Volvo 2004 S40 Owner's Manual


Add to my manuals
206 Pages

advertisement

Volvo 2004 S40 Owner's Manual | Manualzz
2004
VOLVO
S40
TP 7012 (French). AT 0347. Printed in Sweden, Elanders Graphic Systems AB, Gšteborg 2003
CONDUITE ET ENTRETIEN S40
TP 7012
WEB EDITION
2004
Introduction
Dear Volvo owner
We hope you will enjoy many years of driving pleasure in your Volvo. The car has been designed for the safety and comfort of you and your
passengers. Volvo is one of the safest cars in the world. Your Volvo has also been designed to satisfy all current safety and environmental
requirements. In order to increase your enjoyment of the car, we recommend that you familiarise yourself with the equipment, instructions and
maintenance information contained in this owner's manual.
Thank you for choosing Volvo!
1
Introduction
Owner's manual
A good way of getting to know your new car
is to read the owner's manual, ideally before
your first journey. This will give you the
opportunity to familiarise yourself with new
functions, to see how best to handle the car
in different situations, and to make the best
use of all the car's features. Please pay
attention to the safety instructions contained
in the manual:
WARNING!
Warning texts indicate where there is a
risk of personal injury in the event of the
instructions not being followed.
IMPORTANT!
Caution texts indicate a risk of damage to
the car in the event of the instructions not
being followed.
The equipment described in the owner's
manual is not present in all models. In
addition to standard equipment, this manual
also describes options (factory fitted
equipment) and certain accessories (extra
equipment).
2
NOTE! Volvo cars are differently equipped
depending on the requirements of the
different markets and the national or local
legal requirements and regulations.
The specifications, design features and
illustrations in this Owner’s Manual are not
binding. We reserve the right to make
modifications without prior notice.
© Volvo Car Corporation
Introduction
Volvo Cars’ Environmental
philosophy
Environmental care, safety and quality are the
three core values which influence all
operations of the Volvo Car Corporation.
Volvo cars comply with strict international
environmental standards and are
manufactured in plants, which are among the
cleanest and most resource-efficient in the
world. Most units within Volvo Car
Corporation are certified to the environmental
standards ISO 14001 or EMAS, which leads
to continuous improvements within the area
of the environment. Volvo Cars is the first car
manufacturer to have a third-party certified
environmental declaration where the
customer can compare the environmental
effects of different models and engines. Read
more at:
www.epd.volvocars.se
Clean inside and out
Your Volvo is built to be "Clean inside and
out", a concept which means you benefit in
two ways - from a clean cabin and a highly
efficient exhaust purification system. Your car
saves fuel and releases minimal quantities of
harmful substances. It also ensures that you
and your passengers do not inhale emissions
from other cars by cleaning the air that comes
into the passenger compartment. A
sophisticated air cleaning system ensures
that the air in the passenger compartment is
cleaner than the air outside. The interior is
free of allergenic substances and there is a
special coating, Premair®1 , on the radiator
which converts dangerous ground level
ozone to pure oxygen.
1
Volvo's workshops and the
environment
Regular maintenance at a Volvo workshop
creates the conditions for low fuel
consumption and thus contributes to a
cleaner environment. The personnel have the
knowledge and tools to guarantee the best
possible environmental care.
Applies to cars with five cylinder engines.
3
Introduction
Save the environment
We believe that our customers share our
concerns about the environment. You can
help save the environment by purchasing
environmentally optimised car care products
and by servicing and maintaining the car
according to the instructions in the owner’s
manual.
•
Relax the accelerator pedal on downhill
slopes.
•
Use engine braking. Release the
accelerator and change down.
•
Avoid idling. Switch off the engine when
queuing in traffic.
•
Remember to dispose of hazardous
waste, e.g. batteries and oil, in an
environmentally favourable manner. Seek
advice from your Volvo workshop if
unsure about disposal.
•
Maintain the ignition and fuel systems,
which directly reduce exhaust
emissions.
Below are a few tips on how to save the
environment:
•
•
Always ensure that the tyres are at the
correct pressure. Too low tyre pressure
results in increased fuel consumption.
The roof rack and ski-boxes have greater
air resistance and raise fuel
consumption considerably. Remove
them directly after use.
•
Remove unnecessary items from the
car. The greater the load, the higher the
fuel consumption.
•
Always use the engine block heater
before a cold start, if the car is equipped
with one. This will reduce fuel
consumption and emissions.
•
Drive gently. Avoid unnecessary quick
acceleration and heavy braking.
•
Drive in the highest gear possible. Low
engine rpm gives lower consumption.
4
By following this advice fuel consumption can
be reduced without affecting either the
journey time or the enjoyment of driving. You
preserve the car, money and the planet's
resources.
Table of Contents
Instrument overview
Safety
Instruments and controls
Climate control
Interior
Locks and alarm
Starting and driving
Wheels and tyres
Car care
Maintenance and service
Infotainment
Specifications
7
13
33
59
71
83
93
119
133
139
163
191
5
Table of Contents
6
Instrument overview
Instrument overview
Overview left-hand drive cars
Overview right-hand drive cars
Driver’s door control panel
8
10
12
7
Instrument overview
Overview, left-hand drive cars
Left-hand drive
8
Instrument overview
23.
Display for climate control and
infotainment
24.
Infotainment
25.
Settings for climate control,
infotainment and personal settings
Lighting, fuel filler flap opener
26.
Climate control
Door handle, central locking
27.
Gear lever
7.
Air vents in the dashboard
28.
Air vent, side window
8.
Air vent side window
29.
Door handle
9.
Cruise control
30.
Glovebox
10.
Horn, airbag
31.
Control panel
11.
Combined instrument panel
32.
Parking brake
12.
Keypad Infotainment
33.
Electric socket/Cigarette lighter
34.
Stability system STC or DSTC
35.
Switch, optional equipment
1.
Steering wheel adjustment
2.
Bonnet release
3.
Control panel
4.
Direction indicators, main beam, trip
computer
5.
6.
13.
Windscreen wipers and washers,
headlamp washers
14.
Ignition switch
15.
Rearview mirror, compass
16.
Seat belt reminder
17.
Interior lighting left-hand side
18.
Movement detector, alarm
19.
Interior lighting function switch
20.
Position for accessory switch
21.
Interior lighting right-hand side
22.
Operation, sunroof
9
Instrument overview
Overview right-hand drive car
Right-hand drive
10
Instrument overview
24.
Direction indicators, main beam, trip
computer
Electric socket
25.
Cruise control
Parking brake
26.
Combined instrument panel
5.
Control panel
27.
Horn, airbag
6.
Glovebox
28.
Infotainment
7.
Central locking
29.
Air vent, side window
8.
Air vent, side window
30.
Central locking
9.
Air vents in the dashboard
31.
Lighting, fuel filler flap opener
10.
Gear lever
32.
11.
Climate control
Windscreen wipers and washers,
headlamp washers
12.
Settings, climate control and
infotainment
33.
Control panel
34.
Bonnet release
35.
Steering wheel adjustment
1.
Switch, post installed accessory
2.
Stability system STC or DSTC
3.
4.
13.
Infotainment
14.
Display, climate control and
infotainment
15.
Operation, sunroof
16.
Interior lighting, left-hand side
17.
Central locking
18.
Interior lighting, switch
19.
Switch, post installed accessory
20.
Interior lighting, right-hand side
21.
Seat belt reminder
22.
Mirrors, compass
23.
Ignition switch
11
Instrument overview
Driver’s door control panel
Electric child lock (option).
Power windows
Door mirror, left-hand side
Door mirrors, setting
Door mirror, right-hand side
12
Safety
Safety
Seat belts
Airbags
Side airbags
Inflatable curtain
WHIPS
When are the safety systems activated?
Crash mode
Inspecting air bags and inflatable curtains
Child safety
14
17
20
22
23
25
26
27
28
13
Safety
Seat belts
Release the belt:
• Press the red button in the lock and
allow the reel to retract the belt. If the
belt is not completely retracted, feed in
the belt manually to prevent it from
hanging loose.
The belt is restricted and cannot be pulled
out further:
• if it is pulled out too fast
Extending the lap belt. The belt must be
positioned low down.
Always use a seat belt
Braking could have serious consequences if
the seat belt is not used. Ensure that all
passengers are wearing their seatbelts.
Otherwise, rear seat passengers may be
thrown against the front seat backrests in a
collision.
Putting on the seat belt:
• Pull the belt out slowly and secure it by
inserting the locking tab into the lock. A
loud "click" indicates that the belt is
locked.
14
•
during braking and acceleration
•
if the car leans heavily.
It is important that the belt lies snugly against
the body so it can provide maximum
protection. Do not lean the backrest too far
back. The seat belt is designed to protect in
a normal seating position.
Keep the following in mind:
• do not use clips or anything else that
prevents the belt from fitting correctly
•
ensure the belt is not twisted or caught
on anything
•
the lap belt must sit low down (not over
the abdomen)
•
stretch the lap belt over the lap by
pulling the diagonal shoulder belt as
illustrated.
WARNING!
The seat belt and airbag operate
together. If the seatbelt is not used or is
incorrectly used airbag operation can be
affected in the event of a collision.
WARNING!
Each belt is intended for one person
only.
WARNING!
• If the belt has been exposed to a major
load, in a collision for example, the entire
belt must be replaced. This includes
reels, mountings, screws and locks.
Some of the protective characteristics of
the belt may have been lost, even if the
belt does not appear to be damaged.
Replace the seat belt if it is worn or
damaged. The new seat belt must be
approved and intended for installation in
the same position as the replaced belt.
• Never modify or repair the seatbelts
yourself. Contact a Volvo workshop.
Safety
an audible signal is heard that changes
frequency depending on the speed of the car.
Rear seat
The seat belt reminder is activated if a
passenger in the rear seat takes off the seat
belt during a journey. If one of the rear doors
is opened and closed, the system checks for
ten seconds how many of the seat belts are
in use and presents this number in the
information display, e.g. 2-3 REAR BELTS IN
USE. No light or audible reminder is given.
This only takes place when a seat belt is
removed.
Seat belt
reminder1
A symbol lights up in the roof console (above
the rearview mirror) as a reminder that the
seat belt is not being worn. A symbol also
lights up on the dashboard. If the car is
stationary, the reminder disappears after
approximately 6 seconds.
The seat belt reminder for the rear seat can
be switched off:
• Hold in the READ-button on the lefthand steering wheel stalk until a
message verifies that the function has
been switched off.
Pregnant women
Pregnant women must take particular care
when securing the seat belt. Position the belt
so that it does not exert unnecessary
pressure on the womb. The lap belt of the
three-point seat belt should be low.
Front seat
The symbols remain lit if the driver or front
passenger is not wearing their seat belt. (No
signal is given if a child seat is installed in the
front seat.) In addition to the two lit symbols,
1
The functions may vary slightly depending
on the market
15
Safety
Seat belt tensioner
All the seat belts (with the exception of the
rear centre position) have seat belt
tensioners. This is a mechanism which, at the
moment of impact, tensions the seatbelt
around the body. The belt therefore restrains
the passenger more quickly.
Marking on seat belts with seat belt
tensioners
16
Safety
Airbags
WARNING!
• No objects or accessories may be
positioned or stuck on, or near, the
SRS AIRBAG panel (above the glove
box) or in the area affected by the
airbag.
• Never interfere with SRS
components in the steering wheel or
the panel above the glove box.
Driver’s airbag
In addition to the seat belts, the car has an
airbag (SRS - Supplemental Restraint
System) in the steering wheel. The airbag is
folded into the centre of the steering wheel.
The wheel is marked SRS AIRBAG.
Front passenger airbag1
The airbag on the passenger side is
folded up in a compartment above the
glove box. The panel is marked SRS
AIRBAG.
WARNING!
WARNING!
To minimise the risk of injury if the airbag
deploys, passengers must sit as upright
as possible with their feet on the floor
and backs against the backrest. Seat
belts should be secured.
The seat belt and airbag operate
together. If the seatbelt is not used or is
incorrectly used airbag operation can be
affected in the event of a collision.
1
WARNING!
• Never place a child seat or booster
cushion on the passenger seat if the
car has an airbag on the passenger
side.
• Never allow a child to stand or sit in
front of the front passenger seat.
• No one shorter than 140 cm (4 ft 7)
should sit in the front passenger
seat.
Not all cars have passenger side air bags. It
can be optionally excluded at purchase.
17
Safety
WARNING!
If the SRS warning symbol remains lit or
lights while driving, it means that the
SRS system is not functioning fully. The
symbol can also indicate a fault in the
seat belt buckle, the SIPS or the IC
system. Contact a Volvo workshop
immediately.
Location of the airbag on the passenger
side, left-hand drive/right-hand drive cars
Warning symbol in the centre of
the dashboard
The SRS system is continuously monitored
by the car's electronic system. The warning
symbol in the combined instrument panel
lights when the ignition key is turned to
positions I, II or III. The symbol goes out
after approximately six seconds if the SRS
system is fault-free.
18
As well as the symbol, a
message appears in the
information display. If the
warning symbol is defective,
the warning triangle is lit and
the message SRS AIRBAG
SERVICE URGENT appears
in the display.
Safety
NOTE! In certain collisions, only one (or no)
airbag is activated.
WARNING!
Any interference in the SRS system
could cause malfunction and serious
injury.
Repair work may only be performed by a
Volvo workshop.
SRS system, left-hand drive
SRS system, right-hand drive.
SRS System
NOTE! The sensors (3) react differently
depending on the severity of the collision and
whether the driver or passenger side seat
belts are in use. Crash situations may occur
where only one airbag is deployed. In a
collision, the SRS system sensors detect the
deceleration caused by the collision. The
system determines if the collision is of the
character and nature requiring one or more
airbags to deploy to protect the occupants.
The system consists of a gas generator (1)
surrounded by the inflatable airbag (2). Upon
a sufficiently violent collision, sensors (3)
react, activating the gas generator igniters
and the airbag inflates as it heats up. To
cushion the impact, the airbag deflates when
compressed. When this occurs, smoke also
escapes into the car. This is completely
normal. The entire process, including inflation
and deflation of the airbag, occurs in tenths of
a second.
Dual-stage airbags
(Volvo Dual-Stage Airbag)
If a collision is mild but sufficiently violent that
there is a risk of personal injury, the airbags
are partially inflated. If the collision is more
severe, the airbags are inflated fully.
19
Safety
Side airbags
WARNING!
Only use Volvo upholstery or upholstery
approved by Volvo. Other upholstery
may impede the function of the side
airbags.
Child seats and side airbags
A child seat/booster cushion can be placed
in the front seat as long as the car is not
equipped with an airbag on the passenger
side.
Side airbags - SIPS bag
A large proportion of the collision force is
distributed by SIPS to the members, posts,
floor, roof and other parts of the car body.
The side airbags protect the chest and are an
important part of SIPS. The SIPS airbag
system consists of two main components:
Side airbags and sensors. The side airbags
are installed in the frames of the front seat
backrests and the sensors are located on the
insides of the centre and rear pillars.
WARNING!
The side airbags supplement the
existing SIPS system. Always use seat
belts.
20
WARNING!
• Any interference with the SIPS (side
impact protection system) airbag
system could cause malfunction and
serious injury. Contact a Volvo
Workshop instead.
• No objects or accessories may be
placed between the outer side of the
seat and the door panel because this
area may be affected by the side
airbag.
Safety
Left-hand drive
Right-hand drive
Side impact protection system
(SIPS)
The SIPS airbag consists of a gas generator
(1), side airbag(2) and sensors (3). When a
sufficiently violent collision occurs, the
sensors react and activate the gas generator
which inflates the side airbag. The airbag
inflates between the occupant and the door
panel, cushioning the impact at the moment
of collision, and then deflates. Normally, only
the side airbag on the side of the collision
inflates.
21
Safety
Inflatable curtain
Properties
The inflatable curtain supplements the
existing SIPS system. The inflatable curtain is
concealed in the headlining along both sides
of the car. It protects both the front and rear
seat. If the car is hit from the side, the
inflatable curtain deploys within a few
thousandths of a second. It is then inflated for
approximately three seconds to provide
maximum protection in the event of a
complicated, severe collision. The inflatable
curtain is activated by the SIPS system
collision sensors if the car is hit from the side.
The inflatable curtain is filled with gas when
activated. The inflatable curtain helps to
prevent the driver's and passengers heads
from hitting the inside of the car in the event
of a collision.
22
WARNING!
• Never hang or secure anything from
the handles in the roof. The hook is
only intended for light outer garments
(not for hard objects such as
umbrellas).
• Do not screw to, or mount anything
on the headlining, door pillars or side
panels. The intended protection may
then be compromised. Only Volvo
Genuine parts that are approved for
placement in these areas should be
used.
WARNING!
The inflatable curtain is a supplement to
the seat belt.
Always use a seat belt.
Safety
WHIPS
WARNING!
• If the seat has been exposed to a heavy
load strain, such as in a rear-end
collision, the WHIPS system must be
inspected by a Volvo workshop.
• Even if the seat seems undamaged,
some of the protective properties of
the WHIPS system may have been
lost. Contact a Volvo workshop to
check the system, even after minor
rear end collisions.
Protection against whiplash
injuries - WHIPS
The WHIPS system ( Whiplash Protection
System) consists of energy absorbing
backrests and specially developed head
restraints in both front seats. The system is
activated upon a collision from behind, based
on the collision angle, speed and nature of
the colliding vehicle.
WARNING!
The WHIPS system is a supplement to
the seat belt. Always use seat belts.
The seat's properties
When the WHIPS system is activated the
front seat backrests fall backwards to alter
the position of the driver's and passengers in
the front. This diminishes the risk of whiplash
injury.
WARNING!
Never modify or repair the seat or
WHIPS system yourself. Contact a
Volvo workshop.
Correct seating position
For the best possible protection, the driver
and front seat passenger should sit in the
centre of the seat with as little distance as
possible between the head restraints and
head.
WHIPS system and child seats
The WHIPS system does not negatively
affect the protective properties of the car with
regard to child seats.
23
Safety
The following can be used:
• a child seat in the front passenger seat,
provided that the airbag on the
passenger side has been deactivated.
•
a rear facing child seat in the rear seat
supported against the backrest of the
front seat.
Do not hinder the function of the
WHIPS system
WARNING!
If a rear backrest is folded down, the
corresponding front seat must be moved
forward so that it is not in contact with
the folded backrest.
WARNING!
Do not place a box or similar cargo so
that it is squeezed between the seat
cushion of the rear seat and the backrest
of the front seat. Be sure to never hinder
the function of the WHIPS system.
24
Safety
When are the safety systems activated?
System
Triggered
Seat belt tensioner
In frontal collisions. The seat belt is tensioned around the body to restrain the passenger more quickly.
Airbags (SRS)
In collisions if there is a risk that front seat passengers could be injured by hitting the dashboard or
steering wheel.
Side airbags SIPS
In side-on collisions if the car is hit with sufficient force.
Inflatable Curtain (IC)
In side-on collisions. The curtain reduces the risk of head injuries.
Whiplash protection (WHIPS)
When hit from behind. Reduces the risk of whiplash.
If the airbags have been deployed, we
recommend the following:
•
Tow the car to a Volvo workshop. Never
drive with deployed airbags.
•
Let a Volvo workshop replace
components in the car's safety system.
•
The airbags do not always deploy in the
event of a frontal collision. This means
that the function was not needed at that
moment and the passengers were
protected by the other safety systems of
the car.
NOTE! The SRS, SIPS and IC systems are
only deployed once in a collision.
WARNING!
The SRS system sensor is located in the
centre console. Disconnect the battery
cables if the floor of the passenger
compartment has been drenched with
water. Do not try to start the car, as the
airbags may deploy. Have the car
recovered to a Volvo workshop.
WARNING!
Never drive with deployed airbags.
This may make the car difficult to steer.
Other safety systems may also be
damaged. Intense exposure to the
smoke and dust released when the air
bags are deployed can cause skin and
eye irritation. In case of problems, wash
with cold water and contact a doctor.
The speed of the deployment and the
airbag fabric may cause friction burns on
the skin.
25
Safety
Crash mode
WARNING!
Never try to repair the car yourself or to
reset the electronics after the car has
been in CRASH MODE. This could
result in injury or the car not functioning
as normal. Always allow a Volvo
workshop to handle checking and
restoring the car to normal status after
CRASH MODE has been displayed.
Attempting to start the car
First check that no fuel has escaped from the
car. There should not be any fuel odour.
Driving after a collision
If the car has been involved in a collision, the
text CRASH MODE - SEE MANUAL may
appear in the information display. This means
the functionality of the car has been reduced.
CRASH MODE is a safety feature that
comes into effect when the collision could
have damaged an important function in the
car, for example fuel lines, sensors for one of
the safety systems or the brake system.
26
WARNING!
Do not attempt to restart the car under
any circumstances if there is any fuel
odour when the CRASH MODE
message is displayed. Leave the car
immediately.
If everything appears normal and you have
checked for fuel leakage, you may attempt to
start the car.
• First remove the ignition key, then
reinsert it. The car's electronics will try
to reset themselves to normal mode.
Then try to start the car.
Moving the car
If the normal mode is displayed after the
CRASH MODE has been reset, the car may
be moved carefully out of its present
dangerous position. Do not move the car
further than necessary.
Recovery
Even if the car appears driveable after it has
been put into CRASH MODE, it should not
be driven or towed. When travelling,
concealed damage can make the car
impossible to manoeuvre.
WARNING!
The car may not be towed once it has be
put in CRASH MODE. It must be
recovered from its present location to a
Volvo workshop.
Safety
Inspecting air bags and inflatable curtains
Inspection intervals
1. Driver’s airbag
The year and month specified on the decal on
the door pillar(s) is the date you should
contact your Volvo Workshop to inspect, and
if necessary, replace the airbags, seat belt
tensioners and inflatable curtains. If you have
any questions about the systems, please
contact a Volvo workshop.
2. Front passenger airbag
3. Side airbag on the driver’s side
4. Side airbag on the passenger side
5. Inflatable curtain on the driver’s side
6. Inflatable curtain on the passenger side
This decal is located in the rear left door
opening.
27
Safety
Child safety
NOTE! Regulations regarding where children
may be placed in the car vary from country to
country. Check what laws apply.
Children should sit comfortably
and safely
The position of the child in the car and the
equipment required is dictated by the weight
and height of the child. The table “Position of
children” page 30 in the car gives the
necessary information.
•
Children of all ages and sizes must
always be secured in the car. Never
allow a child to sit on the knee of a
passenger.
Volvo’s own child safety equipment is
designed for your car. The use of Volvo
genuine equipment ensures that the
mounting points and attachments are
correctly positioned and sufficiently strong.
28
Child seats and airbags are not compatible
Child seats and airbags
Always place the child in the rear seat if the
passenger seat airbag is activated. If the
airbag deploys, a child seated in a child seat
on the passenger side may suffer serious
injury.
WARNING!
No one shorter than 140 cm (4 ft 7 in)
should sit in the front seat.
Safety
Decals on the side of the dashboard
WARNING!
Never place a child seat/booster
cushion on the front seat if the car has an
airbag on the passenger side.
29
Safety
Position of children in the car
Weight/age
Front seat
Outer rear seats
Centre rear seat
<10 kg (22 lbs)
Rear-facing child seat, secured
with seat belt and mounting strap.
L: Type approval no. E5 03135
Rear-facing child seat, secured
with seat belt, support and
mounting strap.
L: Type approval no. E5 03135
Rear-facing child seat, secured
with seat belt, support and
mounting strap.
L: Type approval no. E5 03135
Rear-facing child seat, secured
with seat belt and mounting strap.
L: Type approval no. E5 03135
Rear-facing child seat, secured
with seat belt, support and
mounting strap.
L: Type approval no. E5 03135
Rear-facing child seat, secured
with seat belt, support and
mounting strap.
L: Type approval no. E5 03135
Booster cushion with or without
backrest.
L: Type approval no. E5 03139
Alternatives:
Booster cushion with or without
backrest.
L: Type approval no. E5 03139
Integrated booster cushion.
L: Type approval no. E5 03168
Booster cushion with or without
backrest.
L: Type approval no. E5 03139
(0–9 months)
9-18 kg (19 – 40 lbs)
(9 –36 months)
15-36 kg (33 – 80 lbs)
(3-12 years)
L: Suitable for certain child seats as listed in
the specified type approval. Child seats may
be vehicle-specific, limited, semi-universal or
universal.
WARNING!
• Never place a child in a child seat or on
a booster cushion on the front seat if
the passenger seat airbag is activated.
• Never leave children unattended.
30
Safety
ISOFIX mounting system for
child seats (option)
Integrated booster cushions
(option)
The outer rear seats are fitted with ISOFIX
mountings. Contact a Volvo dealer for further
information on child safety equipment.
Volvo’s integrated booster cushion for the
rear outer seats is specially designed to
provide optimum safety for children.
Combined with the regular seat belts, the
booster cushion is approved for children
weighing between 15 and 36 kg. (33 – 80
lbs).
Raising the booster cushion
1. Pull the handle to raise the booster
cushion.
2. Grasp the cushion with both hands and
move it backwards.
3. Press until it locks.
WARNING!
The booster cushion must be in the
locked position before a child is placed
there.
Check that:
• the seat belt is in contact with the
child’s body and is not slack or twisted
over the shoulder
31
Safety
WARNING!
If an integrated booster cushion has
been exposed to a major load, in a
collision for example, the entire booster
cushion must be replaced. This includes
the seat belt, complete with bolts. Even
if the booster cushion appears
undamaged, some of the protective
properties may have been lost. The
booster cushion must be replaced if it is
worn.
•
the lap belt is low over the pelvis for
optimum protection
• the seat belt does not touch the child’s
throat or lie below the shoulders.
Carefully adjust the position of the head
restraint to suit the child.
See also page 158.
Lowering
1. Pull the handle
2. Move the seat down and press until it
locks
NOTE! Remember to first stow the
booster -cushion if you wish to lower the
seat’s backrest.
32
Replacing the booster cushion
It is important that the integrated booster
cushion is properly secured. Therefore,
replacement and any repairs to the cushion
should be carried out by a Volvo workshop.
Do not modify or adapt the booster cushion
in any way.
Installing the child seat
Volvo has child safety products that are
designed for and tested by Volvo.
When using other products that are available
on the market, it is important to read the
installation instructions that accompany the
product and to follow them carefully.
•
Do not attach the child seat straps to
the horizontal adjustment bar, springs or
the rails and struts under the seat.
Sharp edges may damage the mounting
straps.
•
Allow the backrest of the child seat to
rest against the dashboard. This applies
to cars that do not have a passenger
side airbag or if the airbag is
deactivated.
•
Never place a child seat on the front
seat if the car has a passenger side
airbag that is not deactivated. If there
are any problems with installation of
child safety products, contact the
manufacturer for clearer installation
instructions.
Instruments and controls
Instruments and controls
Combined instrument panel
Check and warning symbols
Information display
Electrical socket and switch for the centre
console
Lighting panel
Left-hand steering wheel stalk
Cruise control (option)
Right-hand steering wheel stalk
Steering wheel adjustment, hazard warning
flashers
Parking brake, electrical socket
Power windows
Rearview/Door mirrors
Power sunroof (option)
Personal preferences
34
35
39
40
41
43
45
46
48
49
50
52
55
57
33
Instruments and controls
Combined instrument panel
press (more than 2 seconds) resets the
activated trip odometer.
11. Display
Displays the gear positions for automatic
gearbox, rain sensor, trip and odometer
and cruise control.
12. Main beam indication
13. Button for the clock
Turn the button to set the time.
1. Speedometer
5.
2. Direction indicators, left
6.
Direction indicators, right
3. Warning symbol
7.
Tachometer
Indicates engine speed in thousands of
revolutions per minute (RPM). Do not
allow the needle of the tachometer to
enter the red field.
4. Information display
The display presents information and
warning messages, outside temperature
and clock. When the temperature is
between +2 °C and –5 °C, a snowflake
symbol is shown in the display. This
symbol serves as a warning for slippery
road surfaces. When the car has been
stationary, the outside temperature
gauge may display a higher reading than
the actual temperature.
34
Information symbol
8.
Check and warning symbols
9.
Fuel gauge
10. Button for the trip odometer
Used to measure short distances. Briefly
pressing the button switches between
the two trip odometers T1 and T2. A long
14. Temperature gauge
The temperature of the engine cooling
system. If the temperature is abnormally
high and the needle enters the red zone,
a message is shown in the display. Bear
in mind that extra lamps in front of the air
intake reduce the cooling capacity at
high outside temperatures and high
engine loads.
15. Check and warning symbols
Instruments and controls
Check and warning symbols
Function test, symbols
3.
All the check and warning symbols light when
the ignition key is turned to position II before
starting. The operation of the symbols is then
verified. All the symbols should go out when
the engine is started, apart from the
handbrake symbol which only goes out when
the handbrake is disengaged.
If the engine is not started within 5 seconds,
Remedy according to the instructions or
contact a Volvo workshop.
If there is a deviation in one of
the systems in the car, the yellow
information symbol lights up in
combination with text in the
display. The information symbol
can also be lit in combination
with other symbols.
all symbols go out except for
and
.
Certain symbols may not have the function
indicated, depending on the car’s
specification.
NOTE! The car can be driven for a further
period following a service-related message.
Consult your Volvo workshop.
Symbols in the centre of the
dashboard
The red warning triangle is lit
when a fault has been indicated
that can affect safety and/or the
car's driveability. Explanatory
text appears in the information
display at the same time. The
warning symbol can also be lit
in combination with other
symbols.
1.
Stop in a safe place. The car should not
be driven any further.
2.
Read the information in the display.
35
Instruments and controls
3.
3.
If the symbol remains lit, drive to a
Volvo workshop to have the ABS
system checked.
Rear fog lamp
This symbol lights when the fog
lamp is on.
4.
Stability system STC or DSTC
The flashing symbol indicates that
the stability system is in operation.
If the warning symbol remains lit,
this indicates low road friction.
Indicator symbols - left-hand
side
1.
5.
No function
6.
Engine preheater (diesel)
The symbol is lit while the engine
is being preheated. Preheating
starts when the temperature falls
below -2 °C. The car can be
started when the lamp goes out.
Fault in the emissions system
Drive to a Volvo workshop to have
the system checked.
2.
Fault in the ABS system
The system is not working if the
symbol lights. The car’s normal
braking system continues to work,
but without the ABS function.
1.
2.
36
Stop the car in a safe place and
switch off the engine.
Restart the engine.
7.
Indicator symbol - right-hand
side
1.
The symbol flashes when the
direction indicators of the car and
trailer are used. If the symbol does
not flash, one of the lamps on the
trailer or car is defective.
Low level in the fuel tank
There are approximately 8 litres
left when this symbol is lit.
Trailer indicator lamp
2.
Parking brake applied
The symbol lights even if the
parking brake has only been
applied one “click”. Check that
the lever is properly applied.
Instruments and controls
3.
Airbags - SRS
1.
If the symbol remains lit or lights
while driving, a fault has been
detected in the SRS, SIPS or IC
system. Drive to an authorised
Volvo workshop as soon as
possible to have the system
checked.
4.
2.
Low oil pressure
If the BRAKE and ABS symbols
light at the same time, there may
be a problem in the brake forcedistribution.
If the symbol lights while driving,
the engine oil pressure is too low.
Stop the engine immediately and
check the engine oil level. Top up
if necessary. If the symbol is lit and
the oil level is normal, contact a
Volvo workshop.
5.
Seat belt reminder
The symbol remains lit if the driver
or front passenger is not wearing
their seat belt.
6.
Generator not charging
If this symbol lights while driving,
there is a fault in the electrical
system. Contact a Volvo
workshop.
7.
Fault in the brake system
If the symbol lights, the brake fluid
level may be too low.
Stop the car in a safe place and
check the brake fluid reservoir
level.
If the reservoir level is below MIN,
the car should not be driven
further. Have the car recovered to
a Volvo workshop to have the
brake system checked.
1.
Stop the car in a safe place and
switch off the engine.
2.
Restart the engine.
•
If both symbols go out, continue driving.
•
If the symbols remain lit, check the brake
fluid reservoir level.
•
If the brake fluid level is normal and the
symbols remain lit, carefully drive the car
to a Volvo workshop to have the brake
system checked.
•
If the reservoir level is below MIN, the
car should not be driven further. Have
the car recovered to a Volvo workshop
to have the brake system checked.
WARNING!
If the BRAKE and ABS symbols light at
the same time, there is a risk that the rear
end will slide during heavy braking.
Reminder - doors not closed
If one of the doors, the bonnet or the boot lid
is not correctly closed, the driver will be
warned.
Low speed
While the car is moving at a
maximum of 7 km/h (4.5 mph), the
symbol lights. At the same time,
one of the following will appear in
the display: DRIVER DOOR
OPEN, PASSENGER DOOR
OPEN, LEFT REAR DOOR
OPEN or RIGHT REAR DOOR
OPEN. Stop the car as soon as it
is safe to do so. Close the door or
the hatch which is open.
High speed
If the car is being driven at 7 km/h
(4.5 mph) or more, the symbol
lights. At the same time one of the
texts in the previous paragraph is
displayed.
37
Instruments and controls
Bonnet 1 and boot lid
Irrespective of speed, the symbol
lights and the display shows
BONNET OPEN or BOOT LID
OPEN.
1
38
Only cars with an alarm.
Instruments and controls
Information display
Messages
At the same time as a warning or indicator
symbol is lit, a supplementary message
appears in the information display.
•
Press the READ button (A).
Scroll between the messages using the
READ button. Fault messages are stored in
the memory until the fault has been remedied.
NOTE! If a warning message is displayed
when the trip computer is being used, the
message must be read (press the READ
button) before the previous activity can be
resumed.
Message
Specification
STOP SAFELY
Stop the car and switch off the engine. Serious risk of damage.
STOP ENGINE
Stop the car and switch off the engine. Serious risk of damage.
SERVICE URGENT
Take your car in for service immediately.
SEE MANUAL
Read the owner's manual.
SERVICE REQUIRED
Take your car in for service as soon as possible.
TIME FOR REGULAR SERVICE
Time for service. The time is affected by the distance travelled, number of
months since last service and engine running time.
39
Instruments and controls
Electrical socket and switch for the centre console
Cigarette lighter (option)
The lighter is activated by pushing in the
button. Once the lighter has been heated, the
button pops out again. Pull out the lighter and
use the heated coils.
Stability system STC or DSTC1
The stability and traction control system is
activated automatically when the car is
started.
Electric socket, DSTC system, extra
equipment
To reduce the stability control system:
• Hold the button pressed for at least half
a second.
For further information, see page 138.
12V electric socket
WARNING!
The electric socket can be used for different
12 V accessories, such as mobile phones
and coolers. The maximum current is 10A. In
order for the socket to supply current, the
ignition key must be in position I.
The driving characteristics of the car
differ if the stability control system
function is reduced.
Extra equipment
WARNING!
Always leave the plug in the socket when
the socket is not in use.
Space for extra switch for post installed
equipment.
1
40
Option in certain markets
Instruments and controls
Lighting panel
2. Headlamps and position/
parking lamps
in all positions, even when the key is not in the
ignition switch. See also page 43.
All lighting off.
Cars with daytime running
lights (certain countries)
Dipped beam lights automatically
when the ignition key is switched to the
driving position (II) and cannot be switched
off. Before trips to certain countries, the
daytime running lights can be deactivated.
Contact a Volvo workshop. Front and rear
parking lamps, number plate lighting and
instrument lighting are lit at the same time as
dipped beam.
1. Headlamp levelling
The headlamp height is adjusted using this
control. This is used when the car is so
heavily laden that it affects the height of the
beams.
•
•
Normal beam height - move the control
upwards (0).
Lowered beam height - move the control
downwards.
Cars with Bi-Xenon lighting (option) have
automatic headlamp levelling.
Position/parking lamps
Front and rear position/parking
lamps as well as number plate
lighting and instrument lighting.
Main and dipped beam
Ignition key in position II:
Headlamps (plus front and rear
parking lamps, number plate
lighting and instrument lighting)
are lit.
NOTE! The light switch must be turned to
position II to switch on the main beam.
However, it is possible to flash the main beam
3. Instrument lighting
Manual adjustment:
• Brighter illumination - move the control
upwards.
•
Weaker illumination - move the control
downwards.
Automatic control:
A twilight sensor automatically adjusts the
brightness of instrument illumination.
4. Fog lamps (option)
Ignition key in position II:
• Press the button.
The fog lamps light in combination with
the position/parking lamps and main/
dipped beam. The LED in the button is
lit while the fog lamps are on.
NOTE! In some countries, dipped beam or
main beam may not be used in combination
with front fog lamps.
5. Fuel filler flap
•
Press the button to open the flap
covering the fuel cap.
41
Instruments and controls
6. Rear fog lamp
Ignition key in position II:
• Press the button to switch the fog tail
lamp on. The rear fog lamp lights in
combination with the main/dipped
beam. The LED in the button and the
symbol in the combined instrument
panel light. If the front fog lamps and the
main or dipped beam are switched off
and on again, the rear fog lamp goes
out. Press the button to switch it on
again.
Dazzling
Remember to switch off the fog tail lamp
when a car is seen in the rear view mirror.
Only the last car in a queue should have the
fog tail lamp switched on.
NOTE! Regulations for use of front and rear
fog lamps vary from country to country.
42
Instruments and controls
Left-hand steering wheel stalk
Main beam flash (3)
Pull the lever towards you (until you feel a
slight resistance). The main beam remains lit
until the lever is released.
Switching, main and dipped beam (3)
Pull the lever towards you past the flash
position and release it to change between
main and dipped beam.
Home safe light (3)
Carry out the following when you leave your
car when it is dark outside or when there is
poor visibility:
1. Remove the key from the ignition switch.
Direction indicators, light switch
and main beam flash
Resistance point position (1)
When changing lanes or overtaking, move
the lever until you feel a distinct resistance.
The lever returns when released. This action
results in three flashes.
Normal turns (2)
The direction indicators light when you move
the lever in the direction the wheel moves
during the turn. When the steering wheel
returns to centre after a turn, the direction
indicators switch off automatically.
2.
Move the steering wheel lever towards
you.
Trip computer
3.
Exit the car.
Controls
In order to gain access to the information in
the trip computer, the thumbwheel INFO (B)
must be turned in steps, either upward or
downward. By turning again, you return to the
starting point.
4. Lock the doors.
The dipped-beam lighting, position/parking
lights, number plate lighting and door mirror
lamps (option) will switch on. These lamps
will remain lit for 30, 60 or 90 seconds. The
desired time setting can be adjusted in the
Car settings menu in the centre console
display. See the Personal Settings section for
further information.
NOTE! If a warning message interrupts while
the trip computer is in use, the message must
be acknowledged. Acknowledge by pressing
the READ button (A) and to revert to the trip
computer function.
43
Instruments and controls
Functions
The trip computer receives a great deal of
data that is continuously evaluated by a
microprocessor.
The system has four functions which are
shown in the display:
• Average speed
•
Current fuel consumption
•
Average fuel consumption
•
Range to empty fuel tank
Average speed
When the ignition is switched off, the
average speed is stored and used as the
basis of the new value when you continue
driving. Reset using the RESET button (C).
Current fuel consumption
Present fuel consumption is calculated every
second. The information in the display is
updated every couple of seconds. When the
car is stationary, “----“ appears in the display.
Average fuel consumption
The average fuel consumption since the last
reset (RESET). When the ignition is switched
off, the average fuel consumption is stored
and remains until the function is reset. Reset
using the RESET button (C).
44
NOTE! Some incorrect readings may occur if
a fuel-driven heater is used.
Range to empty fuel tank
This calculation is based on the average fuel
consumption over the last 30 km (19 miles)
and the remaining fuel volume. It displays the
approximate distance that can be driven with
the fuel remaining in the tank. When the
range to empty is less than 20 km (12 miles),
“----“ is shown in the display.
NOTE! Some incorrect readings may occur if
a fuel-driven heater is used.
Resetting
Keep the RESET button (C) pressed for at
least five seconds to reset the average speed
and average fuel consumption at the same
time.
Instruments and controls
Cruise control (option)
CRUISE ON is displayed when the cruise
control is activated.
Temporary disengagement
• Press 0 to temporarily disengage the
cruise control.
Cruise control is automatically disengaged:
• if the speed drops below the limit for
engagement
Operation
Activating
The controls for cruise control are to the left
of the steering wheel.
Setting the desired speed:
• Press the CRUISE button. CRUISE is
displayed.
•
Increase or decrease the speed by
pressing + or –.
NOTE! Cruise control cannot be
engaged at speeds below 35 km/h (22
mph).
•
Lightly press + or – to lock the desired
speed.
•
when the brake pedal or the clutch
pedal is depressed.
•
if the gear selector is moved to position
N
A short press corresponds to approximately
1 km/h (0.6 mph). The speed of the car at the
time the button is released will be
programmed instead.
Disengagement
• Press CRUISE to disengage the cruise
control. CRUISE ON will go out in the
display. The cruise control is
automatically disengaged when the
ignition is switched off.
• during wheel spin or wheel lock-up.
The last set speed is stored in the memory.
Return to the set speed
Press the button to resume the
previously set speed.
Acceleration
A temporary increase in speed, during
overtaking for example, does not affect the
cruise control setting. The car will resume the
previously set speed afterwards. If cruise
control is engaged, the speed can be
increased or decreased using the + or –
button.
45
Instruments and controls
Right-hand steering wheel stalk
Intermittent wiping
The number of sweeps per time
unit can be adjusted. Turn the
thumb wheel (C) upwards for a
shorter interval between the
sweeps. Turn downwards to
increase the interval.
Continuous wiping
The wipers sweep at normal
speed
The wipers sweep at high speed
Windscreen wipers
A. Windscreen and headlamp washers
B. Rain sensor - on/off
C. Thumb wheel
D. No function
Windscreen wipers off
The windscreen wipers are off
when the stalk is in position
Single sweep
Move the stalk up to make a single
sweep.
46
A – Windscreen/ headlamp
washers
Pull the lever towards the steering wheel to
start the windscreen and headlamp washers.
The wipers will make three more sweeps
once the stalk is released.
Headlamp washing
(option in certain markets)
High pressure washing of the headlamps
consumes a large quantity of washer fluid. To
save fluid, the headlamps are only washed
every fifth time (within a ten minute interval).
When ten minutes has passed since the last
time the windscreen was washed, the
headlamps are washed again at high
pressure the next time the windscreen is
washed.
B – Rain sensor (option)
The rain sensor detects the amount of water
on the windscreen so that the speed of the
windscreen wipers increases or decreases.
The sensitivity of the rain sensors is adjusted
using the thumb wheel (C).
On/Off
When activating the rain sensor, the
windshield wiper stalk must be in position 0.
To activate the rain sensor:
• press the button (B). The rain sensor
symbol is shown in the lower display.
Instruments and controls
To switch off the rain sensor, either:
• press the button (B)
• change the wiper program by moving
the stalk to another position.
The rain sensor switches off automatically
when the ignition is switched off.
IMPORTANT!
Disengage the rain sensor at automatic
car washes or switch off the ignition. The
windshield wipers start and may become
damaged.
C – Thumb wheel
The thumb wheel is used to adjust the
number of sweeps per interval when
Intermittent wiping is selected or the
sensitivity to rainfall when the rain sensor is
selected.
D – No function
47
Instruments and controls
Steering wheel adjustment, hazard warning flashers
WARNING!
Adjust the steering wheel before driving,
never while driving. Before driving,
check that the steering wheel is fixed in
position.
Steering wheel adjustment
Hazard warning flashers
The steering wheel can be adjusted for both
rake and reach.
1. Fold down the lever by the steering
column to release the steering wheel.
2. Adjust the steering wheel to the position
that suits you best.
3. Fold the lever back to secure the
steering wheel position. If the lever is
hard to move, press on the steering
wheel at the same time as pressing the
lever back.
Use the hazard warning flashers (all direction
indicators flash) when the car is stopped
where it could be a possible traffic hazard or
obstruction. Press the button to activate the
function.
48
NOTE! Regulations for use of hazard warning
flashers vary from country to country.
Instruments and controls
Parking brake, electrical socket
Cigarette lighter (option)
Press the lighter in to activate the function.
Once the lighter has been heated, it pops out
again. Pull out the lighter and use the heated
coils.
Parking brake ( handbrake)
Electric socket in the rear seat
The lever is located between the front seats.
The parking brake holds the rear wheels. The
warning symbol in the combined instrument
panel lights when the brake is applied.
The electric socket can be used for various
accessories, such as mobile phones and
coolers. It is intended for 12 V. The maximum
current is 10A. The ignition key must be in the
lowest position I for the socket to supply
current.
The warning symbol lights even if the parking
brake has only been applied one “click”.
Check that the lever is properly applied.
To release the parking brake:
•
Pull the lever up slightly and press in the
button. Lower the lever and release the
button.
WARNING!
Always leave the plug in the socket when
the socket is not in use.
49
Instruments and controls
Power windows
Operation
The power windows are operated using the
controls in the door armrests. The ignition key
must be in position or for the power
windows to work. Once you have stopped
driving and removed the ignition key, the
windows can still be opened or closed as
long as neither of the front doors are opened.
To open the window:
• Depress the front section of the control.
To close the window:
• Pull the front section of the control up.
WARNING!
Ensure that children's or other
passengers' hands are clear when
closing the windows.
Remote control and central locking
buttons
All side windows can automatically be
opened/closed using the remote control or
the central locking buttons:
• Hold the lock button pressed for two
seconds - the windows open or close.
If you need to interrupt opening/closing:
• Press the lock button again.
50
A. Front door windows B. Rear door
windows
Driver's door
The driver can control all the power windows
from his seat.
The windows in the front doors can be
opened and closed in two ways:
1.
Press one of the controls (A) or (B)
down gently or pull it up gently. The
power windows go up or down as long
as the switch is actuated.
2.
Press one of the controls (A) or (B)
down fully or pull it up fully, then release.
The windows then open or close
automatically. Movement is stopped if
the window is blocked in any way.
WARNING!
If the rear door windows are being
operated from the driver’s door, check
that no rear seat passengers are in
danger of getting caught when the
windows close.
Blocking power windows in the rear
doors
The LED in the switch is unlit
Rear door windows can be operated both by
the controls on the doors and the control on
the driver’s door.
The LED in the switch is lit
Rear door windows can only be operated
from the driver’s door.
Instruments and controls
NOTE! If the car has electric child safety
locks 1the LED indicates that these are
activated. The doors cannot then be opened
from the inside.
WARNING!
Always remember to switch off the
current to the power windows (i.e.
remove the ignition key) if children are
left in the car unattended.
Passenger seat, front
The control for the power window at the
passenger seat operates that window only.
Power windows in the rear
doors
The rear door windows can be operated with
the controls on the doors or the switch on the
driver’s door.
If the LED in the switch for blocking power
windows in the rear doors (located in the
control panel in the driver’s door) is lit, the
rear door windows can only be operated from
the driver’s door.
The windows in the rear doors are operated
in the same way as the windows in the front
doors.
1
Option
51
Instruments and controls
Rearview/Door mirrors
Rearview mirror
Dimming
Dimming is performed with the lever (1).
2. Normal position
3.
Dimming position. Used when the light
from the vehicle behind is intrusive.
Dimming, automatic dim function
(option)
A sensor (4) in the bottom edge of the mirror
detects light coming from behind, and dims
the mirror when the light is strong. A Volvo
workshop can adjust the sensitivity.
NOTE! The illustration is a montage. The
mirror has either manual or automatic
dimming, never both at the same time.
52
Rearview mirror with compass
(option)
The upper right-hand corner of the rearview
mirror has an integrated display that shows
the compass direction in which the front of
the car is pointing. Eight different illustrations
are displayed with English abbreviations: N
(North), NE (North East), E (East), SE (South
East), S (South), SW (South West), W
(West) and NW (North West).
Calibrating the compass
The compass may need to be calibrated in
special cases. (installing weatherstrip). If
calibration is required, the character C
appears in the mirror's display.
1.
2.
3.
4.
5.
Stop the car in a large, open area.
Start the car.
Hold the button (1) depressed (use a
pen, for example) for at least six
seconds. The character C will be
displayed again.
Drive slowly in a circle at a maximum
speed of 10 km/h (6 mph) until a
compass direction is displayed.
Calibration is complete.
Instruments and controls
IMPORTANT!
Do not use ice scrapers with steel blades
to remove ice from the mirrors as the glass
could be scratched. Use the defroster
function instead. See the Climate Control
section for more information.
WARNING!
The driver's side mirror is wide angled to
provide optimal vision. Objects may
appear further away than they actually
are.
Magnetic zones
Adjusting the zone
The earth is divided into 15 magnetic zones.
The compass is adjusted for the
geographical area to which the car was
delivered.
Select a different compass area as follows:
1. Turn on the ignition.
2. Hold the button (1) depressed (use a
pen, for example) for at least 3 seconds.
The number for the current area is
displayed.
3. Press the button repeatedly until the
number for the required geographical
area (1-15) is displayed.
4. A few seconds after browsing is
complete, the display reverts to the
compass direction.
Door mirrors
The controls for setting the door mirrors are
at the front of the armrest on the driver’s door.
1. Press the L button for the left-hand door
mirror or R for the right-hand door
mirror. The LED in the button lights.
2. Adjust the position with the adjustment
control in the centre.
3. Press the L or R button again. The LED
should no longer be lit.
Retractable power door mirrors
(option)
The mirrors can be retracted for parking/
driving in narrow areas.
•
Press the L and R buttons at the same
time. Release them after approximately
one second. The mirrors automatically
stop in the fully retracted position.
Fold out the mirrors
• Press the L and R buttons at the same
time. The mirrors automatically stop in
the fully extended position.
53
Instruments and controls
Resetting to the neutral position
Mirrors that have been moved out of position
as a result of external influences must be
reset to the neutral position in order for
electric folding to function.
Proceed as follows:
• Fold in the mirrors using the L and R
buttons.
•
Fold out the mirrors again using the L
and R buttons. The mirrors are now
reset to the neutral position.
Approach lighting
The lamps on the door mirrors light when
home safe lighting or approach lighting is
selected.
54
Instruments and controls
Power sunroof (option)
From ventilation position to fully open sun
roof:
•
Pull the control backwards to the end
position (1) and release.
Sliding position
Automatic operation
Pull the control over the resistance point
position (2) to the rear end position (1) or
over the resistance point position (3) to the
forward end position (4) and release. Sun
roof opens/closes fully.
Opening positions
1.
Opening, automatic
The sunroof controls are located in the
headlining. The sunroof can be opened to
two positions:
• Ventilation position, raised at the rear
edge (A)
2.
Opening, manual
3.
Closing, manual
4.
Closing, automatic
5.
Opening, ventilation position
•
6.
Closing, ventilation position
Sliding position, backwards/forwards
(B)
The ignition key must be in position I or II.
WARNING!
Remember to switch off the current to
the sunroof (remove the ignition key) if
children are left in the car unattended.
Ventilation position
Open:
• Push the trailing edge of the control (5)
upward.
Close:
• Pull the trailing edge of the control (6)
downward.
Manual operation
Open:
• Pull the control backwards to the
resistance point position (2). The
sunroof will move towards maximum
opening position as long as the button
is held in.
Close:
• Press the control forwards to the
resistance point (3). The sunroof will
move towards the closed position as
long as the button is held in.
WARNING!
The sunroof's pinch protection function
only operates during automatic closing,
not manual closing.
55
Instruments and controls
opened. Grip the handle and slide the screen
forwards to close the screen.
Pinch protection
The sunroof pinch protection function is
activated if the hatch is blocked by an object.
If blocked, the sunroof will stop and
automatically open to the previous position.
WARNING!
Closing using the remote
control or the central locking
button
Closing using the remote control or the
central locking button:
• Hold the lock button pressed for two
seconds. The sunroof and windows
close. The doors lock.
If you need to interrupt closing:
• Press the lock button again.
Sun screen
The sunroof features a manually-operated
sliding inner sun screen. The sun screen
slides back automatically when the sunroof is
56
The sunroof's pinch protection function
only operates during automatic closing,
not manual closing.
Make sure that children's hands are
clear when closing the sunroof.
Instruments and controls
Personal preferences
Possible settings
General
Personal preferences are available for some
of the car's functions. Applies to locks-,
climate control and audio functions. For audio
functions, see page 167.
Personal preferences can be entered for
climate, locks and audio functions. For audio
functions, see page 167
Lock functions
Control panel
Lock Feedback Light
When the car is locked/unlocked using the
remote control, the hazard warning flashers
can be selected to flash. The alternatives On/
Off are available for both locking and
unlocking.
A. Display
B. MENU
C. EXIT
D. ENTER
E. Navigation
Autolock
When the car starts to move, the doors and
boot lid can be locked automatically. The
alternatives On/Off are available.
Use
The settings are presented in the display (A).
Open the menu to enter settings:
1. Press the MENU (B).
2.
Scroll to Car Settings using the
navigation button (E).
3.
Press ENTER (D).
4.
Select an alternative using the
navigation button (E).
5.
Confirm your selection with ENTER.
Close the menu:
• Press EXIT (C).
Unlock
There are two alternatives for unlocking:
1. Global (all doors). Unlocks all doors with
one press on the remote control.
2. Two Step (two step unlocking). Unlocks
the driver's door with one press on the
remote control. Another press unlocks all
the doors.
Control panel
Approach light
Selects the time the car's light should remain
lit when pressing the Approach Light button
on the remote control. The following options
can be selected: 30/60/90 seconds.
57
Instruments and controls
Home safe light
Selects the time the car's light should remain
lit when the left-hand steering wheel stalk is
pulled backwards after the ignition key has
been removed.
The following options can be selected: 30/
60/90 seconds.
Information
•
The VIN (Vehicle Identification Number)
is the car's unique identity number.
•
Number of Keys The number of keys
registered for the car is displayed here.
Climate functions
Auto blower adjust (Automatic fan
adjustment)
The fan speed can be set to AUTO mode in
cars that have ECC:
•
Select between Low, Normal and High.
Recirculation timer
When the timer is active, the air recirculates
in the car for 3-12 minutes depending on the
outside temperature.
•
58
Select On/Off depending on whether
the recirculation timer should be active
or not.
Reset to factory settings
Resetting the climate function options to
factory settings.
Climate control
Climate control
General information about climate control
Manual climate control, Air conditioning
Electronic climate control, ECC (option)
Air distribution
Fuel driven heater (option)
Additional heater (diesel)
60
62
64
67
68
70
59
Climate control
General information about climate control
Air conditioning – A/C
Refrigerant
The climate control system cools or heats
and dehumidifies the air in the passenger
compartment. The car has either manual
(MCC) or automatic (ECC) climate control.
Refrigerant R134a is in the air conditioning
system. This contains no chlorine, which
means it is harmless to the ozone layer. Only
use R134a when filling/changing refrigerant.
Have a Volvo workshop carry out this work.
NOTE! The air conditioning can be switched
off, but for optimal air quality in the passenger
compartment and to prevent the windows
from misting it should always be on (even at
temperatures of 0-15°C.).
Misting on window interiors
Reduce the problem of fogging by wiping the
inside of the windows. Use a normal window
cleaner.
Ice and snow
Remove ice and snow from the climate
control air intake (the grille between the
bonnet and the windscreen).
Fault tracing
Your Volvo workshop has the instruments
and tools required for any fault tracing or
repair of your climate control system. Entrust
checks and repairs only to trained personnel.
60
Passenger compartment filter
All air which enters the passenger
compartment is cleaned by a filter. This must
be regularly replaced. Follow the Volvo
Service Programme for the recommended
replacement interval. If the car is used in a
severely contaminated environment, it may be
necessary to replace the filter more often.
NOTE! There are two different types of
passenger compartment ventilation filter.
Ensure that the correct filter is installed.
Air vents in the dashboard
Display
C. Lateral airflow
There is a display above the climate control
panel. This is where the climate settings are
displayed.
Personal preferences
The climate control system can be set to two
functions:
• Fan speed to AUTO mode (only applies
to cars with ECC).
• Timer controlled recirculation of the air
in the passenger compartment.
For information about settings see page 57 .
A. Open
B. Closed
D. Vertical airflow.
Aim the outer vents towards the front side
windows to remove misting.
Cold climates: Close the centre vents for the
most comfortable climate and best
demisting.
Climate control
ECC (option)
Actual temperature
The temperature you select corresponds to
the physical experience with reference to air
speed, humidity, exposure to sun, etc. which
affect the interior and exterior of the car.
Condensation
In warm weather, condensation from the air
conditioning system may drip under the car.
This is normal.
Sensor placement:
• The sun sensor is on the upper side of
the dashboard.
•
The temperature sensor for the
passenger compartment is behind the
climate control panel.
NOTE! Do not cover or block the sensors
with clothing or other objects.
Side windows and sunroof
To ensure that the air conditioning works
satisfactorily, close all the side windows and
the sunroof.
NOTE! Do not obstruct the ventilation holes
for the cargo compartment in the parcel shelf
with clothing or other objects.
Acceleration
The air conditioning system switches off
temporarily during full acceleration. You may
feel a temporary rise in temperature.
61
Climate control
Manual climate control, Air conditioning
car when this function is activated.
Recirculation (together with the air
conditioning system) cools the passenger
compartment more quickly in a warm climate.
If the air in the car recirculates for too long,
there is a risk of misting on the insides of the
windows.
Control panel
Functions
1.
Fan
2.
Recirculation
3.
Defroster
1. Fan
Reduce the fan speed by
turning the knob.
If the knob is turned
anticlockwise and the fan
indication in the display
goes out, the fan and the air conditioning are
switched off. The display shows the fan
symbol and OFF.
4.
A/C - On/Off
5.
Airflow to the floor
6.
Airflow to head and body
7.
Airflow to the windscreen
8.
Heated front left seat
9.
Heated front right seat
10. Rear window and door mirror defrosters
11. Temperature selector
62
2. Recirculation
Recirculation can be used
to shut out bad air, exhaust,
etc. from the passenger
compartment. The air in the
passenger compartment is
recirculated. No outside air is taken into the
Timer
The timer function minimises the risk of ice,
misting and bad air - when the recirculation
function is selected. See the “Personal
preferences” section page 58 to activate/
deactivate the function. Recirculation is
always disengaged when you select
Defroster (3).
•
3. Defroster
Defroster is used to quickly
remove misting and ice
from the windscreen and
side windows.
Air flows to the windows at high fan
speed.
•
The LED in the defroster button lights
when this function is activated. The air
conditioning system is controlled so that
there is maximum air dehumidification.
•
The air is not recirculated.
Climate control
4. A/C - On/Off
ON: Air conditioning is
connected.
OFF: Air conditioning (A/
C) system disconnected. If
Defroster (3) is activated
the air conditioning is
always engaged.
Manually selected airflow
Press one of the three buttons (5), (6) or (7).
Selected airflow is opened completely. A
symbol in the display above the climate
control panel and a lit LED in the relevant
button indicate that manual function has been
selected.
5. Airflow to the floor
Air to legs and feet.
6. Airflow to the head
and chest
7. Airflow to the
windscreen and side
windows
11. Temperature
selector
Select cooling or heating
for both the driver's and
passenger sides.
8 and 9. Heated front
seats
(option in certain markets)
Higher heat
level
Lower heat
level
Heat off
Press the button once
- both LEDs light.
Press the button twice
- one LED lights.
Press the button three
times - no LEDs are lit.
10. Rear window and
door mirror defrosters
Heating is used to quickly
remove misting and ice
from the rear windscreen
and door mirrors.
63
Climate control
Electronic climate control, ECC (option)
manual functions, the other functions
continue to be controlled automatically. All
manual settings are switched off when AUTO
is switched on. The display shows AUTO
CLIMATE.
2. Fan
Fan speed can be
increased or decreased by
turning the knob. The fan
speed is regulated
automatically if AUTO is
selected. The previously
set fan speed is
disconnected.
1.
Auto -On/Off
11. Rear window and door mirror defrosters
2.
Fan
12. Temperature selector
NOTE! If the knob is turned anticlockwise
and the fan indication in the display goes out,
the fan and the air conditioning are switched
off. The display shows the fan symbol and
OFF.
3.
Recirculation
Functions
3. Recirculation
4.
Defroster
5.
Airflow to the floor
1. Auto -On/Off
6.
Airflow to head and body
7.
Airflow to the windscreen
This function can be used
to shut out bad air, exhaust
fumes etc. from the
passenger compartment.
The air in the passenger
compartment is
recirculated. No outside air is taken into the
car when this function is activated. If the air in
8.
ECC - ON/OFF
9.
Heated front seat, left
10. Heated front seat, right
64
The AUTO function
automatically regulates
climate control so that the
desired temperature is
attained. The automatic
function controls heating,
air conditioning, fan speed, recirculation, and
air distribution. If you select one or more
Climate control
the car recirculates for too long, there is a risk
of misting on the insides of the windows.
Select one of the following three functions by
pressing the recirculation button repeatedly.
Timer
The timer function minimises the risk of ice,
misting and bad air - when the recirculation
function is selected. See the “Personal
preferences” section to activate/deactivate
the function.
•
The air quality sensor is active - the LED
(A) lights.
•
Recirculation is not activated unless
required for cooling in a warm climate no LED is lit.
•
Recirculation is active - the LED (M)
lights.
NOTE! Recirculation is always disengaged
when you select Defroster (4).
3. Air quality system (option)
(same button as recirculation)
The air quality system
consists of a multifilter and
a sensor. The filter
separates gases and
particles, reducing odour
and contaminants in the
passenger compartment. The air intake is
shut and the air is recirculated in the
passenger compartment if the sensor
detects contaminated outside air. When the
air quality sensor is active, the green LED (A)
in the button lights.
Activate the air quality sensor:
• Press the AUTO button (1) to activate
the air quality sensor (normal setting).
Or:
controlled so that there is maximum air
dehumidification. The air is not recirculated.
5. Airflow to the floor
Air to the legs and feet
6. Airflow to the head and chest
Tip!
• Have the air quality sensor connected.
•
Recirculation is limited in cold climates
to avoid misting.
•
The air quality sensor should be
deactivated if the windows begin to
mist.
•
If there is misting, use the defrosters for
the windscreen, rear windscreen and
side windows.
7. Air to the windscreen and side
windows
4. Defroster
Defroster is used to quickly
remove misting and ice
from the windscreen and
side windows. Air flows to
the windows at high fan
speed. The LED in the
defroster button lights when this function is
activated. The air conditioning system is
65
Climate control
8. ECC ON/OFF
The air conditioning
system is controlled
automatically by the
system when the ON LED
is lit. This way, incoming air
is cooled and dehumidified
sufficiently. The air conditioning (A/C) system
is disengaged when the OFF LED lights.
Other functions are still controlled
automatically. When Defroster (4) is
selected, the air conditioning system is set for
maximum dehumidifying.
9 and 10. Heated front seats
(option in certain markets)
To heat the front seat:
Higher heat
level
Lower heat
level
Heat off
66
Press the button once
- both LEDs light.
Press the button twice
- one LED lights.
Press the button three
times - no LEDs are lit.
11. Rear windscreen and door mirror
defrosters
Use the defroster to
remove ice and misting
from the rear window and
door mirrors.
The rear window and door mirrors are
defrosted simultaneously if the switch is
pressed once. The function is active if one
LED is lit in the switch. The door mirrors are
deactivated automatically after approximately
6 minutes. The rear windscreen is
deactivated after approximately 12 minutes.
12. Temperature selector
The temperatures on the
driver and passenger sides
can be set independently.
Both sides are activated when the car is
started. Only one side is activated if the
button is pressed once. If pressed again, only
the other side is activated. Both sides are
activated again if the button is pressed a third
time. The active side is indicated by an LED
in the button and in the display above the
climate control panel.
NOTE! Heating or cooling cannot be
hastened by selecting a higher or lower
temperature than the actual desired
temperature.
Climate control
Air distribution
Air distribution
Air distribution
Air to windows. There is
a certain amount of
airflow to the air vents.
The air is not
recirculated. Air
conditioning is always
connected.
Air to windows.
Use:
to remove ice and
misting quickly.
Air distribution
Air to the floor and
windows. There is a
certain amount of
airflow to the air vents.
Use:
to ensure
comfortable
conditions and good
demisting in a cold or
humid climate.
to ensure efficient
cooling in a warm
climate. Prevents
misting and icing in
a cold climate.
Air to the floor and air
vents.
in sunny weather
with cool outside
temperatures.
Air to the windows and
dashboard air vents.
to ensure good
comfort in a warm
and dry climate.
Air to the floor. There is
a certain amount of
airflow to the air vents
and windows.
to warm the feet.
Air to the dashboard air
vents.
to ensure efficient
cooling in a warm
climate.
67
Climate control
Fuel driven heater (option)
Activating the heater
Immediate stop of heater
1.
1.
Use the thumb wheel to scroll to
“DIRECT START”.
2.
Press the RESET button (C) to make
ON and OFF selections available.
3.
Select OFF.
2.
Enter the time when the car is to be
used. Press RESET (C) to enter the
hours and minutes when the car is to be
used.
Press RESET again. The timer is
activated.
Press RESET button to activate the Timer.
• The timer is activated: ON lamp lights
with a steady glow.
•
General information about
heaters
The parking heater can be started
immediately or set with two different start
times using TIMER 1 and TIMER 2. Here,
start time refers to the time the car should be
heated and ready. The car’s electronic
system calculates when heating should be
started based on the outside temperature.
There will be no heating if the outdoor
temperature exceeds 25°C. At temperatures
of –7°C and below, the maximum running
time of the parking heater is 60 minutes.
WARNING!
The car must be outdoors if using petrol
and diesel heaters.
68
The heater operates: ON lamp flashes.
Parking on a hill
If the car is parked on a steep incline, the
front of the car should point downhill to
ensure that there is a
supply of fuel to the parking heater.
Heater direct start
1.
Use the thumb wheel (B) to scroll to
“DIRECT START”.
2.
Press the RESET button (C) to make
ON and OFF selections available.
3.
Select ON.
The heater will now run for 60 minutes.
The passenger compartment will begin
to heat up as soon as the engine
coolant has reached a temperature of
38°C
Battery and fuel
If the battery is not sufficiently charged or the
petrol level is too low, the parking heater will
be switched off automatically. A message
appears in the information display. Confirm
the message by pressing the READ button
(A).
IMPORTANT!
Repeated use of the parking heater
combined with short journeys may
discharge the battery and impair starting.
In order to ensure that the generator has
time to produce the energy required by
the heater without discharging the battery,
if the heater is used regularly the car must
be driven for a period equalling the time
during which the heater has been active.
Climate control
Setting TIMER 1 and 2
For reasons of safety, you can only
programme times for the following 24 hours,
not several days in a row.
1.
Use the thumb wheel to scroll to TIMER
2. Press the RESET button briefly to select
the flashing hours setting.
3.
which timer is active when the driver removes
the key from the ignition and is leaving the
car.
Car clock/timer
If the car clock is reset after the clocks in the
heater are programmed, the selected times
will be cancelled for safety reasons.
Use the thumb wheel to scroll to the
required hours.
4. Press the RESET button briefly to select
the minutes setting.
5.
Use the thumb wheel to set the desired
minutes.
6.
Press the RESET button briefly to
confirm the setting.
7.
Press the RESET button to activate the
timer.
Once TIMER 1 has been set, a second start
time can be programmed in TIMER 2 which
is accessed using the thumb wheel. The
alternative start time is set in the same way
as with TIMER 1.
Messages in the display
Once the TIMER 1, TIMER 2 and Immediate
start settings are activated, the information
symbol in the combined instrument panel
lights and an explanatory text is shown in the
information display. The display indicates
69
Climate control
Additional heater (diesel)
WARNING!
• Switch off the fuel driven heater before
beginning refuelling.
• Spilled fuel could be ignited by the
exhaust gases.
• Check in the information display that
the heater is off.
Additional heater
Manual shut off
(certain markets)
In certain situations it may be desirable to be
able to switch off the additional heater, such
as when refuelling.
• Press the READ button (A) once. The
heater switches off and FUEL HEATER
OFF is displayed.
In certain conditions, diesel cars may require
extra heating to ensure sufficient heating in
the passenger compartment. The additional
heater is fully automatic and only starts when
it is sufficiently cold.
When the additional heater is
running, it is indicated by an
information symbol on the
dashboard, combined with FUEL
HEATER ON, which flashes in
the display above the dashboard.
70
Interior
Interior
Front seats
Interior lighting
Storage compartments in the passenger
compartment
Rear seat
Cargo compartment
Warning triangle
72
74
76
78
80
81
71
Interior
Front seats
5.
Change the angle of the backrest, turn
the knob
6.
Control panel for power seats.
Position controls (2) and (3) are not fitted to
all seat models.
WARNING!
• Adjust the driver's seat position before
driving, never while driving.
• Check that the seat is locked in
position.
Seating position
The driver and passenger seats can be
adjusted to the optimum sitting and driving
positions.
1.
Forwards/backwards, lift the handle to
set the correct distance to the steering
wheels and pedals. Check that the seat
has locked into position after adjusting.
2.
Raise/lower the front edge of the seat
cushion, pump up or down (option)
3.
Raise/lower the seat, pump up or down
(option)
4.
Change the lumbar support, turn the
knob
72
Position controls (2) and (3) are not fitted to
all seat models
Lowering the front seat backrest
(option)
The passenger seat backrest can be folded
forwards to make room for long loads.
1.
Move the seat as far back as possible.
2.
Set the backrest to 90°, the upright
position.
3.
Lift the catches on the rear of the
backrest whilst folding it forwards.
Interior
the driver’s door is opened within 2 minutes,
the driver’s seat will assume the stored
position.
Seats with memory function (option)
1. Seat setting, program 1
Power seat (option)
Preparations
The seat can normally only be adjusted if the
ignition - key is in position I or II. It can also be
adjusted within 10 minutes of the door being
unlocked with the key or remote control. If the
door is closed and the ignition key is not yet
in the ignition, or the ignition is in position 0,
settings can be made within 40 seconds of
the door being closed.
Memory function in the remote control
(option)
The remote control used to unlock the car
stores information about the seat settings
which are changed. The next time the car is
unlocked using the same remote control and
2.
Seat setting, program 2
3.
Seat setting, program 3
4.
Storing seat settings
Three positions can be stored. After setting
the seat, hold the M button (4) pressed in
while pressing button (1). Further seat
settings can be stored in the memory using
the memory buttons (2) and (3).
Setting preset positions
Hold memory button (1), (2) or (3) pressed
until the seat stops. For safety reasons, the
seat will stop moving immediately if the
button is released.
blocked by any object. If this occurs, switch
off the ignition (key in position 0) and wait
about 20 seconds before using the seat
again.
Emergency stop
If the seat accidentally begins to move, press
one of the buttons to stop the seat.
WARNING!
• Ensure that there are no obstructions
in front of, behind or underneath the
seat when setting the position.
• Ensure that none of the rear seat
passengers will be trapped.
• To avoid injury, ensure that children
do not play with the switches.
Seat adjustment
The following can be set using the two
switches (5), (6) and (7):
5.
Backrest rake
6.
Seat forwards/backwards and up/down
7.
Front edge of seat cushion up/down
Only one of the electric motors can be
operated at a time. The power seats have an
overload protector that activates if a seat is
73
Interior
Interior lighting
Automatic lighting
The interior lighting comes on and goes out
automatically when the switch (B), see the
illustration, is in the neutral position.
The lighting comes on and remains lit for 30
seconds when:
•
the car is unlocked from the outside
using the key or remote control.
•
the engine is stopped and the ignition
key is turned to the 0 position.
The lighting comes on and remains lit for five
seconds when:
A. Lighting left-hand side. B. Switch.
C. Lighting right-hand side
Lighting front seat
The lighting in the front section of the
passenger compartment can be controlled
using the buttons in the roof console.
Three positions can be selected for lighting
the entire passenger compartment using
switch (B)
1. Off - left-hand side pressed, passenger
lighting off.
2. Neutral position - passenger
compartment lighting lit when a door is
opened and goes out when the door is
closed. The dimmer function is active.
3. On - right-hand side pressed, passenger
lighting lit.
74
•
one of the doors is open
•
the lighting is not switched off.
The interior lighting goes out when:
•
the engine is started
•
the car is locked from the outside using
the key or remote control.
The interior lighting goes out automatically
five minutes after the engine is switched off.
The interior lighting can be switched on or off
within 30 minutes of the key being turned to
position 0 by pressing the button (B) briefly.
The programmed times can be changed. See
the instructions in the section about
“Personal preferences” page 57 .
Lighting rear seat
Lamps can be switched on or off by pressing
the respective button. The lighting goes out
automatically ten minutes after the engine is
switched off.
Interior
Vanity mirror
The lamp comes on automatically when the
cover is lifted.
75
Interior
Storage compartments in the passenger compartment
76
Interior
1.
Centre console locker (also at the front
edge of the front seat, seat cushions.)
2.
Door panel compartment
3.
Ticket clip.
4.
Glovebox.
5.
Waste basket (accessory).
6.
Storage compartment and cup holder.
7.
Storage compartment and cup holder.
WARNING!
Waste paper basket (5) must not be
installed if the handset is mounted on the
right hand side of the centre console.
WARNING!
• Make sure that no hard, sharp or heavy
objects lie or protrude in such a way
that they could cause injuries during
heavy braking.
• Always secure large, heavy loads
with one of the seat belts or a
retaining strap.
Glovebox
The owners manual and maps can be stored
here. There are also holders for coins, pens
and fuel cards. The glovebox can only be
locked and unlocked using the detachable
key blade on the remote control. See the
Lock and Alarm section page 84 for further
information about the key.
Floor mats (option)
Volvo offers floor mats specially
manufactured for your car. They must be
firmly secured in the clips on the floor so that
they cannot slide and become trapped under
the pedals on the driver's side.
77
Interior
Rear seat
IMPORTANT!
The head restraints can be damaged if
they are not removed when loading. The
centre head restraint must be removed
when transporting heavy loads.
Adjust the head restraint vertically
Hanging up seat belts
Rear centre seat head restraint
Tipping the rear seat backrest
All the head restraints can be adjusted
vertically to suit the height of the passenger.
The upper edge of the head restraint should
be aligned to the centre of the rear of the
head. Slide the head restraint up as desired.
Press the button on the right hand pillar of the
head restraint while pushing down to return
the head restraint to the down position. Press
the button on the right hand pillar of the head
restraint while pulling upwards to remove the
head restraint.
The rear seat backrests can be folded
forwards, either together or individually, to
make it easier to transport long objects. To
avoid damaging the seat belts when folding
the backrest up or down, they must be hung
on the grab handle hook.
78
•
Hang the seat belt up before folding the
backrests up or down.
Interior
NOTE! The red indicator must not be visible
when the backrest is folded back into the
upright position. The backrest is not secure if
still visible.
WARNING!
Do not forget to remove the seat belt
from the hooks again when backrest has
been folded up.
Folding the backrest
1.
Pull the straps to fold the seat cushions
forwards.
2.
Pull the latches up and forward to
detach the backrest. A red mark on the
latches indicates that the backrest is not
in the locked position
3.
Fold the backrest halfway forward and
remove the outer head restraints. The
head restraint in the centre seat must be
pressed down fully or removed
4.
Place the head restraints in the plastic
sleeves on the bottom of the folded seat
cushions.
79
Interior
Cargo compartment
Load retaining eyelets
The load retaining eyelets are used to secure
the restraining strap or net holding goods in
the cargo compartment.
80
Electric socket, cargo
compartment (option)
Fold down the cover to access the electric
socket. This operates regardless of whether
the ignition is switched on or not.
If the ignition is switched off and load with a
power consumption higher than 0.1 A is
connected to the electric socket, a warning
message appears in the information display.
The maximum current for the electrical socket
is 15A. Remember not to use the electrical
socket when the ignition is switched off.
There is a risk of the battery being
discharged.
Grocery bag holder (option)
The grocery bag holder holds bags in place
and prevents them tipping over and spilling
their contents in the cargo compartment.
Interior
Warning triangle
location that is appropriate for the traffic
situation.
After use:
1. Reinstall everything in reverse order.
2.
Make sure the warning triangle and its
case are properly secured in the cargo
compartment.
Setting up the warning triangle1
Follow the applicable regulations for the use
of warning triangles.
1.
Release the cover containing the
warning triangle. It is secured with
Velcro.
2.
Remove the warning triangle from its
case (A).
3.
Fold out the four support legs on the
warning triangle.
4.
Fold out both red sides of the warning
triangle. Place the warning triangle in a
1
Certain markets
81
Interior
82
Locks and alarm
Locks and alarm
Remote control with key blade
Locking and unlocking
Child safety locks
Alarm (option)
84
87
89
90
83
Locks and alarm
Remote control with key blade
Remote control
seconds. To set the desired timer
setting, see page 58 .
The car is supplied with two remote controls.
These also work as ignition keys. The remote
controls contain detachable metal key blades
for mechanical locking/unlocking of the
driver's door and glove compartment. A
separate label with the code of the key blade
is supplied. Store the label in a safe place.
Take the label to a Volvo workshop when
ordering new keys. A maximum of six remote
controls/key blades can be programmed and
used for one car.
Boot lid- Press the button once to
unlock the boot lid only.
Loss of a remote control
If either of the remote controls is lost, the
other must be taken with the car to a Volvo
workshop. As a crime prevention measure,
the code of the lost remote control must be
erased from the system.
Immobilizer
The remote controls have coded chips. The
code must match the reader (receiver) in the
ignition switch. The car can only be started if
the correct remote control with the correct
code is used.
IMPORTANT!
Never use force on the narrow section of
the remote control - this is where the chip
is located. The car cannot be started if the
chip is damaged.
84
Remote control functions
Locking - Locks all doors and the boot
lid. A long press also closes the side
windows and sun roof.
Unlocking - Unlocks all doors and the
boot lid. A long press also opens the
side windows.
Approach lighting - As you approach
the car:
Press the yellow button on the remote
control to light the interior lighting,
position/parking lamps, number plate
lighting and the lamps in the door
mirrors (option). The lighting switches
off automatically after 30, 60 or 90
Panic function- Used to attract
attention during emergency situations. If
the red button is held in for at least three
seconds or pressed twice within three
seconds, the direction indicators,
interior lighting and horn will be
activated. This function can be
deactivated using the same button after
it has been active for at least five
seconds. Otherwise it switches off after
30 seconds.
Key blade
This function is intended to be used when
handing over the car for servicing, or valet
parking at a hotel etc. The remote control is
handed over without the detached key blade,
which the owner keeps.
Locks and alarm
5HPRYLQJWKHNH\EODGH
2SHQWKHNH\EODGHRXWRIWKHUHPRWHFRQWURO
f
6OLGHWKHVSULQJORDGHGFDWFKWRWKH
VLGHZKLOVWSXOOLQJWKHNH\EODGHRXW
WRWKHUHDU
,QVWDOOLQJWKHNH\EODGH
%HFDUHIXOZKHQSXWWLQJWKHNH\EODGHEDFN
LQWRWKHUHPRWHFRQWURO
f
/RFNLQJSRLQWVQRUPDOSRVLWLRQ/RFNLQJ
SRLQWVVHUYLFHSRVLWLRQ
f
*HQWO\SUHVVWKHNH\EODGHWRORFNLWLQ
SRVLWLRQ,WZLOOFOLFN
/RFNLQJWKHJORYHER[
7KHNH\EODGHLVXVHGWRORFNRUXQORFNWKH
JORYHER[7KHGULYHU
VGRRUFDQDOVREH
ORFNHGRUXQORFNHGXVLQJWKHNH\EODGH
:HDNEDWWHU\LQWKHUHPRWH
FRQWURO
:KHQWKHEDWWHU\EHJLQVWRUHDFKWKHSRLQW
ZKHUHIXOOIXQFWLRQDOLW\FDQQRWEHJXDUDQWHHG
WKH,QIRUPDWLRQV\PEROOLJKWVDQG5(027(
%$77(5</2:92/7$*(LVVKRZQLQWKH
GLVSOD\
+ROGWKHUHPRWHFRQWUROZLWKWKHSRLQWHG
HQGGRZQ5HOHDVHWKHNH\EODGHLQLWV
JURRYH
85
Locks and alarm
5.
Pry out (2) and change the battery.
Avoid touching the battery and its
contact surfaces with your fingers.
6.
Reinstall and screw the cover into place.
7.
Press the key blade back into position.
Ensure that the old battery is disposed of in
an environmentally friendly way.
Changing the remote control
battery
If the locks repeatedly fail to react to signals
from the remote control at a normal distance,
the battery should be replaced (type CR
2032, 3 volt).
1.
Pull out the key blade.
2.
Place the remote control with the
keypad downwards. Remove the screw
(1) using a small screwdriver.
3.
Remove the cover.
4.
Note how the + and – poles of the
battery are positioned on the inside of
the cover.
86
Locks and alarm
Locking and unlocking
The doors cannot be opened by pulling up
the lock button. All the doors can also be
locked manually using the relevant lock
button. This applies only if the car is not
locked from the outside. The doors can also
be unlocked using the opening handle.
Locking/unlocking from outside
the car
The remote control can be used to lock or
unlock all the car doors and the boot lid at the
same time. The doors can be unlocked using
the detached key blade.
This applies only if the car is not locked from
the outside. The doors can also be unlocked
(and door opened) using the handle.
WARNING!
Note that occupants can be locked
inside the car if it is locked from the
outside.
Automatic re-locking
If none of the doors or the boot lid are opened
within two minutes of unlocking, all locks relock automatically. This function prevents the
car from unintentionally being left unlocked.
For cars with alarms, see the Alarm System
section.
Locking/unlocking from inside
the car
The switches in the door panel can be used
to lock or unlock all the doors and the boot lid
simultaneously.
•
Unlocking:
Press in the upper section in the lock
button. A long press also opens all the
side windows.
•
Locking:
Press in the lower section of the lock
button. A long press also closes all the
side windows and the sun roof.
Opening the boot lid
Carry out the following to unlock the boot lid
only:
•
Press the boot lid button on the remote
control .
If all the doors are locked when the boot lid is
closed, it locks automatically.
87
Locks and alarm
2. Press the button 1.
If the car is equipped with an alarm, the
movement and tilt detectors are also
deactivated. See page page 91.
The LED in the button lights until the car is
locked with the key or remote control. A
message is shown in the display as long as
the key remains in the ignition switch. The
next time the car ignition is switched on, the
sensors will be re-engaged.
WARNING!
1. Disconnecting the sensors. 2. No function.
Locking the glovebox
The glovebox can only be locked and
unlocked using the detachable key blade on
the remote control.
1.
Unlock the glovebox by turning the key a
quarter of a turn (90°) anti-clockwise.
The key hole is vertical when unlocked.
2.
Lock the glove compartment by turning
the key a quarter of a turn (90°)
clockwise. The key hole is horizontal
when locked.
Deadlocks
When deadlocked, the doors cannot be
opened from the inside if they are locked.
88
Activated using the remote control.
Deadlocks are activated after 25 seconds
delay after the doors are locked. The car can
only be deadlocked using the remote control.
The doors can also be opened using the key
from the outside.
Temporary deactivation of
deadlocks and any detectors.
If others prefer to remain seated in the car
with the doors locked from the outside, the
deadlocks can be deactivated.
1.
Insert the key in the ignition switch, turn
it to position II and then back to position
I or 0.
Do not allow anyone to remain in the car
without first deactivating the
deadlocking.
Locks and alarm
Child safety locks
Lock in the window, rear
(option)
When the electric child safety locks are
active, the rear windows cannot be used.
Activate the child safety locks:
1. Turn the ignition key to position I or II.
2. Press the button. The rear windows
cannot be opened when the LED in the
button is lit.
A message will appear in the information
display when the child safety locks are
activated.
Manual lock in the left-hand rear door
Locks in the doors, rear
To lock manually: The controls for the child
safety locks are in the rear edges of the rear
doors and are only accessible when the door
is open. Use the key blade to turn the control
and thus activate or deactivate the child
safety locks.
A: The doors cannot be opened from the
inside.
B: The doors can be opened from the inside.
Electrical lock for opening the rear door and
window
WARNING!
Always keep the lock buttons up when
driving. In the event of an accident,
rescue personnel will then be able to
quickly get into the car. The rear seat
passengers cannot open the doors from
the inside if the child safety locks are
activated.
NOTE! When the electric child safety locks
are activated, the settings made in the
manual child safety system are overwritten.
Child safety locks activated
The LED comes on at the same time as a text
message in the display indicates that the lock
has been activated. The doors cannot be
opened from the inside. The window lift
mechanisms can only be controlled using the
controls on the driver's door.
To lock electronically: Press the controls in
the driver's door. A message appears in the
information display.
89
Locks and alarm
Alarm (option)
The alarm system
workshop.
If the alarm system does not function
correctly, have a Volvo workshop examine the
car.
When the alarm is armed, it continually
monitors all alarm points.
The alarm is triggered if:
•
a door, the bonnet or boot lid is opened
•
the boot lid is opened
•
a non-approved key is used in the
ignition or if an attempt is made to force
the lock
•
movement is detected in the passenger
compartment (if a motion sensor is
fitted)
•
the car is raised or towed away (if a tilt
sensor is fitted)
•
the battery cable is disconnected
•
anyone tries to disconnect the siren.
NOTE! Do not attempt to repair or modify
alarm system components. Any such
attempts may affect the terms of insurance.
Connecting the alarm function
•
Alarm LED in the dashboard
An alarm LED on the dashboard (see the
illustration) shows the status of the alarm
system:
•
Lamp off - the alarm is deactivated.
•
The lamp flashes once a second - the
alarm is activated.
•
The lamp flashes quickly after the alarm
is deactivated and until the ignition is
switched on - the alarm has been
triggered.
A message will appear in the information
display if a fault occurs in the alarm system. If
this should happen, please contact a Volvo
90
Press the LOCK button on the remote
control. A long flash from the car’s
direction indicators confirms that the
alarm is armed and that all doors are
locked.
Disconnecting the alarm
function
•
Press the UNLOCK button on the
remote control. Two short flashes from
the car’s direction indicators confirm
that the alarm has been deactivated and
that all doors are unlocked.
Automatic alarm activation
This function prevents you from accidentally
leaving the car without the alarm on.
If none of the doors or the boot lid are opened
within two minutes of the alarm being
deactivated (and the car was unlocked with
the remote control), the alarm is armed
automatically. The car locks at the same time.
Locks and alarm
Switching off a triggered alarm
•
If the car has deadlocks, these are engaged
at the same time.
Press the UNLOCK button on the
remote control.
Testing the alarmsystem
Two short flashes of the direction indicators
are given as confirmation.
Testing the passenger compartment
motion sensor
1. Open all windows.
Alarm signals
2.
Activate the alarm. The LED flashes
slowly to confirm that the alarm is
armed.
3.
Wait 30 seconds.
4.
Temporary deactivation of
detectors and deadlocks
Test the motion sensor in the passenger
compartment by lifting a bag or similar
from the seat. The alarm should now
sound and flash.
5.
To avoid accidentally triggering the alarm, on
a ferry for example, the motion and tilt
sensors can be temporarily disengaged.
Deactivate the alarm by unlocking with
the remote control.
Testing the doors
1. Activate the alarm.
1.
2.
Wait 30 seconds.
3.
Unlock using the key on the driver’s
side.
4.
Open one of the doors. The alarm
should now sound and flash.
5.
Deactivate the alarm by unlocking with
the remote control.
The following happens if the alarm is
triggered:
•
•
A siren sounds for 30 seconds. It has its
own battery which is engaged if the car
battery has insufficient charge or is
disconnected.
All turn signal lamps flash for five
minutes or until the alarm is switched
off.
Remote control not working
Even if the remote control is not working, the
car can still be started as follows:
1.
2.
Open the driver’s door using the key
blade. The alarm is triggered and the
siren sounds.
Insert the key blade in the remote
control in the ignition. The alarm is
deactivated. The LED flashes rapidly
until the ignition key is turned to position
II.
1. Disconnecting the sensors. 2. No function
2.
Turn the ignition key to position II and
then back to position 0. Remove the key.
Press the button (1). The LED in the
button is lit until the car is locked.
A message remains in the display as long as
the key is in the ignition (or for 1 minute after
the key is removed)
The next time the ignition is switched on, the
sensors will be re-connected.
91
Locks and alarm
Testing the bonnet
1. Get into the car and deactivate the
motion sensor.
2.
Activate the alarm. Remain in the car
and lock the doors with the button on
the remote control.
3.
Wait 30 seconds.
4.
Open the bonnet with the handle under
the dashboard. The alarm should now
sound and flash.
5.
Deactivate the alarm by unlocking with
the remote control.
92
Starting and driving
Starting and driving
General
Refuelling
Starting the car
Manual gearbox
Automatic gearbox (option)
Automatic gearbox (option)
Brake system
Stability system
Towing and transportation
Start assistance
Driving with a trailer
Towing bracket
Detachable towbar
Loading
Adapting light pattern, right and left hand
drive traffic
94
95
96
98
100
101
103
105
107
109
110
112
114
117
118
93
Starting and driving
General
Economical driving
Economical driving results from driving gently
with anticipation and adapting your driving
style and speed to the prevailing conditions.
•
•
•
•
•
•
•
•
Run the engine to operating temperature
as soon as possible.
Do not let the engine idle, but drive at
light load as soon as possible.
A cold engine consumes more fuel than
a warm one.
Avoid unnecessary quick acceleration
and heavy braking.
Do not drive with unnecessary loads in
the car.
Do not use winter tyres on dry roads.
Remove the roof rack when it is not in
use.
Avoid driving with open windows.
Slippery surfaces
Driving on slippery surfaces can be
experienced differently. Practice driving in
mock slippery conditions in order to
determine how the car will react.
Engine and cooling system
Under certain conditions, e.g. when driving in
hilly terrain or with a heavy load, there is a risk
of the engine and cooling system
overheating.
94
Avoid overheating the cooling system
• Drive at low speeds if driving with a
trailer up a long, steep incline.
•
Do not turn the engine off immediately
you stop if the car has been driven hard.
•
Remove any auxiliary lamps from in front
of the grille if driving in extreme high
temperatures.
Do not overload the battery
The electrical functions of the car load the
battery to varying degrees. Avoid leaving the
ignition key in position II when the engine is
switched off. Use position I instead. Less
power will then be consumed. Remove the
key if no functions are required. Less power
will then be consumed.
Avoid overheating the engine
• Do not drive the car above 4500 rpm
when towing a trailer or caravan in hilly
areas. The oil temperature may rise too
high.
NOTE! The 12 volt socket in the cargo
compartment provides voltage even when
the ignition key has been removed.
Examples of functions that draw a lot of
current are:
Open boot lid
•
blower fan
Avoid driving with an open boot lid. If you
must drive a short distance with the boot lid
open, do as follows:
•
windscreen wipers
•
audio equipment (high volume)
•
parking lamps
•
Close all windows.
•
Distribute the air between the
windscreen and floor and run the fan at
high speed.
Be aware of different accessories that load
the electrical system. Do not use functions
that draw a lot of current when the engine is
switched off.
If the battery charge is low, a message is
shown in the display. Charge the battery by
starting the engine.
WARNING!
Do not drive with an open boot lid.
Poisonous exhaust gases could be
drawn into the car via the cargo
compartment.
Starting and driving
Refuelling
Fuel cap
The fuel cap is inside the fuel filler flap on the
right rear wing.
There may be overpressure in the tank if
outdoor temperatures are high. Do not overfill
the fuel tank.
Reinstall the cap after refuelling. Turn until a
click is heard.
Fuel driven heater (option)
WARNING!
Switch off the fuel driven heater before
refuelling.
Opening the fuel filler flap
The fuel tank filler flap is unlocked and
opened using the central button under the
light switch on the dashboard. The flap is
folded out.
Closing
Press the flap into the body until it clicks.
Emergency opening
If the flap does not open, it can be opened
manually from inside the cargo compartment.
Once the interior upholstery is moved to one
side, there is a handle visible by the lock
mechanism for the flap. Pull it straight back.
Switch off the fuel driven heater before
beginning refuelling.
Spilled fuel could be ignited by the
exhaust gases.
Filling with petrol
IMPORTANT!
Petrol engine cars must always be
refuelled with unleaded petrol to prevent
damage to the catalytic converter.
IMPORTANT!
Do not add any cleaning agents to the
petrol, unless recommended by Volvo.
WARNING!
Never carry a switched on mobile phone
when refuelling. The ring tone can
generate sparks, igniting the fuel
vapours. This could cause a fire and
result in injury.
Filling with diesel
At low temperatures, paraffin can precipitate
out of diesel fuel (–5°C- –40°C). This can
cause problems when starting.
IMPORTANT!
Use special winter fuel during the cold
season.
95
Starting and driving
Starting the car
Depending on the engine temperature when
starting, the engine speed after a cold start
may be higher than normal for certain engine
types. Volvo strives to minimise exhaust
emissions by having the engine exhaust
system reach the correct operating
temperature as quickly as possible.
NOTE! Never rev the engine hard
immediately after a cold start.
Contact a Volvo workshop if the engine
does not start or misfires.
WARNING!
Never remove the ignition key from the
steering wheel lock while driving or while
the car is being towed. Never switch off
the ignition or remove the ignition key
while the car is moving. This could
engage the steering wheel lock, making
the car impossible to steer.
Start petrol engines as follows
1. Apply the handbrake.
2. Automatic gearbox:
Move the gear selector to position P or N.
96
Manual gearbox:
Move the gear lever to neutral and hold
the clutch pedal completely depressed.
This is especially important in severe
cold.
3. Turn the ignition key to the start position.
If the engine does not start within 5-10
seconds, release the key and try again.
The electronic immobilizer could be activated
by accident.
Ignition switch and steering
wheel lock
0 – Locked position
The steering wheel lock
engages when the key is
removed from the ignition.
Start diesel engines as follows
1. Apply the handbrake.
2. Automatic gearbox:
Move the gear selector to position P or
N.
Manual gearbox:
Move the gear lever to neutral and hold
the clutch pedal completely depressed.
This is especially important in severe
cold.
3. Turn the ignition key to the drive position.
A lamp on the combined instrument
panel will come on indicating that the
engine preheater is activated. Turn the
key to the start position when the lamp
extinguishes.
Ignition keys and immobilizer
The ignition key must not hang next to other
keys or metal objects on the same key ring.
I – Radio position
Certain electrical
components can be
switched on. The engine
electrical system is not
connected.
II – Driving position
The key position when
driving. The car’s electrical
system is connected.
III – Start position
The starter motor engages.
Release the key once the
engine has started. The key
automatically springs back to
the driving position.
Starting and driving
If the front wheels are be turned in such a way
that there is tension in the steering wheel lock
a warning message is displayed and the car
cannot be started. Remove the ignition key,
turn the steering wheel so that the steering
wheel lock is released. Insert the key and
make a new start attempt. Make sure the
steering wheel lock is engaged when leaving
the car. This reduces the risk of theft.
WARNING!
• Never remove the ignition key from the
ignition while driving or while the car is
being towed. The steering wheel lock
will engage and it will be impossible to
steer the car.
• Always remove the ignition key from
the ignition when leaving the car,
especially if there are children in the
car.
97
Starting and driving
Manual gearbox
Gear positions, five speed
Depress the clutch pedal fully with each gear
change. Remove your foot from the clutch
pedal between gear changes. Follow the
appropriate shifting pattern.
Use the higher gears as often as possible to
achieve the best possible fuel economy.
98
Reverse gear inhibitor
Only engage reverse gear when the car is
stationary. The gear selector lever must first
be moved to neutral N before reverse gear
can be engaged. Reverse cannot be directly
selected from fifth gear due to the reverse
gear inhibitor.
Gear positions, six speed
(petrol)
Depress the clutch pedal fully with each gear
change. Remove your foot from the clutch
pedal between gear changes. Follow the
appropriate shifting pattern.
Use the higher gears as often as possible to
achieve the best possible fuel economy.
Starting and driving
Reverse gear inhibitor
Only engage reverse gear when the car is
stationary. The gear selector lever must first
be moved to neutral N before reverse gear
can be engaged. Reverse cannot be directly
selected from fifth gear due to the reverse
gear inhibitor.
Gear positions, six speed
(diesel)
Depress the clutch pedal fully with each gear
change. Remove your foot from the clutch
pedal between gear changes. Follow the
appropriate shifting pattern.
Use the higher gears as often as possible to
achieve the best possible fuel economy.
Reverse gear inhibitor
Only engage reverse gear when the car is
stationary. The gear selector lever must first
be moved to neutral N before reverse gear
can be engaged. Reverse cannot be directly
selected from second gear due to the reverse
gear inhibitor.
99
Starting and driving
Automatic gearbox (option)
Cold start
When starting in low temperatures, shifting
may feel harder. This is due to the viscosity of
the gearbox oil at low temperatures. To
minimise engine emissions, the gearbox
shifts up later than normal if the engine has
been started at low temperature.
NOTE! Depending on the engine
temperature when starting, the engine speed
after a cold start may be higher than normal
for certain engine types.
Turbo engine
When the engine is cold, the transmission
shifts gears at higher engine speeds than
normal. This is to help the catalytic converter
reach normal operating temperature faster
with less exhaust emission.
Adaptive system
The gearbox is controlled by what is known
as an adaptive system. The control module
continually " learns " how the gearbox
behaves. It senses how the gearbox shifts
gears and achieves optimal gear shifts each
time. The control module also senses driving
behaviour, such as how hard the driver
depresses the accelerator, and adjusts the
sensitivity of the shift schedule to a driving
style. The gears have a Lock-up function
100
(locked gears) which provides better engine
braking and lowerfuel consumption.
Safety systems
Cars with automatic gearboxes have special
safety systems:
Keylock
The gear selector must be in position P
before the key can be removed from the
ignition. The key is blocked in all other
positions.
Parking position (P)
Stationary car with the engine running:
•
Hold your foot on the brake pedal when
moving the gear selector to another
position.
Shiftlock
The ignition key must be in position II and the
brake pedal pressed before the gearshift can
be moved from position P.
Disengaging the shift lock
In certain cases it may be necessary to move
the car when it is not driveable, for example if
the battery is discharged. Carry out the
following to move the car:
1.
There is a small cover behind P-R-N-D
on the gear selector panel. Open the
rear edge of the panel.
2.
Insert a screwdriver or similar to the
bottom whilst pressing the lever out of
the P position.
Neutral (N)
If the car has been stationary for more than 5
seconds, the ignition key must be in position
II and the brake pedal pressed before the
gear selector can be moved from N.
Starting and driving
N - Neutral
N is the neutral position. The engine can be
started, but no gear is selected. Apply the
handbrake when the car is stationary with the
gear lever in N.
D – Drive
D is the normal driving position. The car
automatically shifts between the different
gears of the gearbox based on the level of
acceleration and speed. The car must be
stationary when selecting position D from
position R.
Manual positions
Gear selector inhibitor
Automatic gear positions
The gear lever can be moved freely forwards
or backwards between N and D. Other
positions are locked with a latch which is
operated by the inhibitor button on the gear
selector. The lever can only be moved when
the engine is running.
Press the inhibitor button to move the gear
selector lever forwards or backwards
between R , N and D .
P - Parking position
Select P position when you wish to start the
engine or park the car.
IMPORTANT!
The car must be stationary when selecting
position P.
In P, the gearbox is mechanically blocked.
Always apply the handbrake when parking.
R - Reverse
The car must be stationary when selecting
position R.
To move from automatic mode D to a manual
position, press the gear selector to the right.
To move from MAN to automatic position D,
press the gear selector to the left to D.
While driving
Manual gearshift mode can be selected at
anytime whilst driving. The engaged gear is
locked until you another gear is selected. The
car will only shift down automatically if you
slow to a very low speed.
If the gear selector is moved to – (minus), the
car downshifts automatically one gear at a
time while engine braking. If the gear selector
is moved to plus (+), the car shifts up one
gear.
101
Starting and driving
W – Winter
Use the button to engage or disengage the
winter program W. The program is activated
if an LED is lit in the button. The winter
program makes it easier to drive at low
speeds in slippery road conditions. When the
program is engaged, the driving wheels
utilise less power than normal and all
upshifting occurs at a lower engine rpm.
NOTE! The winter program W cannot be
engaged if a manual position is selected – it
can only be selected in position D.
Kick-down
When the accelerator pedal is pressed all the
way down, beyond the position normally
regarded as full acceleration, a lower gear is
immediately engaged. This is called kickdown.
When maximum speed for that gear is
reached or the accelerator pedal is released
from the kick-down position, there is an
automatic upshift.
Kick-down should be used when maximum
acceleration is required, for example during
overtaking. The function can only be used
when the gear selector is in automatic
position D.
102
Starting and driving
Brake system
If the brake servo is not working
If the car is rolling or being towed with the
engine switched off, approximately 5 times
more pressure must be applied to the brake
pedal than when the engine is running. The
brake pedal feels rigid and hard when the
brake servo is not operating.
WARNING!
The brake servo only works when the
engine is running.
Brake circuits
The symbol lights if a brake circuit
is not working
Braking is still possible if a fault occurs in one
of the circuits. Press the pedal hard once.
The brake pedal takes longer to press down
and feels softer than normal. The pedal needs
to be pressed harder for normal braking
power.
NOTE! When braking with the engine
switched off, press the brake pedal once
hard and distinctly, not repeatedly.
Dampness can affect braking
characteristics
Brake components become wet when the car
is driven in heavy rain or through pools of
water or when washing the car. The friction
characteristic of the brake pads may change,
reducing braking power.
• Gently press the brake pedal
occasionally if driving longer distances in
rain or slush and after starting in
extremely damp or cold weather. The
brake pads heat up and the water dries.
This action is also advisable before
parking the car for long periods in these
weather conditions.
If the brakes are heavily loaded
When driving in mountains or on other roads
with similar characteristics, the car’s brakes
are heavily loaded even when not pressing
the brake pedal especially hard.
Because speed is often low, the brakes are
not cooled as effectively as when driving on
flat roads.
To ensure that the brakes are not more
heavily loaded than necessary, shift down on
downhill slopes rather than using the brake
pedal. Use the same gear when driving
downhill as you would uphill. This ensures
that engine braking works more efficiently
and brake use will only be necessary for short
periods. Remember that driving with a trailer
further loads the brakes.
Anti-lock braking system (ABS)
The ABS system (Anti-lock Brake
System) prevents the wheels
from locking when braking. This
maintains the ability to steer,
making it easier to avoid
obstacles.
•
After the engine has started and reached
a speed of about 20 km/h (12mph),
there is a short self-test of the ABS
system. This can be both heard and felt
as pulses in the brake pedal.
To fully utilise the ABS system:
•
Press the brake pedal with maximum
force. Pulses will be felt.
•
Steer the car in the direction of travel. Do
not reduce the pedal pressure.
Practice braking with the ABS system in a
traffic free area and in different weather
conditions.
The ABS symbol lights and remains on:
•
for approximately two seconds before
the car starts
•
if the ABS system is disabled due to a
fault
103
Starting and driving
WARNING!
If the BRAKE and ABS warning symbols
light at the same time, there may be a
problem in the brake system. If the brake
fluid level is normal in these
circumstances, drive carefully to the
nearest Volvo workshop to have the
brake system checked.
104
Starting and driving
Stability system
When the stability system is operating it may
seem as if the car does not respond to the
throttle opening. This is because the system
senses the friction of the road surface and
allows the different functions of the stability
system to take effect.
•
The car is either equipped with STC (Stability
and Traction Control) or DSTC (Dynamic
Stability and Traction Control).
Function/
system
TC
SC
AYC
EBA
a
STC
DSTCa
X
X
X
X
X
X
•
Option in certain markets
The Traction Control function transfers
power from the spinning drive wheel to
the drive wheel which has grip. To
increase forward traction in this situation,
you may need to depress the accelerator
more than usual. A pulsing sound is
heard when Traction Control is working.
This is completely normal. The Traction
control function is most active at low
speeds. The function cannot be switched
off.
Spin control Stability control prevents
the driven wheels from slipping on the
road surface during acceleration. This
improves road safety on slippery
surfaces. When driving with snow chains
or in deep snow or sand, it may be
beneficial to switch off the anti-spin
function to increase traction. The
function can be deactivated with the
STC/DSTC button.
•
The Active Yaw Control (AYC)
function automatically brakes one or
more wheels to stabilise the car in the
vent of a skid. The brake pedal is more
rigid than normal and a pulsing sound is
heard while braking.
The Active Yaw Control function is active
at all times. It cannot be switched off.
•
Emergency Brake Assistance - EBA
At hard braking the full brake force is
provided immediately. The system
detects the need for heavier braking by
registering how quickly the brake pedal
is applied. The brake pedal falls when the
system is operating. Continue braking
without releasing the brake pedal. The
function disengages when the pressure
on the brake pedal is released. The
power brake boosting is active at all
times. It cannot be switched off.
105
Starting and driving
Symbols in the centre of the dashboard
•
The symbol lights and goes
out again after approximately
2 seconds
The symbol lights for a system
check when the car is started.
STC or DSTC button
The button in the centre console is used to
deactivate or reactivate the STC (Stability
and traction control)/DSTC (Dynamic
stability and traction control) system. The
LED in the button is lit when the system is
activated. The LED in the button goes out
when the stability system function has
reduced. Other functions are not affected.
NOTE! Press the button for at least half a
second in order to deactivate the STC
(Stability and traction control)/DSTC
(Dynamic stability and traction control)
function. The LED in the button goes out and
the text STC/DSTC SPIN CONTROL OFF is
shown in the display. The system is
automatically reactivated each time the
engine is started.
106
Flashing warning symbol
The stability control function
prevents the car’s drive wheels
from spinning. The traction control
function works to improve the car’s
traction. The active yaw control (AYC)
function works to keep the car from skidding.
The information symbol lights
with a constant light
STC/DSTC SPIN CONTROL
OFF appears in the information
display with the symbol.
•
The Spin Control function has been
deactivated using the STC/DSTC button.
The information symbol lights
with a constant light
TRACTION CONTROL
TEMPORARILY OFF appears in
the information display with the symbol.
The traction control function has been
temporarily reduced due to high brake
temperature. The function is reactivated
automatically when the brake
temperature returns to normal levels.
The information symbol lights
with a constant light
ANTI-SKID SERVICE REQUIRED
appears in the information display
with the symbol.
•
The STC or DSTC (Dynamic stability and
traction control) system is disabled due
to a fault.
1.
Stop the car in a safe place and switch
off the engine.
2.
Restart the engine.
3.
If the warning symbol remains lit, drive
to a Volvo workshop to have the system
checked.
WARNING!
Keep in mind that the car’s driving
characteristics are altered if you
deactivate the STC or DSTC systems.
Always follow the usual precautions for
safe cornering and driving on slippery
surfaces.
Starting and driving
Towing and transportation
Never tow the car to jump start it
Use a booster battery if the battery is
discharged and the engine will not start. Do
not tow the car to jump start it
IMPORTANT!
The catalytic converter could be damaged
if the car is towed.
Towing
Before towing the car, check the highest
permitted legal speed for towing.
1.
Insert the key in the ignition switch in
position I and unlock the ignition lock so
that the car can be steered. See page
96.
NOTE! The key must remain in the
ignition switch during the towing.
2.
Automatic gearbox: Move the gear
selector to position N.
Manual gearbox: Move the gear lever
to neutral.
3.
Ensure that the towing line is fully
stretched to avoid heavy jerking. Keep
your foot on the brake pedal.
Cars with automatic gearboxes must not be
towed at speeds above 80 km/h (50 mph). It
should not be towed further than 80 km (50
miles).
WARNING!
The steering lock in a car without power
is always activated, and the car cannot
therefore be steered. The steering lock
must be unlocked before starting
towing.
Never remove the ignition key from the
ignition while driving or while the car is
being towed.
WARNING!
The brake servo and power steering do
not work when the engine is off.
Approximately five times more pressure
must be exerted on the brake pedal and
steering is considerably heavier than
usual.
Do not tow a car with an automatic
transmission further than 80 km (50 miles).
Recovery
Cars with automatic gearboxes must not
(unless partially raised) be towed at speeds
above 80 km/h (50 mph). It should not be
towed further than 80 km (50 miles).
Towing eye
Use the towing eye if the car must be towed
on roads. The towing eye is secured in the
outlet on the right hand side of the front or
rear bumper. Installing the towing eye:
1. Take out the towing eye which is under
the floor hatch in the cargo
compartment.
2. Remove the bottom of the cover in the
bumper using a slotted screwdriver or a
large coin.
3.
Screw the towing eye securely into
place up to the flange. Use the wheel
brace to turn the towing eye.
107
Starting and driving
4.
After use, unscrew the towing eye and
place it in the cargo compartment.
Reinstall the cover on the bumper.
IMPORTANT!
The towing eye is only intended for towing
on roads, not for recovery after driving into
a ditch etc. Call professional help for
recovery.
108
Starting and driving
Start assistance
3. If the booster battery is in another car,
stop the engine of that car. Ensure the
cars are not touching.
4. Connect the red start cable between the
positive terminal (1+) of the booster
battery and the positive terminal (2+) of
the second battery.
5. Connect one clamp of the black cable to
the negative terminal of the booster
battery (3–).
6. Connect the other clamp on the black
cable to the ground terminal (4-)
mounted on the upper right-hand spring
strut.
Starting with another battery
If the car battery has discharged, the power
from either a free standing battery or the
battery from another car can be used. Always
check that the clamps on the starting cable
are secure so that there are no sparks during
the start attempt.
When using another battery to assist starting
the following steps are recommended to
prevent the risk of explosion:
1. Turn the ignition key to the 0 position.
2. Ensure that the booster battery has 12
volt current.
WARNING!
The battery can generate oxyhydrogen,
which is highly explosive. A spark, which
can be generated if the jump leads are
incorrectly connected, is sufficient to
explode the battery.
The battery also contains sulphuric acid,
which can cause serious corrosive
damage. If the acid comes into contact
with your eyes, skin or clothes, flush with
large quantities of water. If acid splashes
into your eyes, contact a doctor
immediately.
7. Start the engine of the “booster car”. Let
the engine run for a few minutes at a
speed slightly higher than idle, 1500
rpm.
8. Start the engine of the car with the
discharged battery.
9. Remove the starter cables. First remove
the black cable then remove the red
cable. Ensure that none of the clamps on
the black start cable come into contact
with the battery positive terminal or the
cable connected to the red start cable.
NOTE! Do not touch the terminals during the
start attempt. There is a risk of sparking.
109
Starting and driving
Driving with a trailer
General
•
If the towing bracket is a Volvo factory
installation, the car is delivered with the
necessary equipment to drive with a trailer.
•
The car’s towing bracket must be of an
approved type.
•
If retrofitting, check with your Volvo
dealer to ensure that the car is fully
equipped to drive with a trailer.
•
Increase the tyre pressure to the
recommended pressure for full load. See
the tyre pressure table on the inside of
the fuel filler flap.
•
•
•
•
Clean the tow bar regularly and grease
the connector pin1.
For reasons of safety, you should not
drive faster than 80 km/h (50 mph), even
if the laws of certain countries permit
higher speeds.
•
Do not drive with a heavy trailer when
your car is brand new. Wait until it has
driven at least 1000 km (600 miles).
The maximum permissible weight for a
trailer without brakes is 750 kg (1600
lbs).
•
The gear selector must be in position P
when parking an automatic car with
trailer. Always use the parking brake.
•
If parking a car with a trailer on a steep
incline, place chocks behind the wheels.
The gear selector must be in position P
when parking an automatic car with
trailer. Always use the parking brake
The brakes are loaded much more than
usual on long and steep downhill slopes.
Downshift to a lower gear and adjust
your speed.
•
The engine is loaded more heavily than
usual when driving with a trailer.
1
If the car is driven with a heavy load in a
hot climate, the engine and gearbox may
overheat. If the temperature gauge for
the coolant in the combined instrument
panel enters the red zone, stop and allow
the engine to idle for a few minutes. If the
car overheats, the air conditioning
system may switch off temporarily. The
gearbox reacts with a built-in protection
function. Read the message in the
information display.
Does not apply when using a ball hitch
with vibration damper.
110
Trailer weights
Maximum
permissible trailer
weight for a trailer
with brakes
0 – 1200 kg
(0 - 2650lbs)
1201 – 1500 kg
(2652 – 3300 lbs)
Maximum
ball pressure
50 kg (110 lbs)
75 kg (165 lbs)
NOTE! The above are the highest trailer
weights permitted by Volvo. National
regulations may limit trailer weights and
speeds further. Towbars may be certified for
higher tow weights than the car may tow.
WARNING!
Follow the listed recommendations for
trailer weight. The trailer and car could
otherwise be difficult to control during
avoidance manoeuvres and when
braking.
Starting and driving
Automatic gearbox
Parking on a hill:
• Apply the handbrake.
•
Move the gear selector to P, the parking
position.
Starting on a hill:
• Move the gear selector to D, the drive
position.
•
Release the handbrake.
Steep ascents:
• Select an appropriate gear position
when driving up steep ascents or at low
speed. This prevents the gearbox from
shifting up and the gearbox fluid from
thinning out.
•
Do not use a higher manual gear than the
engine can "handle". It is not always
economical to drive in high gears.
•
Avoid driving with a trailer on inclines
exceeding 15%.
111
Starting and driving
Towing bracket
Towbars
The connector pin must be cleaned and
lubricated with grease regularly. When ball
hitch with vibration damper is used there is
no need to grease the connection pin.
If the car is equipped with a detachable tow
hitch the installation instructions for installing
the connector pin must be followed closely.
See page 114.
WARNING!
Ensure that the trailer's safety cable is
secured to the correct mounting.
WARNING!
If the car is equipped with a Volvo
detachable towbar:
• Follow the installation instructions for
the connector pin carefully.
• The connector pin must be locked by
the key before moving off.
• Check that the indicator window is
showing green.
112
Trailer cable
An adapter is required if the car's towing
bracket has a 13-pin electrical connector and
the trailer has a 7-pin connector. Use a Volvo
approved adapter cable. Make sure that the
cable does not drag on the ground.
Specifications
Distance A
Fixed towbar:
1055 mm (41.5 inches)
Detachable towbar: 1055 mm (41.5 inches)
Maximum ball pressure:
75 kg (165 lbs)
Starting and driving
Distance B
Fixed towbar:
72 mm (2.8 inches)
Detachable towbar:
72 mm (2.8 inches)
113
Starting and driving
Detachable towbar
Installing the connector pin
1.
114
Remove the cover plug.
2.
Check that the mechanism is in the
unlocked position by turning the key
clockwise.
3.
Check that the indicator window is
showing red.
Starting and driving
4.
Insert and slide in the towball section
until it clicks.
NOTE! The trailer's safety cable must be
fastened to the attachment in the towing
bracket.
5.
Check that the indicator window is
showing green.
6.
Turn the key anti-clockwise to the locked
position. Remove the key from the lock.
115
Starting and driving
Removing the connector pin
1.
Insert the key and turn it clockwise to
the unlocked position.
4.
Slide in the cover plug.
116
2.
Press in the locking knob and turn it anticlockwise until it clicks.
3.
Continue turning the lock knob as far as
it will go. Hold it down at the same time
as pulling the towball section out.
Starting and driving
Loading
Loading the cargo compartment
Turn off the engine and apply the parking
brake when loading or unloading long
objects. The gear lever or gear selector can
be knocked out of position by long cargo,
causing the car to move off. Seats can be
folded down and head restraints removed to
extend the cargo compartment.
Position all cargo securely against the
backrest in front
•
Do not damage the head restraint when
folding the rear seat. The head restraints
can be removed as necessary.
•
Centre wide loads.
•
Heavy objects should be positioned as
low as possible. Avoid placing heavy
loads on the folded backrest.
•
Cover sharp edges with something soft.
•
Secure all cargo with normal or
restraining straps in the load securing
eyelets
•
Check periodically that the load carriers
and load are properly secured. Lash the
load securely with cargo straps.
•
The maximum roof load is 75 kg (165
lbs) (including load carriers).
•
Distribute the load evenly over the load
carriers. Do not load lopsidedly. Place
the heaviest items at the bottom.
•
The car’s centre of gravity and driving
characteristics change with a load on the
roof.
•
The wind resistance and fuel
consumption increases with the size of
the load.
•
Drive gently. Avoid quick accelerations,
heavy braking and hard cornering.
WARNING!
• Never load cargo above the backrests.
• The protection of the inflatable curtain
hidden in the headlining may be
compromised by high loads.
• Always secure the load. During heavy
braking the load may otherwise shift,
causing personal injury.
WARNING!
Bear in mind that if an object weighing
20 kg (44 lbs) is subjected to a head-on
collision at a speed of 50 km/h (30 mph),
its impact weight will be 1000 kg (2200
lbs).
Using load carriers
To avoid damage to the car and to ensure the
greatest possible safety while driving, it is
recommended that the load carriers
developed by Volvo for your car are used.
Follow the Installation Instructions supplied
with the load carriers.
117
Starting and driving
Adapting light pattern, right and left hand drive traffic
A. Light pattern for left hand drive traffic B.
Right hand drive traffic
Correct light pattern.
The light pattern of the headlamps can be
adjusted to prevent blinding the oncoming
traffic when driving with the wrong light
pattern. The correct light pattern gives
effective illumination of the edges of the road.
Halogen light
Bi-Xenon lamp
Headlamps with halogen lights
The control on the headlamp must be in
position (A) for left hand drive traffic and
position (B) for right hand drive traffic.
Headlamps with Bi-Xenon lights
The control on the headlamp must be in
position (A) for left hand drive traffic and
position (B) for right hand drive traffic.
WARNING!
If the car is equipped with Bi-xenon
headlamps, all work on the headlamps
must be carried out by a Volvo
workshop.
Bi-Xenon headlamps require great care
due to the high voltage element.
118
Wheels and tyres
Wheels and tyres
General information
Tyre pressure
Changing wheels
Spare Wheel and tools
Tyre Sealant System (certain markets)
120
123
124
127
128
119
Wheels and tyres
General information
Driving characteristics and tyres
New tyres
Tyres affect driving characteristics greatly.
Tyre type, size and tyre pressure are
important to how the car performs.
Tyres are perishable
goods. They will begin to
harden after a few years
and their friction
properties will be
reduced. When
changing tyres always
try to get as fresh tyres
as possible. This is
particularly important for
Winter tyres. The week
and year of manufacture is indicated by 4
digits, for example 1502. The tyre shown in
the illustration were manufactured week 15,
2002.
When replacing tyres, be sure to use the
same type, size and brand on all four wheels.
Otherwise the handling of the car could be
affected. Follow the recommended tyre
pressures stated on the decal on the fuel tank
filler cap.
List of dimensions
There is a size designation for all car tyres.
Example designation: 205/55R16 91 W.
205
Section width (mm)
55
Relationship between section height
and width (%)
R
Radial tyre
16
Wheel rim diameter in inches (")
91
Code digits for maximum permissible
tyre load (in this case 615 kg (1355
lbs)
W
The tyre is designed for speeds up to
240 or 270 km/h (150 or 170 mph).
120
Tyre age
Even if tyres have a theoretical service life of
up to ten years, it is recommended that tyres
older than six years are not used.
Tyres with tread wear indicators
Tread wear indicators are narrow, raised
areas located at right angles to the tread.
TWI is printed on the side of the tyre. When
a tyre is worn so that only 1.6 mm (0.06 inch)
of tread remains, the indicators will be clearly
visible. Replace with new tyres immediately.
Remember that tyres with little tread have
very poor grip in rain or snow.
Winter tyres
Volvo recommends winter tyres with a fixed
dimension. These are given on a decal on the
inside of the fuel filler flap. The tyre size is
dependent on the size of the engine. Always
use winter tyres on all four wheels.
Wheels and tyres
NOTE! Consult a Volvo dealership for advice
on the most suitable rims and tyre types.
Studded tyres
Studded winter tyres should be carefully
broken in over a distance of 500-1000 km
(300 – 600 miles) so that the studs become
properly positioned in the tyre. This gives the
tyre, especially the studs, a longer life.
IMPORTANT!
Only use Volvo Genuine snow chains or
similar that are adapted to the correct
model, tyre and wheel rim dimensions.
Consult your Volvo workshop. Never use
"quick links" because the space between
the disc brakes and the wheels is too
small.
NOTE! Regulations for the use of studded
tyres vary from country to country.
Tread depth
Roads with ice, snow and low temperatures
demand more from tyres than summer
driving. We therefore recommend a minimum
tread depth of 4 mm (0.15 inch)on winter
tyres.
Low and high wheel nuts
Rims and wheel nuts
Snow chains
Only rims which have been tested and
approved by Volvo and are Volvo Genuine
accessories may be used on the car. There
are two different types of wheel nut,
depending on whether the rims are steel or
aluminium.
Snow chains may only be used on the front
wheels.
Steel rims – low nut
NOTE! Never drive faster than 50 km/h (32
mph) with snow chains. Do not drive on
unfinished roads unnecessarily as this
causes heavy wear to both snow chains and
tyres. Never use "quick links" because the
space between the disc brakes and the
wheels is too small.
Steel rims are normally secured using the low
type of nut, although steel rims may also use
the high type. Tighten to 140 Nm. Check
torques using a torque wrench.
WARNING!
Never use the short type of nut for
aluminium rims. The wheel can become
loose.
121
Wheels and tyres
Aluminium rim – high nut
Only the high type of nut can be used for
aluminium rims. This is considerably different
from other types of nut because it has a
rotating conical thrust washer.
Tighten to 85 Nm. Check torques using a
torque wrench.
WARNING!
The higher wheel nuts must be tightened
to a maximum of 85 Nm. Harder
tightening can cause washer damage.
NOTE! This nut can also be used on steel
rims.
Lockable wheel nut
If steel rims with lockable wheel nuts are used
in combination with wheel covers, the
lockable wheel nut must be fitted to the stud
nearest the air valve. Otherwise the wheel
cover cannot be installed on the wheel.
Spare wheel Temporary Spare
The “Temporary Spare” 1 should only be
used for the short time it takes to repair or
replace the normal tyre. Switch back to a
normal wheel as soon as possible. The
1
Certain markets
122
handling of the car when using the
“Temporary spare” may be different.
Never drive above 80 km/h (50 mph) when
driving with a “Temporary spare wheel”.
IMPORTANT!
The car should never be driven with more
than one spare wheel fitted at the same
time.
Wheels and tyres
Tyre pressure
Checking the tyre pressure
Check tyre pressure regularly. The correct
tyre pressures are specified in the tyre
pressure table. The specified tyre pressures
relate to cold tyres (vary according to the
outside temperature). Driving on tyres with
incorrect tyre pressures impairs the car’s
handling and increases tyre wear. Tyres get
warm and pressure increases after just a few
kilometres driving. Therefore, do not let out
air if you check the pressure when the tyres
are warm. However, you should increase the
pressure if it is too low.
Recommended tyre pressure
The decal located on the inside of the fuel
filler flap indicates the correct tyre pressure.
Your car is fully approved, which means that
you may not deviate from those dimensions
and performance ratings indicated in the
vehicle registration. The only exceptions to
these regulations are winter and studded
tyres. If a winter or studded tyre is used the
car must not be driven faster than the tyre
classification, which is usually class Q with a
maximum permitted speed of 160 km/h (100
mph).
123
Wheels and tyres
Changing wheels
should always be at the rear (to reduce the
risk of skidding).
Wheels should be stored hanging up or on
their sides, never standing.
Contact a Volvo workshop if unsure about the
tread depth.
The arrow shows the direction of rotation of
the tyre
Summer and winter wheels
When shifting between summer and winter
wheels, mark the wheels to indicate where
they were fitted on the car, e.g. L = left, R =
right. Tyres with tread that are designed in
such a way that they should only roll in one
direction are marked with an arrow. Tyres
should have the same rotational direction
throughout their service life. Tyres should
only be switched between front and rear,
never between left and right and vice-versa.
Incorrectly fitted tyres impair the car’s braking
properties and ability to force aside rain,
snow and slush. The tyres with the most tread
124
Wheels and tyres
Removing wheels
Place at least one warning triangle if
changing a wheel on a public road. Ensure
that the car and jack are on a secure flat
surface.
1.
Take out the spare wheel, jack and
wheel brace. These are under the carpet
in the cargo compartment.
2.
Apply the handbrake. If the car is
manual, engage first gear. Select P if the
car is automatic.
3.
Place chocks on either side of the
wheels remaining on the ground. Use
large wooden blocks or large stones.
4.
Cars with steel rims have removable
wheel covers. Pry off the wheel cover
using the end of the wheel brace. It can
also be pulled off by hand. When
refitting the wheel cover, make sure the
cover is properly aligned over the air
valve.
5.
Slacken off the wheel nuts by ½-1 turns
anti-clockwise using the wheel brace.
6.
There are two jacking points on either
side of the car. Hold the jack against the
pin in the jacking point as shown and
wind down the jack foot so that it is
pressed flat against the ground. Check
that the jack sits securely in the
anchorage as shown and that the foot is
positioned vertically underneath the
anchorage.
7.
Lift the car so that the wheel is free.
Remove the wheel nuts and lift off the
wheel.
125
Wheels and tyres
Check torques using a torque wrench.
High wheel nuts with a rotating conical
thrust washer must be tightened to 85
Nm. Check torques using a torque
wrench.
WARNING!
• Never crawl under the car when it is
raised on a jack.
• Never leave passengers in the car
when jacking it up.
• Ensure that the car (and preferably a
barrier) is between passengers and
the road.
WARNING!
The higher wheel nuts must be tightened
to a maximum of 85 Nm. Harder
tightening can cause washer damage.
The car's original jack
Only use the car's original jack when
replacing a wheel. All other work on the car
must be carried out using workshop jacks
and axle stands under the part of the car that
is raised. The jack screw should be kept well
lubricated.
Fitting the wheel
1.
2.
3.
4.
126
Clean the mating surfaces on the wheel
and hub.
Fit the wheel. Screw the wheel nuts into
place.
Lower the car so that the wheels cannot
rotate.
Tighten the wheel nuts crosswise. It is
important that the wheel nuts are
correctly tightened. The low wheel nut
must be tightened to 140 Nm.
5.
6.
Install the wheel cover.
Screw the jack together completely
before returning it to the cargo
compartment. Ensure that the jack and
the wheel brace are properly secured.
Wheels and tyres
Spare wheel and tools
Spare wheel/Tyre Sealant
System, jack and wheel brace
The spare wheel or Tyre Sealant System with
a compressor, the jack and the wheelbrace
are placed under the floor in the cargo
compartment.
Taking out the Tyre Sealant System:
1. Pull up the floor mat, front and rear.
2. Lift up the Tyre Sealant System.
Taking out the spare wheel:
1. Pull up the floor mat, front and rear.
2. Lift out the jack and the wheelbrace.
3. Unscrew the spare wheel and lift it out.
127
Wheels and tyres
Tyre Sealant System (certain markets)
General
Cars not fitted with a spare wheel have been
supplied with a Tyre Sealant System instead.
The Tyre Sealant System comprises an
electric air compressor and a container of
sealing compound.
The Tyre Sealant System is only intended to
act as a temporary emergency repair,
allowing the car to be driven at most a further
200 km (120 miles) or to the nearest tyre
workshop. The sealing compound effectively
seals tyres that have been punctured by
objects with a diameter of up to 6 mm (0.23
inch). There is a risk that punctured tyres that
have sustained larger damage cannot be
sealed.
NOTE!
• Carefully read the instructions and the
warning information before using the
Tyre Sealant System.
• If other objects are to be inflated, a
nozzle specially intended for this
purposed must be used.
• Objects with a volume exceeding 50
litres (inflatable mattresses, inflatable
boats, etc.) should not be inflated using
the air compressor.
WARNING!
• The Tyre Sealant System is only
intended for sealing tyres with a
puncture in the contact surface.
• Do not use the Tyre Sealant System
to repair tyres that have been
punctured on the sidewall of the tyre
or tyres that display grooves, cracks,
unevenness or similar damage.
The Tyre Sealant System should only be used
in temperatures ranging from -40 °C to 70 °C.
The container of sealing compound must not
be used after the expiry date has passed. It
must be replaced before this.
Procedure
128
3.
1.
Ensure that the car is parked so that
other vehicles are not put at risk and the
traffic is not obstructed.
2.
Position the warning triangle to warn
other road-users.
Read the instructions and warning
information, if available. Otherwise
follow these instructions and the decals
on the air compressor and the container
of sealing compound.
4. Do not remove objects that remain in the
tyre after the tyre has been punctured.
5.
The compressor should not operate for
longer than 10 minutes. Allow the
compressor to cool when there is a risk
of overheating. Never drive above 80
km/h (50 mph) when the Tyre Sealant
System has been used for an
emergency repair.
Wheels and tyres
9.
Start the compressor by switching the
ON/OFF button (2) to position I. A
temporary increase in pressure of 4-6
bar will occur while the sealing
compound is being pumped. After
approximately 30 seconds the pressure
will drop and the pressure gauge will
display a more accurate tyre pressure
reading.
WARNING!
Sealing a punctured tyre
1.
Remove the label about the maximum
permitted speed (1) from the Tyre
Sealant System and attach it where the
driver can clearly see it.
2.
Ensure that the orange On/Off button is
in the 0 position.
3.
Take the cable and the hose from the
side compartment (3).
4.
Unscrew the valve cap on the punctured
tyre.
5.
Screw the hose (4) onto the tyre valve.
6.
Connect the connector (5) to the car's
12V electrical socket.
7.
Release the safety catch (6) and turn
the orange section (7) 90 degrees to
the vertical position.
8.
If the car is in a well-ventilated location,
the engine can be started to prevent the
battery from discharging.
WARNING!
Inhaling car exhaust fumes can be fatal.
Never leave the engine running in areas
that are enclosed or lack sufficient
ventilation.
Never stand next to the tyre while the
compressor is pumping. Pay particular
attention to the sidewalls of the tyres. In
the event of cracks, unevenness or similar
damage, the compressor should be
switched off immediately. In such
circumstances you should terminate your
journey . Contact an authorised tyre
workshop.
10. Fill the tyre to a minimum pressure of
1.8 bar. The pressure should not exceed
3.5 bar. Pump for approximately 7
minutes. Switch off the compressor to
check the actual pressure in the tyre. If
the pressure has not reached 1.8 bar
after pumping for 10 minutes, the
compressor should be disconnected.
129
Wheels and tyres
NOTE! The compressor should not operate
for longer than 10 minutes. Allow the
compressor to cool when there is a risk of
overheating.
11. Drive the car carefully approximately 10
metres forwards and backwards to
distribute the sealing compound in the
tyre. Repeat step 10.
WARNING!
If the pressure has still not reached 1.8
bar after 10 minutes, the tyre cannot be
sealed. Do not attempt to pump up the
tyre again. Contact an authorised tyre
workshop.
12. Disconnect the hose from the tyre valve
and refit the valve cap. Remove the
connector from the electric socket. Fold
back the orange section to its original
position and secure the catch. Store the
Tyre Sealant System in a safe place in
the car.
130
13. To ensure that the sealing compound
seals the tyre successfully, drive
approximately 3 kilometres (2 miles) as
soon as possible at a maximum speed of
80 km/h (50 mph).
WARNING!
Do not drive above 80 km/h (50 mph)
after the provisional puncture repair has
been used. The provisionally sealed tyre
must be replaced as soon as possible
(maximum recommended distance 200km
(120 miles)).
15. If the tyre pressure is higher than 1.3
bar, the tyre should be pumped to the
pressure specified in the tyre pressure
table on the fuel filler cap. If the tyre
pressure is too high, release air using
the relief valve (8).
16. Switch off the compressor. The On/Off
button should be in the 0 position.
Disconnect the hose from the tyre valve.
Reinstall the Tyre Sealant System under
the floor in the cargo compartment.
NOTE! The tyre pressure should be checked
again after an extended period of rest.
Pumping air only
14. Checking the tyre pressure again:
1. Connect the hose to the tyre valve.
2. Fit the connector in the electric
socket.
3. Read off the pressure on the
compressor's pressure gauge.
WARNING!
If the tyre pressure is below 1.3 bar, the
tyre has not been sealed sufficiently. In
such circumstances you should terminate
your journey. Contact an authorised tyre
workshop.
(only applies if there is a special nozzle)
NOTE! Objects with a volume exceeding 50
litres (inflatable mattresses, inflatable boats,
etc.) should not be inflated using the air
compressor.
1.
Ensure that the On/Off button is in the
0 position.
2.
Take the cable and the hose from the
side compartment (3).
Wheels and tyres
3.
Screw the special nozzle (may be
purchased from dealers) into place on
the hose (4). Connect the hose and
nozzle to the object that is to be inflated.
IMPORTANT!
The safety catch (6) should not be
released when the orange section is not
going to be used. The orange section
should be in the horizontal position.
4.
Connect the connector (5) to the car's
12V electrical socket.
5.
Start the engine. The car must be
standing in a well-ventilated area.
8. Switch off the compressor by setting the
On/Off switch to the 0 position when
the correct pressure has been achieved.
NOTE! The compressor should not operate
for longer than 10 minutes. Allow the
compressor to cool when there is a risk of
overheating.
WARNING!
Inhaling car exhaust fumes can be fatal.
Never leave the engine running in areas
that are enclosed or lack sufficient
ventilation.
6.
Start the compressor by switching the
ON/OFF button (2) to position I.
7.
Pump the object to the required
pressure. Do not inflate objects that
require a pressure higher than 4 bar.
131
Wheels and tyres
132
Car care
Car care
Cleaning
Touching up paintwork damage
Rustproofing
134
136
137
133
Car care
Cleaning
Washing the car
Wash the car as soon as it becomes dirty.
Use car shampoo. Road salt and moisture
can lead to corrosion.
•
Thoroughly rinse dirt off the underbody
of the car.
•
Rinse the entire car until the dirt has
softened. When using a high pressure
washer: Make sure that the nozzle of
the high pressure washer does not
come closer than 30 cm (12 inches)
from the bodywork. Do not spray
directly at the locks.
•
Wash using a sponge, car shampoo
and lukewarm water (maximum of
35 °C).
•
If the dirt is difficult to dislodge, wash
the car using a cold degreasing agent.
Do not expose the car to direct sunlight
as this can damage the paintwork. Be
sure that there is a drain separator
where you are washing the car
•
Dry the car using a clean, soft chamois.
•
Clean the wiper blades with a
lukewarm soap solution.
Removing bird droppings
Wash bird droppings off the paintwork as
soon as possible. Bird droppings contain
134
chemicals that affect and discolour paintwork
quickly. The discolouration cannot be
polished off.
WARNING!
Always have the engine cleaned by a
workshop. There is a fire risk if the engine
is hot.
Automatic car wash
Although an automatic car wash is a quick
and easy way to clean the car, it is no
substitute for a proper hand wash. The
brushes of an automatic car wash cannot
reach all points. We recommend that the car
is washed by hand for the first few months.
WARNING!
Always test the brakes after washing the
car to ensure that moisture and corrosion
do not affect the brake pads and impair
the brakes.
Gently press the brake pedal occasionally if
driving for long periods in rain or slush. This
heats and dries the brake pads. You should
also do this when you begin driving in
extremely damp or cold weather.
Cleaning the upholstery
Treating marks on fabric
A special cleaning agent available at your
Volvo dealer is recommended when cleaning
fabric upholstery. Other chemicals can impair
the fire retardant qualities of the upholstery.
IMPORTANT!
Sharp objects and Velcro may damage
the textile upholstery.
Treating marks on vinyl
Wash the vinyl with a weak soap solution and
lukewarm water. Never scrape or rub a mark.
Never use strong stain removers.
Treating marks on leather
A special cleaning agent available at your
Volvo dealer is recommended when cleaning
leather upholstery. Treat the leather
upholstery once or twice a year using Volvo's
leather care kit. Never use strong stain
removers. Such products may damage fabric,
vinyl and leather upholstery.
Car care
Cleaning seat belts
Use water and synthetic detergent.
Polishing and waxing
Polish and wax the car when the paintwork is
dull or when you wish to give the paintwork
extra protection.
The car does not need to be polished until it
is at least one year old. However the car can
be waxed during this time. Do not polish or
wax surfaces warmer than 45° C.
•
Wash and dry the car thoroughly before
you begin polishing or waxing. Clean
off asphalt and tar stains using white
spirit. More stubborn marks can be
removed using fine rubbing paste
designed for paintwork.
•
Polish first with a polish and then wax
with liquid or solid wax. Carefully follow
the instructions on the packaging.
Many preparations contain both polish
and wax.
135
Car care
Touching up paintwork damage
If the stone chip has penetrated to the
panel
1. Apply a piece of masking tape over the
damaged surface. Then remove the tape,
removing any paint residue.
2. Stir the primer thoroughly and apply
using a fine brush or matchstick. Apply
paint using a brush once the primer is
dry.
3. For scratches, proceed as above, but
mask around the damaged area to
protect the undamaged paintwork.
Paint
Stone chips and scratches
Paint is an important part of the car’s
rustproofing and should therefore be
checked regularly. To avoid the onset of rust,
damaged paintwork must be rectified
immediately. The most common types of
damage to paintwork are stone chips,
scratches and marks on the wing edges and
doors for example.
Before touching up paintwork, the car must
be clean and dry and at a temperature above
15°C.
•
Brush
Colour code
It is important that the correct colour is used.
The code for the car’s paint is on the product
plate on the B-post. See page 192.
•
Masking tape.
136
Material
• Primer in a can
•
Paint in a can or a touch-up pen
Minor stone chips and scratches
If the stone chip has not penetrated to the
bare metal and an undamaged colour coat
remains, you can add paint immediately after
removing dirt.
4. After a few days, polish the touched-up
areas. Use a soft rag and apply lapping
paste sparingly.
Car care
Rustproofing
Checks and maintenance
Your car received a thorough and complete
rustproofing at the factory. Parts of the body
are made of galvanised sheet metal. The
underbody is protected by a wear-resistant
anti-corrosion compound. A thin, penetrative
rustproofing liquid was sprayed into the
members, cavities and closed sections.
Maintaining the car's rustproofing.
•
Keep the car clean. Hose down the
underbody. When using a pressure
washer, keep the nozzle at least 30 cm
(12 inches) from painted surfaces.
•
Regularly check and touch-up the
rustproofing treatment as necessary.
The car’s rustproofing does not normally
require treatment for approximately eight
years. After that time, it should be treated at
three yearly intervals. If the car needs further
treatment, please contact a Volvo workshop.
137
Car care
138
Maintenance and service
Maintenance and service
Volvo Service
Maintaining your car yourself
Bonnet and engine compartment
Diesel
Oils and fluids
Wiper blades
Battery
Bulb types
Replacing front bulbs
Replacing rear bulbs
Replacing inner bulbs
Fuses
140
141
142
144
145
148
149
151
152
155
156
158
139
Maintenance and service
Volvo Service
Volvo service programme
Installing accessories
Before the car left the factory, it was
thoroughly test driven. It was checked again
in accordance with Volvo Car Corporation
regulations before it was handed over to you.
To keep your Volvo as safe and reliable as
possible, follow the Volvo service programme
specified in the Service and Warranty
Booklet. Have a Volvo workshop carry out
service and maintenance work. Volvo
workshops have the personnel, special tools
and service literature that guarantee the
highest quality of service.
Incorrect connection and installation of
accessories can negatively affect the car’s
electrical system. Certain accessories only
function when the appropriate software has
been programmed into the car’s electrical
system. Always contact your Volvo workshop
before installing accessories which are
connected to or affect the electrical system.
IMPORTANT!
For the Volvo warranty to apply, check and
follow the instructions in the Service and
Warranty Booklets.
Special service measures
Certain service measures, which affect the
car’s electrical system, can only be carried
out using electronic equipment specially
developed for your car. Always contact your
Volvo workshop before beginning or carrying
out service work which affects the electrical
system.
140
Recording vehicle data
One or more of the computers in your Volvo
are capable of recording detailed information.
This information is intended for use in
research in order to further develop safety
and for diagnosing faults in some of the car's
systems and may include details regarding;
frequency of seat belt use by the driver and
passenger, information on various vehicle
system/module functions and information
regarding engine, throttle, steering, brakes
and other system status. This information can
include details concerning the way the driver
drives the car. This type of information can
include, without being limited to, specific
details such as the car's speed, the use of the
brake and accelerator pedals and steering
wheel position. The latter data can be stored
for a limited period while the car is being
driven and subsequently during a collision or
a near-collision. Volvo Car Corporation will
not distribute the stored information without
consent. However, Volvo Car Corporation
may be forced to distribute the information
due to national legislation. Volvo Car
Corporation and its workshops may also read
and utilise the information.
Adverse driving conditions
Change engine oil and replace air and oil
filters more often than recommended in the
Service and Warranty manual when driving in
adverse conditions.
Adverse driving conditions include regular
use:
•
in dusty or sandy environments
•
when towing caravans or trailers
•
in mountainous regions
•
at high speed
•
at idle or at low speed
•
short journeys (less than 10 km (6 miles)
at low temperatures (below 5ºC ).
Maintenance and service
Maintaining your car yourself
Before starting work on the car
The battery
•
Check that the battery cables are
correctly connected and tightened.
•
Never disconnect the battery when the
engine is running (e.g. when replacing
the battery).
•
Never use a fast charger to charge the
battery. The battery cables should be
disconnected while charging.
•
The battery contains acid that is both
corrosive and poisonous. It is important
that the battery is handled in an
environmentally friendly way. Let your
Volvo dealer assist you.
WARNING!
• The ignition system has very high
voltage. The voltage in the ignition
system is dangerous. The ignition
must therefore always be switched
off when working in the engine
compartment.
• Do not touch the spark plugs or
ignition coils when the ignition is on
or the engine is hot.
141
Maintenance and service
Bonnet and engine compartment
Opening the bonnet
Open the bonnet:
•
Pull the handle on the far left under the
dashboard. You will hear when the catch
releases.
•
Insert your hand in the centre of the
front edge of the bonnet and press up
the safety catch handle.
•
Open the bonnet.
WARNING!
Check that the bonnet catches engage
properly when closed.
142
Engine compartment
1. Washer fluid reservoir, 4 l (4 cyl.)
2. Expansion tank for cooling system
3. Power steering fluid reservoir
4. Dipstick for engine oil1
5. Radiator
6. Radiator fan
7. Washer fluid reservoir, 6.5 l (5 cyl.)
8. Clutch and brake fluid reservoir (righthand drive)
9. Topping up, engine oil1
10. Clutch and brake fluid reservoir (lefthand drive)
1
Tyre pressure may vary depending on the
ambient temperature.
11. Battery
12. Relay and fuse box
13. Air filter*
Maintenance and service
Check regularly
Check the following at regular intervals, for
example, when filling up:
•
Coolant - The level must be between the
MIN and MAX marks on the expansion
tank.
•
Engine oil - The level should be between
the MIN and MAX marks.
•
Power steering fluid - The level should
be between the MIN and MAX marks.
•
Washer fluid - The reservoir must be
well filled. Top up with anti-freeze at
temperatures around freezing.
•
Brake and clutch fluid - The level must
be between the MIN and MAX marks.
WARNING!
• Remember that the radiator fan may
start automatically after the engine
has been switched off.
• Always have the engine cleaned by a
workshop. There is a fire risk if the
engine is hot.
143
Maintenance and service
Diesel
Fuel system
Diesel engines are sensitive to contaminants.
Only use diesel from a well-known oil
company. Never fill up with diesel if the
quality is dubious. The large oil companies
also produce a special diesel for use when
the outside temperature is around freezing.
This fuel is less viscous at low temperatures
and reduces the risk of wax building up in the
fuel system.
The risk of condensation building up in the
tank is reduced if the tank is kept well filled.
When refuelling, check that the area around
the fuel filler pipe is clean. Avoid spilling onto
the paintwork. Wash off any spillage with
detergent and water.
Empty tank
No special procedures are required if the
tank runs dry.
RME (Rape Methyl Ester)
A maximum of 5% RME may be mixed with
the diesel.
IMPORTANT!
There is a danger of engine damage if the
RME concentration is greater than 5%.
144
Draining condensation from the
fuel filter
Condensation is separated from the fuel in
the fuel filter. Condensation can disrupt the
engine.
The fuel filter must be drained at the intervals
specified in the Service and Warranty Book
or if it is suspected that the car has been filled
with contaminated fuel.
Maintenance and service
Oils and fluids
Dipstick, petrol engines
Dipstick, diesel engines
Changing the oil and oil filter
Volvo recommends that the oil level is
checked every 2500 km (1550 miles). The
most accurate measurement is made on a
cold engine before starting. An incorrect
measurement may be taken immediately after
the engine is switched off. The dipstick
indicates that the level is too low because the
oil has not had time to flow down into the oil
sump.
There are instructions in the Service and
Warranty Manual indicating the replacement
intervals for oil and oil filters. Shorter intervals
are recommended if driving in adverse
conditions. See page 140.
Check the oil level
The engine oil level must be checked and the
oil must be changed regularly. It is important
to check the oil level before the first regular oil
change is due on the new car. The serviceand warranty book specify measurements.
Checking the oil in cold cars:
•
Wipe the dipstick clean before the
check.
•
Check the oil level using the dipstick.
The oil level should be between the MIN
and MAX marks. If the level is close to
The oil level must be within the marked area
on the dipstick.
the MIN mark, top up using 1.0 litre of oil.
Top up until the oil level is nearer the
MAX mark than the MIN mark.
Checking the oil in warm cars:
•
Park the car on a level surface and wait
at least 10 to 15 minutes after switching
off the engine so that the oil has time to
run back to the oil sump.
•
Wipe the dipstick before checking.
•
Check the oil level using the dipstick.
The oil level should be between the MIN
and MAX marks.
145
Maintenance and service
•
Top up with engine oil if necessary. If the
level is close to the MIN mark, top up
using 1.0 litre of oil. Run the car to
operating temperature and switch off
the engine. Wait 10-15 minutes and
check the level again. Top up until the oil
level is nearer the MAX mark than the
MIN mark.
IMPORTANT!
Never fill above the MAX mark. Oil
consumption may increase if too much oil
is poured into the engine.
Topping up washer fluid, depending on
engine type
WARNING!
Do not spill oil on the hot exhaust
manifold as this is a fire risk.
Washer fluid reservoir
The windscreen and headlamp washers
share a common fluid reservoir.
1. Filling 4 cylinder models and diesel. The
reservoir holds approx. 4 litres.
2. Filling 5 cylinder models. The reservoir
holds approx. 6.5 litres.
Add anti-freeze protection in the winter so
that the fluid does not freeze in the pump,
reservoir and hoses.
IMPORTANT!
Mix the anti-freeze with water before
filling.
146
Coolant reservoir
Coolant
Use a mixture of half water, half coolant.
Follow the instructions on the packaging. It is
important to use equal amounts. Never top
up with ordinary water only. The risk of
freezing increases with both too little and too
much coolant.
IMPORTANT!
Some engine components are
manufactured in aluminium alloy.
Therefore it is extremely important always
to use coolant with anti-corrosion agent
as recommended by Volvo. When the car
is new, it is filled with coolant that can
withstand approximately –35°C.
Maintenance and service
Check the coolant regularly
The level must be between the MIN and MAX
marks on the expansion tank. If the system is
not filled sufficiently, high local temperatures
could occur, causing a risk of damage
(cracks) to the cylinder head. Top up the
coolant when the level falls to the MIN mark.
NOTE! The engine must only be run with a
well-filled cooling system. High temperatures
can occur, causing a risk of damage (cracks)
to the cylinder head.
WARNING!
The coolant may be extremely hot. If
topping up is required when the engine
is at operating temperature, slowly
unscrew the expansion tank cap to
disperse overpressure.
Clutch and brake fluid reservoir
Power steering fluid reservoir
The brake and clutch fluid have a common
reservoir. The location of the reservoir differs
between right and left-hand drive cars. The
level must be between the MIN and MAX
marks.
Recommended brake fluid: DOT 4+. Check
the level regularly. Change the fluid every
other year or at every other regular service
interval.
The level must be between the MIN and MAX
marks.
Grade: Volvo Power steering fluid. Check
the level at every service. It is not necessary
to change the fluid.
IMPORTANT!
The fluid should be changed annually on
cars used in conditions requiring hard,
frequent braking, such as driving in
mountains or tropical climates with high
humidity.
NOTE! If a fault should arise in the power
steering system or if the car is without power
and must be towed, it can still be steered.
However the steering will be much heavier
than normal and more power will be required
to turn the wheel.
147
Maintenance and service
Wiper blades
Replacing wiper blades
1.
Fold out the wiper arm and fold out the
wiper blade at 90° to the wiper arm.
2. Pull the wiper blade off the shaft,
straight to the side.
3. Slide in the new wiper blade, at 90º to
the wiper arm.
4. Fold in the wiper blade under the metal
plate and fold the wiper arm down.
NOTE! The wiper blades are different
lengths. The blade on the driver's side is
longer than the blade on the passenger side.
148
Maintenance and service
Battery
NOTE! Never fill above the maximum mark
(A).
Store the battery out of
the reach of children.
IMPORTANT!
Always use distilled or deionised water
(battery water).
•
Tighten the cover properly.
NOTE! The service life of the battery may be
negatively affected if it is repeatedly
discharged.
Symbols on the battery
Battery care
The service life and function of the battery
can be affected by numerous starts,
discharges, driving styles, conditions and
climate conditions etc.
The battery contains
corrosive acid.
Avoid sparks and open
flames.
The symbols are on the battery.
Use protective goggles.
Risk of explosion.
For the battery to function satisfactorily,
consider the following:
•
Regularly check that the battery fluid
level is correct (A).
•
Check all cells. Use a screwdriver to
remove the cover. Each cell has its own
maximum level mark.
•
If necessary, top up to the battery's
maximum mark using distilled water.
Further information can
be found in the owner’s
manual.
149
Maintenance and service
Replacing the battery
1.
Switch off the ignition and remove the
key.
2. Unscrew the cover over the battery.
3. Wait at least 5 minutes before touching
any electrical terminals (so that the
information in the car’s electrical system
can be stored in the different control
modules).
4. Remove the cover and unscrew the
front wall of the battery box using a
screwdriver.
5. Disconnect the battery negative lead.
6. Release the clamp holding the battery.
7. Disconnect the positive lead.
Install the battery in the reverse order.
WARNING!
Batteries can generate oxyhydrogen,
which is highly explosive. A spark, which
can be generated if the jump leads are
incorrectly connected, is sufficient to
explode the battery. The battery also
contains sulphuric acid, which can
cause serious corrosive damage. If the
acid comes into contact with your eyes,
skin or clothes, flush with large
quantities of water. If acid splashes into
your eyes, contact a doctor immediately.
150
Maintenance and service
Lamp types
7.
Courtesy lighting,
Cargo compartment
lighting
W5W
8.
Vanity mirror
1.2W
9.
Number plate lighting,
Parking lamps in
headlamps Direction
indicator lamps
(yellow)
W5W
10.
Fog lamps
55W H11
Environment
Bulbs in the car
1.
Dipped beam
55W
H7LL
2.
Bi-Xenon (option) gas
discharge lamps
35W D2S
3.
Main beam
55W HB3
4.
Brake lamp, Fog
lamp, rear
P21W
5.
Direction indicator,
rear + front (yellow)
PY21W
6.
Tail lamps, Position/
parking lamps, Side
marker lamps
W5WLL
Bi-Xenon lamps contain a small amount of
mercury. Burnt out bulbs must be handled
correctly. Contact a Volvo workshop for
advice.
IMPORTANT!
Never touch the glass of bulbs with your
fingers. Grease and oils from your
fingers are vaporised by the heat. This
coats and damages the reflector.
NOTE! Lamps and spotlights that are not
presented here should be replaced by a
Volvo workshop.
151
Maintenance and service
Replacing front bulbs
1.
Removing the bulb holder
All front bulbs (except for fog lamps) are
replaced by disconnecting and removing the
lamp housing via the engine compartment.
Remove the ignition key and turn the
light switch to position 0
2. Pull up the lamp housing's locking pin
(1)
3. Pull the lamp housing to one side and
then forwards (2)
4. Disconnect the connector
5. Lift out the lamp housing and place it on
a soft surface so as not to damage the
lens.
Installing the lamp housing:
1. Install the lamp housing in reverse order.
Check that the lock pin is correctly
situated.
2. Check the lighting.
NOTE! The lamp housing must be connected
and securely positioned before turning on the
lights or before inserting the ignition key in
the ignition.
Cover with lock catches
Dipped beam
1.
2.
3.
WARNING!
If the car is equipped with Bi-Xenon
headlamps, all work on the headlamps
must be carried out by a Volvo
workshop.
Bi-Xenon headlamps require great care
due to the high voltage element.
152
4.
5.
Remove the entire lamp housing.
Move the lock catches to one side and
remove the cover.
Release the spring clamp holding the
bulb. First push to the right so that the
spring clamp releases, then out and
down.
Pull out the bulb.
Remove the connector from the bulb.
Maintenance and service
Dipped beam
Fitting the bulb
1. Install the new bulb. It can only be fitted
in one position.
2. Press the spring clamp up and a little to
the left so that it snaps into place.
3. Press the connector back into position.
4. Reinstall the plastic cover.
5. Reinstall the lamp housing.
Main beam
Position/parking lamps
1.
2.
1.
3.
Remove the entire lamp housing.
Twist the bulb holder anticlockwise, pull
it out and replace the bulb. (Note how
the bulb holder is positioned.)
Reinstall the bulb holder. It can only be
installed one way
2.
3.
Pull the bulb holder out using pliers. Do
not pull out the bulb holder by pulling
the electrical cable.
Replace the bulb.
Press the bulb holder back into position.
It can only be installed one way.
153
Maintenance and service
Direction indicator
Side marker lamps
Fog lamps
1.
1.
1.
2.
3.
Twist the bulb holder anti-clockwise and
remove it.
Press the bulb inwards, turn it
anticlockwise and remove it from the
bulb holder.
Replace with a new bulb and reinstall
the bulb holder in the lamp housing.
2.
Twist the bulb anticlockwise, pull it out
and replace the bulb.
Reinstall the bulb holder. It can only be
fitted in one position.
2.
3.
4.
5.
6.
7.
8.
154
Switch off all lights and turn the ignition
key to position 0.
Remove the panel around the lamp
housing.
Unscrew both the torx screws in the
lamp housing and take out the lamp
housing.
Remove the connector from the bulb.
Turn the bulb anticlockwise and pull it
out.
Locate the new bulb in its seat and turn
clockwise.
Connect the connector to the bulb.
Secure the lamp housing using the
screws and press the panel back.
Maintenance and service
Replacing rear bulbs
Removing the bulb holder
All bulbs in the rear lamp cluster can be
replaced from inside the cargo compartment
1.
Switch off all lights and turn the ignition
key to position 0.
2. Remove the hatches in the left/right
panels to access the bulbs.
These bulbs are placed in a common bulb
holder.
1.
2.
3.
4.
Disconnect the connector from the bulb
holder.
Press the catches together and pull out
the holder.
Replace the bulb.
Press the connector back into position.
5.
Press the bulb holder into place.
Reinstall the cover.
Location of bulbs in the rear
lamp cluster
1.
Brake light
2.
Position/parking lamps
3.
Direction indicator
4.
Rear fog lamp (one side)
5.
Reversing lamp
P21W LL
BA15s
P5W LL
BAY15d
PY21W
LL
P21W LL
BA15s
P21W LL
BA15s
High-level brake light
These bulbs are of a special type. It is
recommended that these are replaced by a
Volvo workshop.
Number plate lighting
Replacing bulb
1. Switch off all lights and turn the ignition
key to position 0.
2. Remove the screw using a screwdriver.
3. Carefully detach the entire lamp housing
and pull it out. Turn the connector
anticlockwise and pull out the bulb.
4. Replace the bulb.
5. Refit the contact and turn clockwise.
6. Refit the entire lamp housing and screw
it into place.
155
Maintenance and service
Replacing inner bulbs
Courtesy lighting
Cargo compartment
Vanity mirror lighting
There is courtesy lighting under the
dashboard on the driver and passenger
sides.
1.
Removing mirror glass:
1. Insert a screwdriver underneath the
lower edge, in the centre. Carefully pry
up the lug on the edge.
2. Insert the screwdriver underneath the
edge on the left and right-hand side (by
the black rubber sections). Carefully pry
up so that the lower edge of the glass
releases.
3. Carefully detach and lift out the entire
mirror glass and cover
4. Remove the blown bulb and replace it
with a new one.
1.
2.
3.
4.
156
Insert a screwdriver and gently turn so
that the lens detaches.
Remove the faulty bulb.
Install the new bulb.
Reinstall the lens.
2.
3.
4.
Insert a screwdriver and gently turn so
that the lamp housing loosens.
Remove the faulty bulb.
Install the new bulb.
Reinstall the lamp housing.
Maintenance and service
Installing the mirror glass:
1. First press the three lugs at top edge of
mirror glass back into position.
2. Then press the three lower lugs back
into position.
157
Maintenance and service
Fuses
All electrical functions and components are
protected by number of fuses to protect the
car’s electrical system from damage by shortcircuits or overloads.
The fuses are in two different locations in the
car:
•
Relay/fuse box in the engine
compartment.
•
Relay/fuse box in the passenger
compartment.
Replacement
If an electrical component or function does
not work, it may be because the component’s
fuse was temporarily overloaded and blew.
1.
Look in the fuse diagram to locate the
fuse.
2. Pull out the fuse and look at it from the
side to see if the curved wire is burned
out.
3. If this is the case, replace it with a new
fuse of the same colour and amperage.
If the same fuse burns out repeatedly it
means that there is a fault in the component.
Please contact a Volvo workshop to carry out
a check.
Relay/fuse box in the engine
compartment
The fuse box contains 36 fuse positions. Be
sure to replace a blown fuse with a new fuse
of the same colour and amperage.
•
1-6 are the “Midi Fuse” type and may
only be replaced by a Volvo workshop.
•
7-18 are the “JCASE” type and should
be replaced by a Volvo workshop.
•
19 - 36 are the “Midi Fuse” type.
On the inside of the cover there are spare
fuses and pliers to assist in removing and
replacing fuses.
158
Maintenance and service
Fuse positions in the relay/fuse
box in the engine compartment
1.
2.
3.
Radiator fan, 50A
Power steering, 80A
Supply to the fuse box in the passenger
compartment, 60A
4. Supply to the fuse box in the passenger
compartment, 60A
5. Element climate control unit, 80 A
6. Glow plugs (diesel), 60 A
7. ABS pump, 30 A
8. ABS valves, 20 A
9. Engine control module, 30A
10. Fan climate control unit, 40 A
11. Headlamp washers, 20 A
12. Heated rear window , 30A
13. Starter motor relay, 30A
14. Electrical socket for trailers, parking
assistance, accessory module, 40 A
15. Spare position
16. Supply to the fuse box in the passenger
compartment, 30A
17. Windscreen wipers, 30A
18. Supply to the fuse box in the passenger
compartment, 40A
19. Spare position
20. Horn, 15A
21. Additional heater, passenger
compartment heater (fuel powered),
20A
22. Spare position
23. Engine control module (ECM) /
transmission control module (TCM),
10A
24. Heater diesel filter, 20 A
25. Spare position
26. Ignition switch, 15A
27. Air conditioning (A/C) compressor, 10A
28. Spare position
29. Fog lamps front, 15A
30. Engine control module, 3A
31. Voltage regulator, generator, 10 A
32. Injectors (5 cyl.), 10 A
33. Heater element heated oxygen sensor
(HO2S) (5 cyl), air preheating valve
(diesel), 20A
34. Ignition coils, fuel pump (diesel), 10A
35. Engine sensor valves, relay air
conditioning, 15 A
36. Engine control module (ECM), 10A
159
Maintenance and service
Relay/fuse box in the passenger
compartment
2.
The fuse box contains 56 fuse positions. The
fuses are located under the glove
compartment.
3.
There are spare fuses and pliers in the in the
integrated relay/fusebox in the engine
compartment to assist in removing and
replacing fuses.
Replacing fuses:
1.
160
Remove the interior upholstery covering
the fuse box by first pressing in the
centre pins in the mounting clips (1)
approximately 1 cm (0.4 inch ) and then
pulling these out
4.
5.
Turn both the butterfly screws (holding
the fuse box in position) (2) anticlockwise until they release
Fold down the fuse box (3) half way. Pull
towards the seat until it stops. Fold
down completely. The fusebox can be
unhooked completely.
Close the fusebox in reverse order.
Pull the centre pins fully out of the
mounting clips, secure the upholstery
with the mounting clips and press the
loose pins into the mounting clips again.
The mounting clips then expand, holding
the upholstery in position.
Maintenance and service
Fuse positions in the relay/fuse
box in the passenger
compartment
37
38.
39.
40.
41.
42.
43.
44.
45.
46.
Spare position
Spare position
Spare position
Spare position
Spare position
Spare position
Telephone, audio, 15 A
SRS system, 10 A
Electric socket, rear seat, 15 A
Lighting in passenger compartment,
glove compartment and entry, 5 A
47. Lighting in the roof, door mirrors, 5 A
48. Windscreen washer, wiper rear window,
15 A
49. SRS system, 10 A
50. Spare position
51. Additional heater (Positive temperature
coefficient (PTC)) lighting front, 10 A
52. ABS-system, 5 A
53. Power steering, 10 A
54. Transmission control module (TCM),
differential gear, 10 A
55. Remote control receiver, 20 A
56. Battery charging, 10 A
57. Computer system, brake light contact,
15 A
58. Main beam right, auxiliary lamp, 7.5 A
59. Main beam left, auxiliary lamp, 7.5 A
60. Seat heater driver's side, 15 A
61. Seat heater passenger side, 15 A
62. Sunroof, 20 A
63. Power window rear, right-hand side, 20
A
64. Audio, 5 A
65. Infotainment, 5 A
66. Climate control module (CCM)/
infotainment control module (ICM), 10 A
67. Sub-bass, 15 A
68. Cruise control, 5 A
69. Climate control, rain sensor, 5 A
70. Spare position
71. Spare position
72. Spare position
73. Sun roof, console for interior lighting
(OHC), seat belt reminder rear, 5 A
74. Relay fuel pump, 15 A
75. Spare position
76. Spare position
77. Electric socket, cargo compartment, 15
A
78. Spare position
79. Reversing lamps, 5 A
80. Spare position
81. Power window rear, left-hand side, 20 A
82. Power window front, passenger side, 25
A
83. Power window front, driver's side, 25 A
84. Power passenger seat, 25 A
85. Power driver's seat, 25 A
86. Interior lighting relay, power seats, 5 A
161
Maintenance and service
162
Infotainment
Infotainment
Infotainment
Control panel
Audio functions
Radio functions
CD/MD (option)
CD changer (option)
Menu settings and selections - Audio
Telephone functions (option)
Telephone functions
Menu settings and selections - Telephone
164
165
167
169
175
176
178
180
182
188
163
Infotainment
Infotainment
Audio and telephone system
(option)
Infotainment is a system with integrated
audio and telephone functions. The
infotainment system can be used easily and
conveniently using the common control panel
or the steering wheel keypad. The control
panel display indicates the present function.
The system can be equipped with Dolby
Surround Pro Logic II (option). It gives more
natural sound reproduction.
There are three levels of audio system:
• Performance:
AM/FM radio, CD player, 4x25W, four
broad range loudspeakers (or four
broad range speakers and two treble
speakers in certain markets).
•
High Performance:
AM/FM radio, CD player, 4x40W, eight
loudspeakers (bass and treble speakers
in each door).
•
Premium Sound:
AM/FM radio, CD changer (six discs),
4x70W + 25W, Dolby Pro Logic II, 12
speaker (bass, mid range and treble in
the front doors, bass and treble in the
rear doors, bass and treble in the
dashboard centre loudspeaker).
164
The exact specifications for these levels may
vary between markets. Certain levels are not
offered in all markets. The option list (subbass, CD/MD player, CD changers,
telephone, navigation etc.) differs between
the different markets. Not all options are
available for all levels.
Infotainment
Control panel
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
POWER – Audio On/Off
PHONE – Telephone on/off/
standby
VOLUME – Controls the volume
CD/MD – Changes between CD or
MD
AM/FM – Shortcut button to switch
between FM1, FM2 and AM
MENU – Opens the main menu
ENTER – Select in the menu,
activate a selection or activate the
telephone from standby mode
EXIT – Scroll back in the menu,
cancel a selection, put the
telephone in standby mode, or
erase the previous character when
entering text and numbers.
Navigation button – scroll up or
down in the menus, scan/change
tracks, stations or scroll forwards or
back when entering text and digits
TUNING – Scan/change tracks,
station
SOUND – Sound settings
SCAN – Automatic station search
AUTO – Find and store the
strongest stations
Display – Presents options, menus
and information
15.
16.
17.
Opening for insert/eject
Eject – CD/MD
Station setting buttons/selecting
CD changer position (1-6), number/
character buttons for the telephone
and menu shortcuts
Control panel centre console
165
Infotainment
Display
The display will show the function in use, for
example menu selections, messages,
telephone numbers or settings. In daylight
the information is displayed against a light
background. In darkness it is displayed
against a dark background. Clean the display
with a soft, dry cloth. Never use cleaning
agent.
This display is also used for the climate
control.
Using the menu
Steering wheel keypad
Steering wheel keypad (option)
The four buttons at the bottom of the steering
wheel keypad control both the radio and the
telephone. The function of the button
depends on which system is active. The
steering wheel keypad can be used to adjust
volume, shift between preset stations and
change CD/MD tracks.
The telephone must be activated in order to
control the telephone functions using the
arrow keys. The telephone must be in
standby mode to make audio system settings
using these buttons. Hold the one of arrow
keys depressed to fast forward/rewind or
search for the next station.
166
Press MENU to access the main menu. The
settings for audio system source (radio for
example) are selected from the main menu.
Audio settings cannot be made if the audio
system is not switched on.
Using the menu:
• The navigation button scrolls up and
down in the menu.
•
A brief press on EXIT allows you to
clear, cancel or decline an alternative or
to go back one step in the menu
structure.
•
Press ENTER to confirm, select or scroll
from a submenu to the next submenu.
Infotainment
Audio functions
Volume control
Turn the volume knob clockwise or
anticlockwise to increase or lower the
volume. Volume control is infinitely variable.
The volume can also be increased or lowered
using the steering wheel keypad.
Pause mode
When the volume at zero, the CD/MD player
switches to pause mode. Reactivate the
player by turning up the volume.
Audio On/Off
Press the POWER button to switch the audio
system on or off. If the audio system is active
when the ignition is switched off, it will
reactivate automatically when the car is
restarted.
Selecting the sound source
Use the CD/MD and AM/FM quick selection
buttons when selecting the sound source.
•
Press the AM/FM button repeatedly to
shift between FM1, FM2 and AM.
The selected sound source is shown in the
display.
Volume control for TP, PTY,
news and alarm
If a CD is playing when the radio receives a
traffic bulletin, the CD player enters pause
mode. The message is played at the volume
selected for that type of message. It then
returns to the CD player function. If the
volume is adjusted while the bulletin is
played, the new volume is saved and used for
the next bulletin.
Sound setting
•
Press SOUND
•
Press the SOUND button repeatedly
until you reach the function you wish to
set. Select between SUB-BASS
(option), TREBLE, FADER, BALANCE,
CENTER (option) or SURROUND
(option).
•
Use the TUNING knob to set the sound.
The display shows a scale from min. to
max. position. The middle indicates the
normal position.
Sound setting
Bass
Treble
Balance between the
right and left-hand
speakers
Balance between the
front and rear speakers
Level for bass speaker
(option)
Level for centre
speaker (option)
Level for surround
sound (option)
Shown in the
display
BASS
TREBLE
FADER
BALANCE
SUB-BASS
CENTRE
SURROUND
The level of the centre speaker can only be
set if Dolby Pro Logic II (DPL II) or threechannel stereo (3CH) has been selected
from the menu.
The level for Sub bass can only be set if the
sub bass is activated.
Dolby Pro Logic II (option)
Dolby Surround Pro Logic II with centre
dashboard speaker in the middle of the
167
Infotainment
dashboard provides a more realistic audio
experience.
Bass speaker- Sub-bass
4. Select Equalizer Front and press
ENTER.
5. Use the navigation button or TUNING
knob to set the level.
6. Use the navigation button to select the
next frequency. Five frequencies can be
adjusted.
7. Press ENTER to save any changes and
exit.
8. Press EXIT to exit without saving any
changes made.
(accessory)
Equalizer, rear
Gives a fuller sound and deeper bass to the
system:
(certain models)
Dolby Surround Pro Logic II
and the Dolby icon are
trademarks of Dolby
Laboratories Licensing
Corporation. Dolby Pro Logic
II Surround System is
manufactured under license
from Dolby Laboratories
Licensing Corporation.
The normal left and right stereo channels are
divided into left-centre-right. In addition,
ambient surround sound is produced by the
rear loudspeaker channels .
Dolby Surround Pro Logic II functions in CD
and MD modes. 3-Channel stereo is
recommended for AM and FM radio
broadcasts. Dolby Surround Pro Logic II is
only available for the highest audio level,
Premium Sound.
Setting the surround sound:
1. Press MENU.
2. Select the menu for the present sound
source and press ENTER.
3. Select Sound settings in the menu and
press ENTER.
4. Select Surround AM/FM or Surround
CD/MD and press ENTER.
5. Select Pro Logic II, 3 channel stereo or
Off and press ENTER.
The symbol Dolby PL II is shown in the
display if Pro Logic II has been selected.
3 CH is shown in the display if 3 channel
stereo has been selected.
OFF means the audio system is in normal
stereo mode.
168
1. Press MENU.
2. Select the menu for the present sound
source and press ENTER.
3. Select sub bass and press ENTER. A
check in the box (in the display) indicates
that it is activated.
Equalizer, front
(certain models)
Fine adjustment of the sound in the front
speakers:
1. Press MENU.
2. Select the menu for the present sound
source and press ENTER.
3. Select Sound settings in the menu and
press ENTER.
Fine adjustment of the sound in the rear
speakers:
1. Press MENU.
2. Select the menu for the present sound
source and press ENTER.
3. Select Sound settings in the menu and
press ENTER.
4. Select Equalizer rear and press ENTER.
5. Use the navigation button or TUNING
knob to set the level.
6. Use the navigation button to select the
next frequency. Five frequencies can be
adjusted.
7. Press ENTER to save any changes and
exit.
8. Press EXIT to exit without saving any
changes made.
Infotainment
Radio functions
•
Press the left or right arrow on the
navigation button and hold it in. The
radio scans slowly in the selected
direction and increases tempo after a
few seconds. Release the button when
the desired frequency appears in the
display.
If the frequency needs adjusting, press one of
the arrows briefly.
Storing stations
To store a selected station under one of the
station setting buttons 0-9:
Station search
1. Select radio mode using the AM/FM
button.
2. Start the search by pressing Auto for
longer than 2 seconds.
3. Autostoring appears in the display and a
number of stations with strong signals
(max. 10) from the set frequency band
will be stored in the autostore memory. If
there are no stations with sufficient
signal strength, No stn found is shown.
The stored stations can be found using the
buttons 0-9.
When the radio is in Autostore mode, Auto is
shown in the display. The text disappears
when you return to the ordinary radio mode.
Return to the standard radio mode by
pressing the AM/FM button, EXIT or by
pressing Auto for less than 0.7 seconds.
1. Select radio mode AM, FM1 or FM2
using the AM/FM button.
2. Briefly press the left or right arrow on the
navigation button to search for the next
strong station.
3. Press one of the arrows again to make a
new search.
1. Set the desired station.
2. Press the button under which the station
is to be stored and keep it held in. The
sound will disappear for a few seconds
and Station stored will appear in the
display.
Up to 10 stations can be stored in AM, FM1
and FM2, a total of 30 stations.
Manual station searching
Automatic storage of stations
Scanning
There are two ways of searching for a station
manually.
This function automatically searches and
stores up to ten strong AM or FM stations in
a separate memory. If more than ten stations
are found, the ten strongest are stored. This
function is especially beneficial in areas in
which you are not acquainted with radio
stations or their frequencies.
Scanning for a station:
1. Select radio mode using the AM/FM
button.
2. Press SCAN. Scan is shown in the
display
3. Press the SCAN or EXIT button to exit.
canning then continues.
•
Turn the TUNING knob to find the
required frequency
Return to the Autostore mode:
• To access the latest saved stations,
briefly press AUTO and then select the
channel using the buttons 0-9.
169
Infotainment
This function automatically searches for the
next strong AM or FM station signals. When
the radio finds a station, scanning is
interrupted for approximately 8 seconds. S
PI searching (automatic search
for transmitter)
PI search is shown in the display when
reception is poor. The radio automatically
searches for the strongest transmitter for the
set radio channel. PI-searching Exit to cancel
is displayed until a station is located or PIsearching is switched off.
Radio Data System - RDS
RDS is a system which links specific network
transmitters together. It is used, for example,
to set the correct frequency irrespective of
the transmitter to which the car occupants
are listening or the active audio source (e.g.
CD). The system can also be used for
receiving traffic information and for finding
broadcasts of a specific type. Radio text is
also a component of RDS. A radio station can
transmit information about the radio program
broadcasting.
NOTE! Certain radio stations do not use
RDS or only use specific parts of RDS
broadcast possibilities.
170
News
Program coded messages (such as news
from RDS stations) will interrupt other audio
sources using the volume setting for this
specific purpose. As soon as the news
broadcast is finished, the audio system
returns to the previous audio source and
resumes the previous volume setting.
Setting News:
1. Select radio mode using the AM/FM
button.
2. Press MENU.
3. Select the menu for the present sound
source and press ENTER.
4. Select News in the menu and press
ENTER.
5. Select News station.
6. Select News from present station
News is displayed. If you do not wish to listen
to a news item in progress, press the EXIT
button. The News function remains active
and the radio waits for the next news
programme. Deactivate the function: Select
News again and press ENTER.
Select Exit for news from present station.
1. Select radio mode using the AM/FM
button.
2. Activate the station from which news is
to be received.
3. Press MENU.
4. Select Advanced sound settings and
press ENTER.
5. Select News station and press ENTER.
6. Select News from the present station
and press ENTER.
Traffic information - TP Station
Traffic information from RDS stations
interrupts other audio sources in order to
broadcast . The message is heard at the
volume set for this specific purpose. As soon
as the message ends, the audio system
returns to the previous audio source and
resumes the previous volume setting.
Setting traffic information:
1. Press MENU.
2. Select the menu for the present sound
source.
3. Select TP and press ENTER.
TP is shown in the display when this function
is active. If the set station can transmit traffic
information, TP))) is shown in the display. If
you do not wish to listen to a traffic item in
progress, press the EXIT button.
The TP function, however, remains active and
the radio waits for the next traffic bulletin.
Infotainment
Set traffic information from a special channel:
1. Select radio mode using the AM/FM
button.
2. Activate the station from which traffic
information is to be received.
3. Press MENU. Select the menu for the
present sound source and press ENTER.
4. Select Advanced radio settings in the
menu and press ENTER.
5. Select TP and press ENTER.
6. Select TP Station and press ENTER.
7. Select TP and present station.
Deactivate TP station:
1. Press MENU. Select the menu for the
present sound source and press ENTER.
2. Select Advanced radio settings in the
menu and press ENTER.
3. Select TP and press ENTER.
4. Select TP Station and press ENTER.
5. Select TP from all stations and press
ENTER.
171
Infotainment
TP searching
Alarm
This function allows you to listen to traffic
information when travelling between different
areas and countries without needing to select
a station.
The alarm is transmitted automatically. The
function cannot be deactivated. ALARM! is
shown in the radio display when an alarm
message is sent. The function is used to warn
motorists of serious accidents or disasters.
1.
2.
3.
Press MENU.
Select present source.
Select Advanced radio settings in the
menu and press ENTER.
4. Select TP and press ENTER.
5. Select TP searching and press ENTER.
Deactivate the function: Select TP searching
and press ENTER.
Radio text
Some RDS stations send information about
programme content, artists, etc.
Display information with text in the display.
1. Press MENU. Select the menu for the
relevant sound source. Press ENTER
(the current sound source is always
marked in the menu if the audio system is
on).
2. Select Radio text in the menu and press
ENTER.
Deactivate:
Select Radio text again and press ENTER.
172
Programme type - PTY
Use the PTY function to select between the
different programme types.
3. Press MENU. Select the menu for the
present sound source and press ENTER.
4. Select PTY from the menu and press
ENTER.
5. Select Display PTY and press ENTER.
The set station’s PTY type will be shown
in the display.
NOTE! Not all radio stations have a PTY
designation.
Programme type
display
Shown in the
Current affairs
Current affairs
Information
Information
Sport
Sport
Education
Education
Theatre
Theatre
Culture and Art
Culture
Science
Science
Varied chat
Entertainment
Pop music
Pop music
Rock music
Rock music
Easy listening
Easy listening
Light classical
Light classical
Classical music
Classical music
Other music
Other music
Weather
Weather
Economics
Economics
For children
For children
Social questions
Social questions
Religion
Spiritual issues
Phone-in
Phone-ins
Travel and holiday
Travel and holiday
Infotainment
Leisure and hobby
hobby
Leisure and
Jazz music
Jazz music
Country music
Country music
National music
National music
Golden oldies
Golden oldies
Folk music
Folk music
Documentary
Documentary
Search for a specific programme
type
Search through the entire wave band:
1. Select FM 1 or FM 2 and press the
MENU button.
2. Select the menu for the present sound
source and press ENTER.
3. Select PTY and press ENTER.
4. Scroll to Select PTY and press ENTER.
5. Press ENTER for one or more of the
listed programme types. The PTY
symbol in the display lights up when the
first selection is made and the radio
continues in standby for PTY.
6. Press EXIT to go back.
7. Select Search PTY and press ENTER. If
the radio finds a station with the
selected programme type, it is played
through the speakers.
8.
If the radio finds a station that is
unsuitable, continue the search with the
left or right arrow on the navigation
button.
9. If no stations with the selected
programme type are found, the radio
resumes its previous frequency.
PTY mode is then in standby mode until the
selected type of programme begins
transmission. When this happens, the radio
automatically switches to the station
transmitting the selected programme type.
To deactivate PTY standby mode, select
Reset all PTYs. The PTY symbol is removed
from the display and the radio resumes
normal mode.
PTY standby
To continue with the radio in PTY standby,
repeat steps 1-6.
Automatic frequency upda-ting
The AF function is usually active and makes
sure that the strongest available transmitter
for a radio station is used.
1. Press MENU. Select the menu for the
present sound source and press
ENTER.
2. Select Advanced radio settings in the
menu and press ENTER.
3. Select AF and press ENTER.
Reactivate: Select AF and press ENTER.
Regional radio program
The regional-function is normally deactivated.
When the function is activated a regional
transmission can be listened to despite a
weak signal.
Activate regional radio program:
1. Press MENU. Select the menu for the
present sound source and press
ENTER.
2. Select Advanced radio settings in the
menu and press ENTER.
3. Select Regional and press ENTER.
4. REG is shown in the display.
Deactivate:
Select REG again and press ENTER.
EON - Local/Distant (Enhanced
Other Networks)
With EON activated traffic information and
news broadcasts interrupt radio programs.
EON is normally in the distant position. The
function has three levels:
• Local - Only interrupts if the signals are
strong.
•
Distant - Interrupts even if the signals
are weak.
•
Off - Not activated.
Activate EON:
1. Press MENU.
2. Select the menu for the present sound
source and press ENTER.
173
Infotainment
3.
4.
5.
Select Advanced radio settings in the
menu and press ENTER.
Select EON and press ENTER.
Select Local, Distant or Off and press
ENTER.
Resetting RDS functions
Restores all radio settings to the original
factory settings.
1. Press MENU. Select the menu for the
present sound source and press
ENTER.
2. Select Advanced radio settings in the
menu and press ENTER.
3. Select Reset in the menu and press
ENTER.
4. Press ENTER again to confirm.
174
Infotainment
CD/MD (option)
IMPORTANT!
• Use only 12 cm CDs, no smaller!
• Do not use CDs with adhesive disc
labels. The heat from the CD player
can cause the label to come loose
from the disc. The CD player could
be damaged.
Starting the CD/MD player
(option)
Start the CD/MD player by pressing the CD/
MD button. Insert a disc in the player.
CDs
If the quality of the CD does not comply with
the requirements of standard EN60908 or if
it has been recorded using poor equipment,
sound quality may be poor or playback
interrupted
3. RND is shown in the display as long as
the function is activated.
Select Random again and press ENTER or
press EXIT to deactivate.
Scan
Scan plays the first ten seconds of each
track.
1. Press SCAN.
2. Press EXIT to play the relevant track.
Changing tracks
Disc text
Press the left or right arrow on the navigation
button to skip to the previous or next track.
The track number is shown in the display. The
TUNING knob (or keypad unit in the steering
wheel) can also be used for this purpose.
Some CDs have title information. The
information is displayed as text in the display.
Fast forward/rewind
Press and hold down the left or right arrows
on the navigation button to search within a
track or the whole disc. The search continues
as long as the buttons are held in.
Random
This function chooses a CD track randomly.
1. Press MENU. Select the menu for the
present sound source and press ENTER.
2. Select Random in the menu and press
ENTER.
Activate Disc text:
1. Press MENU. Select the menu for the
present sound source and press ENTER.
2. Select Disc text in the menu and press
ENTER.
3. If information is stored on the disc, it will
now appear in the display.
Deactivate:
• Select Disc text and press ENTER.
CD/MD eject
Press the eject button to eject the disc. For
traffic safety reasons, an ejected CD remains
out for 12 seconds. The player will then draw
the disc back in and the player will switch to
pause mode. (does not apply to MD). Press
CD/MD to reactivate the player.
175
Infotainment
CD changer (option)
CDs
Fast forward/rewind
If the quality of the CD does not comply with
the requirements of standard EN60908 or if
it has been recorded using poor equipment,
sound quality may be poor or playback
interrupted.
Press and hold down the left or right arrows
on the navigation button to search within a
track or the whole disc. The search continues
as long as the buttons are held in.
IMPORTANT!
• Use only 12 cm CDs, no smaller!
• Do not use CDs with adhesive disc
labels. The heat from the CD player
can cause the label to come loose
from the disc. The CD player could
be damaged.
Starting the CD changer
The CD changer can hold up to six discs.
Selecting position
Starting the CD changer:
1. Press the CD/MD button.
2. Select an empty position using the 1-6
buttons (or up/down using the navigation
button). The display shows which
positions are empty.
3. Insert a disc into the changer.
Ensure that Insert disc is displayed before
inserting a new disc.
The disc to be played is selected using the
buttons 1-6 or by pressing the up or down
arrow on the navigation button. The number
of the disc and track are shown in the display.
176
Changing tracks
Press the left or right arrow on the navigation
button to skip to the previous or next track.
The track number is shown in the display.
The TUNING knob (or keypad unit in the
steering wheel) can also be used for this
purpose.
Scan
Scan plays the first ten seconds of each
track.
1. Press SCAN.
2. Press EXIT to play the relevant track.
Random
Plays tracks from the disc in random order.
1. Press MENU. Select the menu for the
present sound source and press ENTER.
2. Select Random in the menu and press
ENTER.
3. Select Single disc or All discs for the
player to randomly choose from one or all
discs in the CD changer.
4. RND or RND ALL is shown in the display
while the function is active.
Press the right arrow on the navigation button
to select the next random track. Deactivate:
Press EXIT.
NOTE! You can only select the next random
track on the current disc.
Infotainment
Disc text
Some CDs have title information. The
information is displayed as text in the display.
must then be removed, or the function is
cancelled.
Activate Disc text:
1. Press MENU. Select the menu for the
present sound source and press ENTER.
2. Select Disc text in the menu and press
ENTER.
3. If information is stored on the disc, it will
now appear in the display.
Deactivate:
• Select Disc text and press ENTER.
CD - eject, 1 disc
Press the eject button to eject the disc.
For traffic safety reasons, the CD remains out
for 12 seconds. The player will then draw
back in the disc and switch to pause mode.
Press CD/MD to reactivate the player.
CD eject, all discs
Press the eject button (for longer than 2
seconds) to initiate the eject function. The
entire magazine is emptied, disc by disc.
Eject all is shown in the display.
This function can only be activated when the
car is stationary and is interrupted if the car
starts to move. For traffic safety reasons, the
ejected CD remains out for 12 seconds. It
177
Infotainment
Menu settings and selections - Audio
FM1/FM2 menu
1.
2.
3.
3.1.
3.1.1.
3.1.2.
3.1.3.
3.1.4.
3.1.5.
3.1.6.
3.1.7.
3.2.
3.3.
4.
5.
5.1.
5.1.1.
5.1.2.
5.2.
5.3.
5.4.
5.5.
5.5.1.
5.5.2.
5.5.3.
5.6.
6.
6.1.
6.1.1.
178
News Off/On*
TP Off/On*
PTY
Select PTY
Reset all PTY's
Current affairs On*/Off
Information On/Off*
Sport On/Off*
Education On/Off*
Theatre On/Off*
Documentaries On/Off*
Search PTY
Display PTY On/Off
Radio text On /Off*
Advanced radio settings
TP
TP station
TP search Off/On*
News station
AF On*/Off
Regional On/Off*
EON
Off
Local
Distant*
Reset all
Sound settings
Surround AM/FM (option)
Dolby Pro Logic II
6.1.2. 3 channel stereo
6.1.3. Off*
6.2.
Surround CD/MD (accessory*)
6.2.1. Dolby Pro Logic II
6.2.2. 3 channel stereo
6.2.3. Off
6.3.
Sub-bass On*/Off (accessory)
6.4.
Equalizer front (certain models)
6.5.
Equalizer rear (certain models)
6.6.
Speed compensation
6.6.1. Low
6.6.2. Medium
6.6.3. High
6.7.
Reset all
*Default/Factory settings
AM menu
7.
7.1.
7.1.1.
7.1.2.
7.2.
7.2.1.
7.2.2.
7.2.3.
7.3.
7.4.
7.5.
7.6.
7.6.1.
7.6.2.
Sound settings
Surround AM/FM (option)
Dolby Pro Logic II
3-channel stereo Off*
Surround CD/MD (accessory)
Dolby Pro Logic II
3 channel stereo
Off
Sub-bass On*/Off (accessory)
Equalizer front (certain models)
Equalizer rear (certain models)
Speed compensation
Low
Medium
7.6.3. High
7.7.
Reset all
* Default/Factory settings
CD menu
1.
Random
2.
News (Off*)
3.
TP (Off*)
4.
Sound settings
4.1.
Surround AM/FM (option)
4.1.1. Dolby Pro Logic II
4.1.2. 3 channel stereo
4.1.3. Off*
4.2.
Surround CD/MD (accessory)
4.2.1. Dolby Pro Logic II
4.2.2. 3 channel stereo
4.2.3. Off
4.3.
Sub-bass (On*) (option)
4.4.
Equalizer front (certain models)
4.5.
Equalizer rear (certain models)
4.6.
Speed compensation
4.6.1. Low
4.6.2. Medium
4.6.3. High
4.7.
Reset all
* Default/Factory settings
Infotainment
CD changer menu
1.
Random
1.1.
Off*
1.2.
One disc
1.3.
All discs
2.
News (Off*)
3.
TP (Off*)
4.
Disc text (Off*)
5.
Sound settings
5.1.
Surround AM/FM (option)
5.1.1. Dolby Pro Logic II
5.1.2. 3 channel stereo
5.1.3. Off*
5.2.
Surround CD/MD (accessory)
5.2.1. Dolby Pro Logic II*
5.2.2. 3 channel stereo
5.2.3. Off
5.3.
Sub-bass (On*) (option)
5.4.
Equalizer front (certain models)
5.5.
Equalizer rear (certain models)
5.6.
Speed compensation
5.6.1. Low
5.6.2. Medium
5.6.3. High
5.7.
Reset all
* Default/Factory settings
4.
Disc text (Off*)
5.
Sound settings
5.1.
Surround AM/FM (option)
5.1.1. Dolby Pro Logic II
5.1.2. 3 channel stereo
5.1.3. Off*
5.2.
Surround CD/MD (accessory)
5.2.1. Dolby Pro Logic II*
5.2.2. 3 channel stereo
5.2.3. Off
5.3.
Sub-bass (On*) (option)
5.4.
Equalizer front (option)
5.5.
Equalizer rear (option)
5.6.
Speed compensation
5.6.1. Low
5.6.2. Medium
5.6.3. High
5.7.
Reset all
* Default/Factory settings
CD/MD menu
1.
2.
3.
Random
News (Off*)
TP (Off*)
179
Infotainment
Telephone functions (option)
Telephone system components
180
Infotainment
1. Antenna
The antenna is on the roof.
2. Steering wheel keypad
The majority of the telephone functions
can be controlled using the keypad.
When the telephone is active, the keypad
can only be used for telephone functions.
There is always telephone information in
the display when the telephone is
activated.
3. Microphone
The hands free microphone is integrated
in the roof console beside the rear-view
mirror.
4. Control panel
All functions (except call volume) can be
controlled from the keypad in the control
panel. The display shows menu
functions, messages, telephone
numbers, etc.
5. Privacy handset (option)
6. SIM card-The SIM card is placed in a
holder in the glove compartment.
•
Switch off the system near blasting
work.
•
Let only authorised personnel service
the telephone system.
Emergency calls
Emergency calls to alarm centres can be
made without a SIM card as long as there is
coverage by a GSM operator.
Making an emergency call:
1. Activate the telephone.
2. Ring the emergency number that applies
to your region (within EU: 112).
3. Press ENTER.
Speaker
The telephone uses the speaker in the
driver’s door (or the centre speaker of the
audio system, if there is one).
General
Always put traffic safety first.
• If the driver needs to use the privacy
handset, park the car in a safe place
first.
•
Switch off the telephone system when
refuelling the car.
181
Infotainment
Telephone functions
Double SIM card
Many network operators offer double SIM
cards, one for your car and one for another
telephone. A double SIM card allows you to
have the same number for two different
telephones. Ask your network operator about
the offers available and the use of double SIM
cards.
Specifications
SIM card
The telephone can only be used with a valid
SIM card (Subscriber Identity Module). The
card is managed by different network
operators. Contact your network operator if
you experience difficulties with the SIM card.
Insert the SIM card to start using the
telephone.
1. Switch off the telephone.
2. Open the glovebox and the cover for the
SIM card holder.
3. Pull out the SIM card holder.
4. Place the card metal side up. Ensure that
the bevelled corner of the SIM card
matches the bevel of the holder.
5. Carefully press in the holder again.
182
Output
2W
SIM card
Small
Memory positions
255
SMS (Short Message
Service)
Yes
Computer/Fax
No
Dual band
Yes (900/
1800)
The number of SIM card memory positions
varies depending on the subscription.
IMEI number
To restrict a telephone the network operator
must be informed of the telephone's IMEI
number. This is a 15 digit serial number
programmed into the telephone. To display
this number, press *#06#. Make a note of
this number and keep it in a safe place.
Infotainment
1. PHONE – On/off/standby.
2. MENU – Open the main menu.
3. ENTER – Accept a call, make a menu
selection or activate the telephone from
standby mode. A short press of the
ENTER button displays the last dialled
number.
4. EXIT – Terminate/reject a call, scroll back
in the menu, cancel a selection or erase
entered digits/characters.
5. Navigation button – Scroll up or down in
the menus, scroll forwards or back when
entering text and digits.
6. Display
7. Number and character buttons as well as
menu shortcuts.
8. VOLUME – Controls the background
noise from the radio etc. during a call.
Steering wheel keypad
1. ENTER – Accept a call, scroll the menu
or activate the telephone from standby
mode. One press of the ENTER button
displays the last dialled number.
2. EXIT – Terminate/reject a call, scroll back
in the menu, cancel a selection or erase
entered digits/characters.
3. Volume - Increase/decrease call volume
during a call.
4. Navigation button – Scroll up or down in
the menus, scroll forwards / back when
entering text and digits.
Control panel centre console
183
Infotainment
Switch
When the telephone system is active or in
standby mode, a handset is shown in the
display.
If the car’s ignition is switched off while the
telephone system is on, the system will be on
the next time the ignition is switched on. No
calls can be received when the telephone
system is switched off.
Activate:
1. Press PHONE to start the telephone
system.
2. Enter the PIN code and press ENTER.
Switch off:
• Hold PHONE in to switch off the
telephone system.
Volume reduction during a
telephone call
If the telephone rings when the radio is
switched on, the volume is lowered when the
call is answered. When the call is concluded,
the volume returns to the previously set level.
It is possible to adjust radio volume when the
telephone is engaged in order to maintain the
new volume level when the call is ended. The
audio volume can be switched off completely
during a telephone call. See menu 5.5.3.
This function only applies to the Volvo
integrated telephone system.
Standby mode
Standby:
• Press PHONE or EXIT to keep the
telephone system in standby mode.
Calls can be received while the audio system
is active and information from the audio
system sources is shown in the display. The
telephone must be in active mode to use the
other functions of the telephone system.
•
Menu shortcuts
Press PHONE briefly to reactivate the
system.
NOTE! With the audio model Performance,
it is not possible to listen to the radio, CD, MD
or receive traffic messages during a
telephone call.
In the menu system, you can use numbers
instead of the arrows and ENTER to select
the right menu on the main menu level. Each
menu selection is numbered. The numbers
are shown in the display together with the
menu alternative.
Traffic safety
For reasons of safety, the menu system
cannot be accessed at speeds in excess of 8
184
km/h (5 mph). Only activities started in the
menu system can be completed. The speed
limiter can be disconnected using menu
function 5.6 1 Menu lock.
IDIS
(Intelligent Driver Information System) The
IDIS system allows the priority of incoming
telephone calls and SMS messages to be
reduced so that the driver can concentrate on
driving. Incoming calls and SMS messages
can be delayed for 5 seconds before they are
connected. Missed calls are shown in the
display. IDIS can be disconnected using
menu function 5.6.2
Making and receiving calls
To call:
• Dial the number and press ENTER on
the steering wheel or the control panel
keypads or lift the handset.
To receive a call:
• Press ENTER (or lift the handset).
Automatic Answer can also be used.
See menu function 4.3.
The car audio system can be muted
automatically while a telephone conversation
is in progress. See menu alternative 5.5.3.
Ending a call
Press EXIT on the steering wheel or control
panel keypad or hang up the handset. The
audio system resumes its previous activity.
Reject an incoming call by pressing EXIT.
Infotainment
To switch to handsfree without ending the
call:
• Press the right arrow on the steering
wheel keypad (or the menu buttons in
the control panel) and select Handsfree.
Press ENTER and replace the handset
in its cradle. If the handset is already
removed from its cradle, the other party
will be audible in the handsfree system.
Press the MENU button, scroll to
Handset and press ENTER in order to
transfer to the handset.
Last dialled number
Privacy handset (option)
Making a call using the handset:
1. Select the desired telephone number
using the centre console keypad and lift
the handset to make the call. Press the
handset down before lifting.
2. The call is cancelled when the handset is
replaced in the holder.
Adjust the volume using the dial on the side
of the handset.
The telephone automatically stores the last
telephone numbers/names dialled.
Calling the last dialled number:
1. Press ENTER on the keypad on the
steering wheel or control panel (when in
active mode).
2. Use the menu buttons to scroll forward
or back through the last numbers dialled.
These are shown in the display.
3. Press ENTER.
Speed dialling
A number stored in the phone book can be
linked to a speed dial button
(1-9).
1. Select Phone book from the menu and
press ENTER
2. Scroll to speed dial, menu 3.4, and press
ENTER.
3. Select which number is to be the speed
dial number. Press ENTER to confirm.
4. Search for the desired name or
telephone number in the phone book.
Press ENTER to select.
Hold in the desired speed dial button for
approximately two seconds to make the call
or press the number briefly followed by
ENTER.
NOTE! When the telephone is switched on,
it takes a while before speed dialling is
available. Menu 3.4.1 must be activated to
use a speed dial number
Call waiting
A two-tone signal during a telephone call
indicates that there is another incoming call.
The display shows: Answer?
To receive a call:
1. Press ENTER. Your current call will be
put in hold mode.
2. Select Hold/Resume to finish the call
and return to a call on hold.
To reject necessary call: Press EXIT.
Exit the current call: Press EXIT. The function
can be de-selected in the menu.
Functions during a call
Several functions are available during a call.
185
Infotainment
Use the navigation button to scroll and press
ENTER to make a selection.
Phone book
Show phone book
Secret mode/
Secret mode
off
Secret mode
Park/Resume
Choose if the current
call is to be held or
resumed
Control the call volume during the call by
pressing the buttons with the large or small
loudspeaker on the keypad on the steering
wheel.
Handsfree/
Handset
Use the handset or
handsfree
When the telephone is activated, the steering
wheel keypad only controls the telephone
functions.
Phone book
Show phone book
Call volume
Several functions are available during a call
while another call is on hold.
Use the navigation button to scroll and press
ENTER to make a selection.
Secret mode/
Secret mode
off
Secret mode
Handsfree/
Handset
Use the handset or
handsfree
Three-way
calling
Conference call
(provides further
options)
Switch
186
Select between two
calls
The telephone must be in standby mode to
control the audio system using the steering
wheel keypad.
Phone book
Telephone numbers and names can be
stored in either the telephone memory or the
SIM card memory.
If the number of the person calling is stored in
the phone book, the name of the caller will be
shown in the display.
3.
4.
5.
6.
Scroll to Enter item and press ENTER.
Enter a name and press ENTER.
Enter a number and press ENTER.
Select the menu to which it should be
saved and press ENTER.
Copy between the SIM card and Phone
book
Copy from the SIM card to the phone card:
•
Select MENU.
•
Select Phone book.
•
Select Copy all.
•
Select From SIM card to Phonebook
and press ENTER.
It is also possible to copy from the phone
card to
SIM card.
Erase names
Erase from the phone book:
• Select MENU.
•
Select Phone book.
•
Select Search.
The telephone memory can store up to 255
names.
•
Specify the first letter of the name (or
the entire name) and press ENTER
Storing telephone numbers with names:
•
1. Press MENU.
2. Select Telephone book and press
ENTER.
Scroll to the name to be erased and
press ENTER.
•
Select Erase to remove the name.
Infotainment
Enter a name/message
Press the button with the relevant character.
Press once for the first character, twice for
the second character and so on. Press 1 for
space.
1
2
3
4
5
6
7
8
9
*
0
#
EXIT
space 1- ? ! , . : " ' ( )
abc2äåàæç
def3èé
ghi4ì
jkl5
mno6ñöòØ
pqrs7ß
tuv8üù
wxyz9
if you enter two letters in a row
from the same button, press *
between them or wait a few
seconds
+0@*#&$£/%
switch between upper and lower
case
erase the last entered character.
If you press this for a long time,
the entire number or text is
deleted.
Interrupting text input:
1. Erase all entered characters with a long
press on the EXIT button.
2. Return to the menu with an additional
long press on the EXIT button.
Calling from the memory
1.
2.
3.
4.
Press MENU
Scroll downwards using the navigation
button (or the left arrow button on the
steering wheel to search the phone
book)
Press ENTER. Scroll to the desired
name using the navigation button or
press the first letter of the name (or
enter the entire name). Press ENTER
Press ENTER to dial the selected
number.
187
Infotainment
Menu settings and selections - Telephone
Telephone menu
1.
1.1.
1.2.
1.3.
1.4.
1.4.1.
1.4.2.
1.4.3.
1.4.4.
1.5.
1.5.1.
1.5.2.
1.5.3.
1.5.4.
2.
2.1.
2.2.
2.3.
2.3.1.
2.3.2.
2.3.3.
3.
3.1.
3.2.
3.3.
3.3.1.
3.3.2.
3.4.
3.4.1.
188
Call log. - CALL
Missed calls
Received calls
Outgoing calls
Erase list
All calls
Missed calls
Received calls
Outgoing calls
Call duration
Last call
Number of calls
Total time
Reset time
Messages
Read
Write
Message settings
SMSC number
Validity period
Message type
Phone book
Enter item
Search
Copy all
SIM to telephone
Telephone to SIM
Speed dial
Active
3.4.2.
3.5.
3.6.
3.7.
4.
4.1.
4.2.
4.3.
4.4.
4.5.
4.5.1.
4.5.2.
4.5.3.
4.5.4.
4.5.5.
4.5.6.
4.5.7.
5.
5.1.
5.1.1.
5.1.2.
5.2.
5.2.1.
5.2.2.
5.2.3.
5.2.4.
5.2.5.
5.2.6.
5.2.7.
5.2.8.
5.2.9.
Select number
Empty SIM
Empty telephone
Memory status
Call options
Transmit number
Call waiting
Automatic answer
Automatic redial
Call divert
All calls
When busy
No reply
Unobtainable
Fax calls
Computer calls
Cancel all diverts
Tel. settings
Network selection
Automatic
Manual
Language
English UK
English US
Español
Français CAN
Français FR
Italiano
Nederlands
Portuguës BR
Portuguës P
5.2.10.
5.2.11.
5.2.12.
5.2.13.
5.3.
5.3.1.
5.3.2.
5.3.3.
5.4.
5.4.1.
5.4.2.
5.5.
5.5.1.
5.5.2.
5.5.3.
5.5.4.
5.6.
5.6.1.
5.6.2.
5.7.
Suomi
Svenska
Dansk
Deutsch
SIM security
On
Off
Automatic
Change codes
PIN code
Telephone code
Volume
Ringer volume
Ringer tone
Mute radio
Message beep
Traffic safety
Menu lock
IDIS
Factory settings
Menu options, description
Menu 1. Call log
1.1.
Missed
calls
List of missed calls. You
can choose to call, erase
or store the number in the
phone book.
Infotainment
1.2.
Received
calls
List of received calls. You
can choose to call, erase
or store the number in the
phone book.
2.1. Read
1.3.
Outgoing
calls
List of dialled numbers. You
can choose to call, erase or
store the number in the
phone book.
2.2. Write
1.4. Erase
list
Erase the lists found in the
menus 1.1, 1.2 and 1.3 as
below.
1.4.1. All
1.4.2. Missed
1.4.3. Received
1.4.4. Outgoing
1.5. Call
duration
Call duration of all calls or
of the latest call.
1.5.1. Last call
1.5.2. Number of calls
1.5.3. Total time
1.5.4. Reset time
The telephone code is
required to reset the call
timer
(see Menu 0.4)
2.3.
Message
setting
3.1. Enter
item
Store names and numbers
in the phone book. See the
section on phone book
functions for more
information.
3.2. Search
Search for a name in the
phone book
Menu 2. Messages
Menu 3. Phone book
Menu 4. Call options
Received text messages.
Select whether to erase,
forward, change or save
the entire message or
parts of it.
Write a message using the
keypad unit. Choose
whether to save or send it.
Enter the number (SMSC
number) of the message
centre to which you want
your messages transferred
as well as how long they
are to be saved at the
message centre.
2.3.1. SMSC number
2.3.2. Validity period
2.3.3. Message type
Contact your network
operator for information
about these settings and
for an SMSC number.
Normally, these settings
should not be altered.
3.3. Copy
all
Copy the telephone
numbers and names from
the SIM card to the
telephone memory.
3.3.1. From SIM to
telephone memory
3.3.2. From telephone to
SIM memory.
3.4. Speed
dial
A number stored in the
telephone book can be
stored as a speed dial
number.
3.5. Empty
SIM
Select to erase the entire
memory of the SIM card
3.6. Empty
memory
Erase the entire telephone
memory.
3.7.
Memory
status
Shows how many
positions are occupied by
names and numbers in the
SIM card and telephone
memory. The table
displays how many of the
available spaces are
occupied, e.g 100(250).
Menu 5. Telephone settings
189
Infotainment
4.1.
Transmit
number
Select whether or not your
own number should be
displayed to the person
you call. Contact your
network operator
regarding ex-directory
numbers.
5.1.
Network
selection
Choose a network
automatically or manually.
The selected operator is
shown in the display in the
telephone’s basic mode.
5.1.1. Auto
5.1.2. Manual
4.2. Call
waiting
Select whether or not you
want to be alerted during
a phone call that there is
another incoming call.
5.2.
Language
4.3.
Automatic
answer
To automatically receive
an incoming call:.
4.4. Redial
Call a previously engaged
number.
4.5.
Transfer
Choose when and what
type of calls are to be
diverted to a specified
telephone number.
4.5.1. All calls (this setting
only applies during the call
in progress)
4.5.2. When busy
4.5.3. No reply
4.5.4. Unobtainable
4.5.5. Fax calls
4.5.6. Computer calls
4.5.7. Cancel all diverts
Select the telephone
language.
5.2.1. English UK
5.2.2. English US
5.2.3. Español
5.2.4. Français CAN
5.2.5. Français FR
5.2.6. Italiano
5.2.7. Nederlands
5.2.8. Portuguës BR
5.2.9. Portuguës P
5.2.10. Suomi
5.2.11. Svenska
5.2.12. Dansk
5.2.13. Deutsch
190
5.3. SIM
security
5.4. Change
codes
Change the PIN code or
telephone code 5.4.1 PIN
code 5.4.2.Telephone
code (use 1234 until you
change to your own
code). The telephone
code is used to reset the
call timer. Make a note of
your code and save it in a
safe place.
5.5. Volume
5.5.1. Volume. Adjust the
ring tone volume.
5.5.2. Ring tone. There
are seven different ring
tones.
5.5.3. Mute radio. On/Off
5.5.4. Message beep
5.6. Traffic
information
Disengaging the speed
function , i.e. the entire
menu selection can be
made available while
driving.
5.6.1. Menu lock
5.6.2. IDIS
The IDIS function can be
disconnected. Incoming
calls will not be delayed,
irrespective of whether the
car is being driven or not.
5.7. Factory
settings
Return to the system’s
factory settings.
Select if the PIN code
should be on, off or if the
telephone should
automatically give the PIN
code.
5.3.1. On
5.3.2. Off
5.3.3. Automatic
Specifications
Specifications
Type designations
Measurements, weights, capacities
Lubricants
Catalytic converter
Fuel
Electrical system
Engine specifications
192
193
195
197
198
199
200
191
Specifications
Type designations
When contacting your Volvo dealer and when
ordering spare parts and accessories for your
car, it makes things easier if you know your
car’s type designation, vehicle identification
number and engine number.
192
1.
The VIN (Type and model year
designations and chassis number) is
stamped in the engine compartment
underneath the windscreen
2.
Type designation, chassis number,
maximum permissible weights, codes
for colour and upholstery and type
approval number (on the right-hand Bpost)
3.
Engine type designation, component
and serial number (on the right hand
side of the engine)
4.
Gearbox type designation and serial
number,
(a) manual gearbox (on the front)
(b) automatic gearbox (on the top).
Specifications
Measurements, weights, capacities
Measurements
Capacities
Length:
447 cm
Fuel tank
litres
Width:
177 cm
Petrol
62
Wheelbase:
264 cm
Diesel
52
Front track:
154-155 cm
Rear track:
153-154 cm
Engine oil (with filter
replacement)
litres
2.4 + 2.4i
approx.
5.8
T5
approx.
5.8
2.0D
approx.
5.5
Weights
1.
Max. total weight
2.
Max. train weight (car+trailer)
3.
Max. front axle load
Gearbox oil
litres
4.
Max. rear axle load
Manual 5-speed
approx.
2.1
Manual 6-speed
approx.
2.0
Manual 6-speed diesel
approx.
1.7
Automatic
approx.
7.0
Permissible weight (excluding driver) =
Total weight – Curb weight
Weight specifications can be found on the
right-hand B-post.
Max. load, see registration papers
Maximum roof load:
75 kg
Maximum trailer weight:
1,500 kg
193
Specifications
Miscellaneous
litres
Windscreen washer
reservoir, 4-cyl +
diesel 5-cyl.
4
6,5
Air conditioning
gramme
Compressor oil
180-200
Refrigerant
500-600
Cooling system
Engine
litres
5 cyl, manual
gearbox
approx. 8.0
5 cyl, automatic gearbox
approx. 8.5
4 cyl. Diesel
9.5
All cooling systems are closed overpressure
systems. The thermostat starts opening at
90 ºC for petrol engines and at 82 ºC for
diesel engines.
194
Specifications
Lubricants
Oil grade
Engine oil ACEA A3/B3/B4 grade oil can
also be used. Oils with a viscosity of 0W-30
and 0W-40 must fulfil these oil grade
requirements.
In extreme driving conditions, select a fully
synthetic engine oil that provides the engine
with added protection.
Petrol engines
Recommended oil grade: ACEA A1/B1
Engine oil with grade designations ACEA A3/
B3/B4 or ACEA A5//B5 may also be used.
Diesel engines
Recommended oil grade:
WSS-M2C913B
Diesel engines
Recommended oil grade: WSSM2C913B
IMPORTANT!
Do not use extra additives. These can
damage the engine.
Volvo recommends Castrol® oil products.
Viscosity, (the table assumes constant air
temperature)
Viscosity
* Engine oil with a viscosity of 0W-30 and
0W-40 must fulfil ACEA A3/B3/B4 or ACEA
A5/B5.
Extreme driving conditions
In extreme driving conditions resulting in
abnormally high oil temperature or oil
consumption, such as alpine driving with a
great deal of engine braking or motorway
driving at high speed.
Petrol engines
Recommended oil grade: ACEA A5/B5
195
Specifications
Gearbox
Brake fluid
Manual gearbox (petrol engines)
Only use Volvo’s synthetic gearbox oil or
similar products with the same specifications.
Manual gearbox (diesel engines)
Use transmission oil WSD-M2C200-C only.
IMPORTANT!
Castrol's® gearbox oil may not be mixed
with any other gearbox oil.
Automatic gearbox
Only use Volvo recommended gearbox oil. Do
not mix with any other oil.
IMPORTANT!
If in doubt regarding the correct oil grade,
contact a Volvo workshop.
Power steering
Grade:
Only use Volvos
power steering oil or
products with similar
specifications.
Volume:
the system:
the reservoir:
196
approx. 1.2 litres
approx. 0.2 litres
Fluid type:
Brake fluid DOT 4+
Volume:
approx. 0.6 litres
Air conditioning
Refrigerant
R134a
Quantity
500-600 g*
Compressor oil
PAG
Quantity
180-200 g*
* The weight varies depending on the engine
type. Contact a Volvo workshop for the
correct information.
Specifications
Catalytic converter
Lambda sensorTM heated
oxygen sensor
The lambda sensor is part of a management
system intended to reduce emissions and
improve fuel economy.
Catalytic converter
The three-way catalytic converter (TWC) is
an additional part of the exhaust system. Its
purpose is to purify exhaust gases. The threeway catalytic converter (TWC) primarily
consists of a housing with two monoliths that
are designed so that the exhaust gases pass
through a honeycomb of channels. The
channel walls are lined with a thin layer of
platinum, rhodium and palladium. These
metals act as catalysts, i.e. they participate in
and accelerate a chemical reaction without
being used up themselves.
An oxygen sensor monitors the oxygen
content of the exhaust gases leaving the
engine. These values are fed into an
electronic system that continuously controls
the injectors. The ratio of air to fuel is
continuously adjusted. These adjustments
create optimal conditions for efficient
combustion, and together with the three-way
catalytic converter reduce harmful emissions
(hydrocarbons, carbon monoxide and nitrous
oxides).
197
Specifications
Fuel
Fuel consumption and carbon
dioxide emissions
Engine
Gearbox
Consumption in litres/100 km
Carbon dioxide emission (CO²) g/km
2.4i
Manual 5
8,5
203
Automatic
9,1
217
2.4
T5
2.0D
Manual 5
8,4
199
Automatic
9,1
217
Manual 6
8,7
208
Automatic
9,4
224
Manual 6
5,6
148
Official fuel consumption figures are based
on a standard driving cycle in accordance
with EU directive 80/1268 comb. Fuel
consumption figures may be altered if the car
is equipped with extra options which affect
car weight. The manner in which the car is
driven and other non-technical factors can
affect fuel consumption. Consumption is
higher and power output lower when driving
using fuel with an octane rating of 91 RON.
Petrol
The engine can be run with octane ratings of
91, 95 and 98 RON.
•
98 RON is recommended for maximum
effect and minimum fuel consumption.
•
95 RON can be used for normal driving.
•
91 RON should only be used as an
exception. However, the engine will not
be damaged by this fuel grade.
Standard DIN 51600. Min. 91 Octane RON
Unleaded.
Diesel
Standard SS-EN 590.
198
Specifications
Electrical system
General
Bulbs
12 volt system with a voltage regulated
alternating current generator. Single pole
system in which the chassis and engine block
are used as conductors. The negative pole is
connected to the chassis.
Battery
Voltage
12 V
12 V
12 V
Cold start
capacity
(CCA)
520 A
600 A*
700 A**
Reserve
capacity
(RC)
100 min 120 min 150 min
* Cars equipped with High Performance
audio level.
** Diesel cars with Premium Sound audio
level, fuel-driven heaters, Telematic, RTI or
Mobile Office. If the battery is replaced,
replace it with a battery of the same cold start
capacity and reserve capacity as the original
(see the decal on the battery).
Generator1 max.
current
120/150 A
Starter motor1,
power
1.4/1.9 kW
1
SV 8.5
Output
Socket
Cargo
compartment
5W
Bulbs
Dipped beam
55 W
H7 LL
Glovebox lighting
3W
BA 9
Main beam
55 W
HB3
Vanity mirror
1.2 W
SV 5.5
Bi-Xenon (option)
35 W
DS
Fog lamps
55 W
H11
Front parking
lamp
5 W LL
BAY15d
Side direction
indicator
5W
W 2.1 x
9.5d
Direction
indicators, front
(yellow)
21 W
BAU
15s
Direction
indicators, rear
(yellow)
21 W
BAU
15s
Front parking
lamp, rear
5 W LL
BA 15
Brake light
21 W LL
BA 15
Reversing lamp
21 W LL
BA 15s
Rear fog lamp
21 W LL
BA 15s
Number plate
lighting
5W
W 2.1 x
9.5d
Courtesy lighting
5W
SV 8.5
Depending on engine variant
199
Specifications
Engine specifications
Output (kW/rps)
2.4i
2.4
T5
2.0 D
B5244S4
B5244S5
B5254T3
D4204T
125/100
103/83
162/83
100/67
(hp/rpm)
170/6000
140/5000
220/5000
136/4000
Torque (Nm/rps)
230/73
220/67
320/25-80
340/33
(kpm/rpm)
23,4/4400
22,4/4000
32,6/1500-4800
34,7/2000
No. of cylinders
5
5
5
4
Bore (mm)
83
83
83
85
Stroke (mm)
90
90
93,2
88
Cylinder displacement
(dm³ or litres)
2,44
2,44
2,52
2,00
Compression ratio
10,3:1
10,3:1
9,0:1
18,5:1
Electrode gap (mm)
1,2
1,2
0,7-0,8
Tightening torque (Nm)
30
30
30
Spark plugs:
200
Index
A
ABS system ................................................. 103
ABS, indicator symbol ..................................36
Active Yaw Control ..................................... 105
Additional heater, diesel ...............................70
Air conditioning, ECC ...................................64
Air pressure .................................................. 123
Air quality system ...........................................65
Airbag .......................................................17, 19
Airbag, indicator symbol ...............................37
Airbag, inspection ..........................................27
Alarm .................................................................90
Alarm LED .......................................................90
Alarm signals ...................................................91
Alarm test .........................................................91
Aluminium rim .............................................. 122
Antenna ......................................................... 181
Anti-lock brakes ........................................... 103
Audio ............................................................. 164
Audio, control panel ................................... 165
Audio, display .............................................. 166
Audio, menu handling ................................ 166
Auto, ECC .......................................................64
Automatic car wash .................................... 134
Automatic re-locking .....................................87
B
Backrest, adjust .............................................72
Battery care .................................................. 149
Battery, overloading ......................................94
Battery, replace ............................................150
Bird droppings .............................................134
Boot lid ............................................................ 87
Brake circuits ...............................................103
Brake fluid, reservoir ........................ 142, 147
Brake servo ...................................................103
Brake system ........................................37, 103
Bulbs, replacing, front ................................152
C
Calibrating compass ..................................... 52
Car wash .......................................................134
CD changer functions ................................176
CD, MD functions ........................................175
Child safety ..................................................... 28
Child safety locks, manual ........................... 89
Child seat ........................................ 20, 30, 31
Child seat and airbag ................................... 28
Child seat and WHIPS ................................ 23
Children in the car, positioning .................. 30
Cigarette lighter ............................................. 40
Cleaning the car ..........................................134
Cleaning the upholstery .............................134
Clutch fluid, reservoir ....................... 142, 147
Cold start ......................................................100
Colour code ..................................................136
Condensation in the fuel filter ..................144
Coolant reservoir .........................................146
Cooling system .............................................. 94
Cruise control ................................................. 45
D
Defroster, A/C ................................................62
Defroster, ECC ...............................................65
Degreasing ................................................... 134
Detachable towbar ..................................... 114
Diesel ................................................................95
Dipstick for engine oil ................................ 142
Direction indicators .......................................43
Dolby Surround Pro Logic II ..................... 167
Door mirrors, outer ........................................53
DSTC ............................................................. 105
E
Economical driving ........................................94
Electric child safety locks .............................89
Electric socket ................................................40
Emergency calls .......................................... 181
Emissions system, indicator symbol ..........36
Empty tank .................................................... 144
Engine preheater, diesel ..............................36
Entertainment ............................................... 164
Equalizer ....................................................... 168
Exhaust emissions ............................100, 198
F
Fan, ECC .........................................................64
Floor mats ........................................................77
Fog lamp, indicator symbol ..........................36
Fog lamps ............................................. 41, 154
201
Index
Frequency updating ................................... 173
Fuel filler flap ...................................................41
Fuel heater .......................................................70
Fuel system .................................................. 144
Fuses ............................................................. 158
G
Gear positions, 5-speed ..............................98
Gear positions, 6-speed ......................98, 99
Gear selector inhibitor ............................... 101
Generator, indicator symbol ........................37
H
Handbrake ...............................................36, 49
Hazard warning flashers ...............................48
Head restraints, WHIPS ..............................23
Headlamp levelling ........................................41
Headlamp washers ........................................46
Headlamps ......................................................41
Heated front seats .........................................66
Heated mirrors ................................................66
Home safe light ..............................................43
I
Immobilizer ...............................................84, 96
Inflatable curtain .............................................22
Inflatable curtains ...........................................27
Information display .........................................39
Infotainment .................................................. 164
202
Installation instructions, child seats ........... 32
Instrument lighting ......................................... 41
Integrated booster cushion. ........................ 31
ISOFIX ............................................................. 31
N
J
Oil and oil filter ............................................ 145
Oil cooler ...................................................... 111
Oil grade, viscosity ..................................... 195
Overheating ....................................................94
Jump starting ................................................109
K
Key .................................................................... 85
Keypad ................................................ 166, 181
Kick-down .....................................................102
L
Light switch .................................................... 43
List of dimensions .......................................120
Load carrier ...................................................117
Load retaining eyelets .................................. 80
Locking, unlocking ........................................ 87
M
Magnetic zones .............................................. 53
Maintenance, rustproofing ........................137
Memory function in the remote control .... 73
Menu selection audio .................................178
Microphone ...................................................181
Motion sensor ................................................ 91
News .............................................................. 170
O
P
Paint, rust onset .......................................... 136
Parking brake ..................................................49
Passenger compartment filter .....................60
PI searching ................................................. 170
Pinch protection .............................................56
Polish and wax ............................................. 135
Position/parking lamps .................................41
Power consumption ......................................94
Power seats ....................................................73
Power steering fluid ................................... 147
Power windows ..............................................50
Pregnant women ............................................15
Programme type .......................................... 172
Punctures ..................................................... 128
R
Radiator ......................................................... 142
Radiator fan .................................................. 142
Radio text ...................................................... 172
Index
Rain sensor .....................................................46
Rape Methyl Ester ...................................... 144
Rear fog lamp .................................................42
Rear windscreen defroster ..........................66
Rearview mirror ..............................................52
Recirculation ...................................................64
Recovery ....................................................... 107
Refuelling .........................................................95
Reverse gear inhibitor, five speed ..............98
RME (Rape Methyl Ester) ......................... 144
S
Seat adjustment .............................................72
Seat belt reminder, indicator symbol .........37
Seat belts ........................................................14
Seat setting .....................................................23
Service key ......................................................85
Service locking ...............................................85
Service program .......................................... 140
Side airbags ....................................................20
SIM card ....................................................... 182
SIPS airbag .....................................................20
Slippery surfaces ...........................................94
Snow chains ................................................ 121
Sound setting .............................................. 167
Spare wheel ................................................. 122
Spin control .................................................. 105
SRS System ....................................................19
SRS, symbol ...................................................37
Stability Control ........................................... 105
Stability system ............................................105
Stains .............................................................134
Start key .......................................................... 96
Station search ..............................................169
STC ................................................................105
STC/DSTC, indicator symbol ..................... 36
Steel rims ......................................................121
Stone chips and scratches .......................136
Studded tyres ...............................................121
Sun screen ...................................................... 56
Sunroof ............................................................ 55
Symbols .........................................................149
T
Telephone menu selection ........................188
Telephone system .......................................181
Telephone, control panel ...........................183
Temperature, ECC ........................................ 66
Temporary spare ..........................................122
Testing the alarm ........................................... 91
Towbar ................................................ 110, 112
Towing ...........................................................107
Towing bracket ............................................110
Towing eye ....................................................107
TP searching ................................................172
Traction Control ...........................................105
Traction control ............................................105
Traffic information ........................................170
Trailer weight ................................................110
Trailer, indicator symbol ............................... 36
Tyre pressure ............................................... 123
Tyres and handling ..................................... 120
Tyres, new .................................................... 120
V
Vanity mirror ....................................................75
Volvo service programme ......................... 140
W
W – Winter .................................................. 102
Warning symbol .............................................35
Warning symbol, SRS ..................................18
Warning triangle ............................................81
Washer fluid, filling ..................................... 146
Washing ........................................................ 134
Wax and polish ............................................ 135
Wear indicators ........................................... 120
Wheel nuts ................................................... 121
Wheels, replacing .............................124, 125
Whiplash ..........................................................23
WHIPS seat ....................................................23
WHIPS, Whiplash Protection System ......23
Windscreen washers ....................................46
Winter tyres .................................................. 120
Wiper blade, replacing .............................. 148
203
Index
204
2004
VOLVO
S40
TP 7011 (English). AT 0347. Printed in Sweden, Elanders Infologistics Väst AB, Mölnlycke 2004
OWNE R'S MANUAL S40
TP 7011
2004

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement