REMOTE WALL FAN ASSEMBLY & USER LEAFLET

REMOTE WALL FAN ASSEMBLY & USER LEAFLET
REMOTE WALL FAN
ASSEMBLY & USER
LEAFLET
Please read these instructions carefully
before operating the Fan
FAN ASSEMBLY INSTRUCTIONS
1) Unscrew the impeller retaining cap by turning it clockwise and the guard retaining nut anti-clockwise
remove both of them from the motor shaft.
2) Take the rear guard section and slide it over the threaded screw on the fan body (making sure the
small pegs line up with the holes in the guard).
3) Screw on the plastic nut to secure the rear guard in place.
4) Push the impeller on to the motor shaft until it reaches the stop.
5) Screw on the impeller-retaining cap in an anti-clockwise direction to secure the impeller into
position.
6) Hook the front guard on to the rear guard section at the top.
7) Click the two guard sections together then push the clip on the bottom of the grille upwards until it
stops. The screw at the bottom of the grille MUST be tightened to lock the grille in position.
IMPORTANT
♦
♦
♦
Ensure that the voltage marked on the underside of the fan agrees with your mains voltage.
This fan is a class 1 appliance and MUST BE EARTHED.
The wires in the mains lead are coloured in accordance with the following code:BLUE – NEUTRAL
♦
♦
♦
BROWN – LIVE
GREEN - EARTH
This fan must NOT be used in a bathroom.
Always ensure that a fuse approved to BS 1362 is fitted and that it is the correct rating for the
appliance.
IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
MOUNTING OF THE FAN
1) Place the metal hanging bracket provided against the wall in the position
you wish the fan to go.
2) Mark through the holes in the bracket with a pencil/pen and then remove
the bracket.
3) With suitable fixings appropriate to the surface that the fan is to be
mounted on, fix the bracket to the wall.
4) Now hang the fan to the wall, by locating the slot on the rear of the fan
over the hanging bracket.
5) There is also a plastic holder for the remote control, this can be fixed to the
wall in the same way as stated above.
455520B
0211
OPERATION OF THE FAN
The remote control has the following functions: OFF
When the fan is running press this button once to stop the fan.
SPEED
To turn the fan ON press this button once, The fan will start on the low speed setting.
Press the “speed” button again to select the medium speed setting.
Another press of the “speed” button will select the high speed setting.
Once more will go back to the low speed setting and so on.
SOFT WIND
This function allows the fan to automatically change the speed
of the fan as follows: LOW > MED > STOP > LOW > MED > STOP> e.t.c
TIMER
This will allow you to select 4 pre-set times as follows: Press
Press
Press
Press
once for 1 hour
twice for 2 hours
three times for 4 hours
Four times for 8 hours
An LED will light up against each time that has been selected.
By pressing the timer button once more will cancel the timer function.
SWING
By pressing this button the fan will start to oscillate.
Pressing this button once more will stop the fan oscillating.
The fan speed, swing and OFF buttons can also be selected manually on the fan.
CLEANING
Plastic parts should only be cleaned with mild soap and a damp cloth or sponge. Never use solvent or
abrasive cleaners.
NOTES FOR SAFE OPERATION
♦
♦
♦
♦
♦
Never insert any objects through the guard when the fan is running.
Always disconnect the fan when removing the guard for cleaning.
Do not use the fan near an open window. (Rain may create an electrical hazard).
Do not leave the remote control unit in direct sunlight (e.g. left on a window seal for long periods).
Do not use the fan in areas of high humidity. Or in a area where the temperature is higher than
40.deg C
THINGS TO DO IF THE FAN DOES NOT OPERATE BY THE REMOTE
1) The remote control works on having a line of sight to the fan, If there is an obstacle between fan
and remote you will not be able to change control functions.
2) The remote control has a range of 5 metres, if you are trying to operate the fan from a longer
distance it will not work.
3) Check that the batteries in the remote control are not flat, or that they are in the wrong way round.
(This can be done by sliding off the cover on the rear of the controller)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement