ADJ | ULTRA GO PAR7X | Specifications | ADJ ULTRA GO PAR7X Specifications

ULTRA GO PAR7X
©2013 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsufficient and negligent assembly,
installation, rigging, and operation of this product.
User Instructions
10/13
Ultra Go Par7X Introduction
Unpacking: Thank you for purchasing the Ultra Go Par7X by ADJ Products, LLC. Every Ultra Go Par7X has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The Ultra Go Par7X is a rechargeable lithium battery
powered, DMX intelligent, LED par fixture. This unit give you the freedom to set up your fixture where ever you wish without the restrictions of power. The built-in battery will keep charge for up to 5 hours
(full on) from a full, single charge. This fixture can be used in a stand
alone mode or connected in a Master/Slave configuration. This par has
five operating modes: Sound Active mode, Auto mode, RGB dimmer
mode, Static Color mode, and DMX control mode.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.American DJ.com for any comments
or suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@ADJ.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 2
Ultra Go Par7X Features
•
•
•
•
•
•
•
•
Rechargeable Lithium Battery
Mulit-Colors
Five Operating Modes
Electronic Dimming 0-100%
Built in Microphone
DMX-512 protocol
3-Pin DMX Connection
Eight DMX Modes: 1 Channel Mode, 2 Channel Mode, Two 3 Channel Modes, 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, and 7 Channel Mode.
• ADJ RFC compatiable (Not Included)
• Power Cord Daisy Chain (See page 23)
Ultra Go Par7X
Warranty Registration
The Ultra Go Par7X carries a 3 year limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
Ultra Go Par7X Installation
The unit should be mounted using a mounting clamp (not provided),
affixing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the fixture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 3
Ultra Go Par7X
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 23 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
Ultra Go Par7X
Battery Precautions
1. Handling of Batteries
1.1 Do Not Short Circuit the Battery
Try to never short circuit the battery. It generates a very high
current which could cause the battery to overheat which may
result in electrolyte gel leakage, harmful fumes, or explosion.
The LIR tabs may easily short-circuit by placing them on conductive surface. A short circuit may lead to heat build up and
damage of the battery. An appropriate circuitry with PCM is
employed to protect accidental short circuit of the battery pack.
1.2 Mechanical shock
Droping the unit, impact hit, bending, etc. may cause failure or
shortend life of the LIR battery.
3. Other
3.1 Battery connection
1). Direct soldering of wire leads or devices to the battery is
strictly prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to
the batteries. Direct soldering may cause damage of components, such as separator and insulator, by heat build up.
3.2 Prevention of short circuit within a battery pack
There is enough insulation layers between wiring and the batteries to provide extra safety protection. The battery pack is
constructed in a way that no short circuit will occur which may
cause smoke or fire.
3.3 Do No Disassemble the Batteries
1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery,
which may lead to harmful fumes, fire, explosion, or other problems.
2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the
electrolyte gel come into contact with the skin or eyes, flush the
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 4
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 5
Ultra Go Par7X
Battery Precautions
area of contact immediately with fresh water and seek medical
attention immediately.
3.4 Do Not Expose the Battery to Heat or Fire
Never incinerate or dispose of the batteries in fire. This may
cause an explosion, which would be very dangerous.
3.5 Do Not Expose the Battery to water or liquids
Never soak/drop the batteries in liquids such as water, seawater, drinks such as soft drinks, juices, coffee or other.
Ultra Go Par7X
Battery Precautions
life expectancy of the battery maybe shortened or the device
in which the battery is used may be damaged by electrolyte
gel leakage. If the batteries cannot maintain a charge for long
periods of time, even when they are charged correctly, this may
indicate it is time to change the battery.
6. Battery Disposal
Please dispose of battery according to local regulations.
3.6 Battery Replacement
For battery replacement please contact ADJ customer support
(800) 322-6337.
3.7 Do Not use a damaged Battery
The battery could be damaged during shipping, caused by
shock. Should the battery be found damaged, including damages to the plastic casing of the battery, deformation of the
battery package, smelling of an electrolyte, or leakage of the
electrolyte gel, or other, DO NOT use the battery. A battery with
a odor of electrolyte or a gel leakage should be placed away
from fire to avoid fire or explosion.
4. Battery Storage
When storing the battery, it should be stored at room temperature, with a charge of at least 50%. We recommend that during
long periods of storage that the battery be charged every 6
months. Doing this will prolong the life of the battery and will
also make sure that the battery charge does not fall below the
30% mark.
5. Other Chemical Reaction
Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if stored for a long
period of time without being used. In addition, if the various
usage conditions such as charge, discharge, ambient temperature, etc. are not maintained within the specified ranges, the
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 6
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 7
Ultra Go Par7X
Set Up
Ultra Go Par7X
Power Supply: The ADJ Ultra Go Par7X contains a automatic voltage switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
cables. Do not DMX+,DMX-,COMMON
use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does
not influence the
DMX512
DMX+,DMX-,COMMON
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
SOUND
INPUT
OUTPUT
COMMON
REMOTE
CONTROL
INPUT
1 Ground
2
3
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 8
2
OUTPUT
3
DMX -
1
2
SOUND
XLR Female Socket
2 Cold
2 Cold
1 Ground
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
Figure 2
OUTPUT
1
2
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Figure 3
3 Hot
Pin 3 = Data True (positive)
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
COMMON
XLR
DMX - Go
The Ultra Go Par7X can be controlled via DMX3-PIN
protocol.
The Ultra
Par7X has 8 DMX channel modes, please see pages 10-11 for the different modes. The DMX address is set on the back panel of the Ultra Go
Par7X. Your unit and your DMX controller require
a standard 3-pin XLR connector for data input
and data output (Figure 1). We recommend AccuCable DMX cables. If you are making your own
cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
almost all pro lighting stores). Your cables should
be made with a male and female XLR connector
on either end of the cable. Also remember that
Figure 1
DMX cable must be daisy chained and cannot be
split.
INPUT
DMX +
3
XLR Male Socket
POWER
1
1
DMX512 OUT
3-PIN XLR
SOUND
Data Cable (DMX Cable) Requirements DMX512
(ForOUT
DMX Operation):
DMX +
POWER
Notice: Be sure to DMX512
follow figures two and three when making your own
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
REMOTE
CONTROL
INPUT
Set Up
POWER
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ Products, LLC part number Z-DMX/T) will decrease the possibilities of erratic behavior. Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 9
Ultra Go Par7X
Operating Instructions
Operating Power:
There are two ways to supply power to this unit; battery power or AC
power.
• AC Power - To run the unit using AC power, plug the unit into a
power source, and put the Load Switch into the ON position. When
using AC power make sure the Battery Switch is in the OFF position.
• Battery Power - To run the unit using Battery power, put the Load
and Battery Switches in the ON position.
Operating Modes:
The Ultra Go Par7X has five operating modes:
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the ADJ Show Designer.
• RGB Mode - Choose one of the three colors to remain static or adjust the intensity of each color to make your own color.
• Sound-Active mode - The unit will react to sound, chasing through the built in programs.
• Auto Mode - There are 17 Auto Modes to choose from. 8 color fade modes, 8 color change modes, and 1 random mode.
• Static Color Mode - There are 35 colors to choose from.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Ultra
Go Par7X has 8 DMX modes: 1 Channel mode, 2 Channel mode,
3 Channel mode, a second 3 Channel mode, 4 Channel mode, 5
Channel mode, 6 Channel mode, and a 7 Channel mode. See pages
17-21 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until “dXXX” is displayed. “XXX” represents the current displayed address. Use the UP or DOWN buttons to select your desired DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 10
Ultra Go Par7X
Operating Instructions
modes. The Channel modes are listed below:
• To run the 1 Channel Mode, press the MODE button until “Ch01” is displayed. This is the 1 Channel DMX Mode.
• To run the 2 Channel Mode, press the MODE button until “Ch02” is displayed. This is the 2 Channel DMX Mode.
• To run the 3 Channel Mode, press the MODE button until “Ch03” is displayed. This is the 3 Channel DMX Mode.
• To run the other 3 Channel Mode, press the MODE button until “Ch3A” is displayed. This is the other 3 Channel DMX Mode.
• To run the 4 Channel Mode, press the MODE button until “Ch04” is displayed. This is the 4 Channel DMX Mode.
• To run the 5 Channel Mode, press the MODE button until “Ch05” is displayed. This is the 5 Channel DMX Mode.
• To run the 6 Channel Mode, press the MODE button until “Ch06” is displayed. This is the 6 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until “Ch07” is displayed. This is the 7 Channel DMX Mode.
4. Please see pages 17-21 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX control-
ler.
RGB Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “r.XXX” is displayed you are in Red dimming mode. Press the UP and DOWN buttons to adjust intensity. After you have finished adjusting the intensity, or you would like to skip to the next color, press the SET UP button.
3. When “G.XXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to adjust intensity.
4. When “b.XXX” is displayed you are in Blue dimming mode. Press the UP and DOWN buttons to adjust intensity.
5. After you have adjusted the RGB colors to make your desired color you can then activate strobing by pressing the SET UP but-
ton to enter the Flash (strobe) mode.
6. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 11
Ultra Go Par7X
Operating Instructions
Sound Active Mode:
In this mode the Ultra Go Par7X will react to sound, and chase
through the different colors.
1. Plug the fixture in and press the MODE button until “So-XX” is displayed. “XX” represents the sound active mode (1-8) currently displayed. Use the UP and DOWN buttons to scroll through th sound active modes.
2. After you have found your desired sound active mode, press the SET UP button to adjust the sound sensitivity. “SJ-X” will be dis-
played. Use the UP and DOWN buttons to adjust the sensitivity. “SJ-1” is the lowest sensitivity, “SJ-8” is the highest.
Auto Run Mode:
There are 3 types of Auto Run Modes to choose from; Color Fade,
Color Change, and both modes running together. The running speed
is adjustable in all 3 modes.
1. Plug the fixture in and press the MODE button until either
“AFXX”, “AJXX”, or “A-JF” is displayed. Press the SET UP Button to change between the 3 Auto Run modes
• AFXX = Color Fade mode, there are 8 Color Fade modes to
choose from. Use the UP or DOWN buttons to scroll through the different Auto Fade modes.
• AJXX = Color Change mode, there are 8 Color Change modes to choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.
• A-JF = Both Color Fade and Color Change modes running.
2. After you have chosen your desired running mode press the SET UP button until “SP.XX” is displayed. When this is displayed you can adjust the running speed of your desired program. Use the UP or DOWN button to adust the speed between “SP.01” (slow-
est) and “SP.16” (fastest). Once you have set your desired running speed, press the SET UP button to return to your desired Auto Run Mode.
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLXX” is displayed.
2. There are 35 colors to choose from. Select your desired color by pressing the UP and DOWN buttons. After you have selected your ADJ Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 12
Ultra Go Par7X
Operating Instructions
desired color you can activate strobing by pressing the SET UP button to enter the Flash (strobe) mode.
3. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).
LED Display On/Off:
To set the LED display to turn off after 20 seconds, press the MODE
button until “don” is displayed, press the UP button to display “doff”.
Now the display will disappear after 20s. Press any button to turn the
display on again. Be advised though that the display will turn off automatically after 20 seconds.
To set the display press the MODE button until “dXX” is displayed.
Use the UP or DOWN buttons to select either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 20 seconds.
ADJ RFC:
This function is used to activate and deactivate the ADJ RFC (Remote
Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see the next page for ADJ RFC controls
and functions.
1. Plug the fixture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “rFXX” is displayed. “XX” repre-
sents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
LED Display Inversion:
Follow these instructions to flip the display 180° so that the display
can be read upside down.
1. Plug the fixture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until either “Stnd” or “rEv” is displayed.
3. Press the UP or DOWN buttons to reverse the display 180°.
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 13
Ultra Go Par7X
Operating Instructions
1. Plug the fixture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the MODE button to exit.
Battery Life:
This menu is used to check/display the battery life.
1. Plug the fixture in and press the MODE button until “bXXX” is dis- played. “XXX” represents a number between 0-100. The number that is displayed is the remaining battery life. If “b---” is displayed, it means either the battery is dead or your running the unit on AC power.
Dimming Curve:
This is used to set the dimming curve used with DMX mode.
1. Plug the fixture in and press the MODE button until the DMX address is displayed.
2. Press the SET UP button until “dr-X” is displayed. This is the dim-
mer setting. “X” represents the dimming mode.
3. Use the UP and DOWN buttons to find your desired dimming curve. Press SET UP when you are finished.
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 14
Ultra Go Par7X
Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a MasterSlave mode. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together. Remember that the Male XLR connector is the input and the Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
2. Connect the first “Slave” unit to the “Master.”
3. Set the “Master” unit to your desired mode of operation.
4. On the “Slave” unit press the MODE button until “SLAv” is dis-
played. The “Slave” unit will now follow the “Master”.
Ultra Go Par7X
©ADJ
Photometric Chart
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 15
Ultra Go Par7X
ADJ RFC Operation
The ADJ RFC remote (sold seperately) has many different functions and allows you to control your Ultra Go Par7X from long distance. The ADJ RFC
remote can control your system up to 150 ft. To use the RFC you must first
activate the fixtures receiver, to activate the receiver please see the instructions on page 10.
Ultra Go Par7X
Channel
1
0 - 10
11 - 17
BLACKOUT - Pressing this button will blackout the fixture. Press this button for more then 3 seconds to activate default running mode. All modes will
return to their default settings.
AUTO RUN - This button will run 1 of 3 auto run programs. Each press
of the button will scroll through Color Fade, Color Change, and Random.
When you activate Color Fade, you can use the “+” and “-” buttons to scroll
through the 8 different color fade modes. When you activate Color Change,
you can use the “+” and “-” buttons to scroll through the 8 different color
change modes. You can control the fade speed and color change speed of
the Auto Run by pressing the speed button and then adjust the speed using
the “+” and “-” buttons.
PROGRAM SELECTION - This button will activate Static Color mode.
Press this button to activate Static Color mode. Use the “+” or “-” to scroll
through the 35 colors. Once you have found your color, you can press the
Flash Button to activate strobing and use the “+” or “-” to adjust the Flash
rate.
FLASH - This button will activate the flash (strobe) effect. You can control
the flash speed by pressing the “+” and “-” buttons.
SPEED - Press this button and use the “+” & “-” buttons to adjust the speed
of the Built-In Programs.
SOUND ACTIVE - This button activates sound active mode. Use the “+” &
“-” buttons to scroll through the 8 sound active modes. Press this button
againg to switch to sound sensitivity adjustment and then use the “+” & “-”
buttons to adjust the sound sensitivity level.
R G B - Press either one of these buttons and the press the “+” or “-” to adjust the brightness.
“+” and “-” - Use these buttons to adjust the flash rate, speed of the Auto
Run, fade speed, sound sensitivity, and output intensity. Use these buttons
to scroll through the static colors.
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 16
Value
©ADJ
18 - 24
25 - 31
32 - 38
39 - 45
46 - 52
53 - 59
60 - 66
67 - 73
74 - 80
81 - 87
88 - 94
95 - 101
102 - 108
109 - 115
116 - 122
123 - 129
130 - 136
137 - 143
144 - 150
151 - 157
158 - 164
165 - 171
172 - 178
179 - 185
186 - 192
193 - 199
200 - 206
207 - 213
214 - 220
221 - 227
228 - 234
235 - 241
242 - 248
249 - 255
1 Channel - DMX Values & Functions
Function
COLOR MACROS
OFF
BASTARD AMBER
MEDIUM AMBER
PALE AMBER GOLD
GALLO GOLD
GOLDEN AMBER
LIGHT RED
MEDIUM RED
MEDIUM PINK
BROADWAY PINK
FOLLIES PINK
LIGHT LAVENDER
SPECIAL LAVENDER
LAVENDER
INDIGO
HEMSLEY BLUE
TIPTON BLUE
LIGHT STEEL BLUE
LIGHT SKY BLUE
SKY BLUE
BRILLIANT BLUE
LIGHT GREEN BLUE
BRIGHT BLUE
PRIMARY BLUE
CONGO BLUE
PALE YELLOW GREEN
MOSS GREEN
PRIMARY GREEN
DOUBLE CTB
FULL CTB
HALF CTB
DARK BLUE
WHITE
FULL RED
FULL GREEN
FULL BLUE
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 17
Ultra Go Par7X
Channel
Value
1
1 - 255
2
1 - 255
Ultra Go Par7X
Channel
Value
1
1 - 255
2
3
1 - 255
0 - 15
16 - 255
Ultra Go Par7X
Channel
1
2 Channel - DMX Values & Functions
Function
COLOR MACROS
(See 1 Channel DMX mode for colors)
DIMMER 0% - 100%
3 Channel - DMX Values & Functions
Function
COLOR MACROS
(See 1 Channel DMX mode for colors)
DIMMER 0% - 100%
STROBING
NOTHING
STROBING SLOW - FAST
3A Channel - DMX Values & Functions
Value
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
1 - 255
2
1 - 255
3
1 - 255
Ultra Go Par7X
Channel
1
2
1 - 255
3
1 - 255
4
1 - 255
©ADJ
4 Channel - DMX Values & Functions
Value
1 - 255
Function
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
MASTER DIMMER
0% - 100%
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 18
Ultra Go Par7X
Channel
Value
5 Channel - DMX Values & Functions
Function
1
RED
1 - 255
0% - 100%
2
GREEN
1 - 255
0% - 100%
3
BLUE
1 - 255
0% - 100%
4
MASTER DIMMER
1 - 255
0% - 100%
5
1 - 255
COLOR MACROS
(See 1 Channel DMX mode for colors)
Channels 1, 2, and 3 will not work, when Channel 5 is being
used.
Ultra Go Par7X
Channel
Value
6 Channel - DMX Values & Functions
Function
1
RED
1 - 255
0% - 100%
2
GREEN
1 - 255
0% - 100%
3
BLUE
1 - 255
0% - 100%
4
MASTER DIMMER
1 - 255
0% - 100%
5
STROBING
0 - 15
NOTHING
16 - 255
STROBING SLOW - FAST
6
1 - 255
COLOR MACROS
(See 1 Channel DMX mode for colors)
Channels 1, 2, and 3 will not work, when Channel 6 is being
used.
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 19
Ultra Go Par7X
Channel
1
Value
0 - 255
2
0 - 255
3
0 - 255
4
0 - 255
5
0 - 15
16 - 255
0 - 255
0 - 31
32 - 255
6
0 - 51
52 - 102
103 - 153
154 - 204
205 - 255
7
0 - 255
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
©ADJ
7 Channel - DMX Values & Functions
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
MASTER DIMMER
0% - 100%
STROBING/PROGRAM SPEED/
SOUND SENSITIVITY
NO FUNCTION
STROBING SLOW - FAST
SPEED CONTROL SLOW - FAST
SOUND SENSITIVITY
NO FUNCTION
LEAST SENSITIVE - MOST SENSITIVE
PROGRAM SELECTION MODE
DIMMING MODE
COLOR MACRO MODE
COLOR CHANGE MODE
COLOR FADE MODE
SOUND ACTIVE MODE
COLOR MACROS/PROGRAMS/
SOUND ACTIVITY
COLOR MACRO MODE
(See 1 Channel DMX mode for colors)
COLOR CHANGE MODE
COLOR CHANGE 1
COLOR CHANGE 2
COLOR CHANGE 3
COLOR CHANGE 4
COLOR CHANGE 5
COLOR CHANGE 6
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 20
Ultra Go Par7X
Channel
8
Value
7 Channel - DMX Values & Functions
Function
192 - 223
224 - 255
COLOR CHANGE MODE CONT.
COLOR CHANGE 7
COLOR CHANGE 8
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
COLOR FADE MODE
COLOR FADE 1
COLOR FADE 2
COLOR FADE 3
COLOR FADE 4
COLOR FADE 5
COLOR FADE 6
COLOR FADE 7
COLOR FADE 8
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
SOUND ACTIVE MODE
SOUND ACTIVE MODE 1
SOUND ACTIVE MODE 2
SOUND ACTIVE MODE 3
SOUND ACTIVE MODE 4
SOUND ACTIVE MODE 5
SOUND ACTIVE MODE 6
SOUND ACTIVE MODE 7
SOUND ACTIVE MODE 8
When Channel 6 is between the values of 0-51, Channels 1-3 are used,
and Channel 5 will control strobing.
When Channel 6 is between the values of 52-102, Channel 7 is in Color
Macros Mode, and Channel 5 will control strobing.
When Channel 6 is between the values of 103-153, Channel 7 is in Color
Change Mode, and Channel 5 will control the color change speed.
When Channel 6 is between the values of 154-204, Channel 7 is in Color
Fade Mode, and Channel 5 will control the color fade speed.
When Channel 6 is between the values of 205-255, Channel 7 is in Sound
Active Mode, and Channel 5 will control the sound sensitivity.
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 21
Ultra Go Par7X
Battery Status & Charging
Battery Status:
This function is used to check the life status of the battery.
Plug the fixture in and press the MODE button until “bXXX” is
displayed. “XXX” represents an number between “000” and
“100”. The number that is displayed is the remaining battery
life. If “b---” is displayed, it means the battery is dead or you are
running the unit on AC power. Please do not let the battery
fully die, this severly shortens the life of the battery.
Example: If “b050” is displayed, the battery is at half life. If
“b025” is displayed, the battery is at 25% life.
NOTE: When the battery is charging or if the battery life is
below 30% the digital display will flicker.
Battery Recharge: To recharge the battery, plug the supplied AC
cord into the AC input on the side of the unit and plug the other
end into a matching power supply. It takes about 4.5 hours to
reach full charge.
For a faster recharge, put the Load Switch in the “Off” position
and the Battery Switch in the “ON” position.
Ultra Go Par7X
Battery Replacement
Battery replacement is a very easy procedure. Unscrew the two
thumbscrews located on the side of the unit.
Carefully slide the battery out and disconnect the wire.
Connect the new battery and slide the battery back in. Screw the two
thumbscrews back in to secure the battery.
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 22
Ultra Go Par7X
Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 12 fixtures maximum. After 12 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
Ultra Go Par7X
Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that the
fuse holder is located inside the power socket. Insert a flat-head screw
driver into the power socket and gently pry out the fuse holder. Remove
the bad fuse and replace with a new one. The fuse holder also has a
holder for a spare fuse.
Ultra Go Par7X
Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
Ultra Go Par7X
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 23
Ultra Go Par7X
Warranty
Ultra Go Par7X
Notes
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 3-year (1095 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 24
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 25
Ultra Go Par7X
Model: Ultra Go Par7X
Specifications
Voltage: 100V ~ 240V/50~60Hz
Battery Life:
5 Hours Full On (Full Charge)
Battery Lifetime*:
Average Lifetime is 500 Charges
LEDs:
7 x 3W TRI LED’s (3-in-1 RGB)
Beam Angle:
40 Degrees
Working Position: Any safe working position
Power Draw:
48W
Power Cord Daisy Chain:12 Fixtures Max.
Fuse:
2 Amp
Weight: 8lbs./ 3.4Kgs.
Dimensions: 10.5” (L) x 10” (W) x 5.5” (H)
265 x 252 x 134mm
Colors:
RGB Color Mixing
DMX Channels:
8 DMX Modes: 1 Channel Mode, 2 Channel Mode, Two 3 Channel Modes, 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, & 7 Channel Mode
Warranty**:
3 Year (1,095 days)
*This depends on charging frequency
**See Warranty page for details
Auto Sensing Voltage: This fixture contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into
the power source.
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
©ADJ
Products, LLC - www.adj.com - Ultra Go Par7X User Manual Page 26
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Download PDF