Dalsa | Dalstar DS-42-01M60 | Product manual | Dalsa Dalstar DS-42-01M60 Product manual

Camera Fiber-Link
Product Manual
Part Number MAN-000004
Rev. J - March 2006
Logical Solutions Inc.
100 Washington Street
Milford, Connecticut 06460 U.S.A.
Telephone (203) 647-8700
Fax (203) 783-9949
www.thinklogical.com
Copyright Notice
Copyright © 2006 All Rights Reserved. Printed in the U.S.A.
Thinklogical
100 Washington Street
Milford, Connecticut 06460 U.S.A.
Telephone (203) 647-8700
All trademarks and service marks are property of their respective owners.
Document ID: MAN-000004
Subject: Camera Fiber-Link Digital Video Extension System
Revision: Rev. J, March 2006. 38 pages in total.
Camera Fiber-Link
Page 2
www.thinklogical.com
Table of Contents
1Introduction5
2
3
1.1
Camera Fiber-Link - - - - - - - - - - - - - - - - - - - - - - - 5
1.2
LASER Protection- - - - - - - - - - - - - - - - - - - - - - - - 6
1.3
System Features - - - - - - - - - - - - - - - - - - - - - - - - 7
1.4
Technical Specifications - - - - - - - - - - - - - - - - - - - - 8
Installation - - - - - - - - - - - - - - - - - - - - - - - 10
2.1
Intended Application - - - - - - - - - - - - - - - - - - - - - - 10
2.2
Small Form Factor - - - - - - - - - - - - - - - - - - - - - - - 11
2.3
Order of Installation Events- - - - - - - - - - - - - - - - - - - 12
2.4
Connecting the Camera Fiber-Link system - - - - - - - - - - - 13
2.4.1
Fiber Cable - - - - - - - - - - - - - - - - - - - - - - - - - - 13
2.4.2
Digital Video Camera Side - - - - - - - - - - - - - - - - - - - 14
2.4.3
Digital Video Frame Grabber Side - - - - - - - - - - - - - - - 14
2.4.4
Serial Port - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
2.4.5
AC Power - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
Regulatory & Safety - - - - - - - - - - - - - - - - - - 17
3.1
3.1.1
Safety Requirements - - - - - - - - - - - - - - - - - - - - - - 17
Symbols found on the Product - - - - - - - - - - - - - - - - - 17
3.1.1.1 Class 1M LASER Labeling - - - - - - - - - - - - - - - - - - 17
tel (203) 647-8700
3.1.2
Product Serial Number - - - - - - - - - - - - - - - - - - - - - 17
3.1.3
Connection to the Product - - - - - - - - - - - - - - - - - - - 18
Page 3
MAN-000004
4
3.2
Regulatory Compliance - - - - - - - - - - - - - - - - - - - - - 18
3.3
North America - - - - - - - - - - - - - - - - - - - - - - - - - 18
3.4
Australia & New Zealand - - - - - - - - - - - - - - - - - - - - 18
3.5
European Union- - - - - - - - - - - - - - - - - - - - - - - - - 19
3.5.1
Declaration of Conformity - - - - - - - - - - - - - - - - - - - 19
3.5.2
Standards With Which the Products Comply - - - - - - - - - - 19
3.5.3
Supplementary Information - - - - - - - - - - - - - - - - - - - 20
How to Contact Us - - - - - - - - - - - - - - - - - - - 21
4.1
Website - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21
4.1.2
E-mail - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
4.1.3
Telephone - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
4.1.4
4.2
Camera Fiber-Link
Customer Support - - - - - - - - - - - - - - - - - - - - - - - 21
4.1.1
Fax - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Product Support - - - - - - - - - - - - - - - - - - - - - - - - 22
4.2.1
Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
4.2.2
Return Authorization - - - - - - - - - - - - - - - - - - - - - - 23
4.2.3
Our Address - - - - - - - - - - - - - - - - - - - - - - - - - - 23
5
How to Order - - - - - - - - - - - - - - - - - - - - - - 24
A
Camera and Frame Grabber Compatibility Chart - - - 26
B
Camera Fiber-Link Mounting Template - - - - - - - - 30
C
Adapter Pinouts - - - - - - - - - - - - - - - - - - - - 31
D
Fiber Types vs. Distances - - - - - - - - - - - - - - - 34
E
Fiber Optic Ordering Information - - - - - - - - - - - 36
Page 4
www.thinklogical.com
Camera Fiber-Link
1
Introduction
Introducing the Thinklogical Camera Fiber-Link System
1.1 Camera Fiber-Link
The Thinklogical. Camera Fiber-Link is a Camera-Link extension system. The
Camera Fiber-Link system consists of a pair of components that are interconnected
using a duplex multimode fiber optic cable, allowing Camera Link video support up
to 1000 meters (3280 feet)* from the host computer. Each pair consists of a Camera
side unit and a Frame Grabber side unit (both units are similar in appearance, but
are labeled differently).
Note
*1000 meters (3280 feet) is the standard maximum distance for a fiber
type of 50/125, 1000Mhz-km. See Section Appendix D, Fiber Types vs.
Distances, on page 34 for maximum distances of other fiber types.
tel (203) 647-8700
Page 5
MAN-000004
Figure 1.1 Thinklogical Camera Fiber-Link Unit shown
1.2 LASER Protection
The Camera Fiber-Link system is designed and identified as a Class 1M LASER
product.
In order to avoid possible exposure to laser energy, it is good practice to attach
the fiber optic cables prior to applying power to the Camera Fiber-Link. If the fiber
optic cable should become disconnected, DO NOT attempt to look into the cable
or the panel mounted connector.
Camera Fiber-Link
Page 6
www.thinklogical.com
System Features
1.3 System Features
The Camera Fiber-Link systems are designed for high-resolution camera extension applications. The ability to remotely locate the CPU away from the camera
allows more control of your computer environment. It is possible to position the
camera in any setting while keeping the computer secure in a remote, controlled location.
Each Camera Fiber-Link system includes the following features:
•
•
•
•
•
•
•
•
•
•
tel (203) 647-8700
Supports the Camera Link base/medium/full1000 meters (3280 feet)
configuration
Extends digital video signals up to 1000 meters (3280 feet)
Serial Port (RJ45) with RS232 Interface provided
Transparent operation and functionality - no user interaction
required
Signal transmission via fiber optic cable - no RF interference
Uses duplex multi-mode fiber for base configuration, 50 or 62.5
micron, with SC-type connectors
Uses triplex multi-mode fiber for medium/full configurations, 50 or
62.5 micron, with SC-type connectors
Units are self-contained and do not require user adjustments
Two 2 Meter Camera-Link cables provided
(Part Number: CBL-000007-002M)
Two universal AC power adapters provided
(Part Number: PWR-000022)
Page 7
MAN-000004
Introduction
1.4 Technical Specifications
Each Thinklogical Camera Fiber-Link system is designed to the following specifications:
Supplied Cables
(1) KIT-000013 CAMERALINK W/RJ45 ADAPTER/CABLE KIT
Which contains the following:
(1) ADP-000007 DB9M TO RJ45F ADAPTER
(1) ADP-000008 DB9F TO RJ45F ADAPTER
(2) CBL-000001-002M CAT5 CABLE ASSEMBLY, 2 METERS
(2 for Base Units/4 for Medium/Full Units) CBL-000007-002M MDR-26
MALE TO MDR-26 MALE CABLES, 2 METERS
For Adapter Pinouts, please see Section Appendix C, Adapter Pinouts, on
page 31
Connectors
Frame Grabber side:
Camera Link MDR-26 female video input (2)
Dual SC-type fiber connector (1)
2.5mm power connector (AC adapter provided and required)
Serial Port - RJ45 connector (1)
Camera side:
Camera Link MDR-26 female video output (1)
Dual SC-type fiber connector (1)
2.5mm power connector (AC adapter provided and required)
Serial Port - RJ45 connector (1)
Note
The Camera Fiber-Link is available with Dual ST- or LCtype fiber connectors upon request.
Protocol
Camera Link compliant (supports base/medium/full configurations)
Indicators
Two LEDs on each Camera Fiber-Link module:
Loss of Signal [LOS] (red ON when no signal)
Power (green ON when power is applied)
Optical Cable
Duplex Fiber, multi-mode, 50 micron or 62.5 micron, SC-type connectors
(Fiber Cable is either customer-supplied or can be ordered from
Thinklogical; See Section Appendix E, Fiber Optic Ordering Information, on
page 36 for Fiber Cable Ordering Information.)
Camera Fiber-Link
Page 8
www.thinklogical.com
Technical Specifications
Operating Temperature
and Humidity
0 to 50 °C (32 to 122 °F), 5 to 95% RH, non-condensing
Housing Dimensions
Approx. 7 in x 5 1/2 in x 1-1/4 in high
(177.8 mm x 139.7mm x 31.75mm high)
Wall-mount keyhole slot spacing: 5 inches x 5 1/2 inches
Supply Voltage
+5.0 VDC. Adapter has Universal AC Power Input
Polarity: Positive Tip
DC Current
Camera Side: 1.25A, typical; Frame Grabber Side: 1.3A, typical
AC to DC Adapter
Input: 100-240VAC, 47-63 Hz, 0.8 Amperes
Output: +5VDC @ 5Amperes, 2.5mm barrel plug
Logical P/N: PWR-000022; two included with each Camera Fiber-Link pair
LASER Output
Specifications
Wavelengths are 778, 800, 825, and 850 nanometers
Maximum Laser power output in the fiber is 1.6mW
tel (203) 647-8700
Page 9
MAN-000004
2
Installation
2.1 Intended Application
The Camera Fiber-Link from Thinklogical permits the placement of a digital
camera up to 1000 meters (3280 feet) away from the controlling computer without
loss of resolution. Traditional copper cables are limited to 10 meters (32.81 feet) in
such applications. Each Base or Medium/Full Camera Fiber-Link system consists of
a pair of electronic units connected by a duplex multi-mode fiber optic cable. The
duplex fiber must be of equal length. The Medium/Full system pair, in addition
to the duplex fiber, also is connected by a simplex multi-mode fiber optic cable.The
Frame Grabber unit connects to the computer with a 2 meter Camera Link MDR26 male-to-male cable and the Camera unit connects to the digital camera.
Caution
The Camera Fiber-Link is a Class 1M LASER product that emits near
infrared light.
Note
The fiber optic cables should be attached to the Camera Fiber-Link
prior to powering up the units.
Note
It is necessary for the duplex multi-mode fiber to be of equal length.
Camera Fiber-Link
Page 10
www.thinklogical.com
Small Form Factor
2.2 Small Form Factor
Each Camera Fiber-Link module is wall-mountable, if desired. Mounting centers
are provided with keyhole slots (Fiber cable and power connector up, MDR-26 connector and RJ45 connector down). A mounting template is provided at the end of
this manual (Appendix B) for your convenience.
Figure 2.1 Camera Fiber-Link Application diagram
tel (203) 647-8700
Page 11
MAN-000004
2.3 Order of Installation Events
Note
It is recommended to test the camera and frame grabber prior to
installing the Camera Fiber-Link Extenders to verify their operation.
In order to properly use the Camera Fiber-Link system, you must follow this
order of events for the initial power-up.
1.
Install and connect your Fiber Optic Cable between the Camera side and the
Frame Grabber side modules.
Note
Be sure Fiber Optic Cable is positioned as below. The red LED,
located on the fiber side of the unit, will blink if system is talking and
Camera is not connected; it will be solid red if fiber is not connected.i
Camera Fiber-Link
Page 12
www.thinklogical.com
Connecting the Camera Fiber-Link
2.
Connect the AC Power Adapters (PWR-000022) to both units, and plug them into
a suitable power source.
3.
Using CBL-000007-002M (MDR-26 Male to MDR-26 Male Cable), connect your
camera to the Camera side unit, and turn on the camera.
4.
Using CBL-000007-002M (MDR-26 Male to MDR-26 Male Cable), connect your
frame grabber to the Frame Grabber side unit.
5.
If using an external sensor, external lighting, etc, use CBL-000001-002M (CAT5
Cable) to connect your serial device to the Serial Port on the Camera Side and
Frame Grabber unit.
6.
Start your application software.
2.4 Connecting the Camera Fiber-Link system
All physical connections to the product use industry-standard connectors.
2.4.1 Fiber Cable
A duplex fiber optic cable (for Base version) or a duplex and a simplex fiber optic
cable (for Medium/Full version) must be run between the location of the Frame
Grabber unit (near your CPU) and the Camera side unit (near the camera). The standard duplex multi-mode fiber cable must be 50 or 62.5 micron, terminated with an
SC-type connector and no longer than 3280 running feet (1000 meters)*. Be careful
to not kink or pinch the fiber cable as it is being installed, and keep all bend radii
to no less than 3 inches (76.2mm).
Connect your fiber cable to the SC-type connector on each Camera Fiber-Link
pair (one Camera side and one Frame Grabber side). Dress the cable so it will not
get crushed, pinched or otherwise damaged.
Note
It is necessary for the duplex multi-mode fiber to be of equal length.
Note
The Camera Fiber-Link is available with ST- or LC-type fiber
connectors upon request.
tel (203) 647-8700
Page 13
MAN-000004
Note
*1000 meters (3280 feet) is the standard maximum distance for a fiber
type of 50/125, 1000Mhz-km. See Appendix D for maximum
distances of other fiber types.
2.4.2 Digital Video Camera Side
The Camera side unit connects to your video camera using a MDR-26 male-tomale cable (CBL-000007-002M) which is supplied with the system. The Base version
includes 1 cable and the Medium/Full version includes 2 cables.
2.4.3 Digital Video Frame Grabber Side
The Frame Grabber side unit connects to your controlling computers Frame
Grabber with an MDR-26 male-to-male cable (CBL-000007-002M) which is supplied
with the system. The Base version includes 1 cable and the Medium/Full version
includes 2 cables.
2.4.4 Serial Port
Both the Camera side unit and the Frame Grabber side unit have a serial port
(RJ45 connector). This RS232 interface connects to your external sensor, external
lighting, etc., if needed, using a CAT5 Cable Assembly (CBL-000001-002M which is
supplied with the system).
The pinouts of the Serial Port (RJ45 connector) are as follows:
Camera Fiber-Link
Page 14
www.thinklogical.com
Connecting the Camera Fiber-Link
2.4.5 AC Power
Separate wall-pack AC-to-DC converters (Part Number PWR-000022) are
included. A power jack is provided on both units and accepts the +5VDC input. The
green power LED will light when the unit is receiving power.
tel (203) 647-8700
Page 15
MAN-000004
The DC power plug has a right-angle connector design.
The AC wall pack has a universal power rating (100-240VAC, 50-60 Hz), and also
has slip-on receptacle ‘fingers’ for various AC power receptacles found throughout
the world. Use the appropriate AC power ‘fingers’ for your country / location. The
others are not needed.
Figure 2.2 AC Power receptacle ‘fingers’ included with each power supply.
Camera Fiber-Link
Page 16
www.thinklogical.com
Safety Requirements
3
Regulatory & Safety
Regulatory and Safety approval is pending at this time.
3.1 Safety Requirements
3.1.1 Symbols found on the Product
Markings and labels on the product follow industry-standard conventions. Regulatory markings found on the products comply with requirements.
3.1.1.1 Class 1M LASER Labeling
3.1.2 Product Serial Number
The Camera Fiber-Link products have a unique serial number, imprinted on a
small silver label that is placed on the bottom of the chassis. The serial number
includes a day-code. The format for the day-code is 2-digits each for the month, the
day and four digits for the year, and two or three digits for a unique unit number.
This serial number is also found on the original shipping carton.
tel (203) 647-8700
Page 17
MAN-000004
3.1.3 Connection to the Product
Connections and installation hardware for the product use industry-standard
devices and methods. All wiring connections to the customer equipment is done in
a fashion to minimize proprietary or customized connectors or cabling. Power connections are made with regionally appropriate power cords and approved methods.
3.2 Regulatory Compliance
The Thinklogical. Camera Fiber-Link products are designed and made in the
U.S.A. The Camera Fiber-Link products have been tested by a nationally recognized
testing laboratory and found to be compliant with the following standards (both
domestic USA and many international locations).
3.3 North America
These products comply with the following standards:
Safety
•
UL60950 : 2000
•
CAN/CSA C22.2 No. 60950-00
LASER Safety
•
CDRH 21CFR 1040.10
•
Class 1M LASER Product
•
Accession Number 0322261
Electromagnetic Interference
•
FCC CFR47, Part 15, Class A
•
Industry Canada ICES-003 Issue 2, Revision 1
3.4 Australia & New Zealand
This is a Class A product. In a domestic environment this product may cause
radio interference, in which case the user may be required to take adequate measures.
Camera Fiber-Link
Page 18
www.thinklogical.com
European Union
3.5 European Union
3.5.1 Declaration of Conformity
Manufacturer’s Name & Address
Thinklogical.
100 Washington Street
Milford, Connecticut 06460 USA
Telephone (203) 647-8700
Product Name
•
Model: Camera Fiber-Link Video Extension System
These products comply with the requirements of the Low Voltage
Directive 72/23/EEC and the EMC Directive 89/336/EEC.
3.5.2 Standards With Which the Products Comply
Safety
•
IEC60950:1992+A1, A2, A3, A4, A11
LASER Safety
•
IEC60825:2001 Parts 1 and 2
•
Class 1M LASER Product
Electromagnetic Emissions
•
EN55022: 1994 (IEC/CSPIR22: 1993)
•
EN61000-3-2/A14: 2000
•
EN61000-3-3: 1994
Electromagnetic Immunity
tel (203) 647-8700
•
EN55024: 1998 Information Technology Equipment-Immunity Characteristics
•
EN61000-4-2: 1995 Electro-Static Discharge Test
•
EN61000-4-3: 1996 Radiated Immunity Field Test
•
EN61000-4-4: 1995 Electrical Fast Transient Test
•
EN61000-4-5: 1995 Power Supply Surge Test
•
EN61000-4-6: 1996 Conducted Immunity Test
•
EN61000-4-8: 1993 Magnetic Field Test
•
EN61000-4-11: 1994 Voltage Dips & Interrupts Test
Page 19
MAN-000004
3.5.3 Supplementary Information
The following statements may be appropriate for certain geographical regions
and might not apply to your location.
Note
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Note
This Class A digital apparatus complies with Canadian ICES-003 and
has been verified as being compliant within the Class A limits of the
FCC Radio Frequency Device Rules (FCC Title 47, Part 15, Subpart
B CLASS A), measured to CISPR 22: 1993 limits and methods of
measurement of Radio Disturbance Characteristics of Information
Technology Equipment.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigencies du Règlement
sur le matérial brouilleur du Canada.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may
be required to take adequate measures.
Camera Fiber-Link
Page 20
www.thinklogical.com
4
How to Contact Us
4.1 Customer Support
Thank You to our Customers for choosing a Thinklogical product for your application. We appreciate your business and are interested in helping you successfully
use our products.
Logical is here to help you. To contact Thinklogical, use the following telephone
numbers and internet-based methods.
4.1.1 Website
Check out our website for current product offerings, support information, and
general information about all of the Thinklogical we offer.
Our internet website offers product information on all current systems, including technical specification sheets and installation guides (for viewing on-line or for
download), product diagrams showing physical connections, and other information
you might need. We are constantly updating our website, so be sure to “refresh” your
browser when visiting the Thinklogical website to see the most up-to-date information.
Internet: www.thinklogical.com
Note
Most online documents are stored as Adobe Acrobat “PDF” files. If
you do not have the Adobe Acrobat Reader needed to view PDF files,
visit www.adobe.com for this free download.
tel (203) 647-8700
Page 21
MAN-000004
4.1.2 E-mail
Thinklogical is staffed Monday through Friday from 8:30AM to 5:30PM, Eastern
Time Zone. We will try to respond to your email inquiries promptly, using the following email addresses for your different needs:
info@thinklogical.com -- Information on Thinklogical and our products
sales@thinklogical.com -- Sales Department - orders, questions or issues
support@thinklogical.com -- Product support, technical issues or questions,
product repairs, requests for Return Authorization, any other issue.
4.1.3 Telephone
Telephone Sales: Contact our expert technically-oriented Sales staff via telephone in Milford, Connecticut, at (203) 647-8700 or if in the continental US, you
may use our toll-free number (800) 291-3211. We’re here Monday through Friday,
8:30AM to 5:30PM, Eastern Time Zone. Ask for their direct dial phone number
when you call!
Telephone Product Support: Contact Product Support via telephone in Milford, Connecticut, at (203) 647-8700. The support lines are manned Monday
through Friday, 9AM to 5PM, Eastern Time Zone.
International Sales: Please contact our US Sales staff in Milford, Connecticut,
at (203) 647-8700. We’re here Monday through Friday, 8:30AM to 5:30PM, Eastern
Time Zone (same as New York City). If leaving a voice message, please provide a ‘best
time to call back’ so we may reach you at your convenience.
Our switchboard attendant will direct your call during regular business hours.
We have an automated attendant answering our main telephone switchboard after
regular business hours and holidays. You can leave voice messages for individuals at
any time. Our Sales Representatives have direct numbers to speed up your next call
to us.
4.1.4 Fax
Our company facsimile number is (203) 783-9949. Please indicate the nature of
the fax on your cover sheet, and provide return contact information.
4.2 Product Support
Thinklogical.’s support personnel are available Monday through Friday from
8:30AM to 5:30PM, Eastern Time Zone.
Camera Fiber-Link
Page 22
www.thinklogical.com
If your application might require assistance at some time outside of our normal
business hours, please contact us beforehand and we will do our best to make
arrangements to help you with your Thinklogical products.
4.2.1 Warranty
Thinklogical.’s products carry a one year warranty, with longer-term warranties
available at time of purchase on most products. Please refer to your product invoice
for your product’s Warranty Terms and Conditions.
For specific details about the product warranties, please contact Sales.
4.2.2 Return Authorization
If, for some reason, you need to return your Thinklogical product to us, please
get a Return Authorization Number (RA# or RMA#) from Logical’s Product Support department before sending the unit in. Return Authorization must include contact information (phone preferred) in the event we have any questions.
After receiving your RA Number, please ship the unit postpaid, with the RA#
prominently displayed on the shipping container.
We will contact you about your product once we determine its status.
Products received without Return Authorization and/or Contact information
may require additional attention on our part that may delay any desired service or
support with your system.
4.2.3 Our Address
If you have any issue with the product, have product questions, or need technical
assistance with your Camera Fiber-Link system, please call us (203) 647-8700 and let
us help.
If shipping something with an RA#, or if you’d like to write us, we are located at:
Thinklogical.
Attn: RMA Department
100 Washington Street
Milford, CT 06460 USA
tel (203) 647-8700
Page 23
MAN-000004
How to Order
5
How to Order
Camera Link Tansmitters and Receivers with Serial (RJ45) HIGH SPEED BASE
CFL-000003-ST
CFL-000003-SC
CFL-000002-LC
CFL-000003-TXST
CFL-000003-TXSC
CFL-000003-TXLC
CFL-000003-RXST
CFL-000003-RXSC
CFL-000003-RXLC
Camera Fiber-Link TX and RX pair, serial support RJ45, dual fiber, ST
Camera Fiber-Link TX and RX pair, serial support RJ45, dual fiber, SC
Camera Fiber-Link TX and RX pair, serial support RJ45, dual fiber, LC
Camera Fiber-Link Transmitter/Camera Side, serial RJ45, dual fiber, ST
Camera Fiber-Link Transmitter/Camera Side, serial RJ45, dual fiber, SC
Camera Fiber-Link Transmitter/Camera Side, serial RJ45, dual fiber, LC
Camera Fiber-Link Receiver / Frame Side, serial RJ45, dual fiber, ST
Camera Fiber-Link Receiver / Frame Side, serial RJ45, dual fiber, SC
Camera Fiber-Link Receiver / Frame Side, serial RJ45, dual fiber, LC
Camera Link TX and RX with Serial (RJ45) HIGH SPEED BASE/MEDIUM&FULL
CFL-000004-ST
CFL-000004-SC
CFL-000004-LC
CFL-000004-TXST
CFL-000004-TXSC
CFL-000004-TXLC
CFL-000004-RXST
CFL-000004-RXSC
CFL-000004-RXLC
Camera Fiber-Link
Camera Fiber-Link TX and RX pair, serial support RJ45, Triple fiber, ST
Camera Fiber-Link TX and RX pair, serial support RJ45, Triple fiber, SC
Camera Fiber-Link TX and RX pair, serial support RJ45, Triple fiber, LC
Camera Fiber-Link Transmitter/Camera Side, serial RJ45, Triple fiber, ST
Camera Fiber-Link Transmitter/Camera Side, serial RJ45, Triple fiber, SC
Camera Fiber-Link Transmitter/Camera Side, serial RJ45, Triple fiber, LC
Camera Fiber-Link Receiver / Frame Side, serial RJ45, Triple fiber, ST
Camera Fiber-Link Receiver / Frame Side, serial RJ45, Triple fiber, SC
Camera Fiber-Link Receiver / Frame Side, serial RJ45, Triple fiber, LC
Page 24
www.thinklogical.com
Product Support
Camera Link Cables and Connectors
CBL-000007-002M
PWR-000022
ADP-000007
ADP-000008
MDR-26 Camera-Link cable (2 Included CFL-3,CFL-4 ( 4 Included)
Power supply, 5 volt Universal Adapter, replacement part for CFL-3 & CFL-4
DB9M to RJ45F Adapter for SCS (1 Included)
DB9F to RJ45F Adapter for SCS (1 Included)
The CFL-000003 consists of two power supplies, two 2 meter cables, one transmitter and one receiver.
The CFL-000004 consists of two power supplies, four 2 meter cables, one transmitter and one receiver.
tel (203) 647-8700
Page 25
MAN-000004
Appendix A Camera and Frame Grabber
Compatibility Chart
Tested Frame Grabbers
Manufacturer
Model
Active Silicon
Phoenix PHX-D48CL
Bitflow
R3-CL
Bitflow
R3-PCI-CL13
Bitflow
R3-PCI-CL23
Bitflow
R64=PCI-CL-F
DALSA-Coreco
PC-Camlink
DALSA-Coreco
X64-CL iPro
DALSA-Coreco
X64-CL Dual
Datacube
MaxRevolution V2-1000 Full
Euresys
Grablink Value
Imperx
FrameLink
Matrox
Meteor II CL
Matrox
Helios XCL
Mikrontron
INSPECTRA-4C
Mikrontron
INSPECTRA-5
National Instruments
NI 1428 CL
National Instruments
NI 1426 CL
National Instruments
NI 1429 CL
Camera Fiber-Link
Page 26
www.thinklogical.com
Cameras and Frame Grabbers Tested
with Thinklogical Camera-Link Extender
Tested Cameras up to Full Configuration
Manufacturer Model
Bits/pixel
Taps
Adimec
Adimec
Adimec
Adimec
Adimec
Adimec
Adimec
Adimec
Adimec
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Atmel
Basler
Basler
Basler
Basler
Basler
Basler
Cohu
Cohu
Cohu
tel (203) 647-8700
A1000m/S or m/D
A1600m/S or m/D
A2000m/S or m/D
A4000m/S or m/D
A4020m/S or m/D
A1000c/S or c/D
A1600c/S or c/D
A2000c/S or c/D
A4020c/S or c/D
AVIIVA C2 CL 4010
AVIIVA SC2 CL 4010
AViiVA M2 CL 0514
AViiVA M2 CL 201x
AViiVA M2 CL 4010
AViiVA SM2 CL 0514
AViiVA SM2 CL 201x
AVIIVA SC2 CL 4010
AViiVA M4 CL 2014
AViiVA M4 CL 6007
AViiVA M4 CL 8007
CAMELIA 8M C1
CAMELIA 8M M1
ATMOS 1M60
ATMOS 1M30
L103k
L301KC/F
A202K
A404K
A501k
A504KC
7700
7800
7900
Page 27
8 or 10
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
8 or 12
8/10 or 12
8/10 or 12
8/10 or 12
8/10 or 12
8/10 or 12
8/10 or 12
8/10 or 12
8 or 12
8 or 12
8 or 12
8/10 or 12
8/10 or 12
8/10 or 12
8/10 or 12
8 or 10
8 or 10
10
8 or 10
8
8
10
8
8 or 10
/S:1, /D:2
/S:1, /D:2
/S : 1, /D : 2
/S : 1, /D : 2
/S : 1, /D : 2
/S : 1, /D : 2
/S : 1, /D : 2
/S : 1, /D : 2
/S : 1, /D : 2
2
2
2
2
2
2
2
2
2
4
4
1
1
2
2
2
1
2
8
1
10
1
1
1
Clock (Mhz)
40
40
40
40
40
40
40
40
40
60
60
60
60
60
60
60
60
60/120
80/160
80/160
25
25
75
37.5
20 per tap
60
40
50
50
67
40
40
20
MAN-000004
Cameras and Frame Grabbers Tested
with Thinklogical Camera-Link Extender
Tested Cameras up to Full Configuration
Manufacturer Model
Bits/pixel
Taps
Dalsa
Dalsa
Dalsa
Dalsa
Dalsa
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
Imperx
JAI
JAI
MIKROTRON
MIKROTRON
Photonfocus
Pulnix
Pulnix
Pulnix
Pulnix
Pulnix
Camera Fiber-Link
Dalstar DS-21-02M30
Dalstar DS-22-2M30
1m28
Piranha2 P2-2X
P2-42-06K40
IPX-VGA90
IPX-VGA120
IPX-VGA210
IPX-1M48
IPX-2M30
IPX-2M30H
IPX-4M15
IPX-11M5
MDC-1004
MDC-1600
MDC-1920
MDC-2048
MDC-4000
CV-M7+CL
CV-M4+CL
MC1302/03
MC1310/11
MV-D1024-160-CL-8
TMC-1000-CL
TMC-1400-CL
TMC-4000-CL
TMC-4100CL
TM6710CL
Page 28
8 or 10
8 or 10
10
8 or 10
8
8 or 10
8 or 10
8 or 10
8 or 10
8 or 10
8 or 10
8 or 10
8 or 10
12
12
12
12
12
10
10
8 or 10
8
8
24bit RGB
8
8
10
8
2
2
1
2
4
1
1
2
2
2
2
2
2
2
2
2
2
2
1
1
2
8
2
3
1
2
2
2
Clock (Mhz)
40 per tap
40 per tap
28
40 per tap
40
40
40
40
40
40
40
40
28
40
40
40
40
28
40.49
40.49
66
85
80
20
50
40 per tap
40
25.49
www.thinklogical.com
Cameras and Frame Grabbers Tested
with Thinklogical Camera-Link Extender
Tested Cameras up to Full Configuration
Manufacturer Model
Bits/pixel
Taps
Clock (Mhz)
Redlake
Redlake
Redlake
Redlake
Redlake
Redlake
Redlake
Silicon Imaging
MegaPlus II ES 11000
ES 2020
ES 1603
ES 4020
ES 3200
ES 1100
ES 2001
SI-1280
24bit RGB
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
8,10 or 12
12
3
2-Jan
1
2-Jan
1
2-Jan
2-Jan
1
25
30/38
12-Oct
30/38
12-Oct
30/38
30/38
40
Sony
Sony
Sony
Sony
SVS-Vistek
Toshiba
XCL-U1000
XCL-U1000C
XCL-V500
XCL-X700
SVS 085CFCL
1K-SX1
10
24bit RGB
10
10
10
8
1
1
1
1
1
1
36
36
24.5
29.5
43
28.634
tel (203) 647-8700
Page 29
MAN-000004
Appendix B Camera Fiber-Link Mounting
Template
Use appropriate fasteners and anchors of your choosing to mount each unit.
Note
Leave clearance (3 inch bend radius) for your Fiber Cable at top
Camera Fiber-Link
Page 30
www.thinklogical.com
Appendix C Adapter Pinouts
The following pages show the pinouts for the listed adapters:
ADP-000007
ADP-000008
tel (203) 647-8700
Page 31
MAN-000004
Page 32
Page 33
Appendix D Fiber Types vs. Distances
Camera Link Extender
Distance from camera to host computer
<Tested Full Configuration>
Fiber Type:50/125,400Mhz-km
Max Dist(m) Max Dist(f)
500
1,640
Fiber Type:50/125, 1000Mhz-km
Max Dist(m) Max Dist(f)
1000
3,280
Fiber Type: 62.5/125um, 160Mhz-km
Max Dist(m) Max Dist(f)
220
720
Camera Fiber-Link
Page 34
www.thinklogical.com
Fiber Size
50/125
Numerical
Core
Clad
Typ.
Max.
Coat Diameter
Atten.
Diameter Diameter
Attenuation Attenuation
.200 +/-.015 50 +/-3
125 +/-2
62.5/125 .275 +/-.015 62.5 +/-3 125 +/-2
tel (203) 647-8700
500 +/-25
2.6/0.6
245/500 +/-25 2.7/.075
Page 35
3.5/1.2
3.75/1.2
MAN-000004
Appendix E Fiber Optic Ordering
Information
Fiber Optic Connectors:
•
figure 1
•
•
LC fiber connector
This is the connector type used to connect to the DCS series of matrix switches. The
small size and positive latching feature makes the LC the best choice for high density
connector panel applications. It is an optional connector choice on many Thinklogical
extenders.
•
figure 2
•
•
SC fiber connector
The SC is a stackable connector used for quick connect and disconnect applications. It is
available on many Thinklogical extenders as a no-charge option.
•
figure 3
•
•
ST fiber connector
The ST is a bayonet coupling style of connector. It has either a rugged plastic or metal
housing depending upon manufacturer. It is reliable and uses the same ferrule as the SC.
The ST is available on all Thinklogical extenders.
Camera Fiber-Link
Page 36
www.thinklogical.com
Fiber Optic Cable Assemblies:
Simplex Assemblies: Single fiber with either ST, SC or LC connectors at the ends. Both
ends terminated at the factory.
Duplex Assemblies: Two fibers with either ST, SC or LC connectors at the ends. All
ends terminated at the factory.
Plenum style assemblies are available. Please call for pricing.
Riser style Assemblies: Uses cable approved for use in non-air plenum applications.
Low smoke, zero halogen cable jackets are available. Please call for pricing.
Note: Patch cables are riser rated, however have a 2 mm diameter rather than 3 mm.
tel (203) 647-8700
Page 37
MAN-000004
tel (203) 647-8700
MAN-000004 - 38 pages
www.thinklogical.com
Download PDF