Pro-face | PL-6930-T42 | Hardware manual | Pro-face PL-6930-T42 Hardware manual

Windows XP Embedded
Reference Manual
CF card capacity : 1GB
File system
: NTFS
Supported language : Japanese/English
version
Multi-language version
Preface
Thank you for purchasing Pro-face’s Windows XP Embedded (Hereafter referred to as the “XPE”).
Before using the XPE, be sure to read this manual thoroughly to familiarize yourself with the XPE’s operation procedures
and functions.
Supported Model List
Series
PS-3450A
PS-3451A
PS-3000B
PS-3001B
PS-3650A
PS-3651A
PS-3710A
PS-3711A
PL-6930T
PL-6931T
PL-7930T
PL-7931T
Unit model
Unit revision Supported CF card model
PS345XA-XPE1G-JE-BLD
PS345XA-XPE1G-ML-BLD
PS345XA-XPE1G-JE-BLD
PS3000-BA
No Rev.
PS3001-BD
or later
PS345XA-XPE1G-ML-BLD
PS365*A-T41
PS365XA-XPE1G-J1-BLD
No Rev.
PS365*A-T41-24V or later
PS365XA-XPE1G-M1-BLD
PS3710A-T41
PS3710A-XPE1G-JE-BLD
No Rev.
PS3710A-T41-24V or later
PS3710A-XPE1G-ML-BLD
PS3711A-T41
PS3711A-XPE1G-JE-BLD
No Rev.
PS3711A-T41-24V or later
PS3711A-XPE1G-ML-BLD
PS3450A-T41
No Rev.
PS345*A-T41-24V or later
PL*93*-T41
PL*93*-T42-CM
PL*93*-T42-PM
No Rev.
or later
Volume label
345XAXPEJE1 or later
345XAXPEM1 or later
345XAXPEJE2 or later
345XAXPEM2 or later
365XAXPEJ3 or later
365XAXPEM3 or later
3710AXPEJE1 or later
3710AXPEM1 or later
3711AXPEJE1 or later
3711AXPEM1 or later
PLX930-XPE1G-J1-BLD
PLX930XPEJ4 or later
PLX930-XPE1G-M1-BLD
PLX930XPEM4or later
*
The last digit of the volume label indicates a version number which corresponds to the software revision.
*
The newest manual, Driver and Utility can be downloaded from the Digital Electronics Corporation’s homepage.
Also often questions and helpful informations are uploaded as Q&A to Digital Electronics Corporation’s homepage.
Please refer them to the purpose of usage.
http://www.pro-face.com/otasuke/
NOTE
1.
It is forbidden to copy the contents of this manual in whole, or in part, without the permission of the Digital Electronics Corporation.
2.
The information in this manual is subject to change without notice.
3.
This manual was written with care; however, if you should find any error or omissions, please contact Digital
Electronics Corporation and inform them of your findings.
4.
Regardless of the above clause, Digital Electronics Corporation shall not be held responsible for any damages or
third-party claims for damages or losses resulting from the use of this product.
© Copyright 2007 Digital Electronics Corporation. All rights reserved.
Windows is a registered trademark of Microsoft Corporation.
All other trademarks and registered trademarks are property of their respective owners.
1
TRADEMARK RIGHTS
The company names and product names used in this manual are the trade names, trademarks (including registered trademarks), and service marks of their respective companies. This product omits individual descriptions of each of these
rights.
Trademark / Tradename
Right Holder
Microsoft, Windows
Microsoft, U.S.
Pro-face
Digital Electronics Corporation
(in Japan and other countries)
Adobe
Adobe Systems Incorporated
The following terms differ from the abovementioned trade names and trademarks.
Term used in this manual
2
Formal Trademark or Tradename
Windows XP
Microsoft® Windows® XP operating system
Adobe Reader
Adobe® Reader®
How to use this manual
This manual makes special mention of XPE's feature and setup method.
For the hardware-related instructions for use, setup methods, and so on, refer to the Instruction guide, which is contained
in this package or IPC (Industrial Personal Computer) Series Hardware Manual.
For the software-related instructions, setup method of software, and so on, refer to the IPC (Industrial Personal Computer)
Series Reference Manual.
Information Symbols
This manual uses the following icons:
Indicates a warning or a product limitation. Be sure to follow the instructions given
with this icon to insure the safe operation of the XPE.
Contains additional or useful information.
*
Indicates terms or items that require further explanation. See the footnote on that
page.
(1) (2)
Indicates steps used to accomplish a given task.
Be sure to follow these steps in the order they are written.
XPE
Refers collectively to the Windows XP Embedded.
)
Indicates pages containing related information.
3
Package Contents
The following items exclusively for XPE are included in the package. Before using the XPE, please confirm that all items
listed here are present.
End User LicenseAgreement (EULA)(1)
• This unit has been carefully packed, with special attention to quality. However, should you find
anything damaged or missing, please contact your local XPE distributor immediately.
• The newest manual, Driver and Utility can be downloaded from the Digital Electronics
Corporation's homepage.
http://www.pro-face.com/otasuke/
4
Table of Contents
Preface ...................................................................................................................... 1
Supported Model List ................................................................................................ 1
TRADEMARK RIGHTS ............................................................................................. 2
How to use this manual ............................................................................................. 3
Information Symbols.................................................................................................. 3
Package Contents ..................................................................................................... 4
Table of Contents ...................................................................................................... 5
Chapter1 Windows XP Embedded
1 Feature .............................................................................................................. 1-2
2 List of primary application programs ................................................................. 1-4
3 Function List of Control Panel in the XPE ......................................................... 1-5
4 Setting the Write Filter (Write Protection).......................................................... 1-6
4.1 Write Filter Settings Procedure ..............................................................................1-7
4.2 Acress operation to the CF card of the Write filter .................................................1-8
5 Copy the same setting environment to multiple panel computers (Copying the CF
card) .................................................................................................................... 1-10
5.1 Copying the CF card procedure...........................................................................1-10
6 Solve the memory leak caused by the Write filter ........................................... 1-12
6.1 RAM Disk Settings Procedure .............................................................................1-12
7 Displaying keyboard on the screen ................................................................. 1-15
7.1 Changing input font size procedure .....................................................................1-15
8 Using Touch Panel Operations ....................................................................... 1-17
9 Backlight Brightness........................................................................................ 1-18
10 Notes on turning off the power ...................................................................... 1-19
11 Backup/Recovery of the CF Card.................................................................. 1-20
12 Restrictions.................................................................................................... 1-21
Chapter2 Troubleshooting
1 Problems and countermeasures ....................................................................... 2-2
Chapter Appendices
1 [IN-fINITY soft KeyClick32] Agreement ............................................................. A-2
2 [DMC Corporation Mouse Emulation Software] SLA......................................... A-3
5
6
1
Windows XP Embedded
1
Feature.......................................................................................................................... 1-2
2
List of primary application programs ............................................................................. 1-4
3
Function List of Control Panel in the XPE..................................................................... 1-5
4
Setting the Write Filter (Write Protection)...................................................................... 1-6
5
Copy the same setting environment to multiple panel computers (Copying the CF card) ..
6
Solve the memory leak caused by the Write filter ....................................................... 1-12
7
Displaying keyboard on the screen............................................................................. 1-15
8
Using Touch Panel Operations ................................................................................... 1-17
9
Backlight Brightness ................................................................................................... 1-18
10
Notes when turning off the power ............................................................................... 1-19
11
Backup/Recovery of the CF Card ............................................................................... 1-20
12
Restrictions .................................................................................................................1-21
1-10
1-1
Windows XP Embedded Reference Manual
1
Feature
The XPE is the component version of the Windows XP operating system and is the operating system which
has the discriminative function about an embedded device such as the Write Filter.
• The CF card must be connected to the primary master (Disk 0).
• Back up the data after installing the required application programs. Data cannot be
recovered without backup data.
) "11 Backup/Recovery of the CF Card" (Page 1-20)
• The newest manual, Driver and Utility can be downloaded from the Digital Electronics
Corporation's homepage.
http://www.pro-face.com/otasuke/
The XPE made by Pro-face has the following features.
„ Write Filter Function (The function to protect the CF card from writing)
This unit has the Write Filter function to prevent writing into CF card. Be sure the Write Filter is enabled to
decrease the number of times of writing to CF card. And if the Write Filter function is effective, the operation
for shutdown is unnecessary.
)"4 Setting the Write Filter (Write Protection)" (Page 1-6)
„ Supporting Multi-language Function
Japanese XPE supports two languages: English and Japanese (Default setting)
Multi-language XPE supports eight languages: English (Default setting), Spanish, French, German, Italian,
Russian, Chinese and Taiwanese.
„ Using with an HDD
Using an HDD with the CF card increases data capacity and enables the use of large software applications.
• PS-3450A/PS-3451A, PS-3650A/PS-3651A and PS-3710A/PS-3711A Series are not HDDcompatible.
• Connected HDD has no Write Filter function.
1-2
Chapter 1 Windows XP Embedded
„ Backlight Screen Saver Function
It’s the screen saver function that turns ON/OFF the backlight and can extend the backlight’s lifetime.
„ Installed System Monitor
It enables Error Monitor of the system.
For details, refer to IPC Series Reference Manual.
„ Supporting Touch Panel Driver (UPDD)
The input operation like a mouse is possible with the touch operation.
)"8 Using Touch Panel Operations" (Page 1-17)
„ Installed KeyClick
It displays the keyboard on a screen and enables the key input from the touch panel.
)"7 Displaying keyboard on the screen" (Page 1-15)
„ RAM Disk
Use the RAM Disk to solve the memory leak caused by the Write filter.
RAM Disk will enable to write the data directly into the memory area.
Therefore, the area of the RAM Disk can be used again and again whether the Write filter is enabled or not.
)"6 Solve the memory leak caused by the Write filter" (Page 1-12)
• When installing applications, be aware of CF card’s available area as shown below.
<Before shipment>
Japanese/English Version / Japanese Version About 650MB
Multilanguage Version
About 530MB
1-3
Windows XP Embedded Reference Manual
2
List of primary application programs
The main installed applications before shipment are shown in the table below.
applications
Internet Explorer 6
Japanese IME
*1
Details
Web Browser (Microsoft.Corp.)
Conversion software for Japanese input.
Control Panel
Customize a computer. Add new hardwares, add / remove programs,
chang the screen display and start various operations.
The System Monitor’s settings screen can also be displayed.
Accessary
Microsoft’s Notepad, Paint, On-Screen Keyboard, Command Prompt,
and Hyper Terminal are installed.
Backlight Brightness
Adjusts brightness of a screen.
Keyclick
Displays the keyboard on a screen and operates the key input.
Supports Japanese and English only.
UPDD
Operates the touch panel.
EWF Setting Tool *2
Sets the Write Filter function.
System Monitor
Monitors errors of the system.
*1
Multi-language XPE does not have this function.
*2
Changing the setting requires the administrator's authority.
• Often questions and helpful informations are uploaded as Q&A to Digital Electronics Corporation’s homepage. Please refer them to the purpose of usage.
http://www.pro-face.com/otasuke/
1-4
Chapter 1 Windows XP Embedded
3
Function List of Control Panel in the XPE
The function and the setting of the Control Panel in the XPE are as below.
Icons
complement
(useful range etc.)
Details
) "9 Backlight Brightness" (Page 1-18)
The backlight can be set to any of 4
levels of brightness.
The brightness is set to the
maximum in the factory setting.
Internet Option
Configure your Internet display and
connection settings.
In the factory setting, cache size is
set to 1MB and the history
preservation day is set to zero and
the cache file storage folder is
changed to Z:\(RAM Disk).
Folder option
Customize the display of files and folders,
change file associations, and make
network files available offline.
The offline use of network files is
disabled in the factory setting.
Printer and FAX
Shows installed printers and helps you add
new ones.
FAX is not compatible.
Add/Remove
programs
Install or remove programs and Windows
components.
Add / Remove Windows component
and Windows Update cannot be
used.
Internet
Information
Service
Manages Internet Information Service, the
web server for Internet and intranet web
sites.
The Internet Information Service is
disabled in the factory setting.
BackLight
Brightness
Change Backlight Brightness settings.
• Before changing settings, disable the Write Filter. When the Write Filter is enabled, the change is
not reflected.
Enabling the Write Filter after changing the setting is recommended.
) "4.1 Write Filter Settings Procedure" (Page 1-7)
1-5
Windows XP Embedded Reference Manual
4
Setting the Write Filter (Write Protection)
XPE has the Write Filter (The function to avoid writing into HDD or Flash Memory).
When the Write Filter is effective, it prevents writing into CF card.
The Write Filter protects the CF card from being damaged or failing.
• When data is written in the devices (except CF card) that are not protected by the Write
Filter, turning off the power may cause damage of the data.
) "10 Notes on turning off the power" (Page 1-19)
• When making settings, adding a driver, or changing registries, be sure to disable the
Write Filter. If the Write Filter is enabled, the settings regarding the OS will be all canceled when OS restarts. When changing the setting, be sure to disable the Write Filter
setting.
Enabling the Write Filter after changing the setting is recommended.
1-6
Chapter 1 Windows XP Embedded
4.1 Write Filter Settings Procedure
When setting the Write Filter, use “EFW Setting Tool”. This tool has the following function. The Write Filter
is enabled in the factory setting.
•
The Write Filter is enabled (Protect ON).
•
The Write Filter is disabled (Protect OFF).
•
Change of security ID.
• Changing the setting of the Write Filter requires the administrator’s authority.
• Changing the security ID is not available when the Write Filter is enabled.
• Refer to the following section for the security ID.
) "5 Copy the same setting environment to multiple panel computers (Copying the CF
card)" (Page 1-10)
(1)
Select [Designate file name and run] from the [Start] menu and start the following executable file.
C:\Proface\EWFSettingTool\EWFSettingTool.exe
(2)
Confirm current setting on the display screen.
Not available
when the Write
Filter is enabled.
Checking
here will add
the EWF
Setting Tool
icon to the
task tray.
(3)
Choose the setting.
(4)
Clicking [OK] displays the dialogbox “Do you want to change the Write Filter settings?” to confirm the
setting change. Click [OK] to enable the setting.
* Restart and the contents of change becomes effective.
1-7
Windows XP Embedded Reference Manual
4.2 Acress operation to the CF card of the Write filter
„ When the Write Filter is enabled
•
Read: Direct access to CF card
•
Write: Access to the memory
Application
Read
Write
Write
Write Filter
Enable
Memory
Read
Read
CF card
• When the added or changed data is on the memory, the data on the memory precedes.
• The memory leak will be caused, when accessing to the Write Filter enabled CF card.
To solve the memory leak caused by the Write filter, refer to the following below.
) "6 Solve the memory leak caused by the Write filter" (Page 1-12)
„ When the Write Filter is disabled
•
Read: Direct access to CF card
•
Write: Direct access to CF card
Application
Read
Write
Write Filter
Disable
Read
Memory
Write
CF card
• Turning off the power when writing into a CF card may result in damaged or lost data. The Write
Filter must be enabled.
1-8
Chapter 1 Windows XP Embedded
„ Write Filter-related important notes
•
If the Write Filter is enabled, when writing to the CF card, data is written on the memory. When deleting
the data on the memory, some data may remain. However, it will be deleted after rebooting.
•
Even if the CF card has an avaiable area, when the memory has no avaiable area, writing data causes the
disk’s insufficient available area error. And when the memory has a avaiable area and the CF card has no
avaiable area, the Writing Error occurs and data cannot be written. When writing data, be sure to check
avaiable areas of the CF card and the memory.
Ex.) With the Write Filter enabled, when writing 10-MB data,
10 MB data
Used
Area
Used
Area
Used
Area
10MB
Avaiable
Area
CF card
Avaiable
Area
Avaiable
Area
Memory
Before
writing
Memory
After
writing
<Conditions to write 10-MB data>
•
The appearing avaiable area in the CF card is 10 MB or more
•
The memory’s available area: 10MB + memory’s available area necessary for OS to operate properly.
<State after 10-MB data is written>
•
The appearing avaiable area in the CF card decreases by 10 MB.
•
The avaiable area in the memory decreases by 10 MB.
<State after 10-MB data is deleted>
•
•
The appearing avaiable area in the CF card returns to the state before 10-MB data is written.
•
The avaiable area in the memory does not change from the state when data is written.
Writing large amounts of data will decrease the available memory. Therefore, during work, it’s necessary to
refrain from writing into the CF card as much as possible.
In order to solve this problem, RAM Disk is installed in XPE made by Pro-face.
In the RAM Disk, the area for the specified size can be used as a volatile disk area. Therefore, that area can be
used again and again when writing directly into the memory area whether the Write Filter is enabled or not.
For details and settings of the RAM Disk, refer to the following section.
)"6 Solve the memory leak caused by the Write filter" (Page 1-12)
1-9
Windows XP Embedded Reference Manual
5
Copy the same setting environment to multiple panel computers
(Copying the CF card)
When copying the same setting environment of the CF card to multiple panel computers , use the following
procedure to copy the CF card.
• By not copying the CF card through the following procedure, a CF card with the same security
ID will be created. A security ID is a unique ID assigned to each panel computer. Computers that
have the same security ID will be recognized as the same computer on the Microsoft Network.
5.1 Copying the CF card procedure
(1)
Disable the Write Filter.
When the Write Filter is enable, the security ID cannot be changed.
)
"4.1 Write Filter Settings Procedure" (Page 1-7)
(2)
Start “EWFSettingTool. exe” and select “Change Security ID” and click [OK].
(Executable file is “C:\Proface\EWFSettingTool\EWFSettingTool.exe”)
.
• Changing the setting requires the administrator's authority.
(3)
1-10
The following dialog box will appear.
Chapter 1 Windows XP Embedded
(4)
Click [OK] and the unit is rebooted automatically.
(5)
BIOS is displayed. While BIOS is displayed, press [F2]key.
Turn off the power supply after BIOS setup screen is displayed and copy the CF card.
(6)
Reboot by using the CF card which you have copied. The security ID will be changed during the first
reboot.
• It may take a long time to boot but since changing the security ID, do not turn off the
power supply.
(7)
After the security ID is changed, the XPE is restarted automatically.
• After restart, Write Filter becomes effective and it’s not necessary to set it again.
• When the security ID is changed, the MACHINE_NAME is changed and therefore the Event
Error occurs.
There are no affects for this error.
1-11
Windows XP Embedded Reference Manual
6
Solve the memory leak caused by the Write filter
Use the RAM Disk to solve the memory leak caused by the Write filter.
RAM Disk will enable to write the data directly into the memory area.
Therefore, the area of the RAM Disk can be used again and again whether the Write filter is enabled or not.
Refer to the following below for the memory leak caused by the Write filter.
)"4.2 Acress operation to the CF card of the Write filter" (Page 1-8)
If the RAM Disk is used as a data storage area such as for Internet Explorer’s cache, it is possible to get the
system to operate without changing the available memory volume for a long time.
Logging data such as users’ applications is one of the data types that can use the RAM Disk effectively.
<In the factory settings>
Drive Letter: Z
Size: 4MB
• Do not change the Drive Letter setting.
• Data can be written in the RAM Disk whether the Write Filter is enabled or not. However, this
data will be lost when the power is turned off.
• Even using the RAM Disk, the memory leek will not be solved completely.
6.1 RAM Disk Settings Procedure
Follow the following procedure to change the RAM disk area.
• Before setting the Ram Disk, disable the Write Filter. When the Write Filter is enabled, the
change is not reflected.
Enabling the Write Filter after changing the setting is recommended.
) "4.1 Write Filter Settings Procedure" (Page 1-7)
(1)
1-12
Start the system in the control panel.
Chapter 1 Windows XP Embedded
(2)
Select the [Hardware] tab and then [Device Manager].
(3)
The following dialog box will appear. Click the “ +” mark on the left from the [RAM Disk] and doubleclick [Ram disk[QSoft]].
1-13
Windows XP Embedded Reference Manual
(4)
The following dialog box will appear. Select the [Ram Disk Properties] tab.
(5)
Set a RAM Disk area in [Disk Size].
• The maximum value of the RAM Disk area is 67108864. When the value over the maximum value is set, an error occurs.
• Do not change the Drive Letter setting.
(6)
1-14
Restart the unit.
Chapter 1 Windows XP Embedded
7
Displaying keyboard on the screen
The KeyClick32 software keyboard made by IN-fINITY soft can be used. Please surely read the License
agreement on the appendix before using it.
)"1 [IN-fINITY soft KeyClick32] Agreement" (Page A-2)
When changing font size, set the setting referring the following diagram.
• Only Japanese and English are supported.
When operating the key input from the touch panel in the language except the above mentioned,
use Microsoft’s Screen Keyboard.
• It cannot be used for password input when starting this unit.
• It cannot be used for command prompt.
7.1 Changing input font size procedure
• Before setting KeyClick, disable the Write Filter. When the Write Filter is enabled, the change is
not reflected.
Enabling the Write Filter after changing the setting is recommended.
) "4.1 Write Filter Settings Procedure" (Page 1-7)
(1)
When using Japanese/English version, start with [Start]-->[All program]-->[KeyClick_J] (Japanese version) or [KeyClick_E] (English version) (Executable file is C:\Proface\KeyClick_J\KeyClick.exe or
C:\Proface\KeyClick_E\KeyClick.exe) When using Multilanguage version, start with [Start]-->[All
program]-->[KeyClick]. (Executable file is C:\Proface\KeyClick\KeyClick.exe
(2)
When changing font size, set the setting referring the following diagram.
• Changing the settings of the KeyClick requires the power user’s or higher authority.
(1) Click here and display dialog for changing font size.
(2) Click PW and end KeyClick. Restart KeyClick and
1-15
Windows XP Embedded Reference Manual
Screen for changing font size.
1-16
Chapter 1 Windows XP Embedded
8
Using Touch Panel Operations
The touch panel driver by DMC Co., Ltd. can be used to enable mouse emulation. Before using, be sure to
read the license arrangement on the appendix.
)"2 [DMC Corporation Mouse Emulation Software] SLA" (Page A-3)
„ Correction procedure for touch point
(1)
Start as the next. [Start]-->[All program]-->[UPDD] and [Calibration].
(Executable file is C:\Program Files\UPDD\TBCALIB.exe)
(2)
Touch the arrow on the screen. Pressing [OK] on the [Confirmation after calibration] dialog box completes the correction.
1-17
Windows XP Embedded Reference Manual
9
Backlight Brightness
Set the brightness of the screen with Backlight Brightness. The backlight can be set to any of 4 levels of
brightness.
„ Backlight Settings - Adjustment Procedure
• Before setting the Backlight Brightness, disable the Write Filter. When the Write Filter is
enabled, the change is not reflected.
Enabling the Write Filter after changing the setting is recommended.
) "4.1 Write Filter Settings Procedure" (Page 1-7)
1-18
(1)
Double click the Control Panel’s [Backlight Brightness] icon on the Control Panel.
(2)
Select the required level of brightness. (4 levels)
(3)
Click [OK] and end.
Chapter 1 Windows XP Embedded
10
Notes on turning off the power
In the factory settings, the Write Filter function is set as disable. When data is written in the devices (except
CF card) that are not protected by the Write Filter, turning off the power may cause damage of the data.
„ When the Write Filter is enabled
It is not necessary to perform the shutdown procedure. Confirm that no data is being written into another
device, follow the steps of Safely Remove Hardware, and then turn off the power. However, the OS setting
changed and the data written to the CF card during the time will be canceled and lost when the power is turned
off.
<How to confirm that no data is being written into another device>
Hard Disk : Confirm that the LED of the IPC Series is turned off.
USB Device/PCMCIA : Confirm that no data is written on user's applications.
„ When the Write Filter is disabled
It is necessary to perform the shutdown procedure. Because the write protection is not enabled, the OS setting
changed and the data written to the CF card will be enabled.
1-19
Windows XP Embedded Reference Manual
11
Backup/Recovery of the CF Card
The Backup/Recovery Tool is only available from the Pro-face’s support site “Otasuke Pro!”
(URL http://www.pro-face.com/otasuke/)
For downloading or how to use the Backup/Recovery Tool, refer to “XP Embedded CF card backup recovery
tool” from the abovementioned website.
The Backup/Recovery Tool can be used only when the following conditions are satisfied.
•
Only a CF card of the same size made by Pro-face can be recovered.
•
Only an XP Embedded CF card made by Pro-face can be backed up.
• Back up the CF card after installing necessary application programs. Data cannot be
recovered without backup data.
• For backing up data, refer to “Backup” described in “How to Use” in the “XP Embedded
CF card backup recovery tool” on the Pro-face support site “Otasuke Pro!”
1-20
Chapter 1 Windows XP Embedded
12
Restrictions
•
Help document is not installed.
•
Memory used when starting Window XP Embedded is approximately 160 MB in the Japanese/English
version / Japanese version and approximately 130 MB in the Multilanguage version.
•
When the memory has 128MB, the XPE cannot be used. Use it with the memory that has 256MB or more.
•
The virtual memory function cannot be used. The OS may stop depending on the memory allocation of
application software used.
•
The function to save Cache in Internet Explorer and Internet Information Service is set as shown below
before shipment.
• Cache File: Minimum Value
• Internet Information Service: disable
• Since the cache files are saved on RAM DISK, those files are deleted when you turn off the XPE.
• The fanction of Windows Update is the online support to update Windows automatically and
make the system the newest condition. But XPE does not correspond to Microsoft’s Windows
Update Service. When executing Windows Update on the Internet, a certain update module will
fail. Do not execute installation on the Internet.
1-21
Windows XP Embedded Reference Manual
1-22
2
Troubleshooting
1
Problems and countermeasures ................................................................................... 2-2
2-1
Windows XP Embedded Reference Manual
1
Problems and countermeasures
• The newest manual, Driver and Utility can be downloaded from the Digital Electronics Corporation’s homepage.
Also often questions and helpful informations are uploaded as Q&A to Digital Electronics Corporation’s homepage.
Please refer them to the purpose of usage. http://www.pro-face.com/otasuke/
Problems
The installed software does not
work after rebooting the
computer.
Rebooting the computer cancels
the new setting.
Changing the Write Filter setting
EWFSettingTool (Write Filter’s
setting screen) does not work
properly.
Countermeasures and troubleshooting
Has the Write Filter, which disables data saving to the CF card, been
enabled?
) "4.1 Write Filter Settings Procedure" (Page 1-7)
) "4.1 Write Filter Settings Procedure" (Page 1-7)
Check if the CF card is set to the primary master (Disk 0) in the BIOS
setting.
) Refer to the system setting description in the instruction manual
of your panel computer.
Packet INternet Grouper (PING)
is blocked when accessing the
network.
Has the firewall been enabled? Change the setting according to the
following procedure:
1. Click the [Start] button to open [Control Panel].
2. Double-click [Network and Internet Connections] to open
[Network Connections].
3. Double-click [Local Area Connection] and click [Properties] to
open [Local Area Connection Properties].
4. On the [Advance] tab, select [Windows Firewall] and open
[Settings].
5. On the [Advanced] tab, select [ICMP] and open [Settings].
6. Check [Allow incoming echo request].
Recovering the data
Download the Recovery Tool from the Pro-face’s support site
“Otasuke Pro!” and recover the data. It is necessary to backup the CF
card using the Recovery Tool before recovering the data.
Backing up the CF card
) "11 Backup/Recovery of the CF Card" (Page 1-20)
) "11 Backup/Recovery of the CF Card" (Page 1-20)
The touch point is displaced.
Has the touch point been corrected?
) 8 Using Touch Panel Operations "„Correction procedure for
touch point" (Page 1-17)
My user name and password can
not be remembered when accessing to the web server by Internet
Explorer.
2-2
[Remember my password] of the web server's login dialog box will not
function with the user account which has changed the Security ID.
In the following cases, create a new user account and log in again.
• When the Security ID has not changed since your purchase
• When the Security ID has changed after creating an user account
Chapter 2 Troubleshooting
Problems
When installing the software to
XPE, a dialog box name, [Files
Needed] appears
Countermeasures and troubleshooting
Type the path of the file name in [Copy files from:] that is requested
by the [Files Needed] dialog box.
Requested the DLL file(***.DLL): C:\WINDOWS\System32
Requested the SYS file(***.SYS): C:\WINDOWS\System32\drivers
When the files do not exist in the path above, please contact your
local distributor.
2-3
Windows XP Embedded Reference Manual
2-4
Appendices
1
[IN-fINITY soft KeyClick32] Agreement.........................................................................A-2
2
[DMC Corporation Mouse Emulation Software] SLA ....................................................A-3
A-1
Windows XP Embedded Refelence Manual
1
[IN-fINITY soft KeyClick32] Agreement
[IN-fINITY soft KeyClick32] Agreement
Digital Electronics Corporation shall be in no case liable for any loss or damages to you or any third party whatsoever
arising from any faulty performance of IN-fINITY soft, nor shall be responsible to correct such error of the software
program in question.
A-2
Appendices
2
[DMC Corporation Mouse Emulation Software] SLA
[DMC Corporation Mouse Emulation Software(TSC-1310D/DD)] Software License Agreement
Before unsealing and using this product, please read the following license agreement carefully:This license agreement
regarding the following software product (hereinafter called “product”) is concluded between you the individual or entity
licensing the product (hereinafter called (“licensee”) and DMC Co., Ltd. (hereinafter called “DMC”). With unsealing,
installing, copying or using the product, the licensee is regarded to agree this contract and the contract is in force.
Please confirm and understand this agreement fully in advance. If you do not agree this contract, do not unseal, install,
copy or use the software product at all. In such a case, please return the product at an unused state to the place you the
licensee purchased it. Your payment will be returned to the licensee.
1.Copyright
The copyright of the software product belongs to Touch-Base, Ltd.
2.License
For the programs included in this product and the documents related to it, DMC grants untransferable nonexclusive
license to licensee, which permits use of the product under the following conditions:
(1) When a licensee does not purchase the license which permits the licensee to use a licensed product and its copy(s)
and/or the license which permits use of the product on multiple computers, the licensee is granted the right to use the
product on a single computer.
(2) The licensee can create one copy of the product for archival purposes. For the other purposes, copying the whole or
part of the product is strictly prohibited whichever medium you use.
(3) The licensee shall display the copyright notice and other necessary information which is the same as that for the
product on every copy of the product.
(4) The intangible property right of the product and its copy(s) belong to DMC or the DMC supplier.
3.Term of use
This contract shall maintain its validity from conclusion of the contract to the cancellation by DMC or the license.
4.Termination of the right of use
(1) The licensee can at any time terminate the right to use the product by expunging or destroying the product and all the
copied contents.
(2) When a licensee contravenes these license contents, DMC can notify the licensee of termination of the right to use the
product. In this case, the licensee shall return the product or all the copied contents to DMC within one month.
A-3
Windows XP Embedded Refelence Manual
5.Limited Warranty
(1) DMC guarantees that 90 days after the licensee purchased the product, neither material nor manufacturing flaws shall
be found at the medium where the product has been recorded or stored. If any errors related to the material or
manufacturing is recognized when the product is installed, we shall replace the medium used to install the product on
the condition that we are notified of it within the guaranteed period.
(2) DMC shall grant the right to use the product at a state it has been supplied without explicit or implicit guarantee
except for replacement of the medium containing product described in the above clause. Further, we do not guarantee
that the product is suitable as useful for the licensee’s specific purpose of use and that execution of the product is
neither interrupted nor an error is found at its execution.
(3) The responsibility attributable to DMC based on this agreement is limited to replacement of the medium containing
the product, and DMC shall not assume any responsibility for the explicit or implicit guarantee including the other
legal warranty against a defect and a liability for reparation given from a third party to the licensee regarding the
licensee’s profit loss caused by the product, damage arising from a special circumstance and the damage against data
or intangible property right.
6.License’s obligation
The licensee shall recognize that the product shall possess the confidential information or property information including
the intangible property right protected by the Copyright Act and shall not take the following actions:
(1) Use and copying of the product against the terms of the license and disassembling, reverse engineering, and
modifying the product.
(2) Deletion and/or change of display of the intangible property right including the copyright displayedon the medium
containing the product.
7.Restrictions on Export
When the product is subjected to the regulation of the Foreign Exchange and Foreign Trade Control Act and the laws and
regulations accompanying it and the Export, the licensee shall observe the corresponding laws and regulations and rules.
DMC Co.,Ltd.
http://www.dmccoltd.com
Hironokougyoudanchi, Hirono-machi, Futaba-gun, Fukushima
979-0401, Japan
Phone: +81-240-27-4030 Fax: +81-240-27-4025
A-4
Download PDF