CCTV
Specification
CCTV
Model:
PCC338
Picture Type:
Colour
Image Sensor:
Sony 1/3” Super HAD CCD
DSP:
Xvision IXC1
Resolution:
500TVL
Lens Viewing Angle:
Varifocal- 23 to 90°
Infra Red Nightvision:
No
Minimum Illumination:
0.1 Lux
Audio:
Yes
Operating Voltage:
12V DC 220mA
Suggested Power Supply:
12V DC 300mA Regulated
• The camera must be positioned so that it will not point directly into the sun (sunrise and
Mounting:
Wall/Ceiling
• Avoid viewing areas where half the area is in bright sunlight and the other half is dark,
Weatherproofing:
Optional Housing Required
Dimensions:
50x45x140mm
TECHNICAL SUPPORT:
For Technical Support for any Xvision product please contact your local
distributor.
LIMITED WARRANTY:
This product is supplied with a limited 2 Year warranty. The Warranty
excludes products that have been misused, (including accidental
damage) and damage caused by normal wear and tear. In the unlikely
event that you encounter a problem with this product, it should be
returned to the place of purchase.
Model: PCC338
Colour ‘Traditional’ Camera
with Varifocal Lens
Before you begin
• Please unpack the box carefully and identify that all the parts are present.
The camera is suitable for indoor use only (unless used with an optional external housing).
Please bear in mind the following points when choosing a mounting position.
sunset) or any bright light, as this may cause damage to the camera.
such as in the shadow of a building. All types of cameras have difficulty in ‘seeing’ with
such a large lux level variation.
Manufactured exclusively for:
Xvision (Europe) Group,
Head Office: London, U.K.
Email: [email protected]
Web: www.x-vision.co.uk
• Do not cut the camera cables, this will void the warranty.
• Make sure you use only the recommended power supply. Damage caused to the camera by
incorrect voltage or wiring is not covered by the warranty.
Model:
PCC338
Colour ‘Traditional’ Camera with
Varifocal Lens
Package Contents
Identify Camera Parts
Operation
1. Connect the Video Output 1 to the monitor or other video device
through a 75 Ohms type coaxial cable.
2 Connect the power source 2 to the DC socket by using the DC jack
(+12V DC in jack centre) and the camera will power up lighting the
LED indicator 3 .
3. Once the picture appears on the monitor, open the cover 4 and
adjust the lens screw for ‘WIDE <--------->TELE’ 5 to get the viewing
angle that you require, then adjust the focus screw of the lens to
obtain the best picture (loosen by turning anti clockwise and tighten
by turning clockwise).
PCC338 Camera
4. Tighten screws 5 and 6 fully and then replace the cover 4 .
Main Features
• Super High Resolution CCD sensor provides great quality Colour images
in light levels of 0.1 lux and above
Figure 1
6. DIP switch 8 Setting
6.1- BLC FUNCTION
Set switch-OFF/BLC to BLC to enable Back Light Compensation (BLC)
function.
• Traditional styling makes it ideal for use in situations where an instant
deterrent is required
• Sony 1/3" Super HAD CCD image sensor for 500 TVL resolution images
and 0.1 lux low light sensitivity
6.2- AUTO IRIS FUNCTION
The switch should be in the OFF position to disable the AES function.
Adjust the LEVEL with the VR 9 to proper level.
• Xvision IXC1 Digital Signal Processing (DSP) chip which has been
optimised for internal viewing and features Automatic Gain Control,
Automatic Electronic Iris, Auto White Balance, Back Light Compensation,
Low Smear, Edge Enhancement and Zero Colour Rolling
• The PCC338 features an Xvision Pixel+ Varifocal 3.3 to 12.0mm lens
with 23° to 90° viewing angle for super sharp images and easy
selection of the optimum viewing angle during installation.
• Designed for internal use as supplied and can be wall or ceiling
mounted by adding an internal camera bracket and used externally by
adding a weatherproof housing.
5. Mount the camera on a mounting bracket by using the holes 7 on
top or bottom (depending on whether you are wall or ceiling
mounting the camera) of the camera.
6.3- AGC-LO/AGC-HI FUNCTION
When in the ON position the maximum AGC gain is approximately
26dB. In the OFF position the maximum AGC gain is approximately
16dB. For better night time performance switch this ON. Please note
this will also make the picture appear more grainy.
Figure 2- Rear Connections
6.4-FLICKERLESS FUNCTION
Set switch to OFF position to enable flickerless function. In this mode
the switch AES/OFF is auto disabled. This should be left to the OFF
position as the camera has an Auto Iris lens. Turning ON this function
will show you an alternative colour balance under some lighting
conditions.
">