Beltronics | RX75PLUS - RX-75 PLUS Radar Detector | Owner`s manual | Beltronics RX75PLUS - RX-75 PLUS Radar Detector Owner`s manual

22292_Bel ProRemote_Manual
11/20/06
11:52 AM
Page 1
IMPORTANT NOTES
Read This First
Please read both sides of these instructions before starting your installation.
For the easiest trouble-free installation, install the Interface first, and wire it to a
12-volt switched circuit.
Then before installing the other components, plug all of them into the Interface
and power up the unit to confirm proper operation.
CUSTOM INSTALLED
RADAR DETECTOR AND
LASER “BLOCKING” SYSTEM
MODE L RX75 PLUS
Important Installation Warnings
1 A professional installer must install your
BEL
M ODE L
RX75
PLUS
new BEL
. Installation of
this system requires experience and
expertise in automotive electronics. Car
Audio specialists and many car dealers
can install BEL
for you.
Performance Warning
To get the best performance possible, the
mounting location of the Radar Receiver is
critical. Although radar signals will pass
through some types of plastic, mounting
the Radar Receiver so that it has a clear
“view” of the road will ensure maximum
warning.
2 Attempting to install this product
Interface
Front Radar Receiver
• Miniature weather-proof Radar Receiver
• Universal mounting bracket with stainless steel hardware
• Built-in 6 foot shielded cable with waterproof connector
• 13 foot shielded cable with in-line grommet and waterproof
connector
• 12 nylon wire ties to secure cable
Front Laser “Blockers”
• Weather-proof sensor
• 13 foot shielded cable with in-line grommet
• Universal mounting bracket with stainless steel hardware
• Central module connects to switched 12-volt power and ground
• All components plug directly in using modular connections
• 3M connector taps into existing vehicle wiring
Rear Laser Receiver
• Weatherproof license plate mounted sensor
• 30-foot cable with modular connector
Documentation
• Comprehensive Owner’s Manual
• Installation Manual
Built-in Diagnostics
User Display
• User Display mounts easily to instrument pod, dashboard,
or console
• Velcro and adhesive pads provided for secure mounting
without expertise in automotive
electronics installation can cause
personal injury, or damage to your
vehicle.
• Confirms all components are operational
5442 West Chester Road, West Chester, Ohio 45069
Sales/Service 800-341-2288 • www.beltronicspro.com
©2003 SWS™ is a trademark of SWS LC. Features, specifications and prices subject to change without notice.
3 If your vehicle is damaged during
installation, its safety systems may be
compromised, which could cause
personal injury or property damage.
4 Improper installation may void
the warranty.
Since Laser signals will not pass through
any objects, including plastic, it is critical
that the Laser Receivers be mounted
perfectly level, and have an unobstructed
“view” of the road.
22292_Bel ProRemote_Manual
11/20/06
11:52 AM
Page 2
BEL
Installation Manual
(top or bottom).
2 Mount Laser Receiver to plate using
P L U S
B
2 Using the built-in mounting holes on the
Receiver, or the supplied right-angle mounting
bracket, mark location. Drill pilot holes in the
vehicle if necessary.
3 Mount Radar Receiver using the supplied
hardware. (If right-angle mounting bracket is
used, secure Radar Receiver to the rightangle bracket first, then install bracket with
Radar Receiver to the vehicle.)
3 Route wire through trunk compartment,
and into the vehicle’s interior.
12 Volt
Power
Line
E
FRONT
A Front Radar Receiver
1 Determine the best location for the Radar
Receiver. The best location is typically under
the bumper, or inside the front grill of the
vehicle. For the best radar performance,
install the Radar Receiver horizontally, with a
clear “view” of the road.
supplied mounting bracket.
H
A
C
D
F
Y-Connector
4 Insert connector to jack labeled “Rear
Laser Receiver” on Interface.
TIPS
1. Do not block license plate illumination.
2. Do not cover any required license plate
information.
REAR
R X 75
1 Remove two license plate screws,
Interior of Vehicle
M O D E L
G Rear Laser “Blocking” Module
G
INSTALLATION ALTERNATIVES:
1. Cable can be routed under vehicle
(keep away from hot and moving parts)
then brought into the vehicle’s interior.
2. Cable can be cut if necessary for
routing. Reconnect and solder each of
the three wires, and seal with heatshrink tubing.
I
B
Note:
1. Do not drill holes in the receiver itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.
H Remote Mute/Volume Adjust
1 Determine best location for the
Remote Mute Button.
2 Clean surface area.
3 Remove paper backing on the back of
the button, and press onto surface.
B Front Laser “Blocking” Module
4 Route cable and plug into jack marked
1 Determine best location for the Laser Receiver.
“Mute” on Interface.
For optimum performance, install the Laser Receiver
near the front license plate if possible, with a clear “view” of the road.
2 Using the supplied mounting bracket, mark location. Drill pilot
holes in the vehicle if necessary.
3 Mount the Laser Blockers using the supplied hardware, making
sure that it is level to the road.
Note:
1. Do not drill holes in the Laser Receiver itself.
2. Thoroughly investigate location before drilling any holes.
3. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.)
4. Do not splice cable.
5. Make certain that the Laser Blocker is level, and has a
clear “view” of the road.
Note:
1. Connection between the radar receiver, and the receiver cable,
must be located in a dry location under hood.
2. Only drill hole in firewall after thoroughly investigating location
first, ensuring no other wires, hoses, etc. will be damaged.
3. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.).
4. Do not splice cable.
D Laser “Blocking” Cables
1 Route Laser Receiver cable to firewall, and secure with zip-ties
(included).
2 Route Laser cable into the vehicle’s interior. If there is not a
WARNING
suitable opening, drill a 13/32" or 7/16" hole.
Laser Blockers MUST be mounted level (+/-5 degrees) to the road to
work properly.
3 Pull cable through firewall, and plug connector into jack marked
“Front Laser/Blocker” on Interface.
C Radar “Blocking” Cable
4 Pull grommet (located on cable) through the firewall to seal the
1 Connect the receiver cable to the receiver.
hole. Use silicone sealant (not supplied) if necessary.
2 Route cable to firewall, and secure with zip-ties (included).
Note:
1. Only drill hole in firewall after thoroughly investigating location
first, ensuring no other wires, hoses, etc. will be damaged.
2. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.).
3. Do not splice cable.
3 Route receiver cable into the vehicle’s interior. If there is not a
suitable opening, drill a 13/32" or 7/16" hole.
4 Pull cable through firewall, and plug connector into the jack labeled
“Front Radar” on the Interface.
5 Pull grommet (located on the receiver cable itself) through the
firewall to seal the hole. Use silicone sealant (not supplied) if necessary.
E User Display
1 Determine the best location for the User Display in the
vehicle’s interior. (Consult customer if necessary.)
Test
After all components are installed correctly:
1 Turn vehicle’s ignition to the “on” position.
2 Install User Display using supplied velcro, or double-sided tape.
2 Turn BEL Pro
Remote Plus on by pressing the Power button.
3 Route cable and plug into jack marked “Display” on Interface.
3 BEL Pro
Note:
1. Make certain that the User Display is clearly visible from the
driver’s position, and that the controls can be easily accessed
without interfering with normal driving.
4 If any error messages come up, see appropriate section of
Remote Plus will cycle through a startup sequence.
the Owner’s Manual for details.
I External Speaker
F Interface
1 Install Interface under the dash using supplied zip-ties.
DO NOT MOUNT IN ENGINE COMPARTMENT.
2 Connect black wire (–) to ground, and red-striped wire (+) to a
switched 12-volt supply. (If BEL Pro Remote Plus is left in the “on”
position, it will automatically power on and off with the ignition).
Use blue 3M connector (provided) to tap into existing circuit if
needed.
1 Install the amplified speaker in the
desired location using the supplied
mounting bracket and hardware.
2 Snap the amplified speaker into the
bracket.
3 Attach the red ( + ) wire to a switched
power supply in the vehicle.
4 Attach the black ( – ) wire to chassis
3 Radar Receiver, front Laser Receiver, rear Laser Receiver, and
ground.
Display Controller all plug into the Interface. (Be sure to plug all
cables into the correct labeled jacks.)
5 Insert the 3.5mm plug into the external
speaker jack on the 5 pin interface
connector.
Download PDF