BOB | INFANT CAR SEAT ADAPTER | Infant Car Seat Adapter instructions

I nfant C ar S eat A dapter i nstructions
(800) 893-2447 www.bobgear.com email- info@bobgear.com
Phone: (208) 375-5171 Fax: (208) 375-5172, BOB Trailers, Inc. 5475 Gage St. Boise, ID 83706
MA0516B
Congratulations on your purchase of the BOB Infant Car Seat Adapter
(ICSA). It is designed to allow the attachment of an Infant Car Seat
to your BOB Stroller. Please see the table below for the details of
compatible strollers and car seats.
Fastener
Restraint
Belt
BOB Stroller Model Year Compatibility
Model Year(s)
2005 and newer
2005 and newer
2005 and newer
2005 and newer
2005 and newer
Model
Sport Utility Stroller
Sport Utility Stroller D’Lux
Ironman
Revolution
Stroller Strides
Brand
Britax®
Graco®
Peg Perego®
Model
Companion®
Snug Ride®
Primo ViaggioTM
Serial Number*
AA000001 and higher
AB000001 and higher
AC000001 and higher
AF000001 and higher
AG000001 and higher
Support
Fastener
WARNINGS
. The BOB ICSA is designed for use with single seat BOB Strollers
and recommended Infant Car Seats. Children should not be placed
directly in the BOB Stroller seat with the ICSA installed.
The ICSA Restraint Belt interferes with the proper function of the
safety harness system and the Accessory Tube of the ICSA can
interfere with accessibility. ICSA must be removed from the BOB
Stroller prior to using with a child directly in the seat.
. Read and understand stroller owner’s manual before use.
. Read and understand car seat owner’s manual before use.
. Follow assembly instructions. Failure to properly install this accessory
product may result in accidents, severe injury or death. If you are
not sure you can install this accessory, contact your dealer and
arrange for them to perform the installation.
. Never leave children unattended in the stroller/car seat.
. Always secure the car seat with the restraint belt when the car
seat is placed in the stroller.
. Always use seat harness of Infant Car Seat to avoid children from
falling out of stroller.
. Refer to your Infant Car Seat owner’s manual for maximum capacity
limitations.
. Always keep your Infant Car Seat handle vertical and locked position
when used in stroller to protect your child.
. This product is not a universal adapter. Consult chart for compatibility
with infant car seat brand and model.
. Do not strap parcels or bags to the stroller handle or to this product
when installed on your stroller as it affects the balance and stability
of the stroller and can cause it to tip over.
. Do not run or jog when using the Infant Car Seat Adapter.
. Do not use off-road or on uneven terrain when using the car seat
adapter.
. Children develop at different rates. Consult with your pediatrician
regarding the suitability of the stroller use with your child.
BOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE OR FAILURE
THAT RESULTS FROM OWNERS FAULTY ASSEMBLY OR
MAINTENANCE
AFTER SHIPPING.
Serial Number
Located On
Assembly
Inside of Right
Instructions
Swingarm
TOOLS NEEDED:
To perform the
installation, you will
need two Philips
Screwdrivers.
Fig. A Serial Number Location
Pivot-Plug
Year(s)
2003 & newer
2003 & newer
2003 & newer
If you are unclear on any point, contact your dealer or BOB before
use.
Reference Fig. 1 as it
describes the various
parts of the ICSA.
Screw
Sex Bolt,
Female
* Reference Fig. A for serial number location.
Car Seat Compatibility
Before attempting to install your new ICSA, read and understand
these instructions completely to insure proper installation.
Sex Bolt,
Male
Accessory
Tube
Main
Tube
Sex Bolt,
Male
Fig. 1 Anatomy of the Infant Car Seat Adapter
Aft Stay
Vertical
Bonnet
Stays
Forward Stay
Adjacent
Lower
Handlebar
Fabric
Screw
Swingarm
Pivot Tube
Fig. 2 Attachment Point Locations
Sex Bolt,
Female
Inner
Pivot
Plug
Swingarm
Pivot Tube
Outer
Pivot Plug
Pivot
Bracket
Fig. 3 Pivot Hardware Installation
Set parking brake.
Refer to BOB stroller
owner’s manual for
use and function of
brake.
1. UNPACK: Remove
all packaging material
from product.
Note orientation of
pivot parts and
hardware (Item No’s.
4, 5, & 6). When
installing these parts
they should be
assembled in same
orientation as shown
in Fig. 1.
2. LOCATE THE
ATTACHMENT
POINTS ON
STROLLER: Fig. 2
shows the swingarm
pivot tube locations
where the pivot-plugs
will be installed. Place
the 4 pivot-plugs
(Item 4) inside each
end of both swingarm
pivot tubes of your
BOB stroller as
shown in Fig. 3. In
order to locate and
view the inside
locations, it may be
helpful to push the
fabric seat of stroller
forward and out of the
way.
3. INSTALL THE PIVOT HARDWARE ON STROLLER: With pivot
plugs installed, next install the pivot hardware. Insert one of the female
(long) parts of sex bolt (Item 5) through each pair of pivot plugs (Item
4) from the inside, as shown in Fig. 3, so the threaded ends are just
flush with the outside pivot-plugs.
4. POSITION THE
ICSA ASSEMBLY:
Make sure both the
supports (Item 7) are
rotated forward
before installing ICSA
on stroller as shown
in Fig. 4.
Support
Rotated
Forward
Pivot
Bracket
Stretch both ends of
the ICSA main tube
evenly over the pivot
brackets of the
stroller. Be careful not
to pinch your fingers.
One side at a time,
Main
locate each hole at
Tube
the end of the main
tube of the ICSA
Sex Bolt,
assembly and line up
Male4 x 8mm
with pivot hardware
Fig. 4 Main Tube Aligned for Assembly
on stroller.
One side at a time,
push female part of
sex bolt (Item 5)
through ICSA main
tube, and install male
part of sex bolt (Item
Fastener
6). Tighten pivot
hardware using both Grommet
Of
screwdrivers. Tighten
completely (Torque to Seat Fabric
Lower
10-15 In-lbf).
Fabric Screw
Support
Rivet Nut
5. INSTALL UPPER
Between
COMPONENTS:
Inboard
Move stays of stroller
Bonnet
bonnet (sun canopy) Restraint Belt
Stay &
Grommet
to a vertical position
Frame
as shown in Fig. 2.
Locate and remove
the lower fabric screw
on each side of
handlebar, Fig 2.
Work on one side at
a time, keeping the
Fig. 5 Upper Component Installation
other side Support
(Item 7) forward as
shown in Fig. 4.
Hold Restraint Belt
Rotate Main Tube
Perpendicular to
(Item 1) back, routing
Handlebar When
the Support (Item 7)
Tightening Fastener
between inboard
bonnet stay and
stroller frame until the
hole in the support is
aligned with lower
fabric screw threads
(rivet nut) on
handlebar. Assembly Fastener
sequence shown in
Fig. 5. Make sure
restraint belt (Item 9) Fig. 6 Proper Restraint Belt Orientation
is oriented with pull
ring facing out as
shown in Fig. 7. Push
fastener (Item 8) with
pointed end carefully
through support
(Item 7), grommet of
safety restraint belt
(Item 9), then
through fabric
grommet and into
rivet nut on
handlebar. Start
thread by hand.
Buckle and Pull Ring
Using screwdriver,
Oriented To Outside
thread the fastener
straight into the
Fig. 7 Restraint Belt Properly Installed
handlebar. Be
careful: do not crossthread. The fastener
is designed to anchor
into the interior
opposite wall of
handlebar.
Hold the restraint belt
in the proper position
perpendicular to
frame as shown in
Fig. 6 and tighten
Fastener (Item 8).
Torque to 10-15 In-lbf
(1-2 N-m). Properly
installed Restraint Belt
shown in Fig. 7.
Seat Reclined
Canopy Against
Handlebar
Restraint
Belt
Outside
Stroller
Accessory
INSTRUCTIONS
Tube
FOR INSTALLING
AND SECURING
Fig. 8 Correct Configuration for Britax
YOUR INFANT CAR
SEAT IN BOB ICSA Companion
Your infant car seat
can be placed in and
removed from a BOB
Stroller with the infant
car seat occupied or
vacant. However,
when installing car
seat in the ICSA for
the first time, test fit
with the car seat
unoccupied to ensure
you understand the
process and to make
sure the seat recline
Both Car Seat Grooves
and Accessory Tube
Placed on Accessory Tube
set up is correct for
your type of Infant Car
Fig. 9 Britax Companion Placed on
Seat.
ICSA
Installation
instructions for the
compatible brands
and models below.
Follow the appropriate
instructions for your
infant car seat.
BRITAX Companion
Restraint Belt
1. Set parking brake. Routed Through
Refer to BOB stroller Slots in Car Seat
owner’s manual for
And Buckled
use and function of
brake.
2. Confirm Accessory
Tube (Item 2) is
installed on ICSA and
secured in place by
two screws (Item 3). Fig. 10 Britax Companion Secured With
The ICSA is supplied
Restraint Belt
with the Accessory
Tube installed.
3. Fig. 8 shows the ICSA and stroller in the correct configuration to
accept the Britax Companion.
4. Recline BOB Stroller seat all the way back. Refer to BOB stroller
owner’s manual for seat-recline feature strap(s) location and function.
5. Rotate BOB stroller canopy all the way back against the handlebar,
Fig. 8.
6. Unbuckle Restraint Belt. Move each belt end outside the stroller
seat so they will not be trapped under the BRITAX, Fig. 8.
7. With car seat handle in vertical (carry) position, gently place the
BRITAX rear facing in the seat of BOB Stroller w/ICSA in a straight
downward motion.
8. Align the bottom channels or grooves of the BRITAX plastic frame
so they rest on the Accessory Tube (Item 2) as shown in Fig. 9.
9. Route restraint belt through slots in car seat and fasten buckle as
shown in Fig. 10.
10. Pull on the ring to tighten the Restraint Belt. When tightened
I nfant C ar S eat A dapter i nstructions
(800) 893-2447 www.bobgear.com email- info@bobgear.com
Phone: (208) 375-5171 Fax: (208) 375-5172, BOB Trailers, Inc. 5475 Gage St. Boise, ID 83706
MA0516B
Congratulations on your purchase of the BOB Infant Car Seat Adapter
(ICSA). It is designed to allow the attachment of an Infant Car Seat
to your BOB Stroller. Please see the table below for the details of
compatible strollers and car seats.
Fastener
Restraint
Belt
BOB Stroller Model Year Compatibility
Model Year(s)
2005 and newer
2005 and newer
2005 and newer
2005 and newer
2005 and newer
Model
Sport Utility Stroller
Sport Utility Stroller D’Lux
Ironman
Revolution
Stroller Strides
Brand
Britax®
Graco®
Peg Perego®
Model
Companion®
Snug Ride®
Primo ViaggioTM
Serial Number*
AA000001 and higher
AB000001 and higher
AC000001 and higher
AF000001 and higher
AG000001 and higher
Support
Fastener
WARNINGS
. The BOB ICSA is designed for use with single seat BOB Strollers
and recommended Infant Car Seats. Children should not be placed
directly in the BOB Stroller seat with the ICSA installed.
The ICSA Restraint Belt interferes with the proper function of the
safety harness system and the Accessory Tube of the ICSA can
interfere with accessibility. ICSA must be removed from the BOB
Stroller prior to using with a child directly in the seat.
. Read and understand stroller owner’s manual before use.
. Read and understand car seat owner’s manual before use.
. Follow assembly instructions. Failure to properly install this accessory
product may result in accidents, severe injury or death. If you are
not sure you can install this accessory, contact your dealer and
arrange for them to perform the installation.
. Never leave children unattended in the stroller/car seat.
. Always secure the car seat with the restraint belt when the car
seat is placed in the stroller.
. Always use seat harness of Infant Car Seat to avoid children from
falling out of stroller.
. Refer to your Infant Car Seat owner’s manual for maximum capacity
limitations.
. Always keep your Infant Car Seat handle vertical and locked position
when used in stroller to protect your child.
. This product is not a universal adapter. Consult chart for compatibility
with infant car seat brand and model.
. Do not strap parcels or bags to the stroller handle or to this product
when installed on your stroller as it affects the balance and stability
of the stroller and can cause it to tip over.
. Do not run or jog when using the Infant Car Seat Adapter.
. Do not use off-road or on uneven terrain when using the car seat
adapter.
. Children develop at different rates. Consult with your pediatrician
regarding the suitability of the stroller use with your child.
BOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE OR FAILURE
THAT RESULTS FROM OWNERS FAULTY ASSEMBLY OR
MAINTENANCE
AFTER SHIPPING.
Serial Number
Located On
Assembly
Inside of Right
Instructions
Swingarm
TOOLS NEEDED:
To perform the
installation, you will
need two Philips
Screwdrivers.
Fig. A Serial Number Location
Pivot-Plug
Year(s)
2003 & newer
2003 & newer
2003 & newer
If you are unclear on any point, contact your dealer or BOB before
use.
Reference Fig. 1 as it
describes the various
parts of the ICSA.
Screw
Sex Bolt,
Female
* Reference Fig. A for serial number location.
Car Seat Compatibility
Before attempting to install your new ICSA, read and understand
these instructions completely to insure proper installation.
Sex Bolt,
Male
Accessory
Tube
Main
Tube
Sex Bolt,
Male
Fig. 1 Anatomy of the Infant Car Seat Adapter
Aft Stay
Vertical
Bonnet
Stays
Forward Stay
Adjacent
Lower
Handlebar
Fabric
Screw
Swingarm
Pivot Tube
Fig. 2 Attachment Point Locations
Sex Bolt,
Female
Inner
Pivot
Plug
Swingarm
Pivot Tube
Outer
Pivot Plug
Pivot
Bracket
Fig. 3 Pivot Hardware Installation
Set parking brake.
Refer to BOB stroller
owner’s manual for
use and function of
brake.
1. UNPACK: Remove
all packaging material
from product.
Note orientation of
pivot parts and
hardware (Item No’s.
4, 5, & 6). When
installing these parts
they should be
assembled in same
orientation as shown
in Fig. 1.
2. LOCATE THE
ATTACHMENT
POINTS ON
STROLLER: Fig. 2
shows the swingarm
pivot tube locations
where the pivot-plugs
will be installed. Place
the 4 pivot-plugs
(Item 4) inside each
end of both swingarm
pivot tubes of your
BOB stroller as
shown in Fig. 3. In
order to locate and
view the inside
locations, it may be
helpful to push the
fabric seat of stroller
forward and out of the
way.
3. INSTALL THE PIVOT HARDWARE ON STROLLER: With pivot
plugs installed, next install the pivot hardware. Insert one of the female
(long) parts of sex bolt (Item 5) through each pair of pivot plugs (Item
4) from the inside, as shown in Fig. 3, so the threaded ends are just
flush with the outside pivot-plugs.
4. POSITION THE
ICSA ASSEMBLY:
Make sure both the
supports (Item 7) are
rotated forward
before installing ICSA
on stroller as shown
in Fig. 4.
Support
Rotated
Forward
Pivot
Bracket
Stretch both ends of
the ICSA main tube
evenly over the pivot
brackets of the
stroller. Be careful not
to pinch your fingers.
One side at a time,
Main
locate each hole at
Tube
the end of the main
tube of the ICSA
Sex Bolt,
assembly and line up
Male4 x 8mm
with pivot hardware
Fig. 4 Main Tube Aligned for Assembly
on stroller.
One side at a time,
push female part of
sex bolt (Item 5)
through ICSA main
tube, and install male
part of sex bolt (Item
Fastener
6). Tighten pivot
hardware using both Grommet
Of
screwdrivers. Tighten
completely (Torque to Seat Fabric
Lower
10-15 In-lbf).
Fabric Screw
Support
Rivet Nut
5. INSTALL UPPER
Between
COMPONENTS:
Inboard
Move stays of stroller
Bonnet
bonnet (sun canopy) Restraint Belt
Stay &
Grommet
to a vertical position
Frame
as shown in Fig. 2.
Locate and remove
the lower fabric screw
on each side of
handlebar, Fig 2.
Work on one side at
a time, keeping the
Fig. 5 Upper Component Installation
other side Support
(Item 7) forward as
shown in Fig. 4.
Hold Restraint Belt
Rotate Main Tube
Perpendicular to
(Item 1) back, routing
Handlebar When
the Support (Item 7)
Tightening Fastener
between inboard
bonnet stay and
stroller frame until the
hole in the support is
aligned with lower
fabric screw threads
(rivet nut) on
handlebar. Assembly Fastener
sequence shown in
Fig. 5. Make sure
restraint belt (Item 9) Fig. 6 Proper Restraint Belt Orientation
is oriented with pull
ring facing out as
shown in Fig. 7. Push
fastener (Item 8) with
pointed end carefully
through support
(Item 7), grommet of
safety restraint belt
(Item 9), then
through fabric
grommet and into
rivet nut on
handlebar. Start
thread by hand.
Buckle and Pull Ring
Using screwdriver,
Oriented To Outside
thread the fastener
straight into the
Fig. 7 Restraint Belt Properly Installed
handlebar. Be
careful: do not crossthread. The fastener
is designed to anchor
into the interior
opposite wall of
handlebar.
Hold the restraint belt
in the proper position
perpendicular to
frame as shown in
Fig. 6 and tighten
Fastener (Item 8).
Torque to 10-15 In-lbf
(1-2 N-m). Properly
installed Restraint Belt
shown in Fig. 7.
Seat Reclined
Canopy Against
Handlebar
Restraint
Belt
Outside
Stroller
Accessory
INSTRUCTIONS
Tube
FOR INSTALLING
AND SECURING
Fig. 8 Correct Configuration for Britax
YOUR INFANT CAR
SEAT IN BOB ICSA Companion
Your infant car seat
can be placed in and
removed from a BOB
Stroller with the infant
car seat occupied or
vacant. However,
when installing car
seat in the ICSA for
the first time, test fit
with the car seat
unoccupied to ensure
you understand the
process and to make
sure the seat recline
Both Car Seat Grooves
and Accessory Tube
Placed on Accessory Tube
set up is correct for
your type of Infant Car
Fig. 9 Britax Companion Placed on
Seat.
ICSA
Installation
instructions for the
compatible brands
and models below.
Follow the appropriate
instructions for your
infant car seat.
BRITAX Companion
Restraint Belt
1. Set parking brake. Routed Through
Refer to BOB stroller Slots in Car Seat
owner’s manual for
And Buckled
use and function of
brake.
2. Confirm Accessory
Tube (Item 2) is
installed on ICSA and
secured in place by
two screws (Item 3). Fig. 10 Britax Companion Secured With
The ICSA is supplied
Restraint Belt
with the Accessory
Tube installed.
3. Fig. 8 shows the ICSA and stroller in the correct configuration to
accept the Britax Companion.
4. Recline BOB Stroller seat all the way back. Refer to BOB stroller
owner’s manual for seat-recline feature strap(s) location and function.
5. Rotate BOB stroller canopy all the way back against the handlebar,
Fig. 8.
6. Unbuckle Restraint Belt. Move each belt end outside the stroller
seat so they will not be trapped under the BRITAX, Fig. 8.
7. With car seat handle in vertical (carry) position, gently place the
BRITAX rear facing in the seat of BOB Stroller w/ICSA in a straight
downward motion.
8. Align the bottom channels or grooves of the BRITAX plastic frame
so they rest on the Accessory Tube (Item 2) as shown in Fig. 9.
9. Route restraint belt through slots in car seat and fasten buckle as
shown in Fig. 10.
10. Pull on the ring to tighten the Restraint Belt. When tightened
I nfant C ar S eat A dapter i nstructions
(800) 893-2447 www.bobgear.com email- info@bobgear.com
Phone: (208) 375-5171 Fax: (208) 375-5172, BOB Trailers, Inc. 5475 Gage St. Boise, ID 83706
MA0516B
properly, the belt will
hold the BRITAX
securely in place.
Make sure the tension
of the belt is not
constricting your child.
Before use, verify you
have installed your
Britax Companion
correctly as shown in
Fig. 11.
As final double check
before use, attempt to
remove car seat with
restraint belt in place
and securely
fastened. You should
not be able to remove
car seat without
unfastening restraint
belt.
To remove the
BRITAX:
1. Set parking brake.
2. Unbuckle the ICSA
restraint belt and
move out of way.
3. Lift the BRITAX
straight up and off the
BOB stroller with the
handle of the BRITAX
in the vertical (carry)
position.
4. Fasten restraint belt
when not in use to
prevent damage.
GRACO Snug Ride
Canopy Against
Handlebar
Handle in
Upright
Position
Seat
Reclined
Restraint Belt
Routed Through
Slots in Car Seat
And Buckled
To remove the
GRACO:
Restraint
Belt
Secured
Both Car Seat Grooves
Placed on Accessory Tube
Fig. 11 Britax Companion Installed on
ICSA
Seat Upright
As final double check
before use, attempt to
remove car seat with
the restraint belt in
place and securely
fastened. You should
not be able to remove
car seat without
unfastening restraint
belt.
Canopy Against
Handlebar
Restraint
Belt
Outside
Stroller
Accessory
Tube
Removed
1. Set parking brake.
Refer to BOB stroller Fig. 12 Correct Configuration for Graco
owner’s manual for
Snug Ride
use and function of
brake.
2. Remove Accessory
Tube (Item 2) on ICSA
by removing two
screws (Item 3) with
Philips screwdriver.
Both Car Seat Grooves
3. Fig. 12 shows the
Placed on Main Tube
ICSA and stroller in
the correct
configuration to
accept the Graco
Snug Ride.
4. Make sure BOB
Stroller seat is in the
upright position. Refer
Hook Under Main Tube
to BOB stroller
owner’s manual for
Fig. 13 Graco Snug Ride Placed on
seat-recline strap(s)
location and function. ICSA
5. Rotate BOB stroller
canopy all the way back against the handlebar, Fig. 12.
6. Unbuckle Restraint Belt. Move each belt end outside the stroller
seat so they will not be trapped under the GRACO, Fig. 12.
7. With car seat handle in vertical (carry) position, gently place the
GRACO rear facing in the seat of BOB Stroller w/ICSA in a straight
downward motion.
8. Align the bottom channels or grooves of the GRACO plastic frame
so they rest on the main tube (Item 1) as shown in Fig. 13. Confirm
the red plastic hook of the GRACO is under the main tube (Item 1).
9. Route restraint belt through slots in car seat and fasten buckle as
shown in Fig. 14.
10. Pull on the ring to tighten the restraint belt. When tightened properly,
the belt will hold the GRACO securely in place.
Make sure the tension of the belt is not constricting your child.
Before use, verify you have installed your Snug Ride correctly as
shown in Fig. 15.
1. Set parking brake.
2. Unbuckle the ICSA
restraint belt and
Fig. 14 Graco Snug Ride Secured With
move out of way.
Restraint Belt
3. Pull on red release
handle of the GRACO
while lifting straight up
Canopy Against
Handle in
and off the BOB
Handlebar
Upright
stroller with the handle
Position
of the GRACO in the
vertical (carry)
position.
4. Fasten restraint belt
when not in use to
Hook Under
Seat
prevent damage.
Main Bar
Upright
PEG PEREGO Primo
Viaggio
1. Set parking brake.
Refer to BOB stroller
owner’s manual for
use and function of
brake.
2. Confirm Accessory
Tube (Item 2) is
installed on ICSA and
secured in place by
two screws (Item 3).
The ICSA is supplied
with the Accessory
Tube installed.
3. Fig. 17 shows the
ICSA and stroller in
the correct
configuration to
accept the Peg
Perego Primo
Viaggio.
4. Make sure BOB
Stroller seat is in the
upright position. Refer
to BOB stroller
owner’s manual for
seat-recline strap(s)
location and function.
5. Rotate BOB stroller
canopy all the way
open, back against
the handlebar, Fig. 17.
6. Unbuckle Restraint
Belt. Move each belt
end outside the
stroller seat so they
will not be trapped
under the PEG
PEREGO, Fig. 17.
7. With car seat
handle in vertical
(carry) position, gently
place the PEG
PEREGO rear facing
in the seat of BOB
Stroller w/ICSA in a
straight downward
motion.
Restraint
Belt
Secured
Both Car Seat Grooves
Placed on Accessory Tube
Fig. 15 Graco Snug Ride Installed on
ICSA
Pull
Release
Handle
Hook
Retracted
For
Removal
Fig. 16 Graco Snug Ride Removal
Seat Upright
Canopy Against
Handlebar
8. Align the bottom
channels or grooves
of the PEG PEREGO
plastic frame so they
rest on the Accessory
Tube (Item 2) as
shown in Fig. 18.
9. Fasten buckle of
Restraint Belt over the
top of the PEG
PEREGO as shown in
Fig. 19.
10. Pull on the ring to
tighten the Restraint
Belt. When tightened
Both Car Seat Grooves
properly, the belt will
Placed on Accessory Tube
hold the PEG
PEREGO securely in
Fig. 18 Peg Perego Primo Viaggio
place.
Make sure the tension Placed on ICSA
of the belt is not
constricting your child.
Before use, verify you
have installed your
Primo Viaggio
correctly as shown in
Fig. 20.
As final double check
before use, attempt to
remove car seat with
the restraint belt. You
should not be able to
remove car seat
Restraint Belt
without unfastening
Routed Across
restraint belt.
Car Seat
And Buckled
To remove the PEG Fig. 19 Peg Perego Primo Viaggio
Secured With Restraint Belt
PEREGO:
1. Set parking brake.
2. Unbuckle the ICSA
Handle in
Canopy Against
restraint belt and
Upright
Handlebar
move out of way.
Position
3. Lift the PEG
PEREGO straight up
and off the BOB
stroller with the handle
of the PEG PEREGO
in the vertical (carry)
position.
Seat
4. Fasten restraint belt
Upright
when not in use to
prevent damage.
Restraint
Belt
Both Car Seat Grooves
Secured
Placed on Accessory Tube
Fig. 20 Peg Perego Primo Viaggio
Installed on ICSA
Restraint
Belt
Outside
Stroller
Accessory
Tube
Fig. 17 Correct Configuration for Peg
Pergeo Primo Viaggio
LIMITED WARRANTY
BOB Trailers Inc. takes pride in its workmanship and strives to
manufacture the best products possible. Therefore, we warranty the
ICSA against defects in material and workmanship subject to the
conditions listed below. Since no product is indestructible, it does not
cover defects attributable to or resulting from normal wear, abuse or
alteration.
. The ICSA is warranted for one year from the date of original
purchase.
. Warranty is only valid for the original purchaser.
. Proof of purchase is required to exercise this warranty.
. Labor and freight charges are not included.
. Normal wear, neglect, abuse, accidents, and improper use are not
covered by this warranty.
. Warranty claims must be made through an authorized dealer.
. This warranty is limited to the repair or replacement of the defective
part. BOB Trailers, Inc. shall in no event be responsible for
consequential or special damages.
. This Limited Warranty is the only express or implied warranty
applicable to BOB Trailers, Inc. Any implied warranties, including
warranties of merchantability and fitness shall be limited in scope
and duration in accordance with this limited warranty.
BŸOŸB, BŸOŸB Logo, and BOB are proprietary trademarks of BOB
Trailers, Inc.
Britax® and Companion® are registered trademarks of Britax Excelsior
Ltd. and related companies
Graco® and Snug Ride® are registered trademarks of Graco Children’s
Products, Inc.
Peg Perego® and Primo Viaggio™ are registered and proprietary
trademarks of Peg Perego S.P.A. Corporation
I nfant C ar S eat A dapter i nstructions
(800) 893-2447 www.bobgear.com email- info@bobgear.com
Phone: (208) 375-5171 Fax: (208) 375-5172, BOB Trailers, Inc. 5475 Gage St. Boise, ID 83706
MA0516B
properly, the belt will
hold the BRITAX
securely in place.
Make sure the tension
of the belt is not
constricting your child.
Before use, verify you
have installed your
Britax Companion
correctly as shown in
Fig. 11.
As final double check
before use, attempt to
remove car seat with
restraint belt in place
and securely
fastened. You should
not be able to remove
car seat without
unfastening restraint
belt.
To remove the
BRITAX:
1. Set parking brake.
2. Unbuckle the ICSA
restraint belt and
move out of way.
3. Lift the BRITAX
straight up and off the
BOB stroller with the
handle of the BRITAX
in the vertical (carry)
position.
4. Fasten restraint belt
when not in use to
prevent damage.
GRACO Snug Ride
Canopy Against
Handlebar
Handle in
Upright
Position
Seat
Reclined
Restraint Belt
Routed Through
Slots in Car Seat
And Buckled
To remove the
GRACO:
Restraint
Belt
Secured
Both Car Seat Grooves
Placed on Accessory Tube
Fig. 11 Britax Companion Installed on
ICSA
Seat Upright
As final double check
before use, attempt to
remove car seat with
the restraint belt in
place and securely
fastened. You should
not be able to remove
car seat without
unfastening restraint
belt.
Canopy Against
Handlebar
Restraint
Belt
Outside
Stroller
Accessory
Tube
Removed
1. Set parking brake.
Refer to BOB stroller Fig. 12 Correct Configuration for Graco
owner’s manual for
Snug Ride
use and function of
brake.
2. Remove Accessory
Tube (Item 2) on ICSA
by removing two
screws (Item 3) with
Philips screwdriver.
Both Car Seat Grooves
3. Fig. 12 shows the
Placed on Main Tube
ICSA and stroller in
the correct
configuration to
accept the Graco
Snug Ride.
4. Make sure BOB
Stroller seat is in the
upright position. Refer
Hook Under Main Tube
to BOB stroller
owner’s manual for
Fig. 13 Graco Snug Ride Placed on
seat-recline strap(s)
location and function. ICSA
5. Rotate BOB stroller
canopy all the way back against the handlebar, Fig. 12.
6. Unbuckle Restraint Belt. Move each belt end outside the stroller
seat so they will not be trapped under the GRACO, Fig. 12.
7. With car seat handle in vertical (carry) position, gently place the
GRACO rear facing in the seat of BOB Stroller w/ICSA in a straight
downward motion.
8. Align the bottom channels or grooves of the GRACO plastic frame
so they rest on the main tube (Item 1) as shown in Fig. 13. Confirm
the red plastic hook of the GRACO is under the main tube (Item 1).
9. Route restraint belt through slots in car seat and fasten buckle as
shown in Fig. 14.
10. Pull on the ring to tighten the restraint belt. When tightened properly,
the belt will hold the GRACO securely in place.
Make sure the tension of the belt is not constricting your child.
Before use, verify you have installed your Snug Ride correctly as
shown in Fig. 15.
1. Set parking brake.
2. Unbuckle the ICSA
restraint belt and
Fig. 14 Graco Snug Ride Secured With
move out of way.
Restraint Belt
3. Pull on red release
handle of the GRACO
while lifting straight up
Canopy Against
Handle in
and off the BOB
Handlebar
Upright
stroller with the handle
Position
of the GRACO in the
vertical (carry)
position.
4. Fasten restraint belt
when not in use to
Hook Under
Seat
prevent damage.
Main Bar
Upright
PEG PEREGO Primo
Viaggio
1. Set parking brake.
Refer to BOB stroller
owner’s manual for
use and function of
brake.
2. Confirm Accessory
Tube (Item 2) is
installed on ICSA and
secured in place by
two screws (Item 3).
The ICSA is supplied
with the Accessory
Tube installed.
3. Fig. 17 shows the
ICSA and stroller in
the correct
configuration to
accept the Peg
Perego Primo
Viaggio.
4. Make sure BOB
Stroller seat is in the
upright position. Refer
to BOB stroller
owner’s manual for
seat-recline strap(s)
location and function.
5. Rotate BOB stroller
canopy all the way
open, back against
the handlebar, Fig. 17.
6. Unbuckle Restraint
Belt. Move each belt
end outside the
stroller seat so they
will not be trapped
under the PEG
PEREGO, Fig. 17.
7. With car seat
handle in vertical
(carry) position, gently
place the PEG
PEREGO rear facing
in the seat of BOB
Stroller w/ICSA in a
straight downward
motion.
Restraint
Belt
Secured
Both Car Seat Grooves
Placed on Accessory Tube
Fig. 15 Graco Snug Ride Installed on
ICSA
Pull
Release
Handle
Hook
Retracted
For
Removal
Fig. 16 Graco Snug Ride Removal
Seat Upright
Canopy Against
Handlebar
8. Align the bottom
channels or grooves
of the PEG PEREGO
plastic frame so they
rest on the Accessory
Tube (Item 2) as
shown in Fig. 18.
9. Fasten buckle of
Restraint Belt over the
top of the PEG
PEREGO as shown in
Fig. 19.
10. Pull on the ring to
tighten the Restraint
Belt. When tightened
Both Car Seat Grooves
properly, the belt will
Placed on Accessory Tube
hold the PEG
PEREGO securely in
Fig. 18 Peg Perego Primo Viaggio
place.
Make sure the tension Placed on ICSA
of the belt is not
constricting your child.
Before use, verify you
have installed your
Primo Viaggio
correctly as shown in
Fig. 20.
As final double check
before use, attempt to
remove car seat with
the restraint belt. You
should not be able to
remove car seat
Restraint Belt
without unfastening
Routed Across
restraint belt.
Car Seat
And Buckled
To remove the PEG Fig. 19 Peg Perego Primo Viaggio
Secured With Restraint Belt
PEREGO:
1. Set parking brake.
2. Unbuckle the ICSA
Handle in
Canopy Against
restraint belt and
Upright
Handlebar
move out of way.
Position
3. Lift the PEG
PEREGO straight up
and off the BOB
stroller with the handle
of the PEG PEREGO
in the vertical (carry)
position.
Seat
4. Fasten restraint belt
Upright
when not in use to
prevent damage.
Restraint
Belt
Both Car Seat Grooves
Secured
Placed on Accessory Tube
Fig. 20 Peg Perego Primo Viaggio
Installed on ICSA
Restraint
Belt
Outside
Stroller
Accessory
Tube
Fig. 17 Correct Configuration for Peg
Pergeo Primo Viaggio
LIMITED WARRANTY
BOB Trailers Inc. takes pride in its workmanship and strives to
manufacture the best products possible. Therefore, we warranty the
ICSA against defects in material and workmanship subject to the
conditions listed below. Since no product is indestructible, it does not
cover defects attributable to or resulting from normal wear, abuse or
alteration.
. The ICSA is warranted for one year from the date of original
purchase.
. Warranty is only valid for the original purchaser.
. Proof of purchase is required to exercise this warranty.
. Labor and freight charges are not included.
. Normal wear, neglect, abuse, accidents, and improper use are not
covered by this warranty.
. Warranty claims must be made through an authorized dealer.
. This warranty is limited to the repair or replacement of the defective
part. BOB Trailers, Inc. shall in no event be responsible for
consequential or special damages.
. This Limited Warranty is the only express or implied warranty
applicable to BOB Trailers, Inc. Any implied warranties, including
warranties of merchantability and fitness shall be limited in scope
and duration in accordance with this limited warranty.
BŸOŸB, BŸOŸB Logo, and BOB are proprietary trademarks of BOB
Trailers, Inc.
Britax® and Companion® are registered trademarks of Britax Excelsior
Ltd. and related companies
Graco® and Snug Ride® are registered trademarks of Graco Children’s
Products, Inc.
Peg Perego® and Primo Viaggio™ are registered and proprietary
trademarks of Peg Perego S.P.A. Corporation
Download PDF