Chauvet | 86 | User manual | Chauvet 86 User manual

LED-PAR83
LEDsplash™ Jr.
USER MANUAL
CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
2008-11-17/09:40
Table of Content
BEFORE YOU BEGIN ........................................................................................................................................................... 3
What is included .................................................................................................................................................................................................................. 3
Unpacking Instructions........................................................................................................................................................................................................ 3
AC Power ............................................................................................................................................................................................................................ 3
Safety Instructions............................................................................................................................................................................................................... 3
INTRODUCTION ................................................................................................................................................................... 4
Features .............................................................................................................................................................................................................................. 4
DMX Channel Summary ..................................................................................................................................................................................................... 4
Product Overview ................................................................................................................................................................................................................ 5
SETUP ................................................................................................................................................................................... 6
Power .................................................................................................................................................................................................................................. 6
Mounting.............................................................................................................................................................................................................................. 6
OPERATING INSTRUCTIONS.............................................................................................................................................. 7
Master/Slave & Stand-Alone Mode..................................................................................................................................................................................... 7
Daisy Chain Connection ..................................................................................................................................................................................................... 7
Built-in Program Options ..................................................................................................................................................................................................... 7
Manual Control Options ...................................................................................................................................................................................................... 8
DMX Control Mode.............................................................................................................................................................................................................. 8
Setting the DMX address .................................................................................................................................................................................................... 8
APPENDIX........................................................................................................................................................................... 10
DMX Primer ....................................................................................................................................................................................................................... 10
Fixture Linking ................................................................................................................................................................................................................... 10
DMX Channel Values ........................................................................................................................................................................................................ 11
Returns Procedure ............................................................................................................................................................................................................ 11
Claims ............................................................................................................................................................................................................................... 11
DMX Dipswitch Quick Reference Chart ............................................................................................................................................................................ 12
Technical Specifications ................................................................................................................................................................................................... 13
Technical Support ............................................................................................................................................................................................................. 13
LED-PAR83 User Manual
2
2008-11-17 9:40:00 AM
BEFORE YOU BEGIN
What is included
¾
¾
¾
¾
1 x LED-PAR83 LEDsplash™ JR
1 x Power cable (1 m) and 1 x Linking cable (1.5 m)
Warranty Card
Users Manual
Unpacking Instructions
Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular product, see the label affixed to the back plate
of the product or refer to the product’s specifications chart. A product’s listed current rating is its
average current draw under normal conditions. All fixtures must be powered directly off a switched
circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit,
AC Voltage Switch Example
even if the rheostat or dimmer channel is used solely for a 0% to 100%
switch. Before applying power, check that the source voltage matches the
product’s requirement. Check the product or device carefully to make sure
that if a voltage selection switch exists that it is set to the correct line
voltage you will use.
Warning!
If applicable, verify that the power select switch on your unit matches the line
voltage applied. All fixtures must be connected to circuits with a suitable Earth
Ground.
Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance?
•
•
•
•
•
•
•
Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive
this instruction booklet.
Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to
rain or moisture. Make sure there are no flammable
materials close to the unit while operating.
The unit must be installed in a location with adequate
ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•
Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same
lamp source.
Caution!
Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying
handles.
Maximum ambient temperature is Ta: 40°. Do not operate
fixture at temperatures higher than this.
•
In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.
•
•
Don’t connect the device to a dimmer pack.
Make sure power cord is never crimped or damaged.
•
Never disconnect power cord by pulling or tugging on the
cord.
Avoid direct eye exposure to lamp while it is on.
•
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.
LED-PAR83 User Manual
3
2008-11-17 9:40:00 AM
INTRODUCTION
Features
CONTROL FEATURES
•
5-channel DMX-512 LED wash light
•
Blackout/static/dimmer/strobe
•
Static colors and RGB color mixing with or without DMX controller
FEATURES
•
Additional power output: max 50 units @ 120V (see manual for details) (115V models only)
•
Linkable power with other LEDrain™ and LEDsplash™ units (115V models only)
•
Built-in automated programs via master/slave
OPTIONS
• Programmable: Any universal DMX-512 controller
DMX Channel Summary
CHANNEL
INTENSITY CONTROL OF
1
Reserved
2
Blackout/Strobe/Dimmer
Red
Green & Blue
3
Red
Red
Green & Blue
4
Green
5
Blue
Red
Green & Blue
Red
Green & Blue
Red
LED-PAR83 User Manual
4
2008-11-17 9:40:00 AM
Product Overview
DMX Connectors
switches:
DMX dip
dipswitches:
nel addressing
DMX chan
channel
Power link
Fuse
Power c
connection
onnection
AC Voltage Switch
Hanging yoke
Red
Green & Blue
Red
Green & Blue
Red
Green & Blue
Red
Green & Blue
Red
LED-PAR83 User Manual
5
2008-11-17 9:40:00 AM
SETUP
Power
Warning!
Verify that the power indicator label on your unit matches the line voltage applied.
All fixtures must be connected to circuits with a suitable Earth Ground.
• To determine the power requirements for a particular fixture, see the label affixed to the back plate
of the fixture or refer to the fixture’s specifications chart.
• A fixture’s listed current rating is its average current draw under normal conditions.
• All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%
to 100% switch.
• Before applying power to a fixture, check that the source voltage matches the fixture’s
requirement.
• All fixtures must be connected to circuits with a suitable Earth Ground.
Pow er C able C onf igur at io n
CABLE
PIN
INTERNATIONAL
BROWN
Live
L
BLUE
Neutral
N
YELLOW/GREEN
Earth
EG (Ground)
Mounting
O r ie ntat ion
Optional Hanging Clamp
This fixture can be mounted on a truss using a clamp in any
position.
R ig g in g
The fixture includes a mounting yoke to which 1 rigging clamp can be bolted.
1. Align the clamp screw with the center hole on the yoke and tighten.
2. Verify the structure can hold 10 times the weight of all to-be installed fixtures.
3. Adjust the angle on the yoke arm as necessary.
LED-PAR83 User Manual
6
2008-11-17 9:40:00 AM
OPERATING INSTRUCTIONS
The LEDsplash™ Jr. is a DMX-512 controllable, full RGB color mix par can made up of highly
efficient and super bright LED’s. There are three color groups (Red, Green and Blue) whose intensity
can be controlled individually allowing the creation of an unlimited range of colors.
The LEDsplash™ Jr. can operate in Stand-Alone, Master/Slave and via DMX-512 control utilizing 4
channels.
Master/Slave & Stand-Alone Mode
The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In
this mode, the first unit in the daisy chain will automatically command all other units following.
1. Connect all LEDsplash™ Jr. units in a daisy
IN
DMX512
OUT
chain fashion as described in the section
ON
ON
9
10
8
7
6
5
4
3
2
1
9
8
7
6
5
10
4
3
2
1
following.
TM
COLORsplash Jr.
2. Master Unit: Set dipswitch # 9 to ON and #10
FUSE
Master Setting
POWER
OUT AC
POWER
IN AC
to OFF.
3. Slaves: Set dipswitch # 10 to the ON position
and all others to the OFF position.
IN
DMX512
OUT
ON
9
10
8
7
6
FUSE
5
Slave Setting
COLORsplash Jr.
fixtures to run as master units.
4
TM
3
9
8
7
6
5
4
3
2
1
stand-alone mode by simply setting all
2
ON
10
1
4. You can also run the fixtures in an automatic
POWER
OUT AC
POWER
IN AC
D a i s y C h a in C on ne ct i o n
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Optional DMX Controller
IN
DMX512 OUT
IN
DMX512 OUT
ON
DMX512 OUT
9
8
7
6
5
4
COLORsplash Jr.
POWER
OUT AC
POWER
IN AC
3
TM
COLORsplash Jr.
FUSE
2
1
TM
10
10
9
8
7
6
5
4
POWER
OUT AC
3
POWER
IN AC
2
FUSE
DMX512 OUT
ON
1
9
8
7
6
5
4
3
2
1
TM
COLORsplash Jr.
POWER
OUT AC
IN
ON
10
9
8
7
6
5
4
3
2
1
10
POWER
IN AC
IN
ON
TM
COLORsplash Jr.
FUSE
Continue
Use 3-pin XLR DMX cable
FUSE
POWER
OUT AC
POWER
IN AC
AC Line
Continue
Use AC linking cable for convenience. As many as 50 par cans
can be powered from one AC daisy chain connection.
B u i l t - in P ro gr a m Op t i o ns
Dipswitches 1 ~ 8
(programs)
There are 8 Individual programs that can be
accessed by turning ON dipswitches 1 through 8
individually.
ON
9
10
8
7
6
5
4
3
7
2
1
LED-PAR83 User Manual
2008-11-17 9:40:00 AM
M an ua l C on t r o l Opt io ns
With all dipswitches set to the OFF position,
Manual Intensity Control
RGB Mix
dipswitches 1 through 8 will control 3 levels of
intensity for red and green LED’s and 2
RED
levels of intensity for blue LED’s.
This allows you to statically set
a color of preference without
the use of a controller. By
setting different intensities for
ON
10
10
9
10
8
9
8
7
9
7
6
5
4
3
2
1
all 3 led colors you can
compose a color of your
choice.
GREEN
ON
6
5
4
3
2
1
BLUE
ON
8
7
6
5
4
3
2
1
DMX Control Mode
Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to
customizing or creating a show. In this mode you will be able to control each individual trait of the
fixture and each fixture independently. The LEDsplash™ Jr. uses 4 channels of control.
1. Enable DMX control by setting dipswitch # 10 to the ON position. Use dipswitches 1 through 9 to
address each fixture accordingly.
Set ting the D M X ad dr es s
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start
address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data
on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels
of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,
102, 103, 104, 105 and 106. Choose start addresses so that the channels used do not overlap and
notate the start address selected for future reference.
If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that
will help you understand its use.
LED-PAR83 User Manual
8
2008-11-17 9:40:00 AM
Set the start address using the group of DIP switches located usually on bottom of the fixture. Each
dip switch has an associated value. Adding the value of each switch in the ON position will provide
the start address. Determining which switches to toggle ON given a specific start address can be
accomplished in the following manner. By subtracting the largest switch value possible from the
selected start address until zero is achieved.
EXAMPLE STARTING ADDRESS
Address 10
ON
9
128
256
8
9
64
128
256
10 OPTION
8
7
8
16
6
5
4
64
16
4
2
32
5
8
3
1
7
4
4
2
6
3
1
= 10
2
=2
Total
1
Pin # 2
2
=8
1
Pin # 4
Address 24
ON
Pin # 4
=8
Total
= 24
Resolving address using
simple math.
Address 233
LED-PAR83 User Manual
233 – (128) = 105, Turn ON Dip # 8
105 – (64) = 41, Turn ON Dip # 7
41 – (32) = 9, Turn ON Dip # 6
9 – (8) = 1, Turn ON Dip # 4
1 – (1) = 0, Turn ON Dip # 1
You will most likely use the first
available number which maybe
number 1. This number was
selected for example purposes.
9
10 OPTION
= 16
32
Pin # 5
DIP SWITCH
(DMX VALUE)
1
2
3
4
5
6
7
8
9
10
1
2
4
8
16
32
64
128
256
2008-11-17 9:40:00 AM
APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
F i xtu re L in k in g
DMX connector configuration
1
3
2
COMMON
INPUT
1
3
1
3
DMX +
2
2
DMX -
Note!
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
OUTPUT
Termination reduces signal errors and to
avoid signal transmission problems and
interference, it is always advisable to
connect a DMX signal terminator.
If you use a controller with a 5 pin DMX output connector, you will need to use a 5
pin to 3 pin adapter. CHAUVET Model No: DMX5M.
The chart below details a proper cable conversion:
3 PIN TO 5 PIN CONVERSION CHART
LED-PAR83 User Manual
Conductor
3 Pin Female (output)
5 Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - )signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Do not use
Do not use
Do not use
Do not use
10
2008-11-17 9:40:00 AM
DMX Channel Values
DEFAULT
VALUE
FUNCTION
1
000 Ù 255
Reserved
2
000 Ù 001
002 Ù 127
128 Ù 255
Shutter/Strobe/Dimmer
Blackout
Strobe: Slow > Fast
Intensity: 0% > 100%
3
000 Ù 255
Red
0 > 100%
4
000 Ù 255
Green
0 > 100%
5
000 Ù 255
Blue
0 > 100%
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).
Products returned without an RMA # will be refused. Call CHAUVET and request RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from
inadequate packaging is the customer’s responsibility. CHAUVET reserves the right to use its own
discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is
always a safe method to use.
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
LED-PAR83 User Manual
11
2008-11-17 9:40:00 AM
DMX Dipswitch Quick Reference Chart
DMX Address Quick Reference Chart
Dip Switch Position
0
0
0
1
1
1
1
1
1
1
1
0=OFF
#8
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
1=ON
#7
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
X=OFF or ON
#6
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
DMX DIP SWITCH SET #9
0
0
0
0
0
#1
#2
#3
#4
#5
0
0
0
0
0
32
64
96
128
160
192
224
256
288
320
352
384
416
448
480
1
0
0
0
0
1
33
65
97
129
161
193
225
257
289
321
353
385
417
449
481
0
1
0
0
0
2
34
66
98
130
162
194
226
258
290
322
354
386
418
450
482
1
1
0
0
0
3
35
67
99
131
163
195
227
259
291
323
355
387
419
451
483
0
0
1
0
0
4
36
68
100
132
164
196
228
260
292
324
356
388
420
452
484
1
0
1
0
0
5
37
69
101
133
165
197
229
261
293
325
357
389
421
453
485
0
1
1
0
0
6
38
70
102
134
166
198
230
262
294
326
358
390
422
454
486
1
1
1
0
0
7
39
71
103
135
167
199
231
263
295
327
359
391
423
455
487
0
0
0
1
0
8
40
72
104
136
168
200
232
264
296
328
360
392
424
456
488
1
0
0
1
0
9
41
73
105
137
169
201
233
265
297
329
361
393
425
457
489
0
1
0
1
0
10
42
74
106
138
170
202
234
266
298
330
362
394
426
458
490
1
1
0
1
0
11
43
75
107
139
171
203
235
267
299
331
363
395
427
459
491
0
0
1
1
0
12
44
76
108
140
172
204
236
268
300
332
364
396
428
460
492
1
0
1
1
0
13
45
77
109
141
173
205
237
269
301
333
365
397
429
461
493
0
1
1
1
0
14
46
78
110
142
174
206
238
270
302
334
366
398
430
462
494
1
1
1
1
0
15
47
79
111
143
175
207
239
271
303
335
367
399
431
463
495
0
0
0
0
1
16
48
80
112
144
176
208
240
272
304
336
368
400
432
464
496
1
0
0
0
1
17
49
81
113
145
177
209
241
273
305
337
369
401
433
465
497
0
1
0
0
1
18
50
82
114
146
178
210
242
274
306
338
370
402
434
466
498
1
1
0
0
1
19
51
83
115
147
179
211
243
275
307
339
371
403
435
467
499
0
0
1
0
1
20
52
84
116
148
180
212
244
276
308
340
372
404
436
468
500
1
0
1
0
1
21
53
85
117
149
181
213
245
277
309
341
373
405
437
469
501
0
1
1
0
1
22
54
86
118
150
182
214
246
278
310
342
374
406
438
470
502
1
1
1
0
1
23
55
87
119
151
183
215
247
279
311
343
375
407
439
471
503
0
0
0
1
1
24
56
88
120
152
184
216
248
280
312
344
376
408
440
472
504
1
0
0
1
1
25
57
89
121
153
185
217
249
281
313
345
377
409
441
473
505
0
1
0
1
1
26
58
90
122
154
186
218
250
282
314
346
378
410
442
474
506
1
1
0
1
1
27
59
91
123
155
187
219
251
283
315
347
379
411
443
475
507
0
0
1
1
1
28
60
92
124
156
188
220
252
284
316
348
380
412
444
476
508
1
0
1
1
1
29
61
93
125
157
189
221
253
285
317
349
381
413
445
477
509
0
1
1
1
1
30
62
94
126
158
190
222
254
286
318
350
382
414
446
478
510
1
1
1
1
1
31
63
95
127
159
191
223
255
287
319
351
383
415
447
479
511
Dip Switch Position
LED-PAR83 User Manual
DMX Address
12
2008-11-17 9:40:00 AM
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................... 4.92 in (125 mm)
Width ............................................................................................................................ 4.92 in (125 mm)
Height ........................................................................................................................... 7.87 in (200 mm)
Weight ............................................................................................................................ 2.43 lbs (1.1 kg)
POWER
Switch-selectable power setting .................................................................... 115V 60 Hz or 230V 50 Hz
AC input ................................................................................................................... Power cord attached
European version .................................................................................................................. 240V 50 Hz
Power output ....................................................................................................................... 50 units max
FUSE
Main ............................................................................................................... 20mm Glass 1A Fast Blow
LIGHT SOURCE
LED.............................................................................. 86 (44 red, 21 green, 21 blue) LEDs 100,000hrs
PHOTO OPTIC
Luminance at 1 meter ................................................................................................................. (538 lux)
Beam Angle ........................................................................................................................................ 17°
Field Angle.......................................................................................................................................... 52°
CONTROL & PROGRAMMING
Data input ................................................................................................ locking 3-pin XLR male socket
Data output ........................................................................................... locking 3-pin XLR female socket
Data pin configuration .............................................................................. pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................................ DMX-512 USITT
DMX Channels ....................................................................................................................................... 5
ORDERING INFORMATION
LEDsplash™ Jr..................................................................................................................... LED-PAR83
Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): tech@chauvetlighting.com
Telephone: (954) 929-1115 - (Press 4)
Fax: (954) 929-5560 - (Attention: Service)
Website: http://www.chauvetlighting.com
LED-PAR83 User Manual
13
2008-11-17 9:40:00 AM
Download PDF