Autostart | AS-6250V | User guide | Autostart AS-6250V User guide

O N E - W A Y A U T O M A T I C / M A N U A L
T R A N S M I S S I O N R E M O T E S T A R T E R
W I T H F U L L A L A R M S Y S T E M
AS-6250v
User Guide
WARNING
It is the responsibility of the vehicle operator to ensure their vehicle
is parked in a safe and responsible manner.
1.
a) Manual transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in the NEUTRAL
position and the parking brake is engaged in order to avoid accidents
upon remote starting.
b) Automatic transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in “Park” in order to
avoid accidents upon remote starting.
(Note: Make sure that the automatic vehicle cannot start in "Drive".)
2. It is the user's responsibility to ensure that the remote starter is disabled
or put into valet mode before servicing.
FCC USER NOTICE (U.S.A.):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user's authority to operate the equipment.
DOC. 1.00
- AS-6250v -
- August 28, 2007 -
- MO -
Assembled in Canada
Table of Contents
Transmitter Part Number and Module Serial
User-selectable Options................................... 9
Number............................................................... 3
Safe Start..................................................... 9
Introduction ....................................................... 3
Remote Door Locks................................... 10
Basic Remote Operation .................................. 4
Passive or Active Arming........................... 10
Remote-starting Your Vehicle ......................... 4
Disarmed Notification ................................ 10
Setting Your Vehicle into Ready Mode ....... 4
Shock Sense And Warn-Away Sense....... 10
Remote-starting ........................................... 4
Siren Chirps ............................................... 10
Vehicle Presets.................................................. 4
Open Zone Notification.............................. 11
Heater & Heated Seat ................................. 4
Ignition-Controlled Door Locks .................. 11
Windshield Wipers & Radio & Headlights ... 4
Ignition Re-Lock......................................... 11
Driving Off.................................................... 4
Secure Lock............................................... 11
Idle Mode ..................................................... 4
Remote Trunk Release.............................. 11
Valet Modes................................................. 6
Starter Kill .................................................. 11
Ignition Valet ............................................ 7
Turbo Mode ............................................... 11
Remote Valet ........................................... 7
Engine Run Time....................................... 12
“Home Valet”
Mode.............................. 7
Extended Run Time................................... 12
Panic Mode.................................................. 8
Multi-Car Operation ................................... 13
Quick LockoutTM........................................... 8
Car Finder.................................................. 13
TM
Cold Weather Mode..................................... 8
Parking Lights Flash Rate
Priority Door Access .................................... 9
(Normal Operation) ......................................... 14
Chirp Delete................................................. 9
LIMITED LIFETIME WARRANTY .................... 15
Shock Delete ............................................... 9
P. 2
User Guide
Transmitter Part Number and Module Serial Number
Transmitter Part Number:
The installer is to write in the boxes below the Module’s serial number and the location of
the Valet Switch.
Module Serial Number:
Valet Switch is located (if installed):
Introduction
This Module is a state-of-the-art combination of an Alarm system and a remote car
starter. It represents a major breakthrough in vehicle security technology and remote
starter systems. This unit is distributed with a super-heterodyne antenna with range of up
to 1500 feet / 450 m.
User Guide
P. 3
Basic Remote Operation
This system is equipped with a 5-button multi-channel transmitter. It can operate two independent identically-equipped vehicles (see Multi-Car Operation for second-car
transmitter functions).
The functions of the transmitter are as follows:
LOCK: Locks the doors and arms
the STARTER KILL. Triggers Panic
if pressed more than 3 seconds
TRUNK: Opens the TRUNK or
activates the AUX 3 output
STOP: Stops the engine if pressed
for less than 3 seconds or triggers
Panic mode if pressed for more than
3 seconds.
UNLOCK: Unlocks the doors
and disarms the STARTER
KILL. Activates the AUX 2
output if priority door access
is configured.
Triggers Panic if pressed
more than 3 seconds
START: Remote starts the
engine or gets the system
into Cold Weather mode if
pressed for 3 seconds.
Note: Pressing the LOCK and UNLOCK buttons at the same time will activate the AUX 2 output.
Remote-starting Your Vehicle
If your vehicle has an automatic transmission, simply press the START button to remote
start your vehicle. Skip the next steps on to “Remote-starting”.
Warning: If you vehicle has an automatic transmission and the parking lights flash 15
times after pressing the START button, the parking brake is connected to ground. It is
imperative that you see your installer and have him disconnect the wire.
Setting Your Vehicle into Ready Mode
If your vehicle has a manual transmission you must read the following indications. In
order to start the vehicle by remote, the unit must first be set to Ready Mode. If the unit is
not set to Ready Mode, it cannot remote start the vehicle.
Please note that Ready Mode can be enabled by the remote or the handbrake,
depending on the option that was selected by your installer. Therefore, you must follow
the appropriate procedure between the two described below in order to set your vehicle
into Ready Mode.
Once the system is set to Ready Mode, the vehicle can be remote started and stopped at
any time. The system will exit Ready Mode if a door, the hood or the trunk is opened, if
the brake pedal is pressed, if the parking brake is disengaged or if the ignition key is
turned to the IGNITION ON (RUN) position.
To set the system to Ready Mode:
If Ready Mode is enabled by remote
If Ready Mode is enabled by handbrake
1.
Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the
neutral position.
2.
With the engine already running, apply the
parking brake once and release the brake
pedal.
Make sure to release the brake pedal.
P. 4
2. With the engine already running, apply the
parking brake twice and release the brake
pedal.
Make sure to release the brake pedal.
The parking lights will flash 3 times
User Guide
quickly and remain lit.
Skip to step 4.
3.
Within 20 sec. of engaging the parking brake,
press and hold LOCK, UNLOCK or
START/STOP on the transmitter.
The parking lights will flash 3 times
quickly and remain lit.
-
4. Remove the key: the engine will continue running.
5. Exit the vehicle and close all doors, hood and trunk.
6. Press for approx. 1 second either:
LOCK to lock the doors and shut down the engine;
UNLOCK to unlock the doors and shut down the engine;
START/STOP to shut down the engine without affecting the doors.
Remote-starting
Press the START button for approx. 1 second. The parking lights will come ON, informing
you that the unit has received your signal. The engine will start approx. 5 seconds later.
The parking lights will remain ON during the pre-programmed run time.
If the vehicle doesn’t start at the first attempt, the system will shut down. If your vehicle is
equipped with an automatic transmission, there will be 3 start attempts before the system
gives up.
Vehicle Presets
Heater & Heated Seat
When leaving the vehicle it is recommended to preset the accessory controls in
preparation for the next remote start. Settings for the blower motor (fan), front and rear,
as well as heated seats (if equipped) should not be left on HIGH. It is recommended to
leave the settings on LOW or MEDIUM instead.
Windshield Wipers & Radio & Headlights
Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to
become energized while running under remote start. When leaving the vehicle you must
ensure that the windshield wiper and headlight switches are OFF. Leaving the headlight
switch ON on certain vehicles could cause them to remain ON even after remote starter
shut down, resulting in a dead battery.
Driving Off
With the vehicle running under remote control, press the UNLOCK button to DISARM and
UNLOCK the doors. Enter the vehicle and do the following:
Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the Start
position while the engine is running. This will cause the starter motor to re-engage.)
Press the brakes to disengage the remote starter unit.
You are now ready to drive off.
Idle Mode
Convenience feature: Idle Mode allows you to keep the engine running and the doors
locked while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no
Key in the Ignition Switch) while the engine is running. For example, if you stop for a
User Guide
P. 5
delivery or at a convenience store, lock your vehicle and leave it running for the length of
a run cycle while you are away.
To leave the vehicle in Idle Mode if your vehicle has an automatic transmission:
1. With the engine running, press the LOCK or UNLOCK button (to unlock the doors)
or the START button on the remote control until the parking lights come on.
2. Remove the key and exit the vehicle. The engine will go on running.
3. Lock the doors if needed.
The engine will go on running until the user re-enters the vehicle or until the expiration of
the Engine Run Time.
If your vehicle has a manual transmission, Idle Mode can be activated through the
same routine as that used for Ready Mode; at the last step, the TRUNK button is pressed
instead of the other buttons:
1. Ensure that all the Doors are closed and that the Shifter is in the Neutral
position.
2. With the Engine already running, apply the Parking Brake and release the
Brake Pedal.
Make sure to release the brake pedal.
3. Within 20 sec. Push LOCK, UNLOCK or START on the Transmitter.
The parking lights will flash 3 times quickly and remain lit.
4. Remove the key: the Engine will go on running.
5. Exit the vehicle and close the Door.
6. Press the TRUNK button until the system is armed (the doors will be locked if
remote door lock is installed).
If the pre-programmed run-time expires or if the user shuts down the engine by remote
control, the vehicle will get in Ready Mode.
Caution: Do not leave children or pets unattended in a car running in Idle Mode.
Valet Modes
The system can be placed in Valet Mode to disable the remote starting capabilities. If the
vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the
engine from being remote-started accidentally.
To put the system into Valet Mode:
1. Turn the key to the IGNITION ON (RUN) position.
2. Within 3 sec. press the Valet button and release it, the Parking lights will flash
3 times. Turn the IGNITION OFF, the LED will come ON. (The system is in Valet
Mode.)
To take the system out of Valet Mode:
1. Turn the key to the IGNITION ON (RUN) position.
2. Within 3 sec. press and release the Valet button, the Parking Lights will flash
tiwce. The LED will go OUT. (The system is out of Valet Mode.)
The Valet button can only be used if the ignition key is in the IGNITION ON (RUN) position.
P. 6
User Guide
Ignition Valet
The system can be placed in Valet Mode to disable the remote starting capabilities. If the
vehicle needs to be serviced, or if you park it indoors, Valet Mode will prevent the engine
from being accidentally started by remote control.
To ENTER Valet Mode
1. With the key in the Ignition switch, turn the key to the ON (RUN/IGNITION) and then OFF
positions 5 times within 10 seconds.
2. The Parking Light will flash 3 times indicating the Module is now in Valet Mode. The
LED will turn ON solid.
To EXIT Valet Mode
1. With the key in the Ignition switch, turn the key to the ON (RUN/IGNITION) and then OFF
positions 5 times within 10 seconds.
2. The Parking Light will flash twice indicating the Module is now out of Valet Mode.
The LED will turn OFF.
Remote Valet
This feature will put your vehicle into Valet Mode using the remote transmitter instead of
the Valet button as above.
Note: Once the Electronic Valet is activated, the remote starter and Alarm features are
disabled.
To put the system into Valet Mode:
1. Hold down the UNLOCK and START buttons simultaneously for 3 seconds.
2. The Parking Lights will flash 3 times.
3. The siren will chirp twice and the LED will come ON.
To take the system out of Valet Mode:
1. Hold down the UNLOCK and START buttons simultaneously for 3 seconds.
2. The Parking Lights will flash 2 times.
3. The siren will chirp twice, then pause, then chirp twice again, and the LED will go OUT.
“Home Valet” TM Mode
This safety feature will remotely place the vehicle into a no-remote-start mode: if the
vehicle is parked indoors there is no danger of the vehicle starting by accident with the
remote control.
Note: Once the Home Valet Mode is activated, the vehicle will not start by remote.
To activate the Home Valet Mode:
1. Press the LOCK or UNLOCK button.
2. Within 3 seconds, press the STOP button until the parking lights go out.
To disable the Home Valet Mode:
1. Turn the ignition key to the IGNITION ON (RUN) position.
The system will warn you if someone attempts to start your vehicle while it stands in
Home Valet Mode. The parking lights will:
2. Go ON then OFF; then:
3. Flash twice, pause; then
User Guide
P. 7
4. Flash twice again.
Panic Mode
Safety feature: Activate Panic Mode in an emergency situation.
In an emergency situation, you can activate Panic Mode using the LOCK or UNLOCK or STOP
button. This will:
Shut down the engine,
Disarm the Starter Kill and
Unlock the doors (if UNLOCK is
Activate the siren for 1 minute.
pressed)
(See below for a description of the Starter
Or lock the door (if LOCK is pressed),
Kill.)
To activate Panic Mode
Press and hold the STOP button for approximately 3 seconds until the siren starts to sound
and the parking lights flash
Or press and hold the UNLOCK button for approximately 3 seconds until the siren starts to
sound and the parking lights flash: this will unlock the doors before the siren sounds.
Or press and hold the LOCK button for approximately 3 seconds until the siren starts to
sound and the parking lights flash: this will lock the doors before the siren sounds.
Panic Mode will automatically shut down after 1 minute.
Note: To stop Panic Mode before the 1-minute delay, press the LOCK or UNLOCK button until
the siren stops.
Quick LockoutTM
(Also called Secure Panic.) For fast protection, the system will LOCK all doors when you
press the brake pedal while the siren is sounding. (Quick Lockout is only available
when Panic has been activated.)
Cold Weather Mode
If your vehicle has a Manual transmission, Ready mode should be set before entering
Cold Weather. When the Cold Weather Mode is active, the engine starts every 2 hours
and runs for 3 minutes (or for 8 or 20 minutes with Diesel engines); the routine will go on
for a period of 24 hours.
To enter Cold Weather Mode:
Press and hold the START button for 3 seconds until the parking lights flash 3 times.
(If Safe Start is enabled, the START button must be pressed beforehand – see below.)
To enter Cold Weather Mode if Safe Start has been activated:
Press and hold the START button for 3 seconds until the parking lights flash 3 times.
To exit Cold Weather Mode, do any one of the following:
Open the hood.
Start the engine using the remote control.
Turn the ignition key to the IGNITION ON (RUN) position.
Press and hold the START button for 3 seconds. (The parking lights will flash once.)
To check whether Cold Weather Mode is active, press and release the brake pedal: the
parking lights should stay on while your foot is on the brake pedal.
P. 8
User Guide
Priority Door Access
This safety feature lets you unlock only the driver’s door when you press the
button on the transmitter, and then UNLOCK the rest of the vehicle doors if the
button is pressed for a second time within 3 seconds.
UNLOCK
UNLOCK
Chirp Delete
To temporarily disable the siren’s chirp confirmations upon arming and disarming (e.g. in
a quiet neighbourhood):
1. Press the TRUNK button, the Parking Light will flash once
2. Within 3 seconds, press the LOCK or UNLOCK button to arm or disarm without any
chirps.
Note: Your installer can program the Chirps Disabled feature if you want the chirps to be
permanently disabled.
Shock Delete
The shock sensor can be temporarily disabled. To temporarily disable shock and warnaway sense:
Press the TRUNK button and, within 3 seconds,
Press the STOP button.
Shock senses will now be ignored until the next disarming of the system.
User-selectable Options
The system was designed with flexibility and OEM integration in mind. With its
programmable options, this unit can single-handedly control nearly any electrical system
in your vehicle.
Note: The programming of your system should be left to a professional. Changing any one of
the settings may affect the operation of your system.
The user-selectable options are as follows:
Safe Start
Remote Door Locks
Passive or Active Arming
Disarm Notification
Shock Sense and Warn-Away Sense
Siren Chirps
Ignition-Controlled Door Locks
Ignition Re-Lock
Secure Lock
Remote Trunk Release
Starter Kill
Engine Run Time
Multi-Car Operation
Safe Start
Safety feature: Safe Start features will prevent accidental remote starts.
If this feature is enabled, the user must press the START button 2 times within 3 seconds
to remote-start the vehicle.
If Swap Start Mode has been configured by your installer, to remote-start your vehicle
press LOCK and UNLOCK simultaneously. (Press START to trigger the AUX 2 output.)
Safe Start features will eliminate accidental remote starts, e.g. when there are children
playing with the transmitter.
User Guide
P. 9
Remote Door Locks
If your system was installed with the Remote Door Locks option, you will have the
convenience of remote keyless entry.
To UNLOCK your doors and DISARM the system:
1. Press and hold the UNLOCK button for approx. 1 sec.
2. The parking lights will flash twice and the LED will go out to confirm that the
doors have been unlocked, that the Starter Kill feature is disarmed (if it was
installed) and that the Alarm is disabled.
To LOCK your doors and ARM the system:
1. Press and hold the LOCK button for approx. 1 sec.
2. The parking lights will flash once and the LED will flash slowly to confirm that
the doors have been locked, that the Starter Kill feature is enabled (if it was
installed) and that the Alarm is armed.
Passive or Active Arming
By default, the system is configured to Passive Arming Mode. In Passive Arming Mode,
the Starter Kill and the Alarm will automatically arm 30 seconds after the last door is
closed. The system will not arm itself if a door is left open.
Important note: When the system re-arms automatically or if there is an Alarm condition, you
can disarm the system by simply pressing the UNLOCK button.
Disarmed Notification
(OFF by default.) This feature will notify the user when the vehicle was left disarmed: after
the Engine has been shut down and all doors have been closed, after 10 seconds the
horn will honk once if the doors have been left unlocked.
Shock Sense And Warn-Away Sense
(Both enabled by default.) This system can react to a full shock by triggering the Alarm; it
can also respond to a lighter shock (30 % of the strength of a full shock) by giving a
warn-away (without triggering an Alarm condition). When the Engine is running after a
remote start, however, the system will prevent any Alarm condition to be triggered ;
it will still give a warning sound if warn-away is enabled.
Siren Chirps
(On by default.) The siren will chirp to confirm the system‘s basic operations:
By default, when the doors are being locked the siren will give one chirp if none of the
zones are active.
If a zone is active as the doors are being locked, the siren will give three chirps.
When the doors are being unlocked, the siren will give two chirps if no intrusion was
detected.
If an intrusion was detected, as the doors are being unlocked the siren will give four
chirps.
The system can alternatively be set to:
Warning Mode (no chirp during lock/unlock – unless a zone is active when locking, in
which case there will be 3 chirp upon locking – or unless the alarm was triggered, in
which case there will be 4 chirps when unlocking);
P. 10
User Guide
Open Zone Notification (the system will warn for doors opened up to 10 seconds after
arming).
No Chirp (the vehicle will not chirp under any circumstance).
Open Zone Notification
(Off by default.) This feature will warn the user when a Door is left open: upon the
arming of the Module, a 10-sec. notification delay will take place, after which the Siren
will chirp 3 times if an open door is detected.
Ignition-Controlled Door Locks
This is an added security feature. If your system was installed with the Ignition-Controlled
Door Locks option, the doors will automatically be locked as soon as the key is turned to
the IGNITION ON (RUN) position while the brakes are pressed. When the key us turned to the
OFF position, the doors will automatically be unlocked.
Ignition Re-Lock
When the Ignition-Controlled Door Locks option is enabled and the ignition is ON, should
any door be unlocked and opened, all the doors will be re-locked next time the brake
pedal is pressed.
Secure Lock
This is an added security feature. If your system was installed with the Secure Lock
option, it will automatically lock your doors and arm the system 4 seconds after your start
your car by remote. The system will automatically lock the doors again after shut-down.
Remote Trunk Release
If your system was installed with the Remote Trunk Release, you can open your trunk by
pressing the TRUNK button for 3 sec. on the transmitter, or by pressing the TRUNK button
twice within 3 sec.
Starter Kill
This added security feature will immobilize your vehicle when the system is armed. If
your system was installed with the Starter Kill option, you will not be able to start your
vehicle with the key unless the system has been disarmed first.
The Starter Kill option follows the Alarm arming function, and can therefore be
programmed to be active (will not arm automatically) or passive (will arm automatically).
In passive Mode, the Starter Kill can be set to arm automatically in 30 seconds either
with or without Siren chirps.
To disarm the Starter Kill, press and hold the UNLOCK button on the transmitter. The
parking lights will flash twice. (If door locks were installed, this will also unlock the doors.)
In passive Mode, the system will automatically re-arm itself 30 seconds after unlocking
the doors if the key has not been inserted in the ignition by then.
To arm the Starter Kill, press and hold the LOCK button on the transmitter. The parking
lights will flash once. (If the door locks were installed, this will also lock the doors.)
Turbo Mode
If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after
the user leaves the vehicle: the unit will take over the vehicle and keep it running for 60
seconds (or until it is shut down by remote control), then shut down the engine and set
the Remote Car Starter to Ready Mode.
User Guide
P. 11
If your vehicle has an automatic transmission, proceed as follows to set the system in
Turbo Mode:
1. With the engine already running, press the LOCK button on the transmitter until
the parking lights come ON.
2. Remove the ignition key from the ignition switch. The engine will go on
running.
3. Exit the vehicle and close the door.
4. Press the TRUNK button to lock the doors; the engine will shut down after
60 seconds of Turbo Mode.
If your vehicle has a manual transmission, follow all steps of the Ready Mode routine,
to activate Turbo Mode:
1. Ensure that all the doors are closed and that the shifter is in the neutral
position.
2. With the engine already running, apply the parking brake and release the brake
Pedal.
Make sure to release the brake pedal.
3. Within 20 sec. Press LOCK, UNLOCK or START on the transmitter.
The parking lights will flash 3 times quickly and remain lit.
4. Remove the key: the engine will go on running.
5. Exit the vehicle and close the door.
6. Press and hold either:
a. LOCK to lock the doors and shut down the engine after 60 sec.;
b. UNLOCK to unlock the doors and shut down the engine after 60 sec.;
c. STOP to shut down the engine immediately, without affecting the doors (this will
bypass Turbo Mode).
d.
TRUNK TO SET THE VEHICLE INTO IDLE MODE
Engine Run Time
If you have a gas engine, your system can be programmed to run the engine for 3, 15, or
25 minutes (15 min default). If you have a diesel engine, it can be programmed to run the
engine for 8, 20, or 30 minutes (20 min default).
Extended Run Time
With the vehicle running under a remote start, pressing and holding the START button for
more than 1 second will reset the run time counter to zero and restart the run time cycle
from the beginning.
To stop the vehicle, at any moment, simply press the STOP button. This procedure can
only be carried out once per remote start.
Example: if your Module is programmed for a run time of 3 minutes and your vehicle has
been running for 2 minutes already, pressing the START button will reset the counter to
zero and the Engine will run for another cycle (in this case, 3 minutes).
P. 12
User Guide
Multi-Car Operation
This option allows the owner of two vehicles, both equipped with identical systems, to
control both systems with only one remote transmitter. To control the second vehicle,
simultaneously press the TRUNK button and the button of the function you wish to use:
Press TRUNK + LOCK button simultaneously:
LOCK
Press TRUNK + UNLOCK:
UNLOCK
Press TRUNK + START:
START
Press TRUNK + STOP: STOP
Press TRUNK + LOCK + UNLOCK: AUX 3 (TRUNK)
Press TRUNK + START for 3 sec:COLD WEATHER MODE
Car Finder
When enabled, the Car Finder option will help you locate your vehicle by sending a
pulsating signal through the horn or the siren. To hear the signal, press the LOCK and
UNLOCK buttons simultaneously. This will produce a pulsating signal for the time you keep
the buttons pressed.
User Guide
P. 13
Parking Lights Flash Rate (Normal Operation)
Flashes
1
2
2 slow flashes then
8 quick flashes
3
4
5 Fast
6
8
10
When pressing START
15 quick flashes
1 – pause – 2
ON SOLID for 3
seconds….
ON continuously
ON 2 seconds
ON 4 seconds
ON 20 seconds
Constant flashes
up to 60 sec.
P. 14
•
•
•
•
•
•
•
Description
Doors locked, Alarm and starter kill armed.
•
Run time has expired.
•
TRUNK button pressed.
Remote start attempt cancelled by remote.
•
Doors unlocked, starter kill disarmed.
•
Exiting ignition valet
•
Power ON to OFF(Automatic
transmission)
Start signal received by the module.
Cold weather mode cancelled.
Exiting remote valet
Power-up reset.
Board set from manual to automatic;
power ON
• Reset from Manual to Automatic
• Entering ignition valet
• Entering remote valet.
• Entering or exiting Ready Mode
• Entering extended run time
• +12 V detected on the brake input wire
• Board set from automatic to manual; power
either while cranking or during run time.
ON
• Entering multi-speed tach programming. • Power ON to OFF ( manual transmission)
• Tach signal programmed.
• New transmitter programmed.
• A remote start was attempted while a tach-before-crank signal was detected before cranking.
• Unit reset
• A ground (-) signal was detected on the hood pin input wire.
• The parking brake is connected to ground (automatic transmission)
• There was a remote start attempt while the vehicle was in valet mode.
• Failed start: vehicle’s low battery voltage.
…followed by 1 flash
• Exiting cold weather mode
…followed by 3 flashes
• Entering cold weather mode
• Idle mode: Idle mode is engaged
• Run time: The vehicle has been remote started and is in run time.
• The hood has been opened and a ground (-) signal has been detected on the hood pin input
wire.
• Locking or unlocking a door (with Door pulses configured to 4 sec.)
• The hood pin has been flashed and you now have access to the programming options.
• In Siren or Horn Mode: Alarm condition generated by an intrusion, or when the System is
powered up.
User Guide
LIMITED LIFETIME WARRANTY
REMOTE STARTERS:
As the manufacturer, 4366859 Canada Inc. (“Autostart”) warrants to the original consumer purchaser only
(nontransferable) that the remote starter module (control box) shall be free from defects in materials and
workmanship for as long as the original consumer purchaser continuously owns the vehicle in which the
remote starter was originally installed, as specified below:
1)
For the first two years after the date of manufacture, as specified by the serial number on the module,
Autostart will replace the remote starter module free of charge with a new remote starter module.
2)
For the third year and any consecutive year after the date of manufacture, as specified by the serial
number on the module, Autostart will provide to the original consumer purchaser a new remote starter
module, for a repair charge of $25.00 USD.
In all cases, the consumer must return the remote starter module to the point of purchase, and must provide a copy
of the proof of purchase to said retailer. A remote starter module will be returned to the retailer for the consumer to
claim within a 4 (four)-week period. For case (2), a certified cheque or money order in the amount of $25.00 USD
must accompany the remote starter module, or the retailer may refuse the return.
ACCESSORIES:
Autostart warrants to the original consumer purchaser only (nontransferable) that it will replace any Autostart
accessory part for a one-year period from date of purchase. Accessories will only be replaced if proven defective in
material or workmanship, and if, when the accessory is returned to the point of purchase, the retailer is provided
with a copy of the proof of purchase. The accessory will be sent to the retailer for the consumer to claim within a 4
(four)-week period.
THE WARRANTY IS VOID IF:
1) The product has been damaged, altered in any way or tampered with, without the explicit written
consent of an Autostart technician. For remote starter modules, this includes the opening or
removal of the plastic covering of the module, or the removal or alteration of the barcode label on
the plastic covering of the module.
2) The product is damaged due to accident, fire, flood, shipping and handling, misuse, neglect, or
other conditions beyond the control of Autostart.
3) The product has been installed or repaired by anyone other than a certified technician.
4) The product has been improperly installed or used.
THE WARRANTY DOES NOT COVER:
1) Batteries.
2) Scratched or worn transmitter cases.
3) Installation and/or removal charges for all remote starter modules and accessories.
4) Shipping and handling charges incurred for product exchange or replacement.
5) Any material damages other than to the product itself.
6) Harnessing, L.E.D. lights, switches, inverters, relays, etc.
THIS LIMITED LIFETIME WARRANTY SHALL CONSTITUTE THE SOLE LIABILITY OF AUTOSTART
FOR OUR PRODUCTS, AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.
THERE ARE NO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO ASSUME FOR AUTOSTART
ANY OTHER LIABILITY WITH RESPECT TO THE SALE OR USE OF OUR PRODUCTS. AUTOSTART’S
LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR ANY
OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT FOR
DAMAGE IS THE BASIS OF THE CLAIM. UNDER NO CIRCUMSTANCE WILL AUTOSTART, ITS
DISTRIBUTORS OR THEIR AGENTS BEAR ANY LIABILITY WHATSOEVER FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
The parties hereto elect that any dispute regarding the present document be submitted to the appropriate Court located in the Province
of Quebec, District of Montreal. The parties hereto agree that this document is governed by and interpreted in accordance with the law
of Quebec. If the purchaser is located in a province of Canada other than Quebec, all matters dealing with the warranty of quality will
be governed by and interpreted in accordance with the law of Ontario. If the purchaser is located outside Canada, all matters dealing
with the warranty of quality will be governed by and interpreted in accordance with the United Nations Convention on Contracts for
the International Sale of Goods (the “Vienna Convention”).
User Guide
P. 15
Download PDF