Mitsubishi | JT-SB216DS-W-AUS | Specifications | Mitsubishi JT-SB216DS-W-AUS Specifications

Mitsubishi Electric Hand Dryer
HAND DRYER
Safety Precautions
For Installers
For Users
Safety Precautions
● Read the manual thoroughly before beginning installation to ensure the appliance is installed safely and correctly.
● Local installation standards should be obeyed and installation should be performed by the dealer or a qualified
professional.
● Do not install in locations where salt damage may occur, or where corrosive, neutral, or reductive gases are
present.
● Do not scratch, damage, process, excessively bend, pull, twist or bundle the power cable, and do not place
heavy objects onto it or trap it.
● Do not attempt any disassembly or modification of the appliance that is not expressly stated in the manual.
● Do not use in a hot location such as a shower room, where condensation may form on the appliance, or where
water may splash directly onto the appliance.
● Electrical wiring work should be done by a certified professional in conformance with the technical standards for
the equipment or official standards.
● Use single-phase 220-240V power.
● Use exclusive wiring
● Be sure to install a ground-fault circuit interrupter.
● A means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
● Do not install when the product (power cable) is electrified.
● Install securely in a location strong enough to support the weight of the appliance.
● Wear gloves when installing the appliance.
Installation Precautions
Safety Precautions
● Read the manual thoroughly before use to ensure the appliance is used safely and correctly.
● Do not open the front panel
● Do not use at locations where salt damage may occur, or where corrosive, neutral, or reductive gases are
present.
● Do not use in a shower room or other locations with a great deal of humidity in the air, or where condensation
may form on the appliance.
● Do not allow water to get on the appliance.
● Do not modify or disassemble the appliance.
● When changing the installation place, consult your dealer or installer.
● Use single-phase 220-240V power.
● Use exclusive wiring
● Always turn off the power switch during maintenance work.
● This appliance is not intended for use by young children or infirm persons unless they are adequately supervised
by a responsible person to ensure that they can use the appliance safely.
● Young children should be supervised to ensure that they do not play with the appliance.
● Do not use for drying anything other than hands.
● Wear rubber gloves when cleaning the appliance.
● Always use the appliance with the drain tank, air filter, and side covers attached.
● If the appliance stops working or if a malfunction occurs, turn off the power switch and groundfault circuit
interrupter before contacting your dealer for an inspection and repairs.
●If the room temperature is above 30°C, the heater will stop working to prevent the temperature from rising too high.
If the room temperature is less than 18°C, the air may feel cold.
Caution
● Do not install in the following types of location.
1. Outdoors
2. Locations where the temperature could be lower than 0ºC.
3. Locations where there is a lot of dust.
4. Locations where the temperature could be higher than 40ºC.
5. Locations where there is a lot of condensation.
6. Locations where salt damage may occur.
7. Vehicles (including ships and airplanes)
8. Locations where the appliance is in direct or strong sunlight
9. Near food or tableware.
10. Locations where the appliance may come into direct contact with water.
11. Kitchens (Where there is a risk of water splashing.)
12. Locations where corrosive, neutral, or reductive gases are present.
13. Rooms that have a sterilization basin, swimming pools, bathrooms.
● Ensure a distance of at least 130mm from the floor. Failure to do so may result in dirt or water entering the
appliance, causing damage.
● Ensure there is at least 150mm on both sides of the appliance to allow for maintenance.
Note
● Do not use with chemicals on your hands.
● Be sure to completely wipe off any detergents or chemicals on the appliance.
● Only use the specified cleaning agents.
● If water is sucked into the appliance, it may cause damage to the mechanism, or moisture may be absorbed into
the soundproofing material, allowing bacteria to breed. Therefore, do not allow water to come in contact with the
air filter or air duct.
● Drying time (listed in the catalogue) will vary by individual user.
● Continuous operation in high-temperature environments (40°C) may cause overheating to be detected in
electronic components, with an error indication appearing.
This does not mean that the unit has malfunctioned, with the error sign automatically terminated when the
temperature declines.
●Do not use the product to dry any chemicals or similar substances from the hands; failure to observe this
precaution may shorten product life.
● Because the product is an electrical appliance, it should not be cleaned directly with pressurised water or by
similar means.
● Do not clean the front cover of a silver appliance with alcohol.
✽“Alcohol” means a disinfectant with an ethanol content of 83% or less.
● Do not use any of the following cleaning materials
• Solvents such as thinner or benzene • Acid, alkaline or chlorine detergents • Mold and mildew removers
• Citrus-based or other plant-based detergents • Nylon scourers or abrasives • Antiseptics
Damage to the appliance (such as rusting) is not covered by the warranty if the above cautions are not
observed.
● To clean the exterior of the main unit, remove any dust or grime using a damp cloth. If using a detergent, use
only a neutral detergent diluted with water. (pH: 6-8)
● After cleaning with neutral detergent or alcohol, be sure to wipe away all remaining traces of the detergent or
alcohol.
●Water collected in the tank and drain receptacle at the bottom of the main unit must be emptied regularly to
avoid overflow.
●Clean the air filter approximately once a week.
●Jet Towel service life is about 7 years, figured at 400 uses daily. Depending upon specific use conditions, this
period may be shortened. Please contact Mitsubishi Electric if daily use broadly exceeds the designed level. In
cases when the number of uses doubles the average frequency, for example, the unit's lifespan will be reduced
to one-half.
● Water drawn into the main unit may be absorbed by the soundproofing material, resulting in bacterial build-up.
To prevent this, ensure that water does not get in around the air filter and air intake.
✽Safety considerations require that the serial number and/or appropriate markings or labeling be visible. When purchasing the product, make sure they are displayed on the main unit.
●Certain ratings and specifications may change due to product improvements or modifications.
●While every effort has been made to represent product colours herein accurately, slight deviations from actual colour may be noted due to the printing process.
Mitsubishi Electric Corporation's Nakatsugawa Works is an ISO certified plant,
having obtained both ISO 9001 Quality Management System and ISO 14001
Environmental Management System certification.
M i t s ubi s hi E l e ctric Han d Dr yer web site
http://www.mitsubishielectric.com/bu/handdryer/
[MITSUBISHI ELECTRIC Regional Branch]
[Dealer]
The Original High-Speed Dryer
Over 20 Years of Innovation
For Europe/Oceania
L-175-1-C8853-C NK1310 Printed in Japan (DNP)
Revised publication effective Oct. 2013.
Superseding publication of L-175-1-C8853-B Feb. 2012.
Specifications are subject to change without notice.
http://www.mitsubishielectric.com/bu/handdryer/
Mitsubishi Electric
The pioneers of the modern hand dryer
For the Environment
For Corporate Management
No Waste Paper
Substantial Cost Reduction
The high-speed Jet Towel TM hand dryer uses jet
streams of air to dry hands, eliminating the paper
waste associated with the use of paper towels, and
thus relieving you of the trouble of waste disposal as
well. The preservation of forest resources will also
contribute to enhancing your corporate image.
The monthly expense is reduced to a fraction of the
cost in comparison to paper towels or rolled-cloth
towels. The higher the use, the greater the savings.
Visit the website below to run a cost simulation
No. of paper towels made from one tree
1 tree
(8m high, 14cm dia.)
Approx. 20,000
paper towels
(2-month supply for 1 dispenser:
2 towels each time, 200 times/day)
Example: Company A (10-story building)
■Paper towel used
■Paper towel used
Approx.
Approx. 13,000 sheets/day
320,000
sheets/month
http://www.mitsubishielectric.com/bu/handdryer/
Unit: ¥
Uses per day
100
uses
200
uses
300
uses
400
uses
Paper towels
5000
10000
15000
20000
Cloth-roll towels
7500
15000
22500
30000
196
376
557
738
130
246
361
476
127
239
351
463
JT-SB216JSH
Heater on
Heater off
JT-SB216KSN
= 64 bags
of waste/day!
(Assuming 200 paper
towels/bag)
Electricity cost
per month
Calculation conditions
*Used 25 days per month
Jet Towel:
Heater on for 10sec., off for 11sec. per use; Constantly on (1 day
=24hr; 1mo = 30d); Electricity cost of (¥) 21 yen/kWh
Paper towels:
Paper cost of (¥) 1 yen per sheet; 2 sheets per use
Cloth-roll towels: Rental fee of (¥) 600 yen per roll: 200 uses per roll
*Survey conducted by Mitsubishi Electric
✻Many paper towels are made from recycled paper,
so it does not necessarily lead to environmental destruction.
Since developing the world’s first jet towel in 1993, we have continued to improve technologies
and services focusing on ease of use for our customers.
1
1993
1993
1995
1997
1999
2001
2006
2011
JT-16A
JT-16B
JT-16C
JT-16C3
JT-116C4/C4K
JT-216CS4/CS4K
JT-SB116D
JT-SB216ESH
JT-SB216GSN
JT-SB216JSH
JT-SB216KSN
For Building Management
For Customers
Easy Maintenance
Improved Service
Appealing to building management companies too!
The only maintenance required is clean the air filter
Evaluated highly for its sanitary characteristics, the
Jet Towel T M is popular among facilities and shops
and removing water from the drain tank*. Save time by
eliminating the daily replenishment of paper towels,
alike. In addition to its abilit y to dr y hands complete l y in a mat te r of se c onds a nd of fe r a cle a n
disposal of paper waste and replacing rolled-cloth
towels.
sanitar y environment for customers, maintenance
and upkeep costs are minimized for maximum cost
efficiency. The result, enhanced customer service.
*Tank must also be cleaned.
2
Overflowing with Innovations Unique Only to Mitsubishi Electric…
Jet Towel Technologies
TM
Simple to Use
Hygienic
Eas y h a n d a c c e ss f r o m b o t h si d e s.
Bacteri al growth s uppres s ed for al l parts
s us cepti bl e to contact wi th water.
Independent air ducts ensure airflow is always fresh.
Independent Air Ducts
Antibacterial Treatment
Open-side Design
Repeat a few times
The dryer is open on both sides, enabling easy hand access from the side
without touching the unit. Inserting hands from the sides as shown in the
photo, and slowly raising and lowering them a few times maximizes drying
performance.
All parts susceptible to coming in contact with water, such as handdrying section, drain tank and water drainage duct (drain hose), are
subjected to antibacterial treatment to ensure highly sanitary conditions.
<Comparative Proof of Antibacterial Effect>
Anti-bacterial
treatment
Following 24hr culturing using film contact
method in Mitsubishi Electric laboratories.
In addition to an extremely hygienic
touch-free design, emphasis has also
been placed on ensuring the flow of
fresh-air. The air-intake port and airflow
route are isolated from the water drainage
d u c t i n M i t s u b i s h i E l e c t r i c p ro d u c t s .
Inserting the hands triggers a jet-stream
of fresh air without using any air in the
vicinity of the hands.
1
2
Insert hands from
the sides
3
Slowly raise
hands up
4
w/o antibacterial
treatment
And out
w/ antibacterial
treatment
Drainage tank
*Blue-shaded areas have
received antibacterial
treatment.
Repeat 1 to 4 a few times.
For smooth and reliable operation,
the dryer is equipped with upper and
lower sensors. Once hands are fully
inside, lower sensor detection starts
t h e a i r f l o w, a n d w h e n h a n d s a r e
removed completely, upper sensor
detection stops the dryer, preventing
water drops from blowing back up.
The New Slim Type is equipped with
a “Child Sensor*” further enhancing
operation ease.
Stop detection
Choi ce of operati on m odes accordi ng to us e
Air-speed and Heater Setting Switches Included
An alcohol-resistant resin is used, enabling
alcohol-based products to be used for cleaning the hand-drying section, drain tank and
water drainage duct where sanitary conditions
are a matter of concern. The open-side design,
which allows easy hand access from either
side, ensures quick and thorough cleaning of
the hand-drying section as well.
✻ “Alcohol“ means a
disinflectant containing
83% of ethanol or less.
S tabl e operati on for l ong s ervi ce l i f e.
Brushless DC Motor
400 uses daily
service life
Approx. 7 years
There is a choice of two airflow speeds:
“High” for prioritized drying and “Standard”
for low-noise operation.
The heater can be switched on or off.
Approx.
15°
ON
HIGH
ON
HEATER
*The setting switches are located inside the main
unit, and can only be set at the time of installation.
Start detection
Start detection sensor is located
in the lower side of the trough.
3
Comfortable Positioning
Development included studying a
hand insertion angle comfortable and
easy to use for a majority of people.
As the result, the front panel is gently
s l a n t e d o u t w a rd , c re a t i n g a e r g o nomic hand insertion angle of
approximately 15° that allow users to
stand comfortably and naturally
when inserting their hands into the
trough.
Silver ions attach to the cell walls of
general cellular bacteria, curbing protein
synthesis and reactions to control bacterial
growth and reproduction.
Alcohol-resistant Resin
Comfort
E a sy t o use in na t ur a l post ur e .
Upper and Lower Sensor Operation
Drain tank
Can be wi ped cl ean wi th al cohol .
Drainage water flow
H igh ly r e l i a b l e st a r t a n d s t o p .
Water drops
Air intake
duct
Bacteria accumulation
To the open-sides
Air ducts
AIR SPEED
OFF
STANDARD
1 2
Mode
Drying time ✻1
Operating noise ✻2
Power
consumption
HIGH
Approx. 9~11sec.
Approx. 61dB
1240W
STANDARD
Approx. 11~13sec.
Approx. 58dB
1070W
The motor is a key part of the Jet Towel T M . Accordingly, Mitsubishi
Electric has developed a durable, high-quality brushless DC motor
(Slim Series) designed for use 400 times a day for seven years.
Eliminating problems related to the wear-and-tear on motor brushes
ensures truly efficient power and stable operation for extended
periods of time.
■ Brushless DC Motor
Contact-free rotor
eliminates wear
and tear.
■ Commutator Motor
Wear generated
in brush and
rotor.
✻1
Drying times obtained using in-house measurement method.
✻2
JT-SB216JSH used with heater turned on and at factory default settings.
Measurements performed in an anechoic chamber at a distance of 2m.
4
Refined, Ergonomic Design Available in Three Attractive Colors
- Select the unit that best matches your sanitary needs
New Slim Series
Heater Type
Model JT-SB216JSH
(w/heater) 220-240V/50 • 60Hz (-W-NE Super White, -H-NE Dark Grey, -S-NE Silver)
Heater-less Type
Model JT-SB216KSN
(w/o heater) 220-240V/50 • 60Hz (-W-NE Super White)
Install multiple units neatly aligned with
sinks.
Prevent water from dripping onto the
floor for better impression of cleanliness.
Designed for Installation between Sinks
Can be aligned with the top of sink basins.
The ergonomic rectangular design matches well with most sink styles. Overall unit size was taken into consideration as well, ensuring
that the top of the unit can be neatly aligned with the top of the sink basin. To ease congestion and prevent water spillage, the installation of multiple units is recommended for places frequented by many people such as movie theaters and amusement facilities where
many may people use dryers at the same time.
Certified by
New colors for greater
flexibility in room coordination
Sliver: luxurious and chic
New
Color
NSF/ANSI 169
NSF International, an independent public safety health
and standards organization, has certified the Jet Towel
to be compliant with their rigorous requirements.
Super White
Grey
Silver
✻Counter table Installations or alignment with sink basin tops may result in an installation
height lower than that recommended.
Low Running
Costs
¥10/
210 uses
JT-SB216KSN
(without heater)
9~11sec
Designed
Quick Drying Antimicrobial for Alcohol
Airflow rate
✻2
✻1
106m/sec.
JT-SB216JSH
Airflow
Drain tank
Quiet
Operation
✻3
Air intake
treatment
Cleaning
Independent air ducts
(see page 4 for details)
(see page 4 for details)
(see page 4 for details)
58dB
✻1: Airflow rate is measured at the nozzle outlet. ✻2: “Alcohol” means a disinfectant containing 83% of ethanol or less. ✻3: Standard Mode.
5
Brushless
DC
Motor
Heater
JT-SB216JSH
Disabled
Friendly
Super White: clean and hygienic
Choose from a Variety of Colors
Units blend easily into any décor.
In addition to highly popular White, a variety of new colors are now available. Two-toned Dark Grey and Silver, having a dark-grey body
and silver front panel; a chic Dark Grey that is ideal for tranquil restaurant atmospheres and the like; and stylish Silver for upper-class
hotels and similar venues. The extended color line-up offers greater flexibility in color coordination and installation applications.
6
Advanced in Every Aspect for Greater Ease of Use by All
New Slim Series
1 Thorough High-speed Drying, Low-noise Operation and Saves Energy
World-first technology introduced by Mitsubishi Electric in 1993
Dual Jet Airflow
Industry top-class drying performance
Wave-shaped Nozzles
Drying time: Approx. 9~11sec
Airflow rate: 106m/sec
Air volume: 3.1m3/min
400
Remaining water [mg]
Mitsubishi Electric’s proven
Dual Jet engineering is
now complemented with a
streamlined nozzle design
that provides an optimum
balance between airflow
rate and air volume, further
enhancing efficiency and
drying hands in a matter of
seconds.
300
Previous model *2
200
Hose - le ss stru c tu re is e a sy to c le a n
Number of joints halved for improved dirt resistance
Cleansable Water Drainage Duct
Easy-to-Clean Body
Eliminating the conventional drain hose, a water drainage duct is
built into the unit, located inside the side panel. Cleaning work and
post-cleaning inspection are simple and easy; just remove the side
cover.
Innovative wave-shaped nozzles are
introduced, reducing the amount of
noise generated by the airflow
dispensed from the jets. Coupled with
an original fluid-control technology,
extremely efficient low-noise operation
has been achieved.
The number of joints at the hand inser tion section has been
r e d u c e d , e l i m i n a t i n g p l a c e s w h e r e d i r t c a n a c c u m u l a te, a n d
thereby improving both appearance and hygienic conditions. The
new unit design is more dirt-resistant and much easier to clean.
New model *1
100
0
I n c r e a s e d c o m f o r t w i t h 1 d B n o i s e r e d u c t ion
(compared to previous model*)
3 Easy to Clean and Hygienic
*JTSB216ESH/GSN
0
5
*1: JT-SB216JSH (High, Heater ON)
*2: JT-SB216ESH (Heater ON)
Time [sec]
10
15
<Previous model>
<New model>
Joints
Airflow eddy
Joints
Joint
No joint
Airflow eddy
Previous model
L ea d i n g t he i nd us t r y w i t h D ua l Je t d r y i n g
■ JT-SB216JSH/KSN: Specifications
Industry’s Lowest Power Consumption
Jet airflow
Further energy savings based on the lowest power consumption in the
industry* 1 achieved through a 2%* 2 reduction in power consumption
and standby power reduced approx. 50% compared to previous
models.
New model
Jet airflow
Eddy generated with straight nozzle outlet
flows easily, becoming a source of noise.
Eddy generated with curved nozzle outlet.
Less eddy generated, resulting in quieter
operation.
*1: For two-way jet airflow hand dryers. Applies to model with no heater
(JT-SB216KSN).
*2: Comparison of previous model, JT-SB216GSN, and new model, JT-SB216KSN.
Model name
Power
supply
JT-SB216JSH
220~240V
50~60Hz
Mode
High
Standard
JT-SB216KSN
220~240V
50~60Hz
—
Heater
Drying time Airflow rate
(sec)
(m/s)
ON
OFF
ON
OFF
9~11
11~13
11~13
13~15
—
13~15
Air volume
(m 3/min)
106
3.1
98
2.8
98
2.8
Rated
current
(A)
Power
consumption
(W)
5.7~6.2
3.9~4.2
4.9~5.3
3.0~3.2
1240
720
1070
550
3.0~3.2
550
Noise
(dB)
61
Motor type
Safety
components
Power cord
External
dimensions
(mm)
Weight
(kg)
Drain tank
(L)
Brushless
DC motor
- Thermal fuse
- Overcurrent
breaker
None
(Terminal
block
connection)
Width: 300
Depth: 219
Height: 670
11
0.8
Brushless
DC motor
- Thermal fuse
- Overcurrent
breaker
None
(Terminal
block
connection)
Width: 300
Depth: 219
Height: 670
11
0.8
58
58
✻Drying times (remaining moisture of one hand being 50mg or less) obtained using in-house measurement method. ✻Airflow rate measured at the nozzle outlet.
✻Noise measurements performed in an anechoic chamber at a distance of 2m
*Red letters indicate field wiring related dimensions
Outline Drawing JT-SB216JSH/KSN
2 User-friendly Design for All Ages
168
NEW!
Men
925mm
Women 905mm
635
Conduit
box
Terminal
block
position
Side
cover
Drain
tank
68
(79.5) (103.5)
NEW!
Easy hand access from
the side!
Recommended
height
Mounting
hole B
189
(Unit: mm)
68
Main unit 79.5
103.5
mounting
hole position Floor surface
Part B
Mounting hole details
15.5
R3
.5
A
Power
cord hole
(rear)
Power
switch
Air filter (intake port)
Awkward shoulder
movement moving
hands up/down
230
207
164
57.5
658
For younger children,* 1 who are not so tall, the upper part of the
front panel has been lowered and a “Child Sensor” added to the
upper hand-drying section to ensure detection of small hands. Even
if hands cannot reach deep inside, this sensor will detect them and
start/stop unit accordingly. Additionally, expanding on the original
open-side design, children too can use the unit to dry their hands
while standing at a relaxing, normal posture.
7
Previous
model*
Switch-door
“Open”
7
The volumetric area of the hand-drying section has been increased
approx. 1.4 times (to 6.8L from 5L of our previous model*). The
more spacious touch-free design increases the hygienic value of the
unit and ensures improved user ease for people with large hands.
Heater/
Airflow
switch
Child-conscious Design
2
267
1.4
times
219
77 93
Mounting
plate
393
Spacious Hand-drying Zone
80
263
300
28.5
15
6.5
Approx.
Women
267
Terminal
block position
Easy for small children to use
925
905
Men
670
Area
increased
•Recommended height A
10
F r e e r r a ng e o f ha nd m o v e m e nt
Mounting Diagram JT-SB216JSH/KSN
10
R3
.5
✻For fastening main unit mounting screws, use a Philips (+) screwdriver with a shaft length
of at least 150mm.
✻Mount the unit so that the left-side cover is removable and the rating label is visible.
(At least 150mm, but 200mm or more is recommended. Embedded portion is excluded.)
Allow 200mm or more to enable the water drainage duct to be checked after cleaning.
✻Allow at least 130mm between the bottom surface (air-intake port) of the unit and the floor
surface.
■Jet Towel TM Stand
Front panel shape allows hands insertion
without standing on toes.
Insert hands from the side to activate Child Sensor for quick
drying!
Floor plate
*1: At least 125cm in height
9
134
Wall
mounting
hole
Jet Towel
mounting surface
7
10
R3
.5
180
Floor plate
185
201
280
174
205
282.5
*JT- SB216ESH/GSN
A blue light that creates a feeling of cleanliness
a n d h e l p s i n t h e d r y i n g p ro c e s s c o m e s o n
when hands are placed in the air-drying section. The better visibility during use ensures
thorough drying from the wrist to the fingertips.
(10)
New Slim
7
Conventional start detection sensor
121
Conventional
start detection sensor
Depth increased
to 208mm from
180mm
15
210
R5
Child Sensor
Outline Drawing JP-S21FS2-H
Slim Series
JT-SB216JSH/KSN
10
JP-S21FS2-H (Light grey)
Floor surface
(Unit: mm)
8
Jet Towel’s many benefits make it suitable for a wide range of environments.
Office Building /Museum (California Academy of Sciences) U.S.A.
Office Building (Genesys Environmental) UK
●Factors behind the decision to use the Jet Towel:
Low carbon company so chose the
product with the lowest consumption to fit
into their own offices.
• Paper towels seen as unhygienic
• Paper towels often ran out
• Rubbish bins overflowing
“We reviewed 3 versions of hand dryers and chose the
Mitsubishi Jet Towel because of its low noise level and
low power consumption. Being a low carbon company,
we needed to follow our energy-saving principles. We
have put up signs above the Jet Towel which tells users
how much energy they are saving by using the product.
Previously we used paper towels which often ran out, so
there was either nothing to dry hands on, or so many of
them were used that the rubbish bins were overflowing.
This became unpleasant in a washroom. The Jet Towel
has made the washroom area a much nicer environment.”
Background
to Installation
Previous drying
system
In Use/
Renovated building
Paper towels
●Factors behind the decision to use the Jet Towel:
Provide the public with an
environmentally friendly
learning center in all facets
of operation.
• The Academy’s ongoing commitment to sustainability.
• Quest for LEED certification (LEED Platinum building).
• Reduce paper towel waste.
“We found that the Jet Towel is quieter,
sleeker in its design and its drying time
is quicker than its competitor, not to
mention the fact that the Jet Towel offers
users a heated stream of air rather than
a cold blast. We were actually amazed
at how well and how quickly it worked.”
Installation
History
Public restrooms
Jet Towel
installation sites throughout the facility
Restrooms throughout
Jet Towel
the facility
installation sites
Number installed
3 units
Office Building (Shanghai World Financial Center ) CHINA
Office Building (Siemens Hearing Instruments) UK
●Factors behind the decision to use the Jet Towel:
Mess gone. Time saving in not
clearing up and no monitoring
needed.
Acceptable to use paper towels but very messy
Image for customers as first point of call
Energy a concern but not the first reason for buying jet towel
“The washrooms are often the first point of
call for our visitors. As such we wanted to
provide a modern cost effective approach to
hand drying for both staff and visitors.
We selected the unheated Jet towel for our
main washrooms replacing messy paper
towels with the obvious benefits to the
appearance of our washroom and to the
environment in general.”
Background
to Installation
Previous drying
system
In Use/
Renovated building
Paper towels
Restrooms throughout
Jet Towel
the facility
installation sites
Number installed
7 units
●Factors behind the decision to use the Jet Towel:
Introduction of the High-speed
Hand Dryer to help reduce operating
expenses.
“An important consideration in installing the
High-speed Hand Dryer was whether it would help
reduce our operating expenses. So we installed the
High-speed Hand Dryer on a trial basis in an existing
building owned by Mori Building and compared the
operating costs against those incurred with the use of
paper towels. The results highlighted the superior cost
performance of the High-speed Hand Dryer, and
encouraged us to move ahead with its introduction.”
•
•
•
•
Low operating costs
Quicker drying through dual-jet airflow
Hygienic no-contact drying
Good reliability of the product quality
Background
to Installation
Previous drying
system
Commercial Building (Costco) U.S.A.
New building
—
Restrooms throughout
Jet Towel
the facility
installation sites
Number installed
No more mess in the
restrooms. Big savings by
eliminating paper towel from
budget.
New building
Previous drying
system
164 units
Hotel (Marina Mandarin) SINGAPORE
●Factors behind the decision to use the Jet Towel:
Paper towels create an unsightly mess in the restroom.
The drain tank eliminates water on the floors and walls around the dryer
“We tested 2 different types of hand
dryers. The Mitsubishi Jet Towel was
the best option for our customers.
During the trial period, our customers
liked the quieter, more approachable
looking Mitsubishi Jet Towel over the
other types of high speed hand dryers
we tested. Customer comments were
over-whelmingly positive.”
Background
to Installation
Previous drying
system
Company-wide
warehouse renovation
Paper towels
Restrooms throughout
Jet Towel
the facility
installation sites
Number installed
4 per location
4 locations
Commercial Building (Nordstrom) U.S.A.
Restroom now provide a positive
message to our clientele.
Customer feedback extremely
positive.
“Our customers have clearly shown a
preference for environmentally responsible
options in the restrooms. Our new restrooms
are low-water use, low energy use, and now
paper towel free. Before we used the Jet
Towel, we avoided hand dryers because of
the noise, slipping hazard, and most
importantly the frustration caused by the older
style of hand dryers. The Jet Towel is now a
featured fixture in our restrooms.”
We greatly reduce our
maintenance cost with Jet Towel
as there’s no need for us to
replenish paper towels and
remove the waste.
“The installation of the Jet Towels in our
restrooms helps reduce cleaning and operation
costs significantly. It also reduces paper
wastage and offers rapid drying for our guests.
There is less cumbersome work for our
maintenance to replenish paper towels or clear
waste. The design of the Jet Towel also blends
into the interior design of our restrooms and
improves our restroom ambience.”
●Factors behind the decision to use the Jet Towel:
• Create a more sanitary environment
• Reflects environmental considerations by reducing paper waste
• Quicker drying through the Dual Jet airflow
Background
to Installation
Previous drying
system
In Use/
Renovated building
Paper towels
Restrooms throughout
Jet Towel
the facility
installation sites
Number installed
18 units
Office Building / Commercial Facility (Mitsubishi Estate Co., Ltd.) JAPAN
●Factors behind the decision to use the Jet Towel:
Nordstrom needed a very quiet hand dryer to maintain pleasant
atmosphere in restroom
Low energy consumption was a major factor in decision to use
the Jet Towel
Background
to Installation
Upgrading restrooms
to become more
eco-friendly
Previous drying
system
Paper towels
Jet Towel
installation sites
Customer restrooms
throughout facility
Number installed
16 per location
4 locations
The Jet Towel blends with a wide
range of interior design schemes and
is perceived as a key restroom
amenity.
“New slim-type units were installed in all restrooms
in order to blend with the existing interior design.
Unlike with paper towels, there’s no need to
replenish supplies or remove waste, which greatly
reduces custodial work. The electric-powered
high-speed hand dryers also help to protect the
environment by eliminating the use of paper.”
●Factors behind the decision to use the Jet Towel:
• Design blends into any space
• Reduced operating and cleaning costs
• Environmentally-friendly waste-free system
Background
to Installation
New building
Previous drying
system
Restrooms throughout
Jet Towel
the facility
installation sites
Number installed
144 units
The Jet Towel is also providing excellent service in business offices, convention centres, amusement parks, shopping centres, general
industrial factories, food plants, precision machinery plants, airports and other locations where large numbers of people gather.
9
10
Download PDF