADA/KOREA/TAIWAN only)
How to use the TV
Checking preset stations
This recalls all the stations that have been preset either automatically or manually and plays
them each for 5 seconds.
Touch AUTO.P for less than 1
second.
● “P.SCAN” will be displayed, and the
preset stations will each be played
back for 5 seconds.
Touch AUTO.P for less than 1 second once more.
● The station that was being played when the switch was touched will then be played
continuously.
Switching to TV/VTR mode
It is possible to switch to VTR mode from TV mode when a VTR device is connected.
Touch VTR .
● Touching TV
will switch the display
to the TV operation screen.
To end TV mode
Press
.
● Press
again to turn on the TV and resume reception of the channel received
before power was turned off.
218
How to operate the VTR
How to use the VTR
Video tapes can be played by connecting a commercially available VTR deck. For safety
reasons, videos can be played only when the ignition is switched to ON or ACC and the
vehicle is completely stopped with the parking brake set. (If the VTR mode is activated while
the vehicle is in motion, only the audio will be played.)
I
II
III
IV
TV switch
WIDE switch
VTR2 switch
MENU
button
V
VI
VII
VIII
POWER
button
SOURCE
button
TUNE·TRACK
button
Viewing the VTR
Viewing the VTR using the touch switches
Press MENU .
Touch VTR .
● The VTR screen will be displayed.
● Touch the screen to display the VTR operation screen.
IX
X
XI
XII
XIII
XIV
XV
XVI
Viewing the VTR using the panel switches
XVII
Press SOURCE to select the VTR source when VTR device has been
connected.
XVIII
XIX
219
How to operate the VTR
How to use the VTR
Switching to the TV/VTR
It is possible to switch to VTR mode from TV mode when the optional TV tuner is connected.
Touch VTR in the TV screen.
● Touch TV to return to the TV operation screen.
●When two VTR devices are connected, VTR2 appears on the VTR operation
screen. Touch VTR2 to switch to the second VTR device.
●After switching to the VTR operation screen, touch switches will be displayed for
about 6 seconds. Touching the screen will display them again.
●The VTR operation screen can be displayed by touching the screen, even when
the VTR is playing.
●It is possible that the image may not be displayed correctly depending on the
connected devices.
220
Turning off the VTR mode
Press
● Press
.
again to resume playback.
● Press MENU and then touch VTR to resume playback of the video that was being
played before the power was turned off.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
221
How to operate the Back-eye Camera
Back-eye Camera operations
When the optional Back-eye Camera is installed, the rear view image can be displayed on the
monitor screen.
●Do not rely too heavily on the Back-eye Camera.
●Please use the Back-eye Camera as a backup means to check for obstructions
behind the vehicle.
●Raindrops or other natural phenomena may blur the camera's image.
●Do not backup your vehicle looking only at the monitor. Use the rear view mirror
and both side mirrors to check for any obstructions behind or around your
vehicle.
●Do not use the Back-eye Camera in the following situations:
• On frozen, slippery or snowbound roads
• With the trunk opened
• When using tire chains or a spare tire
• On a slope or any uneven road
●When the external air temperature is low, the image may darken or become faint.
Images of moving objects in particular may be distorted, or they may not be
visible on the screen, so the driver must directly confirm safety around the
vehicle visually.
222
I
II
III
IV
●The actual position and distance of people or objects may vary depending on the
features of the camera lens.
●Do not expose the camera to strong shocks such as hitting it or knocking it into
other objects. The Back-eye Camera may not function properly if the position of
the camera or its mounting angle is incorrect.
●The camera is waterproof. Do not uninstall, dismantle or reconfigure the unit.
Otherwise, the Back-eye Camera may not function properly.
●If the camera cover is rubbed strongly or a hard brush or abrasive is used to
clean it, the camera may get scratched, adversely affecting the image quality.
●The camera cover is made of plastic. Do not apply organic solvent, body wax, oil
remover, glass coating, etc. to it. If any of the above have been applied, wipe off
immediately.
●Pouring hot water on the Back-eye Camera to deice it in cold weather can lead to
a drastic change in temperature that may render normal operation impossible.
●The Back-eye Camera may not operate normally if the camera is damaged as a
result of it being hit. Immediately bring it to your local retailer for an inspection.
●Do not leave the unit in direct sunlight for long periods of time. Otherwise, a
printed image phenomenon may result.
●The range appearing on the monitor screen varies depending on the vehicle
model.
●The instant the vehicle is put in reverse, part of the monitor will appear white then
gradually stabilize.
●A white vertical band will appear when the camera is struck by light from the sun,
headlights or any other strong light beam source (Smear effect).
●After having used the Back-eye Camera for a long time, white scratches and
vertical lines may appear due to a rise in temperature, depending on the features
of the CCD.
●The 50 Hz power source range fluorescent light may cause flickering in the
screen. This is not a malfunction.
●Because the Back-eye Camera uses a special lens, the image and distance
appearing on the screen differs from the actual image and distance.
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
223
How to operate the Back-eye Camera
Back-eye Camera operations
Back-eye Camera image
Press FUNC for less than 1 second.
Touch CAMERA SCREEN .
● The rear image appears on the monitor
screen.
Automatic back-eye camera image display setting
The Back-eye Camera image can be set to automatically display when the ignition switch is
ON and the vehicle is shifted into reverse.
Press FUNC for less than 1 second.
Touch CAMERA SETTING .
● Touching the switch toggles between
AUTO and MANUAL.
224
I
II
III
IV
V
VI
VII
VIII
●The range of the image may vary depending on the vehicle and the road
conditions.
●There is a limit to the range of the camera. Objects near the ends of the bumper
and under the bumper cannot be seen.
●The rear image color may vary from that of the actual objects.
●In the following situations, the screen may be difficult to view but they do not
constitute a malfunction:
• In a dark area (such as at night)
• The temperature near the camera is high or low
• Raindrops are on the camera lens or the humidity is high (when raining)
• A foreign object is near the camera (such as mud)
• When the sun or a beam from headlights strikes the camera lens directly
• When a high-luminance point strikes the camera (such as the reflection of the
sun's rays on the chassis), a Smear effect* typical of CCD cameras may occur.
[Screen condition]
*Smear effect: A phenomenon where a
vertical line appears from a
high-luminance point striking
the camera (such as the
reflection of the sun's rays on
the chassis).
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
High-luminance point
225
For reference
Important Points
If one of these messages appears
If any of the following messages are displayed, check the unit while referring to the cause and
corrective action columns.
Messages
Corrective action
CD SEEK
Wait until the unit has finished
identifying the type of disc.
CD DOOR OPEN
The door of the CD changer is
open.
Close the door of the CD changer.
CHECK DISC
The CD/MP3/DVD is dirty or has
been inserted upside down.
Clean the disc if it is dirty. Insert the
disc correctly if it is upside down.
NO DISC
NO CD
There is no disc in the CD/MP3/
DVD player or CD changer.
Load a music disc.
The CD/MP3/DVD player or CD
changer will not play for some
reason.
Eject the disc. *1
The temperature of the CD/MP3/
DVD player or CD changer has
become unusually high.
Wait a moment for the unit to cool
down. Do not perform any other
operations. *2
NO CD MAGAZINE
There is no magazine in the CD
changer.
Load a magazine.
CD OO CHECK
The OO spot in the CD changer
has a CD that cannot be read.
Check for a properly loaded music
CD.
PASS CODE INCORRECT
Displayed when the pass code has
been entered incorrectly.
Enter the correct pass code.
This “Memory Stick” is not
available.
The inserted “Memory Stick Duo”
type is not supported.
Check that the “Memory Stick Duo”
is a type supported by this unit.
(See page 34)
No “Memory Stick”.
An “Memory Stick Duo” has not
been inserted.
Insert an “Memory Stick Duo”.
Checking “Memory Stick”.
The “Memory Stick Duo” is being
checked.
Checking the “Memory Stick Duo”
may take a short while. Wait a
moment for the message to
disappear before using.
Please check “Memory Stick”.
The “Memory Stick Duo” cannot be
played because of static electricity.
Wait a moment then re-insert and
attempt to play again.
This “Memory Stick” is not
available.
You have tried to save data to the
this unit from a “Memory Stick Duo”
not supported by this unit.
Check that the “Memory Stick Duo”
is a type supported by this unit.
(See page 34)
CD ERROR
DVD ERROR
DISC ERROR
226
Cause
The CD changer is searching for
discs when a magazine has been
inserted in the CD changer.
*1
If the unit still will not work after the disc is ejected, contact your local retailer.
*2
If this error occurs, wait a moment for the changer to cool down. When the temperature
inside the unit returns to normal, the message will disappear and playback will start. If
the message does not disappear after waiting for a long period, contact your local
retailer.
Messages
Cause
Corrective action
Viewing restrictions are enabled.
Change the setting for viewing
restrictions and start again. (See
page 125)
A function that has been disabled
was selected with the menu.
Follow the directions on the screen
and start again.
A function that cannot be used
while the vehicle is in motion was
selected.
Stop the vehicle.
INVALID CODE
A number not supported was input
for selecting a language code.
Input a valid language code.
REGION CODE ERROR
The region code (controlled region
for playback) of the disc isn't
acceptable.
Check that the DVD is a type
supported by this unit. (See page
108)
ANTENNA
The SIRIUS antenna is
disconnected.
Check the connection of the
SIRIUS antenna.
ACQUIRING
Displayed when the signal is lost
(during access).
Try receiving the signal again in the
place where there are no
obstacles.
CALL888-539-SIRIUS
You are tuned to a valid channel
but you are not subscribed to that
channel.
Subscribe to SIRIUS. Or, check/
change your subscription plan.
SUB UPDATED
Displayed when your channel
subscription has been accepted
and your status is being updated to
allow you to receive the channels.
After this message is displayed, the
channels for which you do have a
subscription can be received.
INVALID
Displayed when you are tuned to a
channel that you cannot receive.
Tune to channels that you can
receive.
UPDATING
Displayed while the channel map is
being updated.
After this message is displayed,
subscribe to SIRIUS. The channels
for which you do have a
subscription can be received.
PARENTAL LOCK ENABLED
THIS FUNCTION IS CURRENTLY
DISABLED
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
227
For reference
Important Points
Before asking for repairs
Slight differences in operation can sometimes be mistaken for malfunctions, so check the
following table before requesting any repairs.
If the following fail to solve the problem, contact your local retailer.
Symptom
Corrective action
This is a characteristic of LCDs.
This is not a malfunction. Wait for a
brief period.
The display is distorted for a brief
period after the power is turned on.
This is a characteristic of LCD
backlighting.
This is not a malfunction. The
display will stabilize after a brief
period.
No sound comes out.
Volume is poorly adjusted.
Press the volume switch and check
volume.
A speaker wire is disconnected.
Check the connections of the
speaker wires.
Volume is poorly adjusted.
Check the left/right volume
adjustments.
The adjusted audio quality is not
included in the radio broadcast or
disc.
Check by changing the radio
station or disc.
Power is not turned on.
Turn the vehicle’s ignition switch to
[ACC] or [ON].
A disc is already inserted and you
are trying to insert a second disc.
Eject the previously inserted CD/
DVD and insert the preferred CD/
DVD.
There is water condensation in the
deck.
Do not use the deck for a while and
then try using it again. (See page
31)
There is a large scratch or warp in
the CD/DVD.
Insert a different CD/DVD.
The CD/DVD is very dirty.
Clean the CD/DVD.
(See page 32)
The CD/DVD is upside down.
Insert the CD/DVD the correct way.
(See page 32)
The inserted CD/DVD type is not
supported.
Insert a CD/DVD that is supported
by the unit. (See page 31, page 32)
The CD changer is not completely
connected.
Check the connections to the CD
changer.
The parking brake has not be set.
Set the parking brake.
The vehicle ignition switch has not
been turned on.
Turn the vehicle ignition switch to
[ACC] or [ON].
The connection wires/cables is not
completely connected.
Check all connections.
VTR mode is activated.
Touch TV and select the
channel.
Sound comes out of only one side
(left or right, front or back).
Sound quality does not change
even after making adjustments.
A CD/DVD will not go into the deck.
A CD/DVD cannot be played.
CDCH
not displayed on the
screen.
Audio is outputted, but not TV or
DVD video. (With vehicle stopped.)
Neither video nor audio is output.
TV image nor audio is outputted.
228
Possible reason
The screen is dark for a brief period
when the power is turned on at low
temperatures.
Symptom
Possible reason
Corrective action
There is a point of light on the
display.
At least 99. 99% of the pixels on
the LCD panel are effective, but it is
possible that 0. 01% of the pixels
may not light or may stay lighted.
This is not a defect, so please use
the deck in this condition.
The Audio screen is distorted by
electrical noise.
Are electrical devices that generate
electrical noise being used in the
vicinity of the unit?
For example, devices generating
high voltage (such as those that
generate negative icons) or high
frequency electromagnetic waves
(cell phones or two-way radios)
Use such equipment as far away
from the unit as possible.
If such equipment continues to
affect the unit, even from a
distance, refrain from using such
equipment while the unit is in
operation.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
229
For reference
Other
Products equipped with Dolby Digital
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, lnc. All rights reserved.
Manufactured under license from Dolby Laboratories, Inc.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, lnc. All rights reserved.
Products equipped with Macrovision
This unit includes copyright protection technology used in accordance with US patents and
other intellectual property rights owned by Macrovision Corporation and other entities. Use of
this copyright protection technology requires approval from Macrovision Corporation and the
technology must not be used for audiovisual purposes aside from general household use
without special approval from Macrovision Corporation. Modification and disassembly of this
technology is prohibited.
230
For reference
Glossary
CD-R
(Compact Disc Recordable)
CD-DA
(Compact Disc Digital Audio)
CD-RW
(Compact Disc ReWritable)
EQ (Equalizer)
MP3
(MPEG-1 Audio Layer-3)
LPCM
(Linear PCM)
MPEG
Copy Control CD
UDF
(Universal Disc Format)
This is a disc that can only be recorded once.
Recorded data cannot be deleted. There are two
types of CD-R, one having a capacity of 650MB
(74 minutes of music), the same as a regular CD,
and the other having a capacity of 700MB (80
minutes of music).
This disc is the standard for recording and playing
of music data. One track is recorded with one
song, and a maximum of 74 minutes can be used
with the CD.
This disc uses a phase transformation method
that enables recording and deleting of data as
many times needed. The capacity is 700MB (80
minutes of music).
This enables setting of emphasis on certain
sounds in the bass-treble range to achieve the
preferred tonal profile. Levels can be adjusted to
personal preference, enhancing enjoyment of the
music.
MP3 stands for MPEG Audio Layer III, the
standard format for audio compression
technology. MP3 can compress files to one-tenth
the original size because they compress inaudible
sounds found in areas of the spectrum beyond
human hearing.
This is an abbreviation for Linear Pulse Code
Modulation, a signal recording method used with
music CDs. A music CD is recorded at 44.1kHz/
16 bit, but a DVD is recorded at 48kHz/16 bit ~
96kHz/24 bit, enabling a DVD to be played with
higher sound quality than a music CD.
This is an abbreviation for Moving Picture Experts
Group and is pronounced “empeg”. It is the
international standard for moving image
compression. With DVDs, this method is also
used to compress and record digital audio.
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
This is a CD that has controls for preventing
computers from copying and ripping (taking audio
information recorded on a compact disc and using
it as data to create a file).
XVII
This is one format for use with optical discs not
reliant on the OS. It is used with media such as
DVD and CD-RW.
XIX
XVIII
231
For reference
Glossary
Track
Viewing Restriction
This is a DVD video function that “Restricts
playing of discs that support viewing restrictions,
in accordance with the regulated levels of each
country.” Restrictions differ by DVD video and
may completely prevent playing of the video or
may skip or insert alternate scenes for extreme
scenes.
Title
This is the largest unit for divisions of video or
songs recorded on a DVD video. Usually a single
movie is treated as a title by video software and a
single album (or song) is treated as a single title
by music software. The consecutive numbers
attached to titles are called title numbers.
Chapter
This is a unit for divisions of video or songs
recorded on a DVD video, but it is a smaller unit
than a title. A single title is made up of several
chapters, and the consecutive numbers attached
to chapters are called chapter numbers.
Multi-Angle
This is one feature of DVD video, where
viewpoints of the same scene are changed by
recording from several different angles (camera
positions), allowing the viewer to select the
preferred angle.
Multi-Language
This is one feature of DVD video, where the same
scene is recorded with several different
languages and subtitles, allowing the viewer to
select the preferred language.
Region code
DVD players and DVD discs have a region code
that enables playing by geographic marketing
regions, and a disc cannot be played if the
number recorded on the disc is not included in the
region codes of the player. See page 108 for
details on region codes.
(Region code)
232
The single division for a song on a music CD is
called a track.
For reference
About care and maintenance
About care and maintenance - main unit
● Use a soft cloth (silicon cloth) to remove dirt from the main unit.
If the unit is very dirty, soak a cloth in diluted kitchen detergent, wring dry, then use it to wipe
the unit clean. Finally, wipe down with a dry cloth.
Take care when
cleaning the touch
panel as it is easily
scratched.
I
II
III
IV
V
Use any cloths made from artificial fibers in accordance with the relevant cautionary
instructions.
VI
● Do not use volatile chemicals such as benzine or thinner.
VII
VIII
IX
X
XI
XII
Otherwise, the unit may be damaged or the coating may peel.
XIII
XIV
XV
XVI
XVII
XVIII
XIX
233
For reference
Topic index
About screen and sound adjustment
[Regarding screen adjustment]
To make the audio operation screen or DVD·TV·VTR screen easier to see
"Adjusting image quality" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P71
To change the wallpaper
"Setting the Background" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P66
To set the screen to wide mode
"Switching screen mode". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P72
[Regarding audio adjustment]
To change the volume
"Adjusting the main volume". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P52
To turn on/off the guide tone used at switch operation
"Setting the Guide tone" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P77
To adjust sound quality
● To simulate Multichannel
"Setting Circle Surround II" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P55
● To adjust parametric equalizer
"Adjusting PEQ (parametric equalizer)" . . . . . . . . . . . . . . . . . . . . . . . . . P56
● To switch the sound image localization to match the position of passengers
"Adjusting POS (Positioning selector)" . . . . . . . . . . . . . . . . . . . . . . . . . P58
● To adjust the left/right/front/rear balance
"Setting the balance" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P59
234
● To adjust the MP3/WMA sound
"Setting the harmonizer" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P60
● To add sharpness when listening at low/high volumes
"Setting LOUDNESS" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P60
● To adjust time alignment
"Simplified time alignment settings (Time Alignment)" . . . . . . . . . . . . . . P61
● To change the sub woofer settings
"Setting sub woofer" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P63
About using AM/FM radio
To play the radio
"Listening to the AM/FM radio" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P80
To search for a radio station
"Selecting radio stations" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P81
To save radio stations
"Saving radio stations" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P82
To check preset stations
"Checking preset stations" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P83
To create station name
"Creating a station name" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P84
About using the CD player and CD changer
To play a CD
"Listening to a CD" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P87
To select a song or CD
"Selecting a track" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P88
"Selecting a CD" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P104
To repeat the song or CD currently being played
"Repeating a track". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P88
"Repeating a track or CD" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P104
To play songs in a different order
"Playing tracks in random order" . . . . . . . . . . . . . . . . . . . . . . . . . . P88, 105
To fast-forward or rewind
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
"Fast-forwarding/rewinding" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P88
235
For reference
Topic index
About using the MP3/WMA player
To play an MP3/WMA file
"Playing MP3/WMA" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P93
To select a music file or folder to listen to
"Selecting a music file" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P94
When you want to return to a level or don't know the current level
"Changing display of the current level" . . . . . . . . . . . . . . . . . . . . . . . . . P95
To repeat the same music file
"Repeating the same music file or folder" . . . . . . . . . . . . . . . . . . . . . . . P96
To play songs in a different order
"Playing music files in random order" . . . . . . . . . . . . . . . . . . . . . . . . . . P97
To learn about MP3/WMA
"About MP3/WMAs" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P98
To learn about making MP3/WMA files
"Making and playing MP3/WMA files". . . . . . . . . . . . . . . . . . . . . . . . . . P102
236
About using the DVD player
To play a DVD video
"Watching a DVD" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P110
To learn about discs
● To learn about the marks displayed on discs and packages
"About marks displayed on discs" . . . . . . . . . . . . . . . . . . . . . . . . . . . . P108
● To learn about discs that can be played
"About playable discs". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P107
● To learn about disc structures
"About DVD disc structures" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P109
To operate the menu recorded on a disc
"Operating the disc menu". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P116
I
II
III
IV
V
VI
VII
VIII
IX
To operate the video being played
"Operating the video" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P112
To select/search for a video
"Searching by chapter" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P118
To change subtitles, audio or the video angle
"Changing the angle" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P118
"Switching subtitle language" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P119
"Switching dubbed audio language" . . . . . . . . . . . . . . . . . . . . . . . . . . P119
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
237
For reference
Topic index
To set the player
"Setting the audio language". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P121
"Setting subtitle language" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P122
"Setting menu language" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P123
"Setting display of multi-angle mark (angle selection mark)" . . . . . . P124
"Setting viewer restriction" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P125
"Changing video output" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P126
To use the VTR
"How to use the VTR" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P219
About video CD player (Asia only)
To play a video CD
"Watching a video CD" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P129
To operate the menu recorded on a disc
"Using the menu screen" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P130
To select a track
"Advancing to the next scene or returning to the beginning of
the scene being played". . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P131
About Area Shot (U.S.A./CANADA only)
To use Area Shot function
"To use the Area Shot function" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P135
To read Area Shot data
"Reading Area Shot data" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P138
To change Area Shot screen
"Changing Area Shot screen" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P140
To learn about Area Shot screen
"How to view the Area Shot screen" . . . . . . . . . . . . . . . . . . . . . . . . . . . P141
To switch map reduction scale
"Switching the map reduction scale" . . . . . . . . . . . . . . . . . . . . . . . . . . P143
To switch guidance points
"Switching guidance points" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P144
To display POI vicinity
"Displaying POI vicinity" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P146
238
About ESN security
To learn about ESN
"About ESN" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P149
To switch security type
"How to switch the security type
(Key CD security/"Memory Stick" security)" . . . . . . . . . . . . . . . . . . . . P150
To set security function
"How to program the Key CD" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P151
"How to record a security code" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P155
To cancel security function
"How to cancel the Key CD" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P152
"How to cancel the “Memory Stick” security" . . . . . . . . . . . . . . . . . . . P157
To resume normal operation
"How to resume normal operation (ESN security lock out)" . . . P153, 159
To operate ACC security
"How to operate the ACC security". . . . . . . . . . . . . . . . . . . . . . . . . . . . P163
I
II
III
IV
V
VI
VII
VIII
IX
About optional 5.1ch decoder & AV selector unit
To adjust sound quality
● To adjust parametric equalizer
"Adjusting PEQ (Parametric equalizer)" . . . . . . . . . . . . . . . . . . . . . . . . P178
● To measure frequency characteristics
"Measuring/Displaying frequency characteristics" . . . . . . . . . . . . . . . P181
● To switch the sound image localization to match the position of passengers
"Adjusting POS (Positioning selector)" . . . . . . . . . . . . . . . . . . . . . . . . P183
● To adjust the left/right/front/rear balance
"Setting the balance" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P184
● To adjust the MP3/WMA sound
"Setting the harmonizer" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P185
● To add sharpness when listening at low/high volume
"Setting LOUDNESS" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P185
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
● To adjust the surround system
"Setting/Adjusting surround system". . . . . . . . . . . . . . . . . . . . . . . . . . P186
239
For reference
Topic index
● To set speakers
"Setting/Adjusting speakers" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P189
● To import sound quality data
"Importing sound data" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P198
To set display
● To set external monitor image
"External monitor image settings" . . . . . . . . . . . . . . . . . . . . . . . . . . . . P201
About optional HD radio (U.S.A. only)
To play radio
"Listening to the HD radio" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P202
To search for a radio station
"Selecting radio stations" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P203
To save radio stations
"Saving radio stations" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P204
To check preset stations
"Checking preset stations" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P205
To display information screen
"HD radio information screen display" . . . . . . . . . . . . . . . . . . . . . . . . . P206
To set reception
"HD radio reception settings" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P207
About optional SIRIUS satellite radio (U.S.A. only)
To play radio
"Listening to the SIRIUS satellite radio". . . . . . . . . . . . . . . . . . . . . . . . P209
To search for a radio station
"Selecting SIRIUS channels" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P210
To save radio stations
"Saving SIRIUS channels" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P213
To display information screen
"SIRIUS satellite radio information screen display" . . . . . . . . . . . . . . P213
240
About optional TV (U.S.A./CANADA/KOREA/
TAIWAN only)
To watch radio
"Watching TV" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P214
To search for channel
"Selecting channel" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P215
To save channels
"Saving channels" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P216
About optional Back-eye Camera
To operate Back-eye Camera
"Back-eye Camera image" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P224
I
II
III
IV
V
VI
VII
When something isn't clear
VIII
When you don't understand a screen message
IX
"If one of these messages appears" . . . . . . . . . . . . . . . . . . . . . . . . . . . P226
X
When you think the deck may have a problem
"Before asking for repairs" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P228
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
241
For reference
Index
A
Adjusting the main volume ....................... 52
Adjusting sound quality...........................53
ANGLE..................................................118
AUTO.P ..................................................82
B
BRIGHT ..................................................71
C
POS (position selector) ............................ 58
R
RANDOM ................................. 88, 97, 105
REPEAT ................................... 88, 96, 104
S
Saving radio stations .............................. 82
Setting LOUDNESS ............................... 60
CD-R (CD-Recordable)...........................31
Setting the BEEP tone............................ 77
CD-RW (CD-ReWritable)........................31
Switching dubbed audio language ....... 119
Circle Surround II....................................55
Switching subtitle languages ................ 119
COLOR ...................................................71
CONTRAST ............................................71
H
HOME .....................................................95
T
TINT ....................................................... 71
V
How to use the remote control..............165
Volume balance...................................... 59
How to use the AM/FM radio ..................80
VOL button ............................................. 52
How to use the Area Shot function .......137
How to use the CD changer..................103
How to use the CD player.......................87
How to use the DVD player ..................110
How to use the HD radio.......................202
How to use the MP3/WMA player...........92
How to use the SIRIUS satellite radio...208
How to use the TV ................................214
How to use the video CD player ...........129
How to use the VTR..............................219
M
Multi-angle mark ...................................118
N
NORMAL mode ......................................73
242
P
W
Wallpaper (background) ......................... 66
WIDE 1 mode ......................................... 73
WIDE 2 mode ......................................... 73
WIDE 3 mode ......................................... 73
Woofer.................................................... 63
For reference
Specifications
Display
Liquid crystal panel
Screen dimensions
Pixel count
Active pixel rate
Display format
Drive system
Usage temperature range
Storage temperature range
7” type wide low reflection panel
154.08 mm (W) x 87.048 mm (H)
336,960 pixels (480 (H) x3 x 234 (V))
Over 99.99%
Transmissive color filter format
TFT (thin membrane transistor) active matrix
format
-20 to +65°C (-4 to +149°F)
-40 to +85°C (-40 to +185°F)
Radio tuner
Reception frequency
● U.S.A./CANADA:
● Asia:
● Australia:
Practical speed
Frequency characteristic
Stereo separation
● AM22PV (S/N20dB)
● FM13dBf (new IHF)
30 to 15,000Hz (FM)
38dB (1kHz)
Below measurement limit
0.03% (0dB, 1kHz)
20 to 20,000Hz
88dB (1kHz)
85dB
DVD
Total harmonic distortion
Frequency characteristic
S/N ratio
II
III
IV
V
AM530 to 1710 kHz
FM87.75 to 107.9 MHz
AM522 to 1629 kHz
FM87.5 to 108.0 MHz
AM522 to 1710 kHz
FM 87.5 to 108.0 MHz
CD
Wow & flutter
Higher harmonic distortion
rate
Frequency characteristic
S/N ratio
Dynamic range
I
0.3% (1kHz, 0dB, 0.5W output)
20 to 20,000Hz
85dB (1kHz)
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
243
For reference
Specifications
Common component
Rated output
Maximum output
Suitable load impedance
Power source voltage
Power consumption
Exterior dimensions
Weight
244
15W x 4 (1kHz, 1%4:) (EIAJ)
50W x 4 (test voltage 14.4V)
4: (each channel)
DC13.2V (11-16V)
Grounded
0.5W x4 output time about 3.5A
About 15A max
180mm (W), 50mm (H), 165mm (D)
About 3.6kg
For reference
How to contact customer service
Should the product require service, please contact your nearest Eclipse dealer.
<U.S.A./CANADA>
Fujitsu Ten Corp. of America
19600 South Vermont Avenue, Torrance, CA 90502
Phone: (310) 327-2151
<AUSTRALIA>
Fujitsu Ten (Australia) PTY LTD.
89 Cook Street Port Melbourne, Victoria 3207, Australia
Phone: 1800 211 411
<MALAYSIA>
CSE Automotive Technologies Sdn. Bhd.
Level 5, Axis Plaza, Jalan U1/44, Glenmarie, 40150 Shah Alam,
Selangor D.E., Malaysia.
Phone: 03-5569-4200
Fax: 03-5569-4201
<SINGAPORE>
Cobra Singapore Pte Ltd
#07-02 King’s Centre 390, Havelock Road Singapore 169662
Phone: 6737 2568
Fax : 6737 9538
I
II
III
IV
V
VI
VII
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
245
For reference
How to contact customer service
<KOREA>
Transpectra Co., LTD.
115-16 nonhyun dong kangnam ku Seoul, Korea.
Phone: 02-540-4595
Fax: 02-2-540-4666
<TAIWAN>
Sentrek Taiwan, LTD.
1, 9F, Lane 155, Section 3, Peishen RD., Shenkeng, Taipei Hsien, 222
Taiwan, R.O.C.
Phone: 02-2662-8110
Fax: 02-2662-8117
<THAILAND>
Sho-Ten Co., Ltd.
114/9 Soi Suwansawadi, Thungmahamek, Rama 4 Rd., Sathorn,
Bangkok 10120, Thailand.
Phone: 02-671-9610-12
Fax: 02-671-9614
246
Before installation
Before installation
● Note ●
Be sure to disconnect the vehicle battery's negative terminal
before installing the main unit.
II
Components
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
I
Item
Main unit
Mounting sleeve
Side bracket
Bezel
Bushing
Thin flat screw (4 x 5 mm)
Flat head screw (4 x 6 mm)
Interconnecting cable (16P)
Interconnecting cable (20P)
Splicing connector
Remote control
Pan screw with washer (Blue: 4 x 3 mm)
Battery
Antenna extension cable
Case (For detachable panel)
Q'ty
III
1
1
2
1
1
4
4
1
1
2
1
4
2
1
1
IV
VI
VII
VIII
IX
X
XI
XII
Installation preparation
Before the main unit installation, be sure to remove the caution tag and the caution label.
CAUTION TAG
V
CAUTION
CAUTION LABEL
XIII
XIV
XV
XVI
XVII
MAIN UNIT
● Note ●
In the event that the main unit requires shipping, re-attach the
caution label to help prevent potential damage that may be caused
by shipping.
XVIII
XIX
247
Mounting instruction
Mounting instruction
Mounting the main unit
-If installing the main unit by the mounting sleeveInsert the mounting sleeve into the opening in the vehicle dash board or
console box.
Use a screwdriver or a similar tool to bend the tabs in the mounting sleeve
to secure the mounting sleeve.
BEND THE MOUNTING
TABS.
DASH BOARD
OR CONSOLE BOX
2
248
MOUNTING
SLEEVE
Attach the side brackets to the main unit using flat head screws.
● Note ●
● Connect all cables before installing the main unit.
I
● Be sure to use the accessory mounting screws (M4 x 6) as the
mounting screws. If any other screws are used, they may
damage the inside of the unit.
II
1 MAIN UNIT
III
IV
V
7 FLAT HEAD SCREW [x 2]
(4 x 6 mm)
VI
VII
3 SIDE BRACKETS [x 2]
NOTES
By adjusting the positions of the brackets, the main unit's installed depth can be adjusted.
example 1
example 2
1 MAIN UNIT
1 MAIN UNIT
FRONT OF
VEHICLE
FRONT OF
VEHICLE
3 SIDE
BRACKET
IX
X
XI
SCREW
POSITION
SCREW
POSITION
VIII
3 SIDE
BRACKET
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
XX
249
Mounting instruction
Mounting instruction
Mount the stud bolt to the main unit.
Insert the main unit into the mounting sleeve until it locks in place.
Install the bezel on the main unit.
METAL OF
VEHICLE
DASH BOARD
OR CONSOLE BOX
5 BUSHING
2 MOUNTING SLEEVE
4 BEZEL
-If installing the main unit using the side brackets of the vehicle-
● Note ●
Connect all cables before installing the main unit.
Remove the pockets and any other accessories from the center cluster to
make room for the main unit.
Remove the mounting side brackets for the pocket.
CENTER CLUSTER
POCKET
SCREWS
250
Attach the side brackets to the main unit.
● Note ●
Be sure to use the accessory mounting screws (M4 x 6) as the
mounting screws. If any other screws are used, they may damage
the inside of the unit.
I
II
Install the main unit in the vehicle.
III
● Note ●
IV
Be careful not to push the main unit display or the buttons too
strongly when installing the main unit to the vehicle, otherwise the
main unit and buttons may become damaged.
V
If using these installation holes, be sure to
use the 12 Pan screw with washer (Blue: 4 x 3 mm)
VI
VII
VIII
6 THIN FLAT SCREW (4 x 5 mm)
IX
X
1 MAIN UNIT
SCREWS [x 4]
POCKET
SIDE BRACKETS
NOTES
By adjusting the positions of the brackets, the main unit's installed depth can be adjusted.
example 1
example 2
1 MAIN UNIT
FRONT OF
VEHICLE
XI
XII
XIII
XIV
1 MAIN UNIT
FRONT OF
VEHICLE
XV
XVI
SCREW POSITION
SCREW POSITION
● Caution ●
When installing the main unit, be sure to the supplied mounting
hardware. If parts other than those supplied are used, the main
unit may be damaged internally.
XVII
XVIII
XIX
XX
251
Mounting instruction
Mounting instruction
Names and function of terminals
● Caution ●
Never connect the power supply to the speaker leads, otherwise it
causes damage to the main unit.
● Note ●
To prevent unconnected leads from shorting out, insulate them by
wrapping their tips with electrical tape. Similarly, insulate all the
connected leads.
If an external amplifier is to be connected to the main unit, be sure
to ground its outside chassis to the vehicle body (a metal part).
1 MAIN UNIT
9
14 ANTENNA EXTENSION CABLE
ANTENNA PLUG
20P
15
13
16
17
12
11
10
16P
18
n
ee
Gr
20
21
e
Blu
9 INTERCONNECTING
ow
CABLE
ll
Ye
e
d
Re
1
e 19
hit
/W
d
Re
/
ge
an
Or
2
it
Wh
8 INTERCONNECTING
CABLE
lue
3
e
B
it
Wh
e/
Blu
4
22
n
ow
Br
5
6
ck
Bla
7
8
● Caution ●
Installation is not possible for vehicles without ACC.
252
k
lac
n/B
ow
Br
No.
Name
Wire color
Destination
1
B+
Yellow
Connect where the power is constantly available,
regardless of the ignition switch's position.
2
ACC
Red
Connect where the power comes on when the ignition is
in the ACC position.
3
Illumination power supply
Orange/white
Connect to where power comes on when the vehicle
light switch is turned on.
II
4
Antenna power supply
Blue
Connect to the automatic antenna control terminal of the
vehicle.
III
5
External amp turn on
Blue/white
Connect to the control terminal for the external amp turn
on.
IV
6
Speaker output leads
(Front)
Connect to the front speakers.
V
7
Speaker output leads
(Rear)
8
Ground
White: Left +, White/Black: Left Gray: Right +, Gray/Black: Right -
Connect to the rear speakers.
Green: Left +, Green/Black: Left Purple: Right +, Purple/Black: Right -
Black
I
VI
VII
Connect where good body grounding is available.
VIII
9
E-LAN terminal (13P)
Connect to the E-LAN terminal of the CD changer, etc.
10
Front line-out terminals
Connect to the RCA connector of an external amplifier.
11
Rear line-out terminals
Connect to the RCA connector of an external amplifier.
IX
12
Line-out terminals
(Non-fader)
Connect to the RCA input connectors of a EQ, or the
RCA input connectors of a woofer amplifier.
X
13
GPS antenna terminal (8P)
Connect to the GPS unit.
14
Radio antenna receptacle
Connect to the radio antenna of the vehicle.
XI
15
Back-eye camera external input
terminal (4P)
Connect when using a back-eye camera (sold
separately) with the system.
XII
16
Connect to the output cable of external video equipment
such as a VTR.
XIII
VTR input terminals
Connect to the monitor with video input.
XIV
Yellow: Video signal, White: Audio (left) signal
Red: Audio (right) signal
XV
Connect to the digital input connectors of an auxiliary
unit.
XVI
Red/white
Connect to the parking brake signal terminal.
Green
Connect the reverse signal output of the vehicle to this
terminal when connecting a back-eye camera.
XVII
Reverse signal
DVD-MUTE output
Blue
Connect to the DVD-MUTE input terminal.
17
VTR output terminals
18
Digital output terminal
19
Parking brake signal
20
21
22
Yellow: Video signal, White: Audio (left) signal
Red: Audio (right) signal
Steering remote control terminal
Connect to the vehicle steering remote control.
* Compatible vehicle models for installation :
Vehicle with voltage detection-type steering
remote control. Ask your dealer for details.
XVIII
XIX
XX
253
Mounting instruction
Mounting instruction
Connecting the parking-brake signal and the reverse signal
● Warning ●
Verify the parking-brake signal and the reverse signal before
making the signal connection. Using the wrong wires may cause
accidents or malfunctions.
● Note ●
The connecting point for the parking-brake signal and the reverse
signal may vary with models and grades. Check with your nearest
car dealer regarding remove details.
A connecting point for the parking-brake signal
(example)
HAND OPERATED
PARKING BRAKE
ATTACH A SPLICING
CONNECTOR AT THIS LOCATION
PARKING BRAKE
SIGNAL-CABLE
PARKING BRAKE
LAMP
FOOT OPERATED
PARKING BRAKE
A connecting point for the reverse signal
(example)
ATTACH A SPLICING
CONNECTOR AT THIS LOCATION
REVERSE LAMP
REVERSE SIGNAL CABLE REVERSE SIGNAL CABLE
254
Insert the connection wire [parking brake signal wire (red/white), reverse
signal wire (fresh green)] of the main unit and the vehicle’s wire into the
splicing connector.
I
Push in the terminal (the metal part) of the splicing connector using a pair of
pliers.
II
Press down the cover of the splicing connector and squeeze it until it locks.
III
PARKING BRAKE
SIGNAL WIRE (RED/WHITE) OR
REVERSE SIGNAL WIRE
(FRESH GREEN)
COVER
IV
V
VI
CABLE IN THE CAR
VII
10 SPLICING
CONNECTOR
10 SPLICING CONNECTOR
VIII
IX
X
XI
XII
XIII
XIV
XV
XVI
XVII
XVIII
XIX
XX
255
Mounting instruction
Mounting instruction
System connection example
1) AVX5000 + GPS105
GPS ANTENNA
(Supplied with GPS 105)
GPS UNIT
(Supplied with GPS 105)
8P
INTERCONNECTING CABLE
(Supplied with GPS 105)
1 MAIN UNIT
9
14 ANTENNA EXTENSION CABLE
L NT
L
NA ME
NA
R
ER UIP
T
SIG
ITO
N
E
EX EQ
O
AK
TO EO
EM
L
BR
16 VID
G
TH
NA
N
I
O
IG
K
T
S
7
R
1
SE TE
PA
O
ER
ite T REV
MU
h
DW
/
Red een TO O DV
T
Gr ue
Bl
INTERCONNECTING CABLE
8 INTERCONNECTING
OL
NG R
CABLE
RI ONT
E
E C
ST E
O OT
2 T EM
2
R ck
wn
Bro
Bla
wn/
Bro
15
8P
20P
NO CONNECTION
(Do not remove cap)
16P
ll
Ye
)
ply
t
en
an
erm
p
su
d
Re
n
Ora
ly)
p
up
rs
e
ow
18
ow
)
on
ti
ina
ge/
Wh
9
ite
e
Blu
e
hit
/W
e
Blu
)
P
ply
(P
um
V(
C
up
(Ill
12
(S
AC
H
+
ly)
Y
C
Y
A
pp
TO
IT
ER
EL
Su
W
(
T
R
S
T
IT
A
BA
HT
UN
NN
LIG
TO
TE
CH
N
D
A
ER
A
E
RA
AK
HE
OF
PE
WE
D
S
TO
O
A
T
P
LE
ON
ER
TO
N
FR
AK
-O
N
PE
R
S
U
T
AR
TO
RE
256
Bla
ck
TO GROUND
2) AVX5000 + TVR105 + CH3083
1 MAIN UNIT
14 ANTENNA EXTENSION CABLE
I
ANTENNA PLUG
9 INTERCONNECTING CABLE
20P
15
17
TV TUNER (Supplied with TVR105)
18
NO CONNECTION
(Do not remove cap)
INT
CA ERC
(So BLE ONNE
ld s
CTI
epa
NG
rate
ly)
16P
TO ACC
(POWER Supply)
Red
)
ion
TE
ite
/Wh
nge
e
Blu
RC
ON
HT t
e/W
A
Blu
LIG ina
NN
wn
Bro
lack
AD (Illum
TE
F
E
F
wn/B
N
H H
O
Bro
R Aply)
TO ITC
ADly)
E
E
p
L
SW POW(Su ON L upp
Y
G TRO
N (S
TOELA
URUNIT ERINON FRONT
T
R
E C
TOACH
SPEAKER
ST TE
E
TOEMO
REAR
R
hite
VI
6P
5P
VII
T
NE
CT
IN
G
CA
AL EN
RN M
TE UIP
EXO EQ
O
T IDE
V
BL
E
VIII
ND
IX
ROU
G
TO
TO GROUND
SPEAKER
ANTENNA SELECTOR
(Supplied with TVR105)
TO GROUND
TO GROUND
IV
13P
5P
IN
III
V
12P
CONNECTION
8
Ora
TO GROUND
16 NO
ow
Yell
V
+12
RY upply)
E
T
s
BAT ent
TO arman
(P
19
e 20
hit
21
d/Ween
e
R Gr lue
B
13P
VIDEO INPUT
13
II
X
XI
XII
XIII
INTERCONNECTING CABLE
(Supplied with TVR105)
CH3083
DIGITAL OUT
(Do not remove cap)
INTERCONNECTING CABLE
(Supplied with CH3083)
XV
13P
2P
TV ANTENNA
(Supplied with TVR105)
TO GROUND
XIV
INTERCONNECTING CABLE
(Supplied with CH3083)
XVI
XVII
XVIII
XIX
XX
257
Mounting instruction
Mounting instruction
3) AVX5000 + DCU105 + CH3083
N
TIO
EC
N
ON
LE
B
CA
ING 5)
CT U10
E
B
C
NN D
CO with
V
ER ied
+12 )
INTuppl
RY ply
(S
NO
n
row
ck
Bla
TO GROUND
llow
Ye
FRONT
SPEAKER
C
TE sup
BAT ent
TO erman
(P
MICROPHONE
(supplied with DCU105)
INTERCONNECTING CABLE
(Supplied with CH3083)
DIGITAL OUT
(Do not
REAR
remove cap)
SPEAKER
e
Blu
INTERCONNECTING CABLE
(Supplied with DCU105)
NAVI-VOICE SIGNAL(No connection)
16P
DCU105
DIGITAL INPUT
VIDEO OUTPUT
CH3083
12P
13P
2P
13P
k
lac
B
TO GROUND
1 MAIN UNIT
INT
(Su ERC
ppli ON
ed NE
wit CTI
h D NG
CU CA
105 BL
E
)
14
AN
CA TEN
BL NA
E
EX
TE
NS
ION
13P
VIDEO INPUT
ANT
ENN
20P
15
N
IO p)
CT ca
NE ove
13
N
m
CO t re
LE
NO o no
AB
C
D
(
R
TO 3)
C
8
E 0
NN H3
CO ith C
ER d w
W
e
i
PO uppl
(S
13P
AP
17
LUG
INTERCONNECTING
CABLE
(Supplied with DCU105)
G
TIN
05)
NEC
ON
CU1
C
D
R
h
E
it
INT ABLE lied w
C Supp
(
VIDEO
INPUT
L
A
GN
TION E SI
NEC
K
CON BRA NAL
O
N
IG
ING E S
RK ERS
ite PA
EV
/Wh O
Red T n O R
E
Gree T
UT
Blue
-M
16
16P
18
2V
+1 ly)
RY pp
llow
TE nt su
Ye
T
e
BA ane
hit
TO erm Red
e/W
(P
ng
a
)
r
y
H O
pl
e
up
ITC
e
rs
hit
Blu
SW
we
e/W
HT
Po
(
G
I
Blu
AY
L
C
L
C
D
)
F
A
A n
RE
HE atio
TO
DO
NA
EA ly)
TOlumin
EN
N L upp
NT
(Il
A
O
S
R
RN IT (
WE
TU UN
H
PO y)
AC E
TO CH
TO uppl
A
E E AP
E
(S
AT ITH T
L
U W
INSIRE
W
D UT
DVUTP
O
9 INTERCONNECTING
CABLE
8 INTERCONNECTING
CABLE
ck
Bla
D
N
OU
TO
GR
OL
G R
RIN NT
EE CO
ST TE
TO MO
RE
258
wn
Bro
ack
/Bl
wn
Bro
4) AVX5000 + DCU105 + CH3083 + Power Amplifier (for 5.1ch system)
TO SIGNAL INPUT OF
AUXILIARY POWER AMPLIFIER
ck
Bla
INSULATE
EACH
WIRE WITH TAPE
DIGITAL OUT
(Do not remove cap)
E
BL
CA
G )
TIN 105
wn
C
o
U
r
E C
B
NN D
CO with
ER ied
V
INTuppl
12 )
Y + ply
(S
ER up
TT t s
BA anen
TO rm
llow (Pe
Ye
NO
TO GROUND
INTERCONNECTING CABLE
(Supplied with CH3083)
I
N
IO
CT
NE
N
CO
II
III
TO SIGNAL INPUT OF
AUXILIARY POWER AMPLIFIER
MICROPHONE
(Supplied with DCU105)
e
Blu
V
INTERCONNECTING CABLE
(Supplied with DCU105)
16P
DCU105
NAVI-VOICE SIGNAL(No connection)
DIGITAL INPUT
VIDEO OUTPUT
CH3083
2P
k
c
Bla
TO GROUND
XT
1 MAIN UNIT
13P
VIDEO INPUT
EN
SIO
N ANT
EN
NA
20P
15
N )
TIO ap
13
EC e c
NN mov
E
O
BL
C t re
CA
NO o no
R
O )
(D
T
3
EC 08
NN H3
CO ith C
ER d w
W
e
i
PO uppl
(S
VIII
13P
14
A
N
CA TEN
BL NA
E
E
PLU
G
VIDEO
INPUT
17
18
V
12 )
Y + ply
ER sup
llow
Ye
TT ent
A
B an
d
TO erm
e
Re
(P
hit
)
/W
ge
ply
p
ran
e
su
O
r
H
Blu
e
we
ITC
hit
Po
SW
e/W
C(
AY
T
C
L
H
Blu
A
RE
IG
L
TO
A
N
OF
AD n)
EN
AD
HE atio
NT
LE ply)
TOlumin
RA
ON(Sup
E
(Il
N
W
R IT
H
PO y)
TU UN
AC E
TO uppl
TO CH
E E AP
(S
EA
AT ITH T
L
U W
INSIRE
W
INTERCONNECTING
CABLE
(Supplied with DCU105)
G
TIN
NEC
ON
)
tely
ERC
INT ABLE separa
C Sold
(
IX
X
XI
L
NA
IG
ES
L
AK
BR IGNA
G
S
KIN SE
ite PAR VER
/Wh
Red TOn
RE
O
E
Gree T
UT
Blue
-M
ION
ECT
ONN
C
NO
16
16P
VI
VII
12P
13P
INT
(Su ERC
ppli ON
ed NE
wit CTI
h D NG
CU CA
105 BL
E
)
IV
XII
D UT
DVUTP
O
XIII
9 INTERCONNECTING
CABLE
XIV
8 INTERCONNECTING
CABLE
XVI
ck
Bla
ND
OU
GR
n
w
Bro
L
G RO
RIN NT
EE CO
ST TE
TO MO
RE
TO
XV
/B
wn
Bro
k
lac
XVII
XVIII
XIX
XX
259
260
CUSTOMER NOTICE
Please retain this booklet and write in the serial number
of your AVX5000 for identification.
The serial number is labeled or stamped on the chassis.
Serial No.
FUJITSU TEN LIMITED
Contact:FUJITSU TEN CORP. OF AMERICA
19600 So. Vermont Avenue, Torrance, CA 90502
Call:800-233-ECLIPSE
www.eclipse-web.com
"ECLIPSE" is a registered trademark of
FUJITSU TEN LIMITED in 50 countries.
090001-14770700 0508C (F.O)
Download PDF