Extron electronics | FOX 2G Tx | User`s manual | Extron electronics FOX 2G Tx User`s manual

User’s Manual
FOX 4G DA8
High Resolution Fiber Optic Distribution Amplifier
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-1461-01 Rev. A
02 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de  tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road, Songjiang
District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
Chapter One • Introduction..................................................... 1-1
About this Manual..................................................................... 1-2
About the FOX 4G DA8. ........................................................... 1-2
Features......................................................................................... 1-4
Chapter Two • Installation and Operation. .................. 2-1
Mounting the Unit..................................................................... 2-2
Tabletop placement................................................................ 2-2
Rack mounting........................................................................ 2-2
UL guidelines...........................................................................2-2
Mounting instructions............................................................2-3
Furniture mounting................................................................ 2-4
Through-desk mounting......................................................... 2-5
Rear Panel Features................................................................... 2-6
Front Panel Features.................................................................. 2-9
System Operation. ................................................................... 2-10
Chapter Three • Remote Control......................................... 3-1
Serial Ports.................................................................................... 3-2
Rear panel RS-232 port........................................................... 3-2
Front panel configuration port.............................................. 3-3
Simple Instruction Set™ Control. ........................................... 3-4
Host-to-interface communications........................................ 3-4
Start-up message.................................................................... 3-4
Error responses....................................................................... 3-4
Timeout................................................................................... 3-4
Using the command/response table...................................... 3-5
Symbol definitions..................................................................3-5
Windows®-Based Program Control. ..................................... 3-7
Installing the software........................................................... 3-7
Starting the program.............................................................. 3-7
Firmware upgrade.................................................................. 3-8
Appendix A • Reference Information..............................A-1
Specifications...............................................................................A-2
Part Numbers...............................................................................A-4
FOX 4G DA8 part numbers.....................................................A-4
Included parts.........................................................................A-4
Optional accessories...............................................................A-4
Compatible equipment...........................................................A-5
FOX 4G DA8 • Table of Contents
i
Table of Contents, cont'd
FOX 4G DA8
1
Chapter One
Introduction
About this Manual
About the FOX 4G DA8
Features
68-1461-01 Rev. A
02 09
All trademarks mentioned in this manual are the properties of their respective owners.
ii
FOX 4G DA8 • Table of Contents
Introduction
W
The FOX 4G DA8 outputs continuous invisible
light, which may be harmful and dangerous to the
eyes; use with caution.
Extron
SI 26X
Extron
FOX 4G DA8
Two-way Ceiling
Speakers
Fiber Optic Distribution Amplifer
122
MPA
PUTS
OUT
Ohms
4/8
US
C
TE
TS
REMO
INPU
• Do not look into the rear panel fiber optic
cable connectors or into the fiber optic cables
themselves.
Local
Monitor
8
Extron
FOX 500 Tx
X 4G
Fiber Optic
Transmitter
OUT
7 N/A
AL
TIC
OP
4 N/A
They will be identified where appropriate, but not
specifically described in this manual.
About the FOX 4G DA8
The Extron FOX 4G DA8 (figure 1-1) product family consists of
two models of ultra-high performance fiber optic distribution
amplifiers.
The FOX DA accepts a proprietary input optical signal from
a compatible Extron fiber optic transmitter (Tx). The optical
signal can include video, audio, and one-way (transmitter-toreceiver [Rx]) RS-232 communications.
1-2
FOX 4G DA8 • Introduction
1
0.3A
6 N/A
OUT
OUT
Mini Power
Amplifier
IN
OUT
T
INPU T
INPU
O
AUDI
L
INPU
R
ALARM
1
Tx
60
LINK
500
CAL
OPTI 2*
1
Hz
Extron
FOX 500 DVI
50/
LINK
Rx
OL
RS-232
CONTR
FOR
AL
DATA
OPTION
* RETURN
2
Rx
FOX
T
G
NA
Tx
RGB
UT
V
O
AUDI
H
OUTP
R
L
Rx
OL
RS-232
CONTR
ALARM
1
Tx
500
CAL
OPTI 1
2*
RS-232
THRU
PASS
B
OR
R
2
Rx
DVI Output
Fiber Optic Receiver
LINK
INPU
Tx
LINK
TS
THRU
T LOOP
INPU
RGB
0.3A
0V Hz
100-24
50/60
FOR
AL
DATA
OPTION
* RETURN
Rx
UTS
RGB
OUTP
B
G
0.3A
0V Hz
PC
RGB
R
100-24
50/60
V
H
RGB Input
Extron
FOX 500 Rx
Audio Input
RGB Output
Fiber Optic Receiver
AUDI
UT
OUTP R
L
ALARM
1
Tx
2
Rx
LINK
Rx
OL
RS-232
CONTR
500
CAL
OPTI 1
2*
NA
Tx
O
LINK
FOX
RS-232
THRU
PASS
FOR
AL
DATA
OPTION
* RETURN
Extron
FOX 500 DVI Rx
Flat Panel
Display
DVI Output
Projector
Fiber Optic Receiver
Rx
UTS
RGB
OUTP
B
G
0.3A
0V Hz
RGB
R
100-24
50/60
V
H
Extron
FOX 500 Rx
RGB Output
Fiber Optic Receiver
Flat Panel
Display
Projector
Figure 1-1 — Typical FOX 4G DA8 application
N Compatible optical signals are digital signals from
2.0 Mbps through 4.25 Gbps that are sent and received
via fiber optic SFP modules. The FOX DA supports all
compatible optical signals, whether transmitted or received
by an Extron fiber optic system component or not.
N The multimode and singlemode DAs are physically
N Many products are compatible with the Extron FOX DA.
TS
TPU
5 N/A
OU
OUT
3 N/A
OUT
2 N/A
OUT
0V
This manual contains information about the two models of
Extron FOX 4G DA8 fiber optic distribution amplifiers (DAs).
The DA is available in two transmission modes, which define
the transmission range of the DA:
and functionally identical, with the exception of the
effective range of transmission. In this manual, the terms
"FOX 4G DA8" and "FOX DA" refer to a DA of either
transmission mode.
Extron
MPA 122
Rx
-24
About this Manual
FOX 4G DA8 SM — A 1-input, 8-output singlemode DA,
with a very long range of up to 30 km (18.75 miles) on the
input and each output
Tx
100
FOX
•
RS
N/A
OUT
NA
FOX 4G DA8 MM — A 1-input, 8-output multimode DA,
with a range of up to 150 m (492') on the input and each
output
R
L
10V UTE
VOL/M
L
R
Tx
•
R
L
ER
POW
2
-23
RS-232
THRU
PASS
• Plug the attached dust caps into the optical
transceivers when the fiber optic cable is
unplugged.
DA
FO
8
N The video component of the signal from an Extron Tx can
be either VGA - UXGA RGB video, digital visual interface
(DVI) video, or SDI/HD-SDI video.
The serial component of the signal is for applications such
as projector control and transmitter control of the receiver.
The FOX DA actively splits the proprietary signal into eight
identical optical signals and outputs the signals on fiber optic
cables to compatible receivers.
N The eight optical outputs are identical.
N The FOX 4G DA8 does not support transmission of a
return (Rx-to-Tx) serial data stream.
N The switcher can receive and send the proprietary signal
from and to any compatible Extron fiber optic transmitter,
receiver, or switcher. See appendix A, "Reference
Information" for a list of compatible products.
FOX 4G DA8 • Introduction
1-3
Introduction, cont’d
The connected receiver(s) convert the proprietary signal(s)
back to video (RGB, DVI, or SDI/HD-SDI, depending on the
source transmitter and the receiver), audio, and serial RS-232
communication, and output the signals locally. For video
resolutions up to 1600 x 1200, the receivers' video outputs are a
perfect, pixel-for-pixel or digital recreation of the video signal
input to the FOX DA via a transmitter.
Features
Ultra high performance — Outputs up to eight perfect,
pixel-by-pixel RGBHV or digital video transmissions to
compatible receiver(s). The FOX DA can handle analog
video resolutions up to 1600 x 1200 at 60 Hz. Higher
resolutions can be transmitted, but with some loss of
video quality.
Optical input and outputs — The FOX DA inputs and outputs
the optical signal on LC video connectors.
Active and individually isolated outputs — The FOX 4G DA8
uses active signal splitting to maintain equal transmitter
power to all outputs, maximizing distance capabilities by
ensuring full availability of optical loss budget for each
output.
System video output — When the optical input is from a
FOX 500 or FOXBOX 4G Tx (rather than a FOX HD-SDI),
the video portion of the optical video output can be
decoded to either RGB video or DVI video, depending on
the receiver connected.
Rack mounting — The unit is rack mountable in any
conventional 19" wide rack, using Extron's full size rack
shelf.
Power — The 100 VAC to 240 VAC, internal power supply
provides worldwide power compatibility.
FOX 4G DA8
2
Chapter Two
Installation and Operation
Mounting the Unit
Rear Panel Features
Front Panel Features
System Operation
1-4
FOX 4G DA8 • Introduction
Installation and Operation
Mounting the Unit
C Installation and service must be performed by
authorized personnel only.
The 1U high, half-rack width unit can be placed on a tabletop,
mounted on a rack shelf, or mounted under or through a desk or
other furniture.
Mounting instructions
For optional rack mounting, mount the 1U high, half rack width
unit on either of the following rack shelves:
•
RSU 129 9.5" 1U universal rack shelf kit (part #60-190-01)
(figure 2-1)
•
RSB 129 9.5" 1U basic rack shelf (part #60-604-01)
1U Universal Rack Shelf
Tabletop placement
1/2 Rack Width Front False
Faceplate
Affix the four included rubber feet to the bottom of the unit and
place it in any convenient location.
Rack mounting
UL guidelines
The following Underwriters Laboratories (UL) guidelines
pertain to the installation of the FOX 4G DA8 into a rack
(figure 2-1).
1.
2.
Reduced air flow — Installation of the equipment in a rack
should be such that the amount of air flow required for
safe operation of the equipment is not compromised.
3.
Mechanical loading — Mounting of the equipment in
the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
4.
5.
2-2
Elevated operating ambient — If installed in a closed
or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater
than room ambient. Therefore, consider installing the
equipment in an environment compatible with the +122 °F
(+50 °C) maximum ambient temperature (Tma) specified
by Extron
Circuit overloading — Consideration should be given to
the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be
used when addressing this concern.
Reliable earthing (grounding) — Reliable earthing
of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections
other than direct connections to the branch circuit (such as
the use of power strips).
FOX 4G DA8 • Installation and Operation
Front false
faceplate
uses 2
screws.
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
NOTE: Using screws longer
than 3/16” will damage the
unit and void the warranty.
Figure 2-1 — Mounting the unit on a standard rack shelf
1.
If installed, remove the feet from the bottom of the unit.
2.
Mount the unit on either the left or right side of the shelf,
using two 4-40 x 3/16" screws in opposite (diagonal)
corners to secure the unit to the shelf.
3.
Install a false faceplate or another unit onto the rack shelf.
4.
Insert the shelf into the rack, aligning the holes in the shelf
with those of the rack.
5.
Secure the shelf to the rack using the supplied machine
screws.
FOX 4G DA8 • Installation and Operation
2-3
Installation and Operation, cont’d
Furniture mounting
Mount the 1U high, half-rack width unit under a desk or
podium using the optional Extron MBU 125 under desk
mounting kit (part #70-077-01) as follows:
Through-desk mounting
Mount the 1U high, half-rack width unit through a desk or
podium using the optional Extron MBD 129 through desk
mounting kit (part #70-077-02) as follows:
1.
If rubber feet were previously installed on the bottom of
the unit, remove them.
1.
If rubber feet were previously installed on the bottom of
the unit, remove them.
2.
Secure the mounting brackets to the unit with the machine
screws provided (figure 2-2).
2.
Secure the brackets to the unit with the provided
machine screws (figure 2-3). Leave the screws slightly loose.
Figure 2-2 — Under-desk mounting the unit
Hold the unit with the brackets attached against the
underside of the table or other furniture. Mark the location
of the screw holes of the bracket on the mounting surface.
4.
Drill four pilot holes, each 3/32" (2 mm) in diameter by
1/4" deep (6.3 mm) deep in the mounting surface at the
marked screw locations.
3.
5.
Insert provided #8 wood screws into the four pilot holes.
Tighten each screw into the mounting surface until just less
than 1/4" (6.3 mm) of the screw head protrudes.
Hold the unit and brackets on the underside of the surface
to which you are mounting the device and mark the four
screw holes and the table material to be removed.
4.
6.
Align the mounting screws with the slots in the brackets
and place the unit against the surface, with the screws
through the bracket slots.
Remove the table material. Test the fit by inserting the
front of the device through the hole. If necessary, use a
rasp or coarse file to enlarge the hole.
5.
7.
Slide the unit slightly in or out, then tighten all four screws
to secure the unit in place (figure 2-2).
Drill four pilot holes, each 3/32" (2 mm) in diameter by
1/4" deep (6.3 mm) deep, in the locations that you marked
in step 3.
6.
Using the provided #8 four wood screws, attach the
brackets to the mounting surface.
3.
2-4
FOX 4G DA8 • Installation and Operation
Figure 2-3 — Through-desk mounting the unit
FOX 4G DA8 • Installation and Operation
2-5
Installation and Operation, cont’d
Slide the device in or out until it is in the desired position.
Tighten the screws installed in step 2.
If the screws are inaccessible to a screwdriver:
b
d. Replace the unit inside the surface (step 6).
Optical transceiver block 1 Input connector —
Connect the far end of this fiber optic cable to
the sending connector on the transmitter or
other compatible Extron device.
Rear Panel Features
1
IN
2
OUT N/A
3
OUT N/A
OPTICAL OUTPUTS
4
5
OUT N/A
OUT N/A
FOX 4G DA8
6
OUT N/A
7
OUT N/A
8
OUT N/A
RS-232
50/60 Hz
1
Tx Rx
INPUT
3 2
3
3
3
3
3
3
3
4
Figure 2-4 — FOX DA’s connectors
W
This unit outputs continuous invisible light, which
may be harmful and dangerous to the eyes; use with
caution. For additional safety, plug the attached
dust caps into the optical transceivers when the
fiber optic cable is unplugged.
N Singlemode and multimode devices are not
interchangeable. Ensure that you connect transmitting
and receiving devices that are compatible with the
FOX DA.
Optical transceiver block 1 Input LED —
LINK
2
1
OUT
IN
DA
When lit, the link is active (light is received
from the transmitter).
3
INPUT
the light link for transceiver block 1. The
right-hand LEDs for transceiver blocks 2
through 8 may light, but do not indicate
an input to that connector.
c
Output connectors and LEDs —
Output connectors — For one-way video,
audio, and serial communications from the
FOX DA to the receivers, connect up to eight
fiber optic cables to the Output (left-hand) LC
connectors on transceiver blocks 1 through 8.
system. Typically, singlemode fiber has a yellow jacket and
multimode cable has an orange jacket.
OPTICAL
2* 1
LC connector on a transmitter or other device that outputs
a fiber optic signal. The term "receiving connector" refers
to an LC connector that receives an optical signal.
Receiver
Connect the far ends of these fiber optic
cables to the receiving connectors on the receivers or other
compatible Extron devices.
AC power connector — Plug a standard IEC power cord into
this connector to connect the FOX DA to a 100 VAC to 240 VAC,
50 or 60 Hz power source.
Output LEDs — These LEDs are always lit, whether the
output is active (unmuted) or not.
N In this manual, the term "sending connector" refers to an
2-6
For one-way video, audio, and serial
communications from the transmitter to the
FOX DA (for distribution to the receiver(s),
connect a fiber optic cable to the optical
transceiver block 1's Input (right-hand) LC
connector.
N The input (right-hand) LED indicates
N Ensure that you use the proper fiber cable for your
a
OPTIONAL FOR
* RETURN
DATA
LINK
c. Tighten the screws.
OUT
OPTICAL
1 2*
LINK
transciever block 1 is the only functional
input connector. The right-hand
LC connectors are not functional for
transceiver blocks 2 through 8.
b. Remove the transmitter or receiver from inside the
furniture.
0.3A
Transmitter
N The input (right-hand) LC connector for
a. Mark the location of the brackets relative to the screws.
100-240V
Input connector and LED —
LINK
7.
FOX 4G DA8 • Installation and Operation
FOX 4G DA8 • Installation and Operation
2-7
Installation and Operation, cont’d
d
RS-232 port — For serial control of the DA, connect a host
Front Panel Features
device, such as a computer, touch panel control, or RS-232
capable PDA, via this 3-pole captive screw connector.
Figure 2-5 shows how to wire this connector.
CONFIG
Pin
TX
RX
Gnd
RS-232
Tx Rx
FOX DA SERIES
Function
Transmit data
Receive data
Signal ground
FIBER OPTIC DISTRIBUTION AMPLIFER
1
2
Figure 2-6 — FOX DA front panel features
Do not tin the wires!
Ground ( )
Receive (Rx)
Transmit (Tx)
Controlling
Device
a
Power LED — This LED lights when power is applied to the
unit.
Ground ( )
Receive (Rx)
Transmit (Tx)
b
Configuration port — This 2.5 mm mini stereo jack serves
the same serial communications function as the rear panel
RS-232 port, but is easier to access than the rear port after
the unit has been installed and cabled. The optional 9-pin D
to 2.5 mm mini jack TRS RS‑232 cable, part #70-335-01
(figure 2-7), can be used for this connection.
Bidirectional
Figure 2-5 — RS-232 connectors
N The length of exposed wires is critical. The ideal length is
3/16" (5 mm).
6 feet
(1.8 m)
• If the stripped section of wire is longer than 3/16", the
exposed wires may touch, causing a short circuit.
• If the stripped section of wire is shorter than 3/16",
1
wires can be easily pulled out even if tightly fastened
by the captive screws.
• 9600 baud
• 1 stop bit
• no parity
• no flow control
9
5
This port is RS-232 only, with the following protocols:
Part #70-335-01
6
Tip
Ring
• 8 data bits
Sleeve (Gnd)
9-pin D
Connection
TRS Plug
Pin 2
Pin 3
Pin 5
Computer's RX line
Computer's TX line
Computer's signal ground
Tip
Ring
Sleeve
Figure 2-7 — Optional 9-pin TRS RS-232 cable
2-8
FOX 4G DA8 • Installation and Operation
This port is RS-232 only, with the following protocols:
• 9600 baud
• 1 stop bit
• no parity
• no flow control
• 8 data bits
FOX 4G DA8 • Installation and Operation
2-9
Installation and Operation, cont’d
N The maximum distance from the FOX DA to the
controlling device can vary up to 200' (61 m). Factors
such as cable gauge, baud rates, environment, and output
levels (from the unit and the controlling device) all affect
transmission distance. Distances of about 50' (15 m) are
typically not a problem. In some cases, the unit may be
capable of serial communications via RS‑232 up to 250'
(76 m) away.
System Operation
After the transmitter, the FOX DA, the receiver(s), and
their connected devices are powered up, the system is fully
operational. If any problems are encountered, ensure all
traditional and fiber cables are routed and connected properly:
•
Ensure that the video source and the display(s) are
properly connected to the transmitter, the FOX DA, and
the receiver(s), and that all equipment has power applied.
•
Ensure that the rear panel Input monitoring LED (item b
on page 2-7) is indicating correctly for your system
configuration.
N If problems persist, call the Extron S3 Sales & Technical
Support Hotline. See the rear cover of this manual for the
phone number in your region of the world.
FOX 4G DA8
3
Chapter Three
Remote Control
Serial Ports
Simple Instruction Set Control
Windows®-Based Program Control
2-10
FOX 4G DA8 • Installation and Operation
Remote Control
Serial Ports
Front panel configuration port
The FOX DA has two serial ports that can be connected to a host
device such as a computer running the HyperTerminal utility,
an RS-232 capable PDA, or a control system. These ports make
serial control of the DA possible. The serial ports are:
•
The rear panel RS-232 port on a 3-pin captive screw
connector
•
The front panel Configuration (RS-232) port, a 2.5 mm
mini stereo jack
The optional Extron 9-pin D to 2.5 mm mini jack TRS RS‑232
cable, part #70-335-01 (figure 3-2) can be used for connection to
the Configuration port.
6 feet
(1.8 m)
1
The protocol for both ports is as follows:
•
•
9600 baud
1 stop bit
•
•
no parity
•
no flow control
8 data bits
Part #70-335-01
6
9
5
Tip
Ring
Rear panel RS-232 port
Sleeve (Gnd)
Pin
TX
RX
Gnd
RS-232
Tx Rx
Function
Transmit data
Receive data
Signal ground
Do not tin the wires!
Controlling
Device
9-pin D
Connection
TRS Plug
Pin 2
Pin 3
Pin 5
Computer's RX line
Computer's TX line
Computer's signal ground
Tip
Ring
Sleeve
Figure 3-2 — Optional 9-pin TRS RS-232 cable
Ground ( )
Receive (Rx)
Transmit (Tx)
Ground ( )
Receive (Rx)
Transmit (Tx)
Bidirectional
Figure 3-1 — RS-232 connector pin assignments
3-2
FOX 4G DA8 • Remote Control
FOX 4G DA8 • Remote Control
3-3
Remote Control, cont’d
Simple Instruction Set™ Control
Using the command/response table
The command/response table begins on page 3-6. Lower case
letters are acceptable in the command field. Symbols are used
throughout the table to represent variables in the command/
response fields. Command and response examples are shown
throughout the table. The ASCII to HEX conversion table below
is for use with the command/response table.
Host-to-interface communications
The Extron Simple Instruction Set (SIS) commands consist of
one or more characters per field. No special characters are
required to begin or end a command character sequence. When
a command is valid, the unit executes the command and sends
a response to the host device. All responses from the unit to the
host end with a carriage return and a line feed (CR/LF = ]),
which signals the end of the response character string. A string
is one or more characters.
ASCII to HEX Conversion Table
Space
Start-up message
When a local event, such as a front panel operation or error
condition, occurs, the unit responds by sending a message to the
host. The unit-initiated messages are listed below:
(c) Copyright 2009, Extron Electronics FOX 4G DA8,
Vx.xx, 60-927-xx]]
The FOX DA issues the copyright message when it first powers
on. Vx.xx is the firmware version number, 60-927-xx is the part
number.
Error responses
When the unit receives a valid SIS command, it executes the
command and sends a response to the host device. If the unit is
unable to execute the command because the command is invalid
or it contains invalid parameters, the unit returns an error
response to the host. The error response codes are:
E10 - Invalid command]
E12 - Invalid output number]
E13 - Invalid range]
Timeout
Pauses of 10 seconds or longer between command ASCII
characters result in a timeout. The command operation is
aborted with no other indication.
3-4
FOX 4G DA8 • Remote Control
Symbol definitions
Symbols (variables), defined below, are used in the
command/response table on page 3-6. The symbols represent
variables in the unit-initiated messages and the command/
response table fields.
] = CR/LF (carriage return/line feed)
•
= space
X!
X@
=Output
1 through 8
= Mute status
X#
X$
0 = off (unmuted)
1 = on (muted)
= Firmware version
v.vv
= Transceiver module status
X%
X^
00000000 = no light input
10000000 = light input
= Temperature
nnnF = whole degree Fahrenheit
= Transceiver module status
0 = no module installed
1 = multimode
2 = singlemode
FOX 4G DA8 • Remote Control
3-5
Command
ASCII Command
FOX 4G DA8 • Remote Control
(host to unit)
Response
(unit to host)
Additional description
Channel mute
N The channel mute commands mute the data on the output only. The output continues to emit light.
Mute output
X!*1B
VmtX!*1]
Blank data on optical output X!.
X!*0B
X!B
VmtX!*0]
Output data on optical output X!.
Show video mute status
X@]
Mute all outputs
1*B
Vmt1]
Output X!'s data output mute status is X@
(0 = unmuted, 1 = muted).
Blank data on all optical outputs.
Unmute all outputs
0*B
Show mute status of all
outputs
EVM}
Vmt0]
X@1X@2X@3X@4 ... X@8]
Show output 1 through output 8 mute status.
Information request
I
V01X08•A00X00]
Show firmware version
Q
X#]
Q
1.23]
Request part number
N
60-927-nn]
Show input connections
status
Show temperature
0LS
X$]
20S
Show transceiver module
status
0*1I
X%]
X% = degrees Fahrenheit.
X^1X^2X^3X^4 ... X^8] Show all installed transceiver modules.
Unmute output
Output data on all optical outputs.
Information requests
Example:
V01X08 shows the number of available inputs (1) and
outputs (8) for this product.
A00X00 has no meaning for this product.
The factory-installed FOX 4G DA8 controller firmware
version is 1.23 (sample value only).
nn indicates the transmission mode.
01 = multimode, 02 = singlemode.
0000000 = no light on the input,
10000000 = light received.
0 = none, 1 = multimode, 2 = singlemode.
Remote Control, cont’d
3-6
Command/response table for SIS commands
Windows®-Based Program Control
The Extron FOX Extender program, which communicates with
the FOX DA via the unit's rear panel RS-232 port or front panel
Configuration port, provides an easy way to operate the DA.
The program is compatible with Windows 2000, Windows XP,
or later. Updates to this program can be downloaded from the
Extron Web site (www.extron.com).
Installing the software
The program is contained on the Extron Software Products
CD-ROM, disk B. Install the software as follows:
1.
Insert the CD-ROM into the drive. The installation
program should start automatically. If it does not self-start,
run Launch.exe from the CD.
The Extron software CD window appears (figure 3-3).
Figure 3-3 — Software CD window
2.
Click the Software tab (figure 3-3).
3.
Scroll to the desired program and click Install (figure 3-4).
Figure 3-4 — Software installation
FOX 4G DA8 • Remote Control
3-7
Remote Control, cont’d
4.
Follow the on-screen instructions. By
default, the Windows installation creates a
C:\Program Files\Extron\FOX_Extenders directory, and it
places the following four icons into a group folder named
“Extron Electronics\FOX Extender WCP”:
•
Check for FOX Extender updates
•
FOX Extender WCP
•
FOX Extender Help
•
Uninstall FOX Extender WCP
Starting the program
Start the Extron FOX Extender program as follows:
1.
Connect a Windows-based computer to either of the DA's
serial ports. See chapter 2, “Installation and Operation”,
for more details.
2.
Click Start > Programs > Extron Electronics >
FOX Extender WCP > FOX Extender WCP.
The Communication Setup window appears (figure 3-5).
Figure 3-6 — FOX Extender program window
Firmware upgrade
Firmware can be upgraded via the unit's front panel
Configuration port only, using the Extron Firmware Loader
utility from the FOX Extender program.
Upload replacement firmware as follows:
1.
Visit the Extron web site, www.extron.com, click the
Download Center tab, and then click the Firmware link
(figure 3-7). Select the appropriate firmware file(s) to
download and copy it (them) to your computer. Note the
folder to which you save the firmware file(s).
Figure 3-5— Communication Setup window
3.
Select the Com port to which your DA is connected. Click
OK.
The FOX Extender program window appears (figure 3-6).
Mute or unmute individual outputs or all outputs by
clicking the appropriate buttons.
N The channel mute command mutes the data on the output
only. The output continues to emit light.
3-8
FOX 4G DA8 • Remote Control
Figure 3-7 — Location of firmware upgrade files
2.
In the Windows Explorer or other file browser, double-click
the downloaded executable (*.exe) file(s) to self-extract the
firmware file(s).
3.
Connect a Windows-based computer to the front panel
Configuration port of the unit to be updated. See
chapter 2, "Installation and Operation", for more details.
4.
Start the FOX Extender program. See "Starting the
program", on page 3-8.
FOX 4G DA8 • Remote Control
3-9
Remote Control, cont’d
5.
Click Tools > Update Firmware. The Extron Firmware
Loader appears (figure 3-8).
6.
Click Browse. The open file window appears.
7.
Navigate to the folder where you saved the firmware
upgrade file. Select and open (double-click) the file. The
Firmware Loader returns to the top.
N Valid firmware files must have the file extension “.BIN”.
Any other file extension is not a firmware upgrade for your
FOX DA.
8.
Click Upload. The File Loader reports, "This process could
take several minutes. Please wait.." and then displays the
status of the upload.
9.
When the Firmware Loader reports, "Transfer complete!",
click the Exit button.
10. Cycle the FOX DA's power.
Figure 3-8 — Firmware upload
3-10
FOX 4G DA8 • Remote Control
FOX 4G DA8 • Remote Control
3-11
Remote Control, cont’d
FOX 4G DA8
A
Appendix A
Reference Information
Specifications
Part Numbers
3-12
FOX 4G DA8 • Remote Control
Reference Information
Specifications
Optical specifications
N
These amplifiers are class 1 laser products. They meet the
safety regulations of IEC-60825, FDA 21 CFR 1040.10, and
FDA 21 CFR 1040.11.
Number/type
Input������������������������������������ 1 singlemode or multimode fiber optic
Output��������������������������������� 8 singlemode or multimode fiber optic
Connectors������������������������������������� 8 LC connectors
Operating distance������������������������ 30 km (18.75 miles) with singlemode (SM)
cables
0.15 km (492') with multimode (MM)
cables
N
Operating distance is approximate. These are typical
distances. The maximum distance may be greater than these
typical numbers depending on factors such as fiber type, fiber
bandwidth, connector splicing, losses, modal or chromatic
dispersion, environmental factors, and kinks.
Nominal peak wavelength���������� 850 nm for MM model,
1310 nm for SM model
Data rate����������������������������������������� 4.25 Gbps
Transmission power
Singlemode������������������������� -5 dBm, typical
Multimode�������������������������� -5 dBm, typical
Maximum receiver sensitivity
Singlemode������������������������� -18 dBm, typical
Multimode�������������������������� -12 dBm, typical
Optical loss budget
Singlemode������������������������� 13 dB, maximum
Multimode�������������������������� 7 dB, maximum
Control/remote
Serial control ports������������������������ 1 RS-232, 3.5 mm captive screw connector,
3 pole (rear panel)
1 RS-232, 2.5 mm mini stereo jack
(front panel)
Baud rate and protocol����������������� 9600 baud, 8 data bits, 1 stop bit, no parity
A-2
FOX 4G DA8 • Reference Information
Serial control pin configurations� Captive screw connector: 1 = TX, 2 = RX,
3 = GND
Mini stereo jack: tip = TX, ring = RX,
sleeve = GND
Program control����������������������������� Extron's control/configuration program
for Windows®
Extron's Simple Instruction Set (SIS™)
General
Power���������������������������������������������� 100 VAC to 240 VAC, 50-60 Hz, 20 watts,
internal
Temperature/humidity���������������� Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling������������������������������������������� Convection, vents on top and sides
Mounting
Rack mount������������������������ Yes, with optional 1U, 9.5" deep rack shelf)
Furniture mount���������������� Yes, with optional under-desk mounting
kit and through-desk mounting kit
Enclosure type������������������������������� Metal
Enclosure dimensions������������������� 1.7" H x 8.7" W x 9.5" D
(1U high, half rack wide)
(4.3 cm H x 22.1 cm W x 24.1 cm D)
(Depth excludes connectors.)
Product weight������������������������������ 2.3 lbs (1 kg)
Shipping weight���������������������������� 4 lbs (2 kg)
Vibration����������������������������������������� ISTA 1A in carton
(International Safe Transit Association)
Regulatory compliance
Safety����������������������������������� CE, CUL, UL
EMI/EMC�������������������������� CE, C-tick, FCC Class A, FDA Class 1,
ICES, VCCI,
MTBF����������������������������������������������� 30,000 hours
Warranty����������������������������������������� 3 years parts and labor
N
All nominal levels are at ±10%.
N
Specifications are subject to change without notice.
FOX 4G DA8 • Reference Information
A-3
Reference Information, cont’d
Part Numbers
Compatible equipment
FOX 4G DA8 part numbers
The FOX 4G DA8 is available in a singlemode (SM) and a
multimode (MM) model:
FOX 4G Models
Part number
FOX 4G DA8 SM
60-927-02
FOX 4G DA8 MM
60-927-01
Included parts
These items are included in each order for a FOX 4G DA8:
Included parts
Part number
IEC power cord
3-pole captive screw audio connector
Installation guide
The FOX 4G DA8 is compatible with a variety of Extron fiber
optic receivers and matrix switchers, as shown below:
Fiber optic RGB video models
FOX 500 (RGB) Tx/Rx SM (set)
60-746-02
FOX 500 (RGB) Tx SM (individual unit)
60-746-12
FOX 500 (RGB) Rx SM (individual unit)
60-746-22
FOX 500 Tx/Rx (RGB) MM (set)
60-746-01
FOX 500 Tx (RGB) MM (individual unit)
60-746-11
FOX 500 Rx (RGB) MM (individual unit)
60-746-21
FOXBOX 4G Tx VGA SM
60-934-12
FOXBOX 4G Rx VGA SM
60-934-22
FOXBOX 4G Tx VGA MM
60-934-11
FOXBOX 4G Rx VGA MM
60-934-21
Extron Software Products CD
(FOX Extender program)
FOX 4G DVI models
(1) 10' LC-LC duplex patch cables
(SM or MM, depending on the model)
FOX 500 DVI Tx SM (individual unit)
60-859-12
FOX 500 DVI Rx SM (individual unit)
60-859-22
FOX 500 DVI Tx MM (individual unit)
60-859-11
Optional accessories
Part number
FOX 500 DVI Rx MM (individual unit)
60-859-21
Part number
FOXBOX 4G Tx DVI SM
60-935-12
9-pin D to 2.5 mm mini jack TRS RS‑232
cable
70-335-01
FOXBOX 4G Rx DVI SM
60-935-22
RSU 129 9.5" 1U universal rack shelf kit
60-190-01
RSB 129 9.5" 1U basic rack shelf
60-604-01
MBU 125 under desk mounting kit
70-077-01
FOX 2G models
Part number
MBD 129 through desk mounting kit
70-077-02
FOX 2G Tx AV SM
60-941-12
FOX 2G Rx AV SM
60-941-22
Accessories
FOXBOX 4G Tx DVI MM
60-935-11
FOXBOX 4G Rx DVI MM
60-935-21
FOX 2G Tx AV MM
60-941-11
FOX 2G Rx AV MM
60-941-21
FOX HD-SDI models
A-4
Part number
FOX 4G DA8 • Reference Information
Part number
FOX HD-SDI SM
60-901-01
FOX HD-SDI MM
60-900-01
FOX 4G DA8 • Reference Information
A-5
Reference Information, cont’d
FOX 4G Matrix 14400 switcher
FOX 4G Matrix 14400 enclosure
A-6
Part number
60-969-01
Singlemode I/O card
70-771-02
Multimode I/O card
70-771-01
Other fiber optic models
Part number
FOX 4G SW8 SM
60-984-02
FOX 4G SW8 MM
60-984-01
FOX 500 DA6 SM
60-863-02
FOX 500 DA6 MM
60-863-01
FOX 4G DA8 • Reference Information
Download PDF