Carrier | AQUAZONE 50VQL080-300 | Product data | Carrier AQUAZONE 50VQL080-300 Product data

Product
Data
AQUAZONE™
50VQP084-300
Vertical Large Capacity
Water Source Heat Pumps
with PURON® Refrigerant (R-410A)
7 to 25 Nominal Tons
TM
Single-package vertically mounted
water source heat pumps (WSHPs)
with electronic controls.
• Non-ozone depleting Puron
refrigerant (R-410A)
• Performance certified to ARI/ISO/
ASHRAE 13256-1
• Wide application use with operating
temperature range of 20 F to 110 F
• Dual refrigerant circuits for 2-stage
operation
• High-efficiency scroll compressors
• Thermostatic expansion valve (TXV)
provides efficient and reliable
refrigerant flow
• High-static capability available
• Available mute package for quiet
operation
• Available low temperature insulation
to prevent condensation
• Easy service access
• Flexible and reliable multiple
protocol WSHP Open controller can
use BACnet*, Modbus†, N2, and
LON** (with separate card)
protocols for integrating energy
efficiency and precise unit control
Features/Benefits
Carrier’s Aquazone™ large
capacity units offer low cost,
energy efficient solutions for
all challenging water source
heat pump applications.
Operating efficiency
Carrier’s Aquazone large capacity
vertical water source heat pumps are
designed for quality and high performance over a lifetime of operation.
Aquazone units offer cooling EERs
(Energy Efficiency Ratio) to 21.4 and
heating COPs (Coefficient of Performance) to 5.1.
Copyright 2009 Carrier Corporation
Form 50VQP-1PD
Features/Benefits (cont)
Efficiencies stated are in accordance
with standard conditions under ISO
(International Organization for Standardization) Standard 13256-1 and provide among the highest ratings in the
industry, exceeding ASHRAE (American Society of Heating, Refrigerant and
Air Conditioning Engineers) 90.1
Energy Standards.
High quality construction and
testing
All units are manufactured to meet
extensive quality control protocol from
start to finish through an automated
control system, which provides continuous monitoring of each unit and
performs quality control checks as
equipment progresses through the
production process. Standard construction features of the Aquazone™ units
include:
Cabinet — Standard unit fabrication
consists of heavy gage galvanized sheet
metal cabinet construction that provides
maximum strength. Cabinet interior
surfaces are lined with 1/2 in. thick,
11/2 lb acoustic type insulation. Sheet
metal surfaces are treated for maximum corrosion protection to ensure
resilience for long term vitality. The
condensate pan is coated with bakedon enamel finish and insulated.
Compressor — Aquazone large
capacity units include dual high capacity scroll compressors. Compressor isolating springs are specially selected for
each compressor size. The external
isolation springs are mounted on an
isolated railing system to minimize
vibrations to the unit structure.
Blower and motor assembly —
Belt driven centrifugal blowers are provided with all units to satisfy many air
distribution applications. Optional
motor speeds and sizes are available to
provide high static capability. Aquazone
blower motors are designed to operate
at lower temperatures to help improve
the reliability of the WSHP.
Refrigeration/water circuit — Units
have a sealed refrigerant circuit including a scroll compressor. Refrigerant
circuits are provided with a standard
thermostatic expansion valve (TXV) for
higher accuracy and performance. Also
standard are a reversing valve (4-way
valve), water-to-refrigerant coaxial
(tube-in-tube) coil, and enhanced aluminum fin/rifled copper tube air-to-refrigerant heat exchanger coil.
ARI/ISO — Carrier’s Aquazone units
have ARI (Air Conditioning & Refrigeration Institute)/ISO, NRTL (Nationally
Recognized Testing Lab), or ETL labels
and are factory tested under normal
operating conditions at nominal water
flow rates. Quality assurance is provided via testing report cards shipped
with each unit to indicate specific unit
performance under cooling and heating modes of operation.
Puron® refrigerant (R-410A)
Puron refrigerant (R-410A) is a nonchlorine based refrigerant. Puron refrigerant characteristics, compared to
R-22, have:
• Binary and near azeotropic mixture
of 50% R-32 and 50% R-125.
• Higher efficiencies (50 to 60%
higher operating pressures).
• Non-ozone depleting potential and
low global warming potential.
• Virtually no glide. Unlike other alternative refrigerants, the two components in Puron refrigerant have
virtually the same leak rates. Therefore, refrigerant can be added if necessary without recovering the
charge.
Quiet operation
Fan motor insulation and compressor
springs are provided for sound
Table of contents
Features/Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Model Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ARI/ISO Capacity Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Physical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Options and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10,11
Selection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12,13
Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-35
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36,37
Typical Piping and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Typical Control Wiring Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . .39-45
Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46-50
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51-54
Guide Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55-58
2
isolation, cabinets are fully insulated to
reduce noise transmission, low speed
blowers are utilized for quiet operation
through reduced outlet air velocities,
and air-to-refrigerant coils are designed
for lower airflow coil face velocities.
Design flexibility
Aquazone vertical units are available in
four airflow patterns including top or
front discharge with right or left return.
Extended water temperature range
between 20 F and 110 F offers
maximum design flexibility for all applications. Water flow rates as low as
1.5 gpm per ton assist with selection
from a various range of circulating
pumps. Factory-installed options
are offered to meet specific design
requirements.
Safe, reliable operation
Standard safety features for the refrigerant circuit include high-pressure
switch and low-pressure sensor to
detect loss of refrigerant. A low air
temperature sensor safeguards against
freezing. Equipment safety features
include water loop temperature monitoring, voltage protection, water coil
freeze protection, and standard electronic condensate overflow shutdown.
All Aquazone safety features are tested
at the factory to assure proper operation of all components and safety
switches.
All components are carefully designed and selected for endurance,
durability, and carefree day-to-day
operation.
The Aquazone unit is shipped to
provide internal and external equipment protection. Shipping supports
are placed under the blower housing
and compressor feet. In addition, units
are mounted on oversized pallets with
lag bolts for sturdiness and maximum
protection during transit.
Ease of installation
The Aquazone™ unit is packaged for
simple low cost handling, with minimal
time required for installation. All units
are pre-wired and factory charged with
refrigerant. Water connections (FPT)
and condensate drains (FPT) are
anchored securely to the unit cabinet.
High and low voltage knockouts are
provided on all units.
Simple maintenance and
serviceability
The Aquazone WSHP units are constructed to provide ease of maintenance. Units have large removable
panels for easy access. Additional panels are provided to access the blower
and control box sections.
The blower housing assembly can be
serviced without disconnecting ductwork from the dedicated blower access
panel. Blower units are provided with
permanently lubricated bearings for
worry-free performance.
Electrical disconnection of the
blower motor and control box is easily
accomplished from quick disconnects
on each component.
Easy removal of the control box
from the unit provides access to all
refrigeration components.
The refrigeration circuit is easily
tested and serviced through the use of
high and low pressure ports integral to
the refrigeration circuit.
Maximum control flexibility
Aquazone water source heat pumps
provide reliable control operation using
a standard microprocessor board with
flexible alternatives for many direct digital control (DDC) applications including the Carrier Comfort Network®
(CCN) and open protocol systems.
Carrier’s Aquazone standard unit
solid-state control system, the Complete C, provides control of the unit
compressor, reversing valve, fan, safety
features, and troubleshooting fault indication features. The Complete C control system is one of the most user
friendly, low cost, and advanced
control boards found in the WSHP
industry. Many features are field selectable to provide the ultimate in field
installation flexibility. The overall
features of this standard control system
include:
75-va transformer assists in accommodating accessory loads.
Anti-short cycle timer provides a
minimum off time to prevent the unit
from short cycling. The 5-minute timer
energizes when the compressor is
deenergized, resulting in a 5-minute
delay before the unit can be restarted.
Random start relay ensures a random delay in energizing each different
WSHP unit. This option minimizes
peak electrical demand during start-up
from different operating modes or after
building power outages.
High and low pressure refrigerant
protection safeguards against unreliable unit operation and prevents refrigerant from leaking.
Condensate overflow sensor,
mounted to the drain pan, recognizes
thirty continuous seconds of condensate pan overflow as a fault. When
condensate pan liquid reaches an unacceptable level, unit is automatically
deactivated and placed in a lockout
condition.
High and low voltage protection
safe guards against excessive or low
voltage conditions.
Automatic intelligent reset automatically restarts unit 5 minutes after
shutdown if the fault has cleared.
Should a fault occur 3 times sequentially, lockout will occur.
Accessory output (24-v) is provided
to cycle a motorized water valve or
damper actuator with compressor in
applications such as variable speed
pumping arrangements.
Performance Monitor (PM) feature
monitors water temperatures to warn
when the heat pump is operating inefficiently or beyond typical operating
range. Field selectable switch initiates a
warning code on the unit display.
Water coil freeze protection
(selectable for water or antifreeze) field selectable switch for water
and water/glycol solution systems initiates a fault when temperatures
exceed the selected limit for 30 continuous seconds.
Air coil freeze protection (check
filter operation) field selectable
switch for assessing excessive filter
pressure drop initiates a fault when
temperatures exceed the selected limit
for 30 continuous seconds.
Alarm relay setting is a selectable
24-v or pilot duty dry contact for providing activation of a remote alarm.
Electric heat option output provided on the controller for operating
two stages of emergency electric heat.
Service test mode with diagnostic
LED (Light-emitting diode) allows
service personnel to check the operation of the WSHP and control system
efficiently. Upon entering Test mode,
time delays are sped up, and the Status
LED will flash a code to indicate the
last fault experienced for easy diagnosis. Based on the fault code flashed by
the status LED, system diagnostics are
assisted through the use of Carrier provided troubleshooting tables for easy
reference to typical problems.
LED visual output indicates high
pressure, low pressure, low voltage,
high voltage, air/water freeze protection, condensate overflow, and control
status on an LED panel.
Open protocol for diverse control
(LON controller) option is ideal
when building automation requires
interoperability across diverse control
platforms. This LONMark** compliant
offering can operate as standalone or
as a part of Local Operating Network
(LON) via the LONWORKS** FTT-10
Free Topology communication network.
Factory completed, pre-engineered
applications specific to Aquazone
water source heat pumps and digital
wall sensors communicating over Sensor Link (S-Link) communication protocol completes a system of networked
control.
Humidity control on Aquazone
50VQP units enables the units to provide very good latent capacity making
them an excellent choice for controlling humidity within a zone in many
applications. The latent capacity of the
units can be increased based on zone
conditions with either the use of fan
speed control and a humidistat. The
Deluxe D controls option provides fan
speed control based on relative humidity and is an effective, low-cost means
of controlling humidity.
WSHP Open multiple protocol
controller — Carrier's state of the art
water source heat pump multiple
protocol controller is capable of
communicating BACnet, Modbus, N2,
and LON (with separate card) protocols. The controller is designed specifically for Carrier's WSHPs in order to
bring more features and benefits to the
units such as water-side economizer
control, auxiliary heat, dehumidification, etc., in addition to independent
compressor and fan operation. The
WSHP Open controller can be used to
actively monitor and control all modes
of operation as well as monitor the following diagnostics and features: unit
number, zone temperature, zone set
point, zone humidity set point, discharge air temperatures, fan status,
stages of heating, stages of cooling,
3
Features/Benefits (cont)
outdoor-air temperature, leaving-air
temperature, leaving water temperature, alarm status, and alarm lockout
condition.
The controller also provides a proactive approach to maintenance and
service enabling the unit to recognize
and correct operating conditions outside of recommended operating conditions avoiding the need to manually restart equipment. From a system standpoint WSHP Open controller can
accept both water and airside linkage.
Condenser water linkage provides
optimized water loop operation using
the UC (universal controller) Open XP
loop controller. Loop pump operation
is automatically controlled by WSHP
equipment occupancy schedules, unoccupied demand and tenant override
conditions. Positive pump status feedback prevents nuisance fault trips.
Airside linkage enables the WSHP
equipment to be completely integrated
with the Carrier's VVT® application as
a system. The WSHP Open controller
responds to individual zone demands
rather than average temperature conditions to provide individual temperature
control in each zone.
This controller has a 38.4 kilobaud
communications capability and is compatible with i-Vu® Open building automation system controls and CCN
controls. The addition of the Carrier
CO2 sensor in the conditioned space
provides ASHRAE 62-99 compliance
and demand controlled ventilation
(DCV). A DCV control strategy is especially beneficial for a water source heat
pump system to minimize the energy
utilized to condition ventilation air. In
combination with energy efficient
Aquazone units, DCV may be the most
energy efficient approach ever developed for a water source heat pump
system.
The WSHP Open multiple protocol
controller is designed specifically for
constant volume (CV) and variable
volume and temperature (VVT®) applications. This comprehensive controls
system allows water source heat pumps
to be linked together to create a fully
functional HVAC (heating, ventilation,
and air conditioning) automation
system.
PremierLink™ controller adds
reliability, efficiency, and
simplification
The PremierLink direct digital controller can be ordered as a factory-installed
option. Designed and manufactured
exclusively by Carrier, the controller
can be used to actively monitor and
control all modes of operation as well
as monitor the following diagnostics
and features: unit number, zone temperature, zone set point, zone humidity
*Sponsored by ASHRAE (American Society of Heating,
Refrigerant and Air Conditioning Engineers).
†Registered trademark of Schneider Electric.
**Registered trademark of Echelon Corporation.
4
set point, discharge air temperatures,
fan status, stages of heating, stages of
cooling, outdoor-air temperature, leaving-air temperature, leaving water temperature, alarm status, and alarm lockout condition.
This controller has a 38.4 kilobaud
communications capability and is
compatible with i-Vu® Open building
automation system controls and CCN
controls. The addition of the Carrier
CO2 sensor in the conditioned space
provides ASHRAE 62-99 compliance
and demand controlled ventilation
(DCV). A DCV control strategy is especially beneficial for a water source heat
pump system to minimize the energy
utilized to condition ventilation air. In
combination with energy efficient
Aquazone units, DCV may be the most
energy efficient approach ever developed for a water source heat pump
system.
The PremierLink peer-to-peer, Internet ready communicating control is designed specifically for constant volume
(CV) and variable volume and temperature (VVT®) applications. This comprehensive controls system allows water source heat pumps to be linked together to create a fully functional
HVAC (heating, ventilation, and air
conditioning) automation system.
Model number nomenclature
50VQP
180
B
C
C
5
0
1
A
1
50VQP - Vertical Large Capacity
Water Source Heat Pump
with Puron® Refrigerant (R-410A)
Operating Range and Sound Options
1 - Extended Range (20 to 110 F)
2 - Extended Range and Mute Package
3 - Standard Range (60 to 95 F)
4 - Standard Range and Mute Package
Nominal Capacity - Tons
084 - 7
192 - 16
096 - 8
240 - 20
120 - 10
300 - 25
150 - 12 1/2
168 - 14
Blower Drive Options
A - Standard rpm/Standard Motor
B - Low rpm/Standard Motor
C - High rpm/Standard Motor
D- Standard rpm/Large Motor*
E- High rpm/Large Motor
Airflow Configuration
Return Discharge
B - Rear
Top
F - Front
Top
S - Rear
Front
Z - Front
Rear
Packaging
1 - Domestic
Revision
0 - Current Revision
Controls
C - Complete C Microprocessor Control
D - Deluxe D Microprocessor Control
L - Complete C with LON
M - Deluxe D with LON
P - Complete C with PremierLink™ Communicating Control
W - Complete C with WSHP Open Multiple Protocol Communicating Control
Y - Deluxe D with WSHP Open Multiple Protocol Communicating Control
Voltage
1 - 575-3-60
5 - 280/230-3-60
6 - 460-3-60
LEGEND
LON — LonWorks Interface System
*Not available for unit size 240.
NOTES:
1. Standard cabinet is powder-painted.
2. 208/230 volt unit is wired for 208 volts, but can be field
converted to 230 volts.
3. 1-in. return filter included.
4. 75-VA standard transformer included.
Heat Exchanger Options
A - Coated, Copper
C - Non-Coated, Copper
J - Coated, Cupronickel
N - Non-Coated, Cupronickel
A50-8435
ARI/ISO capacity ratings
50VQP UNIT CAPACITY RATINGS
50VQP
UNIT SIZE
084
096
120
150
168
192
240
300
COP
db
EER
wb
—
—
—
—
WATER LOOP HEAT PUMP
Cooling 86 F
Heating 68 F
Capacity
EER
Capacity
COP
Btuh
Btuh/W
Btuh
82,000
15.2
101,000
4.8
94,000
15.0
118,000
4.7
118,000
15.0
144,000
5.0
150,000
14.0
186,000
4.7
166,000
15.5
204,020
4.9
190,000
15.3
238,360
4.8
238,500
15.3
291,000
5.1
300,000
14.0
372,000
4.7
LEGEND
Coefficient of Performance
Dry Bulb
Energy Efficiency Ratio
Wet Bulb
GROUND WATER HEAT PUMP
Cooling 59 F
Heating 50 F
Capacity
EER
Capacity
COP
Btuh
Btuh/W
Btuh
87,500
21.0
83,500
4.3
102,500
20.5
96,500
4.2
133,000
21.0
118,000
4.2
170,000
20.0
155,000
4.2
177,000
21.4
169,000
4.4
207,000
20.9
195,000
4.3
269,000
21.4
238,500
4.3
340,000
20.0
310,000
4.2
GROUND LOOP HEAT PUMP
Cooling 77 F
Heating 32 F
Capacity
EER
Capacity
COP
Btuh
Btuh/W
Btuh
83,000
16.5
65,500
3.6
97,500
16.5
76,500
3.6
120,000
16.5
93,000
3.7
156,000
15.8
122,000
3.6
168,000
16.8
132,500
3.7
197,000
16.8
155,000
3.7
242,500
16.8
188,000
3.8
312,000
15.8
244,000
3.6
NOTES:
1. Cooling capacities based upon 80.6 F db, 66.2 F wb entering air
temperature.
2. Heating capacities based upon 68 F db, 59 F wb
entering air temperature.
3. All ratings based upon operation at lower voltage
of dual voltage rated models.
5
Physical data
50VQP UNIT PHYSICAL DATA
50VQP UNIT SIZE
NOMINAL AIRFLOW (cfm)
WEIGHT (lb)
Operating
Packaged
COMPRESSOR (qty)
REFRIGERANT
Charge (oz per circuit)
BLOWER MOTOR (Qty)
Standard Motor (hp)
Large Motor (hp)
BLOWER (qty)
Wheel Size (Depth x Width, in.)
WATER CONNECTION SIZE (in., FPT)
COAX VOLUME (gal)
CONDENSATE CONNECTION SIZE (in., FPT)
AIR COIL
Height x Width (in.) (Qty)
Total Face Area (sq ft)
Tube Size (in.)
Fin Spacing (FPI)
Number of Rows
FILTER, THROWAWAY (in.)(qty)
084
2,800
096
3,200
650
665
696
711
Scroll (1)
6
150
5,000
168
5,600
700
715
192
6,400
1300
1330
240
8,000
1346
1376
Scroll (2)
300
10,000
1404
1434
R-410A
140
156
224
248
140
156
224
248
2
3
3
5
5
7.5
5
7.5
6.36
15 x 15
2 1 /2
7.39
1
1
1.5
1.5
2
2
3
3
5
1
2
15 x 11
1 1 /2
2.19
15 x 15
2.48
15 x 11
2
4.83
3.46
1
36 x 48 (1)
12
36 x 48 (2)
24
3/
14
2
3
18 x 25 (4)
LEGEND
FPI — Fins per Inch
FPT — Female Pipe Thread
NOTES:
1. All units have grommet and spring compressor mountings, and
1/2 in. and 13/4 in. electrical knockouts.
2. Use the lowest maximum pressure rating when multiple options
are combined:
OPTION
Base Unit
Motorized Water Valve
Internal Secondary Pump
120
4,000
MAXIMUM PRESSURE (psig)
450
400
145
12
4
8
14
2
3
18 x 25 (8)
12
4
Options and accessories
DESCRIPTION
Cupronickel Heat Exchangers
Sound Attenuation Package (Mute Package)
Extended Range
High-Static Blower Drive Options
Deluxe D Control System
WSHP Open Multiple Protocol Controller
PremierLink™ Controller
LONMark Compliant Controller
Aquazone™ Thermostats
Filters
Filter Rack
Fire-Rated Hoses
Ball Valves
Y Strainers
Solenoid Valves
Hose Kit Assemblies
Remote Sensors (SPT, CO2, Humidity Sensors)
UC Open XP Loop Controller
PremierLink Accessories
FACTORY-INSTALLED OPTION
X
X
X
X
X
X
X
X
Factory-installed options
Cupronickel heat exchangers are available for higher
corrosion protection for applications such as open tower,
geothermal, etc. Consult the water quality guidelines for
proper application and selection of this option.
Sound attenuation package (mute package) is available for applications that require especially low noise levels. With this option, a double application of sound
attenuating material is applied, access panels are double
dampened with 1/2-in. thick density fiberglass insulation,
and a unique application of special dampening material is
applied to the curved portion of the blower. The mute
package in combination with standard unit noise reduction
features (i.e., as mentioned previously) provides sound levels and noise reduction to the highest degree.
Extended range units provide an insulated water circuit
for the coaxial coil and refrigerant circuit to prevent condensation, and therefore potential dripping problems, in
applications where the entering water temperature is
beyond the normal operating range (less than 60 F).
High-static blower drive options provide maximum
flexibility for the most challenging applications. Three
static range motors are available in low, standard, and high
rpm configurations. An optional large motor arrangement
is available for high-static designs.
Deluxe D control system provides the same functions
as the Complete C control system while incorporating
additional flexibility and functions to include:
Thermostat input capabilities accommodate emergency
shutdown mode and night setback with override (NSB)
potential. Night setback from low temperature thermostat
with 2-hour override is initiated by a momentary signal
from the thermostat.
Compressor relay staging is used with dual stage units
(units with 2 compressors and 2 Deluxe D controls) or in
master/slave applications.
Boilerless electric heat control system allows automatic
changeover to electric heat at low loop water temperature.
X
X
FIELD-INSTALLED ACCESSORY
X
X
X
X
X
X
X
X
X
X
X
Intelligent reversing valve operation minimizes reversing
valve operation for extended life and quiet operation.
Thermostat type select (Y, O or Y, W) provides ability to
work and select heat pump or heat/cool thermostats (Y, W).
Reversing valve signal select (O or B) provides selection for
heat pump O/B thermostats.
Multiple units on one thermostat/wall sensor provide
communication for up to three heat pumps on one
thermostat.
Boilerless changeover temperature provides selection of
boilerless changeover temperature set point.
Accessory relays allow configuration for multiple applications including fan and compressor cycling, digital night
setback (NSB), mechanical night setback, water valve operation, and outside air damper operation.
WSHP Open multiple protocol controller is a
proactive controller capable of communicating BACnet,
Modbus, N2, and LON (with separate card) protocols. The
controller is designed to allow users the access and ability
to change and configure multiple settings and features
including indoor air quality (IAQ), waterside economizer
controls, etc.
PremierLink™ controller is compatible with the Carrier
Comfort Network® (CCN) and other building automation
systems (BAS). This control is designed to allow users the
access and ability to change factory-defined settings, thus
expanding the function of the standard unit.
LONMark compliant controller contains the factoryloaded Aquazone water source heat pump application for
an interoperable control solution.
Filters are available in 2 in. or 4 in. (MERV 8) sizes.
Filter rack is available to accomodate one, 2, or 4 in. filters in place of the standard 1-in. return air filter to
enhance the filtration system of the water source heat
pump. The filter rack does not include filters.
7
Options and accessories (cont)
Field-installed accessories
Carrier’s line of Aquazone™ thermostats are both
attractive and multi-functional, accommodating standalone water source heat pump installations.
Programmable 7-day thermostat offers 2-stage heat, 2stage cool, auto changeover, 7-day programmable with
copy command, 4 settings per day, fully electronic, 24 vac,
backlit LCD, keypad lockout, no batteries required,
5-minute compressor protection, NEVERLOST™ memory,
3 security levels, and temperature display in degrees F or C.
Programmable 7-day light-activated thermostat offers the
same features as the 7-day programmable thermostat and
includes occupied comfort settings with lights on, unoccupied energy savings with lights off.
Programmable 7-day flush-mount thermostat offers the
same features as the 7-day programmable thermostat and
includes locking coverplate with tamper proof screws, flush
to wall mount, holiday/vacation programming, set point
limiting, dual point with adjustable deadband, O or B terminal, and optional wall or duct-mounted remote sensor.
Programmable 5-day thermostat offers 2-stage heat,
2-stage cool, auto changeover, 5-minute built-in compressor protection, locking cover included, temperature display
in degrees F or C, keypad lockout, backlit display, 5-1-1
programming, O or B terminal, dual set point with adjustable deadband, configurable display, self-prompting program, and 4 settings per day.
Non-programmable thermostat offers 2 heat stages, 2 cool
stages, auto changeover, 5-minute built in compressor protection, locking cover included, temperature display in
degrees F or C, keypad lockout, large display, backlit display, O or B terminal, dual set point with adjustable deadband, and backplate with terminals.
Filters are available in 2 in. or 4 in. (MERV 8) sizes.
Filter rack is available to accomodate one, 2, or 4 in. filters in place of the standard 1-in. return air filter to
enhance the filtration system of the water source heat
pump. The filter rack does not include filters.
Fire-rated hoses are 2 ft long and have a fixed MPT on
one end and a swivel with an adapter on the other end.
Hose kits are provided with both a supply and return hose
and can be either stainless steel or galvanized. Five sizes
are available (1/2, 3/4, 1, 11/4, 11/2 in.).
Ball valves (brass body) are used for shutoff and
balancing water flow and are available with memory,
memory stop, and pressure temperature ports. Valves
consist of UL-listed brass body, ball and stem type with
Teflon* seats and seals. Five sizes are available (1/2, 3/4, 1,
11/4, 11/2 in.).
Y strainers (bronze body) are “Y” type strainers with a
brass cap. With a maximum operating pressure rating of
450 psig, the strainer screen is made of stainless steel.
*Teflon is a trademark of E. I. du Pont de Nemours and Company.
8
Strainers are available with blow down valves. Five sizes
are available (1/2, 3/4, 1, 11/4, 11/2 in.).
Solenoid valves (brass body) offer 3.5 watt coil,
24 volt, 50/60 Hz, 740 amps inrush, and .312 amp holding. Valves operate slowly for quiet system application.
Five sizes are available (1/2, 3/4, 1, 11/4, 11/2 in.).
Hose kit assemblies provide all the necessary components to hook up a water-side system. Supply hose
includes a ported ball valve with pressure temperature (P/
T) plug ports, flexible stainless steel hose with swivel and
nipple. Return hose includes a ball valve, preset automatic
balancing valve (gpm) with two P/T ports, flexible stainless
steel hose with a swivel and nipple, balancing valve, and
low-pressure drop water control valve.
Remote sensors are available for Aquazone flush-mount
thermostats and for wall (wired and wireless) or duct
mounted applications.
SPT Standard offers space temperature sensor with communication port.
SPT Plus offers space temperature sensor with set point
adjust, local override with indicating light and communication port.
SPT Pro offers space temperature sensor with LCD display, set point adjust, local override, alarm icon, outside
air, and unit status with heating and cooling set points.
SPT Pro+ offers space temperature sensor with LCD display, set point adjust, local override, alarm icon, outside
air, unit status with heating and cooling set points, and fan
speed control.
LON wall sensors are available in 3 models: sensor only,
sensor with status override indicator, and sensor with set
point, status adjustment override, and digital LCD display.
UC Open XP loop controller with six stages (2 stages
for heating and 4 stages for cooling) includes:
• Loop temperature alarms
• Two pump single loop flow monitoring with the ability
to manually select the lead pump
• One common alarm signal and indicating light and one
audible alarm
• Loop water temperature sensor test circuit
• Functional test simulation from operator keypad
• Real timeclock, industrial noise ratings
• Loop water temperature control switch
• Loop controller with six stages (2 stages for heating and
4 stages for cooling)
PremierLink™ accessories are available for providing a
fully integrated WSHP DDC system. Accessories include
supply air temperature sensors (with override and/or setpoint adjustment), communicating room sensors, CO2 sensors (for use in demand control ventilation), and linkage
thermostats (to control multiple units from one thermostat).
AQUAZONE™ THERMOSTATS
Carrier
®
R
Pm
COOL
AUTO
COOL
HEAT
AUTO
HEAT
7-DAY PROGRAMMABLE/
LIGHT-ACTIVATED PROGRAMMABLE
5-DAY PROGRAMMABLE/
NON-PROGRAMMABLE
7-DAY PROGRAMMABLE
FLUSH MOUNT
WSHP OPEN SENSORS
a33WARMER
MANUAL ON
WARMER
INFO
COOLER
MANUAL ON
WARMER
INFO
COOLER
MODE
FAN SPEED
a33a33-
COOLER
a33-
SPACE TEMPERATURE
SENSOR WITH SET
POINT ADJUSTMENT
AND LOCAL OVERRIDE
OCCUPIED
MANUAL
ON
SPACE TEMPERATURE
SENSOR WITH SLIDE SET
POINT ADJUSTMENT AND
LOCAL OVERRIDE
SPACE TEMPERATURE
SENSOR WITH SET
POINT ADJUSTMENT,
FAN SPEED CONTROL,
AND LOCAL OVERRIDE
SPACE TEMPERATURE
SENSOR ONLY
LON WALL SENSORS
SENSOR ONLY
SENSOR WITH OVERRIDE
SENSOR WITH SET POINT ADJUSTMENT,
OVERRIDE AND DIGITAL LCD
9
Dimensions
50VQP084-150 UNITS
ALL CONFIGURATIONS REQUIRE SERVICE ACCESS AREA SHOWN BELOW
7.6
F
D
B
7.6
F
NRP
AIR OUT
AIR OUT
NRP
BSP
T
a50-8436
BSP
NRP
RETURN AIR
RETURN AIR
S
C
4
1
Q
4
NRP
3
Control Box
CAP+MSP
O2
NRP
2
5
U
R
Control Box
4
3
3
P
N
O1
4
2
NRP
MK
L
M
K
CSP+CAP+MSP
L
CSP
3
5
1
A
FRONT RETURN TOP DISCHARGE
REAR RETURN TOP DISCHARGE
F
1.7
F
BSP
D
AIR OUT
RETURN AIR
BSP
E
BSP
AIR OUT
NRP
RETURN AIR
4
1
5
4
NRP
4
NRP
2
5
NRP
3
4
Control Box
CAP+MSP
Control Box
3
2
4
4
3
4
4
5
3
5
1
NRP
CSP+CAP+MSP
CSP
SIDE
SERVICE ACCESS
(SEE NOTE 10)
SERVICE ACCESS
3’ (91 CM)
FRONT AND BACK
FRONT RETURN REAR DISCHARGE
REAR RETURN FRONT DISCHARGE
BSP
CAP
CSP
MSP
NRP
—
—
—
—
—
CONNECTIONS
LEGEND
Blower Service Panel
Control Access Panel
Compressor Service Panel
Motor Service Panel
Non-Removable Panel
50VQP084-120
50VQP150
Water Inlet (See Note 7)
11/2 in. FPT
2 in. FPT
2
Water Outlet (See Note 7)
1 1/
2 in. FPT
3
Condensate Drain (See Note 8)
4
High Voltage Access (See Note 9)
1
2
in. FPT
1 in. FPT
1 in. FPT
13/8 in.
13/8 in.
NOTES:
1. All dimensions in inches.
7/8 in.
5 Low Voltage Access (See Note 9)
2. Units require 3 ft clearance for water connections, CAP, CSP, MSP, and BSP service access.
3. Overall cabinet height dimension does not include duct flange when in top discharge configuration.
4. Overall cabinet width dimension does not include filter rack and duct flange when on front or back discharge configuration.
5. Side service access must be 3 ft on either side that connections are made. If no connections are made on a side, then service access can be 6 in. minimum.
6. While access to all removable panels is not required, installer should take care to comply with all building codes and allow adequate clearance for future field service.
7. Water inlet and water outlet connections are available on either side (left or right) of the unit. Two MPT plugs are shipped loose in a plastic bag tied to the water leg in
front of the unit. Installer must plug water inlet/outlet side not being connected to.
8. Condensate drain is available on either side (left or right) of unit. Drain hose and drain connection will be tied inside the unit. Installer must untie the drain hose and
connect to the condensate drain hole of installer’s choice.
9. Electrical access is available on either side (left or right) of unit and is also available (left or right) in the front of the unit.
10. All configurations require service access area shown in the rear return front discharge figure above.
UNIT
50VQP
OVERALL
CABINET (in.)
DISCHARGE
CONNECTIONS (in.)
Duct Flange
D
E
Supply
Supply
F
Width
Depth
A
Depth
B
Width
C
Height
084-120
34.0
53.1
79.0
17.5
17.6
150
34.0
53.1
79.0
21.4
17.6
10
WATER
CONNECTIONS (in.)
ELECTRICAL
KNOCKOUTS (in.)
7/8
in.
RETURN AIR
CONNECTIONS (in.)
(Using Return Air Opening)
S
T
Return Return
U
V
Depth
Height
K
1-Water
Inlet
L
1-Water
Outlet
M
3Condensate
N
O1
O2
P
Q
R
17.8
31.0
3.0
27.0
25.6
31.0
38.0
34.6
1.0
3.0
48.0
32.4
44.6
2.7
17.8
31.0
3.0
27.0
25.6
31.0
38.0
34.6
1.0
3.0
48.0
32.4
44.6
2.7
50VQP168-300 UNITS
ALL CONFIGURATIONS REQUIRE SERVICE ACCESS
V
7.6
F
D
7.6
G
B
D
AIR OUT
AIR OUT
E
C
NRP
NRP
F
AIR OUT
NRP
RETURN AIR
AIR OUT
E
T
BSP
BSP
RETURN AIR
S
RETURN AIR
1
Q
S
5
3
MSP
O2
2
4
RETURN AIR
BSP
U
R
P
O1
3 Control Box
4
NRP
NRP
CAP
Control Box
4
CSP+CAP
2
1
3
CSP
5
4
N
M
NRP
NRP
CSP+MSP
M
CSP
L
3
L
K
K
A50-8437
A
REAR RETURN TOP DISCHARGE
FRONT RETURN TOP DISCHARGE
1.7
NRP
BSP
F
D
AIR OUT
G
E
F
BSP
D
AIR OUT
RETURN
AIR
AIR OUT
NRP
4
1
NRP
RETURN AIR
AIR OUT
RETURN
AIR
2
4
RETURN AIR
5
5
3
MSP
4
3 Control Box
4
CAP
NRP
NRP
Control Box
2
4
5
4
CSP
NRP
4
CSP+CAP
1
5
4
3
NRP
CSP+MSP
CSP
Service Access
3’ (91 cm)
Front and Back
(All Configurations)
3
Side Service Access
(See Note 10)
FRONT RETURN REAR DISCHARGE
REAR RETURN FRONT DISCHARGE
BSP
CAP
CSP
MSP
NRP
—
—
—
—
—
CONNECTIONS
LEGEND
Blower Service Panel
Control Access Panel
Compressor Service Panel
Motor Service Panel
Non-Removable Panel
50VQP168-240
50VQP300
1
Water Inlet (See Note 7)
2 in. FPT
21/2 in. FPT
2
Water Outlet (See Note 7)
2 in. FPT
21/2 in. FPT
3
Condensate Drain (See Note 8)
1 in. FPT
1 in. FPT
4
High Voltage Access (See Note 9)
13/8 in.
13/8 in.
NOTES:
1. All dimensions in inches.
7/ in.
5 Low Voltage Access (See Note 9)
8
2. Units require 3 ft clearance for water connections, CAP, CSP, MSP, and BSP service access.
3. Overall cabinet height dimension does not include duct flange when in top discharge configuration.
4. Overall cabinet width dimension does not include filter rack and duct flange when on front or back discharge configuration.
5. Side service access must be 3 ft on either side that connections are made. If no connections are made on a side, then service access can be 6 in. minimum.
6. While access to all removable panels is not required, installer should take care to comply with all building codes and allow adequate clearance for future field service.
7. Water inlet and water outlet connections are available on either side (left or right) of the unit. Two MPT plugs are shipped loose in a plastic bag tied to the water leg in
front of the unit. Installer must plug water inlet/outlet side not being connected to.
8. Condensate drain is available on either side (left or right) of unit. Drain hose and drain connection will be tied inside the unit. Installer must untie the drain hose and
connect to the condensate drain hole of installer’s choice.
9. Electrical access is available on either side (left or right) of unit and is also available (left or right) in the front of the unit.
10. All configurations require service access area shown in the rear return front discharge figure above.
UNIT
50VQP
OVERALL
CABINET (in.)
DISCHARGE
CONNECTIONS (in.)
Duct Flange
D
E
Supply
Supply
F
Width
Depth
A
Depth
B
Width
C
Height
168-240
34.0
106.7
79.0
17.5
17.6
300
34.0
106.7
79.0
21.4
17.6
WATER
CONNECTIONS (in.)
ELECTRICAL
KNOCKOUTS (in.)
7/
8
in.
RETURN AIR
CONNECTIONS (in.)
(Using Return Air Opening)
S
T
Return Return
U
V
Depth
Height
G
K
1-Water
Inlet
L
1-Water
Outlet
M
3Condensate
N
O1
O2
P
Q
R
17.8
31.3
31.0
3.0
27.0
25.6
31.0
38.0
34.6
1.0
3.0
48.0
32.4
44.6
2.7
17.8
23.4
31.0
3.0
27.0
25.6
31.0
38.0
34.6
1.0
3.0
48.0
32.4
44.6
2.7
11
Selection procedure (50VQP096 unit example)
I Determine the actual cooling and heating
loads at the desired dry bulb and wet bulb
conditions.
Assume cooling load at desired dry bulb 80 F and
wet bulb 65 F conditions are as follows:
Given:
Total Cooling (TC). . . . . . . . . . . . . . .95,100 Btuh
Sensible Cooling (SC) . . . . . . . . . . . .70,000 Btuh
Entering-Air Temperature db . . . . . . . . . . . . .80 F
Entering-Air Temperature wb . . . . . . . . . . . . .65 F
II Determine the following design parameters.
Entering water temperature, water flow rate (gpm),
airflow (cfm), water flow pressure drop and design
wet and dry bulb temperatures. Airflow cfm should
be between 300 and 450 cfm per ton. Unit water
pressure drop should be kept as close as possible
to each other to make water balancing easier. Enter
the appropriate Performance Data tables and
find the proper indicated water flow and water
temperature.
For example:
Entering Water Temp . . . . . . . . . . . . . . . . . .85 F
Water Flow . . . . . . . . . . . . . . . . . . . . . . 24 gpm
Airflow cfm . . . . . . . .2800 cfm (350 cfm per ton)
III Select a unit based on total cooling and total
sensible cooling conditions. Unit selected
should be closest to but not larger than the
actual cooling load.
Enter tables at the design water flow and water
temperature. Read the total and sensible cooling
capacities.
NOTE: Interpolation is permissible, extrapolation is
not.
For example:
Enter the 50VQP096 Performance Table at design
water flow and water temperature. Read Total
Cooling, Sensible Cooling and Heat of Rejection
capacities:
Total Cooling . . . . . . . . . . . . . . . . . .95,900 Btuh
Sensible Cooling . . . . . . . . . . . . . . . .68,800 Btuh
Heat of Rejection . . . . . . . . . . . . . .118,600 Btuh
NOTE: It is quite normal for water source heat
pumps to be selected on cooling capacity only since
the heating output is usually greater than the cooling
capacity.
IV Determine the correction factors associated
with the variable factors of dry bulb and wet
bulb using the Corrections Factor tables
found in this book.
12
Using the following formulas to determine the correction factors of dry bulb and wet bulb:
a) Corrected Total Cooling = tabulated total cooling
x wet bulb correction x airflow correction.
b) Corrected Sensible Cooling = tabulated sensible
cooling x wet/dry bulb correction x airflow
correction.
V Determine entering air and airflow correction
using the Corrections Factor tables found in
this book.
The nominal airflow for the 50VQP096 is
3200 cfm. The design parameter is 2800 cfm.
2800/3200 = 88% of nominal airflow:
Use the 88% row in the Airflow Correction Table.
Using the following formulas to determine the correction factors of entering air and airflow correction:
Table
Ent Air
Airflow
Corrected
Corrected Total = 95,900 x 0.975 x 0.982 = 91,819
Cooling
Corrected Sensi= 68,800 x 1.096 x 0.940 = 70,881
ble Cooling
Corrected Heat
= 118,600 x 0.979 x 0.980 = 113,787
of Rejection
Compare the corrected capacities to the load
requirements established in Step I. If the capacities
are within 10% of the load requirements, the equipment is acceptable. It is better to undersize than
oversize as undersizing improves humidity control,
reduces sound levels and extends the life of the
equipment.
VI Water temperature rise calculation and
assessment.
Calculate the water temperature rise and assess the
selection using the following calculation:
Correction of
Heat of Rejection
=
gpm x 500
For example, using the Corrected Heat of Rejection
from the last step:
Actual Temperature
Rise
113,787
= 9.5 F
24 x 500
If the units selected are not within 10% of the load
calculations, review what effect changing the gpm,
water temperature and/or airflow will have on the
corrected capacities. If the desired capacity cannot
be achieved, select the next larger or smaller unit
and repeat Steps I through VI.
Actual Temperature
Rise
=
VII ARI/ISO/ASHRAE 13256-1 Conversion
Performance standard ARI/ISO/ASHRAE 13256-1
became effective on January 1, 2000 and replaced
the existing ARI Standards 320 Water-Loop Heat
Pumps (WLHP), 325 Ground-Water Heat Pumps
(GWHP), and 330 Ground-Loop Heat Pumps
(GLHP).
The ARI/ISO Standard incorporates a consistent
rating methodology for including fan and pump
energy for calculating cooling capacity, heating
capacity, and energy efficiency ratios (EER). This
simplifies the use of rating data for heat pump performance modeling in seasonal energy analysis calculations, and allows for direct rating comparisons
across applications.
a) ISO Capacity and Efficiency Equations
The following equations are used to calculate and
correct cooling capacity, heating capacity, and respective EER:
ISO Cooling Capacity = (Cooling Capacity in
Btuh) + (Fan Power Correction in Watts x 3.412)
ISO Cooling EER = (ISO Cooling Capacity in
Btuh/3.412)/(Power Input in watts – fan power
correction in watts + pump power correction in
watts) = Watts/Watts
NOTE: Do not divide ISO Cooling Capacity by
3.412 to obtain Btuh/Watts.
ISO Heating Capacity = (Heating Capacity in
Btuh) – (Fan Power Correction in Watts x 3.412)
ISO Heating EER = (ISO Heating Capacity in
Btuh/3.412)/(Power Input in watts – fan power
correction in watts + pump power correction in
watts) = Watts/Watts
NOTE: Do not divide ISO Heating Capacity by
3.412 to obtain Btuh/Watts.
b) Identify the design conditions corrected for air and
water conditions.
Airflow cfm = 2800 cfm
Water Flow
(Based upon 12 F rise in temp) = 24 gpm
External Static Pressure = 0.4 in. wg
Water Pressure Drop = 20 ft of head
Power input = 6,600 watts
Cooling Capacity = 91,819 Btuh
c) Perform Fan Power Correction Adjustment
Use the following formula to calculate Fan Power
Correction:
Fan Power
Correction = (cfm x 0.472) x (External Static
Pressure x 249)/300 = Watts
= (2800 x 0.472) x (0.4 x 249)/300
= 439 Watts
d) Perform Pump Power Correction Adjustment
Use the following formula to calculate Pump Power Correction:
Pump Power
Correction
= (gpm x 0.0631) x (Pressure Drop
x 2,990)/300
= Watts
= (24 x 0.0631) x
(20 x 2,990)/300
= 302 Watts
e) Perform capacity and EER calculations
Use the following formula to calculate capacity
and EER:
ISO Cooling
Capacity
= (Cooling Capacity) + (Fan Power
Correction x 3.412)
= 91,819 + (439 x 3.412)
= 93,317 Btuh
f) Perform Corrections by using the ISO Equations
ISO EER = (ISO Cooling Capacity/3.412)/
(Power Input – Fan Power Correction + Pump Power Correction)
= Watts/Watts
NOTE: Do not divide ISO Cooling Capacity by
3.412 to obtain Btuh/Watts.
= (93,317/3.412)/(6,600 – 439 + 302)
= 4.23 Watts/Watt
= 14.4 Btuh/Watt
13
Performance data
50VQP084
2800 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
21.00
10.50
15.75
21.00
10.50
15.75
21.00
10.50
15.75
21.00
10.50
15.75
21.00
10.50
15.75
21.00
10.50
15.75
21.00
10.50
15.75
21.00
10.50
10.50
21.00
10.50
15.75
21.00
10.50
15.75
21.00
10.50
15.75
21.00
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
10.0
23.1
2.4
5.5
5.5
12.6
9.2
21.3
2.1
4.9
5.0
11.4
8.4
19.5
2.0
4.5
4.6
10.7
7.9
18.4
1.3
3.1
3.6
8.3
6.5
14.9
1.2
2.8
3.4
7.8
6.2
14.2
1.1
2.6
3.1
7.3
5.8
13.5
1.1
2.5
3.1
7.2
5.7
13.3
1.1
2.4
1.1
2.4
5.7
13.1
1.0
2.3
2.9
6.8
5.5
12.8
0.9
2.1
2.8
6.5
5.4
12.4
0.9
2.0
2.7
6.3
5.2
12.1
TC
81.7
77.1
74.5
86.4
84.0
82.3
88.0
87.3
86.5
87.0
87.6
87.6
84.8
86.4
87.0
81.9
84.2
85.2
79.9
82.3
83.4
77.8
80.5
81.7
73.5
76.2
77.6
69.2
71.8
73.2
65.3
67.6
68.8
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
Operation Not Recommended
57.1
3.8
94.7
53.5
3.5
89.1
51.5
3.4
86.0
61.0
4.3
101.1
58.8
4.0
97.6
57.5
3.9
95.5
62.8
4.7
104.1
61.8
4.4
102.4
61.1
4.3
101.2
62.8
5.1
104.5
62.7
4.8
104.1
62.4
4.7
103.7
62.2
5.6
103.8
62.7
5.3
104.4
62.8
5.1
104.5
61.0
6.1
102.6
61.9
5.7
103.7
62.3
5.6
104.2
60.1
6.3
101.5
61.1
6.0
102.8
61.5
5.8
103.3
59.3
6.6
100.3
60.4
6.2
101.8
60.9
6.1
102.4
57.5
7.2
98.2
58.6
6.8
99.5
59.2
6.6
100.2
55.8
8.0
96.4
56.8
7.5
97.4
57.4
7.3
98.0
54.6
8.8
95.5
55.3
8.3
95.9
55.7
8.0
96.3
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP084 UNIT
(Cv = 37, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
10.50
0.08
0.2
15.75
0.18
0.4
21.00
0.32
0.7
14
EER
21.4
22.0
22.1
20.2
21.0
21.3
18.7
19.7
20.1
17.0
18.1
18.6
15.2
16.4
17.0
13.5
14.7
15.3
12.7
13.8
14.4
11.8
12.9
13.5
10.2
11.2
11.7
8.7
9.6
10.1
7.4
8.1
8.6
HC
58.0
63.2
65.8
67.3
72.6
76.0
77.9
82.7
87.0
89.4
93.3
98.2
100.9
103.7
109.2
112.1
113.8
119.4
122.2
118.4
123.8
126.5
123.0
128.2
130.7
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
5.3
39.7
86.7
5.5
44.5
89.9
5.6
46.9
90.8
5.6
48.2
91.2
5.7
53.0
93.2
5.8
56.1
94.3
5.9
57.9
95.0
6.0
62.2
96.4
6.1
66.1
97.8
6.2
68.3
98.6
6.3
71.8
100.2
6.4
76.3
101.8
6.5
78.8
102.7
6.6
81.3
103.9
6.7
86.2
105.7
6.8
88.9
106.7
6.9
90.4
107.2
7.0
95.5
109.1
7.1
98.0
110.0
7.0
94.6
108.7
7.2
99.4
110.5
7.2
101.8
111.4
7.1
98.7
110.3
7.3
103.3
112.0
7.4
105.5
112.8
COP
3.2
3.4
3.5
3.5
3.7
3.8
3.9
4.0
4.2
4.2
4.3
4.5
4.6
4.6
4.8
4.8
4.9
5.0
5.0
5.0
5.1
5.1
5.1
5.2
5.2
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
50VQP096
3200 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
24
12
18
24
12
18
24
12
18
24
12
18
24
12
18
24
12
18
24
12
18
24
12
18
24
12
18
24
12
18
24
12
18
24
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
14.1
32.6
3.8
8.7
8.0
18.6
13.0
29.9
3.4
7.8
7.2
16.7
11.8
27.2
3.1
7.2
6.8
15.6
11.2
25.9
2.4
5.6
5.6
12.9
9.6
22.2
2.3
5.2
5.3
12.2
9.2
21.2
2.1
4.8
5.0
11.5
8.7
20.2
2.1
4.8
4.9
11.3
8.6
20.0
2.0
4.7
4.8
11.2
8.6
19.8
1.9
4.5
4.7
10.9
8.4
19.4
1.9
4.3
4.6
10.5
8.2
18.9
1.8
4.1
4.4
10.2
8.0
18.5
TC
89.1
79.1
73.7
99.8
94.6
91.2
103.1
101.6
100.1
102.2
103.2
103.2
98.7
101.2
102.2
93.7
97.0
98.5
90.9
94.3
95.9
88.1
91.5
93.3
83.2
86.2
87.9
79.5
81.6
82.9
78.3
78.7
79.3
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
EER
Operation Not Recommended
62.2
3.9
102.5
22.8
54.9
3.2
90.0
24.7
51.1
2.9
83.5
25.8
69.8
4.9
116.4
20.5
66.1
4.3
109.4
21.8
63.6
4.1
105.1
22.5
72.3
5.5
121.8
18.8
71.1
5.1
119.0
19.9
70.0
4.9
116.8
20.5
72.0
6.0
122.6
17.1
72.5
5.7
122.5
18.3
72.3
5.5
121.9
18.8
70.1
6.4
120.6
15.4
71.5
6.1
122.1
16.6
72.0
6.0
122.5
17.1
67.6
6.9
117.1
13.6
69.3
6.6
119.4
14.8
70.1
6.4
120.4
15.4
66.3
7.1
115.3
12.8
67.9
6.8
117.5
13.9
68.8
6.6
118.6
14.5
65.0
7.4
113.5
11.9
66.6
7.1
115.6
13.0
67.5
6.9
116.8
13.6
63.2
8.1
110.9
10.2
64.2
7.7
112.4
11.2
64.9
7.5
113.3
11.8
62.7
9.1
110.5
8.8
62.8
8.5
110.5
9.6
63.1
8.2
110.9
10.1
65.0
10.4
113.8
7.5
63.2
9.5
111.2
8.3
62.8
9.2
110.6
8.7
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
HC
64.6
71.0
74.1
75.8
82.0
85.9
88.1
93.7
98.5
101.1
105.9
111.6
114.7
118.2
124.7
128.3
130.4
137.5
141.3
136.3
143.6
147.5
142.2
149.8
153.8
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
6.2
43.3
88.3
6.4
49.2
90.2
6.5
52.0
91.1
6.5
53.5
91.5
6.7
59.1
93.3
6.8
62.7
94.5
6.9
64.7
95.1
7.0
69.6
96.7
7.2
74.0
98.1
7.2
76.5
98.8
7.4
80.6
100.4
7.5
85.8
102.0
7.6
88.7
103.0
7.7
91.8
104.1
7.9
97.7
106.0
8.0
100.9
107.0
8.1
102.8
107.6
8.3
109.2
109.7
8.4
112.7
110.8
8.3
108.1
109.4
8.5
114.7
111.5
8.6
118.2
112.7
8.4
113.5
111.1
8.7
120.2
113.3
8.8
123.7
114.5
COP
3.0
3.3
3.4
3.4
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.7
4.9
4.9
4.8
5.0
5.0
4.9
5.1
5.1
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP096 UNIT
(Cv = 37, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
12
0.11
0.3
18
0.24
0.5
24
0.42
1.0
15
Performance data (cont)
50VQP120
4000 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
15.0
22.5
30.0
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
10.2
23.5
2.1
4.8
5.3
12.2
9.4
21.6
1.9
4.3
4.8
11.1
8.6
19.8
1.7
4.0
4.4
10.1
8.1
18.8
1.3
3.0
3.7
8.6
7.0
16.2
1.2
2.7
3.5
8.1
6.7
15.4
1.1
2.4
3.3
7.6
6.4
14.7
1.1
2.4
3.2
7.4
6.3
14.4
1.0
2.3
3.2
7.4
6.2
14.3
0.9
2.2
3.1
7.2
6.0
13.9
0.9
2.0
3.0
6.9
5.8
13.4
0.8
1.9
2.9
6.7
5.6
13.0
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
Operation Not Recommended
142.3
97.1
6.3
163.6
144.2
97.0
6.0
164.7
144.9
96.7
5.9
164.9
138.6
96.0
6.6
161.3
141.5
96.9
6.3
163.2
142.7
97.1
6.2
163.9
133.9
94.0
7.1
158.1
137.5
95.6
6.8
160.6
139.1
96.2
6.6
161.7
128.4
91.4
7.6
154.4
132.4
93.3
7.3
157.1
134.3
94.2
7.1
158.5
122.1
88.2
8.2
150.2
126.4
90.3
7.8
153.1
128.5
91.3
7.6
154.5
115.4
85.0
9.0
145.9
119.6
87.0
8.5
148.5
121.8
88.1
8.2
149.9
111.9
83.5
9.4
143.8
116.2
85.5
8.9
146.4
118.3
86.5
8.6
147.7
108.5
81.9
9.8
141.7
112.7
83.9
9.2
144.2
114.9
84.9
9.0
145.5
102.1
79.3
10.7
138.5
106.1
80.9
10.1
140.5
108.2
81.8
9.8
141.6
96.1
77.2
11.7
136.1
99.7
78.4
11.1
137.5
101.7
79.1
10.8
138.4
90.6
76.0
12.9
134.7
93.8
76.6
12.2
135.4
95.5
77.0
11.8
135.9
TC
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP120 UNIT
(Cv = 37, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
15.0
0.16
0.4
22.5
0.37
0.9
30.0
0.66
1.5
16
EER
22.8
24.1
24.7
20.8
22.3
23.0
18.8
20.3
21.0
16.8
18.2
19.0
14.8
16.2
16.9
12.9
14.1
14.8
12.0
13.2
13.8
11.1
12.2
12.8
9.6
10.5
11.0
8.2
9.0
9.5
7.0
7.7
8.1
HC
82.0
88.8
92.1
93.9
100.9
105.4
107.8
114.4
120.0
123.1
129.7
136.4
140.2
145.5
153.4
157.7
160.5
169.1
173.8
169.9
174.6
177.2
179.4
180.0
180.5
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
7.7
55.7
88.6
7.9
61.9
90.2
7.9
65.0
90.9
8.0
66.7
91.4
8.1
73.1
93.0
8.2
77.3
94.0
8.3
79.5
94.6
8.5
85.6
96.0
8.6
90.8
97.3
8.6
93.7
98.1
8.8
99.7
99.6
8.9
106.0
101.1
9.0
109.5
102.0
9.1
114.4
103.2
9.3
121.7
105.0
9.4
125.7
106.0
9.4
128.2
106.6
9.6
136.2
108.6
9.8
140.5
109.7
9.7
136.8
109.0
9.5
142.0
110.6
9.5
144.8
111.4
10.0
145.3
111.4
9.4
147.8
112.5
9.2
149.1
113.1
COP
3.1
3.3
3.4
3.4
3.6
3.7
3.8
4.0
4.1
4.2
4.3
4.5
4.6
4.7
4.8
4.9
5.0
5.1
5.2
5.1
5.4
5.5
5.3
5.6
5.8
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
50VQP150
5000 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
38
19
28
38
19
28
38
19
28
38
19
28
38
19
28
38
19
28
38
19
28
38
19
28
38
19
28
38
19
28
38
19
28
38
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
12.0
27.6
2.7
6.3
6.2
14.3
11.0
25.4
2.3
5.4
5.6
12.8
10.0
23.2
2.1
4.9
5.2
12.0
9.5
21.9
1.7
3.8
4.3
9.9
8.0
18.5
1.5
3.5
4.1
9.4
7.7
17.8
1.4
3.2
3.8
8.8
7.4
17.0
1.4
3.1
3.8
8.7
7.3
16.7
1.3
3.0
3.7
8.5
7.2
16.6
1.2
2.9
3.6
8.2
7.0
16.1
1.2
2.7
3.4
7.9
6.8
15.6
1.1
2.5
3.3
7.7
6.5
15.1
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
Operation Not Recommended
175.0
131.8
8.3
203.4
173.8
138.0
7.9
200.8
172.3
141.6
7.7
198.6
173.5
123.9
8.9
204.0
174.8
129.0
8.5
203.9
174.9
132.2
8.3
203.1
169.2
117.6
9.5
201.8
172.4
121.6
9.1
203.4
173.6
124.2
8.9
203.9
163.0
112.7
10.2
197.7
167.3
115.8
9.7
200.5
169.5
117.8
9.5
201.8
155.5
108.5
11.0
192.9
160.6
111.0
10.4
196.2
163.3
112.6
10.2
198.0
147.2
104.9
11.8
187.6
152.6
107.1
11.3
191.0
155.6
108.4
11.0
193.0
142.9
103.2
12.4
185.0
148.2
105.3
11.8
188.3
151.3
106.5
11.4
190.2
138.6
101.6
12.9
182.4
143.9
103.5
12.2
185.6
146.9
104.7
11.9
187.5
130.3
98.4
14.0
178.1
135.2
100.3
13.3
180.6
138.1
101.4
12.9
182.2
123.0
95.5
15.4
175.4
127.2
97.2
14.5
176.8
129.8
98.2
14.1
177.9
117.3
93.0
17.0
175.2
120.4
94.4
16.0
175.0
122.4
95.3
15.5
175.3
TC
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
EER
21.0
21.9
22.4
19.4
20.6
21.1
17.8
19.0
19.6
16.0
17.2
17.9
14.2
15.4
16.1
12.4
13.5
14.2
11.6
12.7
13.3
10.8
11.8
12.4
9.3
10.2
10.7
8.0
8.7
9.2
6.9
7.5
7.9
HC
105.5
115.1
119.5
122.2
131.5
137.2
140.7
149.0
156.0
160.3
167.9
176.1
181.1
187.1
196.3
201.9
205.2
215.0
220.8
213.8
223.7
229.3
222.4
232.3
237.9
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
10.3
70.5
89.0
10.5
79.1
90.7
10.7
83.1
91.5
10.7
85.5
92.0
11.0
94.0
93.7
11.1
99.2
94.8
11.2
102.5
95.4
11.4
110.1
96.9
11.5
116.6
98.2
11.6
120.6
99.0
11.8
127.5
100.5
12.0
135.1
102.0
12.1
139.7
103.0
12.3
145.1
104.2
12.5
153.6
105.9
12.7
158.7
106.9
12.7
161.7
107.5
13.0
170.6
109.4
13.2
175.8
110.4
13.0
169.5
109.1
13.3
178.3
111.0
13.5
183.3
112.0
13.2
177.3
110.7
13.6
186.0
112.5
13.8
190.9
113.6
COP
3.0
3.2
3.3
3.3
3.5
3.6
3.7
3.8
4.0
4.0
4.2
4.3
4.4
4.5
4.6
4.7
4.7
4.8
4.9
4.8
4.9
5.0
4.9
5.0
5.1
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP150 UNIT
(Cv = 57, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
19
0.11
0.3
28
0.24
0.6
38
0.44
1.0
17
Performance data (cont)
50VQP168
5600 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
21.0
31.5
42.0
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
11.3
26.0
2.7
6.2
6.1
14.2
10.4
24.0
2.4
5.5
5.6
12.9
9.5
21.9
2.2
5.1
5.2
12.0
8.9
20.6
1.5
3.5
4.0
9.3
7.3
16.8
1.4
3.2
3.8
8.7
6.9
16.0
1.3
2.9
3.5
8.2
6.6
15.2
1.3
2.8
3.5
8.0
6.5
15.0
1.2
2.7
3.4
7.9
6.4
14.8
1.1
2.6
3.3
7.6
6.2
14.4
1.0
2.4
3.2
7.3
6.1
14.0
1.0
2.2
3.0
7.0
5.9
13.6
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
Operation Not Recommended
163.5
114.1
7.6
189.5
154.3
107.0
7.0
178.2
149.0
103.1
6.7
172.0
172.9
122.0
8.6
202.1
167.9
117.7
8.0
195.2
164.6
115.0
7.7
191.0
176.0
125.6
9.4
208.1
174.5
123.6
8.9
204.8
173.0
122.1
8.6
202.4
173.9
125.5
10.3
208.9
175.2
125.3
9.7
208.3
175.2
124.8
9.4
207.4
169.6
124.3
11.2
207.6
172.8
125.3
10.6
208.8
174.0
125.6
10.3
209.0
163.8
122.0
12.1
205.1
168.3
123.8
11.5
207.5
170.4
124.6
11.2
208.5
159.7
120.2
12.7
202.9
164.6
122.3
12.0
205.5
166.9
123.2
11.7
206.7
155.6
118.5
13.2
200.7
160.9
120.7
12.5
203.5
163.4
121.8
12.1
204.9
147.0
114.9
14.5
196.3
152.5
117.2
13.7
199.1
155.2
118.3
13.3
200.5
138.4
111.6
15.9
192.8
143.7
113.6
15.0
194.9
146.4
114.7
14.6
196.1
130.6
109.2
17.7
191.0
135.2
110.5
16.6
191.8
137.7
111.4
16.1
192.6
TC
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP168 UNIT
(Cv = 37, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
21.0
0.08
0.2
31.5
0.18
0.4
42.0
0.32
0.7
18
EER
21.3
21.9
22.0
20.1
20.9
21.2
18.6
19.6
20.0
16.9
18.0
18.6
15.2
16.3
16.9
13.4
14.6
15.2
12.6
13.7
14.3
11.7
12.8
13.4
10.1
11.1
11.6
8.6
9.5
10.0
7.3
8.1
8.5
HC
116.0
126.5
131.7
134.5
145.2
152.0
155.9
165.5
174.0
178.7
186.5
196.5
201.9
207.5
218.4
224.2
227.6
238.8
244.6
236.8
247.6
252.9
246.0
256.4
261.4
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
10.7
79.5
86.7
11.0
89.1
88.4
11.1
93.7
89.2
11.2
96.4
89.6
11.5
106.0
91.3
11.7
112.3
92.4
11.8
115.8
93.1
12.0
124.5
94.6
12.2
132.3
96.0
12.4
136.6
96.7
12.6
143.6
98.0
12.8
152.7
99.6
13.0
157.6
100.4
13.2
162.6
101.3
13.5
172.5
103.1
13.6
177.7
104.0
13.7
180.9
104.6
14.0
190.9
106.4
14.2
196.0
107.3
14.0
189.1
106.1
14.3
198.8
107.8
14.5
203.5
108.6
14.3
197.4
107.5
14.6
206.7
109.2
14.8
211.1
110.0
COP
3.2
3.4
3.4
3.5
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.5
4.5
4.6
4.8
4.8
4.9
5.0
5.0
5.0
5.1
5.1
5.1
5.1
5.2
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
50VQP192
6400 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
48
24
36
48
24
36
48
24
36
48
24
36
48
24
36
48
24
36
48
24
36
48
24
36
48
24
36
48
24
36
48
24
36
48
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
15.9
36.7
4.2
9.8
9.0
20.9
14.6
33.7
3.8
8.7
8.1
18.8
13.3
30.6
3.5
8.1
7.6
17.6
12.6
29.1
2.7
6.3
6.3
14.5
10.8
24.9
2.6
5.9
6.0
13.8
10.3
23.8
2.4
5.5
5.6
13.0
9.8
22.7
2.4
5.4
5.6
12.8
9.7
22.4
2.3
5.3
5.5
12.6
9.6
22.3
2.2
5.1
5.3
12.2
9.4
21.8
2.1
4.9
5.1
11.9
9.2
21.3
2.0
4.7
5.0
11.5
9.0
20.8
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
Operation Not Recommended
178.3
124.3
7.8
205.0
158.1
109.8
6.4
180.0
147.4
102.1
5.7
166.9
199.6
139.6
9.7
232.7
189.3
132.1
8.7
218.9
182.5
127.2
8.1
210.2
206.1
144.7
11.0
243.6
203.2
142.3
10.2
238.0
200.2
140.0
9.8
233.5
204.4
144.1
11.9
245.1
206.5
144.9
11.3
245.0
206.4
144.7
11.0
243.8
197.4
140.3
12.8
241.1
202.5
143.0
12.2
244.2
204.4
143.9
11.9
245.1
187.4
135.1
13.7
234.3
194.0
138.5
13.1
238.7
197.0
140.1
12.8
240.8
181.8
132.6
14.3
230.6
188.5
135.9
13.6
235.0
191.8
137.5
13.3
237.2
176.3
130.1
14.8
226.9
183.1
133.3
14.1
231.2
186.6
135.0
13.8
233.5
166.4
126.3
16.3
221.9
172.4
128.5
15.3
224.8
175.8
129.9
14.9
226.7
159.0
125.4
18.1
220.9
163.2
125.6
16.9
220.9
165.8
126.2
16.4
221.7
156.6
130.1
20.8
227.6
157.4
126.4
19.1
222.4
158.7
125.6
18.3
221.3
TC
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
EER
22.8
24.7
25.8
20.5
21.8
22.5
18.7
19.9
20.4
17.0
18.2
18.7
15.3
16.4
17.0
13.6
14.7
15.3
12.7
13.8
14.4
11.8
12.9
13.5
10.2
11.2
11.7
8.7
9.6
10.1
7.5
8.2
8.6
HC
129.2
142.1
148.2
151.5
164.0
171.9
176.2
187.3
196.9
202.3
211.7
223.1
229.4
236.5
249.5
256.6
260.7
275.0
282.7
272.6
287.2
295.1
284.4
299.5
307.5
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
12.5
86.6
86.4
12.8
98.5
88.3
13.0
104.0
89.1
13.0
107.0
89.6
13.4
118.3
91.4
13.6
125.4
92.5
13.7
129.3
93.1
14.1
139.3
94.7
14.3
148.1
96.1
14.5
152.9
96.8
14.8
161.3
98.1
15.1
171.7
99.7
15.2
177.4
100.6
15.5
183.6
101.6
15.8
195.4
103.4
16.0
201.8
104.4
16.2
205.6
105.0
16.6
218.4
107.0
16.8
225.3
108.1
16.5
216.2
106.7
17.0
229.4
108.8
17.2
236.4
109.9
16.9
226.9
108.4
17.3
240.3
110.5
17.6
247.4
111.6
COP
3.0
3.2
3.3
3.4
3.6
3.7
3.7
3.9
4.0
4.1
4.2
4.4
4.4
4.5
4.6
4.7
4.8
4.9
5.0
4.9
5.0
5.1
5.0
5.1
5.2
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP192 UNIT
(Cv = 37, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
24
0.11
0.3
36
0.24
0.5
48
0.42
1.0
19
Performance data (cont)
50VQP240
8000 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
60
30
45
60
30
45
60
30
45
60
30
45
60
30
45
60
30
45
60
30
45
60
30
45
60
30
45
60
30
45
60
30
45
60
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
11.4
26.4
2.4
5.4
5.9
13.7
10.5
24.3
2.1
4.9
5.4
12.5
9.7
22.3
1.9
4.5
4.9
11.4
9.2
21.1
1.4
3.3
4.2
9.7
7.9
18.2
1.3
3.0
3.9
9.1
7.5
17.4
1.2
2.7
3.7
8.6
7.2
16.5
1.2
2.7
3.7
8.5
7.0
16.3
1.1
2.6
3.6
8.3
7.0
16.1
1.1
2.4
3.5
8.1
6.7
15.6
1.0
2.3
3.4
7.8
6.5
15.1
0.9
2.2
3.3
7.6
6.3
14.6
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
Operation Not Recommended
284.5
194.1
12.5
327.2
288.5
194.0
12.0
329.4
289.9
193.3
11.7
329.9
277.2
192.1
13.3
322.6
283.0
193.8
12.7
326.4
285.5
194.2
12.4
327.9
267.8
188.1
14.2
316.3
274.9
191.1
13.5
321.1
278.2
192.3
13.2
323.3
256.7
182.8
15.3
308.8
264.8
186.6
14.5
314.3
268.6
188.3
14.2
316.9
244.2
176.4
16.5
300.5
252.7
180.6
15.6
306.1
256.9
182.7
15.2
308.9
230.7
169.9
17.9
291.8
239.3
174.1
17.0
297.1
243.5
176.2
16.5
299.8
223.8
166.9
18.7
287.7
232.3
170.9
17.7
292.7
236.6
173.0
17.2
295.4
216.9
163.9
19.5
283.5
225.4
167.7
18.5
288.3
229.7
169.8
17.9
291.0
204.2
158.6
21.3
277.0
212.2
161.8
20.2
281.0
216.3
163.6
19.6
283.3
192.2
154.4
23.4
272.2
199.5
156.8
22.1
275.0
203.3
158.3
21.5
276.7
181.2
151.9
25.8
269.4
187.6
153.2
24.4
270.8
191.0
154.1
23.7
271.8
TC
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP240 UNIT
(Cv = 37, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
30
0.16
0.4
45
0.37
0.9
60
0.66
1.5
20
EER
22.8
24.1
24.7
20.8
22.3
23.0
18.8
20.2
21.0
16.7
18.1
18.9
14.7
16.0
16.7
12.8
14.0
14.7
11.9
13.1
13.7
11.1
12.2
12.7
9.5
10.5
11.0
8.1
9.0
9.4
7.0
7.6
8.0
HC
164.1
177.5
184.1
187.8
201.9
210.7
215.6
228.9
240.0
246.2
259.3
272.8
280.3
291.1
306.8
315.4
320.9
338.3
347.7
339.9
349.2
354.3
358.8
360.1
361.0
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
15.5
111.3
86.7
15.7
123.8
88.3
15.9
129.9
89.0
16.0
133.3
89.4
16.3
146.3
91.0
16.5
154.5
92.1
16.6
159.1
92.6
16.9
171.2
94.1
17.1
181.6
95.4
17.3
187.4
96.1
17.6
199.4
97.3
17.8
212.0
98.9
18.0
219.0
99.7
18.3
228.8
100.7
18.6
243.4
102.4
18.8
251.3
103.4
18.9
256.5
104.0
19.3
272.5
106.0
19.5
281.0
107.0
19.4
273.6
105.7
19.1
284.0
107.7
19.0
289.7
108.7
20.0
290.7
107.3
18.9
295.6
109.4
18.4
298.3
110.4
COP
3.1
3.3
3.4
3.4
3.6
3.7
3.8
4.0
4.1
4.2
4.3
4.5
4.6
4.7
4.8
4.9
5.0
5.1
5.2
5.1
5.2
5.3
5.2
5.4
5.4
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
50VQP300
10,000 CFM NOMINAL AIRFLOW
EWT (F)
GPM
20
76
38
56
76
38
56
76
38
56
76
38
56
76
38
56
76
38
56
76
38
56
76
38
56
76
38
56
76
38
56
76
38
56
76
30
40
50
60
70
80
85
90
100
110
120
COP —
Cv
—
EAT —
EER —
EWT —
HC
—
HE
—
HR
—
kW
—
MBtuh —
MOPD —
LAT —
SC
—
TC
—
WPD —
WPD*
psig
ft wg
13.5
31.2
3.1
7.1
7.0
16.1
12.4
28.7
2.6
6.1
6.3
14.5
11.3
26.2
2.4
5.6
5.9
13.6
10.7
24.7
1.9
4.3
4.8
11.2
9.1
20.9
1.7
4.0
4.6
10.6
8.7
20.1
1.6
3.6
4.3
9.9
8.3
19.2
1.6
3.5
4.3
9.8
8.2
18.9
1.5
3.4
4.2
9.6
8.1
18.7
1.4
3.2
4.0
9.3
7.9
18.1
1.3
3.0
3.9
9.0
7.6
17.6
1.2
2.9
3.7
8.6
7.4
17.1
COOLING CAPACITY, EAT 80/67 F
SC
kW
HR
Operation Not Recommended
350.0
263.5
16.7
406.9
347.6
276.0
15.9
401.7
344.6
283.3
15.4
397.1
347.1
247.7
17.8
408.0
349.7
258.0
17.0
407.7
349.8
264.4
16.6
406.2
338.5
235.2
19.1
403.5
344.8
243.3
18.2
406.8
347.3
248.4
17.7
407.7
325.9
225.3
20.4
395.4
334.7
231.6
19.4
401.0
338.9
235.6
18.9
403.5
311.0
217.0
21.9
385.7
321.2
222.1
20.9
392.5
326.6
225.2
20.3
396.0
294.4
209.7
23.7
375.1
305.2
214.1
22.5
382.1
311.2
216.7
21.9
386.0
285.8
206.4
24.7
370.0
296.5
210.6
23.5
376.6
302.5
213.1
22.9
380.5
277.1
203.1
25.7
364.9
287.8
207.1
24.4
371.2
293.9
209.4
23.8
375.0
260.7
196.9
28.0
356.3
270.5
200.6
26.6
361.2
276.3
202.8
25.8
364.4
246.0
191.0
30.7
350.9
254.4
194.5
29.1
353.6
259.5
196.5
28.2
355.8
234.6
186.0
33.9
350.4
240.8
188.8
32.0
349.9
244.9
190.6
31.0
350.6
TC
LEGEND
Coefficient of Performance
Coefficient of Velocity
Entering Air Temperature (F)
Energy Efficiency Ratio
Entering Water Temperature (F)
Heating Capacity (MBtuh)
Heat of Extraction (MBtuh)
Heat of Rejection (MBtuh)
Total Power (Kilowatts)
Btuh in Thousands
Maximum Opening Pressure Difference
Leaving Air Temperature (F)
Sensible Cooling Capacity (MBtuh)
Total Cooling Capacity (MBtuh)
Water Pressure Differential
EER
21.0
22.0
22.4
19.4
20.5
21.1
17.7
18.9
19.5
15.9
17.1
17.8
14.1
15.3
15.9
12.4
13.5
14.1
11.5
12.6
13.2
10.7
11.7
12.3
9.3
10.1
10.7
8.0
8.7
9.2
6.9
7.5
7.9
HC
211.0
230.1
238.9
244.3
262.9
274.3
281.3
298.0
312.0
320.6
335.8
352.3
362.3
374.2
392.7
403.7
410.4
430.1
441.6
427.6
447.4
458.7
444.9
464.7
475.8
HEATING CAPACITY, EAT 70 F
kW
HE
LAT
20.5
141.0
87.1
21.1
158.2
88.9
21.3
166.1
89.7
21.5
171.0
90.1
22.0
188.0
91.8
22.2
198.5
92.9
22.4
204.9
93.5
22.8
220.3
95.0
23.1
233.2
96.3
23.3
241.2
97.1
23.7
255.0
98.3
24.0
270.3
99.8
24.3
279.5
100.7
24.6
290.2
101.7
25.0
307.2
103.3
25.3
317.3
104.3
25.5
323.4
104.9
26.0
341.3
106.7
26.4
351.6
107.7
26.0
339.0
106.5
26.6
356.7
108.2
27.0
366.7
109.3
26.5
354.6
108.0
27.1
372.1
109.8
27.6
381.7
110.8
COP
3.0
3.2
3.3
3.3
3.5
3.6
3.7
3.8
4.0
4.0
4.2
4.3
4.4
4.5
4.6
4.7
4.7
4.8
4.9
4.8
4.9
5.0
4.9
5.0
5.1
Operation Not Recommended
NOTES:
1. Interpolation is permissable, extrapolation is not.
2. All entering air conditions are 80 F db (dry bulb) and 67 F wb (wet
bulb) in cooling and 70 F db in heating.
3. All performance data is based upon the lower voltage of dual voltage rated units.
4. See performance correction tables for operating conditions other
than those listed above.
5. For operation in the shaded area when water is used in lieu of an
antifreeze solution, the LWT (leaving water temperature) must be
calculated. Flow must be maintained to a level so that the LWT is
maintained above 42 F when the JW3 jumper is not clipped.
Because the refrigerant temperature can potentially reach as low
as 32 F with 40 F LWT, a nuisance cutout could occur due to the
activation of the low temperature protection. The JW3 jumper
should never be clipped for standard range equipment or systems
without antifreeze.
*WPD ADDER FOR MOTORIZED WATER VALVE, 50VQP300 UNIT
(Cv = 57, MOPD = 150 psig)
WPD Adder
GPM
PSIG
FT
38
0.11
0.3
56
0.24
0.6
76
0.44
1.0
21
Performance data (cont)
AIRFLOW CORRECTION TABLE
PERCENTAGE
OF RATE
AIRFLOW
75
81
88
94
100
106
113
119
125
HC
HE
HR
kW
SC
TC
—
—
—
—
—
—
COOLING
HEATING
TC
SC
kW
HR
HC
kW
HE
0.957
0.970
0.982
0.991
1.000
1.002
1.004
1.008
1.013
0.868
0.901
0.940
0.970
1.000
1.025
1.050
1.073
1.095
0.944
0.957
0.971
0.985
1.000
1.013
1.026
1.042
1.058
0.954
0.967
0.980
0.990
1.000
1.004
1.009
1.015
1.022
0.960
0.971
0.983
0.991
1.000
1.006
1.013
1.021
1.029
1.045
1.027
1.015
1.007
1.000
0.999
0.998
0.997
0.996
0.938
0.956
0.974
0.987
1.000
1.009
1.019
1.028
1.038
LEGEND
Heating Capacity
Heat of Extraction
Heat of Rejection
Total Power
Sensible Cooling Capacity
Total Cooling Capacity
ENTERING AIR CORRECTION TABLE — HEATING
EAT (db, F)
60
65
68
70
75
80
db
EAT
HC
HE
kW
—
—
—
—
—
HC
1.022
1.010
1.004
1.000
0.991
0.982
kW
0.916
0.957
0.982
1.000
1.045
1.101
HE
1.051
1.025
1.010
1.000
0.976
0.948
LEGEND
Dry Bulb
Entering Air Temperature
Heating Capacity
Heat of Extraction
Total Power
ENTERING AIR CORRECTION TABLE — COOLING
EAT (wb, F)
TC
60.0
65.0
66.2
67.0
70.0
75.0
0.954
0.975
0.988
1.000
1.045
1.122
70
0.866
0.657
0.603
0.568
—
—
SENSIBLE COOLING CAPACITY MULTIPLIER, ENTERING (db, F)
75
80
80.6
85
90
1.076
1.211
1.233
*
*
0.872
1.096
1.115
1.279
*
0.818
1.043
1.064
1.246
*
0.782
1.006
1.027
1.213
1.350
0.647
0.871
0.889
1.084
1.295
—
0.644
0.658
0.855
1.076
LEGEND
ARI
— Air Conditioning and Refrigeration Institute
ASRAHE — American Society of Heating, Refrigeration and
Air Conditioning Engineers
db
— Dry Bulb
EAT
— Entering Air Temperature
HR
— Heat of Rejection
ISO
— International Organization for Standardization
kW
— Total Power
TC
— Total Capacity
wb
— Wet Bulb
*Sensible capacity equals total capacity.
NOTE: ARI/ISO/ASHRAE 13256-1 uses entering air conditions of
cooling - 80.6 F db/66.2 F wb, and heating - 68 F db/59 F wb entering
air temperature.
22
95
*
*
*
1.421
1.421
1.294
kW
HR
0.991
0.995
0.998
1.000
1.009
1.025
0.962
0.979
0.990
1.000
1.037
1.103
ANTIFREEZE CORRECTION TABLE
ANTIFREEZE
TYPE
ANTIFREEZE
PERCENTAGE
Water
0
5
15
25
5
15
25
5
15
25
5
15
25
Propylene
Glycol
Methanol
Ethanol
Ethylene
Glycol
Total Capacity
1.000
0.995
0.986
0.978
0.997
0.990
0.982
0.998
0.994
0.986
0.998
0.994
0.988
COOLING
EWT 90F
Sensible Capacity
1.000
0.995
0.986
0.978
0.997
0.990
0.982
0.998
0.994
0.986
0.998
0.994
0.988
kW
1.000
1.003
1.009
1.014
1.002
1.007
1.012
1.002
1.005
1.009
1.002
1.004
1.008
HEATING
EWT 30 F
Heating Capacity
—
0.989
0.968
0.947
0.989
0.968
0.949
0.981
0.944
0.917
0.993
0.980
0.966
kW
—
0.997
0.990
0.983
0.997
0.990
0.984
0.994
0.983
0.974
0.998
0.994
0.990
WATER
PRESSURE DROP,
EWT 30 F
1.00
1.07
1.21
1.36
1.07
1.16
1.22
1.14
1.30
1.36
1.04
1.12
1.20
LEGEND
EWT — Entering Water Temperature
DRY COIL TO WET COIL CONVERSION TABLE
AIR COIL FACE
VELOCITY (FPM)
175
250
325
400
475
550
REQUIRED BHP
MULTIPLIER
1.00
0.99
0.99
0.98
0.98
0.97
REQUIRED RPM
MULTIPLIER
1.00
0.99
0.98
0.97
0.96
0.95
LEGEND
bhp — Brake Horsepower
NOTES:
1. Sheave turns and RPM relationship is unchanged; use original
blower performance table to find correct turns based upon new
RPM.
2. Example: 50VQP084 dry coil performance is 0.92 bhp, 867 rpm at
2600 cfm (or 2600 cfm/9 sq ft coil = 290 fpm). Wet coil performance would be 0.92 x 0.99 = 0.91 bhp required and 867 rpm x
0.98 = 850 rpm required.
23
Performance data (cont)
50VQP084 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
3100
3200
3300
3400
3500
A
B
bhp
C
D
E
ESP
24
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.43
B
412
5.0
0.44
B
421
4.5
0.49
B
441
4.0
0.54
B
456
3.5
0.63
B
471
3.0
0.64
B
486
2.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
—
—
—
—
—
—
—
—
—
—
—
—
0.29
B
403
5.0
0.31
B
411
5.0
0.34
B
420
4.5
0.38
B
423
4.5
0.39
B
431
4.5
0.44
B
440
4.0
0.49
B
455
3.5
0.53
B
459
3.5
0.54
B
478
3.0
0.64
B
495
2.5
0.69
B
506
2.0
0.74
A
520
6.0
0.2
0.24
B
410
5.0
0.28
B
424
4.5
0.29
B
435
4.5
0.34
B
446
4.0
0.34
B
452
4.0
0.43
B
460
3.5
0.43
B
463
3.5
0.44
B
474
3.0
0.49
B
481
3.0
0.54
B
492
2.5
0.59
B
499
2.5
0.64
B
513
2.0
0.69
A
529
6.0
0.74
A
539
5.5
0.79
A
555
5.5
0.3
0.29
B
457
3.5
0.32
B
467
3.5
0.34
B
476
3.0
0.39
B
485
3.0
0.39
B
495
2.5
0.48
B
500
2.5
0.48
B
504
2.0
0.49
B
510
2.0
0.54
B
517
2.0
0.59
A
526
6.0
0.64
A
533
6.0
0.69
A
549
5.5
0.74
A
561
5.0
0.79
A
574
5.0
0.84
A
586
4.5
0.4
0.34
B
499
4.5
0.34
B
507
4.5
0.39
B
518
4.0
0.44
A
527
6.0
0.44
A
532
6.0
0.53
A
536
6.0
0.53
A
539
5.5
0.54
A
545
5.5
0.59
A
551
5.5
0.64
A
563
5.5
0.69
A
569
5.0
0.74
A
581
5.0
0.83
A
595
4.5
0.84
A
604
4.0
0.94
A
615
4.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
1.1
0.37
0.41
0.44
0.49
0.54
0.59
0.64
A
A
A
A
A
A
C
537
577
612
647
678
710
737
6.0
5.0
4.0
3.0
2.5
1.5
6.0
0.39
0.44
0.49
0.54
0.59
0.64
0.69
A
A
A
A
A
A
C
548
584
621
653
684
716
743
5.5
5.0
4.0
3.0
2.0
1.5
6.0
0.44
0.49
0.54
0.59
0.64
0.69
0.74
A
A
A
A
A
A
C
555
590
627
659
692
721
751
5.5
4.5
3.5
2.5
2.0
1.5
5.5
0.49
0.54
0.59
0.64
0.69
0.74
0.79
A
A
A
A
A
A
C
563
600
633
665
697
726
756
5.5
4.5
3.5
2.5
1.5
1.0
5.5
0.49
0.54
0.59
0.64
0.74
0.79
0.84
A
A
A
A
A
A
C
567
604
636
670
700
729
759
5.5
4.0
3.5
2.5
1.5
1.0
5.5
0.58
0.63
0.68
0.73
0.78
0.83
0.88
A
A
A
A
A
A
C
570
606
638
671
701
729
759
5.0
4.0
3.0
2.0
1.5
1.0
5.0
0.59
0.64
0.69
0.74
0.79
0.84
0.89
A
A
A
A
A
A
C
576
609
641
674
703
734
762
5.0
4.0
3.0
2.0
1.5
1.0
5.0
0.64
0.69
0.74
0.79
0.84
0.89
0.94
A
A
A
A
A
A
C
581
613
647
677
706
737
764
5.0
4.0
3.0
2.0
1.5
5.5
1.0
0.64
0.74
0.79
0.84
0.89
0.94
1.04
A
A
A
A
A
C
E
586
618
651
681
710
740
767
4.5
3.5
2.5
1.5
1.0
5.5
5.5
0.69
0.74
0.84
0.89
0.94
1.04
1.09
A
A
A
A
A
D
E
595
628
658
687
718
745
774
4.5
3.5
2.5
1.5
1.5
1.0
5.0
0.74
0.84
0.89
0.94
0.99
1.04
1.14
A
A
A
A
A
D
E
600
633
663
691
722
749
777
4.0
3.0
2.0
1.5
1.5
1.0
5.0
0.84
0.89
0.94
0.99
1.04
1.14
1.19
A
A
A
A
D
E
E
614
644
672
703
730
759
785
4.0
3.0
2.0
1.5
1.5
5.5
4.5
0.89
0.94
0.99
1.04
1.14
1.23
1.29
A
A
A
D
D
E
E
625
656
685
712
741
767
795
3.5
2.5
2.0
1.5
1.0
5.0
4.5
0.94
0.99
1.04
1.14
1.19
1.24
1.34
A
A
D
D
D
E
E
633
664
692
721
747
773
800
3.5
2.5
2.0
1.5
1.0
5.0
4.0
0.99
1.04
1.14
1.23
1.29
1.34
1.44
A
D
D
D
E
E
E
647
674
704
730
756
784
808
3.0
2.5
1.5
1.0
5.5
4.5
4.0
1.2
0.69
C
764
5.5
0.74
C
772
5.0
0.79
C
777
5.0
0.84
C
783
4.5
0.89
C
786
4.5
0.93
C
786
4.0
0.94
C
788
4.0
1.04
E
793
4.5
1.09
E
795
4.5
1.14
E
800
4.5
1.19
E
803
4.0
1.24
E
810
4.0
1.34
E
820
3.5
1.44
E
825
3.5
1.49
E
835
3.0
1.3
0.74
C
791
4.5
0.79
C
797
4.5
0.84
C
803
4.0
0.89
C
811
4.0
0.94
C
813
3.5
1.03
E
814
4.0
1.04
E
816
4.0
1.09
E
818
4.0
1.14
E
821
3.5
1.19
E
826
3.5
1.24
E
828
3.5
1.34
E
837
3.0
1.44
E
844
3.0
1.49
E
851
2.5
—
—
—
—
1.4
0.79
C
815
4.0
0.84
C
821
3.5
0.89
C
829
3.5
0.94
C
835
3.0
0.99
C
838
3.0
1.08
E
839
3.0
1.09
E
841
3.0
1.12
E
843
3.0
1.19
E
845
3.0
1.24
E
852
3.0
1.34
E
854
2.5
1.39
E
861
2.5
1.49
E
870
2.5
—
—
—
—
—
—
—
—
1.5
0.84
C
838
3.0
0.9
C
847
3.0
0.94
C
853
2.5
0.99
C
858
2.5
1.04
E
864
2.5
1.13
E
865
2.5
1.14
E
867
2.5
1.22
E
869
2.5
1.24
E
872
2.0
1.29
E
876
2.0
1.39
E
878
2.0
1.44
E
887
2.0
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
50VQP096 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
2400
2500
2600
2700
2800
2900
3000
3100
3200
3300
3400
3500
3600
3700
3800
3900
4000
A
B
bhp
C
D
E
ESP
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.43
B
412
5.0
0.44
B
421
4.5
0.49
B
441
4.0
0.54
B
456
3.5
0.63
B
471
3.0
0.64
B
486
2.5
0.74
B
495
2.5
0.79
B
506
2.0
0.84
B
515
2.0
0.89
A
525
6.0
0.94
A
539
5.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
0.29
B
403
5.0
0.31
B
411
5.0
0.34
B
420
4.5
0.38
B
423
4.5
0.39
B
431
4.5
0.44
B
440
4.0
0.49
B
455
3.5
0.53
B
459
3.5
0.54
B
478
3.0
0.64
B
495
2.5
0.69
B
506
2.0
0.74
A
520
6.0
0.79
A
528
6.0
0.84
A
541
5.5
0.89
A
549
5.5
0.94
A
556
5.5
1.04
A
569
5.0
0.2
0.34
B
446
4.0
0.34
B
452
4.0
0.43
B
460
3.5
0.43
B
463
3.5
0.44
B
474
3.0
0.49
B
481
3.0
0.54
B
492
2.5
0.59
B
499
2.5
0.64
B
513
2.0
0.69
A
529
6.0
0.74
A
539
5.5
0.79
A
555
5.5
0.84
A
562
5.0
0.93
A
572
5.0
0.94
A
580
4.5
1.04
A
586
4.5
1.09
A
601
4.5
0.3
0.39
B
485
3.0
0.39
B
495
2.5
0.48
B
500
2.5
0.48
B
504
2.0
0.49
B
510
2.0
0.54
B
517
2.0
0.59
A
526
6.0
0.64
A
533
6.0
0.69
A
549
5.5
0.74
A
561
5.0
0.79
A
574
5.0
0.84
A
586
4.5
0.94
A
593
4.5
0.99
A
605
4.0
1.04
A
611
4.0
1.09
A
617
4.0
1.14
A
629
3.5
0.4
0.44
A
527
6.0
0.44
A
532
6.0
0.53
A
536
6.0
0.53
A
539
5.5
0.54
A
545
5.5
0.59
A
551
5.5
0.64
A
563
5.5
0.69
A
569
5.0
0.74
A
581
5.0
0.83
A
595
4.5
0.84
A
604
4.0
0.94
A
615
4.0
0.99
A
624
3.5
1.04
A
633
3.5
1.13
A
640
3.5
1.14
A
645
3.0
1.24
A
659
3.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
1.1
0.49
0.54
0.59
0.64
0.69
0.74
0.79
A
A
A
A
A
A
C
563
600
633
665
697
726
756
5.5
4.5
3.5
2.5
1.5
1.0
5.5
0.49
0.54
0.59
0.64
0.74
0.79
0.84
A
A
A
A
A
A
C
567
604
636
670
700
729
759
5.5
4.0
3.5
2.5
1.5
1.0
5.5
0.58
0.63
0.68
0.73
0.78
0.83
0.88
A
A
A
A
A
A
C
570
606
638
671
701
729
759
5.0
4.0
3.0
2.0
1.5
1.0
5.0
0.59
0.64
0.69
0.74
0.79
0.84
0.89
A
A
A
A
A
A
C
576
609
641
674
703
734
762
5.0
4.0
3.0
2.0
1.5
1.0
5.0
0.64
0.69
0.74
0.79
0.84
0.89
0.94
A
A
A
A
A
C
C
581
613
647
677
706
737
764
5.0
4.0
3.0
2.0
1.5
5.5
5.0
0.64
0.74
0.79
0.84
0.89
0.94
1.04
A
A
A
A
A
C
C
586
618
651
681
710
740
767
4.5
3.5
2.5
1.5
1.0
5.5
5.0
0.69
0.74
0.84
0.89
0.94
1.04
1.09
A
A
A
A
A
C
C
595
628
658
687
718
745
774
4.5
3.5
2.5
1.5
1.5
6.0
5.0
0.74
0.84
0.89
0.94
0.99
1.04
1.14
A
A
A
A
A
C
C
600
633
663
691
722
749
777
4.0
3.0
2.0
1.5
1.5
6.0
4.5
0.84
0.89
0.94
0.99
1.04
1.14
1.19
A
A
A
A
A
C
C
614
644
672
703
730
759
785
4.0
3.0
2.0
1.5
1.5
5.5
4.5
0.89
0.94
0.99
1.04
1.14
1.23
1.29
A
A
A
A
A
C
C
625
656
685
712
741
767
795
3.5
2.5
2.0
1.5
1.0
5.0
4.5
0.94
0.99
1.04
1.14
1.19
1.24
1.34
A
A
A
A
A
C
C
633
664
692
721
747
773
800
3.5
2.5
2.0
1.5
1.0
5.0
4.0
0.99
1.04
1.14
1.23
1.29
1.34
1.44
A
A
A
A
C
C
C
647
674
704
730
756
784
808
3.0
2.5
1.5
1.0
5.5
4.5
4.0
1.04
1.14
1.19
1.24
1.34
1.44
1.49
A
A
A
A
C
C
C
652
680
708
734
762
787
812
3.0
2.0
1.5
1.0
5.5
4.5
4.0
1.14
1.19
1.24
1.34
1.44
1.49
1.54
A
A
A
A
C
C
E
661
690
716
744
769
793
820
3.0
2.0
1.5
1.0
5.0
4.5
3.5
1.19
1.24
1.34
1.43
1.49
1.54
1.64
A
A
A
C
C
E
E
667
696
721
749
773
798
823
2.5
1.5
1.5
5.5
5.0
4.0
3.5
1.24
1.34
1.39
1.44
1.54
1.64
1.69
A
A
A
C
E
E
E
674
701
726
753
778
804
827
2.5
1.5
1.0
5.5
5.0
4.0
3.5
1.34
1.44
1.49
1.54
1.64
1.74
1.79
A
A
A
E
E
E
E
685
711
738
763
789
812
835
2.0
1.0
1.0
5.0
4.5
3.5
3.0
1.2
0.84
C
783
5.0
0.89
C
786
5.0
0.93
C
786
5.0
0.94
C
788
4.5
1.04
C
793
4.5
1.09
C
795
4.5
1.14
C
800
4.0
1.19
C
803
4.0
1.24
C
810
4.0
1.34
C
820
3.5
1.44
C
825
3.5
1.49
C
835
3.0
1.54
E
838
3.0
1.64
E
843
3.0
1.73
E
847
3.0
1.74
E
850
2.5
1.84
E
860
2.5
1.3
0.89
C
811
4.0
0.94
C
813
4.0
1.03
C
814
4.0
1.04
C
816
4.0
1.09
C
818
3.5
1.14
C
821
3.5
1.19
C
826
3.5
1.24
C
828
3.0
1.34
C
837
3.0
1.44
C
844
3.0
1.49
C
851
2.5
1.54
E
858
2.5
1.64
E
861
2.5
1.74
E
868
2.5
1.79
E
872
2.5
1.84
E
875
2.0
1.94
E
882
2.0
1.4
0.94
C
835
3.5
0.99
C
838
3.0
1.08
C
839
3.0
1.09
C
841
3.0
1.12
C
843
3.0
1.19
C
845
2.5
1.24
C
852
2.5
1.34
C
854
2.5
1.39
C
861
2.5
1.49
C
870
2.0
1.54
E
875
2.5
1.64
E
883
2.5
1.74
E
886
2.5
1.79
E
891
2.0
1.84
E
894
2.0
1.94
E
897
2.0
—
—
—
—
1.5
0.99
C
858
3.0
1.04
C
864
3.0
1.13
C
865
2.5
1.14
C
867
2.5
1.22
C
869
2.5
1.24
C
872
2.5
1.29
C
876
2.0
1.39
C
878
2.0
1.44
C
887
2.0
1.54
E
893
2.0
1.64
E
898
2.0
1.74
E
906
1.5
1.83
E
909
1.5
1.84
E
913
1.5
1.94
E
918
1.0
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest
voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use Dry
Coil to Wet Coil Conversion Table.
25
Performance data (cont)
50VQP120 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
3000
3100
3200
3300
3400
3500
3600
3700
3800
3900
4000
A
B
bhp
C
D
E
ESP
26
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
0.59
B
464
6.0
0.64
B
480
5.5
0.69
B
496
5.0
0.74
B
511
4.5
0.84
B
526
4.0
0.89
B
544
3.5
0.94
B
555
3.0
1.04
B
572
2.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
0.54
B
469
5.5
0.59
B
485
5.0
0.64
B
500
5.0
0.69
B
515
4.5
0.74
B
530
4.0
0.84
B
544
3.5
0.89
B
561
3.0
0.94
B
575
2.5
1.04
B
589
2.0
1.09
B
601
2.0
0.2
0.54
B
491
5.0
0.59
B
504
5.0
0.64
B
520
4.5
0.69
B
537
4.0
0.74
B
551
3.5
0.84
B
565
3.0
0.89
B
578
2.5
0.94
B
592
2.0
1.04
B
605
1.5
1.14
A
618
6.0
1.14
A
630
5.5
0.3
0.59
B
529
4.0
0.64
B
542
3.5
0.69
B
556
3.0
0.74
B
570
2.5
0.84
B
583
2.5
0.89
B
596
2.0
0.94
A
608
6.0
1.04
A
621
6.0
1.09
A
633
5.5
1.19
A
646
5.0
1.24
A
657
5.0
0.4
0.64
B
563
3.0
0.69
B
575
2.5
0.74
B
588
2.0
0.84
B
601
2.0
0.89
A
613
6.0
0.94
A
625
6.0
1.04
A
637
5.5
1.14
A
649
5.0
1.14
A
661
5.0
1.24
A
676
4.5
1.34
A
686
4.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
1.1
0.69
0.74
0.84
0.89
0.94
1.04
1.09
B
A
A
A
A
A
A
595
626
659
689
717
745
774
2.0
6.0
5.0
4.0
3.5
3.0
2.0
0.74
0.84
0.89
0.94
1.04
1.09
1.14
A
A
A
A
A
A
A
607
637
670
699
726
754
783
6.0
5.5
4.5
4.0
3.5
2.5
2.0
0.84
0.89
0.94
1.04
1.09
1.14
1.24
A
A
A
A
A
A
A
619
649
680
708
736
765
791
6.0
5.0
4.5
3.5
3.0
2.5
1.5
0.89
0.94
1.04
1.09
1.14
1.24
1.29
A
A
A
A
A
A
A
631
662
691
718
745
774
799
5.5
5.0
4.0
3.5
2.5
2.0
1.5
0.94
1.04
1.09
1.14
1.24
1.29
1.34
A
A
A
A
A
A
A
642
674
701
728
754
783
808
5.5
4.5
3.5
3.0
2.5
2.0
1.0
1.04
1.09
1.14
1.24
1.29
1.34
1.44
A
A
A
A
A
A
A
654
684
711
738
766
792
816
5.0
4.0
3.5
3.0
2.5
1.5
1.0
1.09
1.14
1.24
1.34
1.39
1.44
1.54
A
A
A
A
A
A
C
668
695
722
748
776
800
825
4.5
4.0
3.5
2.5
2.0
1.0
6.0
1.19
1.24
1.34
1.39
1.44
1.54
1.64
A
A
A
A
A
A
C
679
706
732
758
785
809
833
4.5
3.5
3.0
2.5
1.5
1.0
6.0
1.24
1.34
1.39
1.44
1.54
1.64
1.69
A
A
A
A
A
A
C
691
717
742
767
794
818
842
4.0
3.5
2.5
2.0
1.5
1.0
6.0
1.34
1.44
1.49
1.54
1.64
1.74
1.79
A
A
A
A
A
C
C
702
728
753
779
803
827
850
3.5
3.0
2.5
2.0
1.0
6.0
5.5
1.44
1.49
1.54
1.64
1.74
1.79
1.84
A
A
A
A
A
C
C
712
737
762
789
812
836
859
3.5
3.0
2.0
1.5
1.0
6.0
5.5
1.2
1.14
A
801
1.5
1.19
A
809
1.5
1.29
A
817
1.0
1.34
A
824
1.0
1.44
C
833
6.0
1.54
C
841
6.0
1.59
C
849
6.0
1.69
C
857
5.5
1.74
C
867
5.5
1.84
C
875
5.0
1.94
C
883
5.0
1.3
1.19
A
826
1.0
1.24
C
834
6.0
1.34
C
841
6.0
1.44
C
849
5.5
1.49
C
857
5.5
1.59
C
867
5.5
1.64
C
874
5.0
1.74
C
882
5.0
1.84
C
890
4.5
1.94
C
898
4.5
2.04
E
905
4.5
1.4
1.24
C
851
6.0
1.34
C
859
6.0
1.44
C
868
5.5
1.49
C
875
5.0
1.54
C
882
5.0
1.64
C
890
5.0
1.74
C
897
4.5
1.84
C
905
4.5
1.94
C
912
4.0
2.04
E
920
4.0
2.14
E
927
4.0
1.5
1.34
C
877
5.5
1.44
C
884
5.0
1.53
C
891
5.0
1.54
C
898
4.5
1.64
C
905
4.5
1.74
C
913
4.0
1.84
C
920
4.0
1.94
C
927
4.0
2.04
E
934
3.5
2.14
E
941
3.5
2.24
E
948
3.5
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
50VQP120 BLOWER PERFORMANCE DATA (cont)
AIRFLOW
(cfm)
4100
4200
4300
4400
4500
4600
4700
4800
4900
5000
A
B
bhp
C
D
E
ESP
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
1.14
B
589
2.0
1.24
A
605
6.0
1.29
A
621
6.0
1.39
A
637
5.5
1.49
A
653
5.0
1.59
A
668
4.5
1.74
A
683
4.0
1.84
A
698
3.5
1.94
A
715
3.0
2.04
D
730
3.0
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
1.19
A
617
6.0
1.29
A
633
5.5
1.34
A
649
5.0
1.44
A
664
4.5
1.54
A
679
4.5
1.64
A
694
4.0
1.84
A
711
3.5
1.94
A
725
3.0
2.04
D
739
3.0
2.14
D
753
2.5
0.2
1.24
A
645
5.0
1.34
A
660
5.0
1.44
A
675
4.5
1.54
A
690
4.0
1.64
A
707
3.5
1.74
A
721
3.0
1.89
A
735
2.5
1.99
A
749
2.5
2.14
D
762
2.5
2.24
D
776
2.0
0.3
1.34
A
672
4.5
1.44
A
689
4.0
1.54
A
703
3.5
1.64
A
717
3.5
1.74
A
731
3.0
1.84
A
745
2.5
1.94
A
758
2.0
2.04
D
772
2.0
2.24
D
785
2.0
2.34
D
798
1.5
0.4
1.44
A
700
4.0
1.54
A
714
3.5
1.64
A
728
3.0
1.74
A
742
2.5
1.84
A
755
2.0
1.94
A
768
2.0
2.04
D
782
2.0
2.14
D
795
1.5
2.34
D
810
1.0
2.44
E
822
6.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
1.1
1.49
1.54
1.64
1.74
1.84
1.89
1.94
A
A
A
A
C
C
C
726
751
775
801
824
847
872
3.0
2.5
2.0
1.0
6.0
5.5
5.0
1.59
1.64
1.74
1.84
2
2.04
2.09
A
A
A
A
E
E
E
739
763
790
813
836
858
882
2.5
2.5
1.5
1.0
6.0
5.5
5.5
1.69
1.74
1.84
2
2.04
2.14
2.24
A
A
A
E
E
E
E
752
776
802
827
847
869
893
2.5
2.0
1.0
6.0
6.0
5.5
5.0
1.84
1.89
2
2.04
2.14
2.24
2.34
A
A
D
E
E
E
E
766
791
814
836
858
882
904
2.0
1.5
1.0
6.0
5.5
5.0
4.5
1.94
2.04
2.09
2.14
2.24
2.34
2.44
A
D
D
E
E
E
E
779
804
826
848
870
893
914
1.5
1.5
1.0
6.0
5.5
5.0
4.5
2.04
2.14
2.24
2.34
2.39
2.44
2.54
D
D
E
E
E
E
E
791
816
838
860
883
904
925
1.5
1.0
6.0
5.5
5.0
4.5
4.0
2.14
2.24
2.34
2.44
2.54
2.64
2.69
D
E
E
E
E
E
E
806
828
850
871
894
915
935
1.0
6.0
6.0
5.5
5.0
4.5
3.5
2.24
2.34
2.44
2.54
2.64
2.74
2.84
D
E
E
E
E
E
E
819
836
862
883
906
926
946
1.0
6.0
5.5
5.0
4.5
4.0
3.5
2.44
2.49
2.54
2.64
2.74
2.84
2.94
E
E
E
E
E
E
E
831
853
874
896
917
937
956
6.0
5.5
5.5
5.0
4.0
3.5
3.0
2.54
2.64
2.74
2.84
2.94
—
—
E
E
E
E
E
—
—
844
865
885
908
928
—
—
6.0
5.5
5.0
4.5
4.0
—
—
1.2
2.04
E
894
4.5
2.14
E
904
4.5
2.29
E
914
4.5
2.44
E
925
4.0
2.54
E
935
4.0
2.64
E
945
3.5
2.74
E
955
3.5
2.94
E
968
3.0
—
—
—
—
—
—
—
—
1.3
2.14
E
915
4.0
2.24
E
925
4.0
2.34
E
935
4.0
2.49
E
945
3.5
2.64
E
955
3.5
2.74
E
967
3.0
2.84
E
977
3.0
—
—
—
—
—
—
—
—
—
—
—
—
1.4
2.24
E
937
3.5
2.34
E
946
3.5
2.44
E
956
3.0
2.54
E
968
3.0
2.74
E
978
2.5
2.84
E
987
2.5
2.94
E
997
2.0
—
—
—
—
—
—
—
—
—
—
—
—
1.5
2.34
E
960
3.0
2.44
E
969
3.0
2.54
E
979
2.5
2.64
E
988
2.5
2.84
E
997
2.0
2.94
E
1007
2.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
27
Performance data (cont)
50VQP150 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
3800
3900
4000
4100
4200
4300
4400
4500
4600
4700
4800
4900
5000
A
B
bhp
C
D
E
ESP
28
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.44
B
631
6.0
1.54
B
642
5.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.34
B
637
6.0
1.44
B
647
5.5
1.54
B
662
5.0
1.64
B
672
5.0
0.2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.24
B
633
6.0
1.3
B
646
5.5
1.34
B
656
5.5
1.44
B
666
5.0
1.54
B
678
4.5
1.64
B
690
4.0
1.74
B
702
3.5
0.3
—
—
—
—
—
—
—
—
—
—
—
—
1.09
B
631
6.0
1.14
B
640
6.0
1.24
B
653
5.5
1.34
B
666
5.0
1.4
B
678
4.5
1.44
B
687
4.5
1.54
B
697
4.0
1.64
B
708
3.5
1.74
B
720
3.5
1.84
B
731
3.0
0.4
—
—
—
—
1.04
B
639
1.14
6.0
B
651
5.5
1.14
B
661
5.5
1.24
B
673
5.0
1.34
B
685
4.5
1.44
B
697
4.0
1.5
B
706
4.0
1.54
B
715
3.5
1.64
B
727
3.0
1.74
A
738
6.0
1.84
A
749
5.5
1.94
A
760
5.5
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
1.04
1.14
1.24
1.29
1.34
1.44
B
B
B
A
A
A
659
688
718
746
774
802
5.5
4.5
3.5
6.0
5.0
4.5
1.14
1.19
1.24
1.34
1.44
1.54
B
B
B
A
A
A
669
702
729
757
785
811
1.19
1.24
1.34
1.44
1.54
1.64
5.0
4.0
3.0
5.5
5.0
4.0
B
B
A
A
A
A
683
710
739
767
794
821
4.5
4.0
6.0
5.5
4.5
4.0
1.24
1.34
1.44
1.54
1.64
1.69
B
B
A
A
A
A
692
722
750
778
804
831
4.5
3.5
5.5
5.0
4.5
3.5
1.34
1.44
1.54
1.59
1.64
1.74
B
B
A
A
A
A
703
733
761
788
812
838
4.0
3.0
5.5
4.5
4.0
3.5
1.44
1.54
1.59
1.64
1.74
1.84
B
A
A
A
A
A
715
744
771
796
822
847
3.5
6.0
5.0
4.5
4.0
3.0
1.54
1.59
1.64
1.74
1.84
1.94
B
A
A
A
A
A
726
755
782
806
832
857
3.0
5.5
5.0
4.0
3.5
3.0
1.6
1.7
1.8
1.9
2
2.1
A
A
A
A
A
A
735
763
791
817
842
867
6.0
5.5
4.5
4.0
3.5
2.5
1.64
1.74
1.84
1.94
2.04
2.14
A
A
A
A
A
A
744
772
799
825
850
872
6.0
5.0
4.5
3.5
3.0
2.5
1.74
1.84
1.94
2.04
2.14
2.24
A
A
A
A
A
A
755
783
809
835
858
882
5.5
5.0
4.0
3.5
3.0
2.0
1.84
1.94
2.04
2.14
2.24
2.34
A
A
A
A
A
A
766
793
819
844
867
891
5.0
4.5
4.0
3.5
2.5
2.0
1.94
2.04
2.14
2.24
2.34
2.44
A
A
A
A
A
A
777
803
827
852
877
900
5.0
4.5
3.5
3.0
2.5
2.0
2.04
2.14
2.24
2.34
2.44
2.54
A
A
A
A
A
A
785
811
837
862
886
909
4.5
4.0
3.5
3.0
2.0
1.5
1.1
1.54
A
829
4.0
1.64
A
838
1.69
3.5
A
845
3.5
1.74
A
854
3.0
1.84
A
863
3.0
1.94
A
872
2.5
2.04
A
881
2.5
2.2
A
889
2.0
2.24
A
896
2.0
2.34
A
905
1.5
2.44
A
914
1.5
2.54
A
923
1.0
2.64
A
932
1.0
1.2
1.64
A
855
3.0
1.74
A
862
1.74
3.0
A
870
2.5
1.84
A
879
2.5
1.94
A
888
2.0
2.04
A
896
2.0
2.14
A
904
1.5
2.3
A
912
1.5
2.34
A
919
1.0
2.44
A
928
1.0
2.54
C
937
6.0
2.64
C
946
6.0
2.74
C
953
6.0
1.3
1.74
A
879
2.5
1.84
A
887
1.84
2.0
A
895
2.0
1.94
A
904
1.5
2.04
A
912
1.5
2.14
A
919
1.0
2.24
A
927
1.0
2.4
C
935
6.0
2.44
C
942
6.0
2.54
C
951
6.0
2.64
C
959
5.5
2.74
C
966
5.5
2.84
C
975
5.0
1.4
1.84
A
905
2.0
1.94
A
913
1.94
1.5
A
920
1.5
2.04
A
928
1.0
2.14
A
934
1.0
2.24
C
942
6.0
2.34
C
950
6.0
2.5
C
958
6.0
2.54
C
963
5.5
2.64
C
973
5.5
2.74
C
980
5.0
2.84
C
988
5.0
2.94
C
996
4.5
1.5
1.94
A
931
1.0
2.03
A
938
2.04
1.0
C
945
6.0
2.14
C
951
6.0
2.24
C
958
5.5
2.34
C
966
5.5
2.44
C
973
5.5
2.6
C
980
5.0
2.64
C
987
5.0
2.74
C
994
4.5
2.84
C
1001
4.5
2.94
C
1009
4.5
3.04
E
1017
4.5
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
50VQP150 BLOWER PERFORMANCE DATA (cont)
AIRFLOW
(cfm)
5100
5200
5300
5400
5500
5600
5700
5800
5900
6000
6100
6200
6300
A
B
bhp
C
D
E
ESP
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
1.64
B
655
5.5
1.74
B
668
5.0
1.84
B
680
4.5
1.94
B
691
4.0
2.04
B
704
4.0
2.14
B
714
3.5
2.24
B
726
3.0
2.34
A
738
6.0
2.44
A
750
5.5
2.54
A
758
5.5
2.64
A
769
5.0
2.84
A
781
4.5
2.94
A
793
4.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
1.74
B
685
4.5
1.84
B
697
4.0
1.94
B
709
3.5
2.04
B
717
3.5
2.14
A
729
6.0
2.24
A
740
6.0
2.34
A
752
5.5
2.44
A
763
5.0
2.54
A
775
5.0
2.64
A
783
4.5
2.74
A
794
4.5
2.94
A
815
4.0
3.04
D
817
4.0
0.2
1.84
B
714
3.5
1.94
B
726
3.0
2.04
A
737
6.0
2.14
A
745
5.5
2.24
A
756
5.5
2.34
A
767
5.0
2.44
A
779
5.0
2.54
A
788
4.5
2.64
A
799
4.0
2.74
A
808
4.0
2.89
A
819
3.5
3.04
D
830
3.5
3.14
D
841
3.5
0.3
1.94
A
743
6.0
2.04
A
752
5.5
2.14
A
763
5.5
2.24
A
772
5.0
2.34
A
783
4.5
2.44
A
794
4.5
2.54
A
803
4.0
2.64
A
813
4.0
2.74
A
824
3.5
2.89
A
833
3.5
3.04
D
843
3.5
3.14
D
854
3.0
3.29
D
863
3.0
0.4
2.04
A
769
5.0
2.14
A
782
5.0
2.24
A
790
4.5
2.34
A
799
4.5
2.44
A
810
4.0
2.54
A
818
4.0
2.64
A
829
3.5
2.74
A
839
3.5
2.89
A
849
3.0
3.04
D
858
3.0
3.14
D
866
2.5
3.24
D
878
2.5
3.44
D
886
2.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
1.1
2.14
2.24
2.34
2.44
2.54
2.64
2.74
A
A
A
A
A
A
C
798
822
847
872
896
917
940
4.5
4.0
3.0
2.5
2.0
1.5
6.0
2.24
2.34
2.44
2.54
2.64
2.74
2.84
A
A
A
A
A
A
C
806
832
857
882
903
926
949
4.0
3.5
3.0
2.0
1.5
1.0
6.0
2.34
2.44
2.54
2.64
2.74
2.84
2.94
A
A
A
A
A
C
C
817
842
867
889
912
935
957
4.0
3.5
2.5
2.0
1.5
6.0
0.0
2.44
2.54
2.64
2.74
2.84
2.94
3.09
A
A
A
A
A
C
E
825
850
873
897
920
943
965
3.5
3.0
2.5
1.5
1.0
6.0
6.0
2.54
2.64
2.74
2.84
3.09
3.14
3.24
A
A
A
A
D
E
E
836
859
883
907
929
952
972
3.5
3.0
2.0
1.5
1.0
6.0
5.5
2.64
2.74
2.84
3
3.14
3.24
3.34
A
A
A
D
D
E
E
844
868
892
916
938
959
981
3.0
2.5
2.0
1.5
1.0
6.0
5.5
2.74
2.89
3.04
3.14
3.24
3.34
3.44
A
A
D
D
E
E
E
854
878
902
925
948
970
990
3.0
2.0
2.0
1.0
6.0
5.5
5.0
2.84
3
3.14
3.24
3.34
3.44
3.59
A
D
D
D
E
E
E
864
888
911
934
955
977
998
2.5
2.0
1.5
1.0
6.0
5.5
5.0
3.04
3.14
3.24
3.34
3.49
3.64
3.74
D
D
D
E
E
E
E
874
898
921
944
964
986
1007
2.5
2.0
1.5
6.0
5.5
5.0
4.5
3.14
3.24
3.34
3.49
3.64
3.74
3.84
D
D
D
E
E
E
E
880
904
927
950
972
993
1014
2.5
1.5
1.0
6.0
5.5
5.0
4.5
3.24
3.34
3.49
3.64
3.74
3.84
3.99
D
D
D
E
E
E
E
890
913
936
958
980
1000
1021
2.0
1.5
1.0
6.0
5.5
4.5
4.0
3.39
3.54
3.64
3.74
3.89
4.04
4.14
D
D
E
E
E
E
E
900
923
946
968
988
1009
1030
2.0
1.0
6.0
5.5
5.0
4.5
4.0
3.54
3.64
3.79
3.94
4.04
4.14
4.29
D
D
E
E
E
E
E
910
933
955
977
997
1018
1038
1.5
0.0
6.0
5.5
5.0
4.5
4.0
1.2
2.84
C
962
5.5
2.94
C
971
5.5
3.09
E
979
5.5
3.19
E
986
5.0
3.34
E
993
5.0
3.44
E
1002
4.5
3.59
E
1011
4.5
3.74
E
1019
4.5
3.84
E
1027
4.0
3.99
E
1033
4.0
4.14
E
1041
3.5
4.24
E
1050
3.5
4.44
E
1058
3.0
1.3
2.94
C
983
5.0
3.09
E
992
5.0
3.19
E
1000
5.0
3.29
E
1006
4.5
3.44
E
1014
4.5
3.54
E
1023
4.0
3.74
E
1031
4.0
3.84
E
1039
4.0
3.94
E
1046
3.5
4.14
E
1053
3.5
1.24
E
1061
3.0
4.39
E
1070
3.0
4.54
E
1078
2.5
1.4
3.04
E
1005
5.0
3.19
E
1013
4.5
3.29
E
1021
4.5
3.39
E
1026
4.0
3.54
E
1035
4.0
3.69
E
1043
3.5
3.84
E
1051
3.5
3.94
E
1058
3.5
4.09
E
1068
3.0
4.24
E
1073
3.0
4.34
E
1081
2.5
4.54
E
1089
2.5
4.69
E
1097
2.0
1.5
3.19
E
1025
4.5
3.29
E
1032
4.0
3.39
E
1042
4.0
3.49
E
1047
3.5
3.69
E
1055
3.5
3.79
E
1063
3.0
3.94
E
1071
3.0
4.04
E
1077
2.5
4.19
E
1086
2.5
4.34
E
1092
2.5
4.49
E
1099
2.0
4.64
E
1107
2.0
4.84
E
1115
1.5
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
29
Performance data (cont)
50VQP168 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
4200
4400
4600
4800
5000
5200
5400
5600
5800
6000
6200
6400
6600
6800
7000
A
B
bhp
C
D
E
ESP
30
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.98
B
441
6.0
1.08
B
456
6.0
1.26
B
471
5.5
1.28
B
486
5.0
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.88
B
440
6.0
0.98
B
455
6.0
1.06
B
459
5.5
1.08
B
478
5.5
1.28
B
495
5.0
1.38
B
506
4.5
1.48
B
520
4.0
0.2
—
—
—
—
—
—
—
—
—
—
—
—
0.68
B
446
6.0
0.68
B
452
6.0
0.86
B
460
6.0
0.86
B
463
5.5
0.88
B
474
5.5
0.98
B
481
5.0
1.08
B
492
5.0
1.18
B
499
4.5
1.28
B
513
4.0
1.38
B
529
3.5
1.48
B
539
3.5
1.58
B
555
3.0
0.3
0.58
B
457
6.0
0.63
B
467
5.5
0.68
B
476
5.5
0.78
B
485
5.0
0.78
B
495
5.0
0.96
B
500
4.5
0.96
B
504
4.5
0.98
B
510
4.0
1.08
B
517
4.0
1.18
B
526
3.5
1.28
B
533
3.5
1.38
B
549
3.0
1.48
B
561
2.5
1.58
B
574
2.5
1.68
B
586
2.0
0.4
0.68
B
499
5.0
0.68
B
507
4.5
0.78
B
518
4.5
0.88
B
527
4.0
0.88
B
532
4.0
1.06
B
536
3.5
1.06
B
539
3.5
1.08
B
545
3.0
1.18
B
551
3.0
1.28
B
563
2.5
1.38
B
569
2.5
1.48
B
581
2.0
1.66
B
595
2.0
1.68
A
604
6.0
1.88
A
615
6.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
0.74
0.82
0.88
0.98
1.08
1.18
B
B
A
A
A
A
537
577
612
647
678
710
3.5
2.5
6.0
5.5
4.5
3.5
0.78
0.88
0.98
1.08
1.18
1.28
B
B
A
A
A
A
548
584
621
653
684
716
3.5
2.5
6.0
5.0
4.0
3.5
0.88
0.98
1.08
1.18
1.28
1.38
B
B
A
A
A
A
555
590
627
659
692
721
3.0
2.0
5.5
5.0
4.0
3.0
0.98
1.08
1.18
1.28
1.38
1.48
B
B
A
A
A
A
563
600
633
665
697
726
3.0
1.5
5.5
4.5
4.0
3.0
0.98
1.08
1.18
1.28
1.48
1.58
B
B
A
A
A
A
567
604
636
670
700
729
2.5
1.5
5.5
4.5
3.5
3.0
1.16
1.26
1.36
1.46
1.56
1.66
B
A
A
A
A
A
570
606
638
671
701
729
2.5
6.0
5.5
4.5
3.5
2.5
1.18
1.28
1.38
1.48
1.58
1.68
B
A
A
A
A
A
576
609
641
674
703
734
2.5
6.0
5.0
4.5
3.5
2.5
1.28
1.38
1.48
1.58
1.68
1.78
B
A
A
A
A
A
581
613
647
677
706
737
2.0
6.0
5.0
4.0
3.0
2.5
1.28
1.48
1.58
1.68
1.78
1.88
B
A
A
A
A
A
586
618
651
681
710
740
2.0
5.5
4.5
4.0
3.0
2.0
1.38
1.48
1.68
1.78
1.88
2.08
B
A
A
A
A
D
595
628
658
687
718
745
1.5
5.5
4.5
3.5
3.0
2.5
1.48
1.68
1.78
1.88
1.98
2.08
B
A
A
A
A
D
600
633
663
691
722
749
1.5
5.5
4.0
3.5
2.5
2.5
1.68
1.78
1.88
1.98
2.08
2.28
A
A
A
A
D
D
614
644
672
703
730
759
6.0
5.0
4.0
3.5
3.0
2.5
1.78
1.88
1.98
2.08
2.28
2.46
A
A
A
D
D
D
625
656
685
712
741
767
5.5
4.5
4.0
3.5
3.0
2.0
1.88
1.98
2.08
2.28
2.38
2.48
A
A
D
D
D
D
633
664
692
721
747
773
5.5
4.5
4.0
3.0
2.5
2.0
1.98
2.08
2.28
2.46
2.58
2.68
A
D
D
D
D
D
647
674
704
730
756
784
5.0
4.5
3.5
3.0
2.5
1.5
1.1
1.28
A
737
3.0
1.38
A
743
2.5
1.48
A
751
2.5
1.58
A
756
2.5
1.68
A
759
2.0
1.76
A
759
2.0
1.78
A
762
2.0
1.88
A
764
1.5
2.08
D
767
2.0
2.18
D
774
2.0
2.28
D
777
2.0
2.38
D
785
1.5
2.58
D
795
1.5
2.68
D
800
1.0
2.88
D
808
1.0
1.2
1.38
A
764
2.0
1.48
A
772
2.0
1.58
A
777
1.5
1.68
A
783
1.5
1.78
A
786
1.5
1.86
A
786
1.0
1.88
A
788
1.0
2.08
D
793
1.5
2.18
D
795
1.5
2.28
D
800
1.5
2.38
D
803
1.0
2.48
D
810
1.0
2.68
E
820
3.5
2.88
E
825
3.5
2.98
E
835
3.0
1.3
1.48
A
791
1.5
1.58
A
797
1.0
1.68
A
803
1.0
1.78
C
811
4.0
1.88
C
813
4.0
2.06
E
814
4.0
2.08
E
816
4.0
2.18
E
818
4.0
2.28
E
821
3.5
2.38
E
826
3.5
2.48
E
828
3.5
2.68
E
837
3.0
2.88
E
844
3.0
2.98
E
851
2.5
—
—
—
—
1.4
1.58
A
815
1.0
1.68
C
821
3.5
1.78
C
829
3.5
1.88
C
835
3.0
1.98
C
838
3.0
2.16
C
839
3.5
2.18
E
841
3.5
2.24
E
843
3.5
2.38
E
845
3.0
2.48
E
852
3.0
2.68
E
854
3.0
2.78
E
861
2.5
2.98
E
870
2.5
—
—
—
—
—
—
—
—
1.5
1.68
C
838
3.0
1.8
C
847
3.0
1.88
C
853
2.5
1.98
C
858
2.5
2.08
C
864
2.5
2.26
E
865
2.5
2.28
E
867
2.5
2.44
E
869
2.5
2.48
E
872
2.0
2.58
E
876
2.0
2.78
E
878
2.0
2.88
E
887
2.0
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
50VQP192 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
4800
5000
5200
5400
5600
5800
6000
6200
6400
6600
6800
7000
7200
7400
7600
7800
8000
A
B
bhp
C
D
E
ESP
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.98
B
441
6.0
1.08
B
456
6.0
1.26
B
471
5.5
1.28
B
486
5.0
1.48
B
495
4.5
1.58
B
506
4.5
1.68
B
515
4.0
1.78
B
525
4.0
1.88
B
539
3.0
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.88
B
440
6.0
0.98
B
455
6.0
1.06
B
459
6.0
1.08
B
478
5.0
1.28
B
495
5.0
1.38
B
506
4.5
1.48
B
520
4.0
1.58
B
528
4.0
1.68
B
541
3.5
1.78
B
549
3.0
1.88
B
556
2.5
2.08
B
569
2.5
0.2
0.68
B
446
6.0
0.68
B
452
6.0
0.86
B
460
6.0
0.86
B
463
5.5
0.88
B
474
5.5
0.98
B
481
5.0
1.08
B
492
5.0
1.18
B
499
4.5
1.28
B
513
4.5
1.38
B
529
4.0
1.48
B
539
3.5
1.58
B
555
3.0
1.68
B
562
2.5
1.86
B
572
2.5
1.88
B
580
2.0
2.08
B
586
2.0
2.18
B
601
1.5
0.3
0.78
B
485
5.0
0.78
B
495
5.0
0.96
B
500
5.0
0.96
B
504
4.5
0.98
B
510
4.5
1.08
B
517
4.0
1.18
B
526
4.0
1.28
B
533
3.5
1.38
B
549
3.0
1.48
B
561
3.0
1.58
B
574
2.5
1.68
B
586
2.0
1.88
B
593
1.5
1.98
A
605
6.0
2.08
A
611
6.0
2.18
A
617
5.5
2.28
A
629
5.5
0.4
0.88
B
527
4.0
0.88
B
532
4.0
1.06
B
536
3.5
1.06
B
539
3.5
1.08
B
545
3.0
1.18
B
551
3.0
1.28
B
563
2.5
1.38
B
569
2.5
1.48
B
581
2.0
1.66
B
595
2.0
1.68
A
604
6.0
1.88
A
615
6.0
1.98
A
624
6.0
2.08
A
633
5.5
2.26
A
640
5.5
2.28
A
645
5.0
2.48
A
659
4.5
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
0.98
1.08
1.18
1.28
1.38
1.48
B
B
A
A
A
A
563
600
633
665
697
726
3.0
1.5
5.5
4.5
4.0
3.0
0.98
1.08
1.18
1.28
1.48
1.58
B
B
A
A
A
A
567
604
636
670
700
729
2.5
1.5
5.5
4.5
3.5
3.0
1.16
1.26
1.36
1.46
1.56
1.66
B
B
A
A
A
A
570
606
638
671
701
729
2.5
1.5
5.0
4.5
3.5
3.0
1.18
1.28
1.38
1.48
1.58
1.68
B
A
A
A
A
A
576
609
641
674
703
734
2.5
6.0
5.0
4.0
3.5
2.5
1.28
1.38
1.48
1.58
1.68
1.78
B
A
A
A
A
A
581
613
647
677
706
737
2.0
6.0
5.0
4.0
3.5
2.5
1.28
1.48
1.58
1.68
1.78
1.88
B
A
A
A
A
A
586
618
651
681
710
740
2.0
6.0
4.5
4.0
3.0
2.5
1.38
1.48
1.68
1.78
1.88
2.08
B
A
A
A
A
A
595
628
658
687
718
745
1.5
5.5
4.5
3.5
3.0
2.5
1.48
1.68
1.78
1.88
1.98
2.08
B
A
A
A
A
A
600
633
663
691
722
749
1.5
5.5
4.5
3.5
3.0
2.0
1.68
1.78
1.88
1.98
2.08
2.28
A
A
A
A
A
A
614
644
672
703
730
759
6.0
5.0
4.0
3.5
2.5
2.0
1.78
1.88
1.98
2.08
2.28
2.46
A
A
A
A
A
A
625
656
685
712
741
767
6.0
4.5
4.0
3.5
2.5
2.0
1.88
1.98
2.08
2.28
2.38
2.48
A
A
A
A
A
A
633
664
692
721
747
773
5.5
4.5
4.0
3.0
2.5
2.0
1.98
2.08
2.28
2.46
2.58
2.68
A
A
A
A
A
A
647
674
704
730
756
784
5.0
4.5
3.5
3.0
2.0
1.5
2.08
2.28
2.38
2.48
2.68
2.88
A
A
A
A
A
A
652
680
708
734
762
787
5.0
4.0
3.5
3.0
2.0
1.5
2.28
2.38
2.48
2.68
2.88
2.98
A
A
A
A
A
A
661
690
716
744
769
793
4.5
4.0
3.0
2.5
2.0
1.5
2.38
2.48
2.68
2.86
2.98
3.08
A
A
A
A
A
D
667
696
721
749
773
798
4.5
3.5
3.0
2.5
2.0
1.0
2.48
2.68
2.78
2.88
3.08
3.28
A
A
A
A
D
D
674
701
726
753
778
804
4.0
3.5
3.0
2.5
1.5
1.0
2.68
2.88
2.98
3.08
3.28
3.48
A
A
A
D
D
E
685
711
738
763
789
812
4.0
3.0
2.5
2.0
1.5
4.0
1.1
1.58
A
756
2.5
1.68
A
759
2.5
1.76
A
759
2.5
1.78
A
762
2.0
1.88
A
764
2.0
2.08
A
767
2.0
2.18
A
774
2.0
2.28
A
777
1.5
2.38
A
785
1.5
2.58
A
795
1.5
2.68
A
800
1.5
2.88
C
808
3.5
2.98
C
812
4.0
3.08
E
820
4.0
3.28
E
823
3.5
3.38
E
827
3.5
3.58
E
835
3.0
1.2
1.68
A
783
1.5
1.78
A
786
1.5
1.86
A
786
1.0
1.88
A
788
1.0
2.08
A
793
1.5
2.18
A
795
1.5
2.28
A
800
1.5
2.38
A
803
1.0
2.48
A
810
1.0
2.68
C
820
3.5
2.88
C
825
3.5
2.98
C
835
3.0
3.08
E
838
3.0
3.28
E
843
3.0
3.46
E
847
3.0
3.48
E
850
2.5
3.68
E
860
2.5
1.3
1.78
C
811
3.5
1.88
C
813
3.5
2.06
C
814
4.0
2.08
C
816
4.0
2.18
C
818
4.0
2.28
C
821
3.5
2.38
C
826
3.5
2.48
C
828
3.5
2.68
C
837
3.5
2.88
C
844
3.0
2.98
C
851
3.0
3.08
E
858
2.5
3.28
E
861
2.5
3.48
E
868
2.5
3.58
E
872
2.0
3.68
E
875
2.0
3.88
E
882
2.0
1.4
1.88
C
835
3.0
1.98
C
838
3.0
2.16
C
838
3.0
2.18
C
839
3.0
2.24
C
841
3.0
2.28
C
845
3.0
2.48
C
852
3.0
2.68
C
854
3.0
2.78
C
861
2.5
2.98
C
870
2.5
3.08
E
875
2.0
3.28
E
883
2.0
3.48
E
886
2.0
3.58
E
891
1.5
3.68
E
894
1.5
3.88
E
897
1.5
4.08
E
906
1.5
1.5
1.98
C
858
2.5
2.08
C
864
2.5
2.26
C
864
2.5
2.28
C
865
2.5
2.44
C
867
2.5
2.48
C
872
2.5
2.58
C
876
2.0
2.78
C
878
2.0
2.88
C
887
2.0
3.08
E
893
2.0
3.28
E
898
1.5
3.48
E
906
1.5
3.66
E
909
1.5
3.68
E
913
1.0
3.88
E
918
1.0
4.08
E
921
1.0
4.28
E
927
1.0
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest
voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use Dry
Coil to Wet Coil Conversion Table.
31
Performance data (cont)
50VQP240 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
6,000
6,200
6,400
6,600
6,800
7,000
7,200
7,400
7,600
7,800
8,000
A
B
bhp
C
D
E
ESP
32
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.78
B
544
5.5
1.88
B
555
5.0
2.08
B
572
4.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.48
B
530
6.0
1.68
B
544
5.5
1.78
B
561
5.0
1.88
B
575
4.5
2.08
B
589
4.0
2.18
B
601
3.5
0.2
—
—
—
—
—
—
—
—
1.28
B
520
6.0
1.38
B
537
5.5
1.48
B
551
5.5
1.68
B
565
5.0
1.78
B
578
4.5
1.88
B
592
4.0
2.08
B
605
3.5
2.28
B
618
3.0
2.28
B
630
3.0
0.3
1.18
B
529
6.0
1.28
B
542
5.5
1.38
B
556
5.0
1.48
B
570
4.5
1.68
B
583
4.5
1.78
B
596
4.0
1.88
B
608
3.5
2.08
B
621
3.0
2.18
B
633
3.0
2.38
A
646
6.0
2.48
A
657
5.5
0.4
1.28
B
563
5.0
1.38
B
575
4.5
1.48
B
588
4.0
1.68
B
601
4.0
1.78
B
613
3.5
1.88
B
625
3.0
2.08
B
637
2.5
2.28
B
649
2.5
2.28
A
661
5.5
2.48
A
676
5.5
2.68
A
686
5.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
1.38
1.48
1.68
1.78
1.88
2.08
B
B
A
A
A
A
595
626
659
689
717
745
4.0
3.0
6.0
5.0
4.5
4.0
1.48
1.68
1.78
1.88
2.08
2.18
B
B
A
A
A
A
607
637
670
699
726
754
3.5
3.0
5.5
5.0
4.5
3.5
1.68
1.78
1.88
2.08
2.18
2.28
B
A
A
A
A
A
619
649
680
708
736
765
3.5
6.0
5.5
4.5
4.0
3.5
1.78
1.88
2.08
2.18
2.28
2.48
B
A
A
A
A
A
631
662
691
718
745
774
3.0
5.5
5.0
4.5
3.5
3.0
1.88
2.08
2.18
2.28
2.48
2.58
B
A
A
A
A
A
642
674
701
728
754
783
2.5
5.5
5.0
4.0
3.5
3.0
2.08
2.18
2.28
2.48
2.58
2.68
A
A
A
A
A
A
654
684
711
738
766
792
6.0
5.0
4.5
4.0
3.0
2.5
2.18
2.28
2.48
2.68
2.78
2.88
A
A
A
A
A
A
668
695
722
748
776
800
5.5
5.0
4.5
3.5
3.0
2.5
2.38
2.48
2.68
2.78
2.88
3.08
A
A
A
A
A
A
679
706
732
758
785
809
5.5
4.5
4.0
3.5
2.5
2.0
2.48
2.68
2.78
2.88
3.08
3.28
A
A
A
A
A
A
691
717
742
767
794
818
5.0
4.5
4.0
3.0
2.5
2.0
2.68
2.88
2.98
3.08
3.28
3.48
A
A
A
A
A
A
702
728
753
779
803
827
4.5
4.0
3.5
3.0
2.0
1.5
2.88
2.98
3.08
3.28
3.48
3.58
A
A
A
A
A
A
712
737
762
789
812
836
4.5
4.0
3.0
2.5
2.0
1.5
1.1
2.18
A
774
3.5
2.28
A
783
3.0
2.48
A
791
2.5
2.58
A
799
2.5
2.68
A
808
2.0
2.88
A
816
2.0
3.08
A
825
1.5
3.28
A
833
1.5
3.38
A
842
1.0
3.58
A
850
1.0
3.68
C
859
5.5
1.2
2.28
A
801
2.5
2.38
A
809
2.5
2.58
A
817
2.0
2.68
A
824
2.0
2.88
A
833
1.5
3.08
A
841
1.5
3.18
A
849
1.0
3.38
C
857
5.5
3.48
C
867
5.5
3.68
C
875
5.0
3.88
C
883
5.0
1.3
2.38
A
826
2.0
2.48
A
834
1.5
2.68
A
841
1.5
2.88
A
849
1.0
2.98
A
857
1.0
3.18
C
867
5.5
3.28
C
874
5.0
3.48
C
882
5.0
3.68
C
890
5.0
3.88
C
898
4.5
4.08
C
905
4.5
1.4
2.48
A
851
1.0
2.68
A
859
1.0
2.88
C
868
5.5
2.98
C
875
5.0
3.08
C
875
5.0
3.28
C
890
4.5
3.48
C
897
4.5
3.68
C
905
4.5
3.88
C
912
4.0
4.08
C
920
4.0
4.28
C
927
4.0
1.5
2.68
C
877
5.5
2.88
C
884
5.0
3.06
C
891
5.0
3.08
C
898
4.5
3.28
C
898
4.5
3.48
C
913
4.0
3.68
C
920
4.0
3.88
C
927
3.5
4.08
C
934
3.5
4.28
C
941
3.5
4.48
C
948
3.5
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
50VQP240 BLOWER PERFORMANCE DATA (cont)
AIRFLOW
(cfm)
8,200
8,400
8,600
8,800
9,000
9,200
9,400
9,600
8,800
10,000
A
B
bhp
C
D
E
ESP
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
2.28
B
589
4.0
2.48
B
605
3.5
2.58
B
621
3.0
2.78
B
637
2.5
2.98
A
653
6.0
3.18
A
668
5.5
3.48
A
683
5.0
3.68
A
698
4.5
3.88
A
715
4.5
4.08
A
730
4.0
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
2.38
B
617
3.5
2.58
B
633
3.0
2.68
A
649
6.0
2.88
A
664
5.5
3.08
A
679
5.0
3.28
A
694
5.0
3.68
A
711
4.5
3.88
A
725
4.0
4.08
A
739
4.0
4.28
A
753
3.5
0.2
2.48
B
645
2.5
2.68
A
660
5.5
2.88
A
675
5.5
3.08
A
690
5.0
3.28
A
707
4.5
3.48
A
721
4.0
3.78
A
735
4.0
3.98
A
749
3.5
4.28
A
762
3.5
4.48
A
776
3.0
0.3
2.68
A
672
5.5
2.88
A
689
5.0
3.08
A
703
4.5
3.28
A
717
4.5
3.48
A
731
4.0
3.68
A
745
3.5
3.88
A
758
3.5
4.08
A
772
3.0
4.48
A
785
3.0
4.68
A
798
2.5
0.4
2.88
A
700
4.5
3.08
A
714
4.5
3.28
A
728
4.0
3.48
A
742
3.5
3.68
A
755
3.5
3.88
A
768
3.0
4.08
A
782
3.0
4.28
A
795
2.5
4.68
A
810
2.5
4.88
A
822
2.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
2.98
3.08
3.28
3.48
3.68
3.78
A
A
A
A
A
A
726
751
775
801
824
847
4.0
3.5
3.0
2.5
1.5
1.0
3.18
3.28
3.48
3.68
4
4.08
A
A
A
A
A
A
739
763
790
813
836
858
4.0
3.0
2.5
2.0
1.5
1.0
3.38
3.48
3.68
4
4.08
4.28
A
A
A
A
A
C
752
776
802
827
847
869
3.5
3.0
2.5
2.0
1.0
5.5
3.68
3.78
4
4.08
4.28
4.48
A
A
A
A
A
C
766
791
814
836
858
882
3.0
2.5
2.0
1.5
1.0
5.0
3.88
4.08
4.18
4.28
4.48
4.68
A
A
A
A
C
C
779
804
826
848
870
893
3.0
2.5
2.0
1.5
5.5
5.0
4.08
4.28
4.48
4.68
4.78
4.88
A
A
A
A
C
C
791
816
838
860
883
904
2.5
2.0
1.5
1.0
5.0
4.5
4.28
4.48
4.68
4.88
5.08
5.28
A
A
A
C
E
E
806
828
850
871
894
915
2.5
2.0
1.0
5.5
5.0
4.5
4.48
4.68
4.88
5.08
5.28
5.48
A
A
A
E
E
E
819
836
862
883
906
926
2.0
1.5
1.0
5.0
4.5
4.0
4.88
4.98
5.08
5.28
5.48
5.68
A
A
E
E
E
E
831
853
874
896
917
937
1.5
1.0
5.5
4.5
4.5
3.5
5.08
5.28
5.48
5.68
5.88
6.08
E
E
E
E
E
E
844
865
885
908
928
948
6.0
5.5
5.0
4.5
4.0
3.5
1.1
3.88
C
872
5.5
4.18
C
882
5.0
4.48
C
893
5.0
4.68
C
904
4.5
4.88
C
914
4.5
5.08
E
925
4.0
5.38
E
935
4.0
5.68
E
946
3.5
5.88
E
956
3.0
6.28
E
967
3.0
1.2
4.08
C
894
5.0
4.28
C
904
4.5
4.58
C
914
4.5
4.88
C
925
4.0
5.08
E
935
4.0
5.28
E
945
3.5
5.48
E
955
3.5
5.88
E
968
3.0
6.08
E
978
3.0
6.48
E
988
2.5
1.3
4.28
C
915
4.5
4.48
C
925
4.0
4.68
C
935
4.0
4.98
C
945
3.5
5.28
E
955
3.5
5.48
E
967
3.0
5.68
E
977
3.0
6.08
E
987
2.5
6.28
E
997
2.5
6.68
E
1007
2.0
1.4
4.48
C
937
4.0
4.68
C
946
3.5
4.88
C
956
3.5
5.08
E
968
3.0
5.48
E
978
2.5
5.68
E
987
2.5
5.88
E
997
2.0
6.28
E
1007
2.0
6.48
E
1016
2.0
6.78
E
1026
1.5
1.5
4.68
C
960
3.0
4.88
C
969
3.0
5.08
E
979
2.5
5.28
E
988
2.5
5.68
E
997
2.0
5.88
E
1007
2.0
6.08
E
1016
2.0
6.48
E
1025
1.5
6.68
E
1035
1.5
6.88
E
1044
1.0
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
33
Performance data (cont)
50VQP300 BLOWER PERFORMANCE DATA
AIRFLOW
(cfm)
7,600
7,800
8,000
8,200
8,400
8,600
8,800
9,000
9,200
9,400
9,600
9,800
10,000
A
B
bhp
C
D
E
ESP
34
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
2.88
B
631
6.0
3.08
B
642
5.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
2.68
B
637
6.0
2.88
B
647
5.5
3.08
B
662
5.0
3.28
B
672
4.5
0.2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
2.48
B
633
6.0
2.6
B
646
5.5
2.68
B
656
5.5
2.88
B
666
5.0
3.08
B
678
4.5
3.28
B
690
4.0
3.48
B
702
4.0
0.3
—
—
—
—
—
—
—
—
—
—
—
—
2.18
B
631
6.0
2.28
B
640
5.5
2.48
B
653
5.5
2.68
B
666
5.0
2.8
B
678
4.5
2.88
B
687
4.5
3.08
B
697
4.0
3.28
B
708
3.5
3.48
B
720
3.5
3.68
B
731
3.0
0.4
—
—
—
—
2.08
B
639
5.5
2.28
B
651
5.5
2.28
B
661
5.0
2.48
B
673
5.0
2.68
B
685
4.5
2.88
B
697
4.0
3.0
B
706
3.5
3.08
B
715
3.5
3.28
B
727
3.0
3.48
B
738
3.0
3.68
B
749
2.5
3.88
B
760
2.0
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
2.08
2.28
2.48
2.58
2.68
2.88
B
B
B
B
A
A
659
688
718
746
774
802
5.5
4.5
3.5
3.0
6.0
5.0
2.28
2.38
2.48
2.68
2.88
3.08
B
B
B
B
A
A
669
702
729
757
785
811
5.0
4.0
3.0
2.5
5.5
5.0
2.38
2.48
2.68
2.88
3.08
3.28
B
B
B
B
A
A
683
710
739
767
794
821
4.5
3.5
3.0
2.0
5.5
4.5
2.48
2.68
2.88
3.08
3.28
3.38
B
B
B
A
A
A
692
722
750
778
804
831
4.0
3.5
2.5
6.0
5.0
4.5
2.68
2.88
3.08
3.18
3.28
3.48
B
B
B
A
A
A
703
733
761
788
812
838
4.0
3.0
2.0
5.5
5.0
4.0
2.88
3.08
3.18
3.28
3.48
3.68
B
B
A
A
A
A
715
744
771
796
822
847
3.5
2.5
6.0
5.5
4.5
4.0
3.08
3.18
3.28
3.48
3.68
3.88
B
B
A
A
A
A
726
755
782
806
832
857
3.0
2.5
5.5
5.0
4.0
3.5
3.2
3.4
3.6
3.8
4.0
4.2
B
B
A
A
A
A
735
763
791
817
842
867
3.0
2.0
5.5
4.5
4.0
3.0
3.28
3.48
3.68
3.88
4.08
4.28
B
A
A
A
A
A
744
772
799
825
850
872
2.5
6.0
5.0
4.5
3.5
3.0
3.48
3.68
3.88
4.08
4.28
4.48
B
A
A
A
A
A
755
783
809
835
858
882
2.5
5.5
5.0
4.0
3.5
2.5
3.68
3.88
4.08
4.28
4.48
4.68
A
A
A
A
A
A
766
793
819
844
867
891
6.0
5.0
4.5
4.0
3.0
2.5
3.88
4.08
4.28
4.48
4.68
4.88
A
A
A
A
A
A
777
803
827
852
877
900
5.5
5.0
4.5
3.5
2.5
2.0
4.08
4.28
4.48
4.68
4.88
5.08
A
A
A
A
A
D
785
811
837
862
886
909
5.5
4.5
4.0
3.5
2.5
2.0
1.1
3.08
A
829
4.5
3.28
A
838
4.0
3.38
A
845
4.0
3.48
A
854
3.5
3.68
A
863
3.5
3.88
A
872
3.0
4.08
A
881
3.0
4.4
A
889
2.5
4.48
A
896
2.5
4.68
A
905
2.0
4.88
A
914
2.0
5.08
D
923
1.5
5.28
D
932
1.0
1.2
3.28
A
855
3.5
3.48
A
862
3.5
3.48
A
870
3.0
3.68
A
879
3.0
3.88
A
888
2.5
4.08
A
896
2.5
4.28
A
904
2.0
4.6
A
912
2.0
4.68
A
919
1.5
4.88
A
928
1.5
5.08
D
937
1.0
5.28
E
946
3.5
5.48
E
953
3.0
1.3
3.48
A
879
3.0
3.68
A
887
2.5
3.68
A
895
2.5
3.88
A
904
2.0
4.08
A
912
2.0
4.28
A
919
1.5
4.48
A
927
1.5
4.8
A
935
1.0
4.88
A
942
1.0
5.08
E
951
3.5
5.28
E
959
3.0
5.48
E
966
3.0
5.68
E
975
2.5
1.4
3.68
A
905
2.0
3.88
A
913
2.0
3.88
A
920
1.5
4.08
A
928
1.5
4.28
A
934
1.0
4.48
A
942
1.0
4.68
C
950
3.5
5.0
C
958
3.0
5.08
E
963
3.0
5.28
E
973
3.0
5.48
E
980
2.5
5.68
E
988
2.5
5.88
E
996
2.0
1.5
3.88
A
931
1.5
4.06
A
938
1.0
4.08
A
945
1.0
4.28
C
951
3.5
4.48
C
958
3.0
4.68
C
966
3.0
4.88
C
973
2.5
5.2
E
980
2.5
5.28
E
987
2.5
5.48
E
994
2.0
5.68
E
1001
2.0
5.88
E
1009
2.0
6.08
E
1017
2.0
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
50VQP300 BLOWER PERFORMANCE DATA (cont)
AIRFLOW
(cfm)
10,200
10,400
10,600
10,800
11,000
11,200
11,400
11,600
11,800
12,000
12,200
12,400
12,600
A
B
bhp
C
D
E
ESP
—
—
—
—
—
—
—
ESP
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
bhp
Sheave/Motor
rpm
Turns Open
0
3.28
B
655
5.0
3.48
B
668
5.0
3.68
B
680
4.5
3.88
B
691
4.5
4.08
B
704
3.5
4.28
B
714
3.5
4.48
B
726
3.0
4.68
B
738
2.5
4.88
B
750
2.0
5.08
D
758
6.0
5.28
D
769
6.0
5.68
D
781
5.5
5.88
D
793
5.0
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
Standard rpm/Large Motor
High rpm/Large Motor
External Static Pressure
0.1
3.48
B
685
4.5
3.68
B
697
4.0
3.88
B
709
3.5
4.08
B
717
3.5
4.28
B
729
3.0
4.48
B
740
2.5
4.68
B
752
2.0
4.88
A
763
6.0
5.08
D
775
5.5
5.28
D
783
5.5
5.48
D
794
5.0
5.88
D
815
4.5
6.08
D
817
4.5
0.2
3.68
B
714
3.5
3.88
B
726
3.0
4.08
B
737
3.0
4.28
B
745
2.5
4.48
B
756
2.0
4.68
A
767
6.0
4.88
A
779
5.5
5.08
D
788
5.5
5.28
D
799
5.0
5.48
D
808
4.5
5.78
D
819
4.5
6.08
D
830
4.5
6.28
D
841
4.0
0.3
3.88
B
743
2.5
4.08
B
752
2.5
4.28
B
763
2.0
4.48
A
772
6.0
4.68
A
783
5.5
4.88
A
794
5.5
5.08
D
803
5.0
5.28
D
813
4.5
5.48
D
824
4.0
5.78
D
833
4.0
6.08
D
843
4.0
6.28
D
854
3.5
6.58
D
863
3.0
0.4
4.08
A
769
6.0
4.28
A
782
5.5
4.48
A
790
5.5
4.68
A
799
5.0
4.88
A
810
5.0
5.08
D
818
4.5
5.28
D
829
4.5
5.48
D
839
4.0
5.78
D
849
3.5
6.08
D
858
3.5
6.28
D
866
3.0
6.48
D
878
3.0
6.88
D
886
2.5
AIRFLOW (cfm) AT EXTERNAL STATIC PRESSURE (in. wg)
0.5
0.6
0.7
0.8
0.9
1
4.28
4.48
4.68
4.88
5.08
5.28
A
A
A
A
D
D
798
822
847
872
896
917
5.0
4.5
3.5
3.0
2.5
1.5
4.48
4.68
4.88
5.08
5.28
5.48
A
A
A
D
D
E
806
832
857
882
903
926
5.0
4.0
3.5
2.5
2.0
1.5
4.68
4.88
5.08
5.28
5.48
5.68
A
A
D
D
D
D
817
842
867
889
912
935
4.5
4.0
3.0
2.5
2.0
1.0
4.88
5.08
5.28
5.48
5.68
5.88
A
D
D
D
D
E
825
850
873
897
920
943
4.5
3.5
3.0
2.0
1.5
3.5
5.08
5.28
5.48
5.68
6.18
6.28
D
D
D
D
D
E
836
859
883
907
929
952
4.0
3.0
2.5
2.0
1.5
3.5
5.28
5.48
5.68
6
6.28
6.48
D
D
D
D
D
E
844
868
892
916
938
959
3.5
3.0
2.5
1.5
1.0
3.0
5.48
5.78
6.08
6.28
6.48
6.68
D
D
D
D
D
E
854
878
902
925
948
970
3.5
3.0
2.0
1.5
1.0
3.0
5.68
6
6.28
6.48
6.68
6.88
D
D
D
D
E
E
864
888
911
934
955
977
3.0
2.5
2.0
1.0
3.5
2.5
6.08
6.28
6.48
6.68
6.98
7.28
D
D
D
D
E
E
874
898
921
944
964
986
3.0
2.5
2.0
1.0
3.0
2.5
6.28
6.48
6.68
6.98
7.28
7.48
D
D
D
E
E
E
880
904
927
950
972
993
2.5
2.0
1.5
3.5
3.0
2.5
6.48
6.68
6.98
7.28
7.48
—
D
D
D
E
E
—
890
913
936
958
980
—
2.5
2.0
1.5
3.0
2.5
—
6.78
7.08
7.28
7.48
—
—
D
D
D
E
—
—
900
923
946
968
—
—
2.0
1.5
1.0
3.0
—
—
7.08
7.28
—
—
—
—
D
D
—
—
—
—
910
933
—
—
—
—
2.0
1.5
—
—
—
—
1.1
5.48
D
940
1.0
5.68
E
949
3.5
5.88
E
957
3.0
6.18
E
965
3.0
6.48
E
972
3.0
6.68
E
981
2.5
6.88
E
990
2.5
7.18
E
998
2.0
7.48
E
1007
2.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.2
5.68
E
962
3.0
5.88
E
971
3.0
6.18
E
979
2.5
6.38
E
986
2.5
6.68
E
993
2.5
6.88
E
1002
2.0
7.18
E
1011
2.0
7.48
E
1019
1.5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.3
5.88
E
983
2.5
6.18
E
992
2.5
6.38
E
1000
2.0
6.58
E
1006
2.0
6.88
E
1014
2.0
7.08
E
1023
1.5
7.48
E
1031
1.5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.4
6.08
E
1005
2.0
6.38
E
1013
2.0
6.58
E
1021
1.5
6.78
E
1026
1.5
7.08
E
1035
1.0
7.38
E
1043
1.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.5
6.38
E
1025
1.5
6.58
E
1032
1.5
6.78
E
1042
1.0
6.98
E
1047
1.0
7.38
E
1055
0.5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on lowest voltage.
4. Data shown is for wet coil performance. For dry coil performance, calculate the face
velocity of the air coil (face velocity [fpm] = airflow [cfm]/face area [sq ft]), then use
Dry Coil to Wet Coil Conversion Table.
35
Electrical data
ELECTRICAL DATA — STANDARD UNIT
50VQP UNIT
SIZE
084
096
120
150
168
192
240
300
VOLTAGE
(V-Ph-Hz)
MIN/MAX
VOLTAGE
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
COMPRESSOR
BLOWER
OPTION
qty
A, B, C
D,E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
LEGEND
FLA — Full Load Amps
HACR — Heating, Air Conditioning, and Refrigeration
LRA — Locked Rotor Amps
MCA — Minimum Circuit Amps
RLA — Rated Load Amps
NOTES:
1. HACR circuit breaker in U.S.A. only.
2. All fuses Class RK-5.
3. The 460-v units using an internal secondary pump will require a
neutral wire from the supply side in order to feed the accessory
with 265-v.
36
RLA
LRA
23.2
23.2
11.2
11.2
7.9
7.9
25.0
25.0
12.2
12.2
9.0
9.0
30.1
30.1
16.7
16.7
12.2
12.2
48.1
48.1
18.6
18.6
14.7
14.7
23.2
23.2
11.2
11.2
7.9
7.9
25.0
25.0
12.2
12.2
9.0
9.0
30.1
30.1
16.7
16.7
12.2
12.2
48.1
48.1
18.6
18.6
14.7
14.7
164
164
75
75
54
54
164
164
100
100
78
78
225
225
114
114
80
80
245
245
125
125
100
100
164
164
75
75
54
54
164
164
100
100
78
78
225
225
114
114
80
80
245
245
125
125
100
100
FAN
MOTOR
FLA
4.0
5.0
2.0
2.4
1.4
1.9
5.0
6.2
2.4
3.1
1.9
2.3
6.2
9.2
3.1
4.3
2.3
3.4
9.2
14.1
4.3
7.0
3.4
5.2
6.2
9.2
3.1
4.3
2.3
3.4
9.2
14.1
4.3
7.0
3.4
5.2
14.1
21.7
7.0
10.0
5.2
7.7
14.1
21.7
7.0
10.0
5.2
7.7
TOTAL UNIT
FLA
MCA
MAX FUSE/
HACR
27.2
28.2
13.2
13.6
9.3
9.8
30.0
31.2
14.6
15.3
10.9
11.3
36.3
39.3
19.8
21.0
14.5
15.6
57.3
62.2
22.9
25.6
18.1
19.9
52.6
55.6
25.5
26.7
18.1
19.2
59.2
64.1
28.7
31.4
21.4
23.2
74.3
81.9
40.4
43.4
29.6
32.1
110.3
117.9
44.2
47.2
34.6
37.1
33.0
34.0
16.0
16.4
11.3
11.8
36.3
37.5
17.6
18.4
13.1
13.6
43.8
46.8
24.0
25.2
17.5
18.6
69.3
74.2
27.6
30.3
21.8
23.6
58.4
61.4
28.3
29.5
20.1
21.2
65.4
70.3
31.8
34.5
23.6
25.5
81.8
89.4
44.6
47.6
32.6
35.1
122.3
129.9
48.9
51.9
38.3
40.8
50
50
25
25
15
15
60
60
25
30
20
20
70
70
40
40
25
30
110
110
45
45
35
35
80
80
35
40
25
25
90
90
40
45
30
30
110
110
60
60
40
45
150
175
60
70
50
50
ELECTRICAL DATA — DUAL POINT POWER UNIT
COMPRESSOR
50VQP UNIT
SIZE
084
096
120
150
168
192
240
300
VOLTAGE
MIN/MAX
VOLTAGE
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
208/230-3-60
197/254
460-3-60
414/506
575-3-60
518/633
BLOWER
OPTION
qty
RLA
LRA
FLA
MCA
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
A, B, C
D, E
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
23.2
23.2
11.2
11.2
7.9
7.9
25.0
25.0
12.2
12.2
9.0
9.0
30.1
30.1
16.7
16.7
12.2
12.2
48.1
48.1
18.6
18.6
14.7
14.7
23.2
23.2
11.2
11.2
7.9
7.9
25.0
25.0
12.2
12.2
9.0
9.0
30.1
30.1
16.7
16.7
12.2
12.2
48.1
48.1
18.6
18.6
14.7
14.7
164
164
75
75
54
54
164
164
100
100
78
78
225
225
114
114
80
80
245
245
125
125
100
100
164
164
75
75
54
54
164
164
100
100
78
78
225
225
114
114
80
80
245
245
125
125
100
100
23.2
23.2
11.2
11.2
7.9
7.9
25.0
25.0
12.2
12.2
9.0
9.0
30.1
30.1
16.7
16.7
12.2
12.2
48.1
48.1
18.6
18.6
14.7
14.7
46.4
46.4
22.4
22.4
15.8
15.8
50.0
50.0
24.4
24.4
18.0
18.0
60.2
60.2
33.4
33.4
24.4
24.4
96.2
96.2
37.2
37.2
29.4
29.4
29.0
29.0
38.0
38.0
9.9
9.9
31.3
31.3
15.3
15.3
11.3
11.3
37.6
37.6
20.9
20.9
15.3
15.3
60.1
60.1
23.3
23.3
18.4
18.4
52.2
52.2
25.2
25.2
17.8
17.8
56.3
56.3
27.4
27.4
20.3
20.3
67.7
67.7
37.6
37.6
27.4
27.4
108.2
108.2
41.9
41.9
33.1
33.1
MAX
FUSE/
HACR
50
50
25
25
15
15
50
50
25
25
20
20
60
60
35
35
25
25
100
100
40
40
30
30
70
70
35
35
25
25
80
80
35
35
25
25
90
90
50
50
35
35
150
150
60
60
45
45
EMERGENCY POWER SUPPLY
MAX
TOTAL
MCA
FUSE/
UNIT FLA
HACR
4.0
5.0
15
5.0
6.3
15
2.0
2.5
15
2.4
3.0
15
1.4
1.8
15
1.9
2.4
15
5.0
6.3
15
6.2
7.8
15
2.4
3.0
15
3.1
3.9
15
1.9
2.4
15
2.3
2.9
15
6.2
7.8
15
9.2
11.5
20
3.1
3.9
15
4.3
5.4
15
2.3
2.9
15
3.4
4.3
15
9.2
11.5
20
14.1
17.6
30
4.3
5.4
15
7.0
8.8
15
3.4
4.3
15
5.2
6.5
15
6.2
7.8
15
9.2
11.5
20
3.1
3.9
15
4.3
5.4
15
2.3
2.9
15
3.4
4.3
15
9.2
11.5
20
14.1
17.6
30
4.3
5.4
15
7.0
8.8
15
3.4
4.3
15
5.2
6.5
15
14.1
17.6
30
21.7
27.1
45
7.0
8.8
15
10.0
12.5
20
5.2
6.5
15
7.7
9.6
15
14.1
17.6
30
21.7
27.1
45
7.0
8.8
15
10.0
12.5
20
5.2
6.5
15
7.7
9.6
15
LEGEND
FLA
— Full Load Amps
HACR — Heating, Air Conditioning, and Refrigeration
LRA
— Locked Rotor Amps
MCA — Minimum Circuit Amps
RLA
— Rated Load Amps
NOTES:
1. HACR circuit breaker in U.S.A. only.
2. All fuses Class RK-5.
3. The 460-v units using an internal secondary pump will require a neutral wire
from the supply side in order to feed the accessory with 265-v.
37
Typical piping and wiring
50VQP
Supply Air
Optional Discharge
Optional Discharge
Supply Air
Supply Water
Return
Water
24 V Remote
Mtd. Stat
T
Balancing
Valve
Condensate
Water In
Water Out
Unions
Valves
Access
Panel
Access
Panel
Access
Panel
Access
Panel
Power
Supply
Control Box
Trap
Vibration
Pad
Condensate
NOTES:
1. Wiring and piping are general guides only. They are not intended for or to include all details for a specific installation.
2. Return air ductwork can be field installed if desired. See base unit dimensions for return air duct pilot hole locations.
3. All wiring must comply with applicable local and national codes.
4. All piping must follow standard refrigerant piping techniques. Refer to Carrier System Design Manual, Part 3, for details.
5. For maximum working pressure, see installation instructions.
38
Disconnect
Switch or
Per Local Codes
Typical control wiring schematics
50VQP084-168 WITH COMPLETE C CONTROL (TYPICAL)
A50-8438
Complete C
LEGEND
AL
BC
CB
CC
CO
DPP
FP1
FP2
HP
JW3
LOC
PDB1
PDB2
RVS
TRANS
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Alarm Relay
Blower Contactor
Circuit Breaker
Compressor Contactor
Sensor, Condensate Overflow
Dual Point Power
Sensor, Water Coil Freeze Protection
Sensor, Air Coil Freeze Protection
High-Pressure Switch
Clippable Field Selection Jumper
Loss of Charge Pressure Switch
Power Distribution Block
Power Distribution Block Dual Point Option
Reversing Valve Solenoid
Transformer
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC (National Electrical
Code) and local codes.
3. 208/230-v transformers will be connected for 208-v operation. For
230-v operation, disconnect RED lead at L1, and attach ORG
lead to L1. Close open end of RED lead with insulating tape.
4. FPI jumper provides low temperature protection for WATER.
When using ANTIFREEZE solutions, cut JW3 jumper.
5. Typical heat pump thermostat wiring shown. Refer to thermostat
installation instructions for wiring to the unit. Thermostat wiring
Factory Line Voltage Wiring
Factory Low Voltage Wiring
Field Line Voltage Wiring
Field Low Voltage Wiring
Printed Circuit Trace
Optional Wiring
Relay/Contactor Coil
Ground
Solenoid Coil
Relay Contacts - N.O.
Relay Contacts - N.C.
Temperature Switch
Switch - Low Pressure
Thermistor
Switch - High Pressure
Condensate Pan
Wire Nut
Circuit Breaker
must be “Class 1” and voltage rating equal to or greater than unit
supply voltage.
6. 24-v alarm signal shown. For dry alarm contact, cut JW1 jumper
and dry contact will be available between AL1 and AL2.
7. Transformer secondary ground via Complete C board standoffs
and screws to control box. (Ground available from top two standoffs as shown.)
8. For dual point power option, blower wires (3 qty) will go to PDB2
only.
39
Typical control wiring schematics (cont)
50VQP084-168 WITH DELUXE D CONTROL (TYPICAL)
Deluxe D
a50-8439
Deluxe D
LEGEND
AL
BC
CB
CC
CO
DPP
FP1
FP2
HP
JW3
LOC
PDB1
PDB2
RVS
TRANS
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Alarm Relay
Blower Contactor
Circuit Breaker
Compressor Contactor
Sensor, Condensate Overflow
Dual Point Power
Sensor, Water Coil Freeze Protection
Sensor, Air Coil Freeze Protection
High-Pressure Switch
Clippable Field Selection Jumper
Loss of Charge Pressure Switch
Power Distribution Block
Power Distribution Block Dual Point Option
Reversing Valve Solenoid
Transformer
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC (National Electrical
Code) and local codes.
3. 208/230-v transformer will be connected for 208-v operation. For
230-v operation, disconnect RED lead at L1, and attach ORG
lead to L1. Insulate open end of RED lead with insulating tape.
4. FP1 thermistor provides freeze protection for WATER. When
using ANTIFREEZE solution, cut JW3 jumper.
5. Typical heat pump thermostat wiring shown. Refer to thermostat
installation instructions for wiring to the unit. Thermostat wiring
must be “Class 1” and voltage rating equal to or greater than unit
supply voltage.
40
Factory Line Voltage Wiring
Factory Low Voltage Wiring
Field Line Voltage Wiring
Field Low Voltage Wiring
Printed Circuit Trace
Optional Wiring
Relay/Contactor Coil
Ground
Solenoid Coil
Relay Contacts - N.O.
Relay Contacts - N.C.
Temperature Switch
Switch - Low Pressure
Thermistor
Switch - High Pressure
Condensate Pan
Wire Nut
Circuit Breaker
6. 24-v alarm signal shown. For dry alarm contact, cut AL2 DRY
(JW4) jumper and dry contact will be available between AL1 and
AL2.
7. Transformer secondary ground via Deluxe D board standoffs and
screws to control box. (Ground available from top two standoffs
as shown.)
8. For dual point power option, blower wires (3 qty) will go to PDB2
only.
50VQP084-300 UNITS WITH COMPLETE C AND LON CONTROLLER (460 V)
a50-8417
Complete C
LEGEND
AL
— Alarm Relay Contacts
BM
— Blower Motor
BMC — Blower Motor Capacitor
BR
— Blower Relay
CAP — Compressor Capacitor
CB
— Circuit Breaker
CC
— Compressor Contactor
CO
— Sensor, Condensate Overflow
FP1
— Sensor, Low Temperature Protection, Water Coil
FP2
— Sensor, Low Temperature Protection, Air Coil
HP
— High-Pressure Switch
HPWS — High-Pressure Water Switch
JW1
— Clippable Field Selection Jumper
LOC — Loss of Charge Pressure Switch
LON — Local Operating Network
MV
— Motorized Valve
MVES — Motorized Valve End Switch
*Optional Wiring.
NEC
P1
RVS
TRANS
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC and local codes.
3. Transformer is wired to 460 v BLK/RED lead for 460-3-60 units.
Transformer is energy limiting or may have circuit breaker.
4. FP1 thermistor provides low temperature protection for water.
When using antifreeze solutions, cut JW3 jumper.
5. Refer to microprocessor control, LON, or thermostat installation instructions for wiring to the unit. Wire “N01” from LON to
“Y1” Complete C when a motorized valve is not used. Low voltage wiring must be Class 1 and voltage rating equal to or
greater than unit supply voltage.
6. Factory cut JW1 jumper. Dry contact will be available between
AL1 and AL2.
7. Transformer secondary ground via green wire with yellow strip
from “C” terminal to control box.
8. Fan motors are factory wired for medium speed. For high or low
speed, remove BLU wire from fan motor speed tap “M” and
connect to “H” for high speed or “L” for low speed.
—
—
—
—
National Electrical Code
Field Wiring Terminal Block
Reversing Valve Solenoid
Transformer
Field Line Voltage Wiring
Field Low Voltage Wiring
Printed Circuit Trace
Optional Wiring
Relay/Contactor Coil
Thermistor
Ground
Wire Nut
Relay Contacts - N.C.
Relay Contacts - N.O.
Low Pressure Switch
High Pressure Switch
Condensate Pan
Splice Cap
Solenoid Coil
Circuit Breaker
Temperature Switch
9. For low speed, remove BLK wire from BR “6” and replace with
RED. Connect BLK and BRN wires together.
10. Optional LON wires. Only connect if LON connection is desired
at the wall sensor.
11. For blower motors with leads. For medium or low speed,
disconnect BLK wire from BR “6”. Connect BLK and ORG/PUR
wire together. Connect RED for low or BLU for medium to
BR “6”.
12. Blower motor factory wired to medium speed. For low speed
remove BLU wire from medium tap and connect to low speed
tap. For high speed, remove BLU wire from exisiting speed tap
and remove BRN jumper wire from high speed tap. Connect
BLU wire to high speed tap. Tape off unconnected end of BRN
jumper.
13. The 460-v units using an internal secondary pump will require
a neutral wire from the supply side in order to feed the accessory with 265-v.
41
Typical control wiring schematics (cont)
50VQP084-300 UNITS WITH DELUXE D AND LON CONTROLLER (460 V)
Deluxe D
a50-8418
LEGEND
AL
— Alarm Relay Contacts
BM
— Blower Motor
BMC — Blower Motor Capacitor
BR
— Blower Relay
CAP — Compressor Capacitor
CB
— Circuit Breaker
CC
— Compressor Contactor
CO
— Sensor, Condensate Overflow
FP1
— Sensor, Low Temperature Protection, Water Coil
FP2
— Sensor, Low Temperature Protection, Air Coil
HP
— High-Pressure Switch
HPWS — High-Pressure Water Switch
JW1
— Clippable Field Selection Jumper
LOC — Loss of Charge Pressure Switch
LON — Local Operating Network
MV
— Motorized Valve
MVES — Motorized Valve End Switch
*Optional Wiring.
NEC
P1
RVS
TRANS
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC and local codes.
3. Transformer is wired to 460-v BLK/RED lead for 460-3-60
units. Transformer is energy limiting or may have circuit
breaker.
4. FP1 thermistor provides low temperature protection for water.
When using antifreeze solutions, cut JW3 jumper.
5. Refer to microprocessor control, LON, thermostat installation
instructions for wiring to the unit. Wire “N01” from LON to “Y1”
Deluxe D when motorized valve is not used. Thermostat wiring
must be Class 1 and voltage rating equal to or greater than
unit supply voltage.
6. Factory cut JW4 jumper. Dry contact will be available between
AL1 and AL2.
42
—
—
—
—
National Electrical Code
Field Wiring Terminal Block
Reversing Valve Solenoid
Transformer
Field Line Voltage Wiring
Field Low Voltage Wiring
Printed Circuit Trace
Optional Wiring
Relay/Contactor Coil
Thermistor
Ground
Wire Nut
Relay Contacts - N.C.
Relay Contacts - N.O.
Low Pressure Switch
High Pressure Switch
Condensate Pan
Splice Cap
Solenoid Coil
Circuit Breaker
Temperature Switch
7. Transformer secondary ground via green wire with yellow
stripe from “C” terminal to control box.
8. Blower motor is factory wired for medium and high speeds. For
any other combination of speeds, attach black wire to the
higher of the two desired speed taps at the motor, and attach
the blue wire to the lower of the two desired speed taps.
9. Blower motor is factory wired for high and low speeds. No other
combination is available.
10. Optional LON wires. Only connect if LON connection is desired
at the wall sensor.
11. The 460-v units using an internal secondary pump will require
a neutral wire from the supply side in order to feed the accessory with 265-v.
50VQP UNIT WITH COMPLETE C AND WSHP OPEN CONTROLLER (208/230 V)
Complete C
LEGEND
AL
— Alarm Relay Contacts
ASTAT — Aquastat
BM
— Blower Motor
BMC
— Blower Motor Capacitor
BR
— Blower Relay
CAP
— Compressor Capacitor
CB
— Circuit Breaker
CC
— Compressor Contactor
CO
— Sensor, Condensate Overflow
DTS
— Discharge Temperature Switch
ECM
— Electronically Commutated Motor
FP1
— Sensor, Low Temperature Protection, Water Coil
FP2
— Sensor, Low Temperature Protection, Air Coil
HP
— High-Pressure Switch
HPWS — High-Pressure Water Switch
HWG — Hot Water Gage
JW1
— Clippable Field Selection Jumper
LOC
— Loss of Charge Pressure Switch
LWT
— Leaving Water Temperature
*Optional Wiring.
MV
MVES
NEC
P1
RVS
TRANS
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC and local codes.
3. 208/230-v units are wired for 208-v operation. For 230-v operation, switch RED wire to ORG wire. Transformer is energy limiting
or may have circuit breaker.
4. FP1 thermistor provides low temperature protection for water.
When using antifreeze solutions, cut JW3 jumper.
5. Refer to thermostat installation instructions for control wiring to
the unit. Wire ECM to Y Complete C when a motorized valve is
—
—
—
—
—
—
Motorized Valve
Motorized Valve End Switch
National Electrical Code
Field Wiring Terminal Block
Reversing Valve Solenoid
Transformer
Factory Low Voltage Wiring
Factory Line Voltage Wiring
Field Line Voltage Wiring
Field Low Voltage Wiring
Printed Circuit Trace
Optional Wiring
Relay/Contactor Coil
Condensate Pan
Temperature Switch
Thermistor
Ground
Wire Nut
Relay Contacts - N.C.
Relay Contacts - N.O.
Low Pressure Switch
High Pressure Switch
Splice Cap
Circuit Breaker
Solenoid Coil
not used. Thermostat wiring must be Class 1 and voltage rating
equal to or greater than unit supply voltage.
6. 24-v alarm signal shown. For dry alarm contact, cut JW1 jumper.
Dry contact will be available between AL1 and AL2.
7. Transformer secondary ground via green wire with yellow stripe
from “C” terminal to control box.
8. Aquastat is supplied with unit and must be wired in series with the
hot leg to the pump. Aquastat is rated for voltages up to 277-v.
43
Typical control wiring schematics (cont)
PREMIERLINK™ CONTROLLER APPLICATIONS WITH COMPLETE C CONTROL
COMPLETE
C
CONTROL
PREMIER
LINK
PWR
Y
HS1/EXH/RVS
W
CR
CR
O
G
R
LEGEND
CR — Control Relay
LWT — Leaving Water Temperature Sensor
SAT — Supply Air Temperature Sensor
SPT — Space Temperature Sensor
NOTE: Reversing valve is on in Cooling
mode.
C
CMP1
FAN
AL2
PWR
J1
J8
AL1
A
J5
J6
S
A
T
CMPSAFE
S
P
T
J4
L
W
T
PREMIERLINK CONTROLLER APPLICATIONS WITH DELUXE D CONTROL
PREMIER
LINK
PWR
DELUXE
D
CONTROL
Y1
HS2
Y2
HS1
LEGEND
LWT — Leaving Water Temperature Sensor
SAT — Supply Air Temperature Sensor
SPT — Space Temperature Sensor
NOTE: Reversing valve is on in Cooling
mode.
W1
O/W2
CMP2
G
CMP1
FAN
C
PWR
J1
J8
R
J5
J6
44
S
A
T
L
W
T
J4
CMPSAFE
S
P
T
AL1
WSHP OPEN CONTROL
RED
+ 24vac
Condensate
Overflow Switch
WHT
BRN
- Gnd
Fan (DO-1) (Fan On or Low Speed)
GRN
PINK
SPACE RH
SENSOR
SPACE CO2
SENSOR
+24vac
+24vac
+
Aux Heat (DO-2)
ORN
YLW
Reversing Valve (DO-3)
Comp #2 (DO-4)
BLU
Comp #1 (DO-5)
RED
BLU
+
4-20mA
Comp Status (DI-5) (If not installed, it must be connected to DO-5)
LWT (Input 6)
ORN
BRN
PINK
4-20mA
-
-
SAT (LAT) (Input 7)
VIO
FIELD INSTALLED (OPTIONAL) – SEE NOTE 2
AO1 – Aux Reheat or Cond.
WTR. Loop Econ. (AO 1)
PINK
J1
(DI-3/Dry Contact)
J2
1
1
10
7
1
2
4
3
5
6
J4
1
a50-8380
2
3
4
5
6
7
8
J5
1
2
OA DAMPER (AO-2)
J11
8
J22
7
DEHUMIDIFY OUTPUT CONTACT (DO-6) (FACTORY OPTION)
6
Field Installed
Local Access Port
4
4
4
3
5
3
2
3
WHITE
GREEN
2
2
FAN SPEED (DO-8) (HIGH OR FAN ON )
1
1
8
7
6
4
8
3
3
To
SPT PLUS
2
7
9 0 1
2
4
5
RED
BLACK
1
9 0 1
6
FAN SPEED (DO-7) (MED OR LOW)
5
J12
LSB
MSB
J13
MSTP Baud
9600 19.2k 38.4k 76.8k
J17
FIELD INSTALLED
SPT PLUS Sensor
Shown
SW3
1
2
J14
3
J19
1
2
3
4
O
N
1
2
3
4
5
6
7
8
RED
BLACK
WHITE
GREEN
+12V
Rnet+
Gnd
DB
LED1
012207-1BT485BT
NOTES:
1. Mount the water source heat pump controller in the equipment
controls enclosure with at least two #6 x 1 in. self-tapping
screws. Allow adequate clearance for wiring.
2. Verify sensor power and wiring requirements prior to making
any terminations. Sensors requiring a separate isolated 24 vac
power source will not utilize WSHP terminals J4-1, or 4.
To WSHP Controller
Rnet Terminals (J13)
LEGEND
Factory Wiring
Field Wiring
Rnet-
J20
Install BT485 where device is
located at the end of network
segment only.
45
Application data
Aquazone™ water source heat pump products are available
in a flexible, efficient array of models, which can be used in
all types of water loop, ground water, and ground loop
type systems. Utilize Aquazone products to provide optimal energy efficient solutions and adapt to the most challenging design requirements.
AQUAZONE PRODUCT GUIDE
50 SERIES
50HQP,VQP
50PC
50PS
50PEC
50PT
50PSW
50RTG
50VS
TYPE
SIZE (tons)
Large Capacity
6-10 (HQP)
7-25 (VQP)
APPLICATION
Environmentally sound unit with Puron®
refrigerant (R-410A) designed to handle
large zoned areas for all geothermal and
boiler/tower applications.
Compact
Compact WSHP with Puron refrigerant
11/4-5
(R-410A) for boiler/tower, ground water, or
ground loop systems.
Premium
Premium, ultra efficient unit with Puron
Efficiency
refrigerant (R-410A) for new boiler/tower,
1/ -6
ground water, or ground loop systems.
2
High Efficiency Efficient console unit with Puron refrigerant
(R-410A) and attractive design for finished
Console
3/ -11/
interior, under-window installations.
4
2
Premium, ultra efficient 2-stage unit with
Premium
Puron refrigerant (R-410A) for new boiler/
Efficiency
2-6
tower, ground water, or ground loop
systems.
Water-to-Water Efficient unit with Puron refrigerant
3-30
(R-410A) serves as an alternative to preheat or cool air. Unit can be used as a
stand-alone or supplemental boiler/chiller
in most hydronic heating applications. Also
conditions process fluids, lubricants, and
refrigerants.
Rooftop
Economical solution for indoor air quality
3-20
(IAQ) problems and tempering ventilation
air.
Premium EffiUltra efficient unit with environmentally
ciency Vertical sound Puron refrigerant (R-410A) for
Stack Heat Pump boiler/tower and geothermal applications
3/ to 3 Tons
(condominiums, hotels, etc.). Stacked
4
design allows for common piping and simplistic design.
Water loop system
Water loop (or boiler/tower) system applications typically
include a number of units plumbed to a common piping
system. For optimal performance, this system should be
designed between 2.25 and 3 gpm per ton of cooling capacity. The system is comprised of highly efficient packaged reverse cycle heat pump units interconnected by a
water loop. The water circuit serves as both a sink and
source for heat absorption and rejection and is designed
for entering water temperatures between 60 F and 90 F.
Within this temperature range units can heat or cool as required from the same water source. Transferring heat from
warm to cold spaces in the building, whenever they coexist, conserves energy rather than creating new heat.
Refer to the Carrier Water Source Heat Pump System Design Guide for assistance with the design of water
loop systems. The guide includes a practical approach for
the latest and most current design recommendations
including:
• Product application including horizontal, vertical, console, rooftop and water-to-water applications.
• Ventilation methods and system design including energy
recovery.
• Acoustical considerations for different product types.
• Addressing indoor air quality (IAQ) issues such as condensate removal, humidity control.
46
• Air distribution design including diffuser selection/
layout and ductwork design.
• Hydronic system design including pipe sizing/layout
and boiler/tower sizing.
• Control configurations such as stand alone, DDC, DCV,
and VVT® controls.
• WSHP Efficiency/Operational Cost Comparison chart.
• System variations such as a system without a boiler,
variable pumping, and VAV for interior use.
Ground water systems
To utilize Aquazone units in ground water applications, extended range should be specified. This will provide factoryinstalled insulation on the coaxial coil to prevent condensate from dripping when entering water temperatures are
below 60 F. In addition, the copper coaxial coil installed on
the Aquazone units may not be suitable for all water conditions. Refer to the Water Conditioning section for proper
coaxial coil material selection.
Surface water system — This system is typically located
near a lake or pond. In this application, the loop can be
submerged in a series of coils beneath the water surface.
The number of coils required depends on system load and
design. This application requires minimum piping and
excavation.
Open loop system — This system is used where ground
water is plentiful. In this application, ground water is
pumped through supply piping from the well to the building.
The water is then pumped back into the ground through a
discharge well as it leaves the building. An additional heat
exchanger is usually installed between the building water
piping system and the ground water piping system. This design limits the amount of piping and excavation required.
Aquazone units are provided with a standard TXV and
are rated to extremely low temperatures to self-adjust the
refrigeration circuit, therefore water regulating valves are
not required on open loop systems. To conserve water on
this type of system, a slow opening/closing solenoid valve
is recommended.
Ground loop systems
There are many commonly specified designs for ground
loop applications. Typical designs include vertical loops
and horizontal loops. In some applications, water is piped
from the ground or lake directly to the water source heat
pump. Piping is limited to the amount of pipe required to
get the water from the source to the unit.
NOTE: When utilizing Aquazone water source heat pumps
in ground loop systems, refer to design considerations in
the ground water system section.
Horizontal ground loop — This system is used when
adequate space is available and trenching can be easily accomplished. A series of parallel pipes are laid out in trenches 3 to 6 feet below the ground surface, and then backfilled. Often, multiple pipes are used to maximize the heat
transfer capability of each trench. The amount of pipe and
the size of the ground loop field are based on ground
conditions, heating, and cooling requirements of the application and system design.
Vertical ground loop — This system is used in vertical
borehole applications. This design is well suited for retrofit
applications when space is limited or where landscaping is
already complete and minimum disruption of the site is desired. The vertical ground loop system contains a single
loop of pipe inserted into a hole. The hole is back-filled and
grouted after the pipe is inserted. The completed loop is
concealed below ground. The number of loops required depends on ground conditions, heating and cooling requirements, and the depth of each hole.
Hybrid systems — In some applications, it may be beneficial to incorporate a cooling tower into the ground loop
system to reduce the overall cost. A hybrid system discards
excess heat into the air and increases the cooling performance of the ground loop.
Condensate drainage
Venting — Condensate lines should be properly vented to
prevent fan pressure from causing water to hang up in the
piping. Condensate lines should be pitched to assure full
drainage of condensate under all load conditions. Chemical
treatment should be provided to remove algae in the condensate pans and drains in geographical areas that are
conducive to algae growth.
Trapping — Condensate trapping is an essential necessity
on every water source heat pump unit. A trap is provided
to prevent the backflow of moisture from the condensate
pan and into the fan intake or downstream into the mechanical system. The water seal or the length of the trap
depends on the positive or negative pressure on the drain
pan. As a rule of thumb, the water seal should be sized for
1 in. for every 1 in. of negative pressure on the unit. The
water seal is the distance from the bottom of the unit condensate piping connection to the bottom of the condensate
drain line run-out piping. Therefore, the trap size should be
double the water seal dimension.
Each unit must be installed with its own individual trap,
vent, and means to flush or blowout the condensate drain
lines. Do not install units with a common trap or vent.
Water conditioning
In some applications, maintaining proper water quality
may require the use of higher corrosion protection for
the water-to-refrigerant heat exchanger. Water quality varies from location to location and is unique for each job.
Water characteristics such as pH value, alkalinity, hardness, and specific conductance are of importance when
considering any WSHP application. Water typically includes impurities and hardness that must be removed. The
required treatment will depend on the water quality as well
as type of system. Water problems fall into three main
categories:
1. Scale formation caused by hard water reduces the
heat transfer rate and increases the water pressure
drop through the heat exchanger. As water is heated,
minerals and salts are precipitated from a solution
and deposited on the inside surface of the pipe or
tube.
2. Corrosion is caused by absorption of gases from the
air coupled with water on exposed metal. Corrosion
is also common in salt-water areas.
3. Organic growths such as algae can reduce the heat
transfer rate by forming an insulating coating on the
inside tube surface. Algae can also promote corrosion
by pitting.
NOTE: In most commercial water loop applications, Aquazone™ WSHP units use copper water-to-refrigerant heat
exchanger. Units can also be equipped with a cupronickel
heat exchanger for applications where water is outside the
standard contaminant limits for a copper heat exchanger.
47
Application data (cont)
WATER QUALITY GUIDELINES
CONDITION
HX MATERIAL*
CLOSED
RECIRCULATING†
OPEN LOOP AND RECIRCULATING WELL**
Scaling Potential — Primary Measurement
Above the given limits, scaling is likely to occur. Scaling indexes should be calculated using the limits below.
pH/Calcium
All
N/A
pH < 7.5 and Ca Hardness, <100 ppm
Hardness Method
Index Limits for Probable Scaling Situations (Operation outside these limits is not recommended.)
Scaling indexes should be calculated at 150 F for direct use and HWG applications, and at 90 F for indirect HX use. A monitoring plan should be implemented.
Ryznar Stability Index
6.0 - 7.5
All
N/A
If >7.5 minimize steel pipe use.
Langelier Saturation Index
–0.5 to +0.5
All
N/A
If <–0.5 minimize steel pipe use.
Based upon 150 F HWG and direct well, 85 F indirect well HX.
Iron Fouling
Iron Fe2+ (Ferrous)
<0.2 ppm (Ferrous)
All
N/A
(Bacterial Iron Potential)
If Fe2+ (ferrous) >0.2 ppm with pH 6 - 8, O2<5 ppm check for iron bacteria.
Iron Fouling
<0.5 ppm of Oxygen
All
N/A
Above this level deposition will occur.
Corrosion Prevention††
pH
6 - 8.5
6 - 8.5
All
Monitor/treat as needed.
Minimize steel pipe below 7 and no open tanks with pH <8.
<0.5 ppm
Hydrogen Sulfide (H2S)
At H2S>0.2 ppm, avoid use of copper and cupronickel piping or HXs.
All
N/A
Rotten egg smell appears at 0.5 ppm level.
Copper alloy (bronze or brass) cast components are okay to <0.5 ppm.
Ammonia Ion as Hydroxide,
<0.5 ppm
Chloride, Nitrate and Sulfate
All
N/A
Compounds
Maximum Chloride Levels
Maximum allowable at maximum water temperature.
50 F (10 C)
75 F (24 C)
100 F (38 C)
Copper
N/A
<20 ppm
NR
NR
Cupronickel
N/A
<150 ppm
NR
NR
304 SS
N/A
<400 ppm
<250 ppm
<150 ppm
316 SS
N/A
<1000 ppm
<550 ppm
<375 ppm
Titanium
N/A
>1000 ppm
>550 ppm
>375 ppm
Erosion and Clogging
Particulate Size and Erosion
<10 ppm of particles and a
maximum velocity of 6 fps. <10 ppm (<1 ppm “sandfree” for reinjection) of particles and a maximum
All
velocity of 6 fps. Filtered for maximum 800 micron size. Any particulate that
Filtered for maximum
is not removed can potentially clog components.
800 micron size.
Brackish
Use cupronickel heat exchanger when concentrations of calcium or
All
N/A
sodium chloride are greater than 125 ppm are present. (Seawater is
approximately 25,000 ppm.)
LEGEND
HWG — Hot Water Generator
HX — Heat Exchanger
N/A — Design Limits Not Applicable Considering Recirculating
Potable Water
NR — Application Not Recommended
SS
— Stainless Steel
*Heat exchanger materials considered are copper, cupronickel, 304 SS
(stainless steel), 316 SS, titanium.
†Closed recirculating system is identified by a closed pressurized piping
system.
**Recirculating open wells should observe the open recirculating design
considerations.
48
††If the concentration of these corrosives exceeds the maximum allowable
level, then the potential for serious corrosion problems exists.
Sulfides in the water quickly oxidize when exposed to air, requiring that no
agitation occur as the sample is taken. Unless tested immediately at the
site, the sample will require stabilization with a few drops of one Molar
zinc acetate solution, allowing accurate sulfide determination up to
24 hours after sampling. A low pH and high alkalinity cause system problems, even when both values are within ranges shown. The term pH refers
to the acidity, basicity, or neutrality of the water supply. Below 7.0, the
water is considered to be acidic. Above 7.0, water is considered to be
basic. Neutral water contains a pH of 7.0.
To convert ppm to grains per gallon, divide by 17. Hardness in mg/l is
equivalent to ppm.
Acoustical design
Sound power levels represent the sound as it is produced
by the source, the WSHP unit, with no regard to attenuation between the source and the space. Acoustical design
goals are necessary to provide criteria for occupied spaces
where people can be comfortable and communicate effectively over the background noise of the air-conditioning
system and other background noise sources.
Acoustical design goals are desirable sound pressure levels within a given conditioned space and are represented
by noise criteria (NC) curves. Noise criteria curve levels represent a peak over a full spectrum of frequencies. A high
value in a low frequency band has the same effect on NC
level as a lower value in a high frequency band. It is important that sound levels be balanced over the entire spectrum
relative to the NC curve. The lower the NC criteria curve,
the more stringent the room acoustical design must be to
meet the design goals.
It is important to know how to convert NC levels
from the unit ratings in terms of sound power (Lw). This
conversion depends on the specifics of the acoustical environment of the installation.
The resulting calculations are compared to the NC curve
selected for the area to assess the acoustical design.
Some of the factors that affect conversion of sound
power to sound pressure and consequent NC level include:
• Type of acoustical ceiling
• Use of metal or flex duct
• Absorption in the occupied space
• Location in the occupied space
• Open or closed layout plan
• Use of open or ducted returns
• Orientation of unit to occupant
• Use of lined or unlined duct
OCTAVE BAND SOUND PRESSURE LEVEL (Lp)
ASSOCIATED WITH NC CURVES
NOISE
CRITERIA
CURVES
NC-15
NC-20
NC-25
NC-30
NC-35
NC-40
NC-45
NC-50
NC-55
NC-60
NC-65
OCTAVE BAND SOUND PRESSURE LEVEL (Lp)
Frequency (Hz)
63 125 250 500 1000 2000 4000 8000
49
36
26
17
17
14
12
11
52
41
33
27
22
19
17
16
54
45
38
31
27
24
22
21
58
49
41
36
31
29
28
27
61
53
45
40
36
34
33
32
64
57
50
45
41
39
38
37
67
61
54
49
46
44
43
42
71
64
58
54
51
49
48
47
74
68
63
58
56
54
53
52
77
71
67
63
61
59
58
57
80
75
71
68
66
64
63
62
WSHP sound control
The analysis of the projected sound level in the conditioned
space caused by a WSHP unit located in a ceiling plenum is
quite involved. The key is to have good sound power ratings (Lw) in dB on the equipment to determine the sound
attenuation effect of the ductwork, ceiling and room. In
combination with utilizing standard Aquazone™ equipment
attenuating features or the advanced mute package features, suggestions for unit sound design are provided to design around the WSHP units.
Use the following guidelines for layout of Aquazone
WSHP units to minimize noise:
1. Obtain sound power ratings in accordance with latest
standards from manufacturers to select quietest
equipment.
2. Do not locate units over a space with a required NC
of 40 or less. Instead, locate units above less sensitive
noise areas such as above or in equipment rooms,
utility closets, restrooms, storage rooms, or above
corridors.
3. Provide at least 10 feet between WSHP units to avoid
the additive effect of two noise sources.
4. Provide an acoustical pad underneath the WSHP unit
in applications where the unit must be mounted
above noise sensitive areas such as private offices or
conference rooms. The pad attenuates radiated noise.
Be sure the pad has an area at least twice that of the
WSHP footprint.
5. Maximize the installed height above the suspended
ceiling.
6. Be sure the WSHP unit is located at least 6 feet away
from any ceiling return grille to prevent line-of-sight
casing noise to reach the space below.
7. Suspend the WSHP unit from the ceiling with hangers that utilize spring or neoprene type isolators to
reduce vibration transmission.
8. Utilize flexible electrical connections to the WSHP
unit. DO NOT USE NOT RIGID CONNECTIONS.
9. Utilize flexible loop water and condensate piping connections to the WSHP unit.
10. Use a canvas duct connector to connect the WSHP
discharge to the downstream duct system. This
reduces vibration-induced noise.
11. Provide acoustic interior lining for the first 20 feet of
discharge duct, or until the first elbow is reached. The
elbow prevents line-of-site sound transmission in the
discharge duct.
12. Provide turning vanes in ductwork elbows and tees to
reduce air turbulence.
13. Size the sheet metal supply duct with velocities no
greater than 1000 fpm.
14. Ensure ductwork is rigid.
15. Use round duct whenever possible to further reduce
noise.
16. Allow at least 3 equivalent duct diameters of straight
duct upstream and downstream of the unit before
allowing any fittings, transitions, etc.
17. Seal all penetrations around duct entering the space.
18. Provide a 4-ft run-out duct made of flexible material
to connect a diffuser to the supply trunk duct. The
flex duct provides an “attenuating end-effect” and
reduces duct-transmitted sound before it reaches the
49
Application data (cont)
space. Typically a 6 dB sound reduction can be
accomplished with the use of flex duct.
19. Locate the run-out duct balancing damper as far away
from the outlet diffuser as possible. Locating the
balancing damper at the trunk duct exit is the best
location.
20. If return air is drawn through a ceiling plenum, provide an acoustically lined return duct elbow or “L”
shaped boot at the WSHP to eliminate line-of-sight
noise into the ceiling cavity and possible through ceiling return air grilles. Face the elbow or boot away
from the nearest adjacent WSHP unit to prevent additive noise.
21. Do not hang suspended ceiling from the ductwork.
If installing unit in small equipment rooms or closets, the
following additional guidelines apply:
1. Mount the unit on a pad made of high-density sound
absorbing material such as rubber or cork. Extend the
pad beyond the WSHP unit footprint by at least
6 inches in each direction.
2. Since the unit returns airflow through a grille
mounted in a closet door, provide a sound barrier or
some other modification of the closet to prevent lineof-site noise into the space.
3. Follow good duct design practice in sizing and locating the connection of the WSHP discharge to the
supply duct system. Use an elbow with turning vanes
and bent in the direction of the fan rotation to minimize turbulence. Make any duct transitions as smooth
and as gradual as possible to again minimize turbulence and loss of fan static pressure.
OPERATING LIMITS
AIR LIMITS
Min. Ambient Air
Rated Ambient Air
Max. Ambient Air
Min. Ent. Air
Normal Entering Air db/wb
Max. Entering Air db/wb
WATER LIMITS
Min. Entering Water
Normal Entering Water
Max. Entering Water
COOLING (F)
45
80
100
50
75/63-80/67
110/83
HEATING (F)
45
70
85
40
70
80
*30
40-90
110
45 (*20)
40-90
90
LEGEND
db — Dry Bulb
wb — Wet Bulb
*With antifreeze, optional extended range insulation and low temperature cutout jumper clipped for antifreeze.
50
Solenoid valves
In applications using variable flow pumping, solenoid
valves can be field installed and operated from the control
board in the Aquazone™ WSHP unit.
Freeze protection
Applications where systems are exposed to outdoor
temperatures below freezing (32 F) must be protected from
freezing. The most common method of protecting water
systems from freezing is adding glycol concentrations into
the water. Design care should be used when selecting both
the type and concentrations of glycol utilized due to the
following:
• Equipment and performance may suffer with high concentrations of glycol and other antifreeze solutions
• Loss of piping pressure may increase greatly, resulting
in higher pumping costs
• Higher viscosity of the mixture may cause excess corrosion and wear on the entire system
• Acidity of the water may be greatly increased, promoting corrosion
• Glycol promotes galvanic corrosion in systems of dissimilar metals. The result is corrosion of one metal by
the other, causing leaks.
Controls
WSHP Open sequence of operation
The WSHP Open multi-protocol controller will control mechanical cooling, heating and waterside economizer outputs based on its own space temperature input and set
points. An optional CO2 IAQ (indoor air quality) sensor
mounted in the space can maximize the occupant comfort.
The WSHP Open controller has its own hardware clock
that is automatically set when the heat pump software is
downloaded to the board. Occupancy types are described
in the scheduling section below. The following sections describe the functionality of the WSHP Open multi-protocol
controller. All point objects referred to in this sequence of
operation will be referenced to the objects as viewed in the
BACview6 handheld user interface.
Scheduling — Scheduling is used to start/stop the unit
based on a time period to control the space temperature to
specified occupied heating and cooling set points. The
controller is defaulted to control by occupied set points all
the time, until either a time schedule is configured with
BACview6, Field Assistant, i-Vu® Open, or a third party
control system to enable/disable the BAS (Building Automation System) on/off point. The local time and date must
be set for these functions to operate properly. The occupancy source can be changed to one of the following:
Occupancy schedules — The controller will be occupied
24/7 until a time schedule has been configured using either Field Assistant, i-Vu Open, BACview6 or a third party
control system to enable/disable the BAS on/off point.
The BAS point can be disabled by going to Config, then
Unit, then Occupancy Schedules and changing the point
from enable to disable then clicking OK.
NOTE: This point must be enabled in order for the i-Vu
Open, Field Assistant, or BACview6 control system to assign a time schedule to the controller.
Schedule_schedule — The unit will operate according to
the schedule configured and stored in the unit. The schedule is accessible via the BACview6 Handheld tool, i-Vu
Open, or Field Assistant control system. The daily schedule
consists of a start/stop time (standard or 24-hour mode)
and seven days of the week, starting with Monday and
ending on Sunday. To enter a daily schedule, navigate to
Config, then Sched, then enter BACview6 Admin Password (1111), then go to schedule_schedule. From here,
enter either a Weekly or Exception schedule for the unit.
Occupancy input contact — The WSHP Open controller
has the capability to use an external dry contact closure to
determine the occupancy status of the unit. The Occupancy Schedules will need to be disabled in order to utilize the
occupancy contact input.
NOTE: Scheduling can only be controlled from one
source.
BAS (Building Automation System) on/off — A BAS
system that supports network scheduling can control the
unit through a network communication and the BAS
scheduling function once the Occupancy Schedules have
been disabled.
NOTE: Scheduling can either be controlled via the unit or
the BAS, but not both.
Indoor fan — The indoor fan will operate in any one of
three modes depending on the user configuration selected.
Fan mode can be selected as Auto, Continuous, or Always On. In Auto mode, the fan is in intermittent operation during both occupied and unoccupied periods. Continuous fan mode is intermittent during unoccupied periods
and continuous during occupied periods. Always On mode
operates the fan continuously during both occupied and
unoccupied periods. In the default mode, Continuous, the
fan will be turned on whenever any one of the following is
true:
• The unit is in occupied mode as determined by its occupancy status.
• There is a demand for cooling or heating in the unoccupied mode.
• There is a call for dehumidification (optional).
When power is reapplied after a power outage, there
will be a configured time delay of 5 to 600 seconds before
starting the fan. There are also configured fan delays for
Fan On and Fan Off. The Fan On delay defines the delay
time (0 to 30 seconds; default 10) before the fan begins to
operate after heating or cooling is started while the Fan Off
delay defines the delay time (0 to 180 seconds; default 45)
the fan will continue to operate after heating or cooling is
stopped. The fan will continue to run as long as the compressors, heating stages, or the dehumidification relays are
on. If the SPT failure alarm or condensate overflow alarm
is active; the fan will be shut down immediately regardless
of occupancy state or demand.
Fan speed control (during heating) — Whenever heat is required and active, the control continuously monitors the
supply-air temperature to verify it does not rise above the
configured maximum heating SAT limit (110 F default). As
the SAT approaches this value, the control will increase the
fan speed as required to ensure the SAT will remain within
the limit. This feature provides the most quiet and efficient
operation by operating the fan at the lowest speed
possible.
Fan speed control (during cooling) — Whenever mechanical cooling is required and active, the control continuously
monitors the supply-air temperature to verify it does not
fall below the configured minimum cooling SAT limit (50 F
default). As the SAT approaches this value, the control will
increase the fan speed as required to ensure the SAT will
remain within the limit. The fan will operate at lowest
speed to maximize latent capacity during cooling.
Cooling — The WSHP Open controller will operate one
or two stages of compression to maintain the desired cooling set point. The compressor outputs are controlled by
the PI (proportional-integral) cooling loop and cooling stages capacity algorithm. They will be used to calculate the desired number of stages needed to satisfy the space by comparing the space temperature (SPT) to the appropriate
cooling set point. The water side economizer, if applicable,
will be used for first stage cooling in addition to the compressor(s). The following conditions must be true in order
for the cooling algorithm to run:
• Cooling is set to Enable.
• Heating mode is not active and the compressor time
guard has expired.
51
Controls (cont)
• Condensate overflow input is normal.
• If occupied, the SPT is greater than the occupied cooling set point.
• Space temperature reading is valid.
• If unoccupied, the SPT is greater than the unoccupied
cooling set point.
• If economizer cooling is available and active and the
economizer alone is insufficient to provide enough
cooling.
• OAT (if available) is greater than the cooling lockout
temperature.
If all the above conditions are met, the compressors will
be energized as required, otherwise they will be deenergized. If cooling is active and should the SAT approach the
minimum SAT limit, the fan will be indexed to the next
higher speed. Should this be insufficient and if the SAT falls
further (equal to the minimum SAT limit), the fan will be indexed to the maximum speed. If the SAT continues to fall
5 ° F below the minimum SAT limit, all cooling stages will
be disabled.
During Cooling mode, the reversing valve output will be
held in the cooling position (either B or O type as configured) even after the compressor is stopped. The valve will
not switch position until the Heating mode is required.
The configuration screens contain the minimum SAT
parameter as well as cooling lockout based on outdoor-air
temperature (OAT) Both can be adjusted to meet various
specifications.
There is a 5-minute off time for the compressor as well
as a 5-minute time delay when staging up to allow the SAT
to achieve a stable temperature before energizing a second
stage of capacity. Likewise, a 45-second delay is used
when staging down.
After a compressor is staged off, it may be restarted
again after a normal time-guard period of 5 minutes and if
the supply-air temperature has increase above the minimum supply-air temperature limit.
The WSHP Open controller provides a status input to
monitor the compressor operation. The status is monitored to determine if the compressor status matches the
commanded state. This input is used to determine if a refrigerant safety switch or other safety device has tripped
and caused the compressor to stop operating normally. If
this should occur, an alarm will be generated to indicate the
faulted compressor condition.
Heating — The WSHP Open controller will operate one
or two stages of compression to maintain the desired heating set point. The compressor outputs are controlled by
the heating PI (proportional-integral) loop and heating
stages capacity algorithm. They will be used to calculate
the desired number of stages needed to satisfy the space by
comparing the space temperature (SPT) to the appropriate
heating set point. The following conditions must be true in
order for the heating algorithm to run:
• Heating is set to Enable.
• Cooling mode is not active and the compressor time
guard has expired.
• Condensate overflow input is normal.
52
• If occupied, the SPT is less than the occupied heating
set point.
• Space temperature reading is valid.
• If unoccupied, the SPT is less than the unoccupied heating set point.
• OAT (if available) is less than the heating lockout
temperature.
If all the above conditions are met, the heating outputs
will be energized as required, otherwise they will be deenergized. If the heating is active and should the SAT approach
the maximum SAT limit, the fan will be indexed to the next
higher speed. Should this be insufficient, and the SAT rises
further reaching the maximum heating SAT limit, the fan
will be indexed to the maximum speed. If the SAT still continues to rise 5 ° F above the maximum limit, all heating
stages will be disabled.
During Heating mode, the reversing valve output will be
held in the heating position (either B or O type as configured) even after the compressor is stopped. The valve will
not switch position until the Cooling mode is required.
The configuration screens contain the maximum SAT
parameter as well as heating lockout based on outdoor-air
temperature (OAT); both can be adjusted to meet various
specifications.
There is a 5-minute off time for the compressor as well
as a 5-minute time delay when staging up to allow the SAT
to achieve a stable temperature before energizing a second
stage of capacity. Likewise, a 45-second delay is used
when staging down.
After a compressor is staged off, it may be restarted
again after a normal time-guard period of 5 minutes and if
the supply-air temperature has fallen below the maximum
supply air temperature limit.
The WSHP Open controller provides a status input to
monitor the compressor operation. The status is monitored to determine if the compressor status matches the
commanded state. This input is used to determine if a refrigerant safety switch or other safety device has tripped
and caused the compressor to stop operating normally. If
this should occur, an alarm will be generated to indicate the
faulted compressor condition. Also, if auxiliary heat is
available (see below), the auxiliary heat will operate to replace the reverse cycle heating and maintain the space
temperature as required.
Auxiliary heat — The WSHP Open controller can control a two-position, modulating water, or steam valve
connected to a coil on the discharge side of the unit and
supplied by a boiler or a single-stage ducted electric heater
in order to maintain the desired heating set point. Should
the compressor capacity be insufficient or a compressor
failure occurs, the auxiliary heat will be used. Unless the
compressor fails, the auxiliary heat will only operate to
supplement the heat provided by the compressor if the
space temperature falls more than one degree below the
desired heating set point (The amount is configurable). The
heat will be controlled so the SAT will not exceed the maximum heating SAT limit.
Auxiliary modulating hot water/steam heating reheat —
The control can modulate a hot water or steam valve
connected to a coil on the discharge side of the unit and
supplied by a boiler in order to maintain the desired heating set point should the compressor capacity be insufficient
or a compressor failure occurs. Unless a compressor fault
condition exists, the valve will only operate to supplement
the heat provided by the compressor if the space temperature falls more than one degree below the desired heating
set point. The valve will be controlled so the SAT will not
exceed the maximum heating SAT limit.
Two-position hot water/steam heating reheat — The control can operate a two-position, NO or NC, hot water or
steam valve connected to a coil on the discharge side of the
unit and supplied by a boiler in order to maintain the desired heating set point should the compressor capacity be
insufficient or a compressor failure occurs. Unless a compressor fault condition exists, the valve will only open to
supplement the heat provided by the compressor if the
space temperature falls more than one degree below the
desired heating set point. The valve will be controlled so
the SAT will not exceed the maximum heating SAT limit.
The heat stage will also be subject to a 2-minute minimum
OFF time to prevent excessive valve cycling.
Single stage electric auxiliary heat — The control can operate a field-installed single stage of electric heat installed on
the discharge side of the unit in order to maintain the desired heating set point should the compressor capacity be
insufficient or a compressor failure occurs. Unless a compressor fault condition exists, the heat stage will only operate to supplement the heat provided by the compressor if
the space temperature falls more than one degree below
the desired heating set point. The heat stage will be controlled so the SAT will not exceed the maximum heating
SAT limit. The heat stage will also be subject to a 2-minute
minimum OFF time to prevent excessive cycling.
Indoor air quality (IAQ) and demand controlled ventilation (DCV) —If the optional indoor air
quality sensor is installed, the WSHP Open controller can
maintain indoor air quality via a modulating OA damper
providing demand controlled ventilation. The control operates the modulating OA damper during occupied periods.
The control monitors the CO2 level and compares it to the
configured set points, adjusting the ventilation rate as required. The control provides proportional ventilation to
meet the requirements of ASHRAE (American Society of
Heating, Refrigerating and Air Conditioning Engineers)
specifications by providing a base ventilation rate and then
increasing the rate as the CO2 level increases. The control
will begin to proportionally increase ventilation when the
CO2 level rises above the start ventilation set point and will
reach the full ventilation rate when the CO2 level is at or
above the maximum set point. A user-configurable minimum damper position ensures that proper base ventilation
is delivered when occupants are not present. The IAQ configurations can be accessed through the configuration
screen. The following conditions must be true in order for
this algorithm to run:
• Damper control is configured for DCV.
• The unit is in an occupied mode.
• The IAQ sensor reading is greater than the DCV start
control set point.
The control has four user adjustable set points: DCV
start control set point, DCV maximum control set point,
minimum damper position, and DCV maximum damper
position.
Two-position OA damper — The control can be configured to operate a ventilation damper in a two-position ventilation mode to provide the minimum ventilation requirements during occupied periods.
Waterside economizer — The WSHP Open controller has the capability of providing modulating or twoposition water economizer operation (for a field-installed
economizer coil mounted to the entering air side of the unit
and connected to the condenser water loop) in order to
provide free cooling (or preheating) when water conditions
are optimal. Water economizer settings can be accessed
through the equipment status screen. The following conditions must be true for economizer operation:
• SAT reading is available.
• EWT reading is available.
• If occupied, the SPT is greater than the occupied cooling set point or less than the occupied heating set point
and the condenser water is suitable.
• Space temperature reading is valid.
• If unoccupied, the SPT is greater than the unoccupied
cooling set point or less than the unoccupied heating set
point and the condenser water is suitable.
Modulating water economizer control — The control has
the capability to modulate a water valve to control condenser water flowing through a coil on the entering air side
of the unit.
Cooling — The purpose is to provide an economizer cooling function by using the water loop when the entering water loop temperature is suitable (at least 5 ° F below space
temperature). If the water loop conditions are suitable,
then the valve will modulate open as required to maintain a
supply air temperature that meets the load conditions.
Should the economizer coil capacity alone be insufficient
for a period greater than 5 minutes, or should a high humidity condition occur, then the compressor will also be
started to satisfy the load. Should the SAT approach the
minimum cooling SAT limit, the economizer valve will
modulate closed during compressor operation.
Heating — Additionally, the control will modulate the water valve should the entering water loop temperature be
suitable for heating (at least 5 ° F above space temperature)
and heat is required. The valve will be controlled in a similar manner except to satisfy the heating requirement.
Should the economizer coil capacity alone be insufficient
to satisfy the space load conditions for more than 5 minutes, then the compressor will be started to satisfy the load.
Should the SAT approach the maximum heating SAT limit,
the economizer valve will modulate closed during compressor operation.
Two-position water economizer control — The control has
the capability to control a NO or NC, two-position water
valve to control condenser water flow through a coil on the
entering air side of the unit.
Cooling — The purpose is to provide a cooling economizer function directly from the condenser water loop when
53
Controls (cont)
the entering water loop temperature is suitable (at least
5 ° F below space temperature). If the optional coil is provided and the water loop conditions are suitable, then the
valve will open to provide cooling to the space when required. Should the capacity be insufficient for a period
greater than 5 minutes, or should a high humidity condition occur, then the compressor will be started to satisfy
the load. Should the SAT reach the minimum cooling SAT
limit, the economizer valve will close during compressor
operation.
Heating — Additionally, the economizer control will open
the water valve should the entering water loop temperature
be suitable for heating (at least 5 ° F above space temperature) and heat is required. The valve will be controlled in a
similar manner except to satisfy the heating requirement.
Should the coil capacity be insufficient to satisfy the space
load for more than 5 minutes, then the compressor will be
started to satisfy the load. Should the SAT reach the maximum heating SAT limit, the economizer valve will close
during compressor operation.
Demand limit — The WSHP Open controller has the
ability to accept three levels of demand limit from the network. In response to a demand limit, the unit will decrease
its heating set point and increase its cooling set point to
widen the range in order to immediately lower the electrical demand. The amount of temperature adjustment in response is user adjustable for both heating and cooling and
for each demand level. The response to a particular demand level may also be set to zero.
54
Condenser water linkage — The control provides optimized water loop operation using an universal controller
(UC) open loop controller. Loop pump operation is automatically controlled by WSHP equipment occupancy
schedules, unoccupied demand and tenant override conditions. Positive pump status feedback prevents nuisance
fault trips. The condenser water linkage operates when a
request for condenser water pump operation is sent from
each WSHP to the loop controller. This request is generated whenever any WSHP is scheduled to be occupied, is
starting during optimal start (for warm-up or pull down prior to occupancy), there is an unoccupied heating or cooling demand, or a tenant pushbutton override. At each
WSHP, the water loop temperature and the loop pump
status is given. The WSHP will NOT start a compressor until the loop pumps are running or will shutdown the compressors should the pumps stop. This prevents the WSHP
from operating without water flow and thus tripping out on
refrigerant pressure, causing a lockout condition. The
WSHP Open controller control will prevent this from occurring. Also, the loop controller can be configured to start
the pumps only after a configurable number of WSHPs are
requesting operation (from 1-"N"). This can be used to prevent starting the entire loop operation for only one WSHP.
Meanwhile, the WSHPs will not operate if the loop pump
status is off and therefore the WSHP compressor will not
run.
Guide specifications
Commercial Vertical Water Source Heat
Pump Units with Puron® Refrigerant
(R-410A)
HVAC Guide Specifications
Size Range: 84,000 to 300,000 Btuh Cooling
Capacity
Carrier Model Number: 50VQP
Part 1 — General
1.01 SYSTEM DESCRIPTION
A. Heat pump units are designed to operate with 60 to
95 F water temperature or 20 to 110 F water temperature when the extended range option is
selected. Units shall consist of high-efficiency scroll
compressor(s) and shall have 2 independent refrigeration circuits where appropriate. The air discharge
and return are as specified on drawings.
B. Units shall be individually packaged with wooden
skid covered with protective corner posts and plastic
stretch wrapping for maximum protection.
1.02 QUALITY ASSURANCE
A. Basic unit shall be rated and certified in accordance
with ARI/ISO/ASHRAE Standards.
B. Units shall have insulation and adhesive which meet
NFPA 90A requirements for flame spread and
smoke generation, and assembled units shall be ETL
certified, US and Canada, and meet UL-181
standards.
C. Units shall be factory tested under normal operating
conditions at nominal water flow rates to assure
proper operation of all components and safety
devices.
Part 2 — Product
2.01 EQUIPMENT
A. Heat Pump Assembly:
Factory-tested and assembled single-piece water
source heat pump units shall be factory wired,
charged with Puron refrigerant (R-410A), contain
refrigerant-to-water heat exchanger, refrigerant-toair heat exchanger, 4-way reversing valve, fan motor
assembly, compressor, metering device, and all
internal controls and safety devices.
B. Unit Cabinet:
1. Unit shall be constructed of heavy gage galvanized sheet metal with powder coat paint finish
and with removable service panels, hanging
brackets, and insulated galvanized steel condensate pan of welded construction.
2. Supply and return water connections shall be
copper FTP, flush-mounted and rigidly connected to prevent damage to tubing and/or
noise generation.
3. Cabinet construction shall permit service testing
without air bypass on coil and shall incorporate
factory-installed supply ductwork connections.
Direct connection to fan housing is not recommended due to sound considerations.
C.
D.
E.
F.
G.
4. Unit shall have separate entrances for high and
low-voltage electrical supplies.
5. One-in. wide filter bracket and 1-in. fiberglass
disposable filter shall be provided on each unit.
6. All interior surfaces shall be lined with 1/2-in.
thick, 11/2 lb per cu ft density acoustic type
fiberglass insulation. All fiberglass shall be
coated and all edges shall be tucked under
flanges to prevent the introduction of glass
fibers in the airstream.
Fan and Motor Assembly:
1. Units shall have belt driven single or dual
centrifugal fans. The fan motor shall be
permanently lubricated with internal overload
protection.
2. Fan motor shall be isolated from the fan housing by flexible rubber isolation grommets.
Compressors:
Unit shall have heat pump duty, high-efficiency
scroll compressor(s) with internal and external
isolation.
Heat Exchangers:
1. Refrigerant-to-air coil shall be aluminum/
copper finned-tube construction type rated for
625 psig and shall be fully degreased at the factory to prevent possible condensate blowoff.
2. Refrigerant-to-water heat exchanger shall be
steel/copper tube-in-tube type rated for 625 psig
refrigerant, 500 psig water-side pressures.
3. Optional steel/cupronickel refrigerant-to-water
heat exchanger shall be used for open loop
applications, or where water quality cannot be
maintained as specified by manufacturer.
Refrigerant Components:
1. Refrigeration circuit components shall include
liquid line service valve, suction line service
valve, reversing valve, a full charge of compressor oil, and a holding charge of refrigerant.
2. Thermostatic expansion valve shall be provided
for refrigerant metering.
Controls and Safeties:
1. Safety devices on all units shall include lowpressure sensor or loss-of-charge switch, highpressure switch, low water temperature sensor,
and condensate overflow switch.
2. The standard Complete C electronic control
system shall interface with a heat pump (Y,O)
wall thermostat (mechanical or electronic). The
control system shall have the following features:
a. 75 VA transformer.
b. Anti-short cycle time delay on compressor
operation; time delay shall be 5 minutes
minimum.
c. Random start on power-up.
d. Low voltage protection.
55
Guide specifications (cont)
e.
f.
g.
h.
High voltage protection.
Condensate overflow shutdown.
Unit shutdown on low refrigerant pressures.
Unit shutdown on high or low water temperature (selectable for antifreeze solutions).
i. Option to reset unit at thermostat or disconnect. Fault type shall be retained in memory
if reset at thermostat.
j. Automatic intelligent reset. Unit shall automatically restart 5 minutes after shutdown if
the fault has cleared. Should a fault occur 3
times sequentially, then lockout will occur.
k. Ability to defeat time delays for servicing.
l. Light-emitting diode (LED) to indicate high
pressure, low pressure, improper voltage,
water coil freeze protection, air coil freeze
protection, condensate overflow, and control status.
m. Unit Performance Monitor to indicate inefficient operating conditions prior to unit
lockout.
n. Remote fault type indication at thermostat.
o. Single harness connection for all safety
devices.
p. Selectable 24-v or pilot duty dry contact
alarm output.
q. 24-v output to cycle a motorized water valve
with compressor contactor.
3. The optional Deluxe D electronic control shall
have all the features of the Complete C control,
with the following additional features:
a. A removable thermostat connector.
b. Random start on return from night setback.
c. Minimized reversing value operation for
extended life and quiet operation.
d. Night setback control from low temperature
thermostat, with 2-hour override initiated by
a momentary signal from the thermostat.
e. Dry contact night setback output for digital
night setback thermostats.
f. Ability to work with heat/cool (Y, W)
thermostats.
g. Ability to work with heat pump thermostats
using O or B reversing valve control.
h. Single grounded wire to initiate night setback or emergency shutdown.
i. Boilerless system control can switch automatically to electric heat at low loop water
temperature.
j. Control board shall allow up to 3 units to be
operated from one thermostat without any
auxiliary controls.
k. A relay to operate an external damper. The
control to be such that the damper will not
56
open until 30 minutes after the unit comes
back from Unoccupied mode.
l. A relay to restart a central pump or control a
24-v motorized water valve.
4. WSHP Open Multiple Protocol Control:
Units shall have all the features above (either C
or D boards) and the state of the art WSHP
Open multiple protocol interface board. All
point objects will have the ability to be viewed in
the BACview6 Handheld user interface. This
will permit all units to be daisy chain connected
by a 2-wire twisted pair shielded cable. The following points must be available at a central or
remote computer location:
a. space temperature
b. leaving water temperature
c. discharge air temperature
d. command of space temperature set point
e. cooling status
f. heating status
g. low temperature sensor alarm
h. high pressure switch alarm
i. fan on/off position of space thermostat
j. unoccupied/occupied command
k. cooling demand
l. heating demand
m. fan “ON/AUTO” command
n. fault prevention with auto reset
o. itemized fault code viewed with BACview
interface
Additional WSHP Open multiple protocol control features shall include:
a. two-position OA damper
b. modulating OA damper with DCV
c. auxiliary modulating hot water/steam
heating
d. two-position hot water/steam heating
e. single stage electric auxiliary heat
f. auto fan speed control (heating/cooling)
g. power fail restart delay
h. dehumidification
i. modulating water economizer control
j. two-position water economizer control
5. PremierLink™ Controller:
This control will function with Carrier Comfort
Network® (CCN) and ComfortVIEW™ software.
It shall also be compatible with ComfortLink™
controllers. It shall be ASHRAE 62-99 compliant and Internet ready. It shall accept a CO2
sensor in the conditioned space and be demand
control ventilation (DCV) ready. The communication rate must be 38.4K or faster. It shall
include an integrated economizer controller.
6. LonWorks Interface System:
Units shall have all features listed above (either
Complete C or Deluxe D) and the control board
shall be supplied with a LonWorks interface
board, which is LONMark certified. This will
permit all units to be daisy chained via a 2-wire
twisted pair shielded cable. The following points
must be available at a central or remote computer location:
a. space temperature
b. leaving-water temperature
c. discharge-air temperature
d. command of space temperature set point
e. cooling status
f. heating status
g. low temperature sensor alarm
h. low pressure sensor alarm
i. high pressure switch alarm
j. condensate sensor alarm
k. high/low voltage alarm
l. fan "ON/AUTO" position of space
thermostat
m. unoccupied / occupied command
n. cooling command
o. heating command
p. fan "ON / AUTO" command
q. fault reset command
r. itemized fault code revealing reason for
specific shutdown fault (any one of 7)
This option also provides the upgraded 75 va
control transformer with load side short circuit
and overload protection via a built-in circuit
breaker.
H. Electrical:
1. A control box shall be located within the unit
compressor compartment and shall contain a
75 va transformer, 24-volt activated, 3-pole compressor contactor, terminal block for thermostat
wiring and solid-state controller for complete unit
operation. Electro-mechanical operation WILL
NOT be accepted.
2. Units shall be nameplated for use with timedelay fuses or HACR circuit breakers.
3. Unit controls shall be 24-volt and provide heating or cooling as required by the remote
thermostat.
I. Sound Attenuation Package (Mute Package):
Consists of attenuation material that is applied to
the cabinet to reduce noise. Attenuation material
shall be applied to the basepan, compressor access
panels, and blower housing.
J. High-Static Blower:
The optional high-static blower provides increased
airflow at various static pressure conditions.
K. Special Features:
1. Aquazone™ Thermostat Controls:
a. Programmable multi-stage thermostat offers
7-day clock, holiday scheduling, large backlit
display and remote sensor capability.
b. Programmable 7-day light-activated thermostat offers occupied comfort settings with
lights on, and unoccupied energy savings
with lights off.
c. Programmable 7-day flush-mount thermostat offers locking coverplate with tamperproof screws, flush to wall mount, dual point
with adjustable deadband, O or B terminal,
and optional remote sensor.
d. Programmable 5-day thermostat offers
2-stage heat, 2-stage cool, auto changeover,
5-minute built-in compressor protection, and
included locking cover.
e. Non-programmable thermostat offers 2 heat
stages, 2 cool stages, auto changeover,
5-minute built-in compressor protection, and
included locking cover.
2. Aquazone™ system loop control panel shall
include a pre-programmed, easy to use, Carrier
Comfort Controller set up for a WSHP system.
The features of the loop control panel shall be
configured for the specific installation to include
the following:
a. The loop control panel shall coordinate,
monitor, or control all WSHP units and
ancillary equipment including cooling towers, boilers, and system pumps.
b. Panel shall be provided with 2, 4, 6, or
8 stages of system heat rejection.
c. Panel shall be provided with 2, 4, 6, or
8 stages of system heat addition.
d. Panel shall be provided with stand-alone
(i.e., non-communicating) operation with the
ability to control 10 or 18 zones of WSHP
units.
e. Panel shall be provided to control variable
frequency cooling tower fan operation.
f. System pumping operation shall be configured for start/stop, lead/lag, or variable
frequency pump operation.
g. Loop panel shall be direct digital control
compatible using the CCN and WSHP units
using PremierLink CCN controllers.
3. Filters:
Filters are available in 2 in. or 4 in. (MERV 8)
sizes.
4. Filter Rack:
Filter rack for one, 2, or 4 in. filters enhances
the filtration system of the water source heat
pump.
NOTE: Filter rack does not include filters.
57
Guide specifications (cont)
5. Fire-Rated Hose Kits:
Kits include a fixed MPT on one end and a
swivel with an adapter on the other end. Hose
kits can be either stainless steel or galvanized.
6. Ball Valves (Brass Body):
Valves are for shutoff and balancing water flow.
Available with memory, memory stop, and
pressure temperature ports.
7. Y Strainers (Bronze Body):
Strainers are “Y” type configuration with a
brass cap. Maximum operating pressure rating
of strainers is 450 psig. Strainer screen made
of stainless steel.
8. Solenoid Valves (Brass Body):
Valves provide slow operation for quiet system
application.
9. Hose Kit Assemblies:
Assemblies include a ported ball valve with pressure temperature (P/T) plug ports and flexible
stainless steel hose with swivel and nipple.
Return hose includes a ball valve, preset measure flow (gpm) with two P/T ports, and flexible
stainless steel hose with a swivel and nipple.
10. Multiple-protocol WSHP Open controller
remote sensors for Aquazone flush-mount
thermostats and DDC control options. Only
Carrier sensors can be used with the WSHP
Open controller. Sensors are available as
follows:
a. SPT Standard offers space temperature sensor with communication port.
58
b. SPT Plus offers space temperature sensor
with set point adjust, local override with indicating light and communication port.
c. SPT Pro offers space temperature sensor
with LCD display, set point adjust, local
override, alarm icon, outside air, and unit
status with heating and cooling set points.
d. SPT Pro+ offers space temperature sensor
with LCD display, set point adjust, local
override, alarm icon, outside air, unit status
with heating and cooling set points, and fan
speed control.
11. PremierLink™ Accessories:
Accessories include supply air temperature sensors, communicating room sensors, CO2 sensors, and linkage thermostats to provide a fully
integrated DDC (direct digital control) system.
12. Extended Range:
Extended range units provide an insulated water
circuit for the coaxial coil and refrigerant circuit
to prevent condensation, and therefore potential dripping problems, in applications where
the entering water temperature is beyond the
normal operating range.
13. LON wall sensors are available in 3 models:
sensor only, sensor with status override indicator, and sensor with set point, status adjustment
override, and digital LCD display.
59
Carrier Corporation • Syracuse, New York 13221
709
7-09
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Section 6
Pg 60
Catalog No. 04-52500049-01
Printed in U.S.A.
Form 50VQP-1PD
Replaces: New
Tab
6a
Download PDF